Miele Washer t 250 c User Manual

Operating instructions  
for condenser tumble dryer  
T 250 C  
G
To avoid the risk of accidents or  
damage to the machine it is  
essential to read these operating instructions  
before it is installed or used for the first time.  
M.-Nr. 05 993 030  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning and Safety instructions  
Before connecting the machine,  
ensure that the connection data on  
the data plate (fusing, voltage and  
frequency) matches the mains  
electricity supply. If in any doubt,  
consult a qualified electrician.  
To avoid the risk of accidents and  
damage to the machine please read  
these instructions carefully before  
using it for the first time. They  
contain important information on its  
safety, use and maintainence.  
Keep these operating instructions in  
a safe place and ensure that new  
users are familiar with the content.  
Pass them on to any future owner of  
the machine.  
The electrical safety of this  
machine can only be guaranteed  
when continuity is complete between  
the machine and an effective earthing  
system which complies with local and  
national regulations. It is most important  
that this basic safety requirement is  
regularly tested, and where there is any  
doubt the household wiring system  
should be inspected by a qualified  
electrician. The manufacturer cannot be  
held liable for the consequences of an  
inadequate earthing system (e.g.  
electric shock).  
Correct use  
The tumble dryer is only intended  
for drying fabrics which have been  
washed in a water solution, marked on  
the manufacturer's wash care label as  
being suitable for tumble drying.  
"Dry Cleaning Kits" for freshening up  
garments in a tumble dryer are  
increasingly available on the market. If  
using, do so at your own risk and follow  
the instructions provided on the  
packaging.  
Do not connect the machine to the  
mains electricity supply by an  
extension lead. Extension leads do not  
guarantee the required safety of the  
machine (e.g. danger or overheating).  
Any other applications may be  
dangerous. The manufacturer is not  
liable for damage resulting from  
improper use or operation.  
The machine is built in accordance  
with current safety requirements.  
Unauthorised repairs could result in  
unforeseen dangers for the user, for  
which the manufacturer cannot accept  
liability. Repairs should only be  
undertaken by a Miele approved  
technician.  
This machine is not a toy! To avoid  
the risk of injury, do not allow  
children to play on or near it, or to  
play with the controls. Supervise its  
use by the elderly or infirm.  
Ensure current is not supplied to the  
machine while maintenance or repair  
work is being carried out.  
Technical safety  
Faulty components must only be  
exchanged for Miele original spare  
parts. Only when these parts are fitted  
can the safety standards of the  
machine be guaranteed.  
Before setting up the machine  
check it for any externally visible  
damage. Do not install or use a  
damaged machine.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Warning and Safety instructions  
If the connection cable is faulty it  
condensed water is allowed to freeze in  
the pump, hoses and / or condensed  
water container.  
must only be replaced by a Miele  
approved service technician to protect  
the user from danger.  
If the water is drained externally  
through the drain hose instead of  
being collected in the condensed water  
container, make sure the drain hose is  
securely attached if you hang it in a  
sink or basin to avoid the hose slipping  
and the water causing damage.  
In the event of a fault or for  
cleaning purposes, the machine is  
only completely isolated from the  
electiricty supply when:  
– it is switched off at the wall socket  
and the plug is withdrawn, or  
Condensed water is not drinking  
water. It can cause health  
problems in both people and animals.  
– it is switched off at the mains, or  
– the mains fuse is withdrawn.  
Always keep the area around the  
machine free of dust and fluff. Dust  
drawn into the machine can, over time,  
cause blockages in the condenser unit.  
Operation  
This equipment is not designed for  
maritime use or for use in mobile  
installations such as caravans, aircraft  
etc. However it may be suitable for  
such usage subject to a risk  
assessment of the installation being  
carried out by a suitably qualified  
engineer.  
The dryer must not be used without  
the fluff filters in place or if the fluff  
filters are damaged in any way.  
The fluff filters must be thoroughly  
dried after cleaning. If they are still  
damp or wet when replaced there is a  
risk of faults occurring when the  
machine is used.  
The dryer must not be used without  
the condenser unit in place.  
Do not install the machine in a  
room where the temperature may  
drop down to or below freezing. At very  
cold temperatures the machine may be  
difficult to start.  
There is a risk of damage if the  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning and Safety instructions  
Always close the door after use.  
This way you will avoid the danger  
Using accessories  
Accessory parts may only be fitted  
when expressly approved by Miele.  
If other parts are used, guarantee,  
performance and product liability  
claims may be invalidated.  
of:  
– children climbing onto or into the  
dryer or hiding things in it.  
– pets or other small animals climbing  
into it.  
The manufacturer cannot be held  
liable for damage caused by  
non-compliance with these Warning  
and Safety instructions.  
Do not let anyone sit or lean on the  
door, as this can cause the  
machine to tip up.  
There is danger of fire with fabrics  
which:  
– contain a large proportion of rubber,  
foam rubber or rubber like materials.  
– have been treated with inflammable  
cleaning agents.  
– have been splashed with hair  
lacquer, hair spray, nail varnish  
remover or similar substances.  
– which contain padding or fillings  
(e.g. pillows, jackets). If these were  
damaged the filling could leak out  
with the risk of igniting in the dryer.  
– are soiled with oil or grease.  
In countries where there are areas  
which may be subject to infestation  
by cockroaches or other vermin, pay  
particular attention to keeping the  
machine and its surroundings in a  
clean condition at all times. Any  
damage which may be caused by  
cockroaches or other vermin will not  
be covered by the machine  
guarantee.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caring for the environment  
Disposal of the packing  
material  
Energy saving tips  
^ Make sure that your laundry is  
thoroughly spun before drying.  
The transport and protective packing  
has been selected from materials which  
are environmentally friendly for disposal  
and can normally be recycled.  
The higher the spin, the greater the  
savings that can be made in energy  
and time during drying.  
Ensure that any plastic wrappings,  
bags etc. are disposed of safely and  
kept out of the reach of babies and  
young children. Danger of suffocation!  
^ Load according to the optimum  
amount of laundry recommended for  
the programme being used (see  
Programme chart).  
Rather than just throwing these  
materials away, please ensure they are  
offered for recycling.  
Underloading is uneconomical.  
Overloading gives a poorer quality of  
drying and may cause unnecessary  
creasing.  
Disposal of your old machine  
^ To save energy and time:  
Old machines contain materials which  
can be reclaimed or recycled. Please  
contact your dealer, your local waste  
collection centre or scrap merchant  
about potential recycling schemes.  
– Make sure the room in which the  
dryer is located is well ventilated.  
– Make sure the fluff filters are clean  
before using the dryer.  
Ensure that the machine presents no  
danger to children while being stored  
for disposal.  
Before throwing an old machine  
away unplug it and render the plug  
useless. Cut off the cable directly  
behind the machine to prevent misuse.  
This should be done by a competent  
person.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Description of the appliance  
Control panel  
aSTART button  
dProgamme sequence indicator  
lamps  
Press the START button to start a  
programme.  
The Start indicator lamp will flash as  
soon as a programme can be  
started. It lights up constantly once  
the programme has started.  
show the drying stage reached;  
and Check lamps:  
See "Problem solving guide" for  
information on the check lamps.  
eI-On/0-Off button  
bButtons for activating and  
To switch the appliance on or off or to  
interrupt a programme.  
deactivating additional options  
Indicator lamp lit up = activated  
not lit up = deactivated  
fDoor Button  
to open the door / to cancel a  
programme.  
cProgramme selector  
The programme selector can be  
turned clockwise or anti-clockwise.  
Pressing this button will open the  
door even when the appliance is  
switched off at the mains.  
If the appliance is switched on at the  
mains and the door is opened the  
drum lighting will come on. It will go  
out a few minutes later to save  
energy.  
To save energy, the light ring around  
the programme selector goes out a  
few minutes after the dryer has been  
switched on, if no programme is  
selected or if a programme is not  
started. The light ring also goes out a  
few minutes after a programme has  
finished.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Description of the appliance  
Future updates (PC)  
The indicator lamp marked PC on the  
fascia panel is the interface used by  
the Miele service technicians for  
updating the machine’s programme  
data.  
Electronic system lock and  
programmable functions  
The following can be programmed into  
your machine using the programme  
selector in combination with the  
buttons.  
Electronic system lock  
Prevents the machine being operated  
by others.  
Programmable functions  
Programmable functions enable the  
machine to be adapted to suit personal  
requirements.  
See the relevant section for detailed  
instructions.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Notes on laundry care  
Wash care labels  
Items filled with down.  
The fabric lining on these garments  
may shrink depending on the quality.  
They can be partially dried using the  
Smoothing programme.  
Before drying check the drying  
symbol on the wash care label.  
Significance of symbols:  
Pure linen should only be machine  
dried if specified as suitable by the  
manufacturer on the wash care label,  
as the surface of the fabric may  
otherwise "roughen". These items can  
be partially dried using the Smoothing  
programme.  
q Dry at normal temperature  
r Dry at low temperature  
sDo not tumble dry  
If no symbol is featured, dry at your  
own risk applying the following  
principles:  
Woven and loopknit materials (e.g.  
T-shirts, knitted garments) have a  
tendency to shrink, depending on their  
quality and this is made worse by  
over-drying. When purchasing these  
garments it is advisable to take their  
shrinkage properties into account.  
Cotton and minimum iron items should  
be dried using the appropriate  
programme for the degree of drying  
required. See programme chart.  
For delicates and fabrics with the  
following wash care label r dry using  
the Low temperature option.  
Minimum iron fabrics and 100% cotton  
shirts or blouses tend to crease more,  
the larger the load being dried,  
particulary when the weave of the  
fabric is very fine. Reduce the load or  
use the MINIMUM IRON - Hand iron  
programme with a max. load of 1 kg. If  
this is unsatisfactory use the Special  
care "Smoothing" setting, then hang the  
garments on a hanger to dry.  
Never overload the drum. Do not  
exceed the maximum recommended  
loads given in the "Programme  
chart". Overloading can cause  
unnecessary wear and tear to the  
laundry, give a disappointing drying  
result and cause more creasing.  
Do not put soaking wet items into  
the tumble dryer. Spin them  
thoroughly after washing using the  
appropriate spin speed.  
Starched laundry can be dried in the  
tumble dryer. In order to achieve the  
usual finish, double the amount of  
starch should be used.  
New dark coloured garments should be  
dried separately from light coloured  
garments to avoid the danger of col-  
ours running.  
Tips on drying  
Woollens and wool blends tend to  
become matted and shrink if dried in a  
tumble dryer. They can, however, be  
partially dried using the Woollens hand  
care programme.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programme chart  
Special notes  
Programmes  
Drying levels  
COTTONS  
Extra dry  
Fabric type  
maximum load: 5 kg (1)  
Multi-layered fabrics, which Do not dry jersey wear in the  
would not be thoroughly  
dried using the "Normal +"  
programme.  
Extra dry programme -  
tendency to shrink.  
Normal +  
Normal (2)  
Single and multi-layered  
fabrics, e.g. mixed load of  
cotton fabrics (e.g.  
-
towelling, jerseywear).  
Load of similar fabrics  
(jersey wear, flannelette  
sheets, towelling).  
If laundry is still too damp,  
then:  
- finish drying using Timed  
drying "Warm air".  
- Use the"Normal +"  
programme next time.  
Hand iron  
Hand iron rr (2)  
Cotton or linen fabrics (e.g.  
table linen, bedlinen,  
-
If laundry is still too damp  
for hand ironing, then select  
"Hand iron " in the future.  
starched laundry etc).  
r
Machine iron  
Cotton or linen fabrics,  
The laundry should be rolled  
including starched laundry, up to prevent it from drying  
for machine ironing. out before it can be ironed.  
(1) Weight of dry laundry  
(2) Note for test institutes: These programmes are to be  
used when testing according to EN 61121 standard  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programme chart  
Programme  
Fabric type  
Special notes  
Drying levels  
MINIMUM IRON  
maximum load: 2.5 kg (1)  
Normal +  
Minimum iron items which are Spin minimum iron fabrics for  
made of synthetic or blended  
fabrics (e.g. pullovers,  
dresses, trousers) which are  
not dried adequately in the  
"Normal" programme.  
at least 30 seconds in the  
washing machine before  
drying.  
Normal (2)  
Hand iron  
Minimum iron shirts, table  
cloths etc. made of blended  
fabrics (e.g.  
Spin minimum iron fabrics for  
at least 30 seconds in the  
washing machine before  
drying.  
cotton/synthetics).  
Minimum iron shirts, table  
cloths etc. made of blended  
fabrics (e.g. cottons and  
Spin minimum iron fabrics for  
at least 30 seconds in the  
washing machine before  
synthetics), which are still to drying. For extra special care  
be hand ironed.  
of delicate fabrics and to  
reduce creasing even more,  
reduce the load to 1 kg. See  
also "Special care  
programmes")  
TIMED DRYING  
Warm air  
maximum load: 5 kg (1)  
Individual items  
(e.g. bathing costumes, bath  
towels, tea-towels).  
-
Multi-layered fabric whose  
layers have different drying  
characteristics.  
Cool air  
Items which are to be aired  
only.  
-
(1) Weight of dry laundry  
(2) Note for test institutes: These programmes are to be  
used when testing according to EN 61121 standard.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme chart  
Special notes  
Programme  
Fabric type  
Special care programmes  
Woollens  
hand care  
maximum load: 2 kg (1)  
Woollen fabrics  
To refresh and fluff up woollen  
garments quickly. Remove garments  
immediately at the end of the  
programme. Do not repeat.  
Woollen fabrics are not dried  
completely by this programme.  
Smoothing  
maximum load: 2.5 kg (1)  
Cottons and linen fabrics. Smooths out creasing caused during  
Minimum iron items made  
of cotton, blended fabrics  
or synthetics, e.g. cotton  
trousers, shirts.  
the spin cycle in the washing  
machine.  
Fabrics are not completely dried in  
this programme.  
Remove garments immediately at  
the end of the programme and place  
on a line or hangers to dry.  
(1) Weight of dry laundry  
Selecting additional options  
Programme  
Additional option button(s)  
COTTONS  
Anti-crease, Short, Low temperature, Buzzer  
MINIMUM IRON  
TIMED DRYING - Warm air  
- Cool air  
Woollens hand care  
Smoothing  
Anti-crease, Short, Low temperature, Buzzer  
Anti-crease, Low temperature, Buzzer  
Buzzer  
Buzzer  
Buzzer  
For delicates and fabrics with the following wash care label r select the Low  
temperature option.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to dry correctly  
A Prepare the laundry  
Do not overload the drum.  
^ As far as possible, sort laundry for:  
- the type of fibre or weave,  
- the degree of dryness required,  
- similar size of items,  
Overloading can cause unnecessary  
wear and tear to the laundry and  
give a disappointing drying result.  
- the moisture content after  
spinning.  
This will help towards achieving an  
even drying result.  
See the "Programme chart" for  
maximum recommended loads.  
^ Before closing the door check that  
the fluff filter is correctly positioned in  
the door.  
Fasten duvet covers etc. to prevent  
small items from being rolled up inside  
them.  
Do up zips, hooks and eyes etc.  
Tie fabric belts, apron strings.  
Sew in or remove underwiring from  
bras.  
Make sure there is no detergent  
dispenser ball etc. in with the  
laundry, as this could melt and  
damage the machine and the  
laundry.  
B Load the drum and switch  
on the dryer  
When closing the door make sure  
items of laundry cannot be trapped  
by the door, as this will cause  
damage to the laundry.  
^ Press the door button and open the  
door.  
^ Shut the door either with a gentle  
swing or lean against it and push it  
shut.  
^ Load the laundry loosely into the  
drum.  
^ Switch the dryer on by pressing the  
"l-On/0-Off" button.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to dry correctly  
C Select a programme  
D Select any additional  
option(s)  
^ Turn the programme selector to the  
required programme.  
^ Press the relevant button(s) for the  
additional option(s) required.  
COTTONS and  
MINIMUM IRON  
It is not possible to activate additional  
options which are incompatible with the  
drying programme selected. If an  
inappropriate combination of options is  
selected (e.g. "Short" and "Low  
temperature") only the last option  
selected will be activated.  
The electronic unit uses the residual  
moisture content to estimate the  
programme duration. This is an  
approximate drying time. See  
"Consumption data" chart for  
programme durations.  
Woollens hand care and Smoothing  
Anti-crease  
See the "Consumption data" chart for  
programme durations.  
Once a programme has ended, the  
drum will turn at regular intervals for  
approx. 60 minutes to prevent the  
laundry from settling into creases or  
folds.  
TIMED DRYING  
The programme duration is shown in  
the control panel display.  
Always select anti-crease if laundry is  
not going to be removed from the drum  
as soon as the programme has  
finished. Anti-crease can be activated  
or deactivated after a programme has  
started.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to dry correctly  
Short  
The drying stage reached is shown by  
the sequence indicator lamps on the  
right hand side of the control panel.  
For drying fabrics which can  
withstand high temperatures, e.g.  
pure linens and cottons. Do not use  
on minimum iron or delicate fabrics.  
At the end of the drying phase, a  
cooling down phase commences to  
cool the laundry down (the Cool air  
indicator lamp lights up).  
– Because the heater rating is  
increased clothes dry faster thus  
shortening drying times.  
The drying level required has now been  
reached.  
Low temperature  
F At the end of a programme  
For drying delicate fabrics with the  
symbol r (e.g. acrylic garments) at a  
lower temperature.  
When the drying programme has  
finished the Anti-crease / finish  
sequence indicator lamp will come on  
and the buzzer will sound.  
– Because the heater rating is reduced  
clothes dry more slowly thus  
lengthening drying times.  
^ Press the Door button and open the  
drum door.  
^ Remove the laundry.  
Buzzer  
Make sure that the drum is empty. If  
items are left in the dryer, they could  
be damaged by overdrying when  
the dryer is next used.  
An audible tone sounds repeatedly at  
the end of a programme.  
The buzzer can be switched on or off  
after a programme has started.  
^ After every cycle remove the fluff  
from the fluff filter in the door and in  
the door opening (see "Cleaning and  
Care").  
The volume (and pitch) of the buzzer  
can be adjusted before a programme is  
started:  
^ Empty the condensed water  
container (where there is no external  
drainage of the water).  
^ Select the programme.  
^ Press the Buzzer button (the Buzzer  
indicator lamp will light up), until the  
desired volume / pitch is achieved.  
Then release the button.  
^ The condenser unit should be  
cleaned on a regular basis (see  
"Cleaning and Care").  
E Start the programme.  
^ Press the START button.  
The drying cycle begins.  
^ After each use, switch the dryer off  
by pressing the l-On / 0-Off button.  
^ Always close the door after use.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to dry correctly  
Additional notes  
C Select a programme  
^ Turn the programme selector to the  
required programme.  
. . . Clean out airways indicator lamp  
This indicator lamp comes on to warn  
you that the dryer is not working  
efficiently.  
Additional option(s) can be selected  
(point D) if required.  
D Select additional option(s)  
This may be because:  
^ Press the relevant button(s) for the  
additional function(s) required.  
– the fluff filters are clogged;  
– the condenser unit is clogged.  
E Start the programme  
^ Press the START button.  
F At the end of the programme  
Brief instructions  
Recommendation:  
– the indicator lamp Anti-crease /  
Finish lights up and the buzzer  
sounds.  
To help you become familiar with  
operating the dryer, please make sure  
that you also read the detailed  
instructions at the beginning of this  
section.  
^ Open the door and remove the  
laundry.  
A Sort the laundry  
^ Switch the dryer off by pressing the  
l-On/0-Off button and close the door.  
B Load the dryer and switch it on  
^ Press the Door button and open the  
door.  
^ Load the drum and close the door.  
^ Switch the dryer on with the  
l-On/0-Off button.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
How to dry correctly  
Changing a programme  
Adding or removing items  
If the programme selector is turned to a ^ Press the Door button and open the  
different programme after a programme  
has begun, this will not affect the  
programme. The Anti-crease / Finish  
indicator lamp will flash. The indicator  
lamp will go out when the selector is  
returned to its original position.  
door.  
,Do not touch the back of the  
drum when adding or removing  
items. The drum could be very hot -  
danger of burning.  
After a programme has started, not all  
additional options can be switched on  
or off (see section "How to dry  
correctly").  
^ Items can now be added or removed  
early.  
To continue drying:  
^ Close the door.  
Interrupting a programme  
^ Press the START button.  
– The programme will continue.  
^ Switch the machine off with the I-On /  
0-Off button.  
To continue drying:  
^ Switch the machine back on with the  
I-On / 0-Off button.  
The programme will continue, as long  
as the cooling down phase has not  
been reached.  
To cancel a programme and select a  
different programme  
^ Turn the programme selector to  
Finish.  
The programme has been  
successfully cancelled when only the  
Anti-crease/Finish indicator lamp is  
on.  
^ Turn the programme selector to the  
required programme.  
^ Switch additional options on or off as  
required.  
^ Press the START button.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Electronic system lock  
The system lock prevents anyone  
from interfering with the dryer.  
If the system lock has been activated it  
is not possible to start a programme.  
The following steps (A,B,C...) must  
be carried out in the correct order.  
To activate the system lock  
AEnsure that the door is closed and  
that the programme selector is  
turned to Finish.  
BSwitch the machine on.  
CPress the Short button and keep it  
pressed in whilst carrying out steps  
D to F.  
DSlowly turn the programme selector  
clockwise step by step until it  
reaches the COTTONS Normal  
position.  
ESlowly turn the programme selector  
anti-clockwise step by step to Finish.  
FSlowly turn the programme selector  
anti-clockwise step by step to the  
MINIMUM IRON Hand iron position.  
The Locked indicator lamp will flash.  
GThen release the Short button.  
The system lock is now activated.  
HSwitch the machine off with the I-On /  
0-Off button.  
To deactivate the system lock  
^ Repeat steps A-G.  
The Locked indicator lamp will go out  
after step F.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning and care  
Emptying the condensed  
water container  
The condensed water will be collected  
in the condensed water container  
unless the machine has been fitted with  
a drain hose (see installation).  
The condensed water container  
should be emptied after every  
drying cycle or as soon as the  
Empty out container indicator lamp  
comes on.  
The drying programme will be  
^ Open the shutter and empty out the  
water.  
interrupted if the maximum level of the  
condensed water container is reached.  
The Empty out container indicator lamp  
comes on and the buzzer sounds.  
^ To replace the container hold it at a  
slight angle (as when removing it)  
and push it in gently until you feel it  
click into position.  
^ Before starting a new programme,  
first switch the machine off and then  
on again. The Empty out container  
indicator lamp will go out.  
Condensed water should not be  
consumed. It could lead to health  
problems for people and animals.  
Condensed water can be put to  
household use (e.g. used in a steam  
iron or humidifier). To ensure that any  
residual particles of fluff in the  
condensed water are removed before  
use, pass it through a fine sieve or  
paper filter first.  
^ Grip the container firmly with both  
hands, as shown, and pull it out  
slightly towards the right-hand side.  
^ Hold the container with both hands  
and carry it in a horizontal position.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning and care  
Cleaning the fluff filters  
^ Remove any fluff from the hollow part  
of the door holder. A cleaning brush  
is available as an optional extra from  
your Miele dealer or the Miele Spare  
Parts Department.  
The fluff which is created by the drying  
process is collected by the fluff filters in  
the door and the door opening. Clean  
the filters after each drying programme.  
Tip: You can also use a vacuum  
cleaner.  
Cleaning them whilst dry  
^ Once clean, push the filter back into  
the door holder until it clicks into  
position. Ensure it is facing the  
correct way.  
^ Open the door and pull the fluff filter  
out of the door as illustrated.  
^ Use your fingers to remove the fluff  
from the two fluff filters in the door  
opening.  
^ Close the door.  
^ Use your fingers to remove the fluff  
from the surface of the filter.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning and care  
Cleaning them with water  
^ Place the filters back in the door  
opening (the left and right filters are  
identical) with the finger holders  
facing upwards. See illustration.  
If there is a great deal of compacted  
fluff on any of the filters, they can be  
removed and cleaned under hot  
running water.  
Cleaning the tumble dryer  
^ To remove the fluff filter from the door  
holder see previous page.  
Disconnect the machine from the  
mains electricity supply.  
^ Clean the housing and control panel  
with a slightly damp cloth and a mild  
detergent or soapy water.  
^ The drum and other stainless steel  
parts can be cleaned with a suitable  
proprietary stainless steel cleaner  
following the manufacturer's  
instructions.  
Do not use solvents, abrasive  
cleaners, glass cleaners or  
all-purpose cleaners. These could  
damage plastic sufaces and other  
parts. The machine must never be  
hosed down.  
^ Grip the holder and push the filter in  
the door opening upwards in the  
direction of the arrow to remove it. Do  
the same on the opposite filter.  
^ Dry all parts with a soft cloth.  
^ Rinse the filters under hot, running  
water.  
^ A microfibre E-Cloth is available from  
the Miele UK Spare Parts Department  
which is suitable for cleaning  
surfaces such as stainless steel,  
glass, plastic and chrome without the  
use of chemicals. It can be washed  
300 times.  
^ Then shake the filters until no more  
water droplets are visible.  
^ Dry the filters thoroughly with care.  
,Do not replace them if they are  
damp or wet. Damp or wet filters  
could cause operational faults.  
^ Push the large filter back into the  
door holder until it clicks into position.  
Ensure it is facing the correct way.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning and care  
Cleaning the condenser unit  
Detergent residue, hair and fine fluff  
from the dryer can get through the fluff  
filters and block the condenser unit.  
Dust from the room in which the dryer is  
installed can also get into the  
condenser unit and cause a blockage.  
Check the condenser unit at least  
twice a year. If the dryer is used  
frequently then clean the condenser  
unit after approx. 100 drying cycles.  
^ Turn the lever on the inner cover  
downwards to the vertical position.  
Removing the condenser unit  
^ Pull the cover forwards  
^ Then remove it by pulling it  
diagonally upwards.  
^ Open the service panel by pressing  
the two lower corners at the same  
time (see illustration).  
The hooks at the side will prevent the  
panel from falling off.  
^ Turn the lever on the condenser unit  
to the vertical position.  
^ Now the remove the panel by pulling  
it diagonally upwards.  
^ Then place it to one side.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning and care  
If you cannot see any fluff:  
^ Replace the condenser unit (see  
following page).  
If you can see some fluff:  
^ Clean the condenser unit as  
described below.  
Cleaning the condenser unit  
^ When rinsing the condenser unit,  
make sure you position it as shown in  
the next two illustrations.  
^ Pull the condenser unit out of its  
housing by the handle.  
Checking the condenser unit  
^ Use a shower head or similar to rinse  
the unit out as shown.  
^ Hold the condenser unit up to the  
light as shown.  
^ Check to see if there is any fluff  
inside it.  
The arrows in the illustration above  
indicate where to look.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning and care  
Replacing the condenser unit  
^ With the handle facing upwards,  
push the condenser unit back into  
position in its housing.  
^ Turn the lever down to the horizontal  
position, making sure that the hook  
on the lever clicks into the groove.  
When replacing the cover after  
cleaning, ensure that the rubber seal  
fits correctly into the groove.  
^ Replace the cover making sure the  
hooks locate correctly. Hold it at an  
angle and push it gently downwards.  
^ Then flush the unit through from the  
front.  
^ Then turn the lever upwards into the  
horizontal position to lock the cover.  
^ Check the condenser unit again for  
any visible fluff and if necessary flush  
it through again until it has all gone.  
^ Replace the service panel and press  
the upper edge until it clicks into  
position.  
^ Remove any soiling still visible inside  
the housing unit.  
^ Also make sure the rubber seals are  
clean.  
It is important to ensure that both the  
condenser unit and the cover are  
correctly positioned and locked.  
Otherwise water may leak from the  
machine.  
The rubber seals must not be  
removed and must be free of kinks.  
^ Shake any excess water out of the  
unit until no more water droplets are  
visible.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Problem solving guide  
With the help of the following notes minor faults in the performance of the  
machine, some of which may result from incorrect operation, can be put right  
without contacting the Service Department.  
,Repair work to electrical equipment should only be carried out by a suitably  
qualified person in accordance with local and national safety regulations.  
Repairs and other work by unqualified persons could be dangerous. The  
manufacturer cannot be held liable for unauthorised work.  
General problems  
Problem  
Possible cause  
Remedy  
The tumble dryer fails to No obvious cause.  
start when switched on.  
Have you followed the  
switch-on procedure  
correctly (see “How to  
dry correctly”)?  
Is the plug correctly  
inserted in the socket  
and switched on?  
Is the door closed  
properly?  
Has the fuse or circuit  
breaker tripped?  
Items made of synthetic Synthetic fibres tend to  
fibres are charged with attract static charge.  
static electricity after  
Static charge can be  
reduced by adding a  
fabric conditioner to the  
final rinse in the washing  
machine or a fabric  
drying.  
conditioner sheet to the  
load in the dryer.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Problem solving guide  
Problem  
Possible cause  
Remedy  
There is a build up  
of fluff.  
Fluff is principally the result Fluff is collected by the fluff  
of friction when garments  
are being worn and  
filters and can be easily  
removed (see "Cleaning  
and Care").  
washed. Machine drying  
hardly causes any fluff to  
form and has been  
established by research  
institutes to have no effect  
on the lifetime of fabric.  
The laundry is not  
sufficiently dry.  
The load consisted of  
different fabrics.  
Finish drying using  
"Timed drying - Warm  
air".  
Select a more suitable  
drying programme next  
time (see "Programme  
chart").  
There are water  
A double filter system with Laundry being removed  
droplets at the upper dual insulation prevents fluff from the machine may  
edge of the drum  
aperture.  
from being deposited in the come into contact with  
condenser unit. This  
these water droplets, but  
they will dry off in a matter  
of minutes.  
insulation can lead to a  
build-up of condensation.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem solving guide  
Problem  
Possible cause  
Remedy  
The drying process Important: Before attempting to remedy one of the  
goes on too long or following causes, switch the dryer off and switch on again  
even switches off. to start the programme again.  
Ventilation to and from the  
dryer may be insufficient  
Open a door or window  
while the machine is in  
(e.g because it is installed in operation for increased air  
a small room). This has  
caused the temperature in  
the room to rise sharply.  
flow.  
The fluff filters are clogged  
up with fluff or were still wet  
when they were replaced.  
Remove any fluff.  
The fluff filters must be  
completely dry.  
The laundry has not been  
spun sufficiently.  
Make sure that your laundry  
is thoroughly spun at  
highest spin speed for the  
type of fabric.  
The tumble dryer has been Do not exceed the maximum  
overloaded.  
load for the programme  
selected.  
Metallic components, e.g.  
zips have prevented the  
dryer from registering the  
correct moisture level in the  
laundry.  
Close zips and fasten any  
hooks next time.  
If the problem occurs again,  
dry garments with long zips  
using "Timed drying - Warm  
air".  
Detergent residues, hair and Check the condenser unit  
fine fibres can block up the from time to time and clean  
condenser unit.  
it if necessary (see  
"Cleaning and Care").  
The vents below the door  
are blocked.  
Remove any objects that are  
blocking the vents.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem solving guide  
Problem  
Possible cause  
Remedy  
The condenser unit The inner cover of the  
Ensure that the condenser  
unit is positioned correctly  
and lock the cover.  
service panel will  
not shut.  
condenser unit has not  
been locked properly  
and/or the condenser unit  
has not been positioned  
correctly.  
Check the rubber seals.  
Water leaks from the Fluff has collected at the  
machine after the bottom of the condenser  
condenser unit has unit housing.  
Use a cloth to remove any  
fluff from the inside of the  
condenser unit housing.  
been cleaned.  
The interior drum  
lighting does not  
come on.  
The lighting switched off  
automatically.  
The lighting only comes on  
when the door is opened if  
the dryer is switched on. To  
save energy the lighting  
goes out after a while if the  
door is left open.  
The lamp needs changing. Change the lamp as  
described at the end of this  
section.  
The ring around the The lighting switched off  
programme selector automatically.  
does not light up.  
It lights up when drying is in  
progress and goes out  
shortly after the end of the  
programme to save energy.  
Check and fault indicator lamps  
Problem  
Possible cause  
Remedy  
The Anti-crease /  
Finish indicator  
lamp flashes while  
drying is in  
The programme selector  
was moved after the start original position and the  
of a programme. The  
programme continues to  
run as normal.  
Turn the selector back to the  
indicator lamp will go out.  
progress.  
The Locked  
The system lock is  
activated.  
If you wish to use the dryer,  
the system lock must be  
deactivated (see "Electronic  
system lock").  
indicator lamp  
flashes when the  
machine is switched  
on and the  
programme cannot  
be started.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Problem solving guide  
Problem  
Possible cause  
The fluff filters may be  
Remedy  
The Clean out  
airways lamp comes blocked.  
Remove any fluff (see  
"Cleaning and care").  
on.  
The condenser unit may be Please note that the  
blocked with fluff and  
detergent residues.  
condenser unit must be  
cleaned regularly (see  
"Cleaning and care").  
The check lamp will go out  
when the door is opened.  
The programme  
Possible causes and remedies are described above in  
stops and the Clean (The Clean out airways lamp comes on).  
out airways lamp  
flashes.  
There is no obvious cause. Switch off the dryer.  
Then switch the dryer  
back on and start the  
programme again.  
If the programme stops  
again and the Clean out  
airways lamp flashes, there  
is a fault. Contact the Miele  
Service Department.  
The Empty out  
container indicator  
lamp comes on.  
The condensed water  
container is full or there is  
kink in the drain hose.  
Empty out the  
condensed water  
container.  
Check the drain hose.  
Before starting a new  
programme, first switch  
the dryer off and then on  
again.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem solving guide  
Problem  
Possible cause  
Remedy  
The programme has  
stopped. The  
This is not a fault.  
Use the "Timed drying -  
Warm air" programme to  
dry individual items.  
The electronic unit has  
recognised that there is no  
laundry in the drum and  
Anti-crease/Finish  
lamp has come on in  
the sequence display  
and the buzzer is  
sounding.  
Before changing a  
cancelled the programme. programme: Open and  
close the drum door.  
Drying individual garments  
or items which are already  
dry can also cause the  
programme to be stopped.  
The programme has  
been interrupted. The  
indicator lamp for  
Hand iron or Machine  
iron is flashing, and  
the buzzer sounds.  
No obvious cause.  
Switch the dryer off and  
then on again.  
Then start the  
programme again.  
If the programme stops  
again and the fault  
message reappears there  
is a fault. Contact the  
Miele Service  
Department.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem solving guide  
To change the interior drum  
lamp  
^ To close the flap push it upwards and  
press it on the left and right until you  
hear it click into position.  
^ Open the door.  
The cover must be fixed securely, as  
otherwise moisture may seep in and  
cause a short circuit.  
Before changing the lamp,  
disconnect the machine from the  
mains power supply.  
You will find the interior lamp cover at  
the top of the drum aperture.  
^ Insert the opener under the side  
edge of the cover as illustrated.  
^ Turn your wrist to make the cover  
open downwards.  
The temperature resistant lamp should  
only be ordered from your Miele dealer  
or the Miele Spare Parts Department.  
The lamp must not exceed the  
maximum wattage quoted on the  
data plate and on the lamp cover.  
^ Replace the lamp.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Problem solving guide  
After sales service  
Repairs  
Appliance guarantee  
The appliance is guaranteed for a  
In the event of any faults which you  
cannot remedy yourself, please contact period of 1 year.  
– Your Miele Dealer or  
See the guarantee card supplied with  
the appliance for further details.  
– The nearest Miele Service  
Department (see back cover for  
address).  
Optional accessories  
Optional accessories for these dryers  
are available from your Miele Dealer or  
from the Miele Spare Parts Department.  
When contacting the Service  
Department, please quote the model  
and serial number of your appliance,  
both of which are shown on the data  
plate situated on the right hand side  
below the drum aperture.  
Please note that telephone calls may  
be monitored and recorded to  
improve our service.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Front view  
aSupply cable for electrical  
eService panel for condenser unit  
connection  
fFour height-adjustable screw feet  
bCondensed water container  
cControl panel  
gExternal drainage options (e.g. via  
wash basin, wash basin drain outlet,  
or gully).  
dDoor  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Installation site  
A building under kit* is required.  
,Make sure the dryer door can be  
opened without hindrance after  
installation.  
The machine lid is replaced by a  
coverplate which must be fitted by a  
suitably qualified person to ensure  
electrical safety.  
Transporting the machine to its  
installation site  
– When installing under a 900/910 mm  
high worktop a spacer kit* is  
required.  
When moving the machine you can  
hold it by the lid where it protrudes to  
the rear of the dryer.  
To manoeuvre the dryer out of its  
packing case to its installation site you  
will also need to hold it by the front feet.  
– The electrical socket must be  
located in an accessible position  
near the machine.  
* Available as an optional accessory  
from your Miele dealer or the Miele  
Spare Parts Department.  
Building under a continous worktop /  
in a row of kitchen units  
The building under kit is supplied with  
its own installation instructions.  
The dryer should not be installed  
next to a refrigerator or freezer. The  
warm air expelled from the rear of  
the dryer would increase the  
temperature around the  
refrigerator's/freezer's heat  
exchanger causing the compressor  
to run continuously.  
If it is not possible to install the dryer  
anywhere else, then the  
refrigerator/freezer must be sealed  
off from the dryer.  
N.B. When built under running times  
may be longer.  
Replacing the lid  
If the lid has been removed in order to  
fit a cover plate, ensure that, if the lid is  
replaced, it fits securely into the rear  
holders. Otherwise, it is not properly  
secure for transport.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Aligning the machine  
Room in which the dryer is located  
Air taken in for use in the drying  
process will be warm when it is  
expelled from the rear of the dryer. This  
expelled air heats up the air in the  
room. It is therefore very important to  
ensure that the room is adequately  
ventilated, particularly if the dryer is  
located in a small room. Otherwise  
running times and energy consumption  
could be increased.  
Washer - dryer stack  
The tumble dryer can also be  
combined with a Miele washing  
machine in a washer-dryer stack. To do  
this the appropriate stacking kit* (WTV)  
to match your washing machine is  
required.  
The machine must be perfectly level to  
ensure safe and proper operation.  
* Available as an optional accessory  
from your Miele dealer or the Miele  
Spare Parts Department.  
Stacking kits must be fitted by a  
suitably qualified fitter.  
Before moving the machine again  
(e.g. when moving house)  
After each use a small quantity of  
condensed water will collect in the area  
around the pump. This water can run  
out if the machine is tipped up when it  
is being moved. It is a good idea to run  
the Cool air programme for  
approximately 1 minute before moving  
the machine. Any remaining  
condensed water will then be fed into  
the condensed water container or out  
through the drain hose.  
^ The screw feet can be adjusted to  
compensate for any unevenness in  
the floor.  
,The ventilation gaps in the plinth  
must not be covered over as this  
would prevent a sufficient intake of  
air.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
External condensed water  
outlet  
From the back of the dryer at the  
bottom:  
When drying is in progress, condensed  
water is pumped into the condensed  
water container through the drain hose  
at the back of the dryer. The  
condensed water can also be drained  
off directly if the machine is installed  
near a sink, drain outlet etc. so that  
the condensed water container does  
not have to be emptied.  
The drain hose (approx. 2 m long) is  
stored in the dryer. It must be pulled  
out of the dryer to its full extent if  
condensed water is to be drained  
externally.  
^ Unclip the drain hose from holder (3).  
Maximum delivery head: 1 m.  
^ Then pull the drain hose completely  
out of the dryer towards the left (4)  
(See illustration).  
If it is not long enough, an extension  
hose is available as an optional  
accessory through your dealer or from  
the Miele Spare Parts Dept.  
,Important: do not let the drain  
hose become kinked as this could  
damage it.  
Pulling out the drain hose  
From the back of the dryer at the top:  
,If you want to drain the water off  
into a sink you will need to secure  
the hose carefully, e.g. by tying it to  
a tap to make sure it cannot slip  
during use. Otherwise there is a risk  
of overflowing water which could  
cause damage.  
Use the bow-shaped guide to prevent  
the drain hose from becoming kinked  
(see "Front view" illustration).  
^ Unclip the drain hose (1).  
^ Then pull it off holder (2).  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Connection to a sink drain outlet  
If this nut has a flat disc sealing it you  
should take the disc out first.  
Important: if this nut has a washer or  
seal in it this must not be removed!  
The drain hose can be connected  
directly to a sink drain outlet.  
^ Attach the end of the hose to adapter  
1.  
^ Use a screwdriver to tighten hose  
clip 3 up close to the nut.  
If you no longer wish to use an  
external condensed water outlet  
,Do not push the drain hose  
back into the dryer. Doing this could  
cause it to become kinked and  
damaged in the dryer.  
^ Remove the following from the back  
of the dryer at the bottom:  
Adapter 1 and hose clip 3 behind it.  
^ Loop the drain hose up.  
^ Use a suitable cable tie to secure the  
looped hose to the back of the dryer,  
or simply lay the looped hose behind  
the dryer.  
^ Attach the open end of the drain  
hose back onto the holder at the  
back of the dryer at the top (see  
holder 2 in "Pulling out the drain  
hose").  
^ Fit adapter 1 to the sink drain outlet  
using nut 2.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Electrical connection  
Electrical connection U.K.  
Electrical connection U.K.  
Non-rewireable plugs BS 1363  
All electrical work should be carried out  
only by a suitably qualified and  
If this machine is fitted with a  
competent person, in strict accordance non-rewireable plug and the socket  
with national and local safety  
regulations.  
outlets are not suitable for the plug  
supplied or if the existing plug needs to  
be replaced by a new one, the old plug  
will need to be cut off and an  
appropriate plug fitted. The fuse carrier  
and the fuse should be removed from  
the old plug and disposed of.  
Ensure power is not supplied to the  
machine while installation work is being  
carried out.  
The machine is supplied with a mains  
cable with moulded plug for connection  
to a 230-240V mains supply. The  
voltage, rated load and fuse rating  
are given on the data plate. Please  
ensure these match the household  
mains supply.  
The plug cut from the cable should then  
be disposed of and on no account be  
inserted into any socket elsewhere in  
the house (electric shock hazard).  
The fuse cover must be refitted when  
changing the fuse, and if the fuse cover  
is lost, the plug must not be used until a  
suitable replacement is obtained. The  
colour of the correct replacement cover  
is that of the coloured insert in the base  
of the plug, or the colour that is  
embossed in words on the base of the  
plug (as applicable to the design of  
plug fitted).  
Connection should be made via a fused  
plug and suitable switched socket  
which is easily accessible after  
installation.  
For extra safety it is advisable to install  
a residual current device (RCD), with a  
trip current of 30 mA (in accordance  
with DIN VDE 0664, VDE 0100, section  
739).  
Do not connect via an extension lead.  
Replacement fuses should be ASTA  
approved to BS 1362 and have the  
correct rating. Replacement fuses and  
fuse covers may be purchased from  
your local electrical supplier or Service  
agent.  
Important  
The wires in the mains lead are  
coloured in accordance with the  
following code:  
Green/yellow = earth  
Blue  
= neutral  
= live  
Brown  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Electrical connection  
If the colours of the wires in the mains  
lead of this machine do not correspond  
with the coloured markings identifying  
the terminals of your plug, proceed as  
follows:  
^ The wire which is coloured green and  
yellow must be connected to the  
terminal in the plug which is marked  
with the letter E or by the earth  
symbol z or coloured green, or  
green and yellow.  
^ The wire which is coloured blue must  
be connected to the terminal in the  
plug which is marked with the letter N  
or coloured black.  
^ The wire which is coloured brown  
must be connected to the terminal in  
the plug which is marked with the  
letter L or coloured red.  
WARNING: THIS APPLIANCE  
MUST BE EARTHED  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Consumption data  
Programme  
Capacity  
Final spin speed  
(in a domestic  
washing machine)  
Electricity  
consump-  
tion  
Drying time  
incl.  
cooling down  
time  
kg  
rpm  
kWh  
Minutes  
COTTONS  
Extra dry  
5.0  
1200  
1400  
1600  
3.25  
3.10  
2.85  
86  
83  
76  
Normal +  
5.0  
1200  
1400  
1600  
2.80  
2.65  
2.40  
76  
73  
66  
(1)  
Normal  
5.0  
5.0  
800 (70 % residual moisture)  
3.40  
89  
Normal  
1200  
1400  
1600  
2.65  
2.55  
2.25  
73  
70  
63  
(1)  
Hand iron  
Hand iron  
5.0  
5.0  
800 (70 % residual moisture)  
2.75  
72  
1200  
1400  
1600  
2.00  
1.90  
1.60  
55  
52  
46  
Machine iron  
5.0  
1200  
1400  
1600  
1.60  
1.50  
1.20  
46  
43  
36  
MINIMUM IRON  
(1)  
Normal  
2.5  
2.5  
1000 (50 % residual moisture)  
1000  
1.25  
1.10  
40  
36  
Hand iron  
Special care  
Woollens hand care  
Smoothing  
2.0  
2.5  
-
-
0.20  
0.30  
4
9
(1) EN 61121 test programme  
EN 61121 Standard testing  
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry  
with 70% residual moisture as per the above standard using the Normal Cottons  
programme without selecting any additional functions.  
Consumption data can vary from the nominal values given above depending  
on the size of the load, types of textiles, residual moisture levels after spinning,  
fluctuations in the electricity supply and any additional options selected.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Technical data  
Height  
85 cm (adjustable +0.7/- 0.7 cm)  
Height without lid  
Width  
82 cm  
59.5 cm  
58 cm  
Depth  
Depth with door open  
Weight  
106 cm  
54 kg  
Drum volume  
Maximum capacity  
100 litres  
5 kg dry weight  
Capacity of condensed  
water container  
approx. 3.5 litres  
1.60 m  
Length of connection cable  
Maximum delivery head  
Maximum drain hose length  
Voltage  
1 m  
3 m  
see data plate  
see data plate  
see data plate  
see data plate  
see "Consumption data"  
Radio/TV suppressed, VDE  
Rated load  
Fuse rating  
Lamp wattage  
Energy consumption  
Test certificates awarded  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programmable functions  
for changing  
standard settings  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programmable functions  
Increased drying level  
increased drying level is  
deactivated.  
The machine is designed to dry  
using as little energy as possible.  
However, if you require the laundry to  
be drier, it is possible to reduce the  
final moisture level in the COTTONS  
and MINIMUM IRON programmes.  
Note that programme durations will  
be longer if this option is activated.  
– If the Machine iron indicator lamp  
lights up, the increased drying level  
is activated.  
EPressing the START button switches  
between activating and deactivating  
increased drying.  
FSwitch the machine off with the I-On /  
0-Off button.  
The machine is supplied ex-works with  
this option switched off. It can be  
activated is wished.  
The setting you have selected is now  
stored in memory. You can change it  
again at any time.  
Programming and storing in memory  
To check:  
The programmable functions are  
activated with the help of the additional  
option buttons and the programme  
selector.  
^ Carry out steps A to D.  
If the indicator light for Machine iron  
lights up = Increased drying level is  
switched on  
does not light up = Increased drying  
level is switched off  
Before you begin, first ensure that:  
– The tumble dryer is switched off.  
– The door is closed.  
^ Switch the machine off with the I-On /  
0-Off button.  
– The programme selector is at Finish.  
APress the Low temperature and  
Buzzer buttons at the same time,  
keep them pressed in  
and ...  
The check is complete.  
B... switch the dryer on with the I-On /  
0-Off button.  
CThen release these buttons.  
– The Drying and Cool air sequence  
indicator lamps will flash.  
DTurn the programme selector to the  
COTTONS Extra dry position.  
– If the Machine iron sequence  
indicator does not light up, the  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programmable functions  
Memory function  
DTurn the programme selector to  
COTTONS Normal.  
The additional options selected  
previously for specific programmes  
are stored in the machine’s memory.  
– If the Machine iron sequence  
indicator does not light up, the  
Memory function is deactivated.  
The machine is supplied ex-works with  
the memory function switched off. It can  
be activated is wished.  
– If the Machine iron sequence  
indicator does light up, the Memory  
function is activated.  
EPressing the START button switches  
between activating and deactivating  
the Memory function.  
Programming and storing in memory  
The programmable functions are  
activated with the help of the additional  
option buttons and the programme  
selector.  
FSwitch the machine off with the I-On /  
0-Off button.  
The setting you have selected is now  
stored in memory. You can change it  
again at any time.  
Before you begin, first ensure that:  
– The tumble dryer is switched off.  
– The door is closed.  
To check:  
– The programme selector is at Finish.  
^ Carry out steps A to D.  
APress the Low temperature and  
Buzzer buttons at the same time,  
keep them pressed in  
and ...  
If the indicator light for Machine iron  
lights up = the Memory function is  
switched on  
does not light up = the Memory  
function is switched off  
B... switch the dryer on with the I-On /  
0-Off button.  
^ Switch the machine off with the I-On /  
0-Off button.  
CThen release these buttons.  
– The Drying and Cool air sequence  
indicator lamps will flash.  
The check is complete.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alteration rights reserved/4703  
M.-Nr. 05 993 030 / 01  
This paper consists of cellulose which has been bleached without the use of chlorine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Moxa Technologies Switch EDS 208 User Manual
MRV Communications Mouse TS5000 4U1 V User Manual
NAD Stereo Amplifier 163AV User Manual
NEC Turkey Fryer NDA 30016 003 User Manual
NETGEAR Network Card MA 101 User Manual
Nilfisk ALTO Vacuum Cleaner 580 P User Manual
Nokia Bluetooth Headset BH 304 User Manual
Nortel Networks Network Card MSC8101 ADS User Manual
Onkyo Stereo System HT SR800 User Manual
Panasonic Fax Machine KX FLB751AL User Manual