Miele Washer W 833 User Manual

Operating instructions

for washing machine

W 833

It is essential to read these oper-

ating instructions before installing or

using the machine, to avoid the risk

of accident, or damage to

the machine.

M.-Nr. 04 613 450

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the machine

1 Electric supply cable

5 Facia panel with controls

2 Inlet hose (able to withstand

6 Drum door

pressures up to 70 bar)

7 Panel for access to fluff filter, drain

3 Flexible drain hose (with detachable

pump and emergency door release

swivel elbow)

8 Four height adjustable feet

4 Detergent dispenser drawer

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the machine

Detergent dispenser drawer

Compartment i - Pre-wash

Compartment j - Main wash

Compartment p (with lid) -Conditioner

b “Door" pushbutton

e Spin speed selector

opens the drum door

f Programme sequence

c “I - ON / O - OFF” pushbutton

switches the machine on or off

or interrupts a programme

indicator and control lights

g Programme selector

d Pushbuttons for additional

options

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety Instructions

The electrical safety of this ma-

Read the operating instructions be-

fore using this machine for the first

time. They contain important infor-

mation about the safety, use and

maintenance of the machine. This

will avoid the risk of accidents and

damage to the machine.

Keep these operating instructions in

a safe place and ensure that new

users are familiar with the content.

Pass them on to any future owner of

the machine.

chine can only be guaranteed

when continuity is complete between

the machine and an effective earthing

system which complies with local and

national regulations. It is most import-

ant that this basic safety requirement is

regularly tested by a qualified electri-

cian.

The manufacturer cannot be held re-

sponsible for the consequences of an

inadequate earthing system.

For safety reasons do not operate

this appliance on an extension

cable. Danger of overheating.

Correct usage

Only use the washing machine to

wash items which are declared by

the manufacturer to be machine-wash-

able on the wash-care label.

Any other applications may be dan-

gerous. The manufacturer is not liable

for damage resulting from improper

use or operation.

The machine is built in accordance

with current safety requirements.

Unauthorised repairs could result in un-

foreseen dangers for the user, for

which the manufacturer cannot accept

responsibility. Repairs should only be

undertaken by a Miele approved engin-

eer.

This appliance should not be oper-

ated by children. Supervise its use

by the elderly or infirm.

The machine is only completely iso-

lated from the electricity supply

when:

– it is switched off at the wall socket

and the plug is withdrawn, or

Technical safety

Before setting up the machine,

check it for any externally visible

damage. Do not install and use a dam-

aged machine.

– it is switched off at the mains, or

– the mains fuse is withdrawn.

Before connecting the machine, en-

sure that the connection data on

the data plate (fusing, voltage and fre-

quency) matches the mains electricity

supply. If in any doubt, consult a quali-

fied electrician.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety Instructions

The best materials are used in the

manufacture of this machine, and

Before using the machine for the

first time, check that the transit fit-

every care is taken to check all parts.

However, with time, deterioration of

parts can occur, especially with such

components as hoses, giving rise to

leaks. This should be borne in mind if

operating the machine without supervi-

sion. Check the hose regularly for signs

of wear, and change in good time, to

avoid leaks and subsequent damage.

ting at the rear of the machine has

been removed (see section on “Installa-

tion”). During spinning, a transit fitting

which is still in place may result in dam-

age to both the machine and adjacent

furniture or appliances.

Turn off the stopcock if the ma-

chine will be left for any length of

time (e.g. holiday), especially if there is

no floor drain (gully) in the immediate vi-

cinity.

Faulty components must only be

exchanged for Miele original spare

parts. Only when these parts are fitted

can the safety standards of the ma-

chine be guaranteed.

Flooding danger.

If hooking the drain hose into a

wash basin, check that the water can

drain off quickly enough to prevent the

sink from overflowing.

Use

Make sure the drain hose is secure, so

that the force of the water flowing out of

the hose does not dislodge it. Other-

wise this will result in flooding.

Do not install your washing ma-

chine in rooms where tempera-

tures below freezing may occur.

Frozen hoses may burst under press-

ure. The reliability of the electronic con-

trol system may be impaired at tem-

peratures below freezing point.

Take care to ensure that foreign ob-

jects (e.g. nails, needles, coins,

paper clips, etc.) do not find their way

into the machine with the washing (e.g.

in pockets). Foreign objects can dam-

age components of the machine, which

in turn can result in damage to the

washing.

In countries where there are areas

which may be subject to infesta-

tion by cockroaches or other vermin,

pay particular attention to keeping the

appliance and its surroundings in a

clean condition at all times. Any dam-

age which may be caused by cock-

roaches or other vermin will not be

covered by the appliance guarantee.

Download from Www.Somanuals.com. All Manuals Search And Download.

Warning and Safety Instructions

If the correct amount of detergent

Always make sure the drum is sta-

tionary before reaching in to

remove washing. Reaching into a mov-

is dispensed, the machine should

not need to be descaled. If, however,

you do wish to descale the machine

only use proprietary non-corrosive de-

scaling agents and strictly observe the

instructions. Consult the Miele Cus-

tomer Service Department.

ing drum is extremely dangerous.

Accessories

Accessory parts may only be fitted

when expressly approved by

Textiles which have been pre-

treated in solvent based cleaning

agents must be thoroughly rinsed in

clean water before being washed in the

machine.

Miele. If other parts are used, guaran-

tee, performance and product liability

claims may be invalidated.

Disposal of your old machine

Never use solvent based cleaning

agents in this machine, as this may

result in damage to component parts

and create toxic fumes. Such deter-

gents also pose a fire and explosion ha-

zard.

Before discarding an old machine

unplug it. Render the plug useless.

Cut off the cable directly behind the ap-

pliance to prevent misuse.

Only use dyes specified by the

manufacturer as being suitable for

use in a washing machine. Always ob-

serve the manufacturer’s instructions

carefully.

Dye removers may contain sulphur

compounds which cause damage

such as corrosion to the machines. Do

not use dye removers in this machine.

For machines with a ’porthole’

door, remember that the porthole

glass will be hot when washing at very

high temperatures. Do not let children

touch it during a hot wash programme.

Download from Www.Somanuals.com. All Manuals Search And Download.

Help to protect our environment

Disposal of the packing

material

The transport and protective packing is

mostly manufactured from the following

recycled or re-useable materials:

Disposal of your old machine

Old machines may contain material

which can be reclaimed or recycled.

Please contact your dealer, your local

waste collection centre or scrap mer-

chant about potential recycling

schemes.

– corrugated paper/card

– polystyrene - CFC-free

– untreated surplus wood

Ensure that the machine presents no

danger to children while being stored

for disposal.

– chipboard, contains no phenolic

resins

See the appropriate section in the

Warning and Safety instructions.

– polyethylene foil (PE)

– packaging straps: polyropylene (PP)

Rather than just throwing these ma-

terials away, please take them to the

nearest local authority collection point

for specific waste.

Download from Www.Somanuals.com. All Manuals Search And Download.

Washing environmentally and economically

Caring for the environment means sav-

ing water, energy and detergent when

washing but without compromising on

results.

Economy tips

To help you wash most economically,

remember the following tips:

– The automatic load control facility

allows you to wash individual loads

of between 1 and 5 kg. Ideally wash

with the maximum load specified for

each programme. This uses the en-

ergy to the best advantage.

The key to a good wash result is finding

the best combination of amount of

detergent, temperature, length of pro-

gramme and the machine’s technology.

If necessary, some programmes take

longer to achieve this effect. With the

"Hydromatic" system, the drum can re-

volve at different speeds. Longer and

slower action together with pauses for

steeping, work towards a good result.

– Only use the correct amount of deter-

gent required for the water hardness

level in your area, according to the

detergent manufacturer’s recommen-

dations.

The automatic load control facility en-

sures the correct water level for the

type of fabric and laundry load being

washed. Sometimes it even appears

that there is no water in the drum.

– If washing is not heavily stained, se-

lect a lower temperature setting than

indicated on the wash care label but

do not additionally select "Short".

– Use the "Short wash" option for wash-

ing that is only very lightly soiled, but

do not additionally reduce the tem-

perature.

Normally, main wash is sufficient for a

clean result, so a pre-wash is not auto-

matically included in the programmes.

If it is wanted, a simple press on the

pre-wash selector includes it.

– Using the additional "Soak" option

allows you to reduce the tempera-

ture used in the main wash.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Flush out any residual test

Water hardness reminder

water still in the machine as

follows:

The amount of detergent will depend

on various factors including the

water hardness level in your area.

The dial located in the detergent dis-

penser box can be turned to the rele-

vant setting as a water hardness re-

minder, (using 1 = soft, 4 = very

hard).

Do not load the machine.

Add a little detergent to compart-

ment j.

Switch on the machine.

Press the “Short wash” selector.

Select the “COTTONS 60°C” pro-

gramme.

This operation will flush out any

residues.

Use the spatula supplied with the

machine. It is located at the rear of

the dispenser drawer.

If you do not know how hard the water

is in your catchment area, please con-

tact your local water authority.

Download from Www.Somanuals.com. All Manuals Search And Download.

Brief guide to correct washing

The headings numbered (1,2,3,...)

eral times before being included in a

mixed load.

offer a brief step by step guide to the

operating sequence.

Delicate textiles should be washed sep-

arately in a delicates programme.

Before washing

1 Prepare the wash load

Only wash textiles made from wool or

wool mixtures if the textile care label

states that they are suitable for ma-

chine washing.

Pre-treating the washing

Badly soiled areas, e.g. collars and

cuffs, and water soluble stains can be

pre-treated with bar soap, liquid deter-

gent or detergent mixed into a solution

or paste.

With particularly stubborn stains ask

your Dry Cleaner for advice.

Do not use solvent based cleaning

agents in this machine.

2 Open the door by pressing the door

button

Empty all pockets.

Foreign objects (e.g. nails, coins,

paper clips etc) can cause damage

to textiles and components in the

machine.

Sort the washing

Most textiles have a care label in the

collar or side seam. Sort the washing

by care label symbols. (See Symbols

chart). Only wash items in this machine

which are declared by the manufac-

turer as being machine washable on

the textile care label.

Dark textiles often contain excess dye

and should be washed separately sev-

Download from Www.Somanuals.com. All Manuals Search And Download.

Brief guide to correct washing

3Load the drum

4 Close the drum door.

Make sure no items of washing are

caught between the drum door and

the door seal.

Unfold washing and load loosely in the

drum. To achieve best results it is advis-

able to make up mixed loads consist-

ing of both large and small items.

This improves the washing effect and

helps distribute the load evenly during

spin.

5Turn on the stopcock

(if it is not already on)

6 Add detergent.

Overloading reduces the wash result

and causes more creasing.

See Section on Detergent for details.

To start a programme

1 Turn the programme selector

Please note maximum load weights:

COTTONS . . . . . . . . . . . . . . . . . . 5.0 kg

to “Finish/Start”.

MINIMUM IRON. . . . . . . . . . . . . . 2.5 kg

DELICATES/SYNTHETICS . . . . . 1.0 kg

WOOL . . . . . . . . . . . . . . . . . . . . . 1.0 kg

QUICK WASH 40°C . . . . . . . . . . . 2.5 kg

2Press the “I-ON / O-OFF button.

3 Press buttons for additional

options if required

4 Select the spin speed.

(See Section on Additional options).

Curtains:

Remove lead weights and strips or

place in a laundry bag.

5 Turn the programme selector to

the wash programme desired.

Any loose wiring in bras etc.,should be

removed or sewn in.

The programme selector can be turned

to the left or the right.

Woollens, knitted garments, T-shirts

etc:

Turn inside out, if the manufacturer rec-

ommends it.

Download from Www.Somanuals.com. All Manuals Search And Download.

Brief guide to correct washing

7 Close the drum door

After washing

Otherwise there is a danger of objects

being placed inadvertently in the drum.

If these remained unnoticed and were

washed in the next load, they could

damage the washing.

1 Turn the programme selector

to “Finish/Start”.

2 Press the “Door” button.

Only remove washing from the ma-

chine once the drum has stopped

turning, otherwise you may seri-

ously injure yourself.

3 Press the I-ON / O-OFF button.

4 Remove the washing.

Make sure the drum is empty. Items

left behind could shrink or colour

run in the next wash.

5Check the folds in the door seal

for buttons etc.

6 Turn off the stop cock at the end

of the day

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing the programme sequence

Stopping a programme

To omit a programme stage.

Turn the programme selector to “Fin-

ish/Start”.

Turn the programme selector to “Fin-

ish/Start”

As soon as the programme sequence

light for the stage at which the pro-

gramme should continue starts flashing:

Interrupting a programme

Press the “I-ON/0-OFF” buttton.

To continue the programme, switch the

machine back on.

Turn the programme selector switch

to the appropriate programme within

3 seconds.

Changing an incorrectly selected pro-

gramme:

Turn the programme selector to “Fin-

ish/Start”.

A new programme can be selected

when only the “ON” indicator light is

still on.

Changing a programme which has

been locked, see Section on Activating

programmable functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adding or removing washing

Washing can be added or removed

MINIMUM IRON and WOOLLENS

after the programme has already

started, when using the following pro-

grammes:

The door can be opened during the fol-

lowing programme stage:

– Main wash

– COTTONS

– MINIMUM IRON

– QUICK WASH 40°C

– WOOLLENS

– Starch

Washing cannot be added or removed

later if the following additional options

or programmable functions have been

selected:

Press the “Door” button in and hold it

until the door springs open.

– “Water plus” (the water level is in-

creased)

Add or remove items of washing.

– Programme lock (e.g. to prevent

children from opening the door dur-

ing the wash cycles).

Press any option buttons that had

previously been selected.

Shut the door.

COTTONS and QUICK WASH 40°C

The door can be opened in the follow-

ing programme stages:

– Main wash

– Rinses

Please note that the door can only be

opened when the suds temperature is

less than 55°C.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adding detergent

All modern detergents produced for

...too much results in the following:

automatic washing machines are suit-

able, including liquid, compact (con-

centrated) and special application

detergents. Use dispensing aids, e.g.

balls, if these are supplied with the

detergent. Woollens and knitwear con-

taining wool mixtures should be

washed using a detergent specifically

designed for washing woollens.

Amounts of detergent are recom-

mended on the packaging. The right

amount to dispense will depend on the

following:

– Excessive foam.

– Low level of agitation.

– Poor washing and rinsing results.

Water is taken in through compartment

i in the pre-wash.

Water is taken in through compartment

j in the main wash. If the capacity of

compartment j is insufficient for the

amount of detergent needed (e.g. in

very hard water areas), the Customer

Service Engineer can adjust the ma-

chine so that water and detergent can

– The quantity of the washing.

– The water hardness level (check with also be taken into the main wash

your local water supplier).

through compartment i.

– The level of soiling.

Water Softeners

Water Hardness

A water softener can be used to cut

down on the use of detergents in water

hardness ranges II-IV. Dispense ac-

cording to the amount specified on the

packaging. First add detergent and

then the water softener.

Hardness

range

Type of

water

(hardness)

Total

°dH

hardness (German)

(mg/l)

soft

medium

hard

0 - 130

130 - 250

250 - 380

over 380

0° - 7°

7° - 14°

14° - 21°

over 21°

III

very hard

Use a quantity of detergent as for soft

water.

It is important to dispense the

correct amount, because...

If you wash using several components

(e.g. special application detergents),

we recommend dispensing the agents

into compartment j in the following

order:

...too little has the following results:

– The washing will not be properly

clean and will in time become grey

and hard to the touch.

1. Detergent

2. Water softener

3. Stain salts

– Greasy particles cling to the washing.

– Lime deposits on the heater ele-

ments.

This way the agents are distributed

more efficiently.

Download from Www.Somanuals.com. All Manuals Search And Download.

Fabric conditioners/starch formulations

Fabric conditioners/Texturisers Starch / liquid starch

Fabric conditioners make garments

soft and fluffy to handle and help pre-

vent static cling when tumble drying.

Dispense according to the manufac-

turer’s instructions.

Prepare and dispense the starch sol-

ution in accordance with the manu-

facturer’s instructions.

Add to compartment i.

Select the spin speed.

Texturisers are synthetic starch formula-

tions and give body to items e.g. shirts,

tablecloths and bed linen.

Turn the programme selector to

“Starch”.

Open the lid of compartment p.

– The “Soak / Pre-wash” indicator will

light up.

– If the washing is not be be spun at

the end of the programme after

starching, turn the spin speed selec-

tor to “without final spin”. Water will

be drained away at the end of the

starch stage.

– If the washing is to be steeped in

water after the starch stage (to less-

en creasing), turn the spin speed se-

lector to “Rinse hold”.

To continue:

Select a spin speed.

Add fabric conditioner, but do not

exceed the max. level mark.

Close the compartment lid and push

the drawer back in.

– The conditioner is automatically dis-

pensed in the last rinse. At the end

of the programme a small amount of

water remains in the fabric condi-

tioner compartment p.

– If preferred, turn the spin speed se-

lector to "Rinse hold" to allow the

load to steep in the fabric condi-

tioner / retexturiser.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme selection

Programme

Fabric

Temperature

range

cottons and linen fabrics eg bedlinen, table linen,

towelling, jeans, T-shirts and nappies.

95°C bis 30°C

COTTONS

9876

(60°C) white nylon white polyester fabrics,

(50°C) coloured nylon, polyester, cotton and viscose

fabrics with special finishes, acrylic cotton fabrics,

coloured polyester / cotton fabrics

60°C to 30°C

MINIMUM IRON

4321

(40° / 30°C) minimum iron fabrics not washable at

higher temperatures, (60 - 30°C).

Acrylics acetate and triacetate, socks and stockings in

man-made fibres (not wool or wool blends),

60°C to cold

DELICATES

Curtains declared machine-washable by the

manufacturer (pre-wash probably advisable)

30°C to cold

40°C to cold

Programme for machine-washable wool fabrics bearing

the machine-washable care label

(there is not a pre-wash option)

WOOLLENS

(See Care Symbol Chart)

Very lightly soiled fabrics

Not suitable for Delicates

40°C

cold

QUICKWASH 40°C

Table cloths, napkins, overalls, uniforms.

Starch

Articles which can be spun, eg handwashed items

Spin

For use when the cycle stops at “Rinse hold” and the

washing is not to be spun

Drain

Articles which should be washed by hand and only

rinsed and spun in the machine.

cold

SEPARATE RINSE

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme selection

Max. load

Additional options

Notes

5 kg

– Soak

with heavily soiled items select “Soak” or

“Pre-wash”

– Pre-wash

– Water plus

– Short wash

2,5 kg

1 kg

– Soak

with heavily soiled items select “Soak” or

“Pre-wash”

– Pre-wash

– Water plus

– Short wash

for lightly soiled items select Short wash"

– Soak

– Pre-wash

– Short wash

Use the Wool programme for textiles with

wool content.

If “cold” is selected for the temperature,

the water is warmed to 24°C. This helps

the effect of the detergent.

For shorter programmes use Delicates +

Short wash and not “QUICKWASH 40°C”

Fill the drum

loosely 1/2 to 3/4 – Pre-wash

– Soak

Dust in curtains usually makes pre-wash

advisable

full

– Short

1 kg

If “cold” is selected for the temperature,

the water is warmed to 24°C. This helps

the effect of the detergent

2,5 kg

– Water plus

Add less detergent (half load)

5 kg

The washing should be washed but not

treated with fabric conditioner.

5 kg

See Section on Additional options for more details, and also Section on Programmable functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme sequence

COTTONS

MINIMUM IRON

DELICATES

Soak

optional

Pre-wash

optional

Main wash

Top-up rinse

from 75°C

–

Graduated rinsing

No. of rinses – normal

– part load

from 50°C

3 oder 4¹⁾

– short wash

Rinse & interim spin (rpm)

Final spin (rpm)

Anti-crease spin & loosen

Rinse hold

max. 1000

max. 1200

max. 30 mins

optional

normal

max. 500

max. 900

max. 30 mins

optional

normal

–

max. 600

max. 30 mins

optional

gentle action

Without final spin

Wash rhythm

Water level – Wash

– Rinse

low ²⁾

high

low ²⁾

medium ²⁾

Notes:

programme section available

–

Programme section not available

¹⁾A 4th rinse automatically switches in if there is too much foam in the drum, or if a spin speed lower

than 800 rpm has been selected.

²⁾Increasing the water level:

The water level can be increased from a low level to a higher level by pressing the “Water plus” button.

³⁾Top-up rinse:

Additional water flows into the drum, and the suds are cooled slightly. Hot water might damage plastic

drain pipes.

Graduated rinsing:

The suds are cooled at the end of the wash cycle by water flowing in and being pumped away at inter-

vals. This minimises the danger of creasing, by avoiding sudden temperature changes.

WOOLLENS:

Wool is susceptible to damage from movement when it is wet. Drum movement times during the pro-

gramme are shorter, and the drum rotates more slowly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programme sequence

WOOLLENS

QUICKWASH

40°C

Starch

Spin

Separate rinse

–

max. 500

max. 1200

max. 30 min

optional

normal

–

max. 900

–

max. 900

–

max. 1200

max. 30 min

optional

normal

max. 1200

max. 30 min

optional

Wool

–

optional

–

medium

high

low ²⁾

medium

low

–

high

Interim spin:

There is a spin between the rinses.

Final spin:

The maximum spin speed according to the programme is held constant for a fixed period of time. In

the programmes MINIMUM IRON, WOOL and Separate Rinse the spin speed is automatically limited

to 900 rpm and in the DELICATES programme to 600 rpm, even if the selector has been set to a

higher spin speed. A lower speed can be selected.

Anti-crease action:

Guards against the tendency for creases to set in when fabrics have been left in water for a long time.

There is drum movement twice a minute.

Download from Www.Somanuals.com. All Manuals Search And Download.

Care symbols

Hand wash

do not wash

Washing

Cottons 95°C

Cottons 60°C

ABC dry clean

do not dry clean

Cottons 40°C

Minimum iron 60°C

Minimum iron 40°C

Minimum iron 30°C

Delicates 40°C

Delicates 30°C

suitable for chlorine bleach

do not use chlorine bleach

Tumble dry

at normal temperature

at low temperature

do not tumble dry

Machine washable woollens

Ironing

Use the special ’Wool’ programme,

and only wash textiles bearing the

label shown here:

hot iron

medium hot iron

cool iron

do not iron

N.B. If you have any textiles with the

older wash care labels, select a pro-

gramme according to the label below.

Cottons

[:\]

This symbol is registered by the IWS

(International Wool Secretariat)

Minimum iron ?;\

Delicates ={

Woollens

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional options

Each of the following buttons can be

The following options are additionally

available for certain wash programmes:

pressed in to give an additional option.

“Soak”

– For heavily soiled and stained items

with dried on stains, or ones which

can be bleached out, (e.g. blood,

fats and oils, cocoa).

– Soak duration: 2 hours.

When the “Door” button is pushed in,

all the other buttons spring out again,

and the additional options are can-

celled.

Amount of detergent for "Soak"

The amount of detergent recom-

mended by the detergent manufac-

turers should be distributed according

to to the wash programme which is to

be run after the “Soak” process.

– Programmes without pre-wash:

Add the total amount of detergent to

compartment j or directly into the

drum on top of the laundry.

– Programmes with pre-wash:

1/4 of the detergent should be added

to compartment i for the soak and

pre-wash, and 3/4 added to compart-

ment j for the main wash.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional options

“With pre-wash”

Spin

– For heavily soiled and stained items.

The final spin speed is selected by turn-

ing the spin speed selector to the set-

ting required, but also depends on the

basic wash programme chosen.

“Water plus”

– This is recommended for particularly

delicate fabrics, and

“Without final spin”

– if more water is required for dispens-

ing the detergent.

Interim rinse and spin is carried out in

the relevant programmes.

– the water level increases in all sec-

tions of the programmes COTTONS,

MINIMUM IRON and QUICK WASH

40°C.

Washing is not spun after the final

rinse, but the water is drained away,

and the machine goes straight into the

anti-crease stage.

“Short wash”

“Rinse hold”

– The length of the main wash is short-

ened for lightly soiled items. An addi-

tional reduction in temperature is not

recommended as this may lead to

poorer wash results.

Interim rinse and spin is carried out in

the relevant programmes.

At the end of the final rinse the washing

remains suspended in water.

This helps to reduce the possibility of

creasing, if the washing is left for some

time before being taken out of the ma-

chine.

– In the COTTONS and MINIMUM

IRON programmes only two rinse

cycles are carried out at high water

level.

To continue the programme:

Turn the spin speed selector to the re-

quired setting.

The maximum spin speed is automati-

cally limited according to the basic

wash programme chosen.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Cleaning the washing machine

Clean the casing with a mild non-ab-

rasive detergent or soap and water.

Wipe dry with a soft cloth.

Clean the facia panel with a damp

cloth and dry with a soft cloth.

The drum can be cleaned using a

suitable proprietary stainless steel

cleaner.

Do not use abrasive cleaners, or

glass or all purpose cleaners.

These might cause damage to the

plastic surfaces because of the

chemicals they contain.

Clean the detergent dispenser and

conditioner dispenser compart-

ments. Regularly remove any deter-

gent residues.

Detergent dispenser drawer

Pull out the detergent dispenser

drawer until a resistance is felt.

Remove the suction tube from com-

partment p, wash under running

warm water and put back.

Press down the red release knob

and at the same time pull the drawer

right out of the machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Cleaning the fluff filter and

pump

Check the fluff filter initially after 3 - 4

washes to ascertain how often it is

likely to require cleaning.

With normal cleaning approx. 2 litres of

water run out.

If the drain outlet is clogged, more

water will be retained in the machine

(up to 25 litres).

Caution: if laundry has been

washed at a high temperature,

water draining out of the machine

will still be hot!

Open the flap

Place a dish under the drain fixture.

Take the (yellow) filter flap opener from

behind the detergent drawer facia

panel, (see illustration above).

Turn the fluff filter lid round 2 - 3

times. Do not take it right out.

With large volumes of water when the

dish is full, screw the fluff filter back

into position and empty the dish before

repeating the procedure.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Once the flow of water ceases,

remove the fluff filter completely and

clean it.

Clean the inside of the fluff filter hous-

ing.

Remove any deposits of lime scale and

Remove any foreign bodies (e.g. but- detergent or foreign bodies from the

tons, coins, etc.) and fluff.

thread of the filter housing and filter unit

(as these objects can cause a leakage

of water).

Turn the impeller by hand to check

that it is free to rotate. Any foreign ob-

jects causing an obstruction should

be removed.

Put the fluff filter back and screw it in

firmly.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Inspect the inlet hose which is sub-

jected to high pressure while the ma-

chine is in operation. The hose should

be replaced if there are small cracks in

the surface, or if it has been otherwise

damaged.

To clean the water inlet filters

The washing machine has two filters to

protect the inlet valves. These filters

should be checked every 6 months or

so, or more often if there are frequent in-

terruptions to the water supply.

If replacing the inlet hose only use a

hose able to withstand pressure up to

70 bar. Miele’s own hoses meet this re-

quirement.

To clean the filter in the union in the

open end of the inlet hose:

First turn off the stopcock.

To clean the filter in the water inlet

valve:

Unscrew the threaded union con-

necting the free end of the inlet hose

to the stopcock.

Remove the rubber seal from the re-

cess.

Using pliers, carefully loosen the

ribbed plastic nut on the inlet valve,

and unscrew.

Use water pump pliers to withdraw

the plastic filter by the bar (see illus-

tration). Clean, put back and secure.

Using pointed pliers, take hold of the

plastic filter bar, remove the filter and

clean.

Put the filter and seal back in the

reverse order and reconnect the

hose. Turn on the stopcock and

check the connection is watertight.

The two filters must be put back in

place after cleaning.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

Repair work to electrical appliances should only be carried out by a suitably

qualified person in accordance with local and national regulations.

Unauthorised repairs could be dangerous.

What to do if . . .

Cause . . .

Remedy . . .

There is no power.

The “ON” indicator light has not

lit up.

Check that:

. . . the programme does

not begin:

– the door is properly closed.

– the plug is plugged in, and

the socket switch is on.

– the fuse or circuit breaker

has not tripped.

There is power and the “ON”

indicator is lit up, but the

programme selector has not

been turned to the “Finish /

Start” position.

– Turn the programme selector

to the “Finish / Start” position.

– Select a programme.

The water inlet is blocked,

but the programme has run

normally.

– The stopcock is not opened

. . . the “Check water inlet /

outlet indicator light is flash-

ing:

far enough.

– The inlet hose is kinked.

– The water pressure is too

low. Call the Service dept.

The water inlet system is

blocked.

– Turn the programme selector

to “Finish / Start”.

The “Finish” light is on in the

display sequence, but the load

in the machine has not been

washed.

– Open the stopcock.

– Select a programme.

The water outlet is blocked.

– Clean the fluff filter and drain

pump.

– Has the drain pump been

fitted too high? (max, drain

head 1 metre).

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

What to do if, . . .

Cause . . .

Remedy . . .

There is a fault.

. . . one of the following

lights is flashing:

Start the programme again. If

the light starts flashing again,

call the Service dept.

– “Soak/Pre-wash”

– “Main wash”

There is a fault.

. . . the “Rinses/Rinse hold”

light flashes quickly?

The spin speed selector has

been set to “Rinse hold”.

Select a spin speed or “Without

final spin”.

. . . the “Rinses/Rinse hold”

light flashes slowly?

The final spin has not taken

place. The machine detected

an imbalance.

– Loosen the laundry load.

– Turn the programme selector

to “Spin”.

. . . the “Drain/Final spin”

light is flashing:

– The spin speed appropriate

for the programme should be

selected.

Programme locking is activated. Reselect the programme

. . . the “ON” indicator light

is flashing:

There was an attempt to alter

the programme.

originally chosen.

The spin speed selected was

too low.

Select a higher spin speed next

time.

. . . the washing is not spun

satisfactorily:

The load was not distributed

sufficiently evenly in the drum.

Laundry was spun at a reduced

speed to protect the machine.

Mix large and small items in a

load to avoid imbalance.

The fluff filter is clogged.

Clean the fluff filter.

The four feet are not resting

evenly on the floor.

Level the machine (See Section

on Installation).

. . . the machine shakes

during the spin cycle:

The filters in the water inlet

system are blocked.

Clean the water inlet filters.

. . . in spite of adequate

water supply the water flows

slowly into the machine:

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

What to do if . . .

Cause . . .

Remedy . . .

The appliance is not plugged in Put the plug in the socket.

to the electricity supply.

. . . the drum door cannot be

opened.

Power cut

See “What to do if” - (1st

Section) on how to open the

door.

The door was not correctly

engaged.

Please press hard against the

lock side of the drum door and

then press the “Door” button.

There is still water in the drum.

– Select the “Drain”

programme for the water to

be pumped out.

– Open the drum door

The suds temperature is higher

than 55°C.

The water supply pressure is

too low.

– Clean the water inlet filter.

– It may be useful to select

“Water plus”.

. . . large residues of deter-

gent remain in the dispenser

drawer:

Washing powder used with

Pour washing powder into the

water softener tends to become dispenser before adding the

sticky.

water softener.

The dispenser drawer was not

pushed right in when the

conditioner was being flushed

in.

. . . fabric conditioner is not

completely dispensed or

water remains in the p com-

partment:

The siphon tube is either

incorrectly positioned or

clogged.

Clean the siphon tube.

Too much detergent was used.

Use only a suitable low-lather

detergent at the appropriate

temperature.

– Follow recommendations on

. . . there is an excessive

build-up of foam:

the packet.

– Take the water hardness

level into account.

– Use less detergent for lightly

soiled or small loads.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

What to do if . . .

Cause . . .

Remedy . . .

Not enough detergent has been – Use a descaling agent which

. . . lime deposits appear on

the drum surface:

used.

must be stated by the

manufacturer to be suitable

for use in washing machines.

– Use the correct amount of

detergent to cope with the

water hardness.

Insufficient amounts of

– Either add more detergent,

. . . grey, greasy particles

cling to washed laundry:

detergent were used to break

down the particles of grease in

heavily soiled laundry.

or use liquid detergent.

– Before washing the next load

run a COTTONS 60°C

programme with liquid

detergent but without a load

to clean the machine.

The detergent contained

compounds (zeolites) to aid

water softening which are not

soluble in water. These have

ended up on the textiles.

– Use detergents containing

no zeolites to re-wash the

load and in the future. Liquid

detergents usually contain no

zeolites.

. . . there are white residues

which look like powder deter-

gent on the washing:

– Try and brush off the

residues with a soft brush.

Liquid detergents do not usually – Use a general purpose

. . . liquid detergent does not

give the desired result:

remove stains such as fruit

juice, tea, coffee, wine etc.

washing powder containing a

bleaching agent, (check first

with the care label).

– Pour stain remover (salts)

into the dispenser drawer

compartment j

Put the liquid detergent into a

dispenser ball.

– Never put stain salts and

liquid detergent together in

the dispenser drawer.

These noises occur at the end

of a pump sequence as a

normal part of the operation.

They are not a fault.

. . . the pump makes strange

noises.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

Opening the drum door in the

event of a power failure

To check water pressure

Place a bucket under the stopcock.

Turn on the stopcock.

Switch off the washing machine.

Open the drain pump/fluff filter panel

and drain off any water as described

in the Section on Cleaning and care.

If 5 litres of water flow into the bucket in

15 seconds the water pressure is cor-

rect.

Electric socket

– If there is any doubt about the elec-

tricity supply socket, consult a quali-

fied electrician.

Pull the ring of the door mechanism

downwards, the door will open.

Always make sure that the drum is sta-

tionary before reaching in to remove

washing. Reaching into a moving drum

is extremely dangerous.

Download from Www.Somanuals.com. All Manuals Search And Download.

After sales service

In the event of any faults which you can

not remedy yourself, please contact:

Future updates

The indicator light marked PC is

reserved for the service engineer, for

updates in future years to your machine.

– Your Miele Dealer or

– Your nearest Miele Service depart-

ment.

(see back cover for the address).

When contacting the Service Depart-

ment, please quote the Model and Ser-

ial nos. of your appliance, both of

which are shown on the data plate

visible when the door is opened above

the porthole glass.

When for example technological devel-

opments offer advanced modifications

to your existing programme cycles, a

service engineer will be able to input

these into your machine controls.

Miele will provide information when

such possibilities become available.

Example:

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Installation surface

Ensure that the machine feet and the

floor are dry to prevent the machine

from slipping during the spin cycle.

Experience has shown that a concrete

floor is the most suitable installation sur-

face for a washing machine. Concrete

floors are far less prone to vibration dur-

ing the spin cycle than wooden floor-

boards or a surface with "soft" proper-

ties.

Removing the transit fitting

Please note the following points:

The machine must be level and se-

curely positioned.

To avoid vibrations during spinning,

the machine should not be installed

on soft floor coverings.

If installation must be on a wooden

joist floor, we recommend the use of

a plywood base at least 30 mm thick

and 59 x 52 cm wide. Ideally, the

base should be large enough to

span several joists and should be

bolted to the joists and not only to

the floorboards. Check for the

Using a pipe wrench turn the left-

hand transit bar 90°.

presence of pipes and cables first.

The most stable part of a floor is

usually in the corner.

If the machine is installed on a

raised plinth, it must be secured

against slippage during spin using

retaining clips (available from the

Miele Spare Parts Dept).

Installation

Turn the right-hand transit bar 90°.

Lift the machine from its packaging

base and move it to its site. Please

note:

Do not lift the machine by the drum

door.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Withdraw the two bars together with

the support plate.

Plug the two holes with the plastic

caps supplied.

The machine should not be moved with-

out the transit fitting in place.

The transit fitting should be stored

in a safe place for future use. It

must be re-fitted if the machine is to

be moved again. Re-fitting is car-

ried out by reversing the procedure.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Tighten the counternut using a

screwdriver as indicated.

Levelling the machine

The machine must be perfectly level to

ensure safe and proper operation.

This machine is not intended for in-

tegrated installation or installation

under a continuous worktop. The

UBW building under kit cannot be

used with sloping facia

machines.

Building under

However, the machine,

- complete with its own lid which

must not be removed, -

can still be slid under a worktop, if

there is enough space.

The machine must be allowed to jut out

sufficiently for the control panel not to

be obscured.

Incorrect installation may increase

water and electricity consumption.

The screw feet can be adjusted to level

the machine:

Washer-Dryer stack

A Miele tumble dryer can be stacked

with this washing machine. A stacking

kit* is necessary.

All parts marked * are available from

the Miele Spare parts or Sales Depart-

ment, and from some Miele Dealers.

Unscrew the foot or feet until the ma-

chine stands level.

Hold the foot tight using a pipe

wrench.

Download from Www.Somanuals.com. All Manuals Search And Download.

Plumbing

Connection to water supply

If replacing the inlet hose only use a

hose able to withstand pressure of up

to 70 bar. This also applies to all fittings

used. Miele original parts fulfil this con-

dition.

The machine should be connected to a

mains water supply in accordance with

standard regulations. The German auth-

orities do not require it to have a non-re-

turn valve as the washing machine has

been designed to comply with DVGW

regulations (German Association of

Gas and Water Engineers, see data

plate).

Longer hoses 2.5 or 4.0 m in length are

available as optional extras.

The pressure hose and solenoid inlet

valve are designed for a water flow

pressure of between 1 and 10 bar. At

higher water pressures it is essential to

fit a reducer valve.

Connection to a mains water supply

should be carried out by a qualified

plumber and should incorporate a

mains stopcock with 3/4" thread.

There is a minimum flow pressure of 1

bar pressure if 5 litres of water flow into

a suitable container in 15 seconds.

The 1.5 m long 3/8" pressure hose

should be connected to the stopcock

via the 3/4" threaded union.

The two dirt filters, one in the open

end of the inlet hose, one at the inlet

point in the solenoid valve must not

be removed.

This hose is not suitable for use for con-

nection to a hot water supply. Please

make sure that the washer sits correctly

in the union.

If connection is to be made to a stop-

cock with a short 3/4" thread, the extra

washers enclosed should also be in-

serted in the inlet hose union to com-

pensate.

The connection points are subject to

mains water pressure. Turn on the stop-

cock slowly and check for leaks. Cor-

rect the positioning of the washers and

screw unions if appropriate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Plumbing

Connection to the drainage system

Drain hose connection:

The machine drains via a drain pump

with a delivery head of 1 metre.

Direct into a sink: Hook the hose

over the edge and secure. Make

sure that the water can flow freely to

avoid flooding and to prevent water

from being sucked back into the ma-

chine.

The drain hose is 1.5 m long. It must

not be kinked as this restricts drainage.

The swivel elbow at the end of the hose

can be turned in either direction, or can

be detached if required with a sharp

twist and pull.

Connected to a standpipe.

Connected to a plastic drain pipe

with a rubber nipple. There is no

need to use a non-return valve.

Allow the water to drain off into a

floor drain.

If required, the hose can be extended

to a length of 5 m. The necessary parts

can be purchased from the Miele

Spare Parts department.

For a delivery head of more than 1 m

(up to a maximum of 1.8 m) a second

Duo drain pump is available with the

corresponding conversion kit from the

Miele Spare Parts Department.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical connection

This machine is supplied ready for con- The wire which is coloured brown must

nection to an a.c. single phase 230 -

240 V, 50 Hz supply. The machine is

supplied with a 2 m long mains cable

with moulded plug. The voltage, rated

load and fuse rating are given on the

data plate. Please ensure that these

match the household mains supply.

be connected to the terminal which is

marked with the letter L or coloured red.

WARNING

THIS APPLIANCE MUST BE

EARTHED

Non-rewireable plugs BS 1363

All electrical work should only be car-

ried out by a suitably competent per-

son, in accordance with national and

local safety regulations.

If this machine or appliance is fitted

with a non-rewireable plug, the follow-

ing information applies:

Connection should be made via a

fused plug and a suitable switched

socket which is easily accessible. For

extra safety it is advisable to install a re-

sidual current device (RCD) with a trip

current of 30 mA.

If the socket outlets are not suitable for

the plug supplied with this product, it

must be cut off and an appropriate

plug fitted.

The plug cut from the flexible cord

should be disposed of and on no ac-

count be inserted into any socket else-

where in the house (electric shock ha-

zard).

The fuse cover must be refitted when

changing the fuse, and if the fuse

cover is lost, the plug must not be used

until a suitable replacement is ob-

tained. The colour of the correct re-

placement is that of the coloured insert

in the base of the plug, or the colour

that is embossed in words in the base

of the plug (as applicable to the design

of plug fitted). The correct fuse rating of

the replacement fuses that are ASTA

approved to BS 1362 should be fitted.

Replacement fuse covers may be pur-

chased from your local electrical sup-

pliers, or Miele Service Agent.

Important

The wires in the mains lead are col-

oured in accordance with the following

code:

Green/yellow = earth

Blue = neutral

Brown = live

As the colours of the wires in the mains

lead of this appliance may not corre-

spond with the coloured markings ident-

ifying the terminals in your plug, pro-

ceed as follows:

The wire which is coloured green and

yellow must be connected to the termi-

nal in the plug which is marked with the

letter E or by the earth symbol z or col-

oured green or green and yellow.

The wire which is coloured blue must

be connected to the terminal which is

marked with the letter N or coloured

black.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions - Selection

With the programmable functions you

can adapt the machine to your individ-

ual requirements. A function stays pro-

grammed in memory until it is can-

celled.

The washing machine ignores any

changes after the first three minutes of

starting the programme, for example if

the programme selector switch is set to

a different setting or an additional pro-

gramme is selected.

The following programmable func-

tions are avalable:

– The “On” light starts flashing

Once the programme selector switch is

turned back to its original position the

“On” light stops flashing.

A High water level

Where rinse results are particularly im-

portant.

To cancel a programme for which the

lock has been programmed:

Effective for the rinses in programmes:

– COTTONS

Turn the programme selector switch

to “Finish/Start”.

– MINIMUM IRON

The programme sequence indicator

lamps start flashing in succession after

approx. 30 seconds.

– QUICK WASH 40°C

B Extra rinse for Cottons

You can select a different programme

as soon as only the “On” light lights up.

programmes

For soft water areas (water hardness

range 1).

D Gentle action

Where rinse results are particularly im-

portant in soft water areas an extra

rinse can be selected as well as high

water level.

For gentle washing of slightly soiled

items. Drum movement is reduced.

The “Gentle action” function is avail-

able for COTTONS, MINIMUM IRON

and QUICK WASH 40°C.

C Programme Lock

(Child safety feature)

Programme lock prevents:

Activating the programmable

functions is described on the follow-

ing pages.

– a wash programme being changed

into another

– unplanned opening of the door

– altering the additional functions set

for example by playing children.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions - To programme

Programming and saving the

programmable functions

2. Activate programmable function

6 For the function required turn the pro-

gramme selector to the appropriate

setting as follows:

Programmable functions are activated

using a combination of the buttons for

the optional functions with the pro-

gramme selector switch. These combi-

nations can call up extra functions not

displayed on the control panel.

– for High Water Level

programmable function A

turn to SEPARATE RINSE

– for Extra rinse

programmable function B

turn to Drain

Programming takes place in three

steps:

– for Programme lock

programmable function C

turn to QUICKWASH 40°C

– select programming mode

– activate programmable function

– for Gentle action

– store programmable function in

memory

programmable function D

turn to DELICATES 50°C

7 Quickly press the “Short wash” but-

ton 4 times, (eg in and out twice).

1. Select programming mode

The indicator light “Rinses/Rinse hold”

now lights up in the sequence display.

1The machine must be switched off

and the door closed. All pushbutton

switches must be released and pro-

gramme selector pointing to “Finish /

Start”.

The programmable function is now acti-

vated.

8If you wish to activate more than one

programmable function, repeat

steps 6 and 7. If not, then:

2Press in the “Soak” and “Short wash”

buttons.

3 Press in the “I-ON / O-OFF” button.

4 Release the “SOAK” button.

3. Save the programmable function

9 Press the I-ON /0-OFF button to re-

lease it.

5 Release the “Short wash” button.

The machine is now switched off and

the programmable function(s) stored in

memory.

The “ON” light now comes on in the se-

quence display and the “Main wash”

light flashes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programmable functions - Check/Cancel

To check the programmable

function:

To cancel the programmable

function:

To see if a selected programmable

function has been activated, carry out

Steps 1 to 6.

Repeat the steps 1 to 9.

– In step 7 the “Rinses/Rinse hold"

light now goes out.

– If the “Rinses/Rinse hold" light

comes on , the relevant programm-

able function is activated.

– In step 9 (Press the I-ON / 0-OFF

button) the programmable function is

cancelled.

Press the I-ON / 0-OFF button.

This finishes the check.

Download from Www.Somanuals.com. All Manuals Search And Download.

Consumption data

Normal Programmes

(without any additional options

or programmable functions)

Load

Electricity Water in

Time

normal

Time

short wash

in kWh

litres

Cottons 95°C

Cottons 60°C*

Cottons 40°C

Minimum iron 40°C

Delicates 30°C

Woollens 30°C

Starch

5.0 kg

2.5 kg

1.0 kg

5.0 kg

1.80

1.05

0.55

0.45

0.40

0.20

1 h 52 mins 1 h 24 mins

1 h 47 mins 1 h 12 mins

1 h 35 mins 1 h 02 mins

1 h 20 mins

1 h 00 mins

49 mins

43 mins

41 mins

–

19 mins

Consumption data can vary from the nominal values given as a result of water

pressure, water hardness, water inlet temperature, room temperature, type of

load, volume, fluctuations in the electricity supply and any additional options or

functions selected.

* according to Standard: EN 60456

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical data

Height. . . . . . . . . . . . . . . . . . . . . . . . . .

85 cm

59.5 cm

60 cm

97 cm

94 kg

Width . . . . . . . . . . . . . . . . . . . . . . . . . .

Depth . . . . . . . . . . . . . . . . . . . . . . . . . .

Depth with door open . . . . . . . . . . . . .

Weight . . . . . . . . . . . . . . . . . . . . . . . . .

Max. floor load . . . . . . . . . . . . . . . . . . .

Capacity. . . . . . . . . . . . . . . . . . . . . . . .

1600 Newton (approx. 160 kg)

5 kg dry laundry

Voltage . . . . . . . . . . . . . . . . . . . . . . . . .

Rated load . . . . . . . . . . . . . . . . . . . . . .

Fuse rating . . . . . . . . . . . . . . . . . . . . . .

see Data plate

}

Water flow pressure min. . . . . . . . . . . .

Static water pressure max.. . . . . . . . . .

Drain pump head max. . . . . . . . . . . . .

Drain pump length max.. . . . . . . . . . . .

Test certificates awarded. . . . . . . . . . .

Electrically suppressed according to. .

1 bar

10 bar

1 m

5 m

Radio/tv suppression, VDE

DIN EN 60555/VDE 0838

Download from Www.Somanuals.com. All Manuals Search And Download.

Alteration rights reserved/003

4997

This paper consists of cellulose which has been bleached without the use of chlorine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Cordless Saw 0729 20 User Manual
Multiquip Portable Generator DCA 125SSJU User Manual
Multiquip Power Roller MDR 9DYE User Manual
NAD Stereo Receiver T 765 User Manual
NEC Projector NP100 200 User Manual
Nortel Networks Switch 10292FA User Manual
Olympus Computer Drive MAFP 1E User Manual
Optimus CD Player CD 3322 User Manual
Panasonic Digital Camera DMC FS62 User Manual
Panasonic Switch AJ8R User Manual