Operating and installation instructions
Cooker hood
To prevent the risk of accidents or damage to the appliance, it is
essential to read these instructions before it is installed and used for
the first time.
en-GB
M.-Nr. 09 704 890
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Drilling diagram for wall mounting......................................................................... 34
Connection for air extraction.............................................................................. 35
Condensate trap.................................................................................................... 36
Electrical connection........................................................................................... 38
Activating Con@ctivity 2.0................................................................................... 39
Activating Con@ctivity 2.0..................................................................................... 39
Activation check............................................................................................... 39
Technical data...................................................................................................... 41
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This appliance complies with all relevant local and national safety
requirements. Inappropriate use can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before using it for the first
time. They contain important notes on the safety, installation, use
and maintenance of the appliance. Miele cannot be held liable for
non-compliance with these instructions.
Keep these instructions in a safe place and ensure that all users
are familiar with the contents. Pass them on to any future owner of
the appliance.
Correct application
This cooker hood is intended for use in domestic households and
similar working and residential environments.
The cooker hood is not intended for outdoor use.
It must only be used as a domestic appliance to extract vapours
and remove odours from cooking.
Any other usage is not supported by the manufacturer and could be
dangerous.
The cooker hood can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and recognise and understand the
consequences of incorrect operation.
Safety with children
Children under 8 years of age must be kept away from the cooker
hood unless they are constantly supervised.
Children 8 years and older may only use the cooker hood
unsupervised if they have been shown how to use it safely and
recognise and understand the consequences of incorrect operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Children must not be allowed to clean or maintain the cooker
hood unsupervised.
Please supervise children in the vicinity of the cooker hood and
do not let them play with it.
Danger of suffocation. Packaging, e.g. plastic wrappings, must be
kept out of the reach of babies and children. Whilst playing, children
could become entangled in packaging or pull it over their head and
suffocate.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Unauthorised installation, maintenance and repairs can cause
considerable danger for the user. Installation, maintenance and
repairs must only be carried out by a Miele authorised technician.
A damaged appliance can be dangerous. Check it for visible signs
of damage. Do not use a damaged appliance.
The electrical safety of this appliance can only be guaranteed
when correctly earthed. It is essential that this standard safety
requirement is met. If in any doubt please have the electrical
installation tested by a qualified electrician.
Before connecting the appliance to the mains supply, ensure that
the connection data on the data plate (voltage and frequency) match
the mains electricity supply. This data must correspond in order to
avoid the risk of damage to the appliance. Consult a qualified
electrician if in any doubt.
Do not connect the appliance to the mains electricity supply by a
multi-socket unit or an extension lead. Extension leads are a fire
hazard and do not guarantee the required safety of the appliance.
For appliances with an external motor fitted (...EXT models) the
connection of the two units must be made using the connection
cable and the plug connectors.
These models may only be combined with a Miele external motor.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
For safety reasons, this appliance may only be used after it has
been built in.
The cooker hood must not be used in a non-stationary location
(e.g. on a ship).
Tampering with electrical connections or components and
mechanical parts is highly dangerous to the user and can cause
operational faults.
Only open the housing as described in the instructions given in the
installation sheet and in the Cleaning and care section of this
booklet. Under no circumstances should any other parts of the
housing be opened.
The manufacturer's warranty will be invalidated if the appliance is
not repaired by a Miele approved service technician.
Miele can only guarantee the safety of the appliance when
genuine original Miele replacement parts are used. Faulty
components must only be replaced by Miele spare parts.
If the electrical connection cable is faulty it must only be replaced
by a Miele authorised service technician to protect the user from
danger.
During installation, maintenance and repair work, the appliance
must be disconnected from the mains electricity supply.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Using at the same time as other heating appliances that depend on the air
from the room
Warning - danger of toxic fumes
Great care should be taken when using the cooker hood at the
same time and in the same room or area of the house as another
heating appliance which depends on the air in the room.
Such appliances include gas, oil, wood or coal-fired boilers and
heaters, continuous flow or other water heaters, gas hobs,
cookers or ovens which draw air in from the room and duct
exhaust gases out through a chimney or extraction ducting.
When used in extraction mode, with or without an external motor
fitted, the appliance draws air in from the room in which it is
installed and from neighbouring rooms.
If there is insufficient air, an underpressure will occur. The heating
appliance will be starved of oxygen, impairing combustion.
Harmful gases could be drawn out of the chimney or extraction
ducting back into the room, with potentially fatal consequences.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
In order to ensure safe operation, and to prevent gases given off
by the heating appliances from being drawn back into the room
when the cooker hood and the heater are in operation
simultaneously, an underpressure in the room of 0.04 mbar (4 pa)
is the maximum permissible.
Ventilation can be maintained by air inlets which cannot be
blocked, in windows, doors or outside wall vents, or by other
technical measures, such as ensuring that the cooker hood can
only be switched on when the heating appliance is switched off or
vice versa. A ventilation brick alone is not generally sufficient to
ensure safe ventilation.
The overall ventilation condition of the dwelling must be taken into
account. If in any doubt, the advice of a competent builder or, for
gas a qualified gas fitter (registered with an official gas safety
body in accordance with national safety regulations, GasSafe in
the UK) must be sought.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct use
Never use an open flame beneath the cooker hood. To avoid the
danger of fire, do not flambé or grill over an open flame.
When switched on, the cooker hood could draw flames into the filter.
Fat deposits could ignite, presenting a fire hazard.
The cooker hood can become damaged when exposed to
excessive heat.
– When using the cooker hood over a gas hob, ensure that any
burners in use are always covered by a pan. Switch the cooking
zone off when a pan is removed, even for a short time.
– Select a pan which is suitable for the size of the burner.
– Regulate the flame so that it does not burn up the sides of the
pan.
– Avoid overheating the pan (e.g. when cooking with a wok).
Always switch the cooker hood on when a cooking zone is in use,
otherwise condensation may collect in the hood, which could cause
corrosion.
When cooking with oil or fat, chip pans and deep fat fryers etc, do
not leave the pans unattended. Never leave an open grill unattended
when grilling. Overheated oil and fat can ignite and could set the
cooker hood on fire.
Do not use the cooker hood without the filters in place. This way
you will avoid the risk of grease and dirt getting into the appliance
and hindering its smooth operation.
The filters should be regularly cleaned or changed as appropriate.
Saturated filters are a fire hazard.
The cooker hood can get very hot during cooking due to heat
rising from the hob.
Do not touch the housing or the grease filters until the cooker hood
has cooled down.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct installation
Refer to the cooker or hob manufacturer's instructions as to
whether a cooker hood may be operated above the cooker/hob.
Safety regulations prohibit the fitting of a cooker hood over solid
fuel stoves.
Insufficient distance between the cooker or hob and the cooker
hood can result in damage to the hood.
The minimum safety distances between the top of the cooker or hob
and the bottom of the cooker hood given in the "Installation" section
must be maintained, unless the hob manufacturer states that a
greater distance is required.
If more than one cooking appliance is fitted beneath the cooker
hood, and they have different minimum safety distances to the
cooker hood, select the greater distance.
The distances given in "Installation" must be observed when
fitting the cooker hood.
Exhaust ducting must be of non-inflammable material. Suitable
material is available from Miele specialist dealers or the Miele Spares
Dept.
The appliance must not be connected to a chimney or vent flue
which is in use. Neither should it be connected to ducting which
ventilates rooms with fireplaces.
If exhaust air is to be extracted into a chimney or ventilation duct
no longer used for other purposes, seek professional advice.
Cleaning and care
Do not use a steam cleaning appliance to clean this appliance.
The steam could reach electrical components and cause a short
circuit.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Accessories
Only use genuine original Miele accessories with this appliance.
Using accessories from other manufacturers will invalidate the
guarantee, and Miele cannot accept liability.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Disposal of your old appliance
Electrical and electronic appliances
often contain valuable materials. They
also contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance. Please
do not therefore dispose of it with your
household waste.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Dealer for
advice.
Ensure that it presents no danger to
children while being stored for disposal.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Modes of operation
Depending on the model of the cooker
hood, the following options are
available:
Operation with an external
motor
(...EXT model cooker hoods)
Air extraction
A Miele extraction fan is installed in a
location of your choice outside the
room for cooker hoods which are
designed to be connected to an
external motor. The external motor is
connected to the cooker hood by
means of a control cable and is
operated by Con@ctivity 2.0 or by the
controls on the cooker hood.
The air is drawn in and cleaned by the
grease filters and directed outside.
Non-return flap
The non-return flap is designed to
prevent the exchange of room and
outside air taking place.
The flap is closed when the cooker
hood is switched off.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
If the on-site ventilation system does
not have a non-return flap, the non-
return flap supplied must be fitted in the
exhaust socket in the motor unit.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Modes of operation
The hob transmits information about its
operational status via a radio signal to
the cooker hood.
Con@ctivity 2.0 function
Automatic control
The cooker hood has a communication
facility which enables the automatic
operation of the cooker hood
depending on the operational state of
the hob.
– When the hob is switched on, the
hob lighting comes on independently
and then after a short time the fan
also comes on.
– During cooking the cooker hood
automatically sets the power level
according to the number of cooking
zones in operation and their power
levels.
– After switching the hob off the fan
and the hob lighting will switch off
automatically after a specified period
of time.
See "Operation" for detailed
information about this function.
To make use of the communication
facility the hob must be fitted with a
Con@ctivity 2.0 Stick .
Refer to the installation instructions for
the Con@ctivity 2.0 Stick to check
whether it is compatible with your hob.
To use the Con@ctivity 2.0 function, a
wireless connection must be
established between the hob and the
cooker hood (see "Activating
Con@ctivity 2.0").
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
a
b
c
d
e
f
g
h
i
j
k
Telescopic extension piece
Tower
Canopy
Controls
Grease filters
Hob lighting
Control for the hob lighting
On/Off control for the fan
Controls to select the fan power level
Control for the run-on option
Operating hours control
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic mode)
When Con@ctivity 2.0 is activated, the
cooker hood always works in automatic
mode (see "Activating Con@ctivity
2.0").
Reaction time
The cooker hood reacts with a slight
delay because altering the power level
on the hob does not immediately result
in a reduction or increase in cooking
vapours.
To operate the cooker hood manually,
see "Cooking without Con@ctivity 2.0".
Because the hob transmits the
information to the cooker hood at
intervals, this can also cause delays.
Cooking with Con@ctivity 2.0
(Automatic mode)
Switch a cooking zone on at the
The reaction can vary from a few
seconds to a couple of minutes.
power level you want.
The cooker hood lighting will come on.
After a few seconds the fan will come
on, first at power level 2, then it will
switch immediately to power level 1.
The cooker hood selects the power
level automatically during cooking.
This is determined by the total output of
the hob, i.e, the number of cooking
zones in operation and the power levels
selected.
If you select a higher power level or
are using several cooking zones, the
cooker hood will switch to a higher
power level.
When you reduce the power level or
the number of cooking zones on the
hob, the cooker hood power level is
also reduced.
Examples for power levels 1 to 4
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic mode)
Cooking process
Switching off
If for example you switch on a
cooking zone at the highest power
level to heat a pan for frying and
reduce the power level after approx.
60 to 90 seconds*, a cooking process
is recognised (*60 seconds to 5
minutes for a HiLight hob).
Switch off all cooking zones.
The cooker hood fan will reduce its
power level over the next few minutes
and will eventually switch itself off.
This helps to neutralise any lingering
vapours and odours in the air.
The cooker hood switches itself on and
when the hob power level has been
reduced, the hood switches to power
level 3 and remains at that level for
approx. 5 minutes.
– From the intensive setting IS the fan
switches immediately to level 3.
– From level 3, it switches to level 2
after approx. 1 minute.
– From level 2 it switches to level 1
after approx. 2 minutes.
After that the cooker hood power level
is determined automatically by the
Con@ctivity function.
– After 2 minutes at level 1 the fan
switches itself off.
You can select another power level
manually before then.
– After another 30 seconds the lighting
switches off.
The cooking process is then finished.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic mode)
Leaving automatic mode
temporarily
To leave automatic mode temporarily
during cooking:
Returning to automatic mode
The cooker hood returns to automatic
mode:
if the cooker hood has not been used
for approx. 5 minutes after selecting
a power level manually, or
Manually select a different power
level, or
if the manually selected fan power
level corresponds to the automatic
one again, or
Manually switch the cooker hood off,
or
Activate the run-on option on the
cooker hood. The fan will switch off
after the selected time and the
if the cooker hood fan and the hob
have been switched off for at least 30
seconds.
Automatic mode will resume next
time the hob is switched on.
lighting remains switched on.
The cooker hood can now be operated
manually (see "Cooking without
Con@ctivity 2.0").
If you wish to operate the cooker
hood manually for a complete
cooking process, switch on the
cooker hood fan before switching on
the hob.
If the cooker hood and the hob have
been switched off for at least 30
seconds after cooking, automatic
mode will resume the next time the
hob is switched on.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Manual mode)
After you have finished cooking,
press the run-on option control 5
15
Cooking without Con@ctivity
2.0 (Manual mode)
The cooker hood can be operated
manually if:
– Once: the fan will switch off after 5
minutes (5 will light up).
– Con@ctivity 2.0 is not activated.
– Twice: the fan will switch off after 15
– You have temporarily deactivated
Con@ctivity 2.0 (see "Leaving
automatic mode temporarily").
minutes (15 will light up).
– If you press the run-on option control
5 15 again, the fan will remain on
(5 15 will go out).
Switching the fan on
Press the On/Off control .
Switching the fan off
Use the On/Off control to switch
the fan off.
The fan will switch on at level 2. The
symbol and 2 will light up in the power
level display.
The symbol will go out.
Selecting the power level
For light to heavy cooking vapours and
odours, select from power levels 1 to 3.
Switching the hob lighting on /
off
The hob lighting can be switched on
and off independently of the fan.
When frying or cooking food with a very
strong aroma, select the Intensive
setting IS.
To do this, press .
For a lower power level, press the
"" control, or "" for a higher level.
The symbol will light up when the
hob lighting is switched on.
Reducing power on the intensive
setting
If Power management is activated
(default), the fan automatically switches
to level 3 after 5 minutes.
Selecting run-on time
It is advisable to run the fan for a few
minutes after cooking has finished to
neutralise any lingering vapours and
odours in the air.
With the run-on option the fan switches
itself off automatically after a pre-
selected time.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Manual mode)
Switching Power management
on /off
Power management
The cooker hood features a power
management system for switching off
the lighting and reducing the fan power
level automatically.
Switch off the fan and the lighting.
Press the run-on option control 5
15 for approx. 10 seconds, until 1
lights up in the power level display.
– If the Intensive setting has been
selected the cooker hood will
automatically switch down to power
level 3 after 5 minutes.
Then press in turn,
– the lighting control ,
– the "" control and then
– the lighting control again.
– From levels 3, 2 or 1 the power will
be reduced by one level after 2 hours
and then in 30 minutes stages until
the fan finally switches off.
If Power management is switched on,
the 1 and IS indicators will light up
constantly.
– The hob lighting will switch off
automatically after 12 hours.
If it is switched off, 1 and IS will flash.
Press "" to switch Power
management off.
The 1 and IS indicators will flash.
To switch it on, press "".
The 1 and IS indicators will light up
constantly.
Confirm the setting with the run-on
option control 5 15.
All the indicators will go out
If you do not confirm within 4 minutes,
the cooker hood will revert to the old
setting.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic and Manual modes)
Fan power level indicators 1 to IS show
the time set:
Operating hours counter
The number of hours the appliance has
been in operation is stored in memory.
1............................................... 20 hours
2............................................... 30 hours
3............................................... 40 hours
IS............................................. 50 hours
When the Grease filter symbol , lights
up, the operating hours counter is
signalling that the filters need to be
cleaned or changed. Further
information about cleaning and
changing the filters and resetting the
operating hours counter can be found
under "Cleaning and care".
Press the "" symbol for a shorter
operating time, or the "" symbol to
select a longer operating time.
Confirm the selection by pressing the
operating hours control .
Altering the operating hours counter
for the grease filters
All the indicators will go out
You can set the operating hours
counter for the grease filters to suit the
type of cooking you do.
If you do not confirm within 4 minutes,
the cooker hood will revert to the old
setting.
The grease filter operating hours
counter is set at the factory for 30
hours.
– Select a shorter time of 20 hours if
you roast or fry a lot.
– If you only cook occasionally we
recommend that you still select a
short time because grease which has
built up gradually over a long period
of time will harden on the filters and
make cleaning more difficult.
– Select a longer time of 40 or 50
hours if you use very little fat for
cooking.
Use the On/Off control to switch
the fan off.
Press the run-on control 515 and
the operating hours control at
the same time.
The grease filter symbol and one of
the fan power level indicators flash.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation (Automatic and Manual modes)
Reading the filter operating hours
counter
To check the percentage of time set
already used
Press the On/Off control to switch
the fan on.
Press and hold the operating hours
control .
The grease filter symbol lights up.
One or more of the power level
indicators will flash.
The number of fan power level
indicators flashing shows the
percentage of the operating time which
has already been used up.
1 ................................................... 25 %
1 and 2 ......................................... 50 %
1 to 3 ............................................ 75 %
1 to IS ......................................... 100 %
The number of operating hours used
remains in the memory, even when
the appliance is switched off or there
is a power cut.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
To help prevent re-soiling, a
Housing
proprietary conditioning agent for
stainless steel (available from Miele)
can also be used. Follow the
manufacturer’s instructions on the
packaging.
General information
The surfaces and controls are
susceptible to scratches and
abrasion.
Special instructions for appliances
with lacquered housing
Please observe the following
cleaning instructions.
(Special order finish)
All external surfaces and controls can
be cleaned using hot water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
Please observe the general notes on
cleaning earlier in this section.
It is very difficult to clean this type of
surface without causing minor marks
to the surface material. This can
become particularly noticeable if there
is halogen lighting in the kitchen.
Do not use too much water when
cleaning the controls.
Water could penetrate into the
electronics and cause damage.
Important for the controls
After cleaning, wipe the surfaces dry
using a soft cloth.
Do not leave soiling on the controls
for any length of time.
Otherwise they may suffer
discolouration or damage.
Remove soiling straight away.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents. These will damage
the surface material.
Please observe the general notes on
cleaning earlier in this section.
Do not use stainless steel cleaning
agents on the controls.
Grease filters
Important for appliances with
stainless steel surfaces
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
cooker hood.
(This information does not apply to the
controls).
Stainless steel surfaces can be
cleaned with a proprietary non-
abrasive cleaning agent designed
specifically for use on stainless steel.
An oversaturated filter is a fire
hazard.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning interval
Cleaning the grease filters by hand
The grease filters should be cleaned
regularly (at least every 3 - 4 weeks) to
avoid a build-up of grease.
Clean the filters with a soft nylon
brush in a mild solution of hot water
and a small amount of washing-up
liquid. Do not use "neat" washing up
liquid.
Clean them immediately if the Grease
filter operating hours symbol lights
up.
Unsuitable cleaning agents
You can set the operating hours
counter for the grease filters to suit
the type of cooking you do (see
"Operation").
Unsuitable cleaning agents can cause
damage to the surface of the filter if
used regularly.
Do not use:
– cleaning agents containing descaling
agents
Removing a grease filter
The grease filter can fall out when
you are handling it.
– powder cleaners, cream cleaners
– aggressive all-purpose cleaning
agents or spray cleaners for grease
This can result in damage to the filter
and the hob below.
Make sure you hold the filter
securely at all times when handling
it.
– oven sprays
Cleaning the grease filters in the
dishwasher
Place the filters as upright as
possible in the lower basket, with the
short sides upright, ensuring the
spray arm is not obstructed.
Use a proprietary household
dishwasher detergent.
Select a dishwasher programme with
a wash temperature between 50°C
and 65°C.
Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.
To take out a grease filter, release the
locking clip on the filter, lower the
filter approx. 45°, unhook it at the
back and remove it.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
After cleaning
Press the operating hours control
for approx. 6 seconds, until only
the 1 is flashing.
After cleaning, leave the filters to dry
on an absorbent surface before
replacing them.
When removing the filters for
cleaning, also clean off any residues
of oil or fat from the now accessible
housing to prevent the risk of these
catching fire.
Replace the grease filters, making
sure that the locking clips are facing
down towards the hob.
If a grease filter is inadvertently
replaced upside down, insert a small
screwdriver blade into the slit to
disengage the clip.
Resetting the grease filter operating
hours counter
After cleaning, the operating hours
counter needs to be re-set.
Whilst the fan is switched on, press
the operating hours control for
approx. 3 seconds, until only the 1 is
flashing.
The grease filter symbol goes out.
If you want to clean the grease filter
before the operating hours counter has
reached its maximum,
27
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales / Guarantee
In the event of a fault which you cannot
remedy yourself, please contact your
Miele dealer or the Miele Service
Department.
Contact details for Miele are given at
the back of this manual. N.B. A call-out
charge will be applied to service visits
where the problem could have been
resolved as described in these
instructions.
When contacting your dealer or Miele,
please quote the model and serial
number of your appliance.
These are shown on the data plate.
Position of the data plate
The data plate is visible after removing
the grease filters.
Guarantee
The appliance is guaranteed for 2 years
from the date of purchase. For further
information on the appliance guarantee
specific to your country please contact
Miele.
In the UK, you must activate your cover
by calling 0845 365 6640 or registering
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Before installation
Dismantling
Should the appliance ever need to be
dismantled, follow the installation
instructions in reverse order as
described on the installation sheet. A
lever is supplied to assist with the
removal of the tower.
Before installation, it is important
to read the information given on the
following pages as well as the
"Warning and Safety instructions" at
the beginning of this booklet.
After unscrewing the two fixing
screws on the tower,
Protective foil
The housing components have
protective foil around them to protect
them from transport damage.
Please remove this foil before fitting
the housing components. It can be
peeled off easily.
Installation instructions
See enclosed Installation sheet for
instructions on how to install this
appliance.
push the lever between the tower and
the extension piece
then lever the tower out of its fixings.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
a
b
c
d
3 protective sheets
for use when fitting the tower
1 exhaust connection
6 screws 5 x 60 mm and
6 plugs 8 x 50 mm
for securing the wall bracket
for exhaust ducting 150 mm
1 reducing collar
for exhaust ducting 125 mm
The screws and plugs are designed
for use in solid walls only.
For other types of wall construction,
alternative fixings will be required.
Make sure the wall is able to take the
weight of the cooker hood.
1 non-return flap
for fitting into the exhaust
connection on the motor unit
e
Telescopic wall bracket
for securing the cooker hood to the
wall
2 x M 6 self-tapping nuts
for securing the appliance
2 screws 3.9 x 7.5 mm
for securing the tower
1 lever
for dismantling the tower
Installation instructions
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
ab
The shaded area represents the wall or ceiling area for the vent cut-out, for
fitting the connection socket and on EXT models for feeding the connection
cable through to the external motor.
Connection for air extraction 150 mm, or 125 mm with reducing collar.
Safety distance between hob and cooker hood
When planning the installation height of your cooker hood, the minimum safety
distance between the top of a cooker or hob and the bottom of the cooker
hood is as follows, unless a greater distance is specified by the manufacturer of
your cooking appliance.
See "Warning and Safety" instructions for further information.
Cooking appliance
Electric hob
Minimum distance S
450 mm
Electric grill
650 mm
Deep fat fryer (electric)
650 mm
Multi-burner gas hob with a maximum total output of
12.6 kW, no burner exceeding 4.5 kW.
650 mm
Multi-burner gas hob with a total output of more than
12.6 kW, or a multi-burner gas hob where one burner
exceeds 4.5 kW.
760 mm
Single gas burner with a maximum output of 6 kW.
Single gas burner with output exceeding 6 kW.
650 mm
760 mm
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation recommendations
Drilling diagram for wall
mounting
Please follow the directions given in
the installation instructions supplied
for drilling.
– When deciding on the safety
distance between the hob and
cooker hood, please note that a
distance of 650 mm above electric
cookers/hobs may be preferable to
give more working space under the
hood.
– Account should also be taken of the
height of the person who will be
using the hood most often. They
should have sufficient space to work
comfortably at the hob, and be able
to reach the hood controls with ease.
– Please be aware that if positioned
too high, extraction will be inefficient.
– To achieve optimum vapour
extraction, the cooker hood must
cover the hob. It should be
positioned centrally over the hob, not
to the side.
– The hob should be no wider than the
cooker hood, and if possible, it
should be narrower.
– The installation area must be easily
accessible. The cooker hood should
be easily accessible and easy to
dismantle in the event that service is
required. This should be taken into
consideration when planning the
position of cupboards, shelves,
ceilings or features in the vicinity of
the cooker hood.
For pre-installation of a back wall
where the holes have to be pre-
drilled, please refer to the drilling
distances in the drawing above
(screws 5 mm).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
– The exhaust ducting should be as
short and straight as possible.
Before installation, it is important
to read the information given on the
following pages as well as the
"Appliance dimensions" and the
"Warning and Safety instructions" at
the beginning of this booklet. This is
particularly crucial when using the
cooker hood at the same time as a
heating appliance that relies on
oxygen from the same room, which
could result in the build-up of toxic
fumes.
It is essential that the "Warning and
Safety" instructions are observed.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– Only use wide radius bends.
– The exhaust duct must not be kinked
or compressed.
– Ensure that all connections are
strong and airtight.
Remember that any constriction of
the air flow will reduce extraction
performance and increase operating
noise.
If the exhaust is ducted through an
outside wall, a telescopic wall vent or
a roof vent (available as an optional
accessory) is recommended.
Use smooth or flexible ducting made
from approved non-flammable
materials for exhaust ducting.
When using an external motor, make
sure that the exhaust ducting is
sufficiently rigid. The external motor
can cause an underpressure which
can result in the exhaust ducting
distorting.
If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
To achieve the most efficient air
extraction with the lowest noise
levels, please note the following:
When ducting is horizontal it must be
laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the appliance.
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
If the exhaust ducting is to run
through rooms, ceiling space etc.
where there may be great variations
in temperature between the different
areas, the problem of condensation
– If flat ducting is being used, the cross
section must not be smaller than the
cross sectional area of the exhaust
connection.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
will need to be addressed. The
exhaust ducting will need to be
suitably insulated.
Silencer
Condensate trap
To achieve even further reductions in
noise levels, a special silencer (optional
accessory) can be fitted in the ducting
system.
Air extraction
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur.
Condensate traps are available for 125
mm or 150 mm ducting.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust connection.
The arrow on the housing indicates
the direction of air-flow.
The silencer not only reduces noise
from the motor outside the house, but
also sounds from outside (e.g. traffic
noise). For this reason the silencer must
be positioned as close as possible to
the ducting exit .
The condensate trap is integrated in
cooker hoods which are designed for
connection to an external motor
(model......EXT).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
Air extraction with external motor
To minimise noise from the motor in the
kitchen, the silencer should be
positioned in front of the external motor
if possible, or, if the ducting is long,
above the exhaust connection inside
the hood . In the case of an external
motor located inside the house, fitting a
silencer behind the external motor
reduces the noise of the motor outside
the house.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
If the switch is not accessible after
installation (depending on country), an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national and
local safety regulations (BS 7671 in
the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
Important
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
This appliance is supplied for
connection to an a.c. 230 V single
phase 50 Hz supply. The wires in the
mains lead are coloured in accordance
with the following code:
Green/yellow ..................................earth
Blue..............................................neutral
Brown................................................live
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
WARNING:
THIS APPLIANCE MUST BE
EARTHED
Connection of this appliance should be
made via a suitable isolator or a double
pole fused spur connection unit which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in. When
switched off there must be an all-pole
contact gap of 3 mm in the switch
(including switch, fuses and relays
according to EN 60335).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating Con@ctivity 2.0
– then the lighting control .
Installing the Con@ctivity 2.0
Stick
In order to use the Con@ctivity 2.0
function, the hob must first be fitted
with the Con@ctivity 2.0 Stick.
If Con@ctivity 2.0 is not activated, 2
and 3 will flash at the same time.
Press "" to activate Con@ctivity
2.0.
Please read the separate installation
instructions supplied with the
Con@ctivity 2.0 Stick.
2 will light up constantly and 3 will
flash. The search for a wireless
connection is started.
Meanwhile, start activating the hob.
Activating Con@ctivity 2.0
Wireless connection must be activated
between the cooker hood and the hob
before Con@ctivity 2.0 can be used.
Activating the hob
While the cooker hood is searching
for wireless connection, start
activating the hob.
More information about this can be
found in the operating instructions for
the hob.
Both appliances must be installed and
operational.
You only need to carry out the
activation procedure once. If the
appliances are disconnected from the
electricity supply, during a power cut
for example, they will still remain
activated.
When connection has been established,
2 and 3 will light up constantly on the
cooker hood.
Confirm activation of the cooker
hood with the run-on option control
515. All indicators will go out.
To establish the wireless connection,
the cooker hood and hob must be
activated at the same time.
First activate the cooker hood, then the
hob.
Confirm activation of the hob.
Con@ctivity 2.0 is now ready to use.
If you do not confirm your selection
within 4 minutes, activation will not take
place.
Activating the cooker hood
Switch off the fan, hob lighting and
hob.
Activation check
Press the run-on option control
515 for approx. 10 seconds until
the indicator for power level 1 lights
up.
To check whether Con@ctivity 2.0 is
activated on the cooker hood:
Switch off the fan and hob lighting.
Then press in turn,
– the "" control,
Press the run-on option control
515 for approx. 10 seconds until
the indicator for power level 1 lights
up.
– then the "" control,
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Activating Con@ctivity 2.0
Then press in turn,
– the "" control,
– then the "" control,
– then the lighting control .
If Con@ctivity 2.0 is activated, 2 and 3
will light up constantly.
If Con@ctivity 2.0 is not activated, 2
and 3 will flash at the same time.
To exit the check, press the run-on
option control 515. All indicators
will go out.
To check whether Con@activity is
activated on the hob, see the
operating instructions for the hob.
If connection cannot be established
despite activating the Con@ctivity
function on the cooker hood and
hob, the function must be
deactivated on both appliances and
then the procedure repeated.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Fan motor*
200 W
3 x 3 W
209 W
AC 230 V
5 A
Hob lighting
Total connected load*
Voltage
Fuse rating
Mains connection cable length
Weight
1.5 m
DA 422-6
27 kg
24 kg
DA 422-6 EXT
Extraction power* according to EN 61591, extraction ducting 125/150 mm
Level 1
180/200 m³/h
Level 2
280/300 m³/h
380/400 m³/h
580/640 m³/h
Level 3
Intensive setting
* For EXT models, the connected load and extraction power will depend on the type of
external motor fitted.
Length of connection cable to external motor: 1.9 m
Conformity declaration
Miele hereby declares that the cooker hoods listed at the end of this booklet
comply with the basic requirements and other relevant regulations of Guideline
1999/5/EC.
A copy of the full Declaration of Conformity can be obtained from the address at
the end of this booklet.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
DA 422-6
DA 422-6 EXT
en-GB
M.-Nr. 09 704 890 / 00
Download from Www.Somanuals.com. All Manuals Search And Download.
|
