Operating and Installation
Instructions
Fridge-Freezer Combination
KFN 14943 SD ed
en - CA
To prevent accidents
and machine damage
read these instructions
before
installation or use.
M.-Nr. 07 589 450
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation information
If the room is too cold, it will cause the
cooling system in the appliance to
switch off for too long. This may lead to
higher temperatures in the appliance
and the frozen food may even start
thawing!
Do not place any devices that
produce heat (such as a toaster or
microwave) on top of the appliance.
This would increase the energy
consumption of the appliance!
Proper ventilation
This fridge/freezer should not be
placed side-by-side with a second
model.
The air behind the appliance gets
warm. In order to ensure adequate
ventilation, you must make sure that the
ventilation slits are not covered or
blocked in any way.
Because the appliance does not
have heated side walls, a
side-by-side arrangement can lead
to the build-up of condensation
water.
Also, the ventilation slits must be
dusted/cleaned on a regular basis.
Contact your dealer for advice.
Installation
Location
^ First remove any cable clips from the
rear of the appliance.
The appliance should not be installed
directly next to a heat source (such as
a kitchen range or a heater) or in direct
sunlight. The higher the ambient
temperature, the longer the appliance
will run and the higher the energy
consumption.
^ Check that all the parts on the rear of
the appliance are free to move.
Remove any obstructions.
^ Gently slide the appliance into the
desired location.
Choose a dry, well-ventilated room for
installation.
^ The rear of the appliance can be
directly against the wall.
Climate range
The appliance is designed for use
within a certain climate range (room
temperature range) and should not be
used outside this range. The climate
range is stated on the data plate inside
the appliance.
Climate range
Room temperature
SN
N
+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
ST
T
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation information
Adjustments
^ Use the wrench provided to adjust
the feet as needed, so that the
appliance is level.
^ If necessary, unscrew the foot a
from the hinge bracket in order to
support the appliance door.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation information
Appliance dimensions
A
B
C
KFN 14943 SD ed
2020
750
630
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
The appliance comes with right-hand
hinging. If left-hand door hinging is
preferred, then follow these instructions
to change the door hinge:
You will need the following tools:
– a crosstip screwdriver,
– a flathead screwdriver,
– various sizes of Torx screwdrivers,
– a fork wrench.
Always change the door hinging
with the assistance of another
person.
Removing the door handles:
^ When you pull on the door handle a,
the sidebar b moves backwards.
^ Pull the sidebar b backwards out of
the track.
^ Now loosen the 4 screws (Torx 15) in
the mounting plate and remove the
handle.
^ Remove the covers from the opposite
side and place them on the holes that
are now vacant.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Before changing the hinging,
remove any items of food from the
shelves in the appliance door.
Removing the top soft-close
mechanism:
^ Open the top door of the appliance.
^ Slide the panel a in the direction of
the appliance and leave it hanging
between the door and the appliance.
^ Place the securing device b
(supplied with the appliance) on the
soft-close mechanism c so that it
engages.
With the securing device in place, the
joint cannot snap shut. Do not remove
the securing device until instructed to!
^ Loosen the panel a from the
soft-close mechanism: From below,
slide a flathead screwdriver into the
recesses, then slowly and carefully
lift off the panel.
Be careful not to damage the door
seal.
If the door seal is damaged, the
appliance door may not close
properly and there will not be
enough refrigeration!
^ Using a flathead screwdriver,
carefully lift the top and the bottom of
the cover d from the retainer.
^ Push the pin e up and out using a
flathead screwdriver.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Remove the cover d.
Removing the top door of the
appliance:
Now the soft-close mechanism and the
appliance are no longer connected.
^ Loosen the cover h by carefully
sliding a flathead screwdriver from
below into the recess.
^ Remove the panel a.
^ Push the shock absorber arm f as
far as possible towards the handle
side.
^ Remove the cover h together with
the mounting bracket i.
^ Loosen the three screws g on the
soft-close mechanism and the
spacer.
^ Loosen the mounting bracket i from
the cover h by pushing it slightly to
the left and then removing the cover
plate towards the front.
^ In the middle, pry out the housing
with the soft-close mechanism using
a flathead screwdriver.
^ Turn the mounting bracket i 180°.
^ Place the cover h onto the front of
the mounting bracket i and push it
to the right. The writing must be
visible.
^ Then, pry the housing with the
soft-close mechanism out of the
retainer from the appliance side.
^ Lay the soft-close mechanism aside.
^ Unscrew the bearing j mechanism,
turn it 180° and replace it on the
opposite side. If necessary,
^ Push out the spacer towards the
hinge side.
pre-punch the screw holes.
^ Lay the spacer aside.
^ Remove the top cover k by pushing
it from back to front and lifting it up.
^ Remove the cover l upwards.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Loosen the panel a of the soft-close
mechanism: Slowly pry the panel off
from the top.
Caution! The top door of the
appliance is no longer secured as
soon as the hinge bracket is
removed when following the
instructions below!
Be careful not to damage the door
seal.
If the door seal is damaged, the
appliance door may not close
properly and there will not be
enough refrigeration!
^ Close the top door of the appliance.
^ Loosen the screws m on the top
hinge bracket n and remove the
hinge bracket by pulling up.
^ Carefully lift and remove the top door
of the appliance and set aside.
^ Make sure that the bearing pin in the
middle of the appliance stays in
place, otherwise the bottom door of
the appliance has no hold!
^ Engage the cover h together with
the mounting bracket i on the
opposite side.
^ Slide the panel a in the direction of
the appliance and leave it hanging
between the door and the appliance.
^ Now place the cover l on the other
side.
^ Place the securing device b
(supplied with the appliance) on the
soft-close mechanism c.
Removing the bottom soft-close
mechanism:
With the securing device in place, the
joint cannot snap shut. Do not remove
the securing device until instructed to!
^ From the side, carefully lift off the
cover d using a flathead
screwdriver.
^ If necessary, lift the appliance
backwards slightly with the
assistance of another person.
^ Open the bottom door of the
appliance.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Lay the spacer aside.
Removing the bottom door of the
appliance:
^ Close the bottom door of the
appliance.
^ Push the pin e up and out.
Now the soft-close mechanism and the
appliance are no longer connected.
^ Remove the panel a.
^ Pull the bearing pin i in the middle
of the appliance up and out.
^ Carefully lift and remove the bottom
door of the appliance and set aside.
^ Pull the cover d off.
^ Unscrew the hinge bracket e, rotate
it 180°, then screw it onto the
opposite side.
^ Push the shock absorber arm f as
far as possible towards the handle
side.
^ Turn the plastic cap h 180° and
replace it on the hinge bracket k in
the middle.
^ Loosen the three screws g on the
soft-close mechanism and the
spacer.
^ Now place the cover l on the other
side.
^ In the middle, pry out the housing
with the soft-close mechanism using
a flathead screwdriver.
^ Then, pry the housing with the
soft-close mechanism out of the
retainer from the appliance side.
^ Lay the soft-close mechanism aside.
^ Push out the spacer towards the
hinge side.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ With the assistance of another person,
carefully tilt the appliance backwards
and pull the bearing pin c down and
out.
^ Pay attention to the hinge bushing d.
^ Loosen the screws e and remove the
hinge bracket f.
^ Remove the cover g and loosen the
screw. Attach both to the other side.
^ Screw the hinge bracket f onto the
other side with the two outer screws.
Do not use the middle screw; this
allows later alignment of the appliance
door using the outer, elongated holes!
^ Unscrew the bearing part h from the
hinge bracket f, turn it 180° and
screw it into the opposite hole of the
hinge bracket.
^ Lift the plugs l out of the door
bearing bushing in the appliance
door and place it on the other side.
^ Now place the cover b on the other
side.
Mounting the bottom door of the
appliance:
^ With the assistance of another
person, carefully tilt the appliance
backwards and insert the bearing pin
c into the hinge bracket f from
below. The groove in the bottom of
the hinge bracket faces forwards.
^ Place the hinge bushing d onto the
bearing pin c.
^ Put the cover a on.
^ Place the lower door of the appliance
onto the bearing pin c from above.
^ Remove the cover a towards the
front.
^ Close the bottom door of the
appliance.
^ Pull the cover b off.
^ Screw the adjustment foot at the
bearing pin c completely in.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Hook the spacer on the handle side
into the retainer (A).
^ Put the bearing pin i in the middle
of the appliance through the hinge
bracket k into the bottom door of the
appliance.
^ Hook the soft-close mechanism into
the retainer (B) on the appliance
side.
Push both parts outwards until they
engage.
Mounting the bottom soft-close
mechanism:
^ Remove the cover a from the panel
b, turn it 180° and replace it on the
other side.
^ With the three screws c, first screw
on the spacer on the handle side and
then the soft-close mechanism on the
appliance side.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Mounting the top door of the
appliance:
^ Place the top door of the appliance
onto the bearing pin i in in the
middle of the appliance.
^ Hang the panel b on the shock
absorber arm d.
^ Pull the shock absorber arm d
towards the hinge bracket and insert
the pin e from the top so that the
square rests in the recess.
^ Put on the cover f in such a way
that it engages.
^ Close the top door of the appliance.
^ Put the hinge bracket n on the
opposite side and and fasten it with
the screws m.
Take care that the cover f sits
correctly to ensure that the door closes
properly and the pin is secured.
The screw holes may have to be
pre-punched or use a power
screwdriver.
^ Remove the securing device g.
^ Now place the cover k on the other
side.
^ Align the appliance door with the
appliance housing via the elongated
holes in the bottom hinge bracket .
Tighten the screws.
^ Place the panel b onto the soft-close
mechanism from above, engaging it
at the bottom first and then at the top.
^ Close the bottom door of the
appliance.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Mounting the top soft-close
mechanism:
^ With the three screws c, first screw
on the spacer on the handle side and
then the soft-close mechanism on the
appliance side.
^ Remove the cover a from the panel
b, turn it 180° and replace it on the
other side.
^ Hang the panel b on the shock
absorber arm d.
^ Hook the spacer on the handle side
into the retainer (A).
^ Push the cover e on from the side so
that the openings for the pin f are
on top of each other.
^ Hook the soft-close mechanism into
the retainer (B) on the appliance
side.
^ Pull the shock absorber arm d
towards the hinge bracket and insert
the pin f from the top so that the
square rests in the recess.
Push both parts outwards until they
engage.
^ Then engage the cover e
completely.
Take care that the cover e sits
correctly to ensure that the door closes
properly and the pin is secured.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Remove the securing device g.
The mounting plate c must be
positioned on the door housing in such
a way that when the door is closed the
mounting plate is aligned with the
outside wall of the appliance.
If this alignment is off, you can correct it
by
^ turning both of the pre-mounted set
screws a with a wrench until the
mounting plate c is at the correct
angle.
^ Place the panel b onto the soft-close
mechanism from above, engaging it
at the bottom first and then at the top.
^ Tighten all 4 screws b.
^ From the appliance side, slide the
sidebar d onto the guide for the
mounting plate, until it audibly
engages.
^ Close the top door of the appliance.
Remounting the door handles:
Make sure that the sidebar d does
not come in contact with the door
seal when the door is opened. This
would damage the door seal over
time.
The following instructions must be
followed when attaching the door
handle, otherwise the door seal
could be damaged.
If you see that the sidebar is coming
into contact with the door seal,
^ adjust the mounting plate c again
using the set screws a until the
mounting plate and the sidebar d
are at the correct angle and the
sidebar no longer touches the seal
when the door is opened.
^ First, loosely screw the door handle
onto the opposite side with the two
front screws b.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Aligning the appliance doors
The appliance doors can be aligned
with the appliance housing afterwards.
Align the top door via the elongated
holes in the middle hinge bracket:
In the following figure, the appliance
door is not closed so that the
individual steps can be seen more
clearly.
Align the bottom door in the bottom
hinge bracket via the outer, elongated
holes:
^ Loosen the three screws c slightly.
^ Align the appliance door by moving
the hinge bracket to the right or left.
^ Tighten the screws c.
^ Remove the middle screw a from the
hinge bracket.
^ Loosen the two outer screws b
slightly.
^ Align the appliance door by moving
the hinge bracket to the right or left.
^ Tighten the screws b; the screw a
does not need to be screwed on
again.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
The ventilation cross-sections must
not be blocked or covered in any
way.
They also need to be
dusted/cleaned on a regular basis.
If installing with standard kitchen
cabinets (max. depth 580 mm), the
appliance can be set up directly next to
the kitchen cabinet. In that case the
side of the appliance door would
project 34 mm and the middle of the
appliance 55 mm beyond the front of
the kitchen cabinet. This allows the
appliance door to open and close
properly.
If the appliance is installed next to a
wall d, a gap of at least 55 mm is
needed on the hinge side between the
wall d and the appliance b. This
allows space for the handle when the
door is open.
aadapter cabinet
bappliance
ckitchen cabinet
dwall
The appliance can be installed in any
fitted kitchen. To match the appliance
to the height of the fitted kitchen, a
suitable adapter cabinet a can be
installed over the appliance.
A ventilation gap of at least 2 inches
(50 mm) must be provided between the
adapter cabinet and the kitchen wall.
The ventilation cross-section below the
room ceiling must be at least 46 in2
(300 cm2) so that warm air can escape
without obstruction. Otherwise the
appliance has to work harder, which
results in increased energy
consumption.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Subject to change without notice / 4709
KFN 14943 SD ed
M.-Nr. 07 589 450 / 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|