Operating and installation instructions
Frost free fridge freezer
with PerfectFresh zone
and Dynamic cooling
KFN 14927 SD
KFN 14927 SD ed/cs (-1/-3)
en - GB
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
M.-Nr. 09 436 290
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Storing food in the PerfectFresh zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Humidity level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Storing food in the PerfectFresh zone compartments . . . . . . . . . . . . . . . . . . . . . . 33
Adjusting the interior fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Moving the shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Split shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Adjusting the condiment tray/bottle shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Universal container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Moving the bottle divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Freezing and storing food. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Maximum freezing capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Freezing fresh food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Storing frozen food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Home freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Hints on home freezing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Packing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Before placing food in the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Placing food in the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Freezer calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Ice cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cooling drinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Cool pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Cleaning the interior and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Appliance doors, side panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Ventilation gaps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Door seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Metal grille at the back of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Active charcoal filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
To change the active charcoal filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
After Sales / Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Climate range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Appliances with wall spacers supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Aligning the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Levelling the appliance door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Changing the door hinging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Aligning the appliance doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
aOn/Off sensor for the whole
appliance and On/Off sensor for
switching the refrigerator section on
and off separately
fSensor for switching between the
refrigerator and the freezer sections
(top = "Refrigerator" symbol;
bottom = "Freezer" symbol)
bSuper cool and Super freeze sensor
gSensor for setting a higher
temperature (Y)
cSensor for setting a lower
temperature (X)
hAlarm off sensor
(only visible when the door or
temperature alarm sounds)
dSafety lock indicator light
(only visible when the Safety lock is
activated)
iChange active charcoal filter
indicator
eTemperature display for the
refrigerator and freezer sections
(only visible when the active
charcoal filters need to be changed)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
aDynamic cooling fan
bAdjustable shelves
cPerfectFresh zone compartments
dControl for setting the humidity in the
PerfectFresh zone compartments
eButter and cheese compartment
fEgg tray/Condiment tray/Universal
container
gActive charcoal filter holder
hBottle rack
iBottle divider
jBottle shelf
kCondensate channel and
drain hole
lFreezer drawers with
freezer calendar
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
Take care not to damage the pipework
at the back of it before or during
transportation to an authorised
collection depot.
In this way, refrigerant in the pipework
and oil in the compressor will be
contained, and will not leak out into the
environment.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This appliance complies with all relevant safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before installation and
before using it for the first time. They contain important
information on its safety, installation, use and maintenance. Miele
cannot be held liable for damage caused by non-compliance with
these Warning and Safety instructions.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
The appliance is not designed for commercial use. It is intended
~
for use in domestic households and similar working and residential
environments.
This appliance is not intended for outdoor use.
The appliance must only be used as a domestic appliance to
~
cool and store food as well as to store deep frozen food, freeze
fresh food and to prepare ice.
Any other usage is not supported by the manufacturer and could be
dangerous.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
The appliance is not suitable for storing and keeping cool
~
medicines, blood plasma, laboratory preparations or other such
materials or products. Incorrect use of the appliance for such
purposes can cause deterioration of the items stored. The appliance
is not suitable for use in areas where there is a risk of explosion.
Miele cannot be held liable for damage resulting from incorrect or
improper use or operation.
The appliance can only be used by people with reduced
~
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and understand the hazards
involved.
Safety with children
Children under 8 years of age must be kept away from the
~
appliance unless they are constantly supervised.
Children 8 years and older may only use the appliance without
~
supervision if they have been shown how to use it in a safe way and
understand the hazards involved.
Children must not be allowed to clean or maintain the appliance
~
unsupervised.
This appliance is not a toy! To prevent the risk of injury, do not
~
allow children to play with it or use the controls. Please supervise
children whilst you are using the appliance.
Danger of suffocation. Packaging, e.g. cling film, polystyrene and
~
plastic wrappings, must be kept out of the reach of babies and
children. Whilst playing, children could become entangled in
packaging or pull it over their head and suffocate.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Before setting up the appliance, check it for any externally visible
~
damage. Do not install and use a damaged appliance.
It could be dangerous.
If the connection cable is faulty it must only be replaced by a service
~
technician authorised by the manufacturer to protect the user from
danger.
This appliance contains the coolant Isobutane (R600a), a natural
~
gas which is environmentally friendly. Although it is flammable, it
does not damage the ozone layer and does not increase the
greenhouse effect. The use of this coolant has, however, led to a
slight increase in the noise level of the appliance. In addition to the
noise of the compressor, you might be able to hear the coolant
flowing around the system. This is unavoidable, but does not have
any adverse effect on the performance of the appliance.
Care must be taken during the transportation and installation of the
appliance that no parts of the cooling system are damaged. Leaking
coolant can damage the eyes.
In the event of any damage:
- avoid open flames and anything which creates a spark,
- disconnect from the mains,
- air the room in which the appliance is located for several minutes
and
- contact the Service Department for advice.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
The more coolant there is in an appliance, the larger the room it
~
should be installed in. In the event of a leakage, if the appliance is in
a small room, there is the danger of combustible gases building up.
For every 8 g of coolant at least 1 m3 of room space is required. The
amount of coolant in the appliance is stated on the data plate inside
the appliance.
Safe operation of the appliance is only assured if it has been
~
installed and connected in accordance with these operating and
installation instructions.
Before connecting the appliance, make sure that the connection
~
data on the data plate (voltage and frequency) matches the mains
electricity supply.
This data must correspond in order to avoid the risk of damage to
the appliance. Consult a qualified electrician if in any doubt.
Do not connect the appliance to the mains electricity supply by a
~
multi-socket adapter or an extension lead. These do not guarantee
the required safety of the appliance (e.g. danger of overheating).
The electrical safety of this appliance can only be guaranteed
~
when it is correctly earthed. It is most important that this basic safety
requirement is observed and regularly tested and where there is any
doubt, the household wiring system should be inspected by a
qualified electrician.
The manufacturer cannot be held liable for damage or injury caused
by the lack of or inadequacy of an effective earthing system (e.g.
electric shock).
Installation, maintenance and repairs may only be carried out by
~
a suitably qualified and competent person in strict accordance with
current national and local safety regulations.
Repairs and other work by unqualified persons could be dangerous.
The manufacturer cannot be held liable for unauthorised work.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
While the appliance is under guarantee, repairs should only be
~
undertaken by a service technician authorised by the manufacturer.
Otherwise the guarantee will be invalidated.
The appliance must be isolated from the electricity supply during
~
installation, maintenance and repair work.
Faulty components must only be replaced by genuine Miele
~
original spare parts. The manufacturer can only guarantee the safety
of the appliance when Miele replacement parts are used.
This appliance must not be used in a non-stationary location (e.g.
~
on a ship).
In areas which may be subject to infestation by cockroaches or
~
other vermin, pay particular attention to keeping the appliance and
its surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the guarantee.
The manufacturer cannot be held liable for damage caused by a
~
faulty connection to the mains water supply.
Connection to the mains water supply and any repairs to the ice
~
cube maker must only be carried out by a suitably qualified and
competent person.
The ice cube maker is not suitable for connection to a hot water
~
supply.
Before plumbing the appliance in, ensure that it is disconnected
~
from the mains electricity supply.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct use
Never handle frozen food with wet hands. Your hands may freeze
~
to the frozen food. Danger of frost burn.
Do not take ice cubes out with your bare hands and never place
~
ice cubes or ice lollies in your mouth straight from the freezer.
The very low temperature of the frozen ice or lollies can cause frost
burn to the lips and tongue.
Do not refreeze partially or fully defrosted food. Consume
~
defrosted food as soon as possible, as it will lose its nutritional value
and spoil if left for too long. Defrosted food may only be re-frozen
after it has been cooked.
Do not store explosive materials in the appliance or any products
~
containing propellants (e.g. spray cans). Thermostats switching on
may produce sparks which could present a fire hazard. Flammable
compounds could explode.
Do not operate any electrical equipment (e.g. an electric
~
ice-cream maker) inside the appliance. Danger of sparking and
explosion.
If storing alcohol with a high percentage proof in the refrigerator,
~
make sure it is tightly closed and stored upright.
Danger of explosion.
Do not store cans or bottles containing carbonated drinks or
~
liquids which could freeze in the freezer. The cans or bottles could
explode. Danger of injury and damage to the appliance.
When cooling drinks quickly in the freezer, make sure bottles are
~
not left in for more than one hour; otherwise they could burst,
resulting in injury or damage.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Observe the "use-by" dates given on food to avoid the risk of food
~
poisoning.
Storage times will depend on several factors, including the
freshness and quality of the food as well as the temperature at which
it is stored. Follow the instructions given on the food manufacturer's
packaging regarding storage conditions and "use-by" dates.
Do not use sharp edged objects to
~
– remove frost and ice,
– separate frozen foods and remove ice trays.
They will damage the evaporator, causing irreversible damage to
the appliance.
Do not place electric heaters or candles in the appliance to
~
defrost it. These will damage the plastic parts.Do not use defrosting
sprays or de-icers, as they might contain substances which could
damage the plastic parts or which could cause the build-up of
gases and pose a danger to health.
Do not use a steam-cleaning appliance to defrost or clean this
~
appliance. Steam could reach electrical components and cause a
short circuit.
Do not use any oils or grease on the door seals, as these will
~
cause the seals to deteriorate and become porous with time.
If storing food which contains a lot of fat or oil in the appliance or
~
the refrigerator door, make sure it does not come into contact with
plastic components as this could cause stress cracks.
Do not block the ventilation gaps in the appliance as this would
~
impair the efficiency of the appliance, increase the electricity
consumption and could cause damage to the appliance.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This appliance is designed for use within certain climate ranges
~
(ambient temperatures), and should not be used outside this range.
The climate range for your appliance is stated on the data plate
inside the appliance.
Installing it in a room with too low an ambient temperature, e.g. a
garage, can lead to the appliance switching off for longer periods so
that it cannot maintain the required temperature.
Stainless steel appliances
Do not use sticky notes, transparent adhesive tape, masking tape
~
or other types of adhesive on the surface of the door. These
damage the surface, causing it to lose its dirt-repellent protective
coating.
The high-quality surface of the door is susceptible to scratching.
~
Even fridge magnets can cause scratching.
Disposal of your old appliance
Before disposing of an old appliance, first make the door latch or
~
lock unusable.
This way you will prevent children from accidentally locking
themselves in and endangering their lives.
Be careful not to damage any part of the pipework whilst awaiting
~
disposal, e.g. by
– puncturing the refrigerant channels in the evaporator.
– bending any pipework.
– scratching the surface coating.
Splashes of refrigerant can damage the eyes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
How to save energy
Normal energy
Increased energy
consumption
consumption
Installation site
In a ventilated room.
In an enclosed, unventilated
room.
Protected from direct
sunlight.
In direct sunlight.
Not near to a heat source
(radiator, oven).
Near to a heat source
(radiator, oven).
Where the ideal ambient room Where there is a high
temperature is approx. 20°C. ambient room temperature.
Ventilation gaps uncovered Ventilation gaps covered or
and dusted regularly.
dusty.
Compressor and metal grille Dust build-up on the
(heat exchanger) dusted at compressor and metal grille
least once a year. (heat exchanger).
Temperature
setting
Refrigerator section 4 to 5 °C With a higher setting: the
lower the temperature, the
Freezer section -18 °C
higher the energy
consumption.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
How to save energy
Normal energy consumption Increased energy
consumption
Use
Drawers, shelves and racks
arranged as they were when
the appliance was delivered.
Only open the doors when
necessary and for as short a
time as possible.
Frequent opening of the door
for long periods will cause a
loss of coldness. The
appliance works harder to
cool down and the
Store food in an organised
way.
compressor runs for longer
periods.
Take an insulated cool bag
with you when shopping and
Hot food or food at room
temperature raises the
place food in the appliance as temperature inside the
soon as possible.
appliance. The appliance
works harder to cool down
and the compressor runs for
longer periods.
Replace any food removed
rapidly, before it begins to
thaw.
Allow hot food and drinks to
cool down before placing
them in the appliance.
Store food covered or
packaged.
The evaporation or
condensation of liquids will
cause a loss of coldness in the
refrigerator.
Place frozen food in the
refrigerator to defrost.
Do not over-fill the appliance
to allow air to circulate.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching on and off
Before using for the first time
Active charcoal filters
(Active Air Clean charcoal filters)
Protective foil
^ Place the active charcoal filters
supplied in the holder, and place the
holder on one of the refrigerator
shelves (see "Active charcoal filters").
The stainless steel trim to the interior
shelves and the door shelves has a
layer of protective foil to prevent
damage during transportation.
On stainless steel appliances, the outer
surfaces are also covered with
protective foil.
Operating the appliance
A light touch of the finger on the
sensors is all that is required to operate
this appliance.
^ Do not remove the foil until the
appliance has been positioned in its
final location.
Switching on
The refrigerator section/PefectFresh
zone and freezer section are switched
on together with the On/Off sensor.
Cleaning and care
^ Treat the stainless steel trim to the
interior shelves and the door shelves
with the Miele stainless steel
conditioner supplied as soon as you
have removed the foil.
^ On stainless steel appliances also
treat the side panels with the Miele
stainless steel conditioning agent
supplied as soon as you have
^ Touch the On/Off sensor until the
temperature display lights up.
The temperature display for the
removed the protective foil.
refrigerator section will show the current
temperature in the refrigerator section.
The appliance doors have a special
finish which is resistant to soiling. Do
not use Miele stainless steel
If the temperature in the freezer section
is above 0 °C, only bars will light up in
the temperature display for the freezer
section. As soon as the temperature is
below 0 °C, the temperature display for
the freezer section will show the current
temperature in the freezer section.
conditioner on the appliance door.
Important. Each time it is used, the
Miele stainless steel conditioning
agent forms a water and dirt repellent
protective coating.
The "Freezer" symbol and the Alarm off
sensor will flash until the temperature in
the freezer section has cooled down to
the correct temperature for freezing.
^ Clean the inside of the appliance and
the accessories with lukewarm water
and a little washing up liquid, and then
dry with a soft cloth.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching on and off
The appliance will start to cool, and the Please refer to the relevant section for
interior lighting will come on when the
refrigerator section door is opened.
more information.
Cool pack
To enable the temperature to get
sufficiently cold inside the
appliance, allow the appliance to
run for a few hours before placing
food in it.
Place the cool pack in the top freezer
drawer. The cool pack will be at its
most effective after it has been in the
freezer for approx. 24 hours.
Do not place food in the freezer
section until the temperature is at
least -18°C.
Switching off
^ Touch the On/Off sensor until all of
the indicators go out. (If this does not
happen, the safety lock is still
activated).
You switch between the refrigerator and
freezer sections with this sensor.
If the refrigerator section is switched
on, the refrigerator section and freezer
section will switch off one after the
other.
If you want to select the freezer section
(to check the temperature, for
example),
The interior light will not come on when
you open the door and the cooling
process will be switched off.
^ touch the sensor for switching
between the refrigerator and freezer
section until the "Freezer" symbol
lights up yellow.
Depending on which section you have
selected, you can
– select either Super cool or Super
freeze, or
– adjust the temperature.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching on and off
To switch the refrigerator
section/PerfectFresh zone off
separately
then touch the On/Off sensor until the
temperature display lights up, or
^ Switch the appliance off and then
back on again.
The refrigerator section/PerfectFresh
zone can be switched off without
having to switch off the freezer section.
This is useful e.g. whilst on holiday.
The appliance will start to cool, and the
interior lighting will come on when the
refrigerator section door is opened.
Settings mode
Certain settings on the appliance can
only be selected in settings mode.
How to select settings mode and how
to change the settings is described in
the relevant section of these
instructions.
^ Switch the appliance on and select
the refrigerator section.
The "Refrigerator" symbol will light up
yellow.
Overview of functions that can be
selected in settings mode:
To enter or leave settings mode c
^ Touch the On/Off sensor until the
To switch the sensor tone on/off b
(see "Switching on and off")
"Refrigerator" symbol goes out.
The interior light will not come on when
you open the door and the refrigerator
section is switched off.
To confirm that the active
charcoal filters have been
changed (see "Active charcoal
filters")
^
The freezer section remains switched
on and the "Freezer" symbol is lit up.
To switch the safety lock on/off
(see "Switching on and off")
u
To switch the refrigerator
section/PerfectFresh zone back on
again
To change the brightness of the d
temperature display
(see "The correct temperature")
To adjust the temperature in the
PerfectFresh zone
§
(see "The correct temperature")
^ Select the refrigerator section. The
"Refrigerator" symbol lights up yellow,
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching on and off
^ Touch the On/Off sensor to confirm a
The door alarm is automatically
disabled when the appliance is in
settings mode. As soon as the door is
closed, the door alarm is activated
again.
new setting.
^ Touch the X sensor repeatedly until c
appears in the display.
^ Touch the On/Off sensor.
You have now left settings mode.
Switching the sensor tone on/off
The sensor tone which sounds each
time a sensor is touched can be
deactivated.
Activating or deactivating the safety
lock
The safety lock can be activated to
prevent the appliance being switched
off inadvertently.
^ Touch and leave your finger on the X
sensor.
^ Touch and leave your finger on the X
sensor.
^ At the same time, briefly touch the
On/Off sensor (without letting go of
the X sensor).
^ At the same time, briefly touch the
On/Off sensor (without letting go of
the X sensor).
^ Leave your finger on the X sensor for
another 5 seconds until c appears in
the display.
^ Leave your finger on the X sensor for
another 5 seconds until c appears in
the display.
^ Touch the X sensor repeatedly until b
appears in the display.
^ Touch the On/Off sensor.
^ Touch the X sensor repeatedly until u
appears in the display.
^ By touching the V sensor, you can
now select whether the sensor tones
are switched on or off:
^ Touch the On/Off sensor.
^ By touching the X sensor, you can
now select whether the safety lock is
switched on or off:
b 0: The sensor tones are deactivated
b 1: The sensor tones are activated
b -: Return to menu
u 0: The safety lock is deactivated
u 1: The safety lock is activated
u –: Return to menu.
The old setting lights up, and your
newly selected setting flashes.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Switching on and off
The old setting lights up, and your
newly selected setting flashes.
^ Touch the On/Off sensor to confirm a
new setting.
^ Touch the X sensor repeatedly until c
appears in the display.
^ Touch the On/Off sensor.
You have now left settings mode.
The safety lock indicator X will light up
in the temperature display when the
safety lock has been activated.
Switching off for longer
periods of time
If the appliance is not going to be used
for a longer period of time, e.g. whilst
on holiday:
^ switch the appliance off,
^ disconnect it from the mains,
^ clean the appliance out and
^ leave the doors ajar to air the
appliance.
If, during a long absence, the
appliance is switched off but not
cleaned out and the doors are left
shut, there is a danger of mould and
odours building up inside the
appliance.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The correct temperature
It is very important to set the correct
temperature for storing food in the
appliance. Micro-organisms will cause
food which is not stored at the correct
temperature to deteriorate rapidly.
Temperature influences the growth rate
of these micro-organisms. Reducing
the temperature reduces their growth
rate.
Dynamic cooling
The dynamic cooling fan automatically
switches on when the cooling system
for the refrigerator switches on. It
distributes the temperature in the
appliance to all areas evenly so that all
the food will be chilled to about the
same degree.
The temperature in the appliance will
rise:
. . . in the freezer section
To freeze fresh food and to store frozen
food for a long time, a temperature of
-18 °C is required. At this temperature
the growth of micro-organisms is
generally halted. As soon as the
– the more often the door is opened
and the longer it is kept open,
– the more food that is stored in it,
– the warmer the food is which is being
put into it,
temperature rises above -10 °C, the
micro-organisms become active in the
food again so that it cannot be kept as
long. For this reason, partially defrosted
or defrosted food must not be re-frozen.
Food may be re-frozen once it has
been cooked, as the high temperatures
achieved when cooking destroy most
micro-organisms.
– the higher the ambient temperature
surrounding the appliance.
The appliance is designed for use in
specific ambient temperatures
(climate ranges). Do not use in
ambient temperatures for which it is
not designed.
. . . in the refrigerator and the
PerfectFresh zone
We recommend a temperature of 4 °C
in the middle of the refrigerator.
The temperature in the PerfectFresh
zone is controlled automatically, and is
maintained at 0 to 3 °C.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
The correct temperature
Setting the temperature
– Leaving a finger on the sensor:
changes the temperature
continuously.
The temperatures in the refrigerator
section/PrefectFresh zone and freezer
section are set independently of one
another.
When the highest or lowest
temperature in the range is reached,
the X or Y sensor disappears.
Approx. 5 seconds after taking your
finger off a sensor, the average,
current temperature of the refrigerator
or freezer section is automatically
shown.
^ Select the refrigerator or the freezer
If you have adjusted the temperature,
wait for approx. 6 hours if the
appliance is not very full and for
approx. 24 hours if the appliance is
full before checking the temperature
display, as it will take this long for the
display to give an accurate reading. If,
after this time, the temperature is still
too high or too low, you will need to
adjust it again.
section.
The "Refrigerator" symbol or the
"Freezer" symbol will light up yellow.
^ You can now use the arrow sensors
on either side of the temperature
display to set the temperature you
require.
Temperature range
The temperature can be adjusted:
By touching the
– In the refrigerator section from 4 °C
to 9 °C
X sensor: the temperature will get
colder
– In the freezer section from -16 °C to
-26 °C
Y sensor: the temperature will get
warmer.
The ambient temperature in the room
and the installation location can affect
the time it takes for the appliance to
reach the lowest temperature. If the
ambient temperature is too high, the
appliance may not reach the lowest
temperature.
The temperature being set will flash in
the display.
The following information shows in the
display when the sensors are touched:
– Touching a sensor once: the last
temperature selected flashes.
– Each subsequent touch of a sensor:
adjusts the temperature shown in
1 °C steps.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
The correct temperature
Temperature display
^ You can now adjust the temperature
in the PerfectFresh zone by touching
the X sensor. You can choose from
settings 1 to 9:
§ 1: Lowest temperature,
§ 9: Highest temperature.
§ –: Return to menu.
During normal operation the
temperature display on the control
panel shows the temperature in the
middle of the refrigerator section or the
temperature in the warmest part of the
freezer section.
The old setting lights up, and your
newly selected setting flashes.
Setting the temperature in the
PerfectFresh zone
^ Touch the On/Off sensor to confirm a
new setting.
The temperature in the PerfectFresh
zone is automatically held at 0 to 3 °C.
It can be raised or lowered, e.g. if you
want to use it for storing items like fish.
^ Touch the X sensor repeatedly until c
appears in the display.
^ Touch the On/Off sensor.
You have now left settings mode.
§ 5 is the default setting for the
PerfectFresh zone. If a setting of § 1
to § 4 is selected, the temperature
can fall below 0°C. Food could
freeze!
^ Touch and leave your finger on the X
sensor.
^ At the same time, briefly touch the
On/Off sensor (without letting go of
the X sensor).
^ Leave your finger on the X sensor for
another 5 seconds until c appears in
the display.
^ Touch the X sensor repeatedly until §
appears in the display.
^ Touch the On/Off sensor.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
The correct temperature
Changing the temperature display
brightness
^ Touch the On/Off sensor.
You have now left settings mode.
The temperature display brightness can
be adjusted to suit the lighting
conditions of the room.
^ Touch and leave your finger on the X
sensor.
^ At the same time, briefly touch the
On/Off sensor (without letting go of
the X sensor).
^ Leave your finger on the X sensor for
another 5 seconds until c appears in
the display.
^ Touch the X sensor repeatedly until d
appears in the display.
^ Touch the On/Off sensor.
^ The temperature display brightness
can now be changed by touching the
X sensor:
d 0: Maximum brightness
d 1: Reduced brightness
d –: Return to menu.
The old setting lights up, and your
newly selected setting flashes.
^ Touch the On/Off sensor to confirm a
new setting.
^ Touch the X sensor repeatedly until c
appears in the display.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm
Your appliance has been fitted with a
warning system which ensures that the
temperature in the freezer section
cannot rise unnoticed and to avoid
energy being wasted if a door is left
open.
Switching the temperature
alarm off early
If the noise disturbs you, you can
switch the alarm off early if you wish.
Activating the alarm system
The alarm system is always active. It
does not have to be switched on
manually.
^ Touch the alarm off sensor.
The alarm will stop.
The alarm off sensor and the freezer
symbol will continue to flash until the
correct temperature has been
reached.
Temperature alarm
An alarm will sound if the temperature
in the freezer section becomes too
warm.
However, if the temperature in the
freezer section remains above
-18 °C for a long time, check that the
frozen food has not started to
defrost. If it has, check that the food
is safe to use and if it is, then use it
as soon as possible.
The alarm off sensor will flash red and
the "Freezer" symbol will flash.
The alarm will sound, the alarm off
sensor will flash red and the freezer
symbol will flash, for example,
– if a lot of room air enters the freezer
section when food is being loaded,
rearranged or taken out.
– when freezing large amounts of food
at once.
– when freezing food which is still
warm.
– in the event of a power cut.
The alarm will stop and the symbols will
go out as soon as the temperature has
dropped down to the correct level
again.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm
Door alarm
The alarm will sound if a door is left
open for more than approx. 2 minutes.
The alarm off sensor will light up red
and the symbol for the section which
has the opened door will flash.
The alarm will stop and the symbols will
go out as soon as the door is closed.
Switching the door alarm off
early
If the noise of the door alarm disturbs
you, you can switch it off early if you
wish.
^ Touch the alarm off sensor.
The alarm will stop.
The alarm off sensor will light up
constantly and the symbol for the
section which has the opened door
will continue to flash until the door
has been closed.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Super cool and Super freeze
Super cool
Switching off Super cool
The Super cool function can be used to The Super cool function will switch itself
rapidly reduce the temperature in the
refrigerator to its lowest setting
off automatically after approx. 6 -
12 hours. The appliance will then
continue to work at normal power.
(depending on the room temperature).
To save energy, the Super cool function
can be switched off once food and
drinks are sufficiently chilled.
Switching on Super cool
Super cool is particularly
recommended for the faster chilling of
large amounts of fresh food or drink.
^ Select the refrigerator section.
The "Refrigerator" symbol will light up
yellow.
^ Select the refrigerator section.
The "Refrigerator" symbol will light up
yellow.
^ Touch the Super cool sensor. It will
dim to a pale yellow colour.
The appliance will continue running at
normal power.
^ Touch the Super cool sensor. It will
light up yellow.
The appliance will then work at full
power to lower the temperature in the
refrigerator section.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Super cool and Super freeze
Super freeze
power to lower the temperature in the
freezer section.
Switch the Super freeze function on
before putting fresh food into the
freezer section.
Switching off Super freeze
Depending on the amount of food
placed in the freezer section, the Super
freeze function will switch off
This helps food to freeze quickly and
retain its nutrients, vitamins, flavours
and appearance.
automatically after approx. 30 to 65
hours. The appliance will then continue
to work at normal power.
Super freeze is not necessary:
– when placing food in the freezer that
is already frozen.
To save energy, the Super freeze
function can be switched off once a
constant temperature of -18 °C or
colder has been reached in the freezer
section.
– when freezing up to 2 kg fresh food
daily.
Switching on Super freeze
When freezing small quantities of food
in the freezer, the Super freeze function
should be switched on 6 hours
beforehand. When freezing the
maximum load of food the Super
freeze function should be switched on
24 hours beforehand.
^ Select the freezer section.
The "Freezer" symbol will light up
yellow.
^ Touch the Super freeze sensor. It will
^ Select the freezer section.
dim to a pale yellow colour.
The "Freezer" symbol will light up
yellow.
The appliance will continue running at
normal power.
^ Touch the Super freeze sensor. It will
light up yellow.
The appliance will then work at full
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing food in the refrigerator section
Different storage zones
– pre-packed vegetables and other
fresh food with a label stating it
should be kept at a temperature of
approx. 4 °C.
Due to the natural circulation of the air
in the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
the different zones when placing food
in the appliance.
Do not store explosive materials in
the appliance or any products
containing propellants (e.g. spray
cans). Danger of explosion.
This appliance has automatic
dynamic cooling, which helps to
keep an even temperature when the
fan is running, making the difference
between the various zones less
pronounced.
If storing alcohol with a high
percentage proof, make sure it is
tightly closed, and store upright.
If storing food which contains a lot of
fat or oil in the refrigerator or the
refrigerator door, make sure that it
does not come into contact with
plastic components as this could
cause stress cracks.
Warmest area
The warmest area is in the top section
of the door. Use this for storing butter
and cheese.
Food must not touch the back wall of
the refrigerator, as it may freeze to
the back wall.
Coldest areas
The coldest areas in the refrigerator
section are directly above the
PerfectFresh zone and in the
PerfectFresh zone itself which is slightly
colder still.
To allow air to circulate efficiently,
do not pack food too closely
together in the refrigerator. Do not
cover the fan in the rear wall of the
refrigerator, as this is essential for
keeping the appliance cool.
Use these areas for all delicate and
highly perishable food, e.g.
– fish, meat, poultry,
– sausage products, ready meals,
– dishes or baked goods containing
eggs or cream,
– fresh dough, cake mixtures, pizza or
quiche dough,
– soft cheese and other dairy
products,
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing food in the refrigerator section
Food which is not suitable for
storing in the refrigerator
refrigerator can cause food to start
deteriorating.
Not all food is suitable for storing in a
refrigerator at temperatures below 5 °C,
as some food is sensitive to cold.
Storing food correctly
Food should generally be stored
Cucumbers, for example, become
glassy, aubergines bitter and potatoes
covered or packaged in the refrigerator
(there are some exceptions to this rule
sweet. Tomatoes and oranges lose their in the PerfectFresh zone - see below).
aroma, and the peel on citrus fruits
hardens.
This will prevent food smells from
affecting other food, food from drying
out, and also any cross-contamination
of bacteria. The growth of bacteria,
such as salmonella, can be avoided by
setting the correct temperature and
maintaining good standards of hygiene.
Food which is sensitive to cold
includes:
– Pineapples, avocados, bananas,
pomegranates, mangos, melons,
papayas, passion fruit,
citrus fruit (such as lemons, oranges,
mandarins, grapefruit),
Unpacked meat and vegetables
Unpackaged meat and vegetables
should be stored separately. To avoid
any microbiological
– Fruit which is not yet ripe
– Aubergines/egg plant, cucumbers,
potatoes, peppers/capiscum,
cross-contamination, these foods may
only be stored together if they are
wrapped.
tomatoes, courgettes/zucchini,
– Some hard cheeses, e.g. Parmesan
When shopping for food
The freshness of food when first placed
in the appliance is an important factor
in determining how long it stays fresh,
and how long it can be kept in the
refrigerator. Always observe the use-by
date and recommended storage
temperature.
Time out of the refrigerator, e.g. during
transportation, should be kept to a
minimum. For example, do not allow
food to stay in a hot car for too long.
Once food has started to deteriorate,
this process cannot be reversed. As
little as two hours outside the
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing food in the PerfectFresh zone
Food is stored at a lower temperature in longer period, as the water content of
the PerfectFresh zone than in the
refrigerator section. The humidity in the
PerfectFresh zone compartments can
also be regulated to suit the food being
stored, providing ideal storage
the food is largely retained.
Storing food in the
PerfectFresh zone
compartments
conditions and ensuring that food stays
fresh considerably longer while
You can adjust the relative humidity in
the PerfectFresh compartment with the
regulator.
retaining both flavour and vitamins.
Storage temperature
Slide the regulator to the relative
humidity level required.
The optimum storage temperature for
fresh food which is not sensitive to cold
is 0 - 3 °C. This is the temperature
range which is automatically
. = high humidity. The regulator
closes the vents to the compartment
and retains the moisture already
present. The humidity level greatly
depends on the type and quantity of
food being stored.
maintained in the PerfectFresh zone.
Food can be stored there at this
temperature without loss of freshness
for considerably longer than in a stan-
dard refrigerator, as the deterioration
process is decelerated at this
Please take into account that high
humidity is only achieved and effective
if the food is stored unwrapped or
loosely wrapped.
temperature.
– The high humidity setting . is ideal
for storing freshly harvested produce
such as vegetables, salad, herbs,
cabbage and home-grown seasonal
fruit.
Remember that the fresher the food
when placed in the appliance, the
longer it will stay fresh.
Humidity level
The humidity level in the PerfectFresh
compartment will depend on
– the moisture content of the food
being stored and
– the quantity of food being stored.
Use the regulator to adjust the humidity
level in the PerfectFresh compartment.
The closer the storage humidity is to the
humidity content of the food, the crisper
and fresher the food remains over a
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing food in the PerfectFresh zone
, = low humidity.
Can all types of food be stored
The regulator opens the vents to the
compartment to allow the moisture to
escape.
together?
Do not place all types of food together
in one compartment. Some types of
food do not store well together. Aromas
and flavours can transfer from one type
of food to another (e.g. carrots absorb
the smell and flavour of onions very
easily). Some food also gives off a
natural gas (ethylene) which speeds up
the rate at which other food perishes.
If the regulator is set at low humidity ,,
the humidity will be approx. the same
as the humidity in the refrigerator
section. At this setting, the low
temperature is the main advantage of
the compartment rather than the
humidity.
– With low humidity , selected, the
PerfectFresh compartment is ideal
for storing particularly sensitive
foods, such as fresh fish, shellfish,
meat, poultry, sausages, dairy
products and salad.
Examples of fruit and vegetables
which produce a large amount of this
natural gas are:
Apples, apricots, pears, nectarines,
peaches, plums, avocados, figs,
blueberries, melons and beans.
Please note that foods rich in protein
deteriorate faster than others.
Shellfish, for example, deteriorates
faster than fish, and fish deteriorates
faster than meat.
Examples of fruit and vegetables
which react strongly to the natural
gases given off by other types of fruit
and vegetables are:
Always keep these foods covered or
wrapped.
Kiwis, broccoli, cauliflower, Brussels
sprouts, mangos, honeydew melons,
apples, apricots, cucumbers, tomatoes,
pears, nectarines and peaches.
Exception: Meat. The surface of the
meat dries out slightly, helping to
prevent the growth of bacteria, which
results in the meat lasting longer. To
prevent the risk of bacterial
Example: Broccoli should not be stored
with apples, as apples produce a large
amount of natural gas to which broccoli
is very sensitive. The result is a shorter
than expected storage time for the
broccoli.
cross-contamination and meat
deteriorating, do not let one type of
meat come into direct contact with
another type.
Take food out of the PerfectFresh
zone approx. 30 - 60 minutes before
using it. The aroma and taste do not
fully develop until the food has
reached room temperature.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing food in the PerfectFresh zone
The following tips may help if you find that food you have stored does not
keep well (e.g. food becomes limp or wilts after only being stored for a short
time):
^ Only use the appliance for storing fresh food. The condition of the food when it
is first placed in the appliance is an important factor in determining how long it
stays fresh.
^ Clean food before placing it in the PerfectFresh zone.
^ Allow very moist food to drain before placing it in the PerfectFresh zone.
^ Do not store food which is sensitive to cold in the PerfectFresh zone
(see "Food which is not suitable for storing in the refrigerator")
^ Bear in mind that not all types of food can be stored together (see "Can all types
of food be stored together?").
^ Select the correct PerfectFresh compartment (high or low humidity).
^ Store food unwrapped in the high humidity PerfectFresh compartment.
High humidity in the PerfectFresh compartment can only be achieved by storing
food which contains moisture in it.
If the humidity is not high enough, because, for example, too little food has been
stored in the compartment, you can use a wet sponge to increase the humidity.
^ If you think that the temperature in the PerfectFresh zone is too high or too low,
try regulating it via the refrigerator section by altering the temperature of the
refrigerator section slightly by 1 to 2 °C.
The temperature must be increased if ice crystals start to form on the floor of the
PerfectFresh zone as otherwise the cold temperature will damage the food.
^ If a lot of water has gathered on the base of the PerfectFresh zone, dry the base
with a towel. Drain food before storage or place a rack on the floor of the
PerfectFresh zone and place the food on the rack so that the moisture can drip
down.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the interior fittings
Moving the shelves
To move the split shelf:
The shelves can be adjusted according ^ Take both halves of the split glass
to the height of the food.
shelf out,
^ Raise the shelf, and pull it forwards
slightly until the notch at the side is in
line with the shelf support. It can then
be raised or lowered to the required
level.
The raised edge at the back must face
upwards to prevent food from touching
the back of the appliance and freezing
to it.
^ fit the two brackets onto the supports
on either side at the required height,
Stoppers prevent the shelves from
being dislodged by mistake.
^ and push the glass shelves in one
after the other. The shelf with the
raised edge must be at the back.
Split shelf
In order to accommodate tall items in
the appliance, one of the shelves is
divided. The front section can be
pushed under the rear section.
^ Push the rear half of the glass shelf
up slightly from below.
^ At the same time, pull the front half of
the glass shelf forwards slightly and
then push it carefully under the rear
half.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the interior fittings
PerfectFresh zone
compartments
Adjusting the condiment
tray/bottle shelf
The compartments in the PerfectFresh
zone are on telescopic rails, and can
be removed for filling, emptying or
cleaning purposes.
^ Lift the tray/shelf up and out of the
stainless steel frame to remove.
^ Push up the stainless steel frame,
and remove.
^ Pull out the compartment as far as it
^ Replace the frame at the required
height. Ensure that it is securely
pushed back into position.
will go, and then lift it up and out.
Push the runners back in again to
avoid injury or damage.
^ Carefully pull out the lid between the
compartments slightly, and lift it
down and out.
^ To replace it, insert the compartment
lid from beneath into the holders, and
push it back into place.
To replace the compartment,
^ Some stainless steel frames are
easier to remove and replace if you
put your hand behind the back bar of
the frame and lift it upwards.
^ Replace the tray/shelf in the frame.
The tray/shelf can be removed
completely and used as a serving tray
at the table.
^ place it back on the fully extended
runners a. The front of the runners
must be right up against the front of
the compartment b.
^ Then push the compartment back in
c.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the interior fittings
Universal container
Moving the bottle divider
(depending on model)
The bottle divider can be moved to the
left or right to ensure that bottles are
held securely in position when the door
is opened and shut.
The universal container can be used
both to store and serve food.
The bottle divider can be removed
completely (e.g. for cleaning).
^ To do this, push up the front edge of
the bottle divider, and disengage it.
It consists of a deep tray a and a
shallow tray b. Both trays fit the
stainless steel frame.
If you wish to use the universal
container to serve food,
^ place the shallow tray b in the
stainless steel frame, and use the
deep tray as a lid a.
You can lift the universal container,
including contents, out of the frame and
take it to the table.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing and storing food
Maximum freezing capacity
Storing frozen food
To ensure that fresh food placed in the
freezer freezes through to the core as
quickly as possible, the maximum
freezing capacity must not be
When buying frozen food to store in
your freezer, check
– that the packaging is not damaged,
– the use-by date,
exceeded. The maximum freezing
capacity for freezing within a 24-hour
period is given on the data plate:
"Freezing capacity ....kg/24 hrs".
– the temperature at which the frozen
food is being stored in the shop. The
length of time it can be kept is
The maximum capacity quoted is
calculated in accordance with DIN EN
ISO 15502.
reduced if it has been stored at a
temperature warmer than -18 °C.
^ Buy frozen food once you have
finished the rest of your shopping,
and wrap it in newspaper or use a
cool bag or cool box to transport it.
Freezing fresh food
Fresh food should be frozen as quickly
as possible. This way the nutritional
value of the food, its vitamin content,
appearance and taste are not impaired.
^ Store it in the freezer as soon as
possible.
Never re-freeze partially or fully
defrosted food. Consume defrosted
food as soon as possible as it will
lose its nutritional value and spoil if
left for too long. Defrosted food may
only be re-frozen after it has been
cooked.
Food which takes a long time to freeze
will lose more water from its cells, which
then shrink.
During the defrosting process, only
some of this water is reabsorbed by the
cells; the rest collects around the food.
If food is frozen quickly, the cells have
less time to lose moisture, so they
shrink less. As there is not so much
moisture loss, it is easier for the food to
reabsorb it during the defrosting
process, and very little water collects
around the defrosted food.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing and storing food
Home freezing
– Do not season fresh foods or
blanched vegetables before
Only freeze fresh food which is in a
good condition.
freezing. Only season cooked food
lightly before freezing, but care
should be taken as the taste of some
spices alters when frozen.
Hints on home freezing
– The following types of food are
suitable for freezing:
– Do not place hot foods or drinks in
the freezer. This causes already
frozen food to thaw, and increases
the energy consumption
Fresh meat, poultry, game, fish,
vegetables, herbs, fresh fruit, dairy
products, pastry, leftovers, egg
yolks, egg whites and a range of
pre-cooked meals.
considerably. Allow hot foods and
drinks to cool down before placing
them in the freezer.
– The following types of food are not
suitable for freezing:
Packing
Grapes, lettuce, radishes, sour
cream, mayonnaise, eggs in their
shells, onions, whole raw apples and
pears.
^ Freeze food in portions.
Unsuitable packing material
- wrapping paper
- grease-proof paper
- cellophane
– To retain colour, taste and vitamin C,
vegetables should be blanched after
they have been trimmed and
washed.
- bin bags
- plastic carrier bags
To blanch: Bring a large saucepan of
water to the boil, immerse the
vegetables in the fast boiling water
for 2-3 minutes, depending on
variety. Remove, and plunge into
ice-cold water to cool quickly. Drain
and pack ready for freezing.
Suitable packing material
- plastic freezer film
- freezer bags
- aluminium foil
- freezer containers
^ Expel as much air as possible from
bags etc. before sealing them, to
prevent freezer-burn on food.
– Lean meat freezes better than fatty
meat, and can be stored for
considerably longer.
^ Close the packaging tightly with
- rubber bands
– To prevent chops, steaks, cutlets or
rolled meat from freezing together in
solid blocks when packed, separate
with a sheet of plastic freezer film.
- plastic clips
- string or bag ties
- freezer tape.
Freezer bags may also be sealed
using home heat sealing kits.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing and storing food
^ Make a note of the contents and the
Please note that when removing the
drawers, the lowest freezer drawer
must always remain in the freezer.
When placing food on the glass cold
plate make sure it does not obstruct
the ventilation gaps at the back.
This is important for problem-free
operation and normal energy
consumption.
date of freezing on the packaging.
Before placing food in the freezer
^ When freezing more than 2 kg of
fresh food, switch on the Super
freeze function some time before
placing the food in the freezer (see
"Super freeze").
This also helps to prevent food that is
already in the freezer from starting to
defrost.
– Freezing the maximum amount
(see data plate)
^ Remove the upper freezer drawers.
Placing food in the freezer
^ Place the food flat on the upper glass
cold plates so that it freezes through
to the core as quickly as possible.
The following maximum capacities
must be observed:
– freezer drawer = 25 kg
– glass cold plate = 35 kg
Once frozen:
^ Place the frozen food in the freezer
drawers and push them back into the
appliance.
Food to be frozen must on no
account touch food which is already
frozen to avoid partial thawing.
– Large items
^ Make sure that the packaging and
containers are dry to prevent them
sticking together when frozen.
If you wish to freeze large items such
as a turkey or game, the glass cold
plates between the drawers can be
removed.
– Freezing small amounts of food
^ Remove the upper freezer drawers
and carefully lift and slide out the
glass cold plates.
Place the food in the upper freezer
drawers.
^ Place the food flat in the bottom of
the drawers so that it freezes through
to the core as quickly as possible.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing and storing food
Freezer calendar
Poultry It is particularly important to
observe food hygiene rules when
defrosting poultry. Do not use the liquid
from defrosted poultry. Pour it away
and wash the container it was in, the
sink and your hands. Danger of
salmonella poisoning.
The freezer calendar on the freezer
drawer gives the length of time in
months which various foods can be
stored for effectively.
Where the storage time given on the
packaging differs, follow the advice on
the packaging.
Ensure that meat and fish (e.g mince,
chicken, fish fillets) do not come into
contact with other foods when thawing.
Collect the liquid and dispose of it
carefully.
Fruit should be defrosted at room
temperature in its packaging, or in a
covered bowl.
2-3 months:
Most vegetables can be cooked while
still frozen. Just put straight into boiling
water or hot fat. The cooking time is
slightly less than that of fresh
vegetables due to changes in the cell
structure.
Cakes, ice cream, stews
3-5 months:
Fish, mushrooms, bread
6-8 months:
Pork, veal, poultry
Never re-freeze partially or fully
defrosted food. Consume defrosted
food as soon as possible as it will
lose its nutritional value and spoil if
left for too long. Defrosted food may
only be re-frozen after it has been
cooked.
10-12 months:
Beef, fruit, vegetables
Defrosting
Frozen food can be defrosted in
different ways:
– in a microwave oven,
– in an oven using the "Fan" or
"Defrost" setting,
– at room temperature,
– in the refrigerator (the cold given off
by the frozen food helps to keep the
other food cold),
– in a steam oven.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezing and storing food
Ice cubes
Cool pack
The cool pack prevents the
temperature in the freezer rising too
quickly in the event of a power cut. This
can help to prolong the storage time.
^ Place the cool pack in the top drawer
of the freezer.
^ Fill the ice tray three quarters full with
water and place it on the bottom of
one of the freezer drawers.
The cool pack will be at its most
effective after it has been in the
freezer for approx. 24 hours.
^ Once frozen, use a blunt instrument,
for example a spoon handle, to
In the event of a power cut:
^ Place the frozen cool pack directly on
top of the frozen food in the front of
the top drawer.
remove the ice tray from the freezer.
^ Ice cubes can be removed easily
from the tray by twisting the tray
gently or by holding it under cold
running water for a short while.
When placing fresh food in the freezer,
use the cool pack to separate the fresh
food from the food which is already
frozen so that the frozen food does not
begin to thaw.
Cooling drinks
Do not store cans or bottles containing
carbonated drinks or liquids which
could freeze in the freezer section. The
cans or bottles could explode.
The cool pack can also be used in a
cool bag to keep food or drinks cool for
a short period of time.
When cooling non-carbonated drinks
quickly in the freezer section, make
sure bottles are not left in for more
than one hour, otherwise they could
burst.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Defrosting
Refrigerator section and
PerfectFresh zone
Freezer section
This appliance is equipped with a "Frost
free" system. The freezer section
defrosts automatically.
Condensate and frost can build up on
the back wall of the refrigerator section
and the PerfectFresh zone whilst in use.
You do not need to remove this, as it
will defrost and evaporate automatically
with the warmth generated by the
appliance.
The moisture generated in the
appliance collects on the condenser
and is automatically defrosted and
dissipated by the condenser from time
to time.
The condensate is drained away via a
channel and drain hole into an
evaporation system at the back of the
appliance.
This automatic defrosting system
enables the freezer section to remain
permanently ice-free, however, the food
stored in the freezer section will not
defrost.
Ensure that the condensate channel
and drain hole are kept clean and
are never blocked so that
condensate can flow away without
hindrance.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
A range of Miele branded cleaning
and conditioning products is
available to order from Miele or
Unlike stainless steel cleaning
agents, the conditioning agent does
not contain any abrasive substances
and will gently remove soiling. Each
time it is used, it forms a water and
dirt repellent protective coating.
Make sure that no water can
penetrate into the electronic unit or
into the light.
To avoid damaging the surface of
your appliance, do not use:
Do not let water get into the
condensate channel and drain hole
when cleaning.
– cleaning agents containing soda,
ammonia, acids or chlorides,
– cleaning agents containing
descaling agents,
Do not use steam cleaning
apparatus to clean the appliance.
Steam could reach electrical
components and cause a short
circuit.
– abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
– solvent-based cleaning agents,
– stainless steel cleaning agents,
– dishwasher cleaner,
The data plate located inside the
appliance must not be removed. It
contains information which is required
in the event of a service call.
– oven sprays,
– glass cleaning agents,
The stainless steel doors have a
special finish which is resistant to
soiling.
– hard, abrasive sponges and
brushes, e.g. pot scourers,
– melamine eraser blocks,
– sharp metal scrapers.
Do not treat the doors with stainless
steel conditioning agent as this will
cause noticeable smearing.
Before cleaning
However, do use Miele stainless
steel conditioning agent to treat the
other stainless steel surfaces of the
appliance (available from Miele or
www.miele-shop.com).
^ Switch the appliance off.
^ Disconnect it from the mains.
^ Take any food out of the appliance
and store it in a cool place.
^ Take out any removable parts, e.g.
shelves, for cleaning.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
^ The bottle shelf and condiment tray in
the door can be removed from their
stainless steel frames for cleaning.
To remove the stainless steel trim from
the lid of the butter and cheese
compartment (in the top of the door),
proceed as follows:
^ Take the butter and cheese
compartment out of the refrigerator
section.
^ Pull the dividing plate out with both
hands.
^ Take out any removable parts, e.g.
^ Open the lid of the compartment.
shelves, for cleaning.
The stainless steel trim is a tight fit
across the plastic lid and will require
sufficient force to detach it.
Cleaning the interior and
accessories
^ Clean the appliance at least once a
month.
Remove soiling immediately to
prevent it from drying on.
Use lukewarm water with a little
washing-up liquid.
The following are dishwasher safe:
^ Detach the stainless steel trim from
the edge of the lid (1.) at one side
and remove.
– the butter dish, egg trays and ice
cube tray (supplied as standard,
depending on model)
^ Press the white plastic stoppers out
– the bottle shelf and condiment tray in
the door (removed from their stainless
steel frames)
of notches (2.).
^ After cleaning, refit the stainless steel
trim onto the lid in the reverse order.
– the butter and cheese compartment
(with the stainless steel trim removed)
^ Remove the compartments and the
lid from the PerfectFresh zone (see
"Adjusting the interior fittings -
The stainless steel frames and the
stainless steel trim on the butter and
cheese compartment in the door are
not suitable for cleaning in a
dishwasher.
PerfectFresh zone compartments")
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Appliance doors, side panels
The temperature of the dishwasher
programme must not exceed 55 °C.
Contact with some foodstuffs, such
as carrots, tomatoes or ketchup can
cause plastic items to discolour.
However, this discolouration will not
affect the stability of plastic items.
Remove any soiling from the
appliance doors and side panels im-
mediately.
If this is not done, it might become
impossible to remove and could
cause the surface to alter or
discolour.
^ Clean the interior shelves, dividing
plate, compartment and
compartment lids by hand. These are
not suitable for cleaning in a
dishwasher.
All surfaces are susceptible to
scratching.
Contact with unsuitable cleaning
agents can alter or discolour the
surfaces.
^ Clean the condensate channel and
drain hole frequently, so that
condensate can drain away
^ The surfaces should be cleaned
using a solution of hot water and a
little washing-up liquid applied with a
soft sponge. They can also be
unhindered. Use a straw or similar to
clear the drain if necessary.
^ After cleaning, wipe the interior and
accessories with a damp cloth and
dry with a soft cloth.
cleaned with a damp microfibre cloth
(without using any cleaning agent).
Leave the doors open to air the
appliance for a short while.
^ After cleaning, wipe with a damp
cloth and dry with a soft cloth.
^ Miele stainless steel conditioning
agent can be used to remove any
soiling from stainless steel trim and
frames.
Stainless steel appliances
– Appliance doors
The appliance doors have a high
quality, special finish which is resistant
to soiling and is very easy to clean.
^ It is important to treat the stainless
steel frames and trim with Miele
stainless steel conditioning agent
each time they are cleaned. This will
protect the surface and help prevent
resoiling.
Do not use the following to
clean/condition the doors
– stainless steel cleaning agent:
this will damage the surface.
– Miele stainless steel conditioning
agent:
this will cause noticeable smearing.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
– Side panels
Metal grille at the back of the
appliance
^ Use Miele stainless steel conditioning
agent to remove any soiling from
stainless steel surfaces.
The compressor and metal grille at the
back of the appliance (heat exchanger)
must be dusted at least once a year. A
build-up of dust will increase the
^ Make sure you treat the side panels
with Miele stainless steel conditioning
agent each time you clean them.
This will give them a water and dirt
repellent protective coating and help
prevent re-soiling.
energy consumption of the appliance.
When cleaning make sure that the
cable, pipework and other
components do not get broken,
kinked or damaged in any way.
Ventilation gaps
^ The ventilation gaps should be
cleaned regularly with a brush or
vacuum cleaner. A build-up of dust
will increase the energy consumption
of the appliance.
After cleaning
^ Push the dividing plate in until it
clicks into place.
^ Replace all shelves and accessories
in the refrigerator section.
Door seals
^ Put the food back in the refrigerator.
Do not use any oils or grease on the
door seals as these will cause the
seals to deteriorate and become
porous over time.
^ Reconnect to the mains and switch
the appliance back on.
^ Switch on the Super freeze function
so that the freezer can cool down
quickly.
The door seals should be cleaned
regularly with clean water, and then
wiped dry with a soft cloth.
^ Once the freezer has reached the
required temperature, place the food
back in the freezer drawers and put
them back in the freezer.
^ Switch off the Super freeze function
as soon as the temperature in the
freezer is a constant -18 °C or colder.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Active charcoal filters
The active charcoal filters should be
changed approx. every 6 months.
To confirm the filters have been
changed
When the Change active charcoal filter
indicator lights up red, the active
charcoal filters need to be changed.
^ Touch the Change active charcoal
filter indicator for approx. 2 seconds.
The indicator light will go out, and the
counter will be reset.
To change the active charcoal
filters
To delay changing the active
charcoal filters
If you do not have new active charcoal
filters, you can order them from your
Miele dealer or from Miele.
You can switch off the Change active
charcoal filter indicator early, if you
would prefer not to have the red
indicator showing.
^ Pull the active charcoal filter holder
upwards to remove it from the shelf.
^ Touch the Change active charcoal
filter indicator for approx. 2 seconds.
The Change active charcoal filter
indicator will go out.
^ Take out the two filters and fit the new
filters into the holder with the
protruding edge facing downwards.
^ Place the holder in the middle of the
raised edge at the back of the shelf,
so that it clicks into position.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Active charcoal filters
If you have delayed changing the
active charcoal filters and the indicator
is not lit up, you will need to reset the
counter when you replace the active
charcoal filters via settings mode.
Useful tip:
When you are storing foods with a
strong smell (such as ripe cheeses),
– place the holder containing the
active charcoal filters on the shelf
where the food is going to be stored,
– change the active charcoal filters
early if required (remembering to
reset the counter),
^ Touch and leave your finger on the X
sensor.
– and place more active charcoal
filters (in holders) in the appliance.
Active charcoal filters and holders
can be obtained from your Miele
dealer or from Miele.
^ At the same time, briefly touch the
On/Off sensor (without letting go of
the X sensor).
^ Leave your finger on the X sensor for
another 5 seconds until c appears in
the display.
^ Touch the X sensor repeatedly until
^ appears in the display.
^ Touch the On/Off sensor.
^ Touch the X sensor repeatedly until
^ 2 appears in the display.
^ Touch the On/Off sensor for approx.
2 seconds to confirm.
The counter is now reset.
^ Touch the X sensor repeatedly until
c appears in the display.
^ Touch the On/Off sensor.
You have now left settings mode.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
. . . the temperature in the refrigerator
section or freezer section is too low.
Repairs to electrical appliances
should only be carried out by a
suitably qualified and competent
person in strict accordance with
current local and national safety
regulations. Repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
^ Select a warmer temperature.
^ Check that the doors have been
closed properly.
^ Has a large amount of fresh food
been put in at the same time for
freezing?
This makes the compressor run for
longer, causing the temperature to
fall automatically.
unauthorised work.
What to do if . . .
^ Super cool has not yet switched itself
off.
. . . the refrigerator section or freezer
section does not get cold.
^ Super freeze has not yet switched
itself off.
^ Check whether the relevant section is
switched on. The temperature display
must be lit up.
. . . the compressor is switching in
too frequently and for too long.
^ Check that the plug is correctly
inserted into the socket and switched
on.
^ Check whether the ventilation gaps
have been covered over or become
dusty.
^ Check that the fuse is not defective
and the mains fuse has not tripped. If
it has, there could be a fault with the
household electrical wiring, the
fridge/freezer or another electrical
appliance. Contact a qualified
electrician or Miele.
^ Check whether the metal grille (heat
exchanger) at the back of the
appliance has become too dusty.
. . . the door to the freezer section
will not open because it has been
opened and closed too many times in
succession.
This is not a fault. The suction caused
by opening and closing the door
several times in succession is
preventing it from opening. Wait a few
minutes and then try again. It should
now open without force.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
^ The doors have been opened too
. . . the alarm sounds and the alarm
frequently, or a large amount of fresh off sensor is flashing.
food has been put in at once for
One of the sections is too warm,
freezing.
because
^ Check that the doors have been
^ the door has been opened too
frequently, or large amounts of fresh
food have been placed in the
appliance at once.
closed properly.
. . . the compressor runs
continuously.
^ the ventilation gaps are blocked.
To save energy, the compressor runs at
a lower speed, but for longer, when
less cooling is required. In this case,
the motor runs for longer.
Once the problem has been resolved
and the correct temperature has been
reached, the alarm indicator will go out
and the alarm will stop.
. . . the frozen food is thawing
because the freezer is too warm.
. . . bars light up in the temperature
displays.
^ Is the room temperature lower than
the ambient temperature for which
the appliance is designed?
Check the temperature display about 6
hours after switching on the appliance.
Only temperatures within the range the
appliance can display will be shown.
If so, increase the temperature of the
room.
. . . "_F" appears in the temperature
display.
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the freezer to
become too warm.
There is a fault. Call Miele Service.
. . . the Change active charcoal filter
indicator is red.
. . . food has frozen together.
Use a blunt instrument, e.g. a spoon
handle or plastic scraper, to prise it
apart carefully.
^ Replace the active charcoal filters.
You can order replacement filters via
your Miele dealer or Miele.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
. . . "nA" appears in the temperature
The LED lighting may only be repaired
or replaced by a service technician.
There are live electrical components
under the cover. Danger of injury and
damage to the appliance.
display.
The temperature has risen too high at
some point during the last couple of
days because of a power cut.
Do not remove the cover. If the
cover is damaged or needs to be
removed due to damage, exercise
caution. There are lasers in the
lighting (laser beam class 1M) which
you should avoid looking at directly.
Do not use optical instruments
(magnifying glass or similar) to look
at the lighting either.
^ Touch the alarm off sensor whilst "nA"
is lit up in the display.
The temperature display will show the
warmest temperature recorded in the
freezer section during the power cut.
Depending on the temperature
displayed, you should check the
condition of food in the freezer section.
If it has defrosted or started to defrost,
check that it is still safe to use and if so
use it as soon as possible. Defrosted
food may only be re-frozen after it has
been cooked.
. . . the floor of the refrigerator
section is wet.
The condensate drain hole is blocked.
^ Clean the condensate channel and
The warmest temperature will show in
the display for about 1 minute. The
display will then revert to showing the
current temperature in the freezer
section.
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
. . . you cannot switch the appliance
off.
To prevent unnecessary loss of
temperature it is advisable not to
open the doors while waiting for the
appliance to be serviced.
The safety lock has been activated.
. . . the interior lighting in the
refrigerator is not working.
^ Was the refrigerator door left open for
too long? The lighting switches itself
off automatically after approx. 15
minutes if the door is left open.
If this is not the case, then the interior
lighting is defective.
^ Call Miele Service.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Noises
Normal noises
What causes them
Brrrrr...
Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....
Click....
A gurgling noise can be heard when coolant is circulating
through the pipes.
Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....
Creak ...
On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creaking sounds can be heard when material inside the
appliance expands.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectify
What causes them, and what can you do about
them
Rattling, vibrating
The appliance is uneven: Realign the appliance using a spirit
level, by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture: Move it away.
Drawers, baskets or shelves are unstable or sticking: Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other? Separate them.
The transport cable clips are hanging loose at the back of
the appliance: Remove the clips.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales / Guarantee
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– your Miele Dealer
or
– Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
purchase. However, you must activate
your cover by calling 0845 365 6640 or
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Electrical connection U.K.
If the connection cable has to be
replaced, this must be done by a
suitably qualified and competent
person.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
Do not plug other appliances in behind
this appliance
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. It must not be located
behind the appliance. For extra safety it
is advisable to protect the appliance
with a suitable residual current device
(RCD).
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
WARNING
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
THIS APPLIANCE MUST BE
EARTHED
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
– Do not plug in other appliances
Do not place any appliance which
gives off heat, such as a toaster,
mini-oven or double burner hob, on
top of this appliance There is the
danger of these catching fire.
behind this appliance.
Important. In environments with
high humidity condensation can
build up on the exterior of the
appliance. This can cause corrosion
of the appliance walls. For
prevention, it is advisable to install
the appliance with sufficient
ventilation in a dry and /or
This fridge freezer must not be
installed directly next to another
refrigerator or freezer.
air-conditioned room.
It does not have side-wall heating,
so installation next to another
refrigerator or freezer could cause a
build-up of condensation between
them.
Make sure that the appliance door is
closing and sealing properly, the
ventilation gaps are not covered and
the appliance is installed in
accordance with these installation
instructions.
Further information is available from
your dealer.
Climate range
Location
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate.
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Climate range
Ambient room
temperature
SN
N
+10 °C to +32 °C
+16 °C to +32 °C
+16 °C to +38 °C
+16 °C to +43 °C
ST
T
When installing the appliance please
be aware:
Operating in a room which is too cold
will result in the cooling system
switching off for too long, causing the
internal temperature in the appliance to
rise with the risk of food deteriorating
and going off.
– The socket must be easily accessible
in an emergency, not concealed
behind the appliance.
– The plug and cable must not touch
the rear of the appliance as they
could be damaged by vibrations
from the appliance.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Ventilation
Installation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the ventilation gaps must not be
Two people are required to install
the appliance. Only move the
appliance when it is empty.
covered or blocked in any way. They
should be dusted on a regular basis.
^ Remove the cable clip from the back
of the appliance. This could cause
vibration noises.
Appliances with wall spacers
supplied
^ Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
The wall spacers supplied with
some appliances must be used in
order to achieve declared energy
consumption values. Appliance
depth is increased by approx. 35
mm with the wall spacers fitted. If
the wall spacers are not used, this
does not influence the functionality
of the appliance. Energy
^ Carefully push the appliance into
position.
^ Position the appliance with the wall
spacers (if used) or the back close to
the wall.
Aligning the appliance
consumption is only minimally
increased if there is little distance
between the appliance and the wall.
^ To align the appliance, adjust the
front feet using the spanner supplied.
^ Fit the wall spacers onto the back of
the appliance on the top left and
right.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Levelling the appliance door
^ Ensure that you unscrew adjusting
foot a until it sits on the floor. Then
unscrew the foot by a further 90°.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Appliance dimensions
A
B
C
KFN 14927 SD
2010 mm
2010 mm
600 mm
600 mm
630 mm*
630 mm*
KFN 14927 SD ed/cs
KFN 14927 SD ed/cs-1
KFN 14927 SD ed/cs-3
* Dimensions without wall spacers fitted. Appliance depth is increased by approx.
35 mm with the supplied wall spacers fitted.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
Removing the door handles
To change the door hinging you will
need the following tools:
Two people are needed for
changing the door hinging.
^ Pull door handle a towards you. Side
section b slides back.
^ Pull side section b firmly back out of
the guides on the mounting plate.
^ Undo the 4 screws (TX 15) in the
mounting plate, and remove the
handle.
^ Remove the cover caps from the
opposite side, and fit them into the
empty holes.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Before beginning, make sure that
the door shelves are empty.
Removing the soft-close mechanism
for the upper door
^ Open the upper door.
^ Slide panel a towards the appliance,
and leave it hanging between the
door and the appliance.
^ Fit restraining clip b (supplied with
the appliance) onto soft-close
mechanism c.
The restraining clip stops the hinge
from snapping shut. Do not remove the
clip until told to do so.
^ Remove panel a from the soft-close
mechanism by inserting a flat-bladed
screwdriver into the gap from above
and easing it off bit by bit.
Take care not to damage the door
seal.
If the door seal is damaged, the
door will not close properly and
cooling will be impaired.
^ Carefully prise open cover d from
above and below using a flat-bladed
screwdriver.
^ Push hinge pin e up and out from
underneath using a flat-bladed
screwdriver.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Remove cover d.
Removing the upper door
The soft-close mechanism is now no
longer fixed to the appliance.
^ Remove panel a.
^ Gently loosen cover h by carefully
inserting a flat-bladed screwdriver
into the gap.
^ Slide soft-close mechanism bracket
f as far as it will go towards the
handle side of the door, and undo
screws g on the soft-close
mechanism.
^ Remove cover h together with
retainer plate i.
^ Then separate retainer plate i from
cover h, by pushing it slightly to the
left and then pulling the cover
forwards and off.
^ Using a flat-bladed screwdriver, slide
the soft-close door mechanism
towards the handle side of the door,
and lever it out at the side.
^ Rotate retainer plate i by 180°.
^ Then fit cover h from the front over
retainer plate i, and push it over to
the right. The writing must be visible.
^ Then place it to one side.
^ Unscrew hinge part j, rotate by
180° and fit to the opposite side. If
necessary drill pilot holes for the
screws.
^ Remove cover k by sliding it
forwards from the back and then
lifting it off.
^ Remove cover l by pulling it
upwards.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
Take care not to damage the door
seal.
If the door seal is damaged, the
door will not close properly and
cooling will be impaired.
^ Close the upper door.
^ Undo screws m in upper hinge plate
n and pull it upwards and off.
^ Carefully lift the upper door off and
place it to one side.
^ Make sure that you leave the hinge
pin in the hinge plate in the middle of
the appliance, as otherwise the lower
door will be unsecured.
^ Then fit cover h together with
retainer plate i on the opposite side.
^ Slide panel a towards the appliance,
and leave it hanging between the
door and the appliance.
^ Refit cover l on the opposite side.
Removing the lower soft-close door
mechanism
^ Fit restraining clip b (supplied with
the appliance) onto soft-close
mechanism c.
^ Open the lower door.
The restraining clip stops the hinge
from snapping shut. Do not remove the
clip until told to do so.
^ Carefully remove cover d from the
side using a flat-bladed screwdriver.
^ With the help of another person, tip
the appliance back slightly.
^ Remove panel a from the soft-close
mechanism by inserting a flat-bladed
screwdriver into the gap from above
and easing it off bit by bit.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Removing the lower door
^ Close the lower appliance door.
^ Push hinge pin e up and out from
underneath.
The soft-close mechanism is now no
longer fixed to the appliance.
^ Pull the middle hinge pin i upwards
to remove it.
^ Remove panel a.
^ Carefully lift the lower door off and
place it to one side.
^ Pull cover j off.
^ Unscrew hinge plate k, rotate it by
180° and fit it on the opposite side.
^ Pull off plastic cap h, rotate it by
180° and fit it back on to middle
hinge plate k.
^ Slide soft-close mechanism bracket
f as far as it will go towards the
handle side of the door, and undo
screws g on the soft-close
mechanism.
^ Refit cover j on the opposite side.
^ Using a flat-bladed screwdriver, slide
the soft-close door mechanism
towards the handle side of the door,
and lever it out at the side.
^ Then place it to one side.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Unscrew part h from hinge plate f,
rotate it by 180° and refit into the hole
on the opposite side of the hinge
plate.
^ Refit cover cap d in the other hole.
^ Remove cover g and fit it into the
holes on the opposite side.
^ Screw hinge plate f into position on
the opposite side using the two outer
long slots only. To make it possible to
align the door later, do not replace
the centre screw at this stage.
^ Important. Screw the adjustable foot
c into hinge pin a as far as it will go.
^ Refit hinge pin a together with disc
b and adjustable foot c. Important.
The notch at the bottom of the hinge
pin should face towards the back.
^ Remove cap l from the bearing
bush in the door and refit on the
opposite side.
^ Place the lower door onto hinge pin
Refitting the lower door
a.
^ Close the lower door.
^ Pull hinge pin a together with disc b
and adjustable foot c upwards and
off.
^ Remove cover cap d.
^ Undo screws e and take hinge plate
f off.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Insert the soft-close mechanism back
into the door, starting at the right
hand side.
^ Fit hinge pin i into middle hinge
plate k in the lower door.
Replacing the lower soft-close door
mechanism
^ Using a flat-headed screwdriver,
slide the soft-close mechanism back
into the door as far as it will go
towards the appliance so that it clicks
into position.
^ Remove cover a from panel b,
rotate it by 180° and refit it on the
other side.
The screw holes on the left and right
must line up perfectly.
^ First screw the soft-close mechanism
onto the appliance side, then onto
the handle side c, pushing it firmly
towards the appliance.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Refitting the upper door
^ Then fit the upper door on middle
hinge pin i.
^ Close the upper door.
^ Attach panel b to soft-close
mechanism bracket d.
^ Align bracket d to the hinge plate,
and insert pin e from above so that
the right angle fits into the recess.
^ Click cover f back into place.
^ Fit hinge plate n onto the opposite
side and secure it with screws m.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.
Make sure that cover f fits properly so
that the door can be closed without
hindrance and the pin is protected.
^ Remove retaining clip g.
^ Refit cover k on the opposite side.
^ Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.
^ Replace panel b onto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^ Close the lower door.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Replacing the upper soft-close door
mechanism
^ Slide the soft-close mechanism back
into the door as far as it will go
towards the appliance using a
flat-headed screwdriver.
^ Remove cover a from panel b,
rotate it by 180° and refit it on the
other side.
The screw holes on the left and right
must line up perfectly.
^ Insert the soft-close mechanism back
into the door, starting at the right
hand side.
^ First screw the soft-close mechanism
onto the appliance side, then onto
the handle side c, pushing it firmly
towards the appliance.
^ Attach panel b to soft-close
mechanism bracket d.
^ Push cover e on from the side so
that the openings for the pin f are
vertically aligned.
^ Align bracket d to the hinge plate,
and insert pin f from above so that
the right angle fits into the recess.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
^ Clip cover e into position.
Make sure that cover e fits properly so
that the door can be closed without
hindrance and the pin is protected.
^ Remove retaining clip g.
^ Replace panel b onto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^ Close the upper door.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the door hinging
Refitting the handles
It is important to check that the side
section of the handle d does not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
Please make sure you follow the
instructions below carefully when
you refit the handles. The door seal
will be damaged if the handle is
fitted incorrectly.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^ Realign mounting plate c with grub
screws a until the mounting plate
and the side section of the handle d
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
^ Loosely attach the handle to the
opposite side of the door with the two
front screws b.
Mounting plate c must be positioned
on the side of the door so that when the
door is closed it is flush with the side of
the appliance.
If this is not the case,
^ tighten both grub screws a with a
suitable allen key until mounting plate
c lines up correctly.
^ Then tighten all 4 screws b.
^ Slide the side section of the handle
d into the guides on the mounting
plate until it clicks into place.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Aligning the appliance doors
The appliance doors can be aligned
with the housing after they have been
fitted.
To align the upper door use the long
outer slots in the middle hinge plate:
In the following illustration the door is
not shown in the closed position to
make it easier to see what you have
to do.
To align the lower door use the long
outer slots in the lower hinge plate:
^ Slightly loosen both screws c.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws c.
^ Remove centre screw a from the
hinge plate.
^ Slightly loosen both outer screws b.
^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws b again. Screw
a does not need to be used again.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top box a.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm2 to ensure that air can circulate
without hindrance. Otherwise the
compressor has to work harder,
resulting in an increase in electricity
consumption.
The ventilation gaps must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
* The appliance depth is increased
by approx. 35 mm for appliances
with wall spacers fitted.
When built into a kitchen run (max.
housing unit depth 580 mm) the
appliance can be installed directly next
to the furniture housing unit. The
appliance door will protrude in front of
furniture fronts at the sides by 34 mm*
and by 55 mm* in the middle of the
doors. This enables the doors to be
opened without hindrance.
aTop box
bAppliance
cHousing unit
dWall
When installed next to a wall d a
distance of approx. 55 mm must be
maintained on the hinge side between
the wall d and the appliance b, so
that the doors and the handles have
sufficient space for opening.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / 0513
M.-Nr. 09 436 290 / 00
KFN 14927 SD, KFN 14927 SD ed/cs (-1/-3)
Download from Www.Somanuals.com. All Manuals Search And Download.
|