Installation Instructions
.ꢀꢁꢂꢃꢄꢀ9Lꢅꢀ.ꢀꢁꢂꢁꢄꢀ9LꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀHQꢀꢁꢀ&$
.ꢀꢁꢆꢃꢄꢀ9Lꢅꢀ.ꢀꢁꢆꢁꢄꢀ9Lꢀ
ꢀ
ꢀ
,QVWDOODWLRQꢂꢀUHSDLUꢀDQGꢀPDLQWHQDQFHꢀZRUNꢀVKRXOGꢀEHꢀSHUIRUPHGꢀE\ꢀ
Dꢀ0LHOHꢀDXWKRUL]HGꢀVHUYLFHꢀWHFKQLFLDQꢀLQꢀDFFRUGDQFHꢀZLWKꢀQDWLRQDOꢀ
DQGꢀORFDOꢀVDIHW\ꢀUHJXODWLRQVꢀDQGꢀWKHꢀSURYLGHGꢀLQVWDOODWLRQꢀLQVWUXFWLRQVꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation site
Have the appliance installed by a
qualified technician, according to
the enclosed installation
instructions.
The appliance should be installed in a
dry, well ventilated room.
Do not install the appliance:
- outdoors,
- in an environment with dripping
water,
WARNING
This appliance is top-heavy and
must be secured to prevent it from
tipping forward.
- in rooms which are at risk of frost.
The installation location should not be
exposed to direct sunlight, nor near a
heat source, such as an oven,
radiator, etc.
Keep the door closed until the
appliance is completely installed
and secured as per the installation
instructions.
The ambient temperature should not
drop below 55°F (13°C) or rise above
110°F (43°C), otherwise malfunctions
may occur.
Empty weight of your machine:
K 18x3 Vi . . . . . . . . . . 419 lbs (189 kg)
K 19x3 Vi . . . . . . . . . . 452 lbs (205 kg)
If installation next to a heat source is
unavoidable observe the following
minimum distances from the heat
source:
Climate Range
The appliance is designed for use
within certain climate ranges (ambient
temperatures) and should not be used
outside this range. The climate range of
this appliance is stated on the data
plate inside the appliance.
– 1 1/4" (3 cm) from an electric cooktop
or electric oven.
– 12" (30 cm) from a gas or oil
cooktop, range or oven.
The following should also be taken into
consideration:
Climate
range
Ambient room temperature
– The electrical outlet must be easily
accessible in case of an
SN
N
+50°F (10 °C) to +90°F (32 °C)
+60°F (16 °C) to +90°F (32 °C)
+60°F (16 °C) to +100°F (38 °C)
+60°F (16 °C) to 110°F (43 °C)
ST
T
emergency,not concealed behind
the appliance.
– The plug and cord must not touch
the rear of the appliance as they
could be damaged by vibrations
from the appliance.
Operating in a room which is too cold
will cause the compressor to switch off
for too long, causing the internal
temperature in the appliance to rise
with the risk of food deteriorating and
going off.
– Do not plug in other devices behind
this appliance.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Important! When there is high
humidity a build-up of condensation
on the outer surfaces of the
appliance can occur.This can cause
the surfaces to corrode.To prevent
this, it is advisable to install the
appliance in a dry and/or an
air-conditioned room with sufficient
ventilation.Please ensure that doors
close and seal properly after
installation and that the appliance is
installed in accordance with these
installation instructions and and with
the required ventilation openings.
– If the room is too cold, it will cause
the cooling system in the appliance
to remain off for too long.This can
cause the temperature in the
appliance to rise, resulting in
damage.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Base
Ventilation
A fully loaded appliance is very heavy.
The load-bearing capacity of your floor
must meet the following requirements:
The air intake and outlet must not be
blocked or covered in any way. They
also need to be dusted/cleaned on a
regular basis.
K 18x3 Vi . . . . . . . . . . 996 lbs (452 kg)
K 19x3 Vi . . . . . . . . . 1,191 lbs (540 kg)
Installation niche
To ensure that the appliance is installed
securely and functions properly, the
base must be flat, level and made of a
hard, rigid material.
To ensure safe, trouble-free installation
and the best possible cosmetic result,
check to be sure that the installation
space complies with the installation
dimensions. See "Niche dimensions".
If in doubt, contact Miele.
The side walls of the installation cavity
must be plumb.
Furniture/fixtures
The minimum thickness of the side
walls and the top wall must be 5/8"
(16 mm).
The new appliance will be mounted
securely to adjacent and overhead
furniture/fixtures.
For this reason it is essential that all
attachable furniture/fixtures are
connected securely to the base or the
wall by suitable means.
The minimum thickness of the toe-kick
panel must be ½" (13 mm). A thickness
of 3/4" (19 mm) is recommended.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Stainless steel panels
Side-by-side
Stainless steel door panels and toe-kick This appliance can be installed
covers are available from Miele.
"side-by-side" with another
fridge/freezer using a "Merging Kit".
Custom door panels
The "Merging Kit" is available from
Miele.
This appliance is compatible with all
styles and designs of kitchen cabinetry.
Contact Miele or your dealer for
specific information about which
combinations will work with your
appliance.
The total weight of the decorative
panel(s) must not exceed the following:
K 18x3 Vi. . . . . . . . . . . . 110 lbs (50 kg)
K 19x3 Vi. . . . . . . . . . . . . 81 lbs (37 kg)
For instructions on how to attach the
appliances and install the heating
mat, please refer to the instructions
included with the "Merging Kit",
available from Miele.
Installation options
There are many different installation
options. These are limited only by the
design of the kitchen.
Installation without a partition using
the "Merging Kit"
The door hinge cannot be
exchanged.
Single column
The appliance can be installed at any
preferred location in the kitchen.
However, be sure the door will open
and close properly in the chosen
location.
If the appliances are installed directly
next to each other (without a partition),
they need to be attached together
using the "Merging Kit".
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation with partition using the
"Merging Kit"
Side panels
If one side of the appliance is visible, a
side panel must be used.
The minimum thickness of the partition
is 5/8" (16 mm).
The side panel must be firmly secured
to the wall, the floor and the overhead
furniture/fixtures before the appliance is
placed in the cavity.
The dimensions of the side panel are
taken from the opposite wall of the
installation space. During installation,
ensure that the cavity is square and the
measurements are correct.
If there is a partition with a thickness
from 5/8" (16 mm) to 6 5/16" (160 mm)
between the adjacent appliances, then
each appliance should be individually
installed within its own niche using the
mounting accessories included.
The "Merging Kit" will also be needed.
The "Merging Kit" is available from
Miele.
Installation with partition without
using the "Merging Kit"
If there is a partition with a thickness of
more than 6 5/16" (160 mm) between
the adjacent appliances, then each
appliance should be individually
installed within its own niche using the
mounting accessories included (the
"Merging Kit" is not necessary).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Adjusting the door opening
angle (optional accessory)
Front panel gap kit (optional
accessory)
Depending on the installation site, it
may be necessary to adjust the door
opening angle to 90°.
^ Open the door.
Two adjacent furniture doors can be
attached instead of one large door.
^ Insert the banking pin through the
To connect these furniture doors on the
rear, a metal strip can be purchased as
an optional accessory. Contact Miele.
holes and drive in with a hammer.
The door opening angle is now limited
to 90°.
When attaching the metal strip to the
furniture doors, observe the maximum
length of the screws and the position of
the drill holes.
Always screw into the best possible
load-bearing material of the custom
doors.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Door dimensions (open min. 90°)
*The dimensions of the door fronts and
handles will vary according to each
individual kitchen.
3/8" (10 mm)
A
B
C
K 18X3 Vi 32 5/8" (829 mm)
Door front max. 1 1/2" (38 mm) Door handle*
K 19X3 Vi 38 11/16" (982 mm) Door front max. 1 1/2" (38 mm) Door handle*
Door dimensions (open min. 115°C)
*The dimensions of the door fronts and
handles will vary according to each
individual kitchen.
A
B
C
D
K 18X3 Vi 32 5/8" (829 mm) Door front max.
Door handle* 14 5/16"
(363 mm)
1 1/2" (38 mm)
K 19X3 Vi 38 11/16" (982 mm) Door front max.
Door handle* 16 7/8"
(428 mm)
1 1/2" (38 mm)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Niche dimensions
Niche width (A)
K 18X3 Vi
K 19X3 Vi
30" (762 mm)
36" (915 mm)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Power supply
1. Power supply
A
K 18X3 Vi
K 19X3 Vi
15" (381 mm)
18" (458 mm)
,Power bars or extension cords
are not safe (risk of fire). Do not use
them to connect the appliance to
the power supply.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Door front dimensions
A
B
1
K 18X3 Vi 79 /8"
29 3/4"
7
(2029 mm) (756 mm)
1
K 19X3 Vi 79 /8"
35 3/4"
7
(2029 mm) (908 mm)
4" - 5 3/16" (102 - 132 mm)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Before you begin
– Multi-grip pliers
– Level
Read these instructions completely
and carefully.
– Tape measure
– Square
Have the appliance installed by a
qualified technician, according to
the enclosed installation
instructions.
When fastening the cabinet to the wall
behind it (see "Installing the appliance")
use:
– suitable plugs/screws depending on
the type of wall.
To reduce the risk of injury or
damage to the product, two people
should be used for installation.
– several mounting brackets, if required.
Other
These installation instructions are
intended for use by qualified installers.
In addition to these instructions, the
appliance must be installed in
accordance with all local codes. In the
absence of a local code, the following
should be used:
– Stepladder
– Dolly, hand truck
– Wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] as an alternative
tilt protection, length depends on the
width of the installation cavity)
– In the USA, the National Electric
Code, ANSI/NFPA 70 - latest
edition/State and Municipal codes
and/or local codes.
– Wood screws in different sizes
Optional accessories
– In Canada, the Canadian Electric
code C22.1 - latest edition/Provincial
and Municipal codes and/or local
codes.
– "Merging Kit" for side-by-side installation
– Front panel gap kit
– RemoteVision module for wireless
monitoring
Tools needed for installation
– Cordless screwdriver
– Torx screwdriver
– Hammer drill
– Wood drills in different sizes
– Hammer
– Rachet 5/16" (8 mm)
– Adhesive tape
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Aligning the housing unit
Check the installation niche
To ensure a safe, trouble-free
installation and the best possible
cosmetic result, check to be sure
that the installation space complies
with the installation requirements.
^ Check the base (see "Installation").
^ Check the dimensions of the cavity.
^ Check that the cavity is square.
^ Check the location of the power
outlet.
^ Check that all furniture parts in the
vicinity of the appliance are securely
connected to the wall.
The housing unit must be carefully
aligned using a spirit level before
installing the appliance. The unit
corners must be at right angles, as
otherwise the furniture door will not
align correctly with the 4 corners of the
appliance.
^ Check that the adjacent
furniture/fixtures do not collide with
the open door.
Before installation
,Caution - the appliance is very
heavy. Use caution when unpacking
and opening the door, danger of
tipping.
– The side panels of the housing must
be even.
– The housing unit panels must be at
least 5/8" (16 mm) thick.
^ To protect the base from damage
during installation, attach a hard
board, linoleum, etc., to the floor in
front of the intended installation
location.
– The plinth facing must be at least
1/2" (13 mm) thick, preferably 3/4"
19 mm).
^ Remove any cable clips from the
back of the appliance.
^ Take the supplied accessories out of
the protective packaging.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
,Caution! The appliance is no
longer secured and may be
unstable.
^ From the rear of the appliance
carefully lift it from the pallet.
Once the appliance is on the ground it
can be wheeled around.
^ Do not remove the installation
supports from the appliance door.
They will be used later in the
installation niche.
RemoteVision module
installation
(optional accessory)
There are transportation safety
devices inside the appliance to
protect the shelves and storage
compartments until installation is
complete. Do not remove them, or
parts may be damaged.
Always disconnect the appliance
from the power supply when
performing installation, maintenance
or service work.
Install the RemoteVision module
before placing the appliance in its
installation niche.
^ Check the appliance for damage in
transit.
Once connected the RemoteVision
module will increase the energy
consumption of the appliance.
Do not install the appliance if it is
visibly damaged. If in doubt, contact
your dealer.
^ Loosen the bracket that holds the
The slot for the RemoteVision module is
located in the lower area of the back of
your appliance.
appliance to the pallet.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Unscrew the screws a on the cover
b and pull off the sticker c.
^ Pull the antenna d straight out.
^ Remove the cover b.
^ Guide the cover b over the antenna
d and screw on the cover.
^ Push the module into the slot until it
locks into place.
^ Angle the antenna d so that it faces
to the right or left.
^ Connect the appliance to the power
supply and turn it on. After several
seconds the indicator light e will
come on.
^ If necessary, disconnect the power
supply and continue installing the
appliance.
The indicator light will display different
colors one after the other; any control
light at the end indicates that the
module was correctly installed.
Preparing the installation
niche
,Keep the appliance door closed
until it is securely fastened in the
niche. Tipping hazard.
If the indicator light does not come on,
installation of the module was
unsuccessful. In that case, repeat the
process. If that does not correct the
problem, contact Miele.
Because of the size and weight of
the appliance, it is essential to
ensure that the appliance cannot tip
over once it has been mounted in
the niche.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Mounting Accessories
Two anti-tip brackets are
recommended for each appliance. For
side-by-side installations 4 brackets are
recommended.
The mounting accessories needed for
installing the appliance into the niche
are included in the packaging. Several
plastic bags are included which are
numbered alphabetically.
^ Position the anti-tip brackets on the
left and right in the installation niche
so that there is no more than 3/8"
(10 mm) of space between the
brackets and the side walls.
The bag needed for each step will be
marked with its respective letter.
Anti-tip brackets
The anti-tip brackets a keep the
appliance safely secured in the
installation niche b and prevent it from
tipping.
^ Mark the drill holes in the anti-tip
brackets on the back wall and on the
ceiling of the installation niche.
^ Set the brackets aside - they will be
needed again later.
Screws are supplied with the
appliance for various
applications/materials.
If the anti-tip brackets cannot be
attached securely with the screws
supplied, an alternative anti-tip
device can be used.
Assure that there are no electrical
wires in the area which the screws
could penetrate - risk of injury and
damage.
,Risk of tipping
The installation niche must be
securely attached to the wall behind
it. This is the only way the
appliance, which is later secured in
the niche, can be prevented from
tipping!
^ Now attach the installation niche to
the wall.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Securing an alternative anti-tip
device
– The beam must cover the appliance
by at least 2" (50.8 mm).
If the anti-tip brackets cannot be
attached securely, an alternative
anti-tip device can be used.
^ Mark the installation height (lower
edge of the beam) on the rear wall of
the niche.
Ensure that there is no "give" between
the appliance and the anti-tip device.
^ Select screws according to the
thickness of the wooden beam.
Example: 3 ½" (89 mm) screw for 2x4
beam.
If possible, always screw the
wooden beam to existing studs.
^ Determine the number of screws
based on the cavity width, to ensure
that the beam will be attached
securely.
^ Locate wall studs near the rear wall
of the cavity and mark drill holes in
the beam.
^ Pre-drill the wooden beam.
^ Attach the wooden beam to the rear
wall of the niche.
– Cut a wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] to the required
length).
– The length is equal to the width of
the installation niche.
– If the installation niche is deeper than
the appliance, select a beam with a
larger cross section, or attach two
beams.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Sliding the appliance into the
installation space
^ Plug the appliance into the power
outlet a.
The plug of the appliance should be
easily accessible after installation.
If the plug is not accessible after the
appliance has been installed,
disconnection from the power
supply should be completed via the
circuit breaker.
If a side-by-side installation is
desired, connect the two appliances
together. See the Installation Manual
included with the "Merging Kit".
In the case of side-by-side
installations, a separate outlet must
be used for each appliance.
^ To prevent the power cord from
becoming caught:
Tie a piece of string to the middle of
the power cord and feed it forward
under the appliance. When sliding
the appliance in, pull the cable
forward b.
^ Unscrew the plinth.
^ Carefully slide the appliance into the
space.
If resistance is felt when attempting to
slide the appliance into the installation
niche - for example, because the floor
is uneven,
^ Turn the rear adjustable wheels
slightly outward (see "Aligning the
appliance"), then push the appliance
in.
Be careful not to damage the power
cord attached to the floor.
^ Remove the edge protectors.
^ To protect the corners of the
installation space, attach edge
protectors where needed (not
included).
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Aligning the appliance
Important!
^ Align the appliance with the custom
When unscrewing the
height-adjustable feet, proceed
gradually, alternating between left
and right.
front.
^ Unscrew the height-adjustable feet
until the mark on the base has
reached the indicated guide
dimension 1 1/4" (32 mm). The guide
dimension of 1 1/4" (32 mm) is
related to a niche height of 84"
(2134 mm).
The installation aids c on the
appliance door have been designed for
custom door thicknesses of 3/4"
(19 mm) and 1 1/2" (38 mm).
The height-adjustable feet at the front
and rear can all be adjusted from the
front:
– Front feet:
Adjust with a rachet 5/16" (8 mm) d
– Rear feet:
^ Align the custom door with a level.
Adjust with a (cordless) screwdriver
and/or a rachet 5/16" (8 mm) for fine
adjustment e
Note:
– When unscrewing the
height-adjustable feet, proceed
gradually, alternating between left
and right.
^ Use a level to align the installation
aids c on the door.
– If using a wooden beam as an
alternative anti-tip device, rotate the
appliance all the way toward the
wooden beam.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Attaching the appliance to the
installation niche
^ Secure the attachment plate side lugs.
If there is a fairly large gap above the
appliance, cut a wooden beam to fit
exactly and place it in the gap.
^ Screw the attachment plate lugs f to
the overhead furniture/fixtures.
^ If necessary, shorten the filler strip h
to the required height.
If there is no way to attach the top of
the appliance, it can be attached to the
sides of the installation niche.
^ Place the 2 strips on top of each
other i.
^ Insert the filler strip until you hear it
click into place j.
^ Pull out the plate side lugs g.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
For a side-by-side combination the filler ^ Open the appliance door.
strips from both appliances are put
together to form one long filler strip:
^ Take the peg from the "side-by-side
merging kit" and insert it halfway into
the filler strip rail on the left-side
appliance.
^ Place the second filler strip on the
^ Screw the attachment plate lugs k to
the adjacent furniture/fixtures.
peg and press both filler strips
together.
With side-by-side combinations, only
the external side of the appliances can
be secured to the niche.
^ Insert both filler strips into the
installation space above the
appliance, until they click into place.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Preparing the custom door
^ Open the appliance door.
^ Unscrew the installation supports l
from the appliance door.
^ Measure the distance X between the
bracket from the door and the
overhead furniture/fixtures.
^ Loosen the remaining screws from
the strips m on each side of the door,
then remove.
^ Loosen the two nuts.
Set aside the nuts - you will need
them again later.
^ Set aside the screws and side strips
m - you will need them again later.
^ With the inside facing up, lay the
custom door on a stable surface (to
avoid scratch marks, place some
plastic or a cloth on the surface).
^ Remove the light switch cover (see
arrow).
^ Close the appliance door.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Mark the distance X on the back-side
Please note: When attaching the
mounting frame onto two adjacent
doors (see "Front panel gap kit")
screw into the thicker outer frames
of the doors only.
of the custom door.
^ Also calculate and mark the center of
the custom door Y.
^ Remove the mounting frame from the
appliance door and position it
according to the markings on the
custom door.
The bracket includes a variety of holes
for the various design options of
custom doors.
^ Pre-drill the holes.
When performing work on the custom
door, always observe the following:
^ Tightly screw on the bracket using
the pre-drilled holes:
– Always select the best load-bearing
surface of the custom door as the
location for screws.
Attach the bracket to each
attachment point with at least one
screw.
– Always select a screw length that is
shorter than the thickness of the door
front.
^ Attach the bracket at the top with at
^ Secure the door handle to the front of
least 10 screws.
the appliance from the inside.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Attaching and aligning the
custom door front
^ Put the side strips m back into place
and screw them completely down on
both sides of the appliance door.
Bag E contains spare screws for this
purpose.
^ Screw the nuts o a few turns onto
the threaded bolts n. Do not tighten
the nuts completely.
^ Close the appliance door and check
the distance to doors of adjacent
furniture/fixtures.
^ Insert the angle trim m as far as it will
go in the spaces provided in the
mounting frame.
^ Align the custom door height with the
threaded bolts n.
^ Align the appliance door depth with
the recesses in the angle trim m.
Then screw the angle trims into
position.
^ Now tighten the nuts o on top. This
secures the appliance door.
^ Open the door and hang the custom
door with the mounting frame over
the threaded bolts n.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Attaching the fixing brackets
Attaching the covers
(Only for appliances using the "Front
panel gap kit".)
^ To mount the cover strips on both
sides of the door, click them into
place from bottom to top, into the
gap between the appliance door and
the custom door.
The fixing brackets are used to secure
the custom door front to the bottom of
the appliance door.
^ Open the appliance door all the way.
^ Slightly loosen the screw (1.).
^ Position the fixing bracket on the
appliance door (2.) and pre-drill a
hole in the custom door front.
^ Screw the fixing bracket securely to
the custom door front (3.).
^ Tighten the screw (4.).
^ Put the cover on the bracket (5.).
The number of lower brackets will
depend on the width and the design of
the custom door.
^ Screw the brackets onto both sides
of the appliance, to hold the cover
strip.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
Attaching the toe-kick cover
The maximum height of the toe-kick
cover is 4" (101 mm) from the top of
the floor. Do not cover the ventilation
slits in the plinth. Risk of damage to
the appliance.
^ If required, cut the toe-kick cover to
the required length and height.
^ Insert the cover strip into the space
between the appliance and the
wooden panel.
For side-by-side combinations, the
cover strips (on both sides of the
appliance) are applied to the
outermost spaces only.
^ Attach the plinth to the appliance,
and put the included cover plates in
place.
^ Attach the light switch cover.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the appliance
^ Remove the foil from the adhesive
strips.
^ Attach the toe-kick cover to the
plinth.
Mounting the air separator
The air separator keeps the supply and
exhaust air separate. This prevents
warm exhaust air from flowing into the
machine, optimizing the energy
performance of the unit.
^ Position the air separator in the
center of the appliance door.
^ From below, screw the air separator
firmly onto the door with the 2
screws.
^ If necessary, shorten the three parts
of the air separator.
^ Insert the foam pieces back into the
sides.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
The appliance is supplied with a
UL-listed, 3-wire power cord and
NEMA 5-15 P plug ready for connection
to a 120 V, 60 Hz supply.
, Avoid the risk of electrical
shock
- Plug into a grounded 3-prong
outlet.
The fuse rating is 15 amps.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
The appliance requires a 3-wire
receptacle.
The receptacle must be installed by a
licensed electrician only.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
In the case of side-by-side installations,
a separate outlet must be used for each
appliance. Ideally, the power outlet
should be next to the appliance and
easily accessible. Do not connect the
appliance to the power supply by an
extension cord. Extension cords do not
guarantee the required safety of the
appliance (danger of overheating).
Improper connection of the
equipment grounding conductor
may result in electric shock. If you
are in any doubt as to whether the
appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
If any changes are needed to the
household wiring or power supply, this
work must be performed by a qualified
electrician.
Installation, repairs and other work
by unqualified persons could be
dangerous.
Before installing the appliance,
verify that the voltage, load and
circuit rating information found on
the data plate match the household
electrical supply.
If there are any questions regarding the
electrical connection of this appliance
to the power supply, please consult a
licensed electrician or call the Miele
Technical Service.
U1-800-999-1360
V1-800-565-6435
63
Download from Www.Somanuals.com. All Manuals Search And Download.
RemoteVision (optional accessory)
Miele's RemoteVision Wi-Fi technology
creates a 'virtual link' between your
appliance and our monitoring center. If
a fault occurs, Miele's client service
center will be notified and contact you,
or another trusted individual identified
on your call roster, in order to gain
access to your appliance to fix the
problem.
Be sure your wireless system meets the
following requirements
– A wireless router that supports an
IEEE 802.11b/g protocol
– Windows XP® or newer operating
system, Mac® OS X 10.3 or higher
– Cable or DSL modem
– Microsoft® Internet Explorer 6 or
higher, Safari 2.0 or higher, Firefox
1.5 or higher
For information on set-up and
installation of the RemoteVision module
see the "Installation" section of this
manual.
* Please note that each wireless router
manufacturer supplies their own device
drivers and setup programs. Due to the
differences in manufacturers, exact
router setup instructions are not
included in this manual. Wording and
instructions may vary.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
RemoteVision (optional accessory)
Accessing the RemoteVision
^ Tap the X button until ; appears in
the display.
control panel
^ Touch the access button "p" to
confirm.
See the table on the following page for
a description of each setting in the
display.
^ Touch the access button "p" so it
turns yellow.
^ Use the Y or X buttons to select the
^ Note the position of the X button, but
RemoteVision options.
do not touch.
^ Touch the access button "p" again so
it turns white.
The module has been connected to
the network when ; # appears in the
display.
Only the access button "p" is visible.
If ; # does not appear, refer to the
"Network options" section of the
XKM 2000 Installation Instruction
manual.
^ Place one finger on the position of
the X button and hold (the X button
will not be visible).
^ While holding down the X button,
press the access button "p" once.
Keep holding the X button down until
the following appears in the display
(approx. 5 seconds).
^ Press and hold the access button "p"
for 2 seconds to confirm the change.
^ To return to the main menu, tap the X
button until a solid ; - appears in the
display.
^ Press the access button "p" to
confirm.
^ Tap the X button until a ; appears in
Access to the Custom settings mode is
now active for approximately 10
seconds.
the display.
^ Touch the access button "p".
You have left the Custom settings
mode.
When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
RemoteVision (optional accessory)
MasterCool control panel options for RemoteVision
Status indicators Description of function
Flashing ; ~
Flashing ; ‡
Flashing ; |
Module booting phase
Not connected to network
Connection to network established, no IP address
assigned
Solid
; #
Connected to network
Flashing ; <
In Ad-Hoc Mode, not connected
In Ad-Hoc Mode, connected
Flashing ; =
Selectable
options
Description of function
; -
; 2
; 3
; 4
Back
Reboot the module
Reset to factory settings
Enter Ad-Hoc Mode
Note: If you cannot select any option (other than ; - "Back", the module has not
been installed correctly.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
K 1803 Vi, K 1813 Vi
K 1903 Vi, K 1913 Vi
en - US, CA
M.-Nr. 10 101 850 / 00
Download from Www.Somanuals.com. All Manuals Search And Download.
|