Operating instructions
for dishwashers
To avoid the risk of accidents or
damage to the appliance it is
essential to read these instructions
as well as the installation plan before
it is installed and used for the first time.
G
M.-Nr. 06 702 810
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Adding detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Selecting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Starting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programme sequence indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
At the end of a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Switching off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Unloading the dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Interrupting a programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Changing a programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Tab function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Delay start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Factory default setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Adjust sensor wash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cleaning the wash cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cleaning the door and the door seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cleaning the door front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Cleaning the control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cleaning the filters in the wash cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Cleaning the spray arms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
The dishwasher does not fill/drain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Unsatisfactory washing result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Problem solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cleaning the water inlet filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cleaning the drain pump and non-return valve. . . . . . . . . . . . . . . . . . . . . . . . . . . 53
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
For testing institutes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Connection to the water supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the appliance
Appliance overview
aUpper spray arm (not visible)
bCutlery tray (depending on model)
cUpper basket
gFilter combination
hData plate
iChild safety lock in door grip (not
visible)
dMiddle spray arm
jRinse aid reservoir
eAir inlet for drying
(depending on model)
kDual compartment detergent
dispenser
fLower spray arm
lSalt reservoir
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the appliance
Control panel
aProgrammes
fCheck/Refill indicators
bDisplay
gStart/Stop button with indicator light
cTab indicator
hDelay start button
with indicator light
dProgramme sequence indicators
eOn/Off button s
iTab button
jProgramme selector button
This instruction book applies to several different dishwasher models.
The specific dishwasher models below are referred to as follows:
G 1220 etc. = G 1XXX
G 2220 etc. = G 2XXX
The model numbers G 1XXX and G 2XXX used in this book refer to the model
designation specified on the data plate of the appliance (and not the
description on the control panel).
The data plate is located at the top right hand side of the door.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Delivery
This appliance conforms to current
Before setting up the appliance,
check it for any externally visible
damage. Under no circumstances
should you use a damaged appliance.
A damaged appliance could be
dangerous.
safety requirements. Inappropriate
use can, however, lead to personal
injury and damage to property. To
avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time. They
contain important information on its
safety, use and maintenance.
Please ensure that the packaging
material is offered for recycling.
Keep these instructions in a safe
place for future reference, and pass
them on to any future user.
Installation
The dishwasher must be installed
and connected in compliance with
the installation plan.
Correct usage
The dishwasher must only be
plugged into the electricity supply
via a suitable switched socket. The
electrical socket must be easily
accessible after the dishwasher is
installed so that it can be disconnected
from the electricity supply at any time.
(See "Electrical connection").
This dishwasher is intended
exclusively for cleaning domestic
crockery and cutlery in a domestic
household. Using it for purposes other
than those for which it was designed,
as well as any alterations or
conversions to the appliance would be
unauthorised and could cause harm.
The manufacturer cannot be held liable
for damage resulting from improper or
incorrect use of the appliance.
There must be no electrical
sockets behind the dishwasher.
Danger of overheating and fire risk if
the dishwasher were to be pushed up
against a plug.
Transport
In order to ensure stability,
built-under and integrated
dishwashers must only be installed
under a continuous worktop which is
secured to adjacent cabinetry.
Should you ever need to move the
dishwasher, e.g. when moving
house, note the following:
– Empty the dishwasher,
– Secure any loose parts, e. g. hoses,
mains cable, cutlery baskets, lower
basket
– Transport the dishwasher in the
upright position only.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
The dishwasher must not be
installed under a hob. The high
This equipment may only be used
in mobile installations such as
radiant temperatures which are
ships, caravans, aircraft etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.
sometimes generated by a hob could
damage the dishwasher. For the same
reason it should not be installed next to
open fires or other appliances which
give off heat, such as heaters etc.
A damaged appliance could be
dangerous. Switch off at the mains
and call your Miele supplier or the Miele
Service Department.
If you want to convert your
freestanding dishwasher to a
built-under ("U") model, you will need to
order the appropriate conversion kit. If
you remove the existing plinth, you
must replace it with a U-model plinth.
This is necessary to avoid the risk of
injury caused by protruding metal
parts.
The plastic housing of the water
connection contains an electrical
component. The housing must therefore
not be dipped in water.
There are live wires in the water
inlet hose. Never cut the water inlet
hose, even if it is too long.
Do not connect the dishwasher to
the mains supply until it has been
fully installed.
Do not connect the appliance to
the mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
appliance (e.g. danger of overheating).
Before connecting the appliance,
check that the connection data on
the data plate (voltage and connected
load) match the mains electricity
supply. If in any doubt, consult a
qualified electrician.
Use
Do not use solvents in the
dishwasher. Danger of explosion.
The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system. It is most important that this
basic safety requirement is regularly
tested and where there is any doubt,
the electrical system in the house
should be checked by a qualified
electrician.
Do not inhale or ingest dishwasher
detergent! Dishwasher detergents
can cause burning in the nose, mouth
and throat if swallowed, or inhibit
breathing. Consult a doctor immediate-
ly if detergent has been swallowed or
inhaled.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Avoid leaving the door open
unnecessarily, as you could trip
On models with "Delay start", make
sure that the dispenser is dry
over it.
before adding detergent. Wipe dry if
necessary. Detergent will clog if poured
into a damp dispenser and may not be
thoroughly dispensed.
Do not use liquid detergent when
selecting Delay start, as it can run into
the dishwasher before it is required.
Do not sit or lean on the opened
door. This could cause the
dishwasher to tip and be damaged and
you could get injured.
Only use detergent and rinse aid
formulated for domestic
dishwashers. Do not use washing-up
liquid.
Safety with children
This appliance is not a toy! To
avoid the risk of injury do not allow
children to play in or around the
dishwasher, or to operate it. There is
also a danger that children playing
might shut themselves in the
dishwasher.
In an appliance with a cutlery
basket (depending on model)
cutlery is cleaned and dried more
efficiently if placed in the basket with
the handles downwards. However, to
avoid the risk of injury place knives and
forks etc. with the handles upwards.
Keep children away from
detergents. Dishwasher detergents
can cause burning in the mouth, nose
and throat if swallowed, or inhibit
breathing. Keep children away from the
dishwasher when the door is open.
There could still be detergent residues
in the cabinet.
Please only use special coarse
grained dishwasher salt for
reactivation, as other salts may contain
insoluble additives which can impair
the functioning of the softener.
Plastic items which cannot
withstand being washed in hot
water, such as disposable plastic
containers, or plastic cutlery and
crockery should not be cleaned in the
dishwasher. The high temperatures in
the dishwasher may cause them to melt
or lose shape.
Consult a doctor immediately if your
child has swallowed or inhaled
detergent.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
To avoid damage to the
appliance and other materials
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any
damage caused by cockroaches or
other vermin will not be covered by the
guarantee.
Do not fill the rinse aid reservoir
with powder or liquid detergent.
This will cause serious damage to the
reservoir.
Inadvertently filling the salt
reservoir with powder or liquid
dishwasher detergent always leads to
serious damage to the water softener.
Make sure you have picked up the
correct packet of dishwasher salt
before filling the salt reservoir!
Repairs and maintenance
Repairs may only be carried out by
suitably qualified and competent
technicians in accordance with current
local and national safety requirements.
Repairs and other work by unqualified
persons could be dangerous.
Do not use commercial or industrial
detergents as these may damage
material and there is a risk of severe
chemical reaction.
Always disconnect the appliance
from the electrical supply for
maintenance work (switch off at the wall
socket and remove the plug).
The Miele Waterproof System offers
protection from water damage,
provided the following conditions are
met:
If the connection cable is damaged
it must be replaced with a Miele
cable by a Miele approved service
technician only.
– The dishwasher is correctly installed
and plumbed in.
– The dishwasher is properly
maintained and parts are replaced
where it can be seen that this is
necessary.
Disposal of your old appliance
When disposing of an old
dishwasher first make it unusable.
Disconnect, cut off the cable and the
plug from the cable. Make the door lock
inoperative by unscrewing the Torx
screw, so that children cannot
accidentally shut themselves in. Make
appropriate arrangements for the
disposal of the appliance.
– The stopcock has been turned off
when the appliance is not used for a
longer period of time (e.g. during
holidays).
The Waterproof system will work even if
the appliance is switched off. However,
the appliance must remain connected
to the electricity supply.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
It should be unplugged or
disconnected from the mains electricity
supply by a competent person. The
plug must be rendered useless and the
cable cut off directly behind it to
prevent misuse. See the "Warning and
Safety" section of this booklet for further
details.
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled. Ensure
that any plastic wrappings, bags etc.
are disposed of safely and kept out of
the reach of babies and young
Energy saving washing
children. Danger of suffocation!
Rather than just throwing these
This dishwasher is exceptionally
materials away, please ensure that they economical in its use of water and
are recycled.
electricity. You can make the most of
your appliance by following these tips:
Disposal of your old appliance
^ If your household water system is
suitable, this dishwasher can be
connected to a hot water supply, for
further economies. If the water is
heated by for example, solar panels,
this would be energy efficient.
However, if your water is heated by
electricity we would recommend
connection to cold water.
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of your
old appliance with your household
waste.
^ For most economical dishwashing
make full use of the baskets without
overloading the dishwasher.
^ Choose the programme to suit the
type of crockery being washed and
the degree of soiling.
^ Select the Energy save programme
for energy-saving dishwashing.
^ Follow the detergent manufacturer’s
recommendations on detergent
dosage.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
^ When using powder or liquid
detergent you can use 1/3 less
detergent if baskets are only half full.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
To open the door
Child safety lock
^ Press the release catch inside the
door grip and pull forward.
Use the child safety lock to prevent
children opening the dishwasher door.
If the door is opened during operation
all functions are automatically
interrupted.
^ To lock the door, push the slide
underneath the door grip to the right.
^ To unlock the door, push the slide to
the left.
To close the door
^ Push the baskets right in.
^ Then lift the door upwards and push
until it clicks into position.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Water softener
The dishwasher is programmed at
the factory for a water hardness level
of 2.7 mmol/l (15 °d).
In order to achieve good cleaning
results, the dishwasher needs to
operate with soft water. Hard water
results in the build-up of calcium
deposits on crockery and in the
dishwasher.
Mains water with a hardness level
higher than 0.7 mmol/l (4 °d - German
scale) needs to be softened. This takes
place automatically in the integrated
water softener.
If this setting corresponds to the
hardness of your water you do not need
to do anything more.
If your water is harder or softer, you will
need to programme the water hardness
level. See following section.
– The water softener requires
dishwasher salt.
If you use "3 in 1" products in your
dishwasher, you should still add salt
in order to achieve optimum results.
– The dishwasher must be
programmed for the water hardness
in your area.
– Your local water authority will be able
to advise you of the water hardness
level in your area.
Where the water hardness fluctuates
e.g. between 6.7 - 9.0 mmol/l (37 -50 °d
- German scale) always programme the
dishwasher to the higher value
(9.0 mmol/l in this example).
In the event of a fault, it will help the
service technician if you know the
hardness of your local water supply.
^ Enter the water hardness below:
mmol/l or °d
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
To programme the water hardness
level
The characters "p 1 5" will flash one
after the other in the display.
This means that the water hardness
level has been set at 15 °d (2.7 mmol/l)
(factory setting).
Each time a button is pressed one of
the indicator lights will flash and light
up in the control panel. However, only
the indicator lights mentioned in the
following programming process stages
are significant.
The value which has been set for the
water hardness is shown as a figure
after the "p" in the display (see chart).
^ Use the Start/Stop button to select
the value which equates to your
water hardness level.
Each press on the button moves you
up a level. When the highest water
hardness level is reached, the setting
starts from the beginning again.
The programming procedure can be
cancelled at any time by pressing the
On/Off button s. The procedure can
then be re-started from the beginning
again.
^ Switch the dishwasher off with the
On/Off button s.
^ Switch the dishwasher off with the
On/Off button s.
^ Press the Start/Stop button in and
whilst holding it in switch the
dishwasher on using the On/Off
button s.
Keep the Start/Stop button pressed in
for at least four seconds until the
"Start/Stop" indicator light comes on.
If this does not happen, start the
procedure from the beginning again.
^ Press the Delay start button twice.
The "Delay start" indicator will flash
briefly twice at intervals.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
To call up the water hardness
level in the display
°d
German
scale
mmol/l
°f
Value displayed
^ Switch the dishwasher off with the
On/Off button s.
1
2
3
4
5
6
7
8
9
0.2
0.4
0.5
0.7
0.9
1.1
1.3
1.4
1.6
1.8
2.0
2.2
2.3
2.5
2.7
2.9
3.1
3.2
3.4
3.6
3.8
4.0
4.1
4.3
4.5
4.7
4.9
5.0
5.2
5.4
5.6
5.8
5.9
6.1
6.3
6.5
6.7-8.1
2
4
5
7
9
1
2
3
4
5
6
7
8
^ Press the Start/Stop button in and
whilst holding it in switch the
dishwasher on using the On/Off
button s.
Keep the Start/Stop button pressed in
for at least four seconds until the
"Start/Stop" indicator light comes on.
11
13
14
16
18
20
22
23
25
27
29
31
32
34
36
38
40
41
43
45
47
49
50
52
54
56
58
59
61
63
65
66-80
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37-45
46-60
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
45
60
70
^ Press the Delay start button six times.
The "Delay start" indicator will flash
briefly six times at intervals.
Characters will flash in sequence in the
display.
The figure(s) after the "p" is the value for
the water hardness level which has
been set (see chart).
^ Switch the dishwasher off with the
On/Off button s.
8.3-10.8 82-107
61-70 11.0-12.6 109-125
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Before using the appliance for
the first time you require:
If the water in your area is very soft
and constantly lower than
0.7 mmol/l (4 °d) you do not need
to add dishwasher salt.
The water softener must, however,
still be programmed to correspond
to the water hardness level in your
area.
– approx. 2 litres of water,
– approx. 2 kg dishwasher salt,
– domestic dishwasher detergent,
– rinse aid formulated for domestic
dishwashers.
Important: Before filling the salt
reservoir with dishwasher salt for the
first time, you must fill it with
approx. 2 litres of water to enable
the salt to dissolve. Once the
dishwasher has been used, there is
always sufficient water in the
reservoir.
Every dishwasher is tested at the
factory.
There will be residual water in the
appliance from this test. It is not an
indication that it has been previously
used.
Filling the salt reservoir
,Inadvertently filling the salt
reservoir with powder or liquid
The water softener requires
dishwasher salt. If you use "3 in 1"
tablets in your dishwasher you
should still add salt in order to
achieve optimum results. The
amount of salt used is reduced to
between 1/4 and 1/3 of the normal
amount if the "3 in 1" function is
selected.
dishwasher detergent always leads
to serious damage to the water
softener. Make sure you have picked
up the correct packet of dishwasher
salt before filling the salt reservoir!
,Only use special coarse grained
dishwasher salt for reactivation. Do
not use other salts such as cooking
salt, agricultural grade or gritting
salt. These may contain insoluble
additives which can impair the
functioning of the water softener.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
^ Remove the lower basket and
unscrew the salt reservoir cap.
Salt indicator
Only open the salt reservoir when
you want to fill it with dishwasher salt
as water or salt solution will run out
of the reservoir when the cap is
removed.
^ Fill the reservoir with approx. 2 litres
of water (first use only).
^ Fill the salt reservoir with dishwasher
salt when the salt indicator light
comes on. (If it comes on during a
programme, wait until the end of the
programme).
After the reservoir has been filled, the
water softener is automatically
reactivated the next time the
dishwasher is run. The salt indicator
light may still be illuminated during this
process. It will go out once the salt
concentration has reached the correct
level.
^ Place the funnel provided over the
salt reservoir and carefully fill with salt
until the reservoir is full. The salt
reservoir holds approx. 2 kg of salt
depending on the brand used.
,After filling the salt reservoir, run
the "Quick wash" programme
immediately (without any crockery in
the dishwasher) to remove any
traces of salt water from the cabinet.
As the salt reservoir is filled, displaced
water will overflow.
^ Clean any excess salt from around
the reservoir opening and then screw
the cap on again firmly.
^ Run the "Quick wash" programme
immediately (without any crockery in
the dishwasher) to remove any traces
of salt water from the cabinet.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Rinse aid
Adding rinse aid
Rinse aid is necessary to ensure water
does not cling and leave marks on
crockery during the drying phase and
helps crockery dry faster after it has
been washed.
Rinse aid is poured into the storage
reservoir and the amount set is
dispensed automatically.
,Inadvertently filling the rinse aid
reservoir with powder or liquid
detergent always causes serious
damage to the reservoir. Only pour
rinse aid formulated for domestic
dishwashers into the reservoir.
^ Press the button on the lid of the
rinse aid reservoir in the direction of
the arrow until the flap springs open.
Alternatively, it is possible to use
– Household vinegar with a max. 5%
acid content
or
– Liquid citric acid up to 50% acid
content.
The resulting rinsing and drying quality
will not, however, be as good as when
rinse aid is used.
,Do not use vinegar with a higher
acid content (e.g. vinegar essence
25% acid). This would damage the
dishwasher.
If you only ever use "2 in 1" or "3 in 1"
products in your dishwasher you do
not need to add rinse aid.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Rinse aid indicator
When the light comes on the reservoir
contains sufficient rinse aid for 2 - 3
programmes only.
^ Add rinse aid only until it is visible in
the opening.
The rinse aid reservoir holds approx.
110 ml.
^ Add rinse aid in plenty of time.
^ Close the flap firmly so that it clicks
into place. Otherwise water would
enter the rinse aid reservoir during a
programme.
If the "2 in 1" or "3 in 1" function has
been selected, the Rinse aid
indicator does not light up (see
"Operation - Tab function").
^ Wipe up any spilled rinse aid. This
prevents over-foaming occurring
during the next programme.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Setting the rinse aid dosage
^ Press the Delay start button three
times.
You can adjust the rinse aid dosage for
best results.
The "Delay start" indicator will flash
briefly three times at intervals.
The rinse aid dosage can be set from
approx. 0-6 ml. It is set to a
recommended setting of approx. 3 ml
at the factory.
p 3 will flash in the display.
This means that the rinse aid dosage
has been set at 3 ml at the factory.
If spots appear on crockery and
glassware:
The dosage set will show in the display
after the p.
^ Increase the rinse aid dosage.
^ Use the Start/Stop button to select
the rinse aid dosage you want.
The dosage amount alters each time
you press the button.
If clouding or smearing appears on
crockery and glassware:
^ Decrease the rinse aid dosage.
The programmed rinse aid dosage is
now stored in memory.
^ Switch the dishwasher off with the
^ Switch the dishwasher off with the
On/Off button s.
On/Off button s.
^ Press the Start/Stop button in and
whilst holding it in switch the
dishwasher on using the On/Off
button s.
Keep the Start/Stop button pressed in
for at least four seconds until the
"Start/Stop" indicator light comes on.
If this does not happen, start the
procedure from the beginning again.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
Note
– Deep based items should be placed
at an angle so that water can run off
them freely.
Remove coarse food residues from
crockery.
– The spray arms must not be blocked
by items which are too tall or hang
through the baskets.
There is no need to rinse items under
running water.
If in doubt, test for free movement by
manually rotating the spray arms.
,Do not wash items soiled with
ash, sand, wax, lubricating grease
or paint in the dishwasher. Ash does
not dissolve and is distributed in the
wash cabinet. Wax, sand, lubricating
grease and paint cause damage to
the dishwasher.
– Make sure that small items cannot
fall through the holders in the
baskets. Small items, e.g. lids,
should therefore be placed in the
cutlery tray or cutlery basket
(depending on model).
Crockery can be loaded anywhere in
the baskets, but the following notes
should be observed:
Some foodstuffs may contain natural
dyes, e.g. carrots, tomatoes or
ketchup. Plastic items in the
dishwasher may discolour if large
quantities of these foodstuffs find
their way into the appliance on the
crockery. The stability of plastic
items is not affected by this
discolouration.
– Do not place crockery and cutlery
inside other pieces where they may
be concealed.
– Load the crockery so that water can
access all surfaces. This ensures
that it is properly cleaned.
– Make sure that all items are securely
positioned.
– Hollow items such as cups, glasses,
pans, etc. must be inverted in the
basket.
– Tall, narrow, hollow items, e.g.
champagne glasses, should be
placed in the centre of the basket to
ensure better water coverage.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
Items not suitable for
dishwashers:
We recommend:
– When purchasing new crockery and
cutlery, make sure they are
dishwasher-proof.
– Wooden cutlery and crockery or
items with wooden parts: these may
discolour and fade. The glue used in
these items is not dishwasher-proof
and wooden handles may come
loose after being washed in a
dishwasher.
– If delicate glassware is washed in the
dishwasher ensure that only very low
temperatures are used (see
programme chart), or a special
glass-care programme is used
(depending on model). This will
reduce the risk of clouding.
– Craft items, antiques, valuable vases
and decorative glassware are also
not suitable for dishwashers.
– Wash particularly delicate glassware
by hand.
– Plastic items which are not heat
resistant. The high temperatures in
the dishwasher may cause them to
melt or lose shape.
Please note
Silverware previously cleaned with a
silver polish may still be damp or
spotted at the end of a programme,
where water has not run off smoothly. It
may need rubbing dry with a soft cloth.
– Copper, brass, tin and aluminium
items may discolour or become matt.
– Colours painted over a glaze may
fade after a number of washes.
Silver which has been in contact with
foods containing sulphur can discolour.
These include egg yolk, onions,
mayonnaise, mustard, pulses, fish, fish
brine and marinades.
– Clouding may occur on glasses after
frequent washing. Do not wash
delicate glassware, or glassware
containing lead crystal in a
dishwasher.
,Aluminium components (e.g.
grease filters) must not be cleaned
with caustic alkaline commercial or
industrial cleaning agents. These
may damage the material, or in
extreme cases, cause a severe
chemical reaction. See section
"Adding detergent" for information
on suitable detergents.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
Upper basket
Hinged cup rack
^ To make room for tall items raise the
rack upwards.
,For safety reasons, do not
operate the dishwasher without the
upper and lower baskets in place.
Positioning rail (depending on model)
Glasses can be arranged along the
positioning rail to give them some
support during the programme.
^ Use the upper basket for small,
lightweight and delicate items such
as cups, saucers, glasses, dessert
bowls, etc. Shallow pans or casserole
dishes can also be placed in the
upper basket.
^ Raise the rail, and lean the glasses
against it.
The positioning rail can be flipped over
to the middle of the basket for easy
sorting and removing of crockery.
^ Long items such as soup ladles,
mixing spoons and long knives
should be placed lying down across
the front of the upper basket.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
Adjusting the upper basket
Depending on the setting of the upper
basket, the following plate dimensions
can be accommodated.
In order to gain more space for taller
pieces of crockery in the bottom or
upper basket, the upper basket can be
adjusted on three levels with 2 cm
between each level.
Dishwasher with cutlery tray
(see data plate for model number)
Upper
basket
level
Plate Ø in cm
The upper basket can also be set at an
angle with one side high and the other
side low. Ensure however, that the
basket can slide smoothly into the
cabinet. It is better to adjust the basket
before loading it.
Upper basket
Lower
basket
G1XXX G2XXX
Top
15
17
19
19
21
23
31
29
27
Middle
Bottom
^ Pull out the upper basket.
Dishwasher with cutlery basket
(see data plate for model number)
Upper
basket
level
Plate Ø in cm
Upper basket
Lower
basket
G1XXX G2XXX
Top
20
22
24
24
26
28
31
29
27
Middle
Bottom
^ Pull upwards on the levers at either
side of the upper basket.
^ Adjust the basket to the desired
height.
^ Then push the levers securely back
down into position.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
Lower basket
Hinged spiked insert
For larger and heavier items such as
plates, serving platters, saucepans,
bowls, etc.
This insert is used for washing plates
and saucers.
Small items such as saucers can also
be placed in the lower basket.
Do not place thin, delicate glassware in
the lower basket.
Both sides of the rear section of the
spiked insert can be lowered to make
more room for large items, e.g. pots,
pans and dishes.
Dishwashers with cutlery tray
^ Press the yellow lever downwards a
and then lower the spikes b.
Dishwashers with cutlery basket
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
To remove the hinged spike insert
Bottle holder (depending on model)
You can remove the spiked insert to
make more room for larger items of
crockery, e.g. a large, shallow pot, or
for another type of insert.
The bottle holder can be used to wash
narrow items, e.g. milk and baby
bottles.
^ Place the bottle holder as shown in
the bottom basket. If placed
To remove an insert a
anywhere else, water will not be able
to access the bottle properly, and
cleaning results will be impaired.
^ Pull upwards by the handle as
shown.
To refit it b
^ Fit the insert into the lower basket
with the hooks going under the long
cross piece as illustrated.
^ Press down on the handle until the
insert is securely held in position.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
Cutlery
Cutlery tray (depending on model)
If spoon handles do not fit between the
holders, then place them the other way
round.
^ Arrange the cutlery in the tray as
shown.
To make unloading much easier, cutlery
should be grouped in zones, one for
knives, one for forks, one for spoons,
etc.
Spoon heads should be placed in
contact with at least one of the serrated
retainers on the base of the cutlery tray
to ensure that water runs off them freely.
The upper spray arm must not be
blocked by items which are too big
(e.g. cake slices).
The cutlery tray insert is removable.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the dishwasher
Cutlery basket (depending on model)
^ Fit it into the cutlery basket if
required.
^ To avoid the risk of injury, knives and
forks should be placed with the
handles upwards in the basket.
However, cutlery placed handle
down in the basket will come out
cleaner and drier.
^ Place small spoons in the individual
slots to either side of the cutlery
basket.
Cutlery insert for the cutlery basket
Use the insert supplied for heavily
soiled spoons.
The insert separates the items so that
they can be more easily accessed by
water.
^ Insert cutlery with the handles facing
downwards, and distribute them
evenly along the insert.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Detergent
,Avoid inhalation of powder
,Only use detergents formulated
for domestic dishwashers. Do not
use washing up liquid.
detergents and do not ingest
dishwasher detergent. Dishwasher
detergents can cause burning in the
nose, mouth and throat if swallowed,
or inhibit breathing. Consult a doctor
immediately if detergent has been
swallowed or inhaled.
^ You can use conventional powder
detergent, tablets or liquid
dishwasher detergent.
Refer to the dosing instructions given
by the manufacturer on the
packaging.
Keep detergent and other
household agents out of the reach of
children at all times. Keep children
away from the dishwasher when the
door is open. There could still be
detergent residues in the cabinet. To
avoid the danger of children coming
into contact with the dishwasher
detergent, only add detergent just
before starting the programme and
close the door, activating the child
safety lock (if your dishwasher is
fitted with one).
^ Put the detergent into the dispenser
compartment.
^ Do not use tablet detergent on the
"Quick" programme, as the tablets
will not dissolve properly.
Failure to dispense the
recommended amount of detergent
may impair cleaning results.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Adding detergent
For information
Compartment I holds max. 10 ml,
Compartment II holds max. 50 ml.
There are markings in compartment II
to assist with dispensing: 20, 30. The
marks indicate a level of approx. 20 or
30 ml when the door is open in a
horizontal position.
^ Press the opening catch on the
detergent dispenser. The flap will
spring open.
The flap is always open at the end of a
programme.
^ Add the required amount of
detergent and close the flap.
^ Make sure that the detergent
packaging is properly closed after
use to avoid it getting damp and
becoming lumpy.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Switching on
Starting a programme
^ Make sure the spray arms are not
obstructed.
^ Select the programme required using
the programme selector button.
^ Close the door.
The indicator light for the programme
selected comes on.
The programme duration will appear in
the hours and minutes in the display.
^ Open the stopcock, if it is closed.
^ Switch the dishwasher on with the
On/Off button s.
You can now select an additional
function (see "Additional functions").
The Start/Stop indicator light flashes
and the indicator light comes on next to
the last programme selected.
^ Press the Start/Stop button.
The programme cycle will begin. The
Start/Stop and Wash/Rinse indicators
and the indicator for the programme
selected will light up.
Selecting a programme
Choose your programme according to
the type of load and how dirty it is.
If the "2 in 1-Tab" or "3 in 1-Tab" function
has been selected, the corresponding
indicator will light up as well.
The different programmes and their
uses are described in the programme
chart later on in this booklet.
A programme can only be cancelled
in the first few minutes. Otherwise
the programme must continue to the
end so that important programme
stages (e.g. reactivating the water
softener) are not omitted.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Display
At the end of a programme
The duration of the programme
selected appears in hours and minutes
in the display before the programme
begins. During the programme, the
time left until the end of the programme
is displayed.
A programme has finished when a "0"
appears in the display and the "End"
programme sequence indicator lights
up.
The dishwasher can now be opened
and unloaded (see "Unloading the
dishwasher").
The time displayed may vary with the
same programme. This is partly
because of the water inlet temperature
at each intake, and partly because of
the amount and soiling level of the
crockery.
,To prevent the risk of steam
damage to the worktop edging
above the dishwasher, it is advisable
to leave the door closed until you are
ready to unload the crockery.
Alternatively you can open the door
fully until the crockery is cool
enough to unload. Do not leave the
door only partially open.
When a programme is selected for the
first time, the display shows an average
time for a cold water intake.
The times shown in the programme
chart refer to standard test loads and
temperatures.
Switching off
Each time a programme is run, the
electronic unit takes the new conditions
into account, and calculates the time
required.
At the end of a programme:
^ Switch the dishwasher off with the
On/Off button s.
The dishwasher will continue to use
electricity until the On/Off button s
is switched off.
Programme sequence
indicators
After a programme has been started,
the current stage of the programme is
indicated by the programme sequence
indicator lights.
If the dishwasher is not to be used for a
longer period of time, e. g. whilst on
holiday, the stopcock should be turned
off.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Unloading the dishwasher
Interrupting a programme
Dishes tend to break and chip more
easily when they are hot.
Allow the dishes to cool until they are
comfortable enough to handle before
unloading them.
A programme is interrupted as soon as
the door is opened.
If the door is closed again, the
programme will continue from the point
it was at before the door was opened.
If you open the door fully after switching
off, the dishes will cool much faster.
,Water in the dishwasher may be
hot. Danger of scalding!
^ First unload the lower basket, then
the upper basket and cutlery tray
(depending on model).
This will prevent water drops from the
upper basket and cutlery tray from
falling onto the dishes in the lower
basket.
Only open the door if absolutely
necessary and exercise extreme
caution when doing so. Before
closing the door again, leave it ajar
for approx. 20 seconds. This will
enable the temperature in the wash
cabinet to settle. Then close the
door firmly making sure that it clicks
into place.
Changing a programme
Important:
If the detergent dispenser flap has
already opened, do not change the
programme.
If a programme has already started and
you wish to change it, proceed as
follows:
^ Press the Start/Stop button for at
least one second.
The programme will be cancelled.
^ Select the programme you want and
then start it.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Additional functions
Do not select the "3 in 1" function if:
– using "2 in 1" tabs (detergent with
rinse aid)
Tab function
– your water hardness level is above
3.8 mmol or 21 °d.
You can programme your dishwasher to
ensure excellent results when using
tablet detergents by simply selecting
the "2 in 1" or "3 in 1" function using the
Tab button.
The programme sequence will be
adjusted to the type of detergent
selected. Depending on the
Follow the detergent manufacturer's
instructions.
The washing and drying
performance of these types of
detergent can vary enormously.
programme, the duration can be
considerably longer.
^ Switch the dishwasher on with the
On/Off button s.
"2 in 1":
The Start/Stop indicator light will flash.
When the "2 in 1" function is selected,
the programme sequence is adjusted
for "2 in 1" tabs (detergent containing
rinse aid).
The dispensing of rinse aid and the
rinse aid refill indicator light are
deactivated.
^ Press the Tab button until the
detergent type of your choice ("2 in 1"
or "3 in 1") lights up.
If neither of the indicators lights up, the
dishwasher is set for normal detergent.
The function selected is active on all
programmes until the setting is
changed.
"3 in 1":
When the "3 in 1" function is selected,
the programme sequence is adjusted
for "3 in 1" tabs (detergent containing
rinse aid and salt substitutes).
^ You can now start a programme or
switch the dishwasher off using the
On/Off button s.
The dispensing of rinse aid and the
rinse aid refill indicator light are
deactivated.
Salt consumption in the water softener
is reduced to between 1/4 and 1/3 of the
normal amount.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Delay start
^ Switch the dishwasher on with the
On/Off button s.
The start time of a programme can be
delayed, e.g. to benefit from economy
rates of electricity. A delay start time of
between 30 minutes and 24 hours can
be selected.
The Start/Stop indicator light will flash.
^ Select the programme required using
the programme selector button.
^ Press the Delay start button.
With a delay start time of between
30 minutes and 9 hours 30 minutes, the The last Delay start time used will
time is set in 30 minute stages. For
10 hours or more it is set in one hour
stages.
appear in the display. The Delay Start
indicator light comes on.
^ Set the time required using the Delay
start button.
When using the Delay start function,
make sure that the compartment is
dry before adding detergent. Wipe
dry with a cloth if necessary. If the
compartment is wet, powder
detergent can become lumpy and
stick to the dispenser, with the result
that it is not fully dispensed.
^ Press the Start/Stop button.
The Start/Stop indicator light will come
on.
Do not use liquid detergent when
selecting Delay start, as it can run
into the dishwasher before it is
required.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
The time starts counting down until the
programme start time: in 1 hour steps
for delay start periods of over 10 hours,
and in minutes for delay start periods of
under 10 hours.
Starting a programme before the
Delay start period has elapsed
A programme can be started before the
Delay start period has elapsed.
Proceed as follows:
At the end of the delay period, the
programme selected begins
automatically. The time left for a
programme to run then shows in the
display, the Delay start indicator light
goes out and the Start/Stop indicator
light comes on.
^ Press the Start/Stop button for at
least one second.
The Delay start indicator light will go out
and the Start/Stop indicator light will
flash.
^ Press the Start/Stop button again.
The programme cycle will begin. The
Start/Stop indicator light will light up
constantly.
How the Delay start time is shown in
the display:
up to 59 minutes:
e.g. 30 minutes = 30
between 1 hour and 9 hours 30
minutes:
e.g. 5 hours = 5.00
10 hours and over:
e.g. 15 hours = 15^
,To prevent children coming into
contact with dishwasher detergent
do not fill the detergent dispenser
until just before starting the
programme, i.e. before pressing the
Start/Stop button, and activate the
child safety lock.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Factory default setting
The characters flashing in the display
show whether a setting other than the
factory default setting has been set.
If you have altered any settings from
the factory default, you can re-set them
back to the factory default settings as
follows:
– "p 1": All settings are set to factory
default settings.
^ Switch the dishwasher off with the
On/Off button s.
– "p 0": At least one setting has been
changed.
^ Press the Start/Stop button in and
whilst holding it in switch the
dishwasher on using the On/Off
button s.
Keep the Start/Stop button pressed in
for at least four seconds until the
Start/Stop indicator light comes on.
^ Press the Start/Stop button if you
wish to re-set all the factory default
settings.
^ Switch the dishwasher off with the
On/Off button s.
If this does not happen, start the
procedure from the beginning again.
^ Press the Delay start button twelve
times.
The Delay start indicator light will give
one long flash and two brief flashes at
intervals and "p 0" or "p 1" will flash in
the display.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Adjust sensor wash
The characters flashing in the display
show whether the "Adjust sensor wash"
function is activated or deactivated.
You can adjust the sensor wash
programme so that it will remove
stubborn soiling in a lightly soiled load.
– "p 1": The "Adjust sensor wash"
function is activated.
^ Switch the dishwasher off with the
On/Off button s.
– "p 0": The "Adjust sensor wash"
function is deactivated.
^ Press the Start/Stop button in and
whilst holding it in switch the
dishwasher on using the On/Off
button s.
Keep the Start/Stop button pressed in
for at least four seconds until the
"Start/Stop" indicator light comes on.
^ To change the setting, press the
Start/Stop button.
Switch the dishwasher off with the
On/Off button s.
If this does not happen, start the
procedure from the beginning again.
^ Press the Delay start button five
times.
The "Delay start" indicator will flash
briefly five times at intervals.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the door front
Check your dishwasher regularly
(approx. every 4 - 6 months). This
way faults and problems can be
avoided.
,Do not use any cleaning agents
containing ammonia or thinners.
These would damage the surface
structure.
Cleaning the wash cabinet
^ Clean the front using a Miele E-cloth
or with suitable cleaning agent for the
type of material the front is made of.
Follow the manufacturer's
The wash cabinet is largely
self-cleaning, provided that the correct
amount of detergent is always used.
instructions.
If, however, there are limescale or
grease deposits in the cabinet these
can be removed with a proprietary
dishwasher cleaner, such as the Miele
dishwasher cleaner (available from the
Miele UK Spare Parts Department).
^ Door fronts made from wood should
only be cleaned using a damp cloth,
and then dried with a soft cloth.
^ Door fronts made of stainless steel
should be cleaned using a damp
cloth and a little washing up liquid, or
a proprietary non-abrasive cleaning
agent designed specifically for use
on stainless steel.
Cleaning the door and the door
seal
^ Wipe the door seals regularly with a
damp cloth to remove food deposits.
^ To help prevent re-soiling, a
proprietary conditioning agent for
stainless steel, such as Neoblank
(available from the Miele UK Spare
Parts Department) can also be used.
Follow the manufacturer's instructions
on the label and apply sparingly with
an even pressure following the
direction of the grain.
^ When the dishwasher is being
loaded, food and drink residue may
drip onto the sides of the dishwasher
door.
These surfaces are outside the wash
cabinet and are not accessed by
water from the spray arms. Any
soiling should be wiped off these
surfaces before the door is closed.
E-Cloth
^ A microfibre "E-Cloth" is available
from the Miele UK Spare Parts
Department, which is suitable for
cleaning surfaces such as stainless
steel, glass, plastic and chrome
without the use of chemicals.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the control panel
,Stainless steel and aluminium
surfaces and controls are
susceptible to scratching and
abrasion, and must be treated with
due care. They may suffer
,Do not use abrasive cleaning
agents, glass cleaning agents or
all-purpose cleaners. Because of
their chemical composition they
could cause serious damage to
surfaces.
discolouration or damage if soiling is
left on them for too long.
Remove soiling immediately.
Plastic panels:
^ This type of control panel should only
be wiped with a damp cloth or
suitable cleaning agent designed for
use on plastic.
Stainless steel panels:
^ Control panels made of stainless
steel should be cleaned using a
damp cloth and a little washing up
liquid, or a proprietary non-abrasive
cleaning agent designed specifically
for use on stainless steel (do not use
it on the controls).
^ To help prevent re-soiling, a
proprietary conditioning agent for
stainless steel, such as Neoblank
(available from the Miele UK Spare
Parts Department) can also be used.
Follow the manufacturer's instructions
on the label and apply sparingly with
an even pressure following the
direction of the grain.
Aluminium panels:
^ Clean aluminium panels with a damp
cloth and a little washing up liquid.
Aluminium is affected by the way that
light falls on it, by the surrounding
environment and by the angle you
observe it from.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the filters in the wash
cabinet
The filter combination in the base of the
wash cabinet retains coarse soil from
the suds solution, preventing it
accessing the circulation system and
re-entering the cabinet through the
spray arms.
,The dishwasher must not be
used without all the filters in place.
Collection of coarse soil may cause the
filters to clog. The level of soiling and
time it takes before the filters need
cleaning will vary depending on use.
^ Turn the handle anti-clockwise to
release the filter combination a.
^ Lift the filter combination out of the
dishwasher b. Remove any coarse
particles and rinse the filter well
under running water. Use a nylon
brush if necessary.
Check the condition of the filters
regularly and clean them if necessary.
^ Switch the dishwasher off.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
To clean the inside of the filter, the flap
must be opened:
^ Replace the filter combination so that
it lies flat in the base of the wash
cabinet.
^ Press together the catches in the
direction of the arrows a as shown,
and open the filter b.
^ Then turn the handle clockwise to
lock the filter combination in place.
^ Rinse all the filters under running
water.
,Take care when you are fitting
the filter combination that it is
secured in position correctly.
Otherwise coarse soil could get into
the circulation system and cause a
blockage.
^ Then close the flap so that the catch
engages.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the spray arms
^ Remove the lower basket.
Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected
and cleaned regularly (approx. every
4 - 6 months).
^ Switch the dishwasher off.
Remove the spray arms as follows:
^ Take out the cutlery tray (if your
dishwasher is fitted with one).
^ Push the top spray arm upwards to
engage the inner ratchet. Then
unscrew the spray arm.
^ Pull the lower spray arm firmly
upwards to remove it.
^ Push the middle spray arm upwards
a to engage the ratchet. Then
unscrew the spray arm b.
^ Use a pointed object to push food
particles into the spray arm jets.
^ Rinse thoroughly under running
water.
^ Replace the spray arms and check
that they rotate freely.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the aid of the following guide, minor problems can be easily corrected
without calling in a Miele service technician, saving you both time and money.
The following guide may help you to find the reason for a fault, and to correct it.
You should, however, note the following:
,Repairs should only be carried out by a suitably qualified and trained
person in accordance with current local and national safety regulations.
Unauthorised or incorrect repairs could cause personal injury or damage the
appliance.
Technical problems
Problem
Possible cause
Remedy
The Start/Stop indicator The appliance is not
does not flash after the plugged in.
Insert the plug and switch
on at the socket.
dishwasher has been
switched on using the
On/Off button s.
The fuse is defective or
has tripped.
Reset or replace the fuse.
The dishwasher stops
during a programme.
The fuse is defective or
has tripped.
Reset or replace the fuse.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The Wash/Rinse,
Drying and End
There may be a
technical fault.
– Switch the dishwasher off
with the On/Off button s.
indicator lights flash
simultaneously.
Fault code FXX shows
in the display.
After a few seconds:
– Switch the dishwasher back
on.
– Select the programme
required with the
programme selector button.
– Press the Start/Stop button.
If the programme sequence
indicator lights flash again,
there is a technical fault.
– Call the Service
Department.
The drain pump works Fault F70:
– Turn off the stopcock.
even when the door is The Waterproof System
– Call the Service
open.
has reacted.
Department.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
The dishwasher does not fill/drain
Problem
Possible cause
Remedy
The Inlet/Drain
check indicator
flashes.
The stopcock is
closed.
Open the stopcock fully.
The dishwasher
stops during a
programme.
The Inlet/Drain
check indicator
flashes.
Before rectifying the problem
you must:
– Switch the dishwasher off with
the On/Off button s.
Fault F12/F13:
Water inlet restricted.
– Open the stopcock fully.
– Clean the water inlet filter (see
Fault code FXX
shows in the display.
"Problem solving").
– The water pressure at the
intake is lower than 30 kPa
(0.3 bar).
Seek professional advice.
Fault F11:
– Clean the filter combination.
Water outlet is
See "Cleaning and Care".
restricted, water
remains in the wash
cabinet at the end of a
programme.
– Clean the drain pump. See
"Problem solving".
– Clean the non-return valve.
See "Problem solving".
– Remove any kink in the drain
hose.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
General problems
Problem
Possible cause
Remedy
Detergent residue is left The dispenser was still
Make sure the dispenser
in the dispenser at the damp when detergent was is dry before adding
end of a programme.
added.
detergent.
The detergent lid
cannot be closed
properly.
Clogged detergent
residue is blocking the
catch.
Clean the detergent from
the catch.
At the end of a
programme there is a
This is caused by the
drying system and does
The moisture will dissipate
after a short while.
film of moisture on the not indicate a fault.
inside of the door and
the interior walls.
Water remains in the
wash cabinet at the end
of a programme.
Before rectifying the
problem you must:
– Switch the dishwasher
off with the On/Off
button s.
The filter combination in
the wash cabinet is
clogged.
Clean the filter
combination. See
"Cleaning and Care".
The drain pump or
non-return valve may be
blocked.
Clean the drain pump or
the non-return valve. See
"Problem solving".
The drain hose is kinked. Remove any kink from the
drain hose.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Noises
Problem
Possible cause
Remedy
Knocking noise in the A spray arm is knocking
Interrupt the programme,
and rearrange the items
which are obstructing the
spray arm.
wash cabinet.
against an item in a
basket.
Rattling noise in the
wash cabinet.
Items of crockery are
insecure in the wash
cabinet.
Interrupt the programme,
and rearrange the items of
crockery.
Knocking noise in the This may be caused by
This has no influence on
dishwasher function. If in
doubt, contact a suitably
qualified plumber.
water pipes.
the on-site installation or
the cross-section of the
piping.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Unsatisfactory washing result
Problem
Possible cause
Remedy
The dishes are not The dishes were not loaded See notes in "Loading the
clean.
correctly.
dishwasher"
The programme was not
powerful enough.
Select a more intensive
programme. See
"Programme chart".
There is some stubborn
Use the "Adjust sensor wash"
soiling although most of the function (see "Additional
crockery is only lightly soiled functions").
(e.g. with tea stains).
Not enough detergent was
dispensed.
Use more detergent, or
change your detergent.
Items are blocking the path Rearrange the items so that
of the spray arms.
the spray arms can rotate
freely.
The filter combination in the Clean and/or fit the filter
base of the wash cabinet is combination correctly. Clean
not clean or is not correctly the spray arm jets. See
fitted. This may cause the
spray arm jets to get
blocked.
"Cleaning and care".
The non-return valve is open Clean the drain pump and
and blocked. Dirty water has the non-return valve. See
flowed back into the wash
cabinet.
"Cleaning the drain pump
and non-return valve".
Smearing appears The rinse aid dosage is set Reduce the dosage. See
on glassware and too high.
cutlery, there is a
bluish sheen on
"Before using for the first
time".
the surface of
glassware; film can
be wiped off.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
Dishes, cutlery
and glasses are
not dry or are
flecked.
The rinse aid amount may Replenish the reservoir,
be insufficient or the rinse increase the dosage or
aid reservoir empty.
change the brand of rinse aid.
See "Before using for the first
time".
Crockery was taken out of Leave it in for longer. See
the cabinet too soon.
"Operation".
You are using "2 in 1" or
"3 in 1" tablets, which do
not have a strong enough
drying performance.
Set the Tab function (if
present) to "Normal", and
replenish the rinse aid.
The "2 in 1/3 in 1 Tab"
function (if present) is
Set the Tab function (if
present) to the detergent
switched on, even though product being used (see "Tab
tablets are not being used. function").
White residue is
Not enough rinse aid was
Increase the dosage. See
visible on cutlery used.
"Before using for the first time".
and crockery,
There is no salt in the salt
reservoir.
Fill the salt reservoir. See
"Before using for the first time".
clouding occurs
on glassware; film
can be wiped off.
The salt reservoir cap has Replace it, making sure that it
not been screwed on
correctly.
screws back on correctly.
An unsuitable "2 in 1" or
"3 in 1" tablet has been
used.
Change your detergent. Use a
standard liquid, tablet or
powder detergent, and refill
the salt and rinse aid
reservoirs in the dishwasher.
The water softener is
programmed to a setting
which is too low.
Select a higher water softener
setting. See "Before using for
the first time".
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
Glassware has a
brown or blue tinge,
and film cannot be
wiped off.
This may be caused by the Change your detergent.
detergent.
Glassware is dull and The glassware is not
discoloured; film dishwasher-proof. The
cannot be wiped off. surfaces are affected.
There is no remedy.
Purchase glassware which
is dishwasher-proof.
Tea or lipstick stains The wash temperature of
Select a programme with a
higher wash temperature.
have not been
the selected programme
completely removed. was too low.
The bleaching effect of the Change your detergent.
detergent used is too low.
Plastic items are
discoloured.
Natural dyes e.g. from
carrots, tomatoes or
Use more detergent. See
"Operation".
ketchup may be the cause. Discolouration is irrevers
The amount of detergent
used or its bleaching effect
was not sufficient to deal
with natural dyes.
-ible.
There are rust stains The affected items are not There is no remedy.
on cutlery.
corrosion resistant.
Purchase cutlery which is
dishwasher-proof.
The "Quick wash"
programme was not run
after dishwasher salt was
Always run the "Quick
wash" programme, without
any crockery in the
added. Traces of salt have dishwasher, after adding
got into the wash cycle. dishwasher salt.
The salt reservoir cap has Replace it, making sure
not been screwed on
correctly.
that it screws back on
correctly.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving
Cleaning the water inlet filter
A filter is incorporated in the screw
connection of the valve on the water
inlet hose. The filter must be cleaned
when dirty, otherwise insufficient water
flows into the wash cabinet.
,The plastic housing of the water
connection contains an electrical
component. It must not be dipped in
water.
Recommendation
If the mains water contains a large
number of insoluble substances, we
recommend fitting a large-area filter in
the connection between the stopcock
and the water inlet hose threaded
union. This filter is available from the
Miele Spares Parts dept.
^ Carefully remove the seal.
^ Withdraw the filter using pointed
pliers and rinse clean under running
water.
^ Replace the filter and seal, making
sure they are sitting correctly.
^ Reconnect the inlet hose to the
stopcock, making sure it goes on
correctly and is not cross-threaded.
Cleaning the filter:
^ Disconnect the dishwasher from the
mains supply. Switch off at the mains
socket and withdraw the plug.
^ Turn on the stopcock gradually to test
for leaks. If there is a leak, the inlet
hose might not be on securely, or it
may have been screwed on at an
angle. Unscrew and reconnect the
water inlet valve correctly.
^ Turn off the stopcock.
^ Unscrew the inlet hose.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving
Cleaning the drain pump and
non-return valve
If the water has not been pumped away
at the end of a programme the drain
pump or the non-return valve might be
blocked. They are, however, easy to
clean. Watch out for glass or bone
splinters which could cause injury.
^ Disconnect the dishwasher from the
mains supply. Switch off at the mains
socket and withdraw the plug.
^ Take the filter combination out of the
wash cabinet (see "Cleaning and
care", "Cleaning the filters in the wash
cabinet").
The drain pump is situated under the
non-return valve (see arrow).
^ Remove all foreign objects from the
drain pump (watch out for glass or
bone splinters which are particularly
difficult to detect and could cause
injury). Turn the drain pump impeller
by hand to check that there are no
more obstructions. You will feel a little
resistance when you turn the impeller.
^ Scoop the water out of the cabinet
using a suitable container or utensil.
^ Carefully replace the non-return
valve, and secure it with the catch.
,Ensure that the catch engages.
^ Press the catch for the non-return
valve inwards a.
^ Lift out the non-return valve b and
rinse well under running water.
^ Remove all foreign objects from the
non-return valve.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
Repairs
Future updates (PC)
In the event of any faults that you
cannot remedy yourself, please
contact:
The programme update function (PC) is
designed to enable a service
technician to update your appliance’s
electronics in keeping with advances in
technology.
– your Miele dealer, or
– the Miele Service Department
The "PC" indicator light is used as the
interface for this programming.
(see back cover for contact details).
^ When contacting your Dealer or the
Miele Service Department, please
quote the model type and number of
your appliance, both of which are
shown on the data plate on the right
hand side of the door.
For testing institutes
The "Comparison tests" document
gives information regarding loads and
programmes used for comparison
testing.
This document can be ordered by
e-mail from:
Please note that telephone calls may
be monitored and recorded for
training purposes.
– testinfo|miele.de
^ Please give your postal address, as
well as the model type and number of
your dishwasher (see data plate).
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional accessories
To make the most of your dishwasher
Optional accessories for particular purposes are available from your Miele dealer
or from the Spare Parts Department (some may be supplied as standard
depending on model).
If you would like to …
you will need to order …
… wash long-stemmed glassware
… a glassware insert for the upper
basket
... wash a Miele Cappuccinatore
… a Cappuccinatore insert for the
upper basket
... wash bottles,
… a bottle holder
e. g. milk or baby bottles
… wash additional items of cutlery
... wash a lot of glasses
… a small cutlery basket for the lower
basket
… a glassware insert for the bottom
basket
... wash large plates
... an insert for plates up to:
- 33 cm diameter
- 35 cm diameter
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Programme
When to use
Sensor wash
Sensor controlled programme
for normally soiled crockery
Quick wash 40 °C "Quick programme" for lightly soiled crockery, e.g. party crockery;
for flushing out salt residues after replenishing the salt reservoir;
3)
includes sensor controlled glass care;
not suitable for tablet detergents.
3)
Sensor wash
Sensor controlled gentle programme
gentle :
for lightly soiled and temperature sensitive crockery and glassware;
reduce detergent by 50%
1)
Energy save
for normal everyday loads,
energy saving programme which uses a low temperature and long programme
duration;
3)
includes sensor controlled glass care
Pots & pans 75 °C for normally soiled pots, pans, dishes etc with dried on soiling;
for very heavy soiling, add 20% more detergent than recommended
Pre-wash
for rinsing crockery to avoid smells, if a complete cycle is not yet needed
1) Standard programme for energy labelling.
2) See "Operation, Display".
3) Depending on model.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Programme sequence
Consumption
Duration
2)
Energy kWh
Water
h:min
Pre-
wash
Main
wash
Interim
rinse
Final Drying
rinse
Cold
water
connec-
tion
Hot water Litres
connec-
tion
Cold
Hot water
connec-
tion
water
connec-
tion
1
2
1
2
(55 °C)
(55 °C)
(15 °C)
(15 °C)
if
X
if
X
65 °
X
1.0-1.5
0.75
0.65-0.8 13-22 1:39-2:34 1:24-2:08
0.22 13 0:33 0:22
required 45 °- 65 ° required
X
X
X
40 °
50 °
if
X
if
X
55 °
X
X
0.85-1.0
1.05
0.4-0.5 13-22 1:25-1:55 1:14-1:36
required 37 °- 48 ° required
X
X
X
0.7
13
2:56
2:44
45 °
60 °
X
X
X
75 °
X
X
65 °
X
1.6
1.0
17
5
2:46
0:12
2:30
0:12
0.02
0.02
On G 2XXX models (see data plate), the max. energy consumption is 0.1 kWh and the water
consumption is up to 1 litre higher, except on the Pre-wash programme.
The durations given can vary depending on individual circumstances.
Values quoted are in accordance with EN 50242. Results may differ, depending on individual
conditions and the level of soiling.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Electrical connection U.K.
Non-rewireable plugs BS 1363
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
,All electrical work must be
carried out by a suitably qualified
and competent person, in
accordance with current local and
national safety regulations (BS 7671
in the UK).
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
WARNING: THIS APPLIANCE
MUST BE EARTHED
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA (in accordance
with DIN VDE 0664, VDE 0100 Section
739).
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Plumbing
Connection to the water supply
,Water in the dishwasher must
not be used as drinking water.
– The dishwasher may be connected
to a cold or hot water supply, max.
60 °C. We would only recommend
connection to a hot water supply if it
is economical, e.g. a solar powered
supply. When connected to a hot
water supply all programme stages
which would otherwise be carried out
with cold water will be carried out
with hot water.
!The inlet hose must not be
– The inlet hose is approx. 1.5 m long.
A 1.5 metre long flexible metal
shortened or damaged in any way
as it contains electrical components
(see illustration).
extension hose, pressure tested to
14000 kPa/ 140 bar, is available as
an optional accessory if required.
– A stopcock with a 3/4 " male thread
must be provided on site.
– This appliance is constructed to
comply with IEC/EN/DIN 61770 //
VDE 0700 Section 600, and may be
connected to a suitable supply
without an extra non-return valve if
national regulations permit.
– The water pressure (flow pressure at
the take-off point) must be between
30 and 1000 kPa (0.3 and 10 bar).
If the water pressure is too high, a
pressure reducing valve must be
fitted.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Plumbing
Drainage
Venting the drainage system
– The appliance drainage system is
fitted with a non-return valve, which
prevents dirty water from flowing
back into the dishwasher via the
drain hose.
If the on-site drain connection is
situated lower than the guide path for
the bottom basket rollers in the open
door the drainage system must be
vented. Otherwise a siphoning effect
during a programme can cause the
appliance to empty itself of water.
– The dishwasher is supplied with
approx. 1.5 m of flexible drain hose
with an internal diameter of 22 mm.
To vent it:
– The drain hose can be extended
using a connection piece to attach a
further length of hose.
^ Open the dishwasher door fully.
^ Pull the lower spray arm firmly
upwards to remove it.
The drainage length must not be
longer than 4 m, and the delivery
head must not exceed 1 m.
– If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied.
– The hose can be directed to the left
or the right of the appliance.
– The on-site connector for the drain
hose can be adapted to different
widths of hose. If the connector
protrudes too far into the drain hose,
it will need to be shortened.
Otherwise the drain hose may
become blocked.
^ Cut off the top of the vent valve in the
wash cabinet.
– The drain hose must not be
shortened.
– Make sure that there are no kinks in
the hose, and that it is not squashed
or stretched.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Dishwasher model
G 1XXX
G 2XXX
Height freestanding
84.5 cm
-
(adjustable +3.5 cm)
Height built-in
80.5 cm
84.5 cm
(adjustable + 6.5 cm)
(adjustable + 6.5 cm)
Height of building-in
recess
min. 80.5 cm (+ 6.5 cm)
min. 84.5 cm (+ 6.5 cm)
Width
59.8 cm
60 cm
59.8 cm
60 cm
Width of building-in
recess
Depth:
Freestanding
Built-in
60 cm
57 cm
-
57 cm
Weight:
Freestanding
Built-under
Integrated
approx. 61.0 kg
approx. 55.0 kg
approx. 53.0 kg
-
approx. 57.0 kg
approx. 55.0 kg
Voltage
See data plate on right hand side of door.
See plug.
Connected load
Fuse rating
Test certificates awarded KEMA, VDE, radio and
television suppressed
KEMA, VDE, radio and
television suppressed
Water pressure (flow rate) 30 - 1000 kPa
(0.3 - 10 bar)
30 - 1000 kPa
(0.3 - 10 bar)
Hot water connection
Delivery head
Drainage length
Mains cable
up to max. 60 °C
max. 1 m
up to max. 60 °C
max. 1 m
max. 4 m
max. 4 m
approx. 1.7 m
12 place settings
approx. 1.7 m
14 place settings
Capacity
61
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved /
G1220/G1230/G1290/G1291/G2220/G2230/G2290/2291 / 1106
M.-Nr. 06 702 810 / 02
en - GB
Download from Www.Somanuals.com. All Manuals Search And Download.
|