21A3089
FIRST
CLASS
STAMP
HERE
MODEL 620CE
IN CEILING ENCLOSED LOUDSPEAKER
OWNERS MANUAL
4545 E BASELINE RD
PHOENIX AZ 85040-6400
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER BLUEPRINT SERIES PRODUCTS FROM MTX
MTX offers a wide assortment of audio components. Ranging from in-wall
speakers to amplifiers to accessories. Each component is value engi-
neered and must meet strict quality control standards before it becomes
part of the MTX product line.
FEATURES
The Model 620CE in-ceiling enclosed loudspeaker is a
unique design unlike any other before it. It allows you to bring
concert-quality sound to virtually any area of your home that
may have been previously off-limits because of building code
restrictions or weather conditions.
Listed below you will find a sampling of MTX components available from
your authorized Blueprint Series dealer.
IN-WALL LOUDSPEAKERS
MODEL 520W
MODEL 502W
5-1/4” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
11”H x 7-1/2”W x 2-1/2”D
5-1/4” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/84dB Sensitivity
53Hz-20kHz Frequency Response
45 Watts RMS/140 Watts Total
11”H x 7-1/2”W x 2-1/2”D
The Model 620CE utilizes its mounting wings to mount into
a ceiling like conventional in-ceiling speakers, while incorporating
an integral enclosure to provide a vapor barrier between you
and the outside world.
MODEL 620W
6-1/2” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
55 Watts RMS/180 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
MODEL 602W
6-1/2” Two-Way In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/85dB Sensitivity
43Hz-20kHz Frequency Response
50 Watts RMS/160 Watts Total
12-1/16”H x 8-9/16”W x 2-7/8”D
The long excursion, high performance woofer was
designed specifically to work with its integral enclosure to insure
deep, accurate bass. While the soft dome tweeter perfectly com-
plements the woofer with its sweet sound and excellent off-axis
frequency response.
MODEL 820W
8” Two-Way In-Wall Speaker
1” Soft Dome Tweeter
8 Ohm Impedance/86dB Sensitivity
33Hz-20kHz Frequency Response
60 Watts RMS/200 Watts Total
14-1/16”H x 10-1/16”W x 3-1/2”D
MODEL 600WM
6-1/2” Water Resistant Co-Axial In-Wall Speaker
1/2” Polycarbonate Dome Tweeter
8 Ohm Impedance/88dB Sensitivity
64Hz-20kHz Frequency Response
35 Watts RMS/140 Watts Total
8-5/8”H x 8-5/8”W x 2-3/4”D
All of the Model 620CE components have been manufac-
tured with high quality, weather resistant materials. This completes
the Model 620CE’s package of versatility, performance and dura-
bility.
SPEAKER/AMPLIFIER SELECTOR
LPS-600
Accommodates up to 6 pair of speakers
Handles up to 250 Watts/channel continuous (RMS)
Impedance Protection Circuitry
Low profile-full size component
Two-piece, plug in connectors on the rear panel
Accommodates up to 14 gauge wire
TV-5 UL Approved Switches
A/B Amplifier and Input Selector
ACCESSORIES
VC-30B/VC-30W
Decora-Style Volume Control (Bone or White)
10 Step 25 Watts per channel (RMS) 150 Watts Peak
AB-1SB/AB-1SW
Decora-Style A/B Switch (Bone or White)
PCK65C
Pre-Construction Kit for Model 610RCM
PCK85C
Pre-Construction Kit for Model 810RCM
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 1
STEP 4
Using a stud finder (available at low cost at most hardware stores) or
other accurate method, locate center point between two joists and
mark. Using template provided, trace hole pattern on surface of ceiling.
Attach loudspeaker wires to speaker terminals, observing correct polarity,
and position speaker frame up into cutout. Be careful not to pinch wires in
the process.
STEP 5
STEP 2
Carefully tighten the four mounting screws, using a phillips screwdriver. This
will cause the mounting wings to rotate out behind the mounting surface
and secure the speaker in place. Note: the phillips head screws are for tight-
ening the mounting wings. The torx head screws are for the enclosure which
should not be tightened or loosened.
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in ceil-
ing, following traced pattern.
STEP 3
Run loudspeaker wires to sound source location. There are several meth-
ods you can use to accomplish wiring, depending on the construction
characteristics of the room or house. You can add a professional touch
to your installation by using a speaker terminal plate at the source loca-
tion. Leave sufficient amount of wire at speaker location (8 to 10 inches)
to complete connection.
STEP 6
After speaker panel is secured tightly, test for sound. When you are satisfied
the speaker is operational, affix grill. As the grill is designed for a snug fit, you’ll
need to position one edge into the slot first, press or squeeze around perime-
ter of the grill, while pushing leading edge into the grill slot.
Download from Www.Somanuals.com. All Manuals Search And Download.
|