MTX Audio Home Theater System HTB1 User Manual

HTB1  
Home Theater Loudspeaker  
System  
1 Mitek Plaza  
Winslow, IL 61089  
815-367-3000  
800-225-5689  
21A6582  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
HTB1 Satellite/Center Channel  
Driver Compliment  
CENTER  
FRONT  
RIGHT  
FRONT  
LEFT  
FRONT  
Midrange- 3” shielded with paper cone, rubber surround  
Tweeter- 1/2" Balanced dome tweeter  
Frequency Response: 150Hz - 20kHz  
Impedance: 8 ohms nominal  
HTB1  
SUBWOOFER  
45  
Power Handling: 75 watts RMS / 150 watts peak music  
Recommended Amplifier Power: 20-75 watts RMS  
Sensitivity: [email protected]/1M  
LEFT  
REAR  
RIGHT  
REAR  
LISTENING AREA  
Weight:  
Satellite- 1.8 lbs.  
Center Channel- 3.0 lbs  
Dimensions:  
Satellite- 5 7/8"H X 4"W X 4"D  
Center Channel- 4 1/8"H X 9 5/8"W X 3 3/4"D  
Figure 1- Typical loudspeaker placement in a home theater system.  
HTB1 Subwoofer  
Driver Compliment  
Woofer- 8" high excursion woofer  
Amplifier- 60 watts output  
Crossover Frequency: continuously variable 50Hz-150Hz  
Frequency Response: 50Hz - 150Hz  
Enclosure: tuned port design  
Weight: 17 lbs.  
Dimensions: 12 3/4” H X 10 1/4” W X 13” D  
Figure 2- Proper placement of left/center/right front speakers.  
Optional Installation Accessories  
A. Feet for Satellites  
Included in the system are rubber feet that allow you to raise the Satellite  
Speakers up off of a level surface. Simply peel each of the four feet off the  
sheet and press on to the bottom of the Satellite Speaker. Repeat steps for  
the remaining Satellite Speakers.  
B. Feet for Center Channel  
Included in the system are plastic feet that allow the Center Channel to be  
angled more horizontally on top of your television monitor. If you wish to use  
the feet, simply insert the knurled end of the feet into the two holes in the lower  
rear of the Center Channel.  
Figure 3- Improper placement of left/center/right front speakers  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLANATION OF FEATURES AND CONTROLS  
WIRING AND CONNECTIONS  
Turn off all power to your subwoofer and other equipment before making  
any connections.  
Refer to Figure A  
Installation using speaker level inputs (Figure B).  
1) Power Switch: This two position switch controls the power status of the sub-  
woofer.  
Off: Turns the unit off.  
A/V Receiver or Amplifier  
+ -  
+ -  
On: Turns the unit on regardless of whether a signal is present or not.  
2) Subwoofer crossover: This rotary control adjusts a variable low pass filter to  
set the upper frequency at which the output of the subwoofer begins to roll-off.  
Continuously variable from 50Hz to 150 Hz, it matches the upper frequency char-  
acteristics of the subwoofer to the low frequency response of the main stereo  
speakers. Recommended setting: 120Hz-150Hz.  
LEFT  
FRONT  
RIGHT  
FRONT  
FRONT  
CENTER  
SURROUND  
FREQ  
GAIN  
FROM AMPLIFIER  
L
R
POWER  
50Hz 150Hz  
L
R
MIN MAX  
LINE IN  
HI LEVEL IN  
3) Line level input: These RCA phono jacks accept a line level full range signal  
from the preamplifier output of a receiver or preamplifier. This full range signal is  
processed and amplified to power the subwoofer.  
FUSE 1A/250V  
+
-
ON  
1A 250V  
4) Speaker level input: These spring loaded terminals for speaker wire accept a  
stereo, speaker level, full range signal from a receiver or power amplifier. This  
signal is processed and amplified to power the subwoofer.  
CENTER  
FRONT  
OFF  
120 VAC  
100 WATTS  
60 HZ  
HTB1  
Made In China  
5) Fuse: For continued protection replace fuse with same type and size listed.  
6) Level control: This rotary control adjusts the level of the subwoofer and is used  
to balance its volume with that of the main stereo speakers.  
7) Status LED: This light emitting diode shows the status of the subwoofer elec-  
tronics. "Red" indicates that the amplifier is plugged in and the power switch is  
on.  
-
+
-
+
LEFT  
REAR  
RIGHT  
REAR  
FIGURE B  
Installation with A/V amplifiers and receivers that have 5.1 channel line level  
output (Figure C).  
Use an RCA "Y" adaptor to connect both line level inputs.  
OUTPUTS  
A/V Receiver or Amplifier  
 
 
�  
SUB  
FREQ  
GAIN  
FROM AMPLIFIER  
L
 
FRONT  
CENTER  
SURROUND  
 
R
 
�  
POWER  
50Hz 150Hz  
�  
L
R
MIN MAX  
LINE IN  
HI LEVEL IN  
FUSE 1A/250V  
��  
ON  
1A 250V  
+ -  
+ -  
+
-
 
OFF  
 
CENTER  
FRONT  
120 VAC  
100 WATTS  
60 HZ  
RIGHT  
FRONT  
LEFT  
FRONT  
�  
HTB1  
 
����  
 
Made In China  
-
+
-
+
 
 
RIGHT  
REAR  
LEFT  
REAR  
FIGURE C  
 
Download from Www.Somanuals.com. All Manuals Search And Download.  

Mustang Survival Life Jacket MSV971 User Manual
NAD Stereo Amplifier C 320BEE User Manual
National Geographic Weather Radio IN102TOP User Manual
NETGEAR Switch FS516 User Manual
Nikon Network Card SB 16A B User Manual
Nortel Networks Network Router 911x Series User Manual
Nortel Networks Telephone M7310 User Manual
Omega Engineering Thermometer DP251 User Manual
One for All TV Video Accessories SV 9031 User Manual
Oricom Cordless Telephone M5500 Series User Manual