OPERATOR’S MANUAL
Model Numbers
E642E, E662H,
614E, E644E,
E664F
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
Warning:
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
FORM NO. 770-0359A
Download from Www.Somanuals.com. All Manuals Search And Download.
• If the snow thrower should start to vibrate
abnormally, stop the engine and check
immediately for the cause. Vibration is generally a
warning of trouble.
• Never operate the machine at high transport
speeds on slippery surfaces. Look behind and use
care when backing.
• Never direct discharge at bystanders or allow
anyone in front of unit.
• Stop engine whenever you leave the operating
position, before unclogging the collector/impeller
housing or discharge guide, and making any
repairs, adjustments, or inspections. Never place
your hand in the discharge or collector openings.
Use a stick or wooden broom handle to unclog the
discharge opening.
• Disengage power to collector/impeller when
transporting or not in use.
• Use only attachments and accessories approved
by the manufacturer of snow thrower (such as
wheel weights, counter weights, cabs, etc.).
• Never operate the snow thrower without good
visibility or light. Always be sure of your footing
and keep a firm hold on the handles. Walk, never
run.
• Take all possible precautions when leaving the unit
unattended. Disengage the collector/impeller, shift
into neutral, stop the engine, and remove the key.
• When cleaning, repairing, or inspecting, make
certain collector/impeller and all moving parts have
stopped. Disconnect spark plug wire and keep
away from plug to prevent accidental starting.
• Muffler and engine become hot and can cause a
burn. Do not touch.
4. MAINTENANCE AND STORAGE
• Do not run engine indoors, except when starting
engine and transporting snow thrower in or out of
building. Open doors. Exhaust fumes are
dangerous.
• Check shear bolts, engine mounting bolts, etc., at
frequent intervals for proper tightness to be sure
equipment is in safe working condition.
• Never store the machine with fuel in the fuel tank
• Do not clear snow across the face of slopes.
Exercise extreme caution when changing direction
on slopes. Do not attempt to clear steep slopes.
inside
a
building where ignition sources are
present, such as hot water and space heaters,
clothes dryers, and the like. Allow engine to cool
before storing in any enclosure.
• Never operate snow thrower without guards,
plates, or other safety protection devices in place.
• Always refer to operator's manual instructions for
important details if snow thrower is to be stored for
an extended period.
• Never operate snow thrower near glass enclosure,
automobiles, window wells, drop off, etc., without
proper adjustments of snow thrower discharge
angle. Keep children and pets away.
• Run machine a few minutes after throwing snow to
prevent freeze up of collector/impeller.
• Do not overload machine capacity by attempting to
clear snow at too fast a rate.
• Check clutch controls periodically to verify they
engage and disengage properly and readjust if
necessary. Refer to operator's manual for
adjustment instructions.
WARNING - YOUR RESPONSIBILITY: Restrict the use of this power machine to
persons who read, understand and follow the warnings and instructions in this manual and
on the machine.
DANGER
WARNING
1. STOP ENGINE BEFORE REMOVING
DEBRIS AND SERVICING UNIT
2. KEEP CLEAR OF IMPELLER WHILE
ENGINE IS RUNNING
3. NEVER DIRECT DISCHARGE AT
BYSTANDERS OR WINDOWS OR
ALLOW ANYONE IN FRONT OF
UNIT
4. THOROUGHLY INSPECT THE AREA
WHERE THE EQUIPMENT IS TO BE
AVOID INJURY FROM
ROTATING AUGER -
KEEP HANDS, FEET
AND CLOTHING AWAY.
USED AND REMOVE ALL DOOR
MATS, SLEDS, BOARDS, WIRES AND
OTHER FOREIGN OBJECTS
5. REFER TO OWNERS MANUAL FOR
FULL INSTRUCTIONS
3396MW
Figure 1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: FINDING YOUR MODEL NUMBER
This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare
and maintain your snow thrower. Please read and understand what it says.
Before you start to prepare your snow thrower for its first use, please locate the model plate and copy the
information from it in this Operator’s Manual. The information on the model plate is very important if you need
help from your dealer or the MTD customer support department.
• Every snow thrower has a model plate. You can locate it by standing behind the unit in the operating
position and looking down at the rear frame below the engine.
• The model plate will look like Figure 2.
This is where your model number will be.
XXX-X-XXX-X-XXX XXXXXXXXXXX
This is where your serial number will be.
Copy the model number here:
MTD PRODUCTS INC
Copy the serial number here:
CLEVELAND, OHIO 44136
Figure 2
SECTION 3: CALLING CUSTOMER SUPPORT
If you are having difficulty assembling this product or if you have any question regarding the controls,
operation or maintenance of this snow thrower, please call the Customer Support Department. You can
reach them by calling:
1-800-800-7310
Before you call, make sure that you have both your model and serial number ready. By having the model and
serial number ready, you help the Customer Support Representative give you faster service. To find your
units model and serial number, see SECTION 2: FINDING YOUR MODEL NUMBER.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: CONTENTS OF HARDWARE PACK
Lay out the hardware according to the illustration for identification purposes. Parts are illustrated approximately
one-half size. Part numbers are shown in parentheses. (Hardware pack may contain extra items which are not
used on your unit.)
ATTACHING THE HANDLE ASSEMBLY
ATTACHING THE CHUTE ASSEMBLY
A
B
Hex Bolts
1/4-20 x 3/4" Long
(710-3015)
Hex Bolts
5/16-18 x 1-3/4" Long
(710-3180)
Hex Bolts
5/16-18 x 3/4" Long
(710-3008)
Hex Lock Nuts
1/4-20 Thread
(712-3027)
Saddle
(784-5599)
Lock Washers
5/16" I.D.
(736-0119)
Chute Flange
Keepers
(731-0851A)
Carriage Bolts
5/16-18 x 1-1/2" Long
(710-0262)
ATTACHING THE SHIFT ROD
AND CLUTCH CABLES
Hex Nuts
5/16-18 Thread
(712-3010)
D
Hairpin Clips
Ferrule
(714-0104)
(711-0677)
ATTACHING THE CHUTE CRANK
C
Flat Washers
5/16" I.D. x 5/8" O.D.
(736-0264)
Flat Washers
3/8" I.D. x 5/8" O.D.
(736-0185)
Hex Bolt
5/16-18 x 1-1/2"
Long
(710-0442)
Jam Nuts
#10-24 Thread
(712-0121)
Lock Washer
5/16" I.D.
(736-0119)
Hairpin Clip
(714-0104)
Hex Nut
5/16-18 Thread
(712-3010)
“Z”-Fitting (R)
(746-0778)
ATTACHING THE CLUTCH GRIPS
E
AUGER SHEAR BOLTS
F
Hex Screw 5/16-18
x 2.0 (710-0116)
The augers are secured to the spiral shaft with two shear bolts
and hex lock nuts. If you hit a foreign object or ice jam, the snow
thrower is designed so that the bolts will shear. Two replace-
ment shear bolts and nuts are provided for your convenience.
Store in a safe place until needed.
Spacer
.325 I.D. x .50 O.D. x .25
(750-1032)
Shear Bolts
5/16-18 x
1-1/2" Long
(710-0890A)
Hex Lock Nuts
5/16-18 Thread
(712-0429)
Hex Top L-Nut
5/16-18 (712-0429)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ASSEMBLY INSTRUCTIONS
IMPORTANT: After assembly, service engine
with gasoline, and check oil level as instructed in the
separate engine manual packed with your unit.
Attaching the Handle Assembly.
(Hardware A and E)
Lay loose parts out on flat surface.
1. Handle Panel
2. Right Handle
3. Left Handle
5. Traction Drive Control
NOTE: All references to right or left side of the
snow thrower are determined from behind the unit
in the operating position.
Grip
6. Right Grip Bracket
7. Left Grip Bracket
4. Auger Control Grip
UNPACKING
1. Remove staples or break glue on the top flaps of
the carton. Remove any loose parts like
operator’s manual or hardware pack included
with unit.
1
2. Cut along dotted lines and lay end of carton
down flat. Remove packing material.
3. Roll unit out of carton. Check carton thoroughly
for loose parts.
6
7
5
4
4. Extend cables out behind unit and lay them on
the floor.
5. Lay out the contents of the hardware pack
according to the illustration on page 5 and
identify each part.
2
3
6. Find the loose parts in the carton and lay these
on the floor. You should locate the following
loose parts in the carton:
Figure 3
1. Attach left handle and grip bracket to handle
panel with two carriage bolts, lock washers and
hex nuts. (Be sure the bend in the grip bracket is
towards the center of the handle panel. (See
Figure 4.) Do not tighten at this time.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Handle Panel
Right Handle
Left Handle
Auger Control Grip
Traction Drive Control Grip
Right Clutch Grip Bracket
Left Clutch Grip Bracket
Shift Rod (Not Illustrated)
Chute Crank Assembly (Not Illustrated)
Handle Panel
Outer
Edge
of Handle
Panel
Left Grip Bracket
10. Chute Assembly (Not Illustrated)
11. Hardware Pack (Not Illustrated)
Tools Required
Carriage
Bolts
The snow thrower comes partly assembled in the
carton. You will have to complete the assembly.
Follow assembly instructions in this operator’s
manual to make the job safe and easy. You will
need the following tools to assemble the snow
thrower.
Left Handle
(curves in)
Lock Washers
A.
B.
Set of Wrenches (3/8", 9/16", 1/2" or
adjustable)
Pair of pliers
Figure 4
2. Locate auger control grip, part #4 in Figure 3.
The triangular metal tab on the auger control
grip must face the center of the handle panel.
(Hardware D)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Insert curved end of the Z fitting into the top
hole in the triangular metal tab on the auger
control grip. See Figure 5.
5. Secure with hex bolt, spacer and lock nut. See
Figure 6. (Do not overtighten this bolt as it will
prevent the grips from automatically returning to
their upright position.)
6. Repeat process for the right side Traction Drive
Control Grip.
Triangle
Metal Tab
7. Lay handle assembly behind snow thrower. See
Figure 7.
Auger Control
Grip
Hex Bolt
(5/16-18 x 3/4")
& Lock Washer
“Z” Fitting
Figure 5
4. Place the auger control grip on top of the left
handle. The triangular metal tab must be
between the handle and the grip bracket. See
Figure 6.
Figure 7
8. Insert a hex bolt and lock washer through the
lower hole on the bottom of the handle. See
Figure 7.
9. Hold the handle assembly up to the bottom of
the snow thrower frame and thread the hex bolt
into the lower hole in snow thrower frame. Do
not tighten at this time. See Figure 8.
Auger Control Grip
Clutch Grip Bracket
Left
Handle
Hex Lock Nut
(5/16-18)
Figure 8
Spacer
10. Repeat process on the other side.
11. Raise the handle assembly into the upright
position and align the top holes in the handles
with the top holes in the snow thrower frame.
Attach using hex bolts, lock washers and
saddles. (Curve in saddle must match the curve
in the handle.) See Figure 9 and Figure 10.
12. Tighten four carriage bolts and nuts used to
attach the handle panel to the right and left
handles in step 1.
Hex Screw
(5/16-18
x 2.0")
Handle
Panel
“Z” Fitting
13. Tighten all hardware used to attach the handle
assembly to the snow thrower frame.
Figure 6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Traction
Drive
Clutch
Shift
Lever
Ferrule
Flat
Washer
Hairpin
Clip
Shift
Rod
Flat
Washer
Hairpin
Clip
Shift
Arm
Assembly
Figure 9
Figure 11
Flat
Washer
Lock
Washers
Shift
Lever
Hairpin
Clip
Cable
Roller
Guide
Hex Bolt
3/4” Long
Handle
Tab
Ferrule
Shift
Rod
Hex
Bolt 1-3/4”
Long
Flat
Washer
Figure 10
Hairpin
Clip
Shift
Arm
ATTACHING SHIFT ROD
(Hardware D)
Assembly
1. Place the shift lever in the fifth (5) or the fastest
forward speed position.
Figure 12
3. Models 642, 662: Thread the ferrule up or down
the shift rod and align with the lower hole on the
wider side of the shift lever assembly behind the
handle panel. See Figure 11.
2. Models 642, 662: Rotate the shift arm
assembly counter clockwise, as far as it will go.
Insert the shift rod through the shift arm
assembly. When installed the shift arm
assembly should point to the right. Secure with
flat washer and hairpin clip. See Figure 11.
Model 614, 644, 664: Rotate the shift arm
assembly clockwise as far as it will go. Insert
the shift rod through the shift arm assembly.
When installed, the shift arm assembly should
point left. Secure with flat washer and hairpin
clip. See Figure 12.
Model 614, 644, 664: Thread the ferrule onto the
shift rod, up or down the shift rod and align with
the far hole on the narrow side of the shift lever
assembly behind the handle panel. See Figure 12.
4. Secure the ferrule to the shift arm assembly
with flat washer and hairpin clip.
NOTE: Make certain to check for correct
adjustment of the shift rod as instructed in the
FINAL ADJUSTMENTS section before operating
the snow thrower.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING CLUTCH CABLES
1. Thread the hex jam nuts all the way up the
threaded portion of the “Z” ends.
Chute
Assembly
2. Make certain all cables are in the grooves of the
cable roller guides. The roller guides are located
in the lower rear of the unit. Lift the clutch grip in
the raised (up) position.
Hex Bolt
3. Thread the cable onto the threaded portion of
the “Z” end until there is no slack in the cable,
but the cable is NOT tight. Do not overtighten
cable. See Figure 13.
Hex Lock Nut
WARNING: If cable is tightened so
there is tension on the cable with the
clutch grip released, the safety features
of the snow thrower may be overridden.
Chute Flange
Keeper
Figure 14
ATTACHING THE CHUTE CRANK
(Hardware C)
1. Insert hex bolt through the upper chute crank
bracket (located on the chute crank).
See Figure 15.
“Z” End
Lock Washer
Hex Nut
Hex Jam
Nut
Hex Bolt
Cable is
Straight
Upper Chute
Crank Bracket
Figure 13
Figure 15
4. When correct adjustment is reached, tighten the
hex nut against the cable to lock it in position.
2. Place the hex bolt into the hole provided in the
left handle. Secure with lock washer and hex
nut. Do not tighten at this point.
3. Loosen the carriage bolts and hex lock nuts
which secure the lower chute crank bracket to
the extension on the left side of the chute
assembly. See Figure 16.
ATTACHING THE CHUTE ASSEMBLY
(Hardware B)
1. Place chute assembly over chute opening, with
the opening in the chute assembly facing the
front of the unit.
Carriage Bolts
Hex Lock Nuts
2. Place chute flange keepers beneath lip of chute
assembly, flat side down.
3. Insert hex bolt up through chute flange keeper
and chute assembly as shown in Figure 14.
Secure with hex lock nut.
Lower
Chute
Crank
4. After assembling all three chute flange keepers,
tighten all nuts and bolts securely, then back off
1/4 turn to allow easier movement.
Bracket
Figure 16
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Place one flat washer on the end of the chute
crank, then insert the end of the crank into the
hole in the plastic bushing in the chute crank
bracket. See Figure 17.
FINAL ADJUSTMENTS
Auger Drive Clutch
1. To check the adjustment of the auger drive
clutch, push forward on the left hand clutch grip
depressing the rubber bumper under the clutch
grip (See part #13 on page 22). There should be
slack in the cable.
Flat Washer
Chute Crank
2. Release the clutch grip. The cable should be
straight. Make certain you can depress the auger
drive clutch grip against the left handle
completely.
Hairpin Clip
Chute Crank
Bracket
3. If necessary, loosen the hex jam nut and thread
the cable in (for less slack) or out (for more slack)
as necessary. Refer to Figure 13. Recheck the
adjustment. Tighten the jam nut against the cable
when correct adjustment is reached.
Figure 17
5. Place the other flat washer on the end of the chute
crank, and insert hairpin clip into hole in the end of
crank. See Figure 17.
6. Adjust the chute bracket so that the spiral on the
chute crank fully engages the teeth on the chute
assembly.
Traction Drive Clutch and Shift Lever
Adjustment
To check the adjustment of the traction drive clutch
and shift lever:
7. Tighten the nuts on the lower chute crank bracket
securely. Tighten the hex bolt and nut on the upper
chute crank bracket on the handle.
1. Move the shift lever all the way forward to sixth
(6) position. With the traction drive lever released,
push the snow thrower forward. The unit should
roll forward.
LAMP WIRING
Lamp Wire
Alternator
2. Then engage the traction drive clutch grip. The
wheels should stop turning.
Lead
3. Now release the traction drive clutch grip, and
push the unit again. Move the shift lever back to
the fast reverse position, then all the way forward
again. There should be no resistance in the shift
lever, and the wheels should keep turning.
Right Handle
4. If you have resistance when moving the shift
lever or the wheels stop when they should not,
loosen the jam nut on the traction drive cable and
unthread the cable one turn. If the wheels do not
stop when you engage the traction drive clutch
grip, loosen the jam nut on the traction drive
cable and thread the cable in one turn. Recheck
the adjustment and repeat as necessary.
Figure 18
1. Wrap the wire from the lamp down the right
handle until the wire can be plugged into the
alternator lead wire under the fuel tank. See
Figure 18. Be sure lamp wire does not interfere
with the movement of any controls or cables.
5. Tighten the jam nut to secure the cable when
correct adjustment is reached.
IMPORTANT: After attaching the shift rod and
clutch cables, check the adjustments as instructed,
and make any final adjustments necessary before
operating your snow thrower. Failure to follow the
instructions may cause damage to the snow thrower.
NOTE: If you are uncertain that you have reached
the correct adjustment, refer to SECTION 8:
ADJUSTMENTS on page 14.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting The Skid Shoes
The space between the shave plate and the ground
can be adjusted by adjusting the skid shoes.
1. Place skid shoes in the low position to remove
snow close to the ground. Place skid shoes in a
higher position to remove snow from uneven
ground. See Figure 19.
Low Position
High Position
2. Adjust skid shoes by loosening the four hex
nuts and carriage bolts and moving skid shoes
to desired position. Make certain the entire
bottom surface of skid shoe is against the
ground to avoid uneven wear on the skid shoes.
Retighten nuts and bolts securely.
Hex Nuts
Skid
Shoe
Carriage Bolts
Figure 19
WARNING: It is not recommended
that you operate this snow thrower on
gravel as loose gravel can be easily
picked up and thrown by the auger
causing an injury and/or damage to the
snow thrower.
SECTION 6: CONTROLS
THROTTLE CONTROL (See Figure 21)
Thethrottlecontrolislocatedontheengine.Itregulates
thespeedoftheengine.
SHIFT LEVER See Figure 22 for Models 642
and 662. See Figure 23 for Model 614, 644, 664)
The shift lever is located in the center of the handle
panel. The shift lever may be moved into one of six
positions. Run engine with throttle in the fast
position. Use the shift lever to determine ground
speed.
Forward—Five forward speeds: position one (1) is
the slowest; position five (5) is the fastest.
Reverse—One reverse (R) speed.
SAFETY IGNITION SWITCH (See Figure 21)
The ignition key must be inserted in the switch before
the unit will start. Remove the ignition key when
snow thrower is not in use
FUEL SHUT-OFF
VALVE
Closed
NOTE: Model 614, 644, 664 has seven positions.
The fuel shut-off valve,
located under fuel tank,
controls fuel flow from
AUGER DRIVE CLUTCH
(See Figure 22 for Models 642 and 662. See
Figure 23 for Model 614, 644, 664)
The auger drive clutch is located on the left handle.
Squeeze the auger drive clutch against the handle
to engage the augers. Release to stop the snow
throwing action.
Open
tank. (If equipped)
Figure 20
Starter
Handle
TRACTION DRIVE CLUTCH
(See Figure 22 for Models 642 and 662. See
Figure 23 for Model 614, 644, 664)
The traction drive clutch is located on the right
handle. Squeeze the traction drive clutch to engage
the wheel drive. Release to stop.
CHUTE CRANK
(See Figure 22 for Models 642 and 662. See
Figure 23 for Model 614, 644, 664)
The chute crank is located on left hand side of the
snow thrower.
Ignition
Key
Primer
Choke
Throttle
To change the direction in which snow is thrown, turn
chute crank as follows:
Crank clockwise to discharge to the left
Crank counterclockwise to discharge to the right.
Figure 21
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger
Drive
Clutch
Auger
Drive
Clutch
Traction Drive
Clutch
Traction
Drive
Clutch
Shift
Lever
Shift
Lever
Chute
Crank
Chute
Crank
Figure 22
Figure 23
SECTION 7: OPERATION
BEFORE STARTING
WARNING: Observe
Labels on the snow thrower prior to
use. See Figure 1.
all
Warning
Metal Loop
on Spark
Plug Wire
Rubber Boot
Your snow thrower is shipped with oil; however,
you must check the oil level before operating.
Be careful not to overfill.
Figure 24
3. Make certain the auger and drive clutch levers
are in the disengaged (released) position.
The spark plug wire was disconnected for safety.
Attach spark plug wire to spark plug before starting
4. Move throttle control up to FAST position. Insert
ignition key into slot. See Figure 21. Be certain
it snaps into place. Do not turn key.
GAS AND OIL FILL-UP
Check oil level and add oil if necessary. Service the
engine with gasoline as instructed in the separate
engine manual packed with your snow thrower.
Read instructions carefully.
ENGINE WILL NOT START
UNLESS IGNITION KEY IS IN-
SERTED INTO IGNITION
SLOT
IN
CARBURETOR
WARNING: Never
fill
fuel
tank
COVER. DO NOT TURN IGNI-
TION KEY.
indoors, with engine running or while
engine is hot. Do not smoke when
filling fuel tank.
Electric Starter:
TO START ENGINE
WARNING: The electric starter is
NOTE: If unit shows any sign of motion (drive or
augers) with the clutch grips disengaged, shut
engine off immediately. Readjust as instructed in
the Final Adjustments section of SECTION 5:
ASSEMBLY INSTRUCTIONS.
1. Attach spark plug wire to spark plug. Make
certain the metal loop on end of the spark plug
wire (inside the boot) is fastened securely over
the metal tip on the spark plug. See Figure 24.
equipped with a three-wire power cord
and plug, and is designed to operate on
120 volt AC household current. It must
be properly grounded at all times to
avoid the possibility of electric shock
which may be injurious to the operator.
Follow all instructions carefully. If the
house wiring system is not a three-wire
grounded system, do not use this
electric starter under any conditions.
2. Make certain the fuel cutoff valve is in the
OPEN (vertical) position. See Figure 20.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow all instructions carefully. Determine that your
house wiring is a three wire grounded system. Ask a
licensed electrician if you are not certain. If your
house wiring system is not a three-wire grounded
system, do not use this electric starter under any
conditions. If your system is grounded and a three-
hole receptacle is not available at the point your
starter will normally be used, one should be
installed by a licensed electrician.
4. Push primer button two or three times. Refer to
Figure 21 on page 11. If engine is warm, push
primer button once only.
NOTE: Always cover vent hole in primer button
when pushing. Additional priming may be necessary
o
for first start if temperature is below 15 F.
5. Grasp starter handle (refer to Figure 21 on page
11) and pull rope out slowly, until it pulls slightly
harder. Let rope rewind slowly.
When connecting the power cord, always connect
cord to starter on engine first, then plug the other
end into a three-hole grounded receptacle.
6. Pull starter handle rapidly. Do not allow handle
to snap back. Allow it to rewind slowly while
keeping a firm hold on the starter handle.
When disconnecting the power cord, always unplug
the end from the three-hole grounded receptacle
first.
7. Repeat steps 6 and 7 until engine starts. If
engine fails to start, repeat steps 5, 6 and 7 until
engine starts.
1. Make certain the auger drive and traction drive
clutch grips are in the disengaged (released)
position.
TO STOP ENGINE
2. Move throttle control up to FAST position. Insert
ignition key into slot. Refer to Figure 21 on page
11. Be certain it snaps into place. Do not turn
key.
1. Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
2. To help prevent possible freeze-up of starter,
proceed as follows.
3. Rotate choke knob to OFF position.
Electric Starter:
4. Connect power cord to switch box on engine.
Plug the other end of power cord into a three-
hole, grounded 120 volt AC receptacle.
Connect power cord to switch box on engine, then
to 120 volt AC receptacle. With the engine running,
push starter button and spin the starter for several
seconds. The unusual sound made by spinning the
starter will not harm engine or starter. Disconnect
the power cord from receptacle first, and then from
switch box.
5. Push starter button on top of the engine to
crank engine. As you crank the engine, move
choke knob to FULL choke position.
6. When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
Recoil Starter:
With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.
Pulling the starter rope will produce a loud clattering
sound, which is not harmful to the engine or starter.
7. Repeat steps 6 and 7 until engine starts. If
engine fails to start, repeat steps 5, 6, and 7
until engine starts.
8. As engine warms up and begins to operate
evenly, rotate choke knob slowly to OFF
position. If engine falters, return to FULL choke,
then slowly move to OFF position.
3. To stop engine, remove the ignition key. Do not
turn key. Disconnect the spark plug wire from
the spark plug to prevent accidental starting
while equipment is unattended.
Recoil Starter.
NOTE: Do not lose ignition key. Keep it in a safe
place. Engine will not start without the ignition key.
1. Make certain the auger drive and traction drive
clutch grips are in the disengaged (released)
position.
4. Wipe all snow and moisture from the carburetor
cover in the area of the control levers. Also,
move control levers back and forth several
times. Leave throttle control lever in the STOP
or OFF position. Leave choke control in the
FULL choke position.
2. Move throttle control up to FAST position. Insert
ignition key into slot. Refer to Figure 21 on page
11. Be certain it snaps into place. Do not turn
key.
3. Rotate choke knob to FULL choke position (cold
engine start).
If engine is warm, place choke in OFF position
instead of FULL.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TO ENGAGE DRIVE/AUGER
1. With the engine running near top speed, move
shift lever into one of the FORWARD or
WARNING: Temperature of muffler and
surrounding areas may exceed 150 F.
Avoid these areas.
o
REVERSE
positions.
Select
a
speed
appropriate for the snow conditions that exist.
Use the slower speeds until you are familiar
with the operation of the snow thrower.
• For most efficient snow removal, remove
snow immediately after it falls.
2. Squeeze the left hand auger drive clutch to
engage auger.
• Discharge
snow
downwind
whenever
possible. Slightly overlap each previous
swath.
3. While the left hand auger drive clutch is
engaged, engage the right hand traction drive
clutch.
• Set the skid shoes 1/4" below the scraper bar
for normal usage. The skid shoes may be
adjusted upward for hard-packed snow.
Adjust downward when using on gravel or
crushed rock.
NOTE: NEVER move shift lever without first
releasing the drive clutch.
TIRE CHAINS (OPTIONAL):
• Be certain to follow the precautions listed
under ‘‘To Stop Engine’’ in previous column
to prevent possible freeze-up.
Use tire chains when extra traction is necessary.
OPERATING TIPS
• Clean the snow thrower thoroughly after each
use.
NOTE: Allow the engine to warm up for a few
minutes as the engine will not develop full power
until it reaches operating temperature.
SECTION 8: ADJUSTMENTS
WARNING: Never attempt to clean
chute or make any adjustments while
engine is running.
ADJUSTING SKID SHOE
The space between the shave plate and the ground
can be adjusted by adjusting the skid shoe. Slide
the skid shoe upwards and lower the housing to
remove snow close to the ground. Slide skid shoe
downwards and raise the housing to remove snow
from uneven ground like gravel. For more details,
refer to page 11.
ADJUSTING CHUTE
You can control the distance that snow is thrown by
adjusting the angle of the chute assembly. The
sharper the angle, the shorter the distance snow is
thrown.
ADJUSTING TRACTION DRIVE CLUTCH
Refer to the Final Adjustments section on page 10
for instructions to adjust the traction drive clutch. If
you are not sure whether you have been able to
adjust the traction drive clutch properly, check as
follows.
1. To adjust the chute, loosen the hand knob. See
Figure 25.
2. Pivot the top of the chute assembly to the
position desired.
1. Drain the gasoline from the snow thrower or put
a plastic film under the gas cap if the snow
thrower has already been operated. Tip the
snow thrower forward onto the auger housing.
2. Remove the frame cover underneath the snow
thrower by removing the six self-tapping screws.
3. With the traction drive clutch released, check if
there is clearance between the friction wheel
and the drive plate in all positions of the shift
lever. For correct adjustment there has to be
enough clearance.
Hand
Knob
4. With the traction drive clutch engaged, check if
the friction wheel is contacting the drive plate.
See Figure 26. For correct adjustment, these
two must contact.
Figure 25
14
Download from Www.Somanuals.com. All Manuals Search And Download.
5. If adjustment is necessary, loosen the jam nut
on the traction drive cable, and thread cable in
or out as necessary.
Model 614, 644, 664:
3. Push down on the shift arm assembly as far as
it will go. Thread the ferrule up or down the shift
rod and align it with the hole closest to the shift
knob on the narrow side of the shift lever
assembly behind the handle panel.
6. Tighten the jam nut to secure the cable when
correct adjustment is reached. Reassemble the
frame cover with six self-tapping screws.
NOTE: Make certain to check for correct
adjustment of the shift rod as instructed in the Final
Adjustments section before operating the snow
thrower.
Friction
Wheel
CARBURETOR ADJUSTMENT
Gear
Shaft
WARNING: If any adjustments are
made to the engine while the engine is
running (e.g. carburetor), keep clear of
all moving parts. Be careful of heated
surfaces and muffler.
Drive
Plate
Minor carburetor adjustment may be required to
compensate for differences in fuel, temperature,
altitude and load.
Refer to the separate engine manual packed with
your unit for carburetor adjustment information.
Figure 26
DRIVE WHEELS
The wheels may be adjusted for two different
methods of operation. The adjustment is made by
placing the klick pins in one of two different holes on
the right side of the unit. See Figure 28.
Note: If you had earlier placed plastic film under
the gas cap, be sure to remove it once the
adjustment to the traction drive clutch is done and
the snow thrower frame is re-installed.
1. One Wheel Driving—Place klick pin in the
outside axle hole on the right side. This position
gives power drive to the left wheel only, making
the unit easier to maneuver.
Both Wheels Driving—Place klick pin in the hole in
the hub next to the rim on the right side. This
position is good for heavy snow as there is power
drive in both wheels.
ADJUSTING AUGER CLUTCH
To adjust the auger clutch, refer to the Final
Adjustments section on page 10.
ADJUSTING SHIFT ROD
1. Remove the hairpin clip and flat washer from
the ferrule and remove the ferrule from the shift
lever. Place the shift lever in the fifth (5) or the
fastest forward speed position.
Models 642, 662:
Klick Pin in Hole
in Hub Next to Rim
2. Push up on the shift arm assembly as far as it
will go. Thread the ferrule up or down the shift
rod and align with the lower hole on the wider
side of the shift lever assembly behind the
handle panel. Secure the ferrule to the shift arm
assembly again with the hardware earlier
removed.
Outside Hole
in Axle
Figure 27
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9: LUBRICATION
WARNING: Disconnect the spark
GEAR CASE
plug wire and ground against the
The gear case is lubricated with grease at the
factory and does not require checking. If
disassembled for any reason, lubricate with 2
ounces of Shell Alvania grease EPR00, part number
737-0168. Before reassembling, remove old sealant
and apply “Loctite 5699” or equivalent.
engine
before
performing
any
lubrication or maintenance.
ENGINE
Refer to engine manual for all engine lubrication
instructions.
IMPORTANT: Do not overfill the gear case.
Damage to the seals could result. Be sure the vent
plug is free of grease in order to relieve pressure.
WARNING: When following instruct-
ions in separate engine manual for
draining oil, be sure to protect frame to
avoid oil dripping onto transmission
parts.
CHUTE CRANK
SECTION 10: MAINTENANCE
The gear on the end of the chute crank should be
greased with multi-purpose automotive grease once
a season.
AUGERS
The augers are secured to the spiral shaft with two
shear bolts and hex lock nuts. Refer to Figure 28. If
you hit a foreign object or ice jam, the snow thrower
is designed so that the hex bolts will shear.
If the augers will not turn, check to see if the bolts
have sheared. Two replacement shear bolts and
hex lock nuts have been provided with the snow
thrower. For future use, order part number 710-
0890 (shear bolt 5/16-18 x 1.5" long) and 712-0429
(hex insert lock nut 5/16-18 thread).
AUGER SHAFT
At least once a season, remove shear bolts on auger
shaft. Oil or spray lubricant inside shaft. See Figure
28. Also lubricate the auger bearings at least once a
season.
Shear Bolts
SHAVE PLATE AND SKID SHOES
The shave plate and skid shoes on the bottom of
the snow thrower are subject to wear. They should
be checked periodically and replaced when
necessary.
To remove skid shoes, remove the four carriage
bolts, belleville washers and hex nuts which attach
them to the snow thrower. Reassemble new skid
shoes with the four carriage bolts, belleville washers
(cupped side goes against skid shoes) and hex
nuts. Make certain the skid shoes are adjusted to
the same level on both sides.
To remove shave plate, remove the carriage bolts,
belleville washers and hex nuts which attach it to
the snow thrower housing. Reassemble new shave
plate, making sure heads of the carriage bolts
are to the inside of the housing. Tighten securely.
Bearings
Figure 28
SPROCKET SHAFT
Lubricate the sprocket shaft with a light oil at least
once a season or after every 25 hours of operation.
IMPORTANT: Keep all grease and oil off of the
rubber friction wheel and aluminum drive plate.
ENGINE
DRIVE AND SHIFTING MECHANISM
At least once a season or after every 25 hours of
operation, remove the bottom frame cover.
Lubricate any chains, sprockets, gears, bearings,
shafts, and shifting mechanism at least once a
season. Use engine oil or a spray lubricant. Avoid
getting oil on rubber friction wheel and
aluminum drive plate.
Refer to separate engine manual for all engine
maintenance procedures.
BELT REMOVAL AND REPLACEMENT
WARNING: Disconnect the spark
plug wire from the spark plug and
ground.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Roll the front and rear auger belts off the engine
pulley. See Figure 30.
AUGER BELTS
NOTE: It is necessary to remove both belts in
order to change either one. If changing just one belt,
be certain to check the condition of the other belt.
6. Unhook the idler spring from the hex bolt on the
auger housing. See Figure 31.
7. Back out the stop bolt to allow the belts to slip
between the bolt and auger pulley.
See Figure 32.
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping
screws. See Figure 29.
8. Lift the rear auger belt from the auger pulley,
and slip belt between the support bracket and
the auger pulley. See Figure 31. Repeat this
step for front auger belt.
2. Drain the gasoline from the snow thrower, or
place a piece of plastic under the gas cap.
3. Tip the snow thrower up and forward so that it
rests on the auger housing.
9. Replace both auger drive belts by following
instructions in reverse order.
DRIVE BELT
1. Follow steps
instructions.
1
through
4
of previous
2. Pull idler pulley up, and lift belt off engine
pulley, idler pulley, and friction wheel disc.
See Figure 30.
Self-Tapping
Belt
Cover
Screws
3. Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 32.
4. Slip belt between friction wheel and friction
wheel disc. See Figure 31. Remove and replace
belt. Reassemble following the instructions in
reverse order.
NOTE: The support bracket must rest on the stop
bolt after the new belt has been assembled. See
Figure 32.
Figure 29
4. Remove six self-tapping screws from the frame
cover underneath the snow thrower.
Friction
Wheel
Drive
Rear
Belt
Auger
Belt
Engine
Pulley
Front
Auger
Belt
Support
Bracket
Rear
Auger
Belt
Frame
Engine
Pulley
Idler
Pulley
Idler
Pulley
Support
Bracket
Spring
Front
Auger
Pulley
Auger
Pulley
Figure 30
Auger
Housing
Idler
Spring
NOTE: It may be necessary to loosen the six hex
nuts that fasten the frame to the auger housing to
aid in belt removal.
Figure 31
17
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Lightly tap the hex nut to dislodge the ball
bearing from the right side of frame. Remove
the hex nut and bell washer from left end of
shaft.
Friction
Wheel
Disc
Friction Wheel
7. Slide the gear shaft to the right and slide the
friction wheel assembly from the shaft.
Drive Belt
8. Remove the six screws from the friction wheel
assembly (three from each side). Remove the
friction wheel rubber from between the friction
wheel plate.
Support Bracket
9. Reassemble new friction wheel rubber to the
friction wheel assembly, tightening the six
screws in rotation and with equal force.
Stop
Bolt
Position the friction wheel assembly up onto the pin
of the shift rod assembly, and slide the shaft
through the assembly. Reassemble in reverse order.
Figure 32
CHANGINGTHE FRICTIONWHEEL RUBBER
The rubber on the friction wheel is subject to wear
and should be checked after 25 hours of operation,
and periodically thereafter. Replace the friction
wheel rubber if any signs of wear or cracking are
found.
1. Drain the gasoline from the snow thrower, or
place a piece of plastic under the gas cap.
Hex Nut
Bell Washer
2. Tip the snow thrower up and forward, so that it
rests on the auger housing.
3. Remove six self-tapping screws from the frame
cover underneath the snow thrower.
4. Remove the klick pins which secure the wheels,
and remove the wheels from the axle.
5. Using a 7/8" wrench to hold the shaft, loosen,
but do not completely remove, the hex nut and
bell washer on the left end of gear shaft. See
Figure 33.
Figure 33
SECTION 11: OFF-SEASON STORAGE
2. Remove all dirt from exterior of engine and
equipment.
WARNING: Never store engine with
fuel in tank indoors or in poorly
ventilated areas, where fuel fumes may
reach an open flame, spark or pilot
light as on a furnace, water heater,
clothes dryer or other gas appliance.
3. Follow lubrication recommendations on page 16.
NOTE: When storing any type of power
equipment in a poorly ventilated or metal storage
shed, care should be taken to rust proof the
equipment. Using a light oil or silicone, coat the
equipment, especially any chains, springs, bearings
and cables.
1. If unit is to be stored over 30 days, prepare the
engine for storage as instructed in the separate
engine operator’s manual included with your
unit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 12: TROUBLE SHOOTING GUIDE
Trouble
Possible Cause(s)
Corrective Action
Engine fails to start Fuel tank empty, or stale fuel. Fill tank with clean, fresh gasoline. Fuel will not last over thirty
days unless a fuel stabilizer is used.
Blocked fuel line.
Clean fuel line.
Choke not in ON position
Faulty spark plug.
Move switch to ON position
Clean, adjust gap or replace.
Key not in switch on engine. Insert key.
Spark plug wire
Connect spark plug wire.
disconnected.
Primer button not depressed. Refer to the engine manual packed with your unit.
Fuel shut-off valve closed
(if so equipped).
Open fuel shut-off valve.
Improper gasoline and oil
mixture.
Unit running on CHOKE.
Refer to the engine manual packed with your unit.
Move choke lever to OFF position.
Blocked fuel line or stale fuel. Clean fuel line; fill tank with clean fresh gasoline. Fuel will not last
over thirty days unless a fuel stabilizer is used.
Engine runs
erratic**
Water or dirt in fuel system. Drain fuel tank. Refill with fresh fuel.
Carburetor out of adjustment. Refer to the engine manual packed with your unit or have
carburetor adjusted by an authorized service dealer.
Loss of power
Spark plug wire loose.
Gas cap vent hole plugged.
Exhaust port plugged.
Carburetor not adjusted
properly.
Connect and tighten spark plug wire.
Remove ice and snow from cap. Be certain vent hole is clear.
Clean-see Maintenance section of engine manual.
Refer to the engine manual packed with your unit or have
carburetor adjusted by an authorized service dealer.
Stop engine immediately and disconnect spark plug wire.Tighten
all bolts and nuts. Make all necessary repairs. If vibration
continues, have unit serviced by an authorized service dealer.
Engine overheats
Excessive vibration Loose parts or damaged
auger.
Unit fails to propel Incorrect adjustment of drive Adjust drive cable. Refer to Adjustment section of this manual.
itself
cable.
Replace drive belt. Refer to Belt Replacement in Maintenance
Drive belt loose or damaged. section of this manual.
Unit fails to
Discharge chute clogged.
Stop engine immediately and disconnect spark plug wire. Clean
discharge snow
discharge chute and inside of auger housing.
Stop engine immediately and disconnect spark plug wire.
Remove object from auger.
Foreign object lodged in
auger.
Incorrect adjustment of drive Adjust drive cable. Refer to Adjustment section of this manual.
cable. Replace drive belt. Refer to Belt Replacement in Maintenance
Drive belt loose or damaged. section of this manual.
Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 13: ILLUSTRATED PARTS
HOUSING ASSEMBLY
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOUSING ASSEMBLY
REF.
NO.
1
2
3
PART
NO.
784-5618
05931
618-0120
618-0121
618-0160
684-0039A 24" Housing Assembly
684-0040A 26" Housing Assembly
684-0055
684-0065
605-5188
605-5192
605-5248
605-5189
605-5193
605-5249
705-5226
710-0134
REF.
QTY. NO.
PART
NO.
DESCRIPTION
Housing, Bearing
Housing, Bearing
Gear Assembly (24")
Gear Assembly (26")
Gear Assembly (30")
DESCRIPTION
Nut, Lock, Hex, Flanged
Spring Pin
Adapter, Chute
Spring
Lock Washer
Washer,Wave
Wash.Flat,
QTY.
5
2
1
1
9
1
6
16
1
2
1
1
4
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
23 712-0324
24 715-0114
25 731-1379
26 732-0611
27 736-0119
28 736-0174
29 736-0188
30 736-0242
32 738-0281
33 741-0245
34 741-0309
35 741-0475
36 741-0493A Bushing, Flange
37 756-0178
38 784-5580
39 784-5581A 24" Shave Plate
784-5579A 26" Shave Plate
4
30" Housing Assembly
Impeller Assembly
Spiral, 24" R.H.
Spiral, 26" R.H.
Spiral, 30" R.H.
Spiral, 24" L.H.
Spiral, 26" L.H.
Spiral, 30" L.H.
Reinforcement, Chute
Bolt, Carriage
Washer, Bell
5
6
Screw, Shoulder
Bearing, Flange
Bearing, Ball
Bushing, Plastic
7
Idler, Flat
Shoe, Slide
8
9
10 710-0451
11 710-0134
13 710-0451
Screw, Hex
Screw, Carriage
Screw, Carriage
6
3
10
4
1
784-5575
40 784-5632
41 784-5647
42 736-0169
43 712-0798
30" Shave Plate
Arm, Auger Idler
Bracket, Chute Crank
Lock Washer
1
1
1
1
1
5
1
16 710-0890A Bolt, Shear
18 712-0116
20 712-0429
21 712-3010
Hex Lock Nut
Nut, Hex Lock
Nut, Hex
Hex Nut
4
19
44 736-04633 Flat Washer
45 710-04595 Screw. HHCS
GEAR ASSEMBLY
REF.
NO.
1
2
3
PART
NO.
REF.
NO.
10
11
12
13
14
15
16
PART
NO.
DESCRIPTION
Housing—L.H.
Housing—R.H.
Screw
Spiral Axle 24"
Spiral Axle 26"
Spiral Axle 30"
Key
QTY.
DESCRIPTION
QTY.
618-0123
618-0124
710-0642
711-0908
711-0909
711-1024
714-0161
715-0143
717-0526
717-0528
718-0186
1
1
5
1
1
1
1
1
1
1
1
721-0325
721-0327
721-0328
736-0351
736-0369
736-0445
737-0168
741-0662
741-0663
618-0120
618-0121
618-0160
Plug
Seal-Oil
1
1
Locktite 5699
4
Washer-Flat
Washer-Flat
Washer-Flat
2
4
1
5
6
7
8
9
Grease
1.5 oz.
Pin-Spiral
17
18
Bearing-Flange
Bearing-Flange
Ass’y. Complete 24"
Ass’y. Complete 26"
Ass’y. Complete 30"
1
1
1
1
1
Shaft-Worm
Gear-Worm
Collar-Thrust
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE ASSEMBLY
22
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE ASSEMBLY
REF.
NO.
1A 684-0105
1B 684-0106
2
3
4
5
6
7
8
9
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
Control Panel Ass’y - Top Shift †
Control Panel Ass’y.-Front Shift ††
Wire Harness †
Clutch Lever LH
Clutch Lever RH
QTY.
1
1
1
1
1
1
1
2
1
2
1
1
DESCRIPTION
L-Wash. 5/16 ID
Flat Washer .34 ID x .63 OD
Spacer
Handle Tab
Grip
QTY.
9
2
2
2
2
1
1
1
1
1
1
6
29 736-0119
31 736-0264
32 750-1032
33 784-5599
34 720-0274
35 749-0910A Handle RH Black
36 749-0911A Handle LH Black
37 684-0008A Shift Arm Assembly
39 784-5678
40 710-0442
41 684-0022
42 712-3027
44 715-0138
629-0058
705-5233
705-5234
705-5275
705-5274
Clutch Grip Bracket—LH
Clutch Grip Bracket—RH
710-0779A Truss Mach.Tap Scr. #10-.50 †
710-0896
712-0415
Hex B-Tap Scr. 1/4-14 x .625 Lg. †
Self Threading Nut .25 †
Ball Knob
Sealed Beam 18 Watt †
Headlight Bezel †
Chute Crank Brkt.
Hex Bolt 5/16-18 x 1.5
Chute Crank Ass’y.
Hex Flange Nut 1/4-20
Roll Pin .125 Dia. x .62
10 720-0232
11 725-1300
12 731-1317
1
1
13 735-0199A Rubber Bumper
14 747-0921 Shift Rod
15 784-5619A Shift Handle
2
1
1
2
2
4
2
2
1
1
2
4
5
3
1
1
45 720-0201A Knob—Chute Crank
1
1
1
2
1
1
46 726-0100
47 741-0475
48 736-0185
53 746-0897
54 746-0898
55 736-0271
56 710-3015
Cap Speed Nut 3/8" Rod
Plastic Bushing
16 746-0778
17 710-0116
18 710-0262
19 710-3008
20 710-3180
21 711-0677
22 712-0116
23 712-0121
24 712-0429
25 712-3010
26 714-0104
27 732-0193
28 736-0105
“Z” Fitting
Flat Washer .385 ID x .62 OD x .06
Auger Clutch Cable (w/“Z” Fitting)
Drive Clutch Cable (w/“Z” Fitting)
Spring Wash. .317” I.D. x .625” O.D.
Hex Bolt 1/4-20 x .75" Lg. (Gr. 5)
Hex Scr. 5/16-18 x 2.00
Carriage Bolt 5/16-18 x 1.50
Hex Bolt 5/16-18 x .75" Lg.
Hex Screw 5/16-18 x 1.75" Lg.
Adjustment Ferrule
Hex Nut 3/8-24
Hex Nut 10-24
Hex L-Nut 5/16-18
Hex Nut 5/16-18
6
3
1
1
1
1
1
2
1
57 731-0851A Chute Keeper
58 731-1300A Lower Chute
59 731-0921
60 710-0276
61 710-0451
62 720-0284
63 736-0159
64 710-0459
Upper Chute
Carriage Bolt 5/16-18 x 1" Lg.
Carriage Bolt 5/16-18 x .75" Lg.
Knob
Washer - 5/16
Hex Hd. Cap Scr. 3/8-24:1.5”
Int. Cotter Pin 5/16 Dia.
Comp. Spring 38 ID x .88 Lg.
Bell-Wash. .400 ID x .88 OD x .06
† Model 642, 662
†† Model 614, 644, 664
23
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME ASSEMBLY
24
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME ASSEMBLY
REF.
NO.
1
2
3
PART
NO.
618-0063
656-0012A
684-0013B
684-0021
REF.
QTY. NO.
PART
NO.
DESCRIPTION
Bearing Ass’y.
Ass’y., Friction Wheel Disc
Rod Shift, Wheel Drive
Brkt. Ass’y. Friction Wheel
DESCRIPTION
Washer, Bell
QTY.
1
1
1
1
1
25 736-0242
26 712-0324
27 736-0351
28 710-0809
31 738-0869
31 738-0830
32 738-0924
33 741-0563
34 741-0598
35 746-0897
36 746-0898
37 748-0190
38 756-0625
39 784-5590
40 784-5638
41 784-5688
42 784-5687
43 784-5689A
44 710-0599
Nut
1
Flat Washer
Screw
1
1
4
Axle †
1
5
6
7
8
9
684-0030
684-0042B
710-0654A
710-0538
710-0599
Frame Ass’y., 600 S/T
Wheel Friction
Hex Self-Tap Screw
Hex Hd. Cap Screw
Scr., Hex Wash. Hd.
Hex Self-Tap Scr.
Screw, Hex
Nut, Hex
Key
Pin, Klick
Pin, Cotter
Pin, Roll
Gear
Shaft, Hex
Extension Spring
Washer, Bell
Flat Washer
Washer, Flat
1
1
4
2
2
12
1
2
1
2
1
2
1
1
1
2
1
3
Axle††
1
Screw, Shoulder
Bearing, Ball
3
2
Flange Bearing
2
Cable, Auger
1
10 710-0896
11 710-0788
13 712-0711
14 714-0126
15 714-0143
16 714-0474
17 715-0249
19 717-1445
20 717-1444
21 732-0264
22 736-0105
23 736-0160
24 736-0188
Cable, Clutch
1
Spacer
1
Roller, Cable
3
Frame, Shift Bracket
Cover, Frame
1
1
Bracket, Drive Cable Roller
Brkt., Auger Clutch Cable Guide
Brkt., Front Support Guide
Hex Wash Hd. TT-Tap Scr.
1/4-20 x .5" Lg.
Friction Plate
Friction Wheel Hub
Friction Wheel Rubber
1
1
1
6
1
1
1
45 784-5617
46 718-0301A
47 735-0243
† Models 614E, E642E, E644E,
†† Models E662H, E664F
Wheel Assembly
WHEEL ASSEMBLY
WHEEL ASSY. TIRE ONLY (2)
COMPLETE (1)
734-1714
734-1712
SLEEVE
BEARING (5)
741-0401
SIZE
13 x 5
AIR VALVE (3)
734-0255
RIM ONLY (4)
734-1713
734-1711
KLICK PIN (6)
714-0143
734-1527
734-1525
16 x 6.5
735-0255
741-0401
714-0143
25
Download from Www.Somanuals.com. All Manuals Search And Download.
E614E
ENGINE AND “V” BELT
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
05896A
REF.
NO.
PART
NO.
DESCRIPTION
Bracket-Idler
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
DESCRIPTION
Washer-Lock
QTY.
1
16 736-0270
17 736-0331
18 736-0505
19 736-0507
20 748-0234
21 748-0360
22 754-0343
23 754-0430
24 756-0313
25 756-0569
26 756-0967
27 756-0984
28 756-0985
29 390-986
629-0071
710-0627
710-1245
710-0230
710-0342
710-0696
710-0627
710-0896
Cord-Extension 110V †
Screw-Hex
Screw-Hex
Screw-Hex
Screw-Hex
Screw-Hex
Screw-Hex
Screw-Hex
Nut-Hex
Cover-Belt
Spring
Washer-Lock
Washer-Bell
Washer-Flat
Washer-Lock
Washer-Flat
Washer
1
1
1
Spacer
1
Adapter-Pulley
V-Belt
1
1
8
9
V-Belt
1
Idler-Flat
1
10 712-0181
11 731-1324
12 732-0339
13 736-0119
14 736-0242
15 736-0247
Pulley-Half
Pulley
2
1
Pulley-Half
Pulley-Half
Electric Start Kit †
1
1
1
† Optional - Model 614
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Models E642E,E644E,E662H, E664F
ENGINE AND “V” BELT
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
05896A
REF.
NO.
PART
NO.
DESCRIPTION
QTY.
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
DESCRIPTION
Washer—Lock
QTY.
1
Bracket
16 736-0270
17 736-0331
18 736-0505
19 748-0234
20 748-0360
21 754-0346
22 754-0430
23 756-0313
24 756-0569
25 756-0967
26 756-0986
27 756-0987
28 390-987
629-0071
710-0627
710-1245
710-0230
710-0342
710-0696
710-0627
710-0896
Cord, Extension
Screw
Washer—Bell
Washer—Flat
Shoulder Spacer
Pulley, Adapter
V-Belt
1
1
1
1
Screw
Screw
Screw
Screw
Screw
Screw
Nut, Hex
Belt Cover
Spring
1
V-Belt Matched
Idler, Flat
2
1
8
9
Pulley, Half
Pulley—Auger
Pulley Half
Pulley Half
Starter
4
2
1
1
10 712-0181
11 731-1324
12 732-0710
13 736-0119
14 736-0242
15 736-0247
Washer—Flat
Washer—Bell
Washer—Flat
1
29
—
Engine
1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
For TWO YEARS from the date of retail purchase
within the United States of America, its possessions
and territories, MTD PRODUCTS INC will, at its
option, repair or replace, for the original purchaser,
free of charge, any part or parts found to be
defective in material or workmanship. This warranty
covers units which have been operated and
maintained in accordance with the operating
instructions furnished with the unit, and which have
not been subject to misuse, abuse, commercial use,
neglect, accident, improper maintenance or
alteration.
States of America, its possessions and territories,
except those sold through MTD PRODUCTS INC’s
authorized channels of export distribution.
Other Warranties:
1. The engine or component parts thereof carry
separate warranties from their manufacturers.
Please refer to the applicable manufacturer’s
warranty on these items.
2. *Batteries are covered by a 90-day replacement
warranty.
3. Log splitter pumps, valves and cylinders or
component parts thereof are covered by a one
year warranty.
Normal wear parts or components thereof are
subject to separate terms as noted below in the “No
Fault Ninety Day Consumer Warranty” clause.
4. All other warranties, express or implied,
All normal wear part failures will be covered on this
product for a period of 90 days regardless of cause.
After 90 days, but within the two year period, normal
wear parts failures will be covered ONLY IF caused
by defects in material or workmanship of OTHER
component parts. Normal wear parts are defined as
batteries*, belts, blades, blade adapters, grass
bags, rider deck wheels, seats, snow thrower skid
shoes, shave plates and tires.
including
merchantability or fitness for
purpose, are hereby expressly disclaimed in
their entirety.
any
implied
warranty
of
a
particular
5. The provisions as set forth in this warranty
provide the sole and exclusive remedy of MTD
PRODUCTS INC’s obligations arising from the
sales of its products. MTD PRODUCTS INC will
not be liable for incidental or consequential loss
or damage.
How to obtain service: Warranty service is
available, with proof of purchase, through your local
authorized service dealer. To locate the dealer in
your area, please check the yellow pages or contact
the Customer Service Department of MTD
PRODUCTS INC, P. O. Box 368022, Cleveland,
Ohio 44136-9722. Phone 1 (800) 800-7310. The
return of a complete unit will not be accepted by the
factory unless prior written permission has been
extended by the Customer Service Department of
MTD PRODUCTS INC.
How state law relates to this warranty: This
limited warranty gives you specific legal rights, and
you may also have other rights which vary from
state to state. Certain disclaimers are not allowed in
some states and therefore they may not apply to
you under all circumstances.
NOTE: This warranty does not cover routine
maintenance items such as lubricants, filters, blade
sharpening and tune-ups, or adjustments such as
brake adjustments, clutch adjustments or deck
adjustments. Nor does this warranty cover normal
deterioration of the exterior finish due to use or
exposure.
Transportation charges: Transportation charges
for the movement of any power equipment unit or
attachment are the responsibility of the purchaser.
Units exported out of the United States: MTD
PRODUCTS INC does not extend any warranty
for products sold or exported outside of the United
Download from Www.Somanuals.com. All Manuals Search And Download.
|