PS740 Series
Gas
Domestic & Std. Export
ENGLISH
P/N 60250
September 28, 2012
PS740 Series Gas Ovens
Model:
Combinations:
•
•
•
Single Oven
•
PS740G Gas
Double Oven (Two-Stack)
Triple Oven (Three-Stack)
OWNER'S OPERATING AND
INSTALLATION MANUAL
for domestic and standard export ovens
©2012 Middleby Marshall Inc.
is a registered trademark of Middleby Marshall, Inc. All rights reserved.
Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • (847)741-3300 • FAX (847)741-4406
Download from Www.Somanuals.com. All Manuals Search And Download.
Model No.
Modéle No.
Serial No.
Serié No.
Installation Date
Date d'installation
MIDDLEBY MARSHALL
No Quibble limited WarraNty
(U.S.A. Only)
MIDDLEBY MARSHALL INC.
OVEN LIMITED WARRANTY
(Non U.S.A.)
The Seller warrants equipment manufactured by it to be free from
defects in material and workmanship for which it is responsible. The
Seller’sobligationunderthiswarrantyshallbelimitedtoreplacingor
repairing, at Seller’s option, without charge, F.O.B. Seller’s factory,
any part found to be defective and any labor and material expense
incurred by Seller in repairing or replacing such part. Such warranty
is limited to a period of one year from date of original installation or
15 months from date of shipment from Seller’s factory, whichever
is earlier, provided that terms of payment have been fully met. All
labor shall be performed during regular working hours. Overtime
premium will be charged to the Buyer.
MIDDLEBY MARSHALL, HEREINAFTER REFERRED TO
AS “THE SELLER”, WARRANTS EQUIPMENT MANUFAC-
TURED BY IT TO BE FREE FROM DEFECTS IN MATERIAL
AND WORKMANSHIP FOR WHICH IT IS RESPONSIBLE.
THE SELLER’S OBLIGATION UNDER THIS WARRANTY
SHALL BE LIMITED TO REPLACING OR REPAIRING,
AT SELLER’S OPTION, WITHOUT CHARGE, ANY PART
FOUND TO BE DEFECTIVE AND ANY LABOR AND MATE-
RIAL EXPENSE INCURRED BY SELLER IN REPAIRING
OR REPLACING SUCH PART. SUCH WARRANTY SHALL
BE LIMITED TO THE ORIGINAL PURCHASER ONLY
AND SHALL BE EFFECTIVE FOR A PERIOD OF ONE
YEAR FROM DATE OF ORIGINAL INSTALLATION, OR 18
MONTHS FROM DATE OF PURCHASE, WHICHEVER IS
EARLIER, PROVIDED THAT TERMS OF PAYMENT HAVE
BEEN FULLY MET.
This warranty is not valid unless equipment is installed,
started, and demonstrated under the supervision of a factory-
authorized installer.
Normal maintenance functions, including lubrication, adjustment of
airflow,thermostats,doormechanisms,microswitches,burnersand
pilot burners, and replacement of light bulbs, fuses and indicating
lights, are not covered by warranty.
This warranty is valid only if the equipment is installed,
started, and demonstrated under the supervision of a factory-
authorized installer.
Anyrepairsorreplacementsofdefectivepartsshallbeperformedby
Seller’sauthorizedservicepersonnel.Sellershallnotberesponsible
for any costs incurred if the work is performed by other than Seller’s
authorized service personnel.
Normal maintenance functions, including lubrication, clean-
ing, or customer abuse, are not covered by this no quibble
warranty.
When returning any part under warranty, the part must be intact
and complete, without evidence of misuse or abuse, freight prepaid.
Seller shall be responsible only for repairs or replacements of
defective parts performed by Seller’s authorized service per-
sonnel. Authorized service agencies are located in principal
cities throughout the contiguous United States, Alaska, and
Hawaii. This warranty is valid in the 50 United States and
is void elsewhere unless the product is purchased through
Middleby International with warranty included.
Seller shall not be liable for consequential damages of any kind
which occur during the course of installation of equipment, or which
result from the use or misuse by Buyer, its employees or others of
the equipment supplied hereunder, and Buyer’s sole and exclusive
remedy against Seller for any breach of the foregoing warranty or
otherwise shall be for the repair or replacement of the equipment
or parts thereof affected by such breach.
The foregoing warranty is exclusive and in lieu of all
other warranties, expressed or implied. There are no
implied warranties of merchantability or of fitness for a
particular purpose.
The foregoing warranty shall be valid and binding upon Seller if and
only if Buyer loads, operates and maintains the equipment supplied
hereunder in accordance with the instruction manual provided to
Buyer. Seller does not guarantee the process of manufacture by
Buyer or the quality of product to be produced by the equipment
supplied hereunder and Seller shall not be liable for any prospective
or lost profits of Buyer.
The foregoing shall be Seller’s sole and exclusive obliga-
tion and Buyer’s sole and exclusive remedy for any action,
including breach of contract or negligence. In no event shall
Seller be liable for a sum in excess of the purchase price of
the item. Seller shall not be liable for any prospective or lost
profits of Buyer.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF
ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSO-
EVER. SPECIFICALLY THERE ARE NO IMPLIED WARRANTIES
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR
PURPOSE.
This warranty is effective on Middleby Marshall equip-
ment sold on, or after, February 15, 1995.
The foregoing shall be Seller’s sole and exclusive obligation and
Buyer’ssoleandexclusiveremedyforanyaction, whetherinbreach
of contract or negligence. In no event shall seller be liable for a sum
in excess of the purchase price of the item.
© 2012 - Middleby Marshall, A Middleby Company.
The Middleby Marshall logo is a registered trademark of Middleby Marshall, A Middleby Company.
Middleby Marshall Inc. • 1400 Toastmaster Drive • Elgin, Illinois 60120-9272 U.S.A. • (847) 741-3300 • FAX: (847) 741 4406
III
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Page
Page
SECTION 1 – DESCRIPTION ............................................ 1
I. OVEN USES............................................................. 1
II. OVEN COMPONENTS............................................. 1
A. Conveyor Motor Drive ................................... 1
B. Crumb Pans .................................................. 1
C. Conveyor....................................................... 1
D. End Plugs...................................................... 1
E. Eyebrows....................................................... 1
F. Window.......................................................... 1
G. Machinery Compartment Access Panel ........ 1
H. Serial Plate.................................................... 1
I. Control Panel................................................. 1
J. Photo Cell...................................................... 1
K. Gas Burner.................................................... 1
L. Blowers.......................................................... 1
M. .......................................................Air Fingers
1
SECTION 3 – OPERATION ............................................. 20
I. LOCATION AND DESCRIPTION OF CONTROLS 20
II. NORMAL OPERATION, STEP-BY-STEP ................ 21
A. Main Screen ................................................ 21
B. Daily Startup Procedure .............................. 21
C. Daily Shutdown Procedure.......................... 21
III. QUICK REFERENCE: TROUBLESHOOTING....... 22
IV. SCREEN ALERTS.................................................. 22
SECTION 4 – MAINTENANCE ........................................ 23
I. MAINTENANCE – DAILY ....................................... 23
II. MAINTENANCE – MONTHLY................................ 24
III. MAINTENANCE – EVERY 3 MONTHS.................. 25
IV. MAINTENANCE – EVERY 6 MONTHS................. 26
V. KEY SPARE PARTS KIT........................................ 27
III. OVEN SPECIFICATIONS......................................... 2
A. Dimensions.................................................... 2
B. General Specifications .................................. 2
C. Electrical Specifications for
SECTION 5 – ELECTRICAL WIRING DIAGRAM ............ 28
I. WIRING DIAGRAM, 740 GAS OVEN, 208/240V,
50/60 Hz, 1 Ph........................................................ 28
PS740 Gas Ovens......................................... 2
D. Gas Orifice and Pressure Specifications
for PS740 Gas Ovens ................................... 2
SECTION 2 – INSTALLATION .......................................... 3
I. BASE PAD KIT......................................................... 4
II. INSTALLATION KIT.................................................. 6
III. VENTILATION SYSTEM ........................................ 12
A. Requirements.............................................. 12
B. Recommendations ...................................... 12
C. Other Ventilation Concerns ......................... 12
IV. ASSEMBLY ............................................................ 13
A. Base Pad, Legs, Casters............................. 13
B. Stacking ....................................................... 14
C. Restraint Cable Installation ......................... 14
D. Conveyor Installation................................... 15
E. Standoff Installation..................................... 15
V. FINAL ASSEMBLY................................................. 16
VI. ELECTRICAL SUPPLY .......................................... 16
Connection ....................................................... 17
NOTE
VII.
GAS SUPPLY................................................... 17
A. Gas Utility Rough-In Recommendations ..... 17
B. Connection .................................................. 18
C. Gas Conversion........................................... 18
D. Propane Conversion.................................... 18
E. Adjusting the Maximum Pressure Setting ... 18
F. Adjusting the Minimum Pressure Setting .... 19
G. Checkout ..................................................... 19
H. Maintenance................................................ 19
Wiring Diagrams are in Section 5 of this Manual.
The diagram for each oven is also on the lower
inner surface of its Control Console.
P/N 60250 September 28, 2012
IV
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 – DESCRIPTION
Figure 1-1. Oven Components
I. OVEN USES
PS740 Series Ovens can be used to bake and/or cook a wide
variety of food products, such as pizza, pizza –type products,
cookies, sandwiches and others.
II. OVEN COMPONENTS – see Figure 1-1.
A. Conveyor Drive Motor: Moves the conveyor.
B. Crumb Pans: Catch crumbs and other materials that drop
through the conveyor belt. One crumb pan is located at
each end of the conveyor.
C. Conveyor: Moves the food product through the oven.
D. End Plugs: Allow access to the oven’s interior.
E. Eyebrows: Can be adjusted to various heights to prevent
heat loss into the environment.
F. Window: Allows the user to access food products inside
the baking chamber.
G. Machinery Compartment Access Panel: Allows access
to the oven’s interior and control components. No user ser-
viceable parts are located in the machinery compartment.
H. SerialPlate:Providesspecificationsfortheoventhataffect
installation and operation. Refer to Section 2, Installation
for details.
I. Control Panel: Location of the operating controls for the
oven. Refer to Section 3, Operation, for details.
J. Photo Cell: Turns oven On when beam is interrupted.
Not Shown:
K. Gas Burner (gas ovens): Heat air, which is then projected
to the air fingers by the blowers.
L. Blowers:Projecthotairfromtheburnerorheatingelement
to the air fingers.
M. AirFingers:Projectstreamsofhotairontothefoodproduct.
1
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
I. OVEN SPECIFICATIONS
Table 1-1 Dimensions
Overall Height
Single Oven
Double Oven
Triple Ove
48-3/16″ (1219mm)
60″ (1524mm)
62-3/4″ (1575mm)
60″ (1524mm)
78-11/16″ (1981mm)
60″ (1524mm)
Overall Depth
Overall Length
76-1/2″ (1930mm)
76-1/2″ (1930mm)
76-1/2″ (1930mm)
Conveyor Width – belt width is 32″
33-1/2″ (838mm)
or 2 × 15″ (381mm)
33-1/2″ (838mm)
or 2 × 15″ (381mm)
33-1/2″ (838mm)
or 2 × 15″ (381mm)
Shortened Exit Conveyor - 24″
Overall Depth
Single Oven
Double Oven
52.75″ (1340mm)
69″ (1753mm)
Triple Ove
52.75″ (1340mm)
69″ (1753mm)
52.75″ (1340mm)
69″ (1753mm)
Overall Length
* All other dimension are the same
Recommended Minimum Clearances
Rear of Oven to Wall
3″ (76mm)
3″ (76mm)
3″ (76mm)
Control end of conveyor to Wall
Non-control end of conveyor to Wall)
1″ (25.4mm)
1″ (25.4mm)
1″ (25.4mm)
1″ (25.4mm)
1″ (25.4mm)
1″ (25.4mm)
Table 1-2: General Specifications PS740 GAS
32″ Belt
24″ Belt
Weight
1150 lbs. (522kg)
99,000 BTU (25,000kcal, 29 kW/hr)
600°F / 315°C
1150 lbs. (522kg)
Rated Heat Input
Maximum Operation Temperature
Air Blowers
99,000 BTU (25,000kcal, 29 kW/hr)
600°F / 315°C
Two Blowers at 1900 RPM
15 min.
Two Blowers at 1900 RPM
15 min.
Warmup Time
Table 1-3: Electrical specifications for PS740G gas ovens
Main Blower
Voltage
Control Circuit
Voltage
Phase
Freq
Current
Draw
Poles
Wires
208-240VAC
208-240VAC
1Ph
50/60Hz
11-9.6 Amp
2 Pole
3 Wire (2 hot, 1 gd)
Table 1-4: Gas orifice and pressure specifications for PS740G gas ovens
Gas
Main Orifice I.D.
Supply (Inlet)
Orifice (Manifold)
Bypass
Type
PS740G
Pressure
Pressure
Pressure
Natural
0.1065″ (0.120mm)
8-12″ W.C. (19.9 - 29.9mbar)
3.5″ W.C. (8.7mbar)
0.25-0.3″ W.C. (0.6-0.8 mbar)
Propane
0.067″ (1.9mm)
11-14″ W.C. (27.4 - 34.9mbar)
10.0″ W.C. (24.9mbar)
0.9-1.0″ W.C. (2.2-2.5 mbar)
IMPORTANT – Additional electrical information is provided on the oven’s serial plate, and on the wiring diagram inside the
machinery compartment.
GAS ORIFICE AND PRESSURE SPECIFICATIONS (PER OVEN CAVITY) - CE OVENS
Supply (Inlet) Pressure
IT,PT,ES,SE,
Main
Orifice
dia.
UK,CH,IT,AT,
DK,FI
I2H
SE,CH,AT,DK,
FI,DE,NL
I3B/P
BE,IE,IT,PT,
ES,UK
I3+
Orifice
(Manifold)
Pressure
Rated
Heat
Input
Gas
Type
NL
I2L
DE
I2E
BE,FR
I2E+
G20
G25
G30
0.120″
(3.05 mm)
20
mbar
--
20
mbar
20
mbar
--
--
--
--
11.21
mbar
22.36
kW-hr.
0.120″
(3.05 mm)
--
--
25
mbar
--
--
--
--
16.19
mbar
22.36
kW-hr.
0.075″
(1.9 mm)
--
29 or 50
mbar
28-30, 37
or 50 mbar
26.2
mbar
22.59
kW-hr.
NOTE
Wiring Diagrams are contained in Section 5 of this Manual
and are also located inside the oven at the
bottom of the Control Panel.
Additional electrical information is provided on the oven's serial plate.
This Manual Must Be Kept For Future Reference
P/N 60250 September 28, 2012
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 – INSTALLATION
WARNING – After any conversions, readjustments, or service work on the oven:
• Perform a gas leak test.
• Test for proper combustion and gas supply.
• Test for correct air supply, particularly to the • Check that the ventilation system is in operation.
burner blower.
WARNING - Keep the appliance area free and clear of combustibles.
WARNING – The oven must be installed on an even (level) non-flammable flooring and any adjacent walls
must be non-flammable. Recommended minimum clearances are specified in the Description section
of this manual.
WARNING – Do not obstruct the flow of combustion and ventilation air to and from your oven. There
must be no obstructions around or underneath the oven. Constructional changes to the area where the
oven is installed shall not affect the air supply to the oven.
CAUTION: To reduce the risk of fire, the appliance is to be mounted on floors of noncombustible construction
with noncombustible flooring and surface finish and with no combustible material against the underside thereof,
or on noncombustible slabs or arches having no combustible material against the underside thereof, such con-
struction shall in all cases extend not less than 12 inches (304mm) beyond the equipment on all sides.
CAUTION: For additional installation information, contact your local Authorized Service Agent.
NOTE – There must be adequate clearance between the oven and combustible construction. Clearance must
also be provided for servicing and for proper operation.
NOTE – An electrical wiring diagram for the oven is located inside the machinery compartment.
NOTE: All aspects of the oven installation, including placement, utility connections, and ventilation requirements,
must conform with any applicable local, national, or international codes. These codes supersede the require-
ments and guidelines provided in this manual.
NOTE: In the USA, the oven installation must conform to local codes. In the absence of local codes, gas oven
installations must conform with the National Fuel Gas Code, ANSI Z223.1. Gas and electric ovens, when installed,
must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code (NEC), or ANSI/NFPA70.
NOTE: In Canada, the oven installation must conform with local codes. In the absence of local codes, gas
oven installations must conform with the Natural Gas Installation Code, CAN/CGA-B149.1, or the Propane Gas
Installation Code, CAN/CGA-B149.2, as applicable. Gas and electric ovens, when installed, must be electrically
grounded in accordance with local codes, or in the absence of local codes, with the Canadian Electrical Code
CSA C22.2.
NOTE: In Australia, the oven installation must conform with local codes. In the absence of local codes, gas
oven installations must conform with the requirements of AS5601/AG601, Gas, Electricity, and any other relevant
statutory regulations.
3
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
PS740 24″ OVEN INSTALLATION
REQUIRED KITS AND EQUIPMENT
PS740
Gas Oven
Installation
Kit
PS740
Single Oven
Option Base w/
15″ Legs,
Casters & Top
Kit
PS740
DoubleOven
OptionBase w/
6″ Legs,
Casters & Top
Kit
PS740
TripleOven
OptionBase w/
Casters& Top
Kit
TYPE OF INSTALLATION
P/N61452
P/N61123
P/N61457
P/N61458
PS740 Single Gas Oven
PS740 Double Gas Oven
PS740 Triple Gas Oven
1
2
3
1
1
1
PARTS LIST FOR SERIES PS740 GAS OVEN
INSTALLATION KIT
P/N 61452
(Two required for double oven)
(Three required for triple oven)
ITEM
NO.
QTY
PART NO.
22361-0001
61823
DESCRIPTION
1
2
3
4
5
6
1
1
1
1
1
1
FLEXIBLE GAS HOSE
CONVEYOR END STOP
31461
CONVEYOR LEFT REAR STOP
SERVICE AGENCY DIRECTORY
LABEL, MM
42612
22500-0080
51054
ASSY, HANDLE & DOOR
Figure 2-1A. PS740-Series Gas Oven Installation Parts
P/N 60250 September 28, 2012
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PS740 OVEN INSTALLATION
REQUIRED KITS AND EQUIPMENT
PS740
Gas Oven
Installation
Kit
PS740
Single Oven
Option Base w/
15″ Legs,
Casters & Top
Kit
PS740
DoubleOven
OptionBase w/
6″ Legs,
Casters & Top
Kit
PS740
TripleOven
OptionBase w/
Casters& Top
Kit
TYPE OF INSTALLATION
P/N61033
P/N67025
P/N67026
P/N66164
PS740 Single Gas Oven
PS740 Double Gas Oven
PS740 Triple Gas Oven
1
2
3
1
1
1
PARTS LIST FOR SERIES PS740 GAS OVEN
INSTALLATION KIT
P/N 61033
(Two required for double oven)
(Three required for triple oven)
ITEM
NO.
QTY
PART NO.
22361-0001
61823
DESCRIPTION
1
2
3
4
5
6
1
1
1
1
1
1
FLEXIBLE GAS HOSE
CONVEYOR END STOP
55027
CONVEYOR LEFT REAR STOP
SERVICE AGENCY DIRECTORY
LABEL, MM
42612
22500-0080
51054
ASSY, HANDLE & DOOR
Figure 2-1B. PS740-Series Gas Oven Installation Parts
5
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-2A. Model PS740 24″ Single Oven
Option Base with Legs and Top
1
8
HARDWARE BAG
5, 6, 7, 10 & 11
4
2
9
PARTS LIST FOR PS740 SERIES 24″ SINGLE OVEN OPTION - BASE w/15″ LEGS & TOP
P/N 67027
ITEM NO.
QTY
PART NO.
DESCRIPTION
1
1
64943
COMPLETE BASE WELDMENT
2
4
4
4
66851
58930
TOP PLATE, LEG WELDMENT
SWIVEL CASTER FLAT PLATE
3/8″-16 × 1″ HEX SCREW, SST
3/8″ FLAT WASHER, SS
5
32
32
32
1
2000531
21416-0001
21422-0001
22450-0228
61125
6
7
3/8″ SPLIT LOCK WASHER, ZP
RESTRAINT CABLE ASSEMBLY
TOP COVER
8
9
1
10
11
2
59677
SCR, MS SL TR HD 10-32 × 2-1/2″
SCR, MS STR TRSHD 10-32 × 3/4″
2
7A2S15
P/N 60250 September 28, 2012
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-2B. Model PS740 32″ Single Oven
Option Base with Legs and Top
1
8
HARDWARE BAG
5, 6, 7, 10 & 11
4
2
9
PARTS LIST FOR PS740 SERIES 32″ SINGLE OVEN OPTION - BASE w/15″ LEGS & TOP
P/N 67025
ITEM NO.
QTY
PART NO.
DESCRIPTION
1
1
66159
COMPLETE BASE WELDMENT
2
4
4
4
66851
58930
TOP PLATE, LEG WELDMENT
SWIVEL CASTER FLAT PLATE
3/8″-16 × 1″ HEX SCREW, SST
3/8″ FLAT WASHER, SS
5
32
32
32
1
2000531
21416-0001
21422-0001
22450-0228
59560
6
7
3/8″ SPLIT LOCK WASHER, ZP
RESTRAINT CABLE ASSEMBLY
TOP COVER
8
9
1
10
11
2
59677
SCR, MS SL TR HD 10-32 × 2-1/2″
SCR, MS STR TRSHD 10-32 × 3/4″
2
7A2S15
7
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-3A. Model PS740 24″ Double Oven
Option Base with Legs and Top
1
8
HARDWARE BAG
5, 6, 7, 10 & 11
4
2
9
PARTS LIST FOR PS740 SERIES 24″ DOUBLE OVEN OPTION - BASE w/6″ LEGS & TOP
P/N 67028
ITEM NO.
QTY
PART NO.
DESCRIPTION
1
1
64943
COMPLETE BASE WELDMENT
2
4
4
4
66853
58930
TOP PLATE, LEG WELDMENT
SWIVEL CASTER FLAT PLATE
3/8″-16 × 1 HEX SCREW, SST
3/8″ FLAT WASHER, SS
5
32
32
32
1
2000531
21416-0001
21422-0001
22450-0228
61125
6
7
3/8″ SPLIT LOCK WASHER, ZP
RESTRAINT CABLE ASSEMBLY
TOP COVER
8
9
1
10
11
2
59677
SCR, MS SL TR HD 10-32 × 2-1/2″
SCR, MS STR TRSHD 10-32 × 3/4″
2
7A2S15
P/N 60250 September 28, 2012
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-3B. Model PS740 32" Double Oven
Option Base with Legs and Top
1
8
HARDWARE BAG
5, 6, 7, 10 & 11
4
2
9
PARTS LIST FOR PS740 SERIES 32″ DOUBLE OVEN OPTION - BASE w/6″ LEGS & TOP
P/N 67026
ITEM NO.
QTY
PART NO.
DESCRIPTION
1
1
66159
COMPLETE BASE WELDMENT
2
4
4
4
66853
58930
TOP PLATE, LEG WELDMENT
SWIVEL CASTER FLAT PLATE
3/8″-16 × 1 HEX SCREW, SST
3/8″ FLAT WASHER, SS
5
32
32
32
1
2000531
21416-0001
21422-0001
22450-0228
59560
6
7
3/8″ SPLIT LOCK WASHER, ZP
RESTRAINT CABLE ASSEMBLY
TOP COVER
8
9
1
10
11
2
59677
SCR, MS SL TR HD 10-32 × 2-1/2″
SCR, MS STR TRSHD 10-32 × 3/4″
2
7A2S15
9
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-4A. Model PS740 24″ Triple Oven
Option Base with Outriggers and Top
1
15
HARDWARE BAG
7, 8, 9, 10, 11, 12,
13, 14, & 17
5
3
6
2
4
16
PARTS LIST FOR PS740 SERIES 24″ TRIPLE OVEN OPTION - BASE w/CASTERS & TOP
P/N 64946
ITEM NO.
QTY
PART NO.
DESCRIPTION
1
1
64943
COMPLETE BASE WELDMENT
2
3
4
2
45209
22290-0010
22290-0009
45206
QUAD OUTRIGGER WELDMENT
SWIVEL CASTER, FLAT PLATE
SWIVEL CASTER, FLAT PLATE, W/BRAKE
INSERT,QUAD ADJUSTMENT FOOT
SPACER,QUAD CASTER
4
2
5
4
6
4
45205
7
32
32
32
16
8
A27727
3/83 -16x1-1/4 HEX BOLT
8
A21924
3/83 FLAT WASHER, SS
9
21422-0001
21172-0004
2001048
A27750
3/83 SPLIT LOCK WASHER, ZP
3/83 -16 NYLON INSULATED LOCKNUT, ZC
1/23 -13 x 1-3/8 18-8 HEX CAPSCREW
1/23 18-8 FLAT WASHER
10
11
12
13
14
15
16
17
8
8
21422-0016
59677
1/23 18-8 LOCK WASHER
2
SCR, MS SL TR HD 10-32X2-1/2
RESTRAINT CABLE ASSEMBLY
TOP COVER
1
22450-0228
61125
1
2
7A2S15
SCR, MS STR TRSHD 10-32X3/4″
P/N 60250 September 28, 2012
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-4B. Model PS740 32″ Triple Oven
Option Base with Outriggers and Top
1
15
HARDWARE BAG
7, 8, 9, 10, 11, 12,
13, 14, & 17
5
3
6
2
4
16
PARTS LIST FOR PS740 SERIES 32″ TRIPLE OVEN OPTION - BASE w/CASTERS & TOP
P/N 66164
ITEM NO.
QTY
PART NO.
DESCRIPTION
1
1
66159
COMPLETE BASE WELDMENT
2
3
4
2
45209
22290-0010
22290-0009
45206
QUAD OUTRIGGER WELDMENT
SWIVEL CASTER, FLAT PLATE
SWIVEL CASTER, FLAT PLATE, W/BRAKE
INSERT,QUAD ADJUSTMENT FOOT
SPACER,QUAD CASTER
4
2
5
4
6
4
45205
7
32
32
32
16
8
A27727
3/83 -16x1-1/4 HEX BOLT
8
A21924
3/83 FLAT WASHER, SS
9
21422-0001
21172-0004
2001048
A27750
3/83 SPLIT LOCK WASHER, ZP
3/83 -16 NYLON INSULATED LOCKNUT, ZC
1/23 -13 x 1-3/8 18-8 HEX CAPSCREW
1/23 18-8 FLAT WASHER
10
11
12
13
14
15
16
17
8
8
21422-0016
59677
1/23 18-8 LOCK WASHER
2
SCR, MS SL TR HD 10-32X2-1/2
RESTRAINT CABLE ASSEMBLY
TOP COVER
1
22450-0228
59560
1
2
7A2S15
SCR, MS STR TRSHD 10-32X3/4″
11
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Recommendations
III. VENTILATION SYSTEM
NOTE THAT THE HOOD DIMENSIONS SHOWN IN
FIGURE 2-5 ARE RECOMMENDATIONS ONLY.
LOCAL, NATIONAL AND INTERNATIONAL CODES
MUST BE FOLLOWED WHEN INSTALLING THE
VENTILATION SYSTEM. ANY APPLICABLE CODES
SUPERSEDE THE RECOMMENDATIONS SHOWN IN THIS
MANUAL. INAUSTRALIACOMPLIANCETOREGULATIONS
AS5601/AG601 IS MANDATORY.
IMPORTANT
Where national or local codes re-
quire the installation of fire sup-
pression equipment or other
supplementary equipment, DO NOT
mount the
The rate of air flow exhausted through the ventilation system
may vary depending on the oven configuration and hood de-
sign. Consult the hood manufacturer or ventilation engineer
for these specifications.
equipment directly to the oven.
MOUNTING SUCH EQUIPMENT ON
THE OVEN MAY:
To avoid a negative pressure condition in the kitchen area,
return air must be brought back to replenish the air that was
exhausted. A negative pressure in the kitchen can cause
heat- related problems to the oven components as if there
were no ventilation at all. The best method of supplying return
air is through the heating, ventilation and air conditioning
(HVAC) system. Through the HVAC system, the air can be
temperature-controlled for summer and winter. Return air can
also be brought in directly from outside the building, but detri-
mental effects can result from extreme seasonal hot and cold
temperatures from the outdoors.
• VOID AGENCY CERTIFICATIONS
• RESTRICT SERVICE ACCESS
• LEAD TO INCREASED SERVICE
EXPENSES FOR THE OWNER
A. Requirements
NOTE: Return air from the mechanically driven system must
not blow at the opening of the baking chamber. Poor
oven baking performance will result.
CAUTION: GasoveninstallationsREQUIREamechanically
driven ventilation system with electrical exhaust
air sensing control.
C. Other ventilation concerns
A mechanically driven ventilation system is STRONGLY
RECOMMENDED for electric oven installations.
•
Special locations, conditions, or problems may require the
services of a ventilation engineer or specialist.
PROPER VENTILATION OF THE OVEN IS THE RESPON-
SIBILITY OF THE OWNER.
•
•
Inadequate ventilation can inhibit oven performance.
It is recommended that the ventilation system and duct
work be checked at prevailing intervals as specified by the
hood manufacturer and/or HVAC engineer or specialist.
Figure 2-5. Ventilation System
18″ (458mm)
minimum
(Typical - both
ends of oven)
3″ (76mm)
minimum
2″ (51mm)
minimum
8″ (203mm)
minimum
P/N 60250 September 28, 2012
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-6. Leg extension and casters installation
IV. ASSEMBLY
A. Top Panel and Base Pad Assembly
1. Install the four leg extensions onto the base pad using
the 3/8″-16 × 1″ screws, 3/8″ flat washers, and
3/8″ lockwashers supplied in the Base Pad Kit. See
Figure2-6. Checkthatthefinishedsidesofeachlegexten-
sion face OUTWARDS. One rear leg should be attached
using three 3/8″-16 × 1″ screws and the 3/4″ eyebolt, as
shown in Figure 2-6. This eyebolt acts as the anchor point
for the restraint cable assembly (see Part C, Restraint
Cable Installation).
1/2″ flat
washer
1/2″ lock
washer
2. If your oven is equipped with the lower shelf, position it
in place as shown in Figure 2-6. Check that the lip on the
shelf faces DOWN. Seal joint between leg and shelf with
NSF listed silicone.
1/2″-13 × 1-1/4″
hex screw
3. Install one caster onto each leg extension, as shown in
Figure 2-7. Use the 3/8″-16 × 1″ screws, 3/8″ flat wash-
ers, and 3/8″ lockwashers supplied in the Installation Kit.
The locking casters should be installed at the FRONT of
the oven. The non-locking casters should be installed at
the REAR of the oven.
4. Install the lower oven cavity onto the base pad.
See Fig 2-7.
5. For single ovens ONLY:
Install the top panel using the screws included in the base
pad kit, as shown in Figure 2-8. Then, skip ahead to Part
C, Restraint Cable Installation.
For double or triple ovens:
Continue on to Part B, Stacking. Note that the top panel
should NOT be installed for double and triple ovens until
after stacking the oven cavities.
Figure 2-7. Base pad Installation
Figure 2-8. Top panel installation
Bottom oven�
cavity
#10-32 × 2-1/2″
screw length
Top
panel
#10-32 × 3/4″
screw length
Assembled�
base pad
13
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Restraint Cable Installation
NOTE: DO NOT install top panel onto double or triple
ovens until AFTER stacking the oven cavities. See
Part B, Stacking.
Because the oven is equipped with casters, a restraint cable
assembly must be installed to limit the movement of the appli-
ance without depending on the connector and the quick discon-
nect device or its associated piping. One end of the cable is
anchored to the eyebolt on the rear surface of the oven’s base
pad, while the other is anchored to the wall. See Figure 2-11.
B. Stacking
For single ovens, skip ahead to Part C, Restraint Cable
Installation.
After connecting the restraint cable, move the oven to its final
location. Adjust the bottom (hex) sections of the feet so that
the casters are off the floor. For quad ovens, lock the two
front casters.
IMPORTANT
Middleby Marshall STRONGLY RECOMMENDS that PS740
Gas oven cavities be stacked BY AUTHORIZED PERSONEL.
Contact your Middleby Marshall Authorized Service Agent for
complete stacking instructions.
Figure 2-10. Top panel installation
1. Stack an oven cavity on top of the lower oven. Check
the following:
#10-32 × 2-1/2″
screw length
Top
panel
• All four sides of the lower lip (on the bottom edge of
the oven cavity) overlap the top of the lower oven
#10-32 × 3/4″
screw length
• The oven is level
• The oven is firmly seated
See Figure 2-9.
2. For triple ovens, repeat Step 1 to install the top
oven cavity.
3. Install the top panel using the screws included in the base
pad kit, as shown in Figure 2-10.
Figure 2-9. Stacking
Figure 2-11. Installing the Restraint Cable
Restraint cable assembly
3/8″-18 × 1″
eyebolt on
rear leg
extension
3/4″ (19mm)
eyebolt
Wall of structure
P/N 60250 September 28, 2012
14
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Conveyor Installation
Figure 2-13. Conveyor placement
1. Unfold the conveyor as shown in Figure 2-12. Then,
begin to slide the conveyor into the end of the oven. The
conveyor can only be installed from the end of the oven
with the drive motor.
Crumb tray
support
2. Continuemovingtheconveyorintotheovenuntiltheframe
protrudes equally from each end of the oven. Check that
the crumb tray supports located on the underside of the
conveyor frame rest firmly against the lower end plugs,
as shown in Figure 2-13.
bracket
End plug
3. When the conveyor is positioned properly, check for
freedom of movement of the conveyor belt by pulling it
for about 2-3 feet (0.6-1.0m) with your fingers. The drive
and idler shafts must rotate smoothly, and the belt must
move freely without rubbing on the inside of the oven.
4. Check the tension of the conveyor belt as shown in
Figure 2-14. The belt should lift about 1″ (25mm).
DO NOT OVERTIGHTEN THE CONVEYOR BELT.
Conveyor
placed in
oven
NOTE: If necessary, the belt tension can be adjusted by
turning the conveyor adjustment screws, located
at the idler (non-control) end of the conveyor. See
Figure 2-14.
Figure 2-12. Conveyor installation
Folded
frame
Figure 2-14. Conveyor Belt tension
Idler end (with belt tension
adjustment screws)
1″ (25mm) verti-
cal deflection
Adjustment
screws (2) on
idler end of
conveyor
Drive end (with
drive sprocket)
15
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Ifitisnecessarytoaddorremoveconveyorlinkstoachieve
the correct tension, OR if it is necessary to reverse the
conveyor belt for correct orientation, the belt will need to
be removed from the conveyor frame. If this is necessary,
perform the following procedure:
REVERSING THE CONVEYOR BELT
Remove the conveyor from the oven and find the master link
location. Remove master links and remove the belt from the
conveyor frame. Reassemble the belt back onto the frame (in
the reverse direction) and reinstall the master links. Replace
the conveyor assembly in the oven.
• Removetheconveyorassemblyfromtheovenandplace
it flat on the floor.
RESETTING DIRECTION JUMPER
• Remove the master links using long-nose pliers. Then,
roll up the belt along the length of the conveyor frame.
Locate Jumper P1 on the conveyor control board. Move jumper
from terminals 1 and 2, and replace onto terminals 2 and 3.
• Add or remove belt links as necessary to achieve the
correct belt tension.
CAUTION: Shock hazard in compartments electrical filters
• Replace the belt on the conveyor frame. Check that the
conveyorbeltlinksareorientedasshowninFigure2-15,
and that the smooth side of the conveyor belt faces UP.
are electrically alive.
• Connect the inside master links. Check that the links
are oriented as shown in Figure 2-15.
SWITCHING PHOTO DETECTOR
CAUTION: Disconnect Power Before Switching Photo eye.
• Connect the outside master links. Note that the outside
master links each have an open hook on one side. This
hook aligns with the hooks along the sides of the other
conveyor links. See Figure 2-15.
Remove the three screws securing the access door to the unit.
Open the access door and disconnect the connector fitting to
the photo eye assembly. Remove the two screws securing the
photo eye assembly to the control box. Remove the four nuts
securing the photo eye to the housing. Rotate the photo eye
180 degrees and resecure the photo eye with the four nuts.
• Replace the conveyor into the oven.
Figure 2-15. Conveyor and Master Link orientation
Direction
of travel
CORRECT
master link
position
Ontheoppositecontrolbox, removethetwoscrewsholdingthe
cover where the photo eye assembly will be positioned. Secure
the photo eye assembly in position with the two screws. Place
the photo eye cover on the opposite control box, where the
photo eye assembly was removed, and secure the two screws.
Secure the access door with the three screws.
Incorrect
master link
position
Remove the three screws securing the access door on the
opposite side. Open the access door, where the photo eye is
now positioned, and connect the photo eye connector fitting.
Secure the access door with the three screws.
E. Final Assembly
1. Install the crumb trays underneath the conveyor as shown
in Figure 2-16.
Applypowertotheunit.Adjustthephotoeyeheightbyloosening
the two screws securing the photo eye assembly and sliding
the photo eye assembly either up or down, such that the beam
is approximately 1/4 inch above the belt.
Figure 2-16. Crumb Trays
Note: This is MUCH easier in reduced light.
Replace all covers.
VI. ELECTRICAL SUPPLY
WARNING: Authorizedinstallationpersonnelnormallyac-
complish the connections for the ventilation
system, electric supply, and gas supply, as
arranged by the customer. Following these
connections, the factory-authorized installer
can perform the initial startup of the oven.
Crumb tray
insertion
NOTE: Theelectricsupplyinstallationmustsatisfytherequire-
mentsoftheappropriatestatutoryauthoritysuchasthe
National Electrical Code, CSA C22.2; the Australian
Code AG601; or other applicable regulations.
CONVEYOR BELT REVERSAL
Conveyor belt reversal consists of three steps:
1. Physically reversing the conveyor belt.
2. Resetting direction jumper on the conveyor control board.
3. Switching the photo detector.
NOTE: The electric supply connection must meet all national
and local electrical code requirements.
Check the oven serial plate before making any electric supply
connections. Electric supply connections must agree with data
P/N 60250 September 28, 2012
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-17. Utility Connection Locations for Gas Ovens
Strain-relief
fitting
Gas Inlet
(One per Single, Double,
or Triple Oven)
Electrical Junction Box
(One per oven cavity)
ontheovenserialplate.Thelocationoftheserialplateisshown
in Figure 1-1 (in Section 1, Description).
VII. GAS SUPPLY
CAUTION: DURINGPRESSURETESTINGNOTEONEOF
A fused disconnect switch or a main circuit breaker (customer
furnished) MUST be installed in the electric supply line for each
oven cavity. It is recommended that the switch/circuit breaker
have Lockout/Tagout capability.
THE FOLLOWING:
1. The oven and its individual shutoff valve must be discon-
nected from the gas supply piping system during any
pressure testing of that system at test pressure in excess
of ½ psi (3.45 kPa).
The supply conductors must be of the size and material (cop-
per) recommended. Refer to the wiring diagram inside the
machinery compartment of the oven. Electrical specifications
are also listed on the oven’s serial plate and in Table 1-3,
Electrical Specifications (in Section 1, Description).
2. The oven must be isolated from the gas supply piping
system by closing its individual manual shutoff valve dur-
ing any pressure testing of the gas supply piping system
at test pressure equal to or less than ½ psi (3.45 kPa).
The oven requires a ground connection to the oven ground
screw. For gas ovens, the screw is located in the electrical
junction box (see Figure 2-14). If necessary, have the electri-
cian supply the ground wire. Do NOT use the wiring conduit
or other piping for ground connections.
3. If incoming pressure is over 14″ W.C. (35mbar),
aseparateregulatorMUSTbeinstalledinthelineBEFORE
the individual shutoff valve for the oven.
Incoming electrical power lines are fed through the strain-relief
fitting, shown in Figure 2-14. The electrical supply connections
are made inside the electrical junction box. The power lines
then connect to the oven circuits through safety switches
located inside the machinery compartment and each blower
motor compartment. These switches interrupt electrical power
to the oven when the Machinery Compartment Access Panel
is opened, OR when the rear panel is removed.
WARNING: To prevent damage to the control valve regu-
lator during initial turn-on of gas, it is very
important to open the manual shutoff valve
very slowly.
After the initial gas turn-on, the manual
shutoff valve must remain open except
during pressure testing as outlined in the
above steps or when necessary during
service maintenance.
Connection
Refer to the wiring diagram inside the machinery compart-
ment of the oven to determine the correct connections for the
electrical supply lines. Connect the supply as indicated on the
wiring diagram.
A. Gas Utility Rough-In Recommendations
The following gas system specifications are STRONGLY
RECOMMENDED. Deviating from these recommendations
may affect the baking performance of the oven.
CAUTION: The terms of the oven’s warranty require all
start-ups, conversions and service work to be
performed by a Middleby Marshall Authorized
Service Agent.
Gas Meter
• One or two cavities: 750 cfh meter
• Three oven cavities: 1200 cfh meter
Gas Line
• DEDICATED LINE from the gas meter to the oven
• 2″ (50.8mm) pipe for natural gas
• 2″ (50.8mm) pipe for propane
• Maximum length: 2002 (61m). Each 90°elbow
equals 7″ (2.13m) of pipe.
17
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Connection
Figure 2-18. Flexible Gas Hose Installation
Check the oven’s gas supply requirements before making the
gas utility connection. Gas supply requirement are listed on the
oven’s serial plate and in Table 1-4. Gas Orifice and Pressure
Specifications (in Section 1, Description).
1/2″ gas
3/4″-1/2″
gas pipe
reducer
pipe nipple
Check the serial plate to determine the type of gas (Propane
or Natural) to be used with the oven.
To Gas
Supply
Pipe
Refer to the instructions in the gas hose package (included
in the Installation Kit) before connecting the gas line.
One gas line connection method is shown in Figure 2-18;
however, compliancewiththeapplicable standards andregula-
tions is mandatory.
3/4″ gas
pipe nipple
1/2″ gas
line tee with
pressure tap
90°
Elbow
Inlet, regulated, and pilot gas pressure readings can be
taken using a digital tube manometer at the tap location shown
in Figure 2-19. Figure 2-19 shows the burner assembly and
Figure 2-21 shows the gas valve.
Full-Flow
Gas
Shutoff
Valve
NOTE: The installation must conform with local codes or in
the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1-latest edition.
Individual gas
connection
for each oven
cavity
Flexible
Gas Hose
Quick-
disconnect
device
Certain safety code requirements exist for the installation of
gas ovens; refer to the beginning of Section 2 for a list of the
installationstandards.Inaddition,becausetheovenisequipped
with casters, the gas line connection shall be made with a
connector that complies with the Standard for Connectors for
Movable Gas Appliances, ANSI Z21.69 (in U.S.A.), as well
as a quick-disconnect device that complies with the Standard
for Quick-Disconnect Devices for Use With Gas Fuel, ANSI
Z21.41 (in U.S.A.).
Figure 2-19. Gas Burner Assembly
Gas Burner
C. Gas Conversion
Where permitted by local and national codes, it is possible to
convert ovens from natural to propane gas, or from propane
to natural gas. Use the appropriate Middleby Gas Conversion
Kit for the specific oven model.
CAUTION: The terms of the oven’s warranty require all
start-ups, conversions and service work to be
performed by a Middleby Authorized Service
Agent.
D. PS740 Propane Conversion
Two items have to be changed, to change the oven to LP:
Manifold Pressure Tap
1. Replace main orifices.
3. Make sure that the appliance is in operation and the Mo-
2. Adjust main gas regulator per instructions below.
duplus® coil is energized with maximum current.
Disconnect the manifold union closest to the main burner, and
remove the manifold assembly (four screws). Slide out the
manifold assembly (leaving the ignition and sense wires con-
nected). Replace the main orifices.
4. If maximum rate pressure needs adjustment, use an 8
mm wrench to turn adjustment screw for maximum pres-
sure setting (clockwise to increase or counter-clockwise
to decrease pressure), until the desired maximum outlet
pressure is obtained.
ReplacethemainorificesonthemanifoldassemblieswiththeLP
units,andreplacethemanifoldassembly.Reconnecttheunion.
5. Disconnect electrical connection of the Moduplus®.
6. Check minimum pressure setting and readjust if neces-
sary. (See Adjusting Minimum Pressure Setting for proper
adjusting procedure.)
E. Adjusting the Maximum Pressure Setting
1. Disconnect pressure feedback connection (if applicable).
2. Connect a suitable pressure gauge to pipe line or to outlet
pressure tap of gas control concerned, to measure burner
pressure (measuring point must be as near to burner as
possible).
7. Reconnect pressure feedback connection (if applicable).
8. If minimum and maximum pressures are set, wire the
Moduplus® in circuit.
9. Close pressure tap screw.
P/N 60250 September 28, 2012
18
Download from Www.Somanuals.com. All Manuals Search And Download.
F. Adjusting the Minimum Pressure Setting
Figure 2-20. Burner Assembly
1. Disconnect pressure feedback connection (if appcable).
2. Connect a suitable pressure gauge to pipe line or to outlet
pressure tap of gas control concerned, to measure burner
pressure (measuring point must be as near to burner as
possible).
3. Disconnect electrical connection of the Moduplus®.
4. Energize operator, set control in operation and wait until
an outlet pressure is recorded on pressure gauge.
5. If minimum rate pressure needs adjustment, use a 5 mm
wrench to turn adjustment screw for minimum pressure
setting (clockwise to increase or counter-clockwise to
decrease pressure), until the desired minimum outlet
pressure is obtained.
6. Check if main burner lights easily and reliable at minimum
pressure.
7. Reconnect pressure feedback connection (if appcable).
8. Close pressure tap screw.
G. Checkout
After any adjustment, set appliance in operation and observe
through a component cycle to ensure that burner system com-
ponents function correctly.
NOTE: The installer MUST verify oven operation prior to put-
ting oven into service.
H. Maintenance
It is recommended to check yearly the minimum and the maxi-
mum setting and readjust them if necessary.
Figure 2-21. Gas Valve
Adjustment Screw (5 mm)
for minimum pressure
setting
Adjustment Screw
(8 mm) for maxi-
mum
pressure
setting
19
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3 - OPERATION
WARNING
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
C. Temperature Control/Display
D. Message Bar
E. Energy Level
E. Energy Level
Indicators
Indicators
B. Conveyor Time Setting
A. Main On/Off Button
I. LOCATION AND DESCRIPTION OF CONTROLS
A. Main On/Off Button
Displays the average set point of both right and left sides of
theoven. Pressingonthedisplayallowsindividualtemperature
displays and adjustments.
Turns all oven functions on or off. If the oven is below the set
point, it will rise to the set point and turn the conveyor on. If
it is turned off and the oven is above 200° F, the blowers will
remain on until the oven drops below 200° F.
D. Message Bar
Displays messages during oven operation.
E. Energy Level Indicators
B. Conveyor Time Setting
Adjusts and displays the conveyor bake time. Dual belt ovens
have two displays, single units have one.
Displays energy usage on left and right sides of the oven.
C. Temperature Control/Display
P/N 60250 September 28, 2012
20
Download from Www.Somanuals.com. All Manuals Search And Download.
II. NORMAL OPERATION - STEP-BY-STEP-
NOTE: Right to Left temperature settings should not exceed
A. Daily Startup Procedure
a differential of 20 °F.
1. Check that the circuit breaker/fused disconnect is in the
On position. Check that the window is closed. The touch
panel display should be lit.
3. Right Set point temperature - Pressing on this value allows
the user to adjust the set point for the right side of the oven.
4. Left Set point temperature - Pressing on this value allows
2. Adjust the conveyor to the desired bake time.
the user to adjust the set point for the left side of the oven.
3. Press the temperature button to display right and left hand
5. Exit - Returns to the main screen.
oven settings. Set temperatures as desired.
4. Press the ON button to activate the oven. The conveyor
will not run, until the oven temperature has reached the
set points.
C. Energy Modes
Energy Mode One - This mode is automatic, and starts (bake
time +1 minute) after the last product has entered the oven.
In this mode, the main oven blowers will lower to 1500 RPM,
while the oven maintains temperature and belt speed.
B. Daily Shutdown Procedure
1. Make certain there are no products left on the conveyor
in the oven.
Energy Mode Two - The oven lowers its set point by 100°
F, and stops the belt. Anytime that the oven is more than 10
degrees over its set point, the burners will completely shut off,
allowing the oven to cool and the burners are on minimum
flow. The main blowers will continue to run at 1500 RPM in this
mode. Placing any article on the input belt will cause normal
operation of the oven to resume, and bring the set point back
to its original level. The belt will resume operation once both
sides of the oven are within 5° F of the set point.
2. Press the ON square to turn the oven off.
3. Open the window to allow the oven to cool faster.
4. After the oven has cooled and the blowers have turned off,
the circuit breaker/fused disconnect may be turned off.
Quick Reference – Touch Screen Controller
A. Main Screen
1. On/Off button - Used to turn oven On and Off.
2. Conveyorspeed-Pressingoneithertheminutesorseconds
allows a new value to be input for the conveyor speed.
Split belt ovens have two inputs (front and rear belts).
Energy Mode Three - The oven will turn off completely and
shut off the circulation blowers once the oven temperature has
dropped below 200° F. Placing any article on the input belt will
cause normal operation of the oven to resume, and bring the
set point back to its original level. The belt will resume opera-
tion once both sides of the over are within 5° F of the set point.
3. Oven temperature - Pressing on the set temperature shifts
theusertotheoventemperaturesetpoint/indicatorscreen.
4. Energy level indicators - Indicators to either side of the
screen indicate the energy input to that side of the oven.
Energy Mode Four - This is a complete oven shut down. Plac-
ing anything on the belt will NOT return the oven to Operation.
The ON button on the main screen has to be pressed to restart
the oven.
5. Message bar - Indicates various messages pertaining to
current oven conditions.
B. Oven Temperature/Set Point/Indicator Screen
1. Right actual temperature - Indicates current average tem-
perature of the right side of the oven.
2. Left actual temperature - Indicates current average tem-
perature of the left side of the oven.
21
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
III. QUICK REFERENCE: TROUBLESHOOTING
SYMPTOM
PROBLEM
SOLUTION
Oven will not
turn On.
No electrical power
•
Check that the circuit breaker/fused disconnect is on. Make
sure the emergenct stop button is on.
Oven will not
heat.
No gas pressure
•
•
Make sure main gas is on.
Burner did not light
Turn oven off, and restart. If it still does not light, call for
service.
Oven is operating, but little
or no air is coming from
the fingers.
Air fingers may be as-
sembled incorrectly after
cleaning.
•
•
•
Turnovenoff, andallowtocool. Reassemblefingerscorrectly.
Conveyor will not move.
Oven is not up to operating
temperature.
Allow oven to preheat.
Conveyor may be jammed.
Turnovenoff, andallowtocool. Checkconveyorforblockage.
SCREEN ALERTS
SYMPTOM
PROBLEM
SOLUTION
High Control Compartment
Temperature
Clean and replace the front
fan filters.
•
Failure to do this will eventually shut down the oven due to
excessive temperature.
Main Blower problem
or Combustion Blower
problem.
The computer has detected
a problem with either the
main, or burner blowers.
•
This should be corrected by a qualified service technician.
Control Over Temp
Front belt jammed
Front filters are clogged
Front belt has stopped
•
Clean or replace filters.
•
•
Remove obstruction, and restart oven.
If no obstruction, call service.
Rear Belt jammed
High Temp Error
Rear belt has stopped
•
•
Remove obstruction, and restart oven.
If no obstruction, call service.
Thermocouple or
PLC malfunction
•
Call service
Belt off-Oven not
in temperature
Normal operation until
Oven reaches operating
temperature
Energy Saving Mode 1
Energy saving mode 2
Normal operation
Normal Operation
Energy saving Mode 3
Normal operation
P/N 60250 September 28, 2012
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 - MAINTENANCE
WARNING
Before ANY cleaning or servicing of the oven, perform the following procedure:
1. Switch off the oven and allow it to cool. Do NOT service the oven while it is warm.
2. Turn off the electric supply circuit breaker(s) and disconnect the electric supply to the oven.
3. If it is necessary to move a gas oven for cleaning or servicing, disconnect the gas supply before moving the
oven.
When all cleaning and servicing is complete:
4. Reconnect the electrical supply.
5. Turn on the full-flow gas safety valve. Test the gas
line connections for leaks using approved leak test
substances or thick soap suds.
6. Turn on the electric supply circuit breaker(s).
7. Perform the normal startup procedure.
1. If the oven was moved for servicing, return the oven
to its original location.
2. If the restraint cable was disconnected to clean or
service the oven, reconnect it at this time.
3. Reconnect the gas supply.
WARNING
Possibility of injury from moving parts and electrical shock exists in this oven. Switch off and lockout/tagout the
electric supply BEFORE beginning to disassemble, clean, or service any oven. Never disassemble or clean an
oven with the BLOWER ( ) switch or any other circuit of the oven switched on.
CAUTION
NEVER use a water hose or pressurized steam-cleaning equipment when cleaning this oven. To avoid saturating the oven
insulation, DO NOT use excessive amounts of water. DO NOT use a caustic oven cleaner, which can damage the bake
chamber surfaces.
NOTE
ANY replacement parts that require access to the interior of the oven may ONLY be replaced by a Middleby Marshall Autho-
rized Service Agent. It is also strongly recommended that the 3-Month Maintenance and 6-Month Maintenance procedures
in this section be performed ONLY by a Middleby Marshall Authorized Service Agent.
I. MAINTENANCE - DAILY
Figure 4-1. Cooling Vents and Grills
A. Check that the oven is cool and the power is disconnected,
asdescribedinthewarningatthebeginningofthisSection.
B. Clean ALL of the cooling fan grills and vent openings with
a stiff nylon brush. Refer to Figure 4-1 for the locations of
the grills and vents.
C. Clean the outside of the oven with a soft cloth and mild
detergent.
D. Check that ALL cooling fans are operating properly.
CAUTION: If a cooling fan is not operating correctly, it must
bereplacedIMMEDIATELY. Operatingtheoven
without adequate cooling can seriously damage
the oven's internal components.
Vents on
front panel
of oven
E. Clean the conveyor belts with a stiff nylon brush. This
is more easily accomplished by allowing the conveyor to
run while you stand at the exit end of the conveyor. Then,
brush the crumbs off the conveyor as it moves.
F. Remove and clean the crumb trays. If necessary, refer to
Figure 2-16 (in Section 2, Installation) when replacing the
crumb trays into the oven.
G. Clean the window in place.
Fan grills (2) on rear
of oven and control
compartment
Vent (1) on rear
of machinery
compartment
23
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-2. Removing Air Fingers and Plates
II. MAINTENANCE – MONTHLY
NOTE: When removing the conveyor, refer to Figure 2-12 (in
Section 2, Installation).
A. Check that the oven is cool and the power is disconnected,
as described in the warning at the beginning of this Sec-
tion.
B. Remove the crumb trays from the oven.
C. Lift the drive end of the conveyor slightly, and push it
forward into the oven. This removes the tension from the
drivechain.Then,removethedrivechainfromtheconveyor
sprocket.
D. Slidetheconveyoroutoftheoven,foldingitasitisremoved.
E. Remove the end plugs from the oven. The end plugs are
shown in Figure 1-1 (in Section 1, Description).
F. Slide the air fingers and blank plates out of the oven, as
shown in Figure 4-2. AS EACH FINGER OR PLATE IS
REMOVED, WRITE A “LOCATION CODE” ON IT WITH A
MARKER to make sure that it can be reinstalled correctly.
Example of markings:
Figure 4-3. Disassembling the Air Fingers
(Top Row)
T1
T2 T3
T4
T5 T6
(Bottom Row) B1 B2 B3
B4 B5 B6
G. Disassemble the air fingers as shown in Figure 4-3. AS
EACHFINGERISDISASSEMBLED, WRITETHE“LOCA-
TION CODE” FOR THE FINGER ON ALL THREE OF ITS
PIECES. This will help you in correctly reassembling the
air fingers.
CAUTION: Incorrectreassemblyoftheairfingerswillchange
the baking properties of the oven.
H. Cleantheairfingercomponentsandtheinteriorofthebaking
chamber using a vacuum cleaner and a damp cloth. Refer
to the boxed warnings at the beginning of this Section for
cleaning precautions.
I. Reassemble the air fingers. Then, replace them in the
oven, using the “location guide” as a guide.
J. Replace the end plugs on the oven.
K. Reassembletheconveyorintotheoven. Ifthedrivesprocket
was removed when installing the conveyor, replace it at
this time.
L. Reattach the drive chain.
M. Check the tension of the conveyor belt as shown in Fig-
ure 2-14 (in Section 2, Installation). The belt should lift
between 3 - 4″ (75-100mm). DO NOT OVERTIGHTEN
THECONVEYORBELT. Ifnecessary, thebelttensioncan
be adjusted by turning the conveyor adjustment screws,
located at the idler (right) end of the conveyor.
N. Replace the crumb trays.
P/N 60250 September 28, 2012
24
Download from Www.Somanuals.com. All Manuals Search And Download.
two sections of the shaft. See Figure 4-4.
III. MAINTENANCE – EVERY 3 MONTHS
9. Replacetheconveyoradjustmentscrewsasshownin
Figure4-4. Toallowtheconveyorbelttobereinstalled
later, do not tighten the screws at this time.
A. Check that the oven is cool and the power is disconnected,
asdescribedinthewarningatthebeginningofthisSection.
B. Vacuum both of the blower mounts, and their surrounding
10. Loosen the set screw on both of the conveyor drive
sprockets.Then,removethesprocketsfromtheshaft.
compartments, using a shop vacuum.
C. Tighten all electrical terminal screws.
11. Check the conveyor configuration as follows:
D. Split Belt Disassembly and Cleaning
High-speed conveyors are equipped with large flange
bearings at both ends of the shaft, as shown in
Figure 4-5. For these conveyors, remove the two
screws that hold each bearing to the conveyor frame.
With the screws removed, lift the end of the shaft at
the front of the oven, and pull the entire assembly free
of the conveyor frame.
1. Refer to Part D, Conveyor Installation, in the Installa-
tionsectionofthisManual.Then,removethefollowing
components from the oven:
• Conveyor end stop
• Crumb trays
Standard conveyors are equipped with bronze bush-
ings mounted on spacers at both ends of the shaft,
as shown in Figure 4-5. For these conveyors, remove
the two screws that hold the bracket to the conveyor
frame. With the screws removed, lift the end of the
shaft at the front of the oven, and pull the entire as-
sembly free of the conveyor frame. The brackets will
be removed along with the drive shaft assembly.
• Chain cover
• Drive chains
• End plugs
• Conveyor assembly
2. Remove the master links from each conveyor belt.
Then, rollthebeltsupalongthelengthoftheconveyor
to remove them from the frame.
12. Disassemble and lubricate the two sections of the
3. Removethetwoconveyoradjustmentscrewsfromthe
idler end of the conveyor frame, as shown in Figure
4-4.
drive shaft as described for the idler shaft, above.
13. Before reassembling the shafts into the conveyor
frame, check that they are oriented properly.
4. Remove the idler shaft assembly from the conveyor.
5. Pull apart the two sections of the idler shaft.
14. Reassemble the drive shaft into the conveyor. Make
sure that the bronze washer is in place between the
two sections of the shaft. See Figure 4-4.
6. Clean the shafts thoroughly using a rag. Then, lubri-
cate both the extended shaft and the interior of the
hollowshaftusingalightfood-gradelubricant.DONOT
lubricate the shafts using WD40 or a similar product.
This can cause the shafts to wear rapidly.
15. Replace the drive sprockets. Reassemble the belts
and master links onto the conveyor.
16. Reinstall the end plugs and conveyor onto the oven.
17. Reattach the drive chains. Replace the chain cover.
7. Before reassembling the shafts into the conveyor
18. Check the tension of the conveyor belt as shown in
Figure2-14(inSection2,Installation).Thebeltshould
lift about 1″ (25mm). If necessary, adjust the belt ten-
sion by turning the conveyor adjustment screws.
frame, check that they are oriented properly.
8. Reassemble the idler shaft into the conveyor. Make
sure that the bronze washer is in place between the
19. Replace all components onto the oven.
Figure 4-4. Disassembling the idler shaft
Figure 4-5. Drive shaft configurations
25
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-7. Rear panel access
Figure 4-6. Disassembling the drive shaft
Remove eight (8)
screws to remove
rear panel
Bearings
(2 total)
Blower belt
Blower motor
Loosen four (4) screws to adjust mo-
tor position and belt tension
E. Blower Belt
IV. MAINTENANCE - EVERY 6 MONTHS
1. RemovethesixscrewsshowninFigure4-7.Then,remove
A. Check that the oven is cool and the power is disconnected,
asdescribedinthewarningatthebeginningofthisSection.
the rear panel from the oven.
2. Check the blower belt for the proper 1/4″ (6mm) deflection
B. Check for excessive wear on the conveyor drive motor
brushes. The brushes should be replaced if they have
worn to less than 1/4" (6mm) in length. Be sure to replace
the brushes in exactly the same position.
at the center, and for cracking or excessive wear.
See Figure 4-7. Overtightening the belt will cause premature
bearing failure and possible vibrations. A loose belt may also
cause vibrations.
C. For gas ovens, inspect and clean the burner nozzle and
the spark electrode assembly.
3. If necessary, adjust the tension of the belt by loosening
the four motor mounting bolts. Reposition the motor as
neccessary until the correct 1/4″ (6mm) deflection is
reached, then tighten the bolts.
D. Check the conveyor drive shaft bushings and spacers.
Replace the components if they are worn.
P/N 60250 September 28, 2012
26
Download from Www.Somanuals.com. All Manuals Search And Download.
V. KEY SPARE PARTS – Available separately. See Figure 4-8.
1
2
3
4
5
10
16, 17, 18
24
22
23
19
20
21
Figure 4-8. Key Spare Parts
KEY SPARE PARTS PS740 GAS
ITEM QTY.
P/N
DESCRIPTION
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
60190
58920
58679
60194
M9608
60196
97525
51399
62044
57288
61602
60679
60671
33983
32108
60684
58668
58669
60250
59132
59668
62288
50240
64106
Digital Display, Programmed
Motor, Conveyor Drive
Conveyor Control Board
Inverter, Programmed
Power Supply
3
4
5
6
Kit, Thermocouple
Fan Cooling Control
Fan Cooling Rear
7
8
9
Air Switch
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Motor, Blower
Ignition Module
Assy, Valve Gas Modulating
Board, Signal Cond. 0-15VDC
High Limit Control Module,240V
Transformer,240Vp:24Vs
Control,C14RS Programmed
Thermocouple Module
Current Module
PhotoCell
Relay, DPDT 24V Coil
Belt, Blower
Ignitor, Single Rod
Ignition Cable, 25″
Bearing, PB 5/8 B
27
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 - WIRING DIAGRAM
P/N 60250 September 28, 2012
28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
29
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
P/N 60250 September 28, 2012
30
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
31
P/N 60250 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Improper installation, adjustment, alteration, service or maintenance
can cause property damage, injury or death. Read the installation, op-
erating and maintenance instructions thoroughly before
installing or servicing this equipment.
NOTICE
During the warranty period, ALL parts replacement and servicing should be performed
by your Middleby Marshall Authorized Service Agent. Service that is performed by par-
ties other than your Middleby Marshall Authorized Service Agent may void your war-
ranty.
NOTICE
Using any parts other than genuine Middleby Marshall factory manufactured parts re-
lieves the manufacturer of all warranty and liability.
NOTICE
Middleby Marshall reserves the right to change specifications at any time.
Middleby is proud to support the Commercial Food Equipment
Service Association (CFESA). We recognize and applaud
CFESA's ongoing efforts to improve the quality of technical
service in the industry.
Middleby Cooking Systems Group • 1400 Toastmaster Drive • Elgin, IL 60120 • USA • (847)741-3300 • FAX (847)741-4406
050 September 28, 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|