INSTALLATION INSTRUCTIONS FOR PART 95-2004
APPLICATIONS
Cadillac
1997-2001 Catera
1996-1999 Deville (Column Shift Only)
95-2004
KIT FEATURES
• DDIN Head Unit Provision
• ISO Stacked Head Unit Provision
KIT COMPONENTS
• ( A) DDIN Brackets • ( B) DDIN Trim Plate • ( C) (4) Speed Clips • ( 4) Phillips Head Screws
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
HARNESS:
• GMRC-03 - 1997-2002 Cadillac Interface W/O Onstar
• GMOS-06 - 1997-2002 Cadillac Interface W/ Onstar
A
B
D
ANTENNA ADAPTER:
• 40-GM10 - GM Antenna Adapter
C
TOOLS REQUIRED:
• Phillips Screwdriver • Panel Removal Tool • Small Flat Blade Screwdriver • Cutting Tool
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
DASH DISASSEMBLY
95-2004
1997-2001 CADILLAC CATERA
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
3
A
B
C
Remove (1) Phillips head screw from
inside the ashtray and remove ash-
tray. (Figure A)
Remove screw covers from the radio
trim panel. Remove traction control
and hazard switch covers. Then
remove switches by depressing tabs
and pulling outward. (Figure B)
Remove (4) Phillips head screws
from behind covers and ashtray.
4
5
Remove radio trim panel and unplug
any remaining harnesses from the
panel. (Figure C)
Remove (2) Phillips head screws
securing the radio. Unplug and
remove the radio.
6
1996-1999 CADILLAC DEVILLE
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unsnap and remove radio trim panel.
(Open glove box to access.) (Figure A)
2
3
Pinch the side clips to disengage
radio. Unplug and remove radio.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT PREPARATION
1997-2001 CADILLAC CATERA
95-2004
Cut and remove the three shaded
tabs on both brackets. (Figure A)
1
A
1996-1999 CADILLAC DEVILLE
Cut and remove the shaded tab from
both brackets, and both of the tabs
on the trim plate. (Figure B)
1
2
B
Install (4) speed clips into the sub-
dash mounting positions. (Figure C)
C
2
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
95-2004
DOUBLE DIN / STACKED ISO DIN
HEAD UNIT PROVISIONS
Locate the factory wiring harness in
1
the dash. Metra recommends using
the proper mating adapter from
Metra or AXXESS. Re-connect the
negative battery terminal and test
the unit for proper operation.
2
3
Attach the Double DIN brackets to
the inside edge of the Double DIN
trim plate. (Figure A)
Slide the bracket/radio housing
assembly over the Double DIN head
unit and secure using the screws
supplied with the radio. (Figure B)
Reassemble dash in reverse order of
disassembly.
4
3
Download from Www.Somanuals.com. All Manuals Search And Download.
95-2004
NOTES
4
Download from Www.Somanuals.com. All Manuals Search And Download.
95-2004
NOTES
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INST95-2004
METRA. THE WORLD’S BEST KITS.™
1-800-221-0932
REV. 12/01/09
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
INST95-2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|