Metra Electronics Automobile Accessories 99 7877S User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-7877S  
APPLICATIONS  
Honda Fit 2009-10  
99-7877S  
KIT FEATURES  
• DIN Radio Provision with Pocket  
• ISO Mount Radio Provision with Pocket  
• Double DIN Radio Provision  
• Stacked ISO Mount Units Provision  
Painted To Match Factory Dash  
“S”= SILVER  
KIT COMPONENTS  
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets  
• E) Double DIN Trim Plate • F) Pocket  
C
B
D
A
WIRING AND ANTENNA CONNECTIONS  
(Sold Separately)  
70-1729 Honda Harness 2008-up  
• 40-HD10 Honda Antenna Adapter 2005-up  
F
E
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Socket Set  
1-800-221-0932  
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-7877S DASH DISASSEMBLY  
HONDA FIT 2009-10  
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
A
2
3
Unclip and remove the lower center  
panel below radio. (Figure A)  
Remove (1) 8 MM bolt facing up  
behind center panel.  
Note: Slide the recirculation  
control lever to FRESH for better  
access to bolt. (Figure A)  
4
Open the upper glove box then use  
a pry tool to unclip and remove the  
radio/climate control assembly.  
B
(Figure B & C)  
5
6
Remove (2) Phillips screws securing  
the hazard switch to the back of the  
factory radio panel. (Figure D)  
Remove (2) Phillips screws securing  
the air bag light to the back of the  
factory radio panel. (Figure E)  
C
7
8
Remove (5) Phillips screws securing  
the a/c vents to the radio panel.  
Remove (7) retaining clips from radio  
housing to be used later in kit  
preparation.  
Continue to kit preparation.  
D
E
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-7877S KIT PREPARATION  
KIT PREPARATION  
Secure the hazard switch into the  
radio housing panel using the factory  
hardware. (Figure A)  
1
2
3
4
A
Secure the air bag light into the radio  
housing panel using the factory  
hardware. (Figure A)  
Secure the a/c vents to the radio  
housing using the factory hardware.  
(Figure B)  
Attach the (7) retaining clips to the  
radio housing panel in the same  
location as removed from the factory  
radio panel.  
B
Continue to kit assembly.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-7877S KIT ASSEMBLY  
DIN MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Locate the factory wiring harness in  
the dash. Metra recommends using  
the proper mating adapter from  
Metra or AXXESS. Re-connect the  
negative battery terminal and test  
the unit for proper operation.  
A
B
C
Slide the DIN cage into the Radio  
Housing and secure by bending the  
metal locking tabs down. (Figure A)  
3
4
Slide the aftermarket head unit into  
the cage and secure. (Figure B)  
Snap the pocket into the Radio  
Housing. (Figure C)  
5
Re-assemble dash in reverse order of  
disassembly.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-7877S KIT ASSEMBLY  
ISO MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
Locate the factory wiring harness in  
A
the dash. Metra recommends using  
the proper mating adapter from Metra  
or AXXESS. Re-connect the negative  
battery terminal and test the unit for  
proper operation.  
2
3
Mount the ISO Brackets to the head  
unit with the screws supplied with  
the unit. (Figure A)  
Slide the head unit into the radio  
opening until the side clips engage.  
(Figure B)  
B
4
5
6
Snap the Trim plate into the Radio  
Housing. (Figure B)  
Snap the Pocket into the radio  
housing. (Figure C)  
Re-assemble dash in reverse order of  
disassembly.  
C
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-7877S KIT ASSEMBLY  
DOUBLE DIN RADIO PROVISION/  
STACKED ISO MOUNT UNITS PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
Locate the factory wiring harness in  
the dash. Metra recommends using  
the proper mating adapter from Metra  
or AXXESS. Re-connect the negative  
battery terminal and test the unit for  
proper operation.  
A
B
C
2
3
Cut and remove the center bar from  
the radio housing. (Figure A)  
Snap the Double DIN brackets to the  
inside edge of the Radio Housing.  
(Figure B)  
4
Slide the Double DIN head unit or  
stacked ISO head units into the  
bracket/radio housing assembly and  
secure the Double DIN head unit or  
stacked ISO head units to the  
assembly using the screws supplied  
with the radio. (Figure C)  
5
6
Snap the Double DIN trim plate onto  
the front of the radio/housing  
assembly. (Figure C)  
Re-assemble dash in reverse order of  
disassembly.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-7877S INSTRUCTIONS  
1-800-221-0932  
REV. 4/22/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7877  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LaCie Bike Rack 12big rack Serial User Manual
Laser MP3 Player MP4 P13 User Manual
Lastolite Camera Accessories B90008 User Manual
Learning Resources Marine GPS System LER 3240 User Manual
LG Electronics Projection Television 52SX4D User Manual
Lightolier Indoor Furnishings 1101FDL User Manual
Lightolier Work Light C4T4VM User Manual
Makita Cordless Saw JR3030 User Manual
Makita Power Hammer HR3851 User Manual
Midland Radio Two Way Radio LXT480 Series User Manual