Metra Electronics Automobile Accessories 99 5816 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-5816  
APPLICATIONS  
FORD Focus  
2008-2011  
99-5816  
KIT FEATURES  
• DIN Radio Provision with Pocket  
• ISO Mount Radio Provision with Pocket  
• Double DIN Radio Provision  
• Stacked ISO Mount Units Provision  
• Painted To Match Factory Dash  
KIT COMPONENTS  
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets  
• E) Double DIN Trim Plate • F) Pocket • G) (2) Top Clips and (4) Middle Radio Housing Clips  
D
E
B
C
A
SIDE VIEW  
SIDE VIEW  
Wiring & Antenna Connections (sold seperately)  
XSVI-5520-NAV - Ford Interface  
AFSI-02 - if equipped w/ sync  
G
70-5522 - Ford Sub Harness  
F
(2) TOP CLIPS (4) MIDDLE CLIPS  
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Socket Set • Cutting Tool  
1-800-221-0932  
© COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-5816 DASH DISASSEMBLY  
FORD FOCUS 2008-2011  
A
1
2
3
4
Disconnect the negative battery termi-  
nal to prevent an accidental short cir-  
cuit.  
Unclip and remove the trim panel sur-  
rounding the shifter and including the  
cup holders. (Figure A)  
Remove (2) 9/32” screws from the bot-  
tom edge of the factory radio trim  
panel. (Figure B)  
Remove (2) 9/32” screws facing up  
above the gauge cluster then unclip  
and remove the trim panel surrounding  
the gauge cluster. (Figure C)  
B
5
Unclip and remove the trim panel  
above the glove box. (Figure D)  
Continue on page 2.  
C
D
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-5816 DASH DISASSEMBLY  
FORD FOCUS 2008-2011  
6
Unclip and remove the vent panel at  
the top of the factory radio trim panel.  
E
(Figure E)  
7
8
Remove (2) 9/32” screws behind the  
vent panel removed in step 6.  
(Figure F)  
Unclip the factory radio trim panel  
assembly. Unplug and remove the  
assembly. Note: Some early models  
had a ground strap attached to the  
radio chassis and the sub dash with  
an 8 MM bolt. You will need to unbolt  
this strap to remove the factory radio  
trim panel assembly.  
9
Remove (4) T-20 Torx screws securing  
the climate controls to the factory  
radio trim panel assembly and  
remove the controls from the assem-  
bly. (Retain the screws and climate  
controls for re-use during kit prepara-  
tion.) (Figure G)  
1
2
3
8
4
9
5
6
7
F
0
10 Remove (4) T-20 Torx screws securing  
the accessory socket panel to the  
factory radio trim panel assembly and  
remove the socket panel from the  
assembly. (Retain the screws and  
accessory socket panel for re-use  
during kit preparation.) (Figure G)  
11 Unclip and remove the passenger air  
bag light and the switch panel blank  
plates. (Retain the air bag light and  
blank plates for re-use during kit  
preparation.) (Figure G)  
Continue to kit preparation.  
G
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816 KIT ASSEMBLY  
KIT PREPARATION  
A
Secure the climate control into the  
radio housing using the factory hard-  
ware. (Figure A)  
1
2
Secure the accessory socket panel to  
the radio housing using the factory  
hardware. (Figure B)  
Clip the passenger air bag light and  
the switch panel blank plates in to  
the radio housing. (Figure C)  
3
4
Attach Top and Middle Radio Housing  
Clips to the back of the radio housing.  
(
Figure D,E)  
B
NOTE: When the clips are properly  
attached they should be on a 90  
degree angle with the radio housing.  
SIDE VIEW  
FRONT VIEW  
FRONT VIEW SIDE VIEW  
D
E
(2) TOP CLIPS  
(4) MIDDLE CLIPS  
C
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816 KIT ASSEMBLY  
DIN MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
Slide the DIN cage into the radio hous-  
ing and secure by bending the metal  
locking tabs outward. (Figure A)  
1
2
3
Slide the aftermarket radio into the DIN  
cage and until it snaps into place.  
Snap the pocket into the radio housing.  
(Figure C)  
Continue to final assembly.  
B
C
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816 KIT ASSEMBLY  
ISO MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
Mount the ISO Brackets to the radio  
using the screws supplied with the  
radio. (Figure A)  
2
3
4
Slide the radio into the radio housing  
until it snaps into place. (Figure B)  
Snap the trim plate onto the front of  
the Radio Housing. (Figure B)  
Snap the Pocket into the radio  
housing. (Figure C)  
Continue to final assembly.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816 KIT ASSEMBLY  
DOUBLE DIN/STACKED ISO MOUNT  
UNITS RADIO PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Cut and remove the center bar from  
the radio housing. (Figure A)  
Snap the Double DIN brackets to the  
inside edge of the radio housing.  
(Figure B)  
3
Slide the Double DIN or stacked ISO  
mount unit(s) into the bracket/radio  
housing assembly and secure the  
unit(s) to the assembly using the  
screws supplied with the unit(s).  
(Figure C)  
4
Snap the double DIN trim plate onto  
the front of the radio housing.  
(Figure C)  
Continue to final assembly.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816 FINAL ASSEMBLY  
FINAL ASSEMBLY  
A
B
(A) Strip wire ends back 1/2"  
B) Twist ends together  
C) Solder  
D) Tape  
C
D
Locate the factory wiring harness in the dash. Metra recommends using the  
proper mating adapter and making connections as shown. (Isolate and individ-  
ually tape off the ends of any unused wires to prevent electrical short circuit.)  
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the  
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and  
individually tape off ends of any unused wires to prevent electrical short circuit.  
METRA / EIA WIRING CODE  
12V Ignition / Acc. . . . . . . . . . Red  
Right Front (+) . . . . . . . . . . . . Gray  
12V Batt / Memory. . . . . . . . . Yellow  
Ground. . . . . . . . . . . . . . . . . . Black*  
Power Antenna. . . . . . . . . . . . Blue  
Right Front (-). . . . . . . . . . . . . Gray/ Black  
Left Front (+) . . . . . . . . . . . . . White  
Left Front (-). . . . . . . . . . . . . . White / Black  
Right Rear (+) . . . . . . . . . . . . Violet  
Amp Turn-On . . . . . . . . . . . . . Blue / White  
Amp Ground. . . . . . . . . . . . . . Black / White  
Illumination . . . . . . . . . . . . . . Orange  
Dimmer . . . . . . . . . . . . . . . . . Orange / White  
Right Rear (-) . . . . . . . . . . . . . Violet / Black  
Left Rear (+) . . . . . . . . . . . . . Green  
Left Rear (-) . . . . . . . . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816  
NOTES  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816  
NOTES  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
99-5816 INSTRUCTIONS  
1-800-221-0932  
REV. 11/18/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-5816  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lexmark All in One Printer 30E User Manual
LG Electronics Air Conditioner LP6000ER User Manual
Liebert Surge Protector SERIES 300 UPS User Manual
Lincoln Electric Welder US F146 User Manual
Linear Automobile Electronics LRA User Manual
Linksys Network Router RT042 User Manual
Makita Cordless Saw 5092D User Manual
Marantz Stereo System SR 19 User Manual
Melissa Scale 746 081 User Manual
Metrologic Instruments PDAs Smartphones SP5700 Series User Manual