LG
Window-Type Air Conditioner
LG
OWNER'S MANUAL
MODELS: LP6000ER
LP7000R
IMPORTANT
Please read through this manual. It contains valuable
information about your air conditioner. This manual may help
save time and money by explaining proper air conditioner
maintenance and preventing improper use.
PRECAUTIONS
Pay close attention to precautions in order to prevent
potential hazards and damage from misuse or improper
installation. LG is not responsible for any damages caused by
misuse of the air conditioner.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Precautions
Precautions
To prevent injury and property damage, follow these instructions.
Incorrect operation due to ignoring instructions might cause harm or damage, the seriousness of which is
indicated by the following symbols.
This symbol shows the possibility of death or serious injury.
WARNING
This symbol indicates the possibility of injury or damage to property.
CAUTION
Never Do This
Always Do This
■ The following items are classified by these symbols.
WARNING
WARNING
Plug in the power plug
properly.
Do not operate or stop the
unit by inserting or pulling
out the power plug.
Do not damage or use an
unspecified power cord.
• Doing so may cause electric
shock or fire due to heat
generation or electric shock.
• Doing so may cause electric
shock or fire due to heat
generation.
• Doing so may cause electric shock or fire.
•
If the supply cord is damaged, it must be replaced
by the manufacturer, the manufacturer's service
agent, or a similarly qualified person in order to
avoid a hazard. (Y attachment)
Do not modify power cord
length or share the outlet
with other appliances.
Do not operate with wet
hands or in damp
environment.
Do not direct airflow at
room occupants only.
• Doing so may cause electric shock or • Doing so may cause electric
• This could damage your health.
fire due to heat generation.
shock.
Always plug into a
grounded outlet.
Do not allow water to run
into electric parts.
Always install air leakage
breaker and a dedicated
switching board.
• No grounding may cause electric
shock (See Installation Manual).
• Doing so may cause failure of
machine or electric shock.
• Failure to install these may cause
fire or electric shock accident.
Unplug the unit if strange
sounds, odors, or smoke
comes from it.
Do not use the socket if it is
loose or damaged.
Do not open the entrance
during operation.
• Such a unit may pose a risk of
fire or electric shock accident.
• Doing so may cause fire or
electric shock.
• It may cause electric shock.
Keep firearms away.
Do not use the power cord
close to heating tools.
Do not use the power cord near
flammable gas or combustibles such
as gasoline, benzene, thinner, etc.
• Doing so may cause fire or
electric shock.
• Doing so may lead to an
explosion or fire.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
WARNING
Ventilate before operating air conditioner
when gas goes out.
Do not disassemble or modify products
randomly.
• Operating the air conditioner in the presence of gas • Doing so may cause failure or electric shock.
vapors can lead to explosions and fire.
CAUTION
CAUTION
Never touch the metal parts
of the unit when removing
the filter.
Do not clean the air
conditioner with water.
Operate only in a well
ventilated area when using in
the presence of a stove, etc.
• They are sharp and may cause
injury.
• Water may enter the unit and
degrade the insulation. It also
may cause an electric shock.
• An oxygen shortage may
otherwise occur.
When cleaning the unit, first
make sure the power is off
and the cord is unplugged.
Do not put a pet or house
plant where it will be exposed
to direct air flow.
Do not use appliance for special
purpose such as climate control for
animals or vegetables, precision
machine, or conservation of art articles.
•
Since the fan rotates at high speed • This could injure the pet or plant. • It may cause damage of animals
during operation, it may cause
injury if activated while cleaning.
or vegetables or loss of property.
Stop operation in storm or
hurricanes.
Hold the plug by the head
when taking it out.
Turn off the main power
switch when not using it for
a long time.
• Operation with windows opened
may cause wetting of indoor and
soaking of household furniture.
• Improper handling may cause
electric shock or damage.
• Doing so can prolong the life of
the product.
Do not place obstacles
around the absorption inlet
or output.
Ensure that an installation console of
the outdoor appliance is not damaged
due to extened use.
Always insert filters
securely. Clean them every
two weeks.
• Doing so may cause failure of
appliance or accident.
• If the previous air conditioner
damaged the console, there is a
risk of the new unit falling.
• Operation without filters will
cause failure.
Do not use abrasives or strong
detergent such as wax or
thinner. Always use a soft cloth.
Do not place heavy object on the
power cord and take care so that
the cord is not pinched.
Do not drink water drained
from air conditioner.
• Otherwise, the products appearance may
be damaged due to change of product
color or scratching of its surface.
• Treating the power cord
carelessly poses a danger of fire
or electric shock.
• It contains contaminants that
would make you sick.
If water enters the product, turn off the the
power switch of the main body of appliance.
Contact service center after taking the
power-plug out from the socket.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Prior to Operation
Precautions
Preparing for operation
1
2
3
4
5
6
Contact an installation specialist for installation.
Plug in the power plug properly.
Do not share the same outlet with other appliances
Do not use an extension cord.
Do not start/stop operation by plugging/unplugging the power cord.
If cord/plug is damaged, replace only with an authorized part.
Usage
1
2
3
Being exposed to direct airflow for an extended period of time could be hazardous to your health. Do not
expose occupants, pets, or plants to direct airflow for extended periods of time.
Due to the possibility of oxygen deficiency, ventilate the room when using together with stoves or other
heating devices.
Do not use this air conditioner for non-specified special purposes (e.g. preserving precision devices,
food, pets, plants, and art objects). Usage in such a manner could harm such property.
Cleaning and maintenance
1
2
3
Do not touch the metal parts of the unit when removing the filter. Injuries can occur when handling sharp
metal edges.
Do not use water to clean inside the air conditioner. Exposure to water can destroy the insulation, leading
to possible electric shock.
When cleaning the unit, first make sure that the power and breaker are turned off. The fan rotates at a
very high speed during operation. There is a possibility of injury if the unit’s power is accidentally
triggered on while cleaning inner parts of the unit.
Service
For repair and maintenance, contact your authorized service dealer.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Remote Control Operations
Instructions
The remote control and control panel will look like those represented in the following pictures.
1
6
3
Power
1
Temp
2
4
3
Fan Speed
Timer
Mode
5
Auto
Swing
4
2
5
Remote Control Operations
1
4
POWER
FAN SPEED
• To turn the air conditioner ON, push this button.
To turn the air conditioner OFF, push the button
again.
• Every time you push this button, it advances the
setting as follows: {High(F3) ■ Low(F1) ■
Med(F2) ■ High(F3)}
• This button takes priority over any other button.
• When you first turn it on, the unit is in cool mode,
high fan speed, temperature setting at 72˚F.
5
TIMER
- SHUT-OFF TIME
• You will usually use shut-off time while you
sleep.
• With unit running, use Timer to set number of
hours until shut-off.
• For your sleeping comfort, once Time is set, the
Temperature setting will raise 2°F after 30 min,
and 2°F after another 30 min.
• Every time you push Timer button, it advances
the Timer setting as follows: 1 Hour ■ 2 Hours ■
etc. ■ 12 Hours maximum.
- START TIME
• With unit not running, use timer to set number of
hours before unit starts.
• Every time you push Timer button, it advances
the Timer setting as follows: 1 Hour ■ 2 Hours ■
etc. ■ 12 Hours maximum.
2
3
TEMPERATURE SETTING
• Use this button to automatically control the
temperature of the room.
The temperature can be set within a range of
60°F to 86°F by increments of 1°F.
MODE
- Every time you push this button, it will cycle
through the following modes: COOL, ENERGY
SAVER, FAN and DRY.
- ENERGY SAVER
• The fan stops when the compressor stops
cooling. Approximately every 3 minutes the fan
will turn on and the unit will check the room air to
determine if cooling is needed.
6
REMOTE CONTROL SENSOR
AUTO RESTART
When power is restored after an electrical power failure, the unit will begin to run at its last setting.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting the Remote Control Batteries
1
2
3
Push out the cover on the back of the remote control with your thumb.
Pay attention to polarity and insert two new AAA 1.5V batteries.
Reattach the cover.
NOTE: Do not use rechargeable batteries. Make sure that both batteries are new.
• In order to prevent discharge, remove the batteries from the remote control if the
air conditioner is not going to be used for an extended period of time
Keep the remote control away from extremely hot or humid places.
To maintain optimal operation of the remote control, the remote sensor should not
be exposed to direct sunlight.
• The remote control can be mounted on a wall using the mountable holder.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Adjusting the Air Flow Direction
Instructions
Adjusting the Air Flow Direction
Airflow can be adjusted by changing the direction of the air conditioner's louvers. This can also increase the
cooling efficiency of the air conditioner.
• Adjusting Horizontal Air Flow Direction
Adjusting the vertical louvers left and right will
change horizontal airflow.
• Adjusting Vertical Air Flow Direction
Adjusting the horizontal vane up and down will
change vertical airflow. The vane can be adjusted
by nudging the vane backward or forward.
Adjusting horizontal air flow
Adjusting vertical air flow
• Recommended orientation of louvers
Adjust louvers to face upwards when cooling to maximize cooling efficiency.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and
Care and Maintenance
Maintenance
Turn the power off and unplug the power plug before cleaning the air conditioner.
Air Filter
The Air Filter will become dirty as it removes dust from the inside air. It should be washed at least every 2 weeks.
If the Air Filter remains full of dust, the air flow will decrease and the cooling capacity will be reduced, possibly
damaging the unit.
How to remove the air filter
1
2
Pull the inlet grille forward, grasping both tabs, then
pull out the air filter.
Wash the Air Filter under the faucet with warm water.
Be sure to shake off all the water before replacing the
filter.
NOTE : In humid weather, excess water may cause the
BASE PAN to overflow and be splashed on the louver.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware
Hardware Installation
Installation
Remote Control Operations
Product Features
CAUTION
This appliance should be installed in accordance with national wiring regulations. The following
information serves acts as a guide to help to explain product features.
P
o
w
er
T
e
m
p
F
an
S
p
ee
d
S
le
ep
M
o
d
e
7
5
6
4
2
3
1
8
11 13
9
12
10 14 15
1. CABINET
8. TOP COVER
2. VERTICAL AIR DEFLECTOR
(HORIZONTAL LOUVER)
9. EVAPORATOR
10. CONDENSER
11. COMPRESSOR
12. BASE PAN
3. HORIZONTAL AIR DEFLECTOR
(VERTICAL LOUVER)
4. FRONT GRILLE
13. POWER CORD
14. BRACE
5. AIR INTAKE (INLET GRILLE)
6. AIR FILTER
15. REMOTE CONTROLLER
7. CONTROL PANEL
10
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Install the Unit
1
2
3
To prevent vibration and noise, make sure the unit
is installed securely and firmly.
Fence
Cooled air
Awning
Install the unit where the sunlight does not shine
directly on the unit.
Heat
radiation
The outside of the cabinet must extend outward
and there should be no obstacles, such as a fence
or wall, within 20" from the back of the cabinet
because it will prevent heat radiation of the
condenser.
About 1/4"
Over 20"
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure.
4
5
Install the unit a little slanted so the back is slightly lower than the front (about 1/4").
This will force condensed water to flow to the outside.
Install the unit with the bottom about 30"~60" above the floor level.
Window Requirements
NOTE: All supporting parts should be secured to firm wood, masonry, or metal.
• This unit is designed for installation in standard double
hung windows with actual opening widths from 26"
to 39 3/8".
Sash
• The top and bottom window sash must open sufficiently
to allow a clear vertical opening of 12" from the bottom
of the upper sash to the window stool.
26"(660mm) to
393/8"(1000mm)
12"(305mm) min.
Window
Offset
Sill
Inner sill
Exterior
Interior wall
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Kits Contents
ITEM
NAME OF PARTS
Q'TY
A
B
C
A
B
C
D
E
F
SUPPORT, BRACKET
LEVELING BOLT
LEVELING BOLT
SCREW: 5/8"
1
1
1
2
5
1
1
1
G
F
E
D
SCREW: 5/8"
H
FOAM SEAL
G
H
FOAM STRIP
L BRACKET
Suggested Tool Requirements
SCREWDRIVER(Phillips and Flathead), RULER, KNIFE, HAMMER, PENCIL, LEVEL
Installation
CAUTION
How to Install
To avoid the possibility of personal injury, unplug
power to unit before installing or servicing.
1
Cut the FOAM STRIP (ITEM G) to fit the
underside of the window sash. Open the window, peel
off the backing and attach the FOAM STRIP as shown
in FIG. 1.
Carefully remove air conditioner from carton, check
for possible shipping damage. Pick a location which
will allow you to blow the cold air into the area you
want. Windows used for installation must be strong
enough to support the weight of the air conditioner.
Good installation with special attention to the proper
position of the unit will lessen the chance that service
will be needed.
FOAM STRIP
(ITEM G)
FIG. 1
When cooling more than one room, installation
location is very important. To cool your rooms, cold air
must be blown from the air conditioner in a straight
path.
If air conditioner is blocked by a storm window frame,
see Step 7 and 8 on Page 14 before beginning to
install.
2
Mark center line with pencil on the center of the
inner sill, as shown in FIG. 2.
INDOOR
FIG. 2
INNER SILL
CENTER LINE
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Install support bracket on window. See FIG. 3.
INSTALL THE AIR CONDITIONER IN
Install leveling bolt up through bottom side of support
bracket. You can choose a short bolt (ITEM C) or a
long one (ITEM B) according to window type. Also,
you should select the position of hole on bracket.
Position bracket on sill 1 inch (25.4mm) to left of
center line of window (See FIG. 3).
Fasten bracket loosely to sill with screws (ITEM D)
provided.
Adjust leveling bolt so that the air conditioner will be
installed with a very slight tilt (about 1/4") downward
toward the outside for proper drainage. Tighten
bracket screws.
THE WINDOW
• Carefully lift the air conditioner and slide it into the
open window. Be careful not to hurt waist in this
operation.
• Use the two hand grips on top sides of unit to lift
unit.
• Make sure that support bracket is inserted in the
pocket under base fan, and that curtain frame guide
is stopped by stopper on the support bracket as
shown in FIG.6.
NOTE: When unit is properly centered and pushed
outward to correct bracket location, you will feel unit
drop securely in place on the support bracket. Hold
unit firmly during this procedure.
• Lower top window sash all the way down so that
sash sits firmly in top channel of unit and
expandable curtain frames.
OUTER
WINDOW CLOSE-UP VIEW
SILL
OF SUPPORT BRACKET
(ITEM A)
SCREW
(ITEM D)
CAUTION
ADJUSTMENT SLOT
During the following step, hold unit firmly until
window sash is lowered to top channel behind
curtain frames. Personal injury or property damage
may result if unit falls from window.
LEVELING BOLT
(ITEM B or C)
INNER
WINDOW
SILL
1"(25.4mm)
CENTER LINE
OF WINDOW
FIG. 3
SCREW
SUPPORT
BRACKET
ABOUT 1/4"
INNER SILL
LEVELING
BOLT
FIG. 5
CENTER LINE
OUTER SILL
WINDOW SASH
TOP CHANNEL
HAND GRIP
INDOOR
OUTDOOR
INDOOR
SECTION
OUTDOOR
SECTION
FIG. 4
SUPPORT
BRACKET
POCKET
CAUTION
CURTAIN
INNER SILL
SUPPORT
BRACKET
STOPPER
Failure to securely install support bracket may
result in unit falling from window if window sash is
raised after unit is installed. This could result in
personal injury.
LEVELING BOLT
OUTER SILL
INDOOR
OUTDOOR
FIG. 6
13
Download from Www.Somanuals.com. All Manuals Search And Download.
5
7
SECURE THE CURTAIN FRAMES
IF AIR CONDITIONER IS BLOCKED
BY STORM WINDOW FRAME
Expand the curtain frames and secure them using 5
screws (ITEM E) as shown in FIG. 7.
When curtain frame opens or closes, you may feel a
slight resistance. This is normal.
• If storm window presents interference, fasten a
2"(51mm) wide wood strip to the inner window sill
across the full width of the sill. The wood strip should
be thick enough to raise the height of the window sill
so that unit can be installed without interference
from the the storm window frame. See FIG. 8.
Top of wood strip should be approximately
6
FOAM SEAL AND WINDOW LOCK
• Cut the foam seal (ITEM F) to the window width.
Stuff the foam seal between the glass and the
window to prevent air and insects from getting into
the room, as shown in FIG.7.
3/4"(19mm) higher than the storm window frame to
help condensation to drain properly to the outside.
• Install the L bracket to prevent window from being
raised which may result in unit falling.
• Install a second wood strip (approximately
6"(152mm) long by 11/2"(38mm) wide and same
thickness as first strip) in the center of the outer sill
flush against the back of the inner sill. (FIG. 8)
L BRACKET
FOAM SEAL
(ITEM F)
1 1/2" min.
3/4"(19mm)
(38mm)
WOOD STRIP MOUNTED
ON TOP OF INNER SILL
CLEARANCE
STORM
WINDOW
FRAME
INNER
SILL
ITEM E
WOOD STRIP
FOR SUUPPORT
BRACKET
OUTER
SILL
INDOOR
OUTDOOR
When storm window
frame is located on outer sill
FIG. 7
FIG. 8
CAUTION
8
INSTALLATION FOR OTHER TYPE
WINDOWS.
Failure to securely install support bracket may
result in unit falling from window if window sash is
raised after unit is installed. This could result in
personal injury.
• Dimensions and geometry of windows are different
according to manufacturers. Check your window and
refer to FIG.9 to install the support bracket firmly.
NOTE: If window sash has a metal surface. use sheet
metal screws instead of the provided wood screws.
Obtain sheet metal screws at local hardware store.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVAL FROM WINDOW
• Turn off and unplug the air conditioner.
• Unscrew the side screws that you installed in Step 5.
6.
(a) When window frame is located on inner sill.
• Install a wood strip (window width long and
window frame height high) on the inner sill.
• Close the curtain frame and remove foam seal and L
bracket from the windows.
SASH WINDOW
• Keep a firm grip on the air as you the sash.
• Lift the air conditioner from the window and remove
the foam strip from between the windows.
• Remove the support bracket from window frame.
WINDOW FRAME
WOOD STRIP
INNER
SILL
NOTE: When cooling season is over, unit is removed
from window for cleaning and storage. There may still
be some condensation water in the basepan. Remove
the unit carefully to avoid water being spilled out on
floor. Always store unit flat on its base. Do not stand it
on its end. Be sure to remove support bracket, L
bracket, and foam seal from window and save.
Window will not close if support bracket remains
installed.
OUTER
SILL
(b) When the window frame is higher than
19/32"(15mm)
• Install a wood strip (about 4"(102mm) long) on
the outdoor sill to raise support bracket.
CAUTION
WINDOW FRAME
19/32"(15mm)
WOOD STRIP
• Air conditioners covered in this manual pose an
excessive weight hazard. Two or more people are
needed to move and install the unit.
To prevent injury or strain, use proper lifting and
carrying techniques when moving unit.
INNER
SILL
• When handling the air conditioner, be careful to
avoid cuts from sharp metal fins on front and rear
coils.
OUTER
SILL
FIG. 9
• Make sure air conditioner does not fall during
removal.
Electrical Safety
Line Cord Plug
Use Wall Receptacle
Power Supply
Do not under any
circumstances cut
or remove the
grounding prong
from the plug.
Use 15 AMP, time
delay fuse or circuit
breaker.
Power supply cord with
3-prong grounding plug
Standard 125V, 3-wire grounding
receptacle rated 15A, 125V AC
Use of extension cords
• Because of potential safety hazards, we strongly discourage the use of an extension cord. However, if you wish
to use an extension cord, use a CSA certified/UL-listed 3-wire (grounding) extension cord, rated at 15A, 125V.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Safety
Because of potential safety hazards, we strongly
discourage the use of an adapter plug. However, if you
wish to use an adapter, a TEMPORARY
CONNECTION may be made. Use UL-listed adapter,
available from most local hardware stores (FIG. 11).
The large slot in the adapter must be aligned with the
large slot in the receptacle to assure a proper polarity
connection.
IMPORTANT
(PLEASE READ CAREFULLY)
FOR THE USER'S PERSONAL SAFETY, THIS
APPLIANCE MUST BE PROPERLY GROUNDED
The power cord of this appliance is equipped with a
three-prong (grounding) plug. Use this with a standard
three-slot (grounding) wall power outlet (FIG. 10) to
minimize the hazard of electric shock. The customer
should have the wall receptacle and circuit checked by
a qualified electrician to make sure the receptacle is
properly grounded.
CAUTION: Attaching the adapter ground terminal to
the wall receptacle cover screw does not
ground the appliance unless the cover
screw is metal, and not insulated, and the
wall receptacle is grounded through the
house wiring. The customer should have
the circuit checked by a qualified electrician
to make sure the receptacle is properly
grounded.
PREFERRED METHOD
Disconnect the power cord from the adapter, using one
hand on each. Otherwise, the adapter ground terminal
might break. DO NOT USE the appliance with a
broken adapter plug.
Ensure proper ground
exists before use
B. SITUATIONS WHEN THE APPLIANCE WILL BE
DISCONNECTED OFTEN.
FIG. 10
Do not use an adapter plug in these situations.
Unplugging the power cord frequently can lead to an
eventual breakage of the ground terminal. The wall
power outlet should be replaced by a three-slot
(grounding) outlet instead.
DO NOT CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER PLUG.
A. SITUATIONS WHEN THE APPLIANCE WILL BE
DISCONNECTED OCCASIONALLY:
USE OF EXTENSION CORDS
TEMPORARY METHOD
Because of potential safety hazards, we strongly
discourage the use of an extension cord. However, if
you wish to use an extension cord, use a CSA
certified/UL-listed 3-wire (grounding) extension cord,
rated at 15A, 125V.
Adapter plug
Metal screw
Receptacle cover
FIG. 11
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Common
Issues
Common Problems and Solutions
Before calling for service, please review the following list of common problems and solutions.
The air conditioner is operating normally when:
• You hear a pinging noise. This is caused by water being picked up by the condenser on rainy days or in highly
humid conditions. This feature is designed to help remove moisture in the air and improve cooling efficiency.
• You hear the thermostat click. This is caused by the compressor cycle starting and stopping.
• You see water dripping from the rear of the unit. Water may be collected in the base pan in highly humid
conditions or on rainy days. This water overflows and drips from the rear of the unit.
• You hear the fan running while the compressor is silent or fan mode. This is a normal operational feature.
The air conditioner may be operating abnormally when:
Problem
Possible Causes
What To Do
■ The air conditioner is unplugged or • Make sure the plug is completely plugged into
not plugged in completely. the outlet.
■ The fuse is blown/circuit breaker is • Check the fuse/circuit breaker box and replace
The air conditioner
does not operate
at all
triggered.
the fuse or reset the breaker.
■ Power failure.
• In the event of a power failure, set the power
control to OFF. When the power is restored,
wait 3 minutes to restart the air conditioner to
prevent the compressor from overloading.
■ Air flow is restricted.
• Make sure there are no curtains, blinds,
furniture or other obstacles in front of the air
conditioner.
■ TEMP Control set too higher
• Set the TEMP control to a lower number.
number.
■ The air filter is dirty.
• Clean the filter at least every 2 weeks. Refer to
the "Care and Maintenance" section (p.8) of the
manual.
Air conditioner
does not cool
■ The air conditioner was just
turned on.
• After the air conditioner is turned on, you need
to give the air conditioner some time to cool the
room.
■ Cold air is escaping.
• Check for open furnace floor resisters and cold
air returns.
• CLOSE the air conditioner vent.
■ Cooling coils are iced up.
• See Ice appears on the air conditioner below
■ The cooling coils are iced over.
• Ice may block the air flow and obstruct the air
conditioner from properly cooling the room.
Set the mode control at High Fan or High Cool
with the high temperature.
Ice appears on the
air conditioner.
■ You can refer to the Energy Star program in detail at "www.energystar.gov".
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|