Metra Electronics Automobile Accessories 99 1008 User Manual |
INSTA LLATION INSTRUCTIONS FOR PA RT 9 9 -10 0 8
APPLICATIONS
• 2003-2006 Kia Sorento LX
• 2004.5-2006 Kia Spectra
9 9 -10 0 8
• Recessed DIN Head Unit
KIT FEATURES
• ISO Head Unit Provisions with Pocket
KIT COMPONENTS
A) Radio Housing
I
B) ISO Brackets
I
C) Trim Plate
A
C
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver I Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -10 0 8
2 0 0 3 -2 0 0 6 KIA SORENTO LX
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Open ash tray and unsnap and
remove outside trim panels.
(Figure A)
Tip: Start at the bottom of the trim
panels.
B
3
Remove (8) Phillips screw from the
radio trim panel. Disconnect any
plugs from the trim panel and then
remove panel. (Figure B)
C
4
5
Remove (4) Phillips screw from radio
to remove radio. (Figure C)
Cut along the scored lines of the
radio housing’s mounting tabs.
(Figure D)
D
1
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -10 0 8
2 0 0 4 .5 - 2 0 0 6 KIA SP ECTRA
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Using a flat blade screwdriver as a
pry tool, unsnap and remove the
center dash panel including the cli-
mate controls and vents from around
the radio. (Figure A)
B
Remove (4) phillips screws to
3
remove radio. (Figure B)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -10 0 8
DIN HEA D UNIT P ROVISION
A
Slide the DIN cage into the Radio
Housing and secure by bending the
1
metal locking tabs down. (Figure A)
Slide the aftermarket head unit into
the cage and secure.
2
Snap the Trim plate into the Radio Housing.
3
ISO DIN HEA D UNIT P ROVISION
A
Mount the ISO Brackets to the head
unit with the screws supplied with
1
the unit.
Slide the head unit into the radio
opening until the side clips
2
engage. (Figure A)
Snap the Trim plate into the Radio
Housing.
3
3
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -10 0 8
A
B
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
C
D
Tape
Locate the factory wiring harness in the
1
dash. Metra recommends using the proper
mating adapter and making the connections
as shown. (Isolate and individually tape off
the ends of any unused wires to prevent
electrical short circuit)
2
3
Re-connect the negative battery terminal and test
the unit for proper operation.
Reassemble in reverse order of disassembly.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
9 9 -10 0 8
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INST9 9 10 0 8
1-800-221-0932
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION Rev. 06-13-07
Download from Www.Somanuals.com. All Manuals Search And Download.
|