Meridian Audio Home Theater System FDP DILA2 User Manual

Home Theater Optimized  
FDP-DILA2  
Installation and  
Operations Manual  
NOTICE: THIS PROJECTOR HAS BEEN SIGNIFICANTLY  
MODIFIED AND OPTIMIZED TO PRODUCE VERY HIGH  
QUALITY IMAGES USING THE FAROUDJA PROCESSOR.  
ANY CHANGES MADE TO THESE SETTINGS CAN CORRUPT  
THIS PROCESS. RESETTING THE OPTIMIZATION IS NOT  
COVERED UNDER WARRANTY.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY PRECAUTIONS  
IMPORTANT INFORMATION IMPORTANT SAFEGUARDS  
Electrical energy can perform many useful functions. This  
unit has been engineered and manufactured to assure your  
WARNING :  
personal safety. But IMPROPER USE CAN RESULT IN  
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In  
order not to defeat the safeguards incorporated into this  
product, observe the following basic rules for its installation,  
use and service. Please read these “Important Safeguards”  
carefully before use.  
TO PREVENT FIRE OR SHOCK HAZARDS, DO  
NOT EXPOSE THIS APPLIANCE TO RAIN OR  
MOISTURE.  
CAUTION :  
All the safety and operating instructions should be read  
before the product is operated.  
To reduce the risk of electric shock, do not remove  
cover.  
The safety and operating instructions should be retained  
for future reference.  
Refer servicing to qualified service personnel.  
All warnings on the product and in the operating  
instructions should be adhered to.  
This projector is equipped with a 3-blade grounding-type  
plug to satisfy FCC rule. If you are unable to insert the  
plug into the outlet, contact your electrician.  
All operating instructions should be followed.  
Place the projector near a wall outlet where the plug can  
be easily unplugged.  
Unplug this product from the wall outlet before cleaning.  
Do not use liquid cleaners or aerosol cleaners. Use a  
damp cloth for cleaning.  
FCC INFORMATION (U.S.A. ONLY)  
CAUTION :  
Do not use attachments not recommended by the  
product manufacturer as they may be hazardous.  
Changes or modification not approved by Faroudja could  
void the user’s authority to operate the equipment.  
Do not use this product near water. Do not use  
immediately after moving from a low temperature to high  
temperature, as this causes condensation, which may  
result in fire, electric shock, or other hazards.  
NOTE :  
This equipment has been tested and found to comply  
with the limits for a Class B digital devices, pursuant to  
Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful  
Do not place this product on an unstable cart, stand, or  
table. The product may fall, causing serious injury to a  
child or adult, and serious damage to the product. The  
product should be mounted according to the  
manufacturer’s instructions, and should use a mount  
recommended by the manufacturer.  
interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that  
interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio  
or television reception, which can be determined by  
turning the equipment off and on, the user is encourage  
to try to correct the interference by one or more of the  
following measures:  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and  
receiver.  
– Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV  
technician for help.  
When the product is used on a cart, care  
should be taken to avoid quick stops,  
excessive force, and uneven surfaces  
which may cause the product and cart to  
overturn, damaging equipment or  
causing possible injury to the operator.  
Slots and openings in the cabinet are provided for  
ventilation. These ensure reliable operation of the  
product and protect it from overheating. These openings  
must not be blocked or covered. (The openings should  
never be blocked by placing the product on bed, sofa,  
rug, or similar surface. It should not be placed in a built-in  
installation such as a bookcase or rack unless proper  
ventilation is provided and the manufacturer’s  
About burning-in of the D-ILA device  
Do not allow the same still picture to be projected for a long  
time or an abnormally bright video picture to be projected.  
Do not project video images with high-intensity or high-  
contrast on a screen. The video image could be burned in to  
the D-ILA device.  
Use special care when projecting video games or computer  
program images. There is no problem with ordinary  
video-cassette playback images.  
instructions have been adhered to.)  
For proper ventilation, separate the product from other  
equipment, which may prevent ventilation and keep /  
distance more than 23-5/8" (60 cm).  
About the installation place  
Do not install the projector in a place that cannot support its  
weight securely.  
If the installation place is not sturdy enough, the projector  
could fall or overturn, possibly causing personal injury.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
This product should be operated only with the type of  
power source indicated on the label. If you are not sure  
of the type of power supply to your home, consult your  
product dealer or local power company.  
When connecting other products such as VCR’s, and  
personal computers, you should turn off the power of this  
product for protection against electric shock.  
Do not place combustibles behind the cooling fan. For  
example, cloth, paper, matches, aerosol cans or gas  
lighters that present special hazards when over heated.  
This product is equipped with a three-wire plug. This  
plug will fit only into a grounded power outlet. If you are  
unable to insert the plug into the outlet, contact your  
electrician to install the proper outlet. Do not defeat the  
safety purpose of the grounded plug.  
Do not look into the projection lens while the illumination  
lamp is turned on. Exposure of your eyes to the strong  
light can result in impaired eyesight.  
Power-supply cords should be routed so that they are not  
likely to be walked on or pinched by items placed upon or  
against them. Pay particular attention to cords at doors,  
plugs, receptacles, and the point where they exit from the  
product.  
Do not look into the inside of this unit through vents  
(ventilation holes), etc. Do not look at the illumination  
lamp directly by opening the cabinet while the  
illumination lamp is turned on. The illumination lamp also  
contains ultraviolet rays and the light is so powerful that  
your eyesight can be impaired.  
For added protection of this product during a lightning  
storm, or when it is left unattended and unused for long  
periods of time, unplug it from the wall outlet and  
disconnect the cable system. This will prevent damage  
to the product due to lightning and power line surges.  
Do not drop, hit, or damage the light-source lamp (lamp  
unit) in any way. It may cause the light-source lamp to  
break and lead to injuries. Do not use a damaged light-  
source lamp. If the light-source lamp is broken, ask your  
dealer to repair it. Fragments from a broken light-source  
lamp may cause injures.  
Do not overload wall outlets, extension cords, or  
convenience receptacles on other equipment as this can  
result in a risk of fire or electric shock.  
Xenon gas is enclosed with high pressure inside the light-  
source lamp (lamp unit) of this projector. If you drop or  
impart a shock to the lamp, or discard it as is, there is the  
possibility of explosion, leading to personal injury. Use  
special care when handling the lamp. For any unclear  
points, consult your product dealer.  
Never push objects of any kind into this product through  
openings as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the product.  
Do not attempt to service this product yourself as  
opening or removing covers may expose you to  
dangerous voltages and other hazards. Refer all service  
to qualified service personnel.  
Do not “ceiling-mount” the projector to a place which  
tends to vibrate; otherwise, the attaching fixture of the  
projector could be broken by the vibration, possibly  
causing it to fall or overturn, which could lead to personal  
injury.  
Unplug this product from the wall outlet and refer service  
to qualified service personnel under the following  
conditions:  
Use only the accessory cord designed for this product to  
prevent shock.  
a) When the power supply cord or plug is damaged.  
The power supply voltage rating of this product is  
AC 120 V, the power cord attached conforms to the  
following power supply voltage. Use only the power cord  
designated by our dealer to ensure Safety and EMC.  
b) If liquid has been spilled, or objects have fallen on the  
product.  
c) If the product has been exposed to rain or water.  
d) If the product does not operate normally by following  
the operating instructions. Adjust only those controls  
that are covered by the Operation Manual, as an  
improper adjustment of controls may result in damage  
and will often require extensive work by a qualified  
technician to restore the product to normal operation.  
When it is used by other power supply voltage, power  
cable must be changed.  
Ensure that the power cable used for the projector is the  
correct type for the AC outlet in your country.  
Consult your product dealer.  
e) If the product has been dropped or damaged in any  
way.  
Power cord  
f ) When the product exhibits a distinct change in  
performance – this indicates a need for service.  
When replacement parts are required, be sure the  
service technician has used replacement parts specified  
by the manufacturer or with same characteristics as the  
original part. Unauthorized substitutions may result in  
fire, electric shock, or other hazards.  
Power supply voltage: AC 120 V  
*DO NOT allow any unqualified person to  
install the unit.  
Be sure to ask your dealer to install the unit (eg.  
attaching it to the ceilling) since special technical  
knowledge and skills are required for installation.  
If installation is performed by an unqualified person, it  
may cause personal injury or electrical shock.  
Upon completion of any service or repairs to this product,  
ask the service technician to perform safety checks to  
determine that the product is in proper operating  
condition.  
The product should be placed more than one foot away  
from heat sources such as radiators, heat registers,  
stoves, and other products (including amplifiers) that  
produce heat.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
SAFETY PRECAUTIONS ................. 2  
Contents........................................... 4  
Accessories ..................................... 5  
Controls and Features .................... 6  
Front Side / Top Surface / Right Side .....................6  
Left-hand Side / Rear Side......................................7  
Bottom Surface .......................................................8  
Control Panel on the Projector................................9  
Connector Panel ...................................................11  
Remote Control Unit..............................................12  
Installing Batteries.................................................14  
Precautions for using batteries..............................14  
Setting for Watching Image Software  
(Video Menu Mode Only) ..................................... 47  
Adjusting Picture Quality ...................................... 48  
Adjusting Color temperature................................. 49  
Adjusting the Video Screen/Menu Position .......... 50  
Changing the Image Gamma/Aspect Ratio  
(Video Menu Mode Only) ..................................... 51  
Changing the Image Size - Resize Function  
(PC Menu Mode Only).......................................... 52  
Changing the Clamp pulse position  
(PC Menu Mode Only).......................................... 52  
Setting and Adjusting Other Functions  
(OPTIONS)........................................................... 53  
Getting Information............................................... 55  
Installing the Projector.................. 15  
Precautions for Installation....................................15  
Adjusting the Inclination of the Projector...............16  
Installing the Projector against the Screen............17  
Projection Distance and Screen Size....................18  
Setting the Amount of Lens Shifting......................19  
Effective Range and Distance of the  
Replacing the Fuse........................56  
Replacing the Light-Source  
Lamp ...............................................57  
Cleaning and Replacing the  
Filter Cover.....................................62  
Troubleshooting.............................63  
Warning Indication.........................65  
Warning Messages ........................66  
Specifications.................................69  
Outside dimensions.............................................. 71  
Pin assignment (Specifications for terminals) ...... 72  
Remote Control Unit..............................................20  
Setting the Position Selecting Screw for Ceiling  
Mounting ...............................................................21  
When installing (adjusting/setting) the unit............21  
Connecting to Various Devices.... 22  
Signals that Can Be Input to the Projector............22  
Connecting to Video Devices................................24  
Connecting to HDTV Devices/DVD Players ..........25  
RS-232C external control ..............73  
Appendix.........................................75  
Connecting to Devices which Control the  
Projector................................................................26  
Connecting to Computer Devices .........................27  
Connecting to DVI.................................................28  
How to attach the ferrite core................................28  
Connecting the Power Cord..................................29  
Removing the Lens Cap........................................29  
Basic Operations........................... 30  
1. Turning on the Power........................................31  
2. Select the Input source to be Projected ............32  
3. Adjust the Screen Size (Zooming) ....................33  
4. Adjust Focus .....................................................33  
5. Setting the Screen Aspect Ratio .......................33  
Turning off Image (HIDE)......................................34  
Removing the Trapezoidal Distortion of the  
Image ....................................................................34  
Quick Alignment Function (QUICK ALIGN.)..........35  
Displaying a Still Picture (FREEZE)......................36  
Zooming a Part of the Image  
(DIGITAL ZOOM T/W) ..........................................36  
Menu Operations ........................... 37  
Basic Menu Operation...........................................42  
Changing the Color System  
(Video Menu Mode Only) ......................................44  
Changing the Language Display...........................45  
Changing the Screen aspect ratio/HDTV format  
(Video Menu Mode Only) ......................................45  
Adjusting Tracking/Phase .....................................46  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
The following accessories are included with this projector. Check for them; if any item is missing, please  
contact your dealer.  
Remote control unit (RM-M160G)  
Personal computer connection cable  
[approx. 6.56 ft (approx. 2 m)]  
(D-sub, 3-row 15 pin)  
P l u s o n e D V I , 9 f t.  
Video cable  
[approx. 6.56 ft (approx. 2 m)]  
AA/R6-size dry cell battery (×2)  
(for checking operation)  
Conversion adapter for Mac  
(for Macintosh)  
Power cord  
[approx. 8.2 ft (approx. 2.5 m)]  
Ferrite core (×2)  
BNC-RCA Conversion plug  
Hex. wrench  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                 
Controls and Features  
Front Side / Top Surface / Right Side  
R
E
T
N
E
U N  
E O D  
E
M
I
V
C
P
T
I
X E  
E
T
A R E P  
O
E T S  
E
N
E
R
P
O
T
E
D
S
P
M
H I  
Y E  
E
T
K
P
M
A
L
W N  
O
D
P
U
1
9
8
7
Cabinet Design  
Subject to Change without notice.  
6
5 4  
3 2  
1 Exhaust vents  
6 Adjustable feet (for adjusting the height and  
Vents for cooling fans through which warm air comes out.  
angle)  
By extending the feet, the projector angle can be  
adjusted up to +7°.  
CAUTION  
For details, refer to “Adjusting the Inclination of the  
Projector” on page 16.  
• Do not block the exhaust vents, or heat will build up inside,  
possibly causing a fire. Also, do not touch the vents, or this  
could give you a low-temperature burn.  
7 Lens  
One of the optional lens units should be installed before  
using the projector.  
A lens-hole blind cover (black one) is installed when the  
projector is shipped from the factory.  
For details on the types of optional lenses available, refer  
to page 18.  
2 Carrying handle  
Raise this handle when carrying the projector.  
CAUTIONS  
• When carrying the projector, do not transmit shocks to it.  
Also be careful to keep it balanced.  
• Do not carry it while the light-source lamp is on or the  
CAUTION  
cooling fan is operating. This could cause personal injury.  
• Please consult your authorized dealer or service center for  
information about attaching an optional lens.  
3 AC IN (power input) terminal  
This is the power input terminal where the supplied  
power cord is connected. For details, refer to page 30.  
8 Lens cap  
This is the lens cap provided for the optional lens.  
When you are not using the projector, attach the lens cap  
to protect the lens from dirt or being damaged. (Refer to  
page 30.)  
4 Fuse holder  
A fuse rated 12A/250V is installed. (Power source  
protection)  
To replace the fuse, refer to page 57.  
9 Remote sensor  
When operating with the remote control, aim it toward  
this sensor. (Refer to page 20.)  
CAUTION  
• When replacing the fuse, use the same rating and type.  
Otherwise, a fire may occur and/or the projector may be  
damaged.  
5 MAIN POWER switch  
This is the main power switch. When it is turned on, the  
projector goes into stand-by state, and the STAND BY  
indicator on the control panel comes on. (Refer to  
page 32.)  
ON [ | ]: The main power turns on.  
OFF []: The main power turns off.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
Left-hand Side / Rear Side  
p Connector panel  
For details, refer to “Connector Panel” on page 11.  
q Rear adjustable foot (for leveling the projector)  
It is set at the shortest position when shipped from the  
factory. Turn the foot to make the projector level.  
Adjustment can be made in the range of +1.5° and –1.5°  
from the horizontal position. For details, refer to  
“Adjusting the Inclination of the Projector” on page 16.  
w Air inlet  
This is the air inlet. Do not cover or obstruct this slot.  
e Control panel  
For details, refer to “Control Panel on the Projector” on  
page 9.  
r Lens shift knob cap  
When you have mounted a lens that uses the lens shift  
function, open this cap and rotate the lens shift knob to  
move the lens position. For more information, refer to  
“Setting the Amount of Lens Shifting” on page 19.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
Bottom Surface  
t
y
u
i
t Air inlet (filter)  
Air is taken in through the filter to cool the light-source  
lamp. If the filter is blocked or if something that obstructs  
the flow of air is placed around the projector, heat may  
build up inside and could cause a fire. For required  
space, refer to “Precautions for Installation” on page 15.  
CAUTIONS  
• Be careful as paper, cloth or soft cushion could be drawn in  
if placed nearby. Do not block the filter, or heat may build  
up and could cause a fire.  
• Clean the filter periodically. For details, refer to “Cleaning  
and Replacing the Filter Cover” on page 63. Deposition of  
dirt on the filter reduces the cooling effect, causing heat to  
build up inside, which could cause a fire or malfunction.  
y Opening for replacing the light-source lamp  
For replacing the light-source lamp, refer to “Replacing  
the Light-Source Lamp” on page 58.  
u Fixing foot  
i Position selecting screw for ceiling mounting  
When using the projector in an upside-down, ceiling-  
mounted position (inverted top-to-bottom and right-to-  
left), the “position selecting screw for ceiling mounting”  
must be turned to switch to ceiling mounting.  
This will correct variance in color images (shading),  
which otherwise would occur in ceiling mounting.  
For more information, refer to “Setting the Position  
Selecting Screw for Ceiling Mounting” on page 21.  
CAUTION  
• To ceiling-mount and adjust the projector, special expertise  
and technique are necessary. Be sure to ask your dealer or  
specialist to perform this work.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
Control Panel on the Projector  
r
e
1
STAND BY  
OPERATE  
LAMP  
TEMP  
2
3
HIDE  
w
q
PC  
4
5
KEYSTONE  
PRESET  
VIDEO  
MENU  
6
7
p
9
8
EXIT  
ENTER  
1 STAND BY Indicator  
Memo  
ON :  
When in stand-by mode.  
While in the cool-down mode (STAND BY indicator is blinking):  
Even if you press the OPERATE button, the projector is not  
turned on. Wait until the projector enters stand-by mode  
(STAND BY indicator stays lit).  
Blinking :When in cool-down mode.  
Memo  
About the cool-down mode:  
4 PC button  
This projector has a function to cool down the heated lamp for a  
fixed period of time (approx. 120 seconds) after projection is  
finished. This feature is referred to as the cool-down mode.  
The purpose of the cool-down mode is to prevent inner parts  
from being deformed or broken by heat from the heated lamp  
as well as to prolong the life of the lamp.  
Use this button to select a device connected to the PC 1,  
PC 2 or DVI terminals. Each time you press the button,  
the selection alternates among PC 1, PC 2 and DVI.  
* “PC1” , “PC2” or “DVI” will be displayed on the top right of  
the projected image. (This function can be disabled by  
the menu.)  
CAUTIONS  
5 VIDEO button  
Use this button to select a device such as a video deck  
connected to the AV IN (Y/C, VIDEO or COMP) terminal  
of the projector. Each time you press the button, the  
selection alternates among Y/C, VIDEO and COMP.  
* “Y/C”, “VIDEO” or “COMP” will be displayed on the top right of  
the projected image. (This function can be disabled by the  
menu.)  
• Do not turn off the MAIN POWER switch while in the cool-  
down mode.  
• Do not place the projector on its side or stand it upright  
while in the cool-down mode; this may block the vents.  
2 OPERATE indicator  
ON : When the projector is in operation (projecting).  
OFF : When the projector is not in operation (not  
projecting).  
6 MENU button  
Use this button to enter or exit the menu mode. The main  
menu appears or disappears at the screen. For details,  
refer to “Basic Menu Operation” on page 43.  
3 OPERATE button  
When the projector is in the stand-by mode, press this  
button one second or more, and the projector is turned  
on, causing the OPERATE indicator to light.  
Press it one second or more again, and the projector  
goes into the cool-down mode, then stand-by mode.  
(Refer to page 32.)  
* You cannot use the OPERATE button for about one  
minute after the lamp blinks. Press the button after a  
minute or longer has elapsed.  
7 ENTER button  
This button will be used in the menu mode. Use to  
display the hierarchical menus. Also use when “ENTER”  
is displayed against the item on the menu screen or  
when the “All reset” selection is confirmed. For details,  
refer to “Basic Menu Operation” on page 43.  
8 Cursor buttons 5//2/3  
These buttons will be used in the menu mode to select an  
item, or to set or adjust the value. For details, refer to  
“Basic Menu Operation” on page 43.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
9 EXIT button  
This button will be used in the menu mode to return to the  
previous menu. When the main menu is displayed, this  
button will cause the menu to disappear. For details, refer  
to “Basic Menu Operation” on page 43.  
p PRESET button  
This PRESET button only works as a reset button for the  
direct button adjustment of the KEYSTONE button of the  
control panel and the DIGITAL ZOOM button of the  
remote control. When adjusting the keystone or digital  
zoom (when the setting is displayed on the screen) the  
adjusted value is reset to that which was set when the  
projector was shipped from the factory. Of the menu  
items, this button only works for the keystone setting  
screen.  
q KEYSTONE  
/
buttons  
Use these buttons to correct a trapezoidal distortion of  
the projected image. (Refer to page 35.)  
w HIDE button  
Use this button to turn off the image on the screen  
temporarily. Pressing it again restores the image to  
resume. (Refer to page 35.)  
e LAMP indicator  
ON :  
After the light-source lamp has been used for  
more than approx. 900 hours. (NORMAL only)  
Blinking : After the light-source lamp has been used for  
more than approx. 1000 hours (1900 hours in the  
LPC or LOC mode). Replace the light-source  
lamp. Refer to “Replacing the Light-Source  
Lamp” on page 58 or page 59.  
r TEMP indicator  
Blinking : The temperature inside the projector has risen  
abnormally.  
Note  
• While the TEMP indicator is blinking (during abnormal  
temperature), the power is automatically cut off.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
Connector Panel  
4
5
R
Y
1
2
Y/C  
6
7
8
G
B
H
V
P
B/B-Y  
R/R-Y  
VIDEO  
P
REMOTE  
IN  
3
9
IN  
OUT  
1 PC (computer) 1 input terminal (D-sub 3-row 15  
5 Component terminal  
Component signals (Y, B-Y, R-Y) or DTV-format (Y, PB,  
PR) signals. (Devices which have component output  
terminals can be connected.)  
pin)  
This is an input terminal dedicated to computer signals  
(RGB video signals and sync signals).  
* Connect 480i/480p Component sources to Video Processor,  
YPrPb HDTV sources can connect directly here.  
Connect the display output terminal of the computer to  
this terminal. When a Macintosh computer is to be  
connected, use the supplied conversion adapter for Mac.  
6 Y/C (S-video) input terminal (Mini DIN 4 pin)  
Connect S-video sources to the Video Processor.  
Note  
• When computer-related signals are input, the uppermost  
edge of the image may appear to bow if the sync signal  
input is composite sync (Cs) or G on sync signal. In this  
case, use separate sync signals for vertical sync (V) and  
horizontal sync (H).  
7
VIDEO (composite video) input terminal (BNC)  
Connect Video to the Video Processor.  
2 PC (computer) OUT terminal (D-sub 3-row 15 pin)  
This is the terminal for video output from the monitor of  
the computer connected to PC1 or PC2.  
8 REMOTE terminal (stereo mini jack)  
Connect an infrared remote control extension unit, etc. to  
this jack.  
Attach the ferrite core (accessory) to the cable which is  
connected to the REMOTE terminal. (Refer to page 29.)  
* For details, consult your dealer.  
The computer input signal projected on the screen is  
output. A display monitor can be used by connecting it to  
this terminal.  
3 DVI terminal [DVI-D 24 pin]  
This is the digital RGBHV input terminal.  
• Connect Video Processor here.  
9 RS-232C CONTROL terminal IN/OUT (D-sub 9 pin)  
This is the RS-232C interface-specified terminal. The  
projector can be controlled by a computer connected  
externally.  
4 PC (computer) 2 input terminals (BNC × 5)  
These are multipurpose video input terminals that allow  
input of the following signals.  
* For details, refer to page 27 and 74.  
• Analog RGB signals, vertical sync (V) signals, and  
horizontal sync (H) signals / composite signals (Cs).  
(Devices which have analog RGB signal output  
terminals can be connected.)  
* Input of external sync signals is automatically detected.  
Detection of H/V signals or Cs signals causes automatic  
switching to external sync. The priority order is H/V > Cs.  
Note  
• When computer-related signals are input, the uppermost  
edge of the image may appear to bow if the sync signal  
input is composite sync (Cs) or G on sync signal. In this  
case, use separate sync signals for vertical sync (V) and  
horizontal sync (H).  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
Remote Control Unit  
On the remote control, the same buttons as on the control  
panel of the projector are provided except for the following  
buttons. For the same buttons, operation is the same in  
principle.  
5 VIDEO button  
Use this button to select a device such as a video deck  
connected to the AV IN terminal (VIDEO, Y/C or COMP  
input terminal) of the projector. Each time you press the  
button, the selection alternates among Y/C, VIDEO and  
DVI. (Refer to page 33.)  
* “Y/C”, “VIDEO” or “DVI” will be displayed on the top right  
of the projected image. (This function can be disabled by  
the menu.)  
For remote control only:  
DIGITAL ZOOM T/W, QUICK ALIGN., FREEZE, ZOOM T/  
W, FOCUS +/–, SCREEN W/S, PC 1, PC 2, VIDEO, Y/C,  
DVI, COMP. See insert for instructions on Learning Remote.  
1
6 ZOOM T/W buttons  
Use these buttons to adjust the projected screen size.  
T (Tele): The projected screen size decreases.  
W (Wide):The projected screen size increases.  
QUICK  
OPERATE  
ALIGN.  
7 FOCUS +/– buttons  
u
y
t
2
HIDE  
Use these buttons to adjust the focus of the projected  
video image.  
+ : The focus point becomes more distant.  
– : The focus point becomes nearer.  
W
3
SCREEN FREEZE  
S
COMP  
DVI  
VIDEO  
Y/C  
4
6
PC1  
PC2  
5
7
8
r
T
T
ZOOM  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
e
w
W
W
8 MENU button  
PRESET  
Use this button to enter or exit the menu mode. The main  
menu appears or disappears at the screen. For details,  
refer to “Basic Menu Operation” on page 43.  
9
p
q
EXIT  
ENTER  
9 Cursor buttons 5//2/3  
These buttons are used in the menu mode to select an  
item or to set or adjust the value. For details, refer to  
“Basic Menu Operation” on page 43.  
RM-M160 REMOTE CONTROL UNIT  
p ENTER button  
1 Remote control’s signal transmitter  
This button is used in the menu mode. Use to display the  
hierarchical menus. Also use when “ENTER” is displayed  
against the item on the menu screen or when the “All  
reset” selection is confirmed. For details, refer to “Basic  
Menu Operation” on page 43.  
2 OPERATE button  
When the projector is in the stand-by mode, press this  
button one second or more, and the projector is turned  
on, causing the OPERATE indicator to light.  
Press it one second or more again, and the projector  
goes into the cool-down mode, then stand-by mode.  
(Refer to page 32.)  
* The OPERATE button will not work for approximately 1  
minute from when the light-source lamp is turned on. Use  
the button after approximately 1 minute.  
q EXIT button  
This button is used in the menu mode to return to the  
previous menu. When the main menu is displayed, this  
button will cause the menu to disappear. For details, refer  
to “Basic Menu Operation” on page 43.  
w PRESET button  
This PRESET button only works as a reset button for the  
direct button adjustment of the KEYSTONE button of the  
control panel and the DIGITAL ZOOM button of the  
remote control. When adjusting the keystone or digital  
zoom (when the setting is displayed on the screen) the  
adjusted value is reset to that which was set when the  
projector was shipped from the factory. Of the menu  
items, this button only works for the keystone setting  
screen.  
Memo  
While in the cool-down mode (STAND BY indicator is  
blinking):  
Even if you press the OPERATE button, the projector is not  
turned on. Wait until the projector enters stand-by mode  
(STAND BY indicator stays lit).  
3 HIDE button  
Use this button to turn off the image on the screen  
temporarily. Pressing it again makes the image to  
resume. (Refer to page 35.)  
e KEYSTONE  
/
buttons  
Use these buttons to correct a trapezoidal distortion of  
the projected image. (Refer to page 35.)  
4 FREEZE button  
During projection of an image on the screen, press this  
button to obtain a still picture.  
To restore normal projection, press it again. (Refer to  
page 37.)  
* Depending on the video signal source (UXGA, etc.), this  
button does not work.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
r DIGITAL ZOOM T/W buttons  
A part of image can be magnified up to four times on the  
screen.  
Each time the T or W button is pressed, the image is  
enlarged or the enlarged image is reduced by a certain  
degree. (Refer to page 37.)  
* Images which are enlarged with the digital zoom become  
less clear.  
* Depending on the video signal source (UXGA, etc.), this  
button does not work.  
t PC buttons  
Use these buttons to select a device connected to the PC  
1, PC 2 or DVI terminals. (Refer to page 33.)  
* “PC 1”, “PC 2” or “DVI” will be displayed on the top right  
of the projected image. (This function can be disabled  
using the menu.)  
y SCREEN W/S buttons  
Changes the projection screen size to [4:3] or [16:9].  
u QUICK ALIGN. (Quick Alignment) button  
Use this button to automatically align “Horizontal and  
vertical position”, “Tracking” and “Phase” for the  
projected image.  
During the automatic alignment, “Quick Alignment”  
appears on the screen, and disappears after alignment is  
finished. (Refer to page 36.)  
* The “Quick Alignment” function only works when the  
signal is input from the input terminal of PC 1, PC 2 or  
DVI. It does not work when the signal is input from the  
VIDEO IN terminal (VIDEO, Y/C and COMP. input  
terminal).  
CAUTION  
• Automatic alignment with the quick alignment function  
should be carried out on a bright still-picture. This function  
may not work correctly on a dark picture or motion-picture.  
If adjustment with this function is not satisfactory, adjust  
“Horizontal and vertical position”, “Tracking” and “Phase” in  
the menu mode.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and Features  
Installing Batteries  
Install batteries in the remote control. If the remote control has started to work erratically, replace the  
batteries.  
1 Open the back cover.  
Precautions for using batteries  
Open the back cover in the direction of the arrow.  
If batteries are used incorrectly, they may crack or  
leak liquid. This could cause a fire, burn, malfunction,  
or staining or damaging of the surroundings.  
Beware of the following:  
• Do not mix new and old batteries.  
• Do not mix different types of batteries as they differ in  
characteristics.  
• Place batteries so they match the polarities indicated:  
(+) to (+) and (–) to (–).  
• Be sure to put the minus (–) end in first to avoid  
short-circulating.  
• Use only designated batteries.  
• Remove the batteries if the remote is not to be used for a  
2 Install the batteries.  
prolonged period.  
Place the two supplied batteries (AA/R6-size) in the  
• When the batteries are exhausted, replace them  
remote control as illustrated below.  
immediately. Otherwise, liquid could leak, or malfunction  
could occur due to leaking liquid. If the leaked liquid  
contacts the skin, wipe it off with a cloth, otherwise the skin  
could become rough.  
• Do not put batteries into a fire or try to recharge them.  
• Batteries run for six months to one year in normal use.  
However, the batteries supplied are for confirming  
operation and may not run that long. When the remote  
control starts failing to work properly, replace the batteries  
with new ones.  
3 Close the back cover.  
First fit the claws on the back cover in the case, then  
close the back cover in the direction of the arrow.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Projector  
Precautions for Installation  
CAUTIONS  
1. Before installation, do not connect the projector’s power cord.  
2. Do not install the projector in the following places:  
• Where there is water, humidity or dust.  
• Where the projector may be subjected to oil, smoke or cigarette smoke.  
• On a soft surface such as a carpet or cushion.  
• Where the projector may be subjected to direct sunlight.  
• Where temperature is high or humidity is low.  
Allowable operation temperature range: 41°F to 95°F (+5°C to +35°C)  
Allowable relative humidity range: 20% to 80% (no condensation)  
Allowable storage temperature range: 14°F to 140°F (–10°C to +60°C)  
When installing the projector, observe the following:  
• Do not use the projector placed on its side.  
Avoid using the projector placed on its side. This could cause a malfunction.  
• Use the projector within the specified angle.  
Do not use the projector inclined 30° horizontally (left/right). This could cause color variation or shorten the lamp life.  
• Do not block the exhaust vents.  
Do not use a cover which encloses the projector air-tight or blocks the exhaust vents. Allow sufficient space around the  
projector. When the projector is enclosed in a space of the following dimensions, use an air conditioner so the temperature  
inside becomes equal to the outside temperature.  
Allowable minimum space required  
300mm  
200mm  
600mm  
300mm  
200mm  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Projector  
Adjusting the Inclination of the Projector  
The vertical angle and the leveling of the projector can be adjusted with the adjustable feet at the bottom of the projector.  
Adjusting the vertical angle of the projector  
While pushing the levers on both sides upward, raise the projector. The adjustable feet automatically extend.  
To retract the feet, push the levers and lower the projector slowly; the projector is fixed at the position  
where you release the levers.  
lever  
Adjustable feet (at the front)  
Leveling the projector  
Lift the projector, rotate the rear adjustable foot, and adjust the horizontal angle until the projector is level.  
Adjustable foot (at the rear)  
Fixing foot (at the rear)  
Extend  
Shorten  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Projector  
Installing the Projector against the Screen  
The projector should be placed so that the center line of the lens is at a right angle to the screen as shown in the following  
figures.  
Side view  
Top view  
Trapezoidal-distortion correctable maximum angle  
The projector has a function to correct the trapezoidal distortion of the projected image on the screen.  
To correct this distortion, use the KEYSTONE buttons on the projector. (Refer to “Removing the Trapezoidal Distortion of the  
Image” on page 35.) Also, correction is possible by using the “Keystone” menu. (Refer to “Setting and Adjusting Other  
Functions (OPTIONS)” on page 54.)  
Correctable angle:  
Correctable angle:  
Up to approx. 20° downward from the horizontal line  
Up to approx. 20° upward from the horizontal line  
Note: There is a 7% drop (for ceiling mount) using the anamorphic lens. Calculate 7% of the throw distance.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Projector  
Projection Distance and Screen Size  
• The range of projection distances that can be focused depends on the lens unit (optional) to be used. When the aspect ratio  
of the screen is 4:3, the range is as follows and you need to install the projector within this range.  
Lens type  
Approximate projection distance  
0.77 m to 4.03 m  
1.76 m to 4.50 m  
2.77 m to 19.71 m  
4.74 m to 29.87 m  
GL-M2910G  
GL-M2915SG  
GL-M2920ZG  
GL-M2930SZG  
Note: There is a 7% drop (for ceiling mount) using the  
anamorpich lens. Calculate 7% of the throw distance.  
*: The value for projection distance is a guide (reference) one. The projected image size may vary depending on the  
manufacturing tolerance of the projection lens.  
Change of projection screen  
according to aspect ratio  
Screen  
Screen with 4:3 aspect ratio  
Screen with 16:9 aspect ratio  
90˚  
90˚  
90˚  
Center line of the lens  
To move the Shift position by 50%, set the bottom edge of the projec-  
tion screen so that it is at the same height as the center of the lens.  
Notes  
• For detailed relationship between projection distances and projection screen sizes, refer to Appendix A. The relationships for  
both 4:3 and 16:9 ratios are listed there.  
• When installing a screen, use a 4:3 aspect-ratio picture.  
• (A 16 : 9 aspect-ratio picture is projected based on the width of the range in which a 4:3 aspect-ratio picture is projected.)  
• The diagonal length of a 16:9 aspect-ratio screen is about 91.8% that of a 4:3 aspect-ratio screen. This value is only a guide  
(reference).  
• If sunlight or lamp light strikes the projection screen directly, the picture tends to become pale and dim. Use a curtain or  
other means to shield the light.  
• Set the projector horizontally on a surface that is within the range of adjustable angles (up/down adjustment angle: +7° ;  
horizontal adjustment angle: 1.5°).  
• If the keystone is adjusted, the projected screen becomes smaller.  
• When hanging from the ceiling, use a dedicated hanging fixture (not supplied).  
Optional Lenses  
This projector does not include a lens. You can select one of the optional lenses to adjust the projection distance. Please ask  
your authorized dealer or service center to install the lens.  
Lens model  
Function  
GL-M2910G  
Powered focus for rear projection, short focal length (subject ratio 1:1), 0% influence.  
Powered focus, short focal length (subject ratio 1.5:1), powered image adjustment (2%  
zoom), includes manual vertical shift function, 30%-55% influence  
GL-M2915SG  
GL-M2920ZG  
GL-M2930SZG  
Powered zoom/powered focus lens (subject ratio 2:1-3:1), 50% influence.  
Powered zoom/powered focus long focal length lens (subject ratio 2.9:1-5.5:1), includes  
manual vertical shift function, 30%-55% influence.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Projector  
Setting the Amount of Lens Shifting  
When the lens unit (optional) with the lens shifting function is used, the projected screen can be shifted up and down in  
position.  
Notes  
• The amount of shifting is within the range of approx. 30% to 55%.  
• After finishing the lens shift setting, tighten the SHIFT LOCK fixing bolt firmly so that the lens will not move.  
1 Turn the cap on the top of the projector to open it.  
2 Loosen the SHIFT LOCK fixing bolt.  
Use the hex. wrench supplied.  
3 Rotate the LENS SHIFT knob to adjust the position (shift amount) of the projected  
screen.  
Rotate it to the right: The lens shifts upward.  
Rotate it to the left: The lens shifts downward.  
4 Tighten the SHIFT LOCK fixing bolt firmly.  
Use the hex. wrench supplied.  
5 Turn the cap to close it.  
SHIFT LOCK fixing bolt  
LENS SHIFT knob  
Projected screen position image by amount of shift  
* The projected screen position can only shift in an up-and-down direction.  
The illustration shows the screen shifted sidewise for the purpose of explanation.  
Approx. 55%  
Approx. 50%  
Approx. 30%  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Projector  
Effective Range and Distance of the Remote Control Unit  
The remote control unit can be used as either a wireless remote control unit or a wired one.  
Using as a wireless remote control unit  
Aim the remote control unit toward the remote sensor on the front or the rear of the projector.  
The operable distance of the remote control unit is about 10 m for direct reception. The remote control unit can be used by  
having it reflected on the screen. In this case, the total distance of “A+B” should be about 10 m or less. The operable angles  
of the remote control unit are 15° right and left, and 15° up and down.  
Screen  
15˚  
15˚  
Projector  
15˚  
A
15˚  
B
Remote control unit  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the Projector  
Setting the Position Selecting Screw for Ceiling Mounting  
When using the projector in an upside-down, ceiling-mounted position (inverted top-to-bottom and right-to-left), the “position  
selecting screw for ceiling mounting” must be turned to switch to ceiling mounting.  
This will correct variance in color images (shading), which otherwise would occur in ceiling mounting.  
To revert to normal desktop setting, turn the “position selecting screw for ceiling mounting” back to the initial position (factory-  
shipped).  
When using the projector in an upside-down, ceiling-mounted position:  
Turn the “position selecting screw for ceiling mounting” fully counterclockwise (until it is turning idly).  
To again use the projector in a normal desktop setting:  
Turn the “position selecting screw for ceiling mounting” fully clockwise (until it firmly tightens).  
For normal desktop mounting:  
Turn the screw clockwise.  
For upside-down, ceiling-mounting:  
Turn the screw counterclockwise.  
CAUTIONS  
To ceiling-mount and adjust the projector, special expertise and technique are  
necessary. Be sure to ask your dealer or a specialist to perform this work.  
To turn the “position selecting screw for ceiling mounting”, use a Phillips  
screwdriver with a 30-mm or longer shank.  
The screw is located in the hole shown in the illustration.  
Position selecting screw for ceiling mounting  
Note  
• When using the projector in a ceiling-mounted position, you should reverse the projected image by changing the settings of  
Right Left rev. and Top Bottom inv. menus. For details, refer to page 54. You can also change these settings without  
receiving a video signal. In this case, refer to “Menu Transition Diagram in No signal Menu Mode” on page 38.  
When installing (adjusting/setting) the unit  
• When using “Top Bottom inv.” on the “Options” menu, reset the unit by following the procedure below.  
• This reset procedure must be performed before operating the unit.  
1. Change the “Top Bottom inv.” Setting on the “Options” menu.  
2. Press the OPERATE button to enter the unit into the stand-by mode.  
3. Press the OPERATE button again to turn on the unit.  
• Adjust the focus after projecting a picture for 30 minutes or longer.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Before connection, be sure to turn off the projector and connected devices.  
Read the manual which comes with each device thoroughly.  
Signals that Can Be Input to the Projector  
The following signals can be input to the projector:  
Note: Instructions for installing the Video  
Video signals  
Processor begin on page 24.  
(1) Response to color systems  
Color systems  
NTSC  
NTSC4.43  
PAL  
SECAM  
Input terminal  
VIDEO  
- - - - -  
*2  
*1  
*2  
*2  
Y/C  
Y, PB/B-Y, PR/R-Y  
G, B, R, H/CS, V  
*2  
*2  
*2  
*2  
*2  
*1:Responds if Y/C output is available.  
*2:Signifies that component signals (“Y, PB, PR” / “Y, B-Y, R-Y” / “G, B, R, H/CS, V”) conform to the signal timing  
(synchronization and video period) of each color system. The color systems are used for convenience only.  
(2) Response to double density (*3), high-vision signals  
NTSC*4  
NTSC*5  
Input terminal  
Y, PB/B-Y, PR/R-Y  
G, B, R, H/CS, V  
High-vision signal  
*3:Signals whose density of scanning lines/field is twice as high.  
*4:Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line  
doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded  
wide-clear-vision signal and decoded 525P progressive signal.  
*5:Responds to signals whose horizontal scanning frequency is 33.5 kHz. PAL can be made twice as dense by a line doubler  
(separately available: recommended article).  
(3) Response to DTV-format signals  
DTV-format signals (480i, 480p, 720p, 1080i) can be input to the Y, PB/B-Y, PR/R-Y, G, B, R, H/CS, V input terminal.  
Computer signals  
Signals with the following scanning frequencies can be input to the PC 1 or PC 2 (G, B, R, H/CS, V) and DVI terminals.  
Horizontal scanning frequency  
Vertical scanning frequency  
15kHz - 105kHz  
50Hz - 100Hz  
Be sure that the computer to be used suffices the following conditions:  
• The computer has the video signal output port.  
Be sure that the computer has the video signal output port by reading the instruction book of the computer.  
The video signal output port is generally called as “RGB port”, “monitor port”, or “video port”. If the computer-monitor hybrid  
type or note type is used, it may need to prepare for an external output port. Also, there will be the type to which an external  
output port cannot be installed.  
• DVI input  
During DVI input, depending on the computer settings, there may be no signal input or an error may occur (blue screen).  
If this happens, turn off the power to both the projector and the computer, and then turn the projector back on before turning  
the computer on again. Then correctly set the computer's graphic board.  
• The resolution and the scanning frequencies are within the range specified in the table on page 23.  
Be sure that the resolution and the scanning frequencies of the video signal are within the range. A video signal out of range  
cannot be used. (Even signals out of the range could be projected. However, it may not sharp enough. On the other hand,  
even some of the signals within the range may require adjustment depending on the video board used.)  
When a signal other than listed in the table on page 23 is input, the image could be partially erased or an unneeded fold-over  
image could appear.  
Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.  
Composite sync (CS) and G on Sync signals cannot be handled depending on the devices connected.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Allowable input signals  
Horizontal res- Vertical resolu- Horizontal fre-  
Vertical fre-  
quency  
Signal  
olution  
tion  
quency  
Hor [Pixels]  
Ver [Lines]  
H [kHz]  
V [Hz]  
PC system  
PC98  
PC/AT  
DOS/V  
DVI*  
VESA350  
640  
350  
37.86  
84.13  
PC98  
640  
640  
400  
480  
24.83  
31.47  
37.86  
37.50  
43.27  
35.16  
37.88  
48.08  
46.88  
53.67  
35.52  
48.36  
56.48  
60.02  
68.68  
46.43  
63.98  
79.98  
91.15  
75.00  
35.00  
49.73  
60.24  
68.68  
33.75  
33.72  
31.47  
45.00  
44.96  
33.75  
33.72  
27.00  
15.734  
15.625  
15.625  
56.42  
59.94  
72.81  
75.00  
85.01  
56.25  
60.32  
72.19  
75.00  
85.06  
43.48  
60.00  
70.07  
75.03  
85.00  
43.44  
60.02  
75.03  
85.02  
60.00  
66.67  
74.55  
74.93  
75.06  
60.00  
59.94  
59.94  
60.00  
59.94  
60.00  
59.94  
24.00  
60  
VGA 60Hz*  
VGA 72Hz*  
VGA 75Hz*  
VGA 85Hz*  
SVGA 56Hz*  
SVGA 60Hz*  
SVGA 72Hz*  
SVGA 75Hz*  
SVGA 85Hz*  
XGA 43Hz*  
XGA 60Hz*  
XGA 70Hz*  
XGA 75Hz*  
XGA 85Hz*  
SXGA 43Hz*  
SXGA 60Hz*  
SXGA 75Hz*  
SXGA 85Hz*  
UXGA 60Hz  
MAC13  
640  
480  
640  
480  
640  
480  
800  
600  
800  
600  
800  
600  
800  
600  
800  
600  
1024  
1024  
1024  
1024  
1024  
1280  
1280  
1280  
1280  
1600  
640  
768/2  
768  
768  
768  
768  
1024/2  
1024  
1024  
1024  
1200  
480  
Mac  
MAC16  
832  
624  
MAC19  
1024  
1152  
768  
MAC21  
870  
Video system  
Video  
HDTV (1035i) 60Hz  
HDTV (1035i) 59Hz  
480p  
720  
1280  
1280  
1920  
1920  
1920  
483  
720  
720p 60Hz  
720p 59Hz  
1080i 60Hz  
1080i 59Hz  
1080 24sF  
NTSC  
720  
1080/2  
1080/2  
1080  
PAL  
50  
SECAM  
50  
* A signal that can be input by DVI (V-sync 85Hz is not supported.)  
Notes  
• The resolution for the input signals is listed in the above table.  
• Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.  
• When a signal other than listed above is input, the image could be partially erased or an unneeded fold-over image could  
appear.  
• Some signals other than listed above can be displayed. But they may require adjustment.  
• Even some of the signals listed above may require adjustment depending on the video board used.  
• Composite sync (CS) and G on Sync signals cannot be handled depending on the devices connected.  
• The VGA signal of the PC system could be displayed in 480p mode of the VIDEO system. (In this case, the projector enters  
video menu mode when the MENU button is pressed.)  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Connecting to Video Devices  
Before connection, be sure to turn off both the projector and video device.  
• Read thoroughly the manual that comes with each video device.  
• Use the supplied video cable. An video cable with an S-video (Y/C) terminal is not supplied.  
R
Y
Y/C  
G
P
B/B-Y  
R/R-Y  
VIDEO  
B
H
V
P
REMOTE  
IN  
IN  
OUT  
Video devices  
• VCR (Video cassette recorder)  
Video Processor  
• Laser videodisc player  
• Camcorder  
Notes  
• Connect a composite image signal output device or Y/C (S-video) image output device.  
• When connecting the S-video cable, refer to “How to attach the ferrite core” on page 29.  
Memo  
• When connecting a VHS device, using a TBC, or one which has one built-in, is recommended  
• Use of an extension cable to connect a video device and the projector could cause video degradation.  
• When a signal with much jitter is reproduced on a VCR, or special-effect playback is performed, the upper part of the image  
or the image itself may be erased or distorted.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Connecting to HDTV Devices/DVD Players  
Before connecting, be sure to turn off both the projector and HDTV devices/DVD players.  
• Thoroughly read the manual that comes with each HDTV device or DVD player.  
• Use separately available BNC cables to connect HDTV devices and DVD players.  
To Y  
To PC 2  
Y
Y/C  
To PB/B-Y  
H
V
P
B/B-Y  
R/R-Y  
To PR/R-Y  
VIDEO  
P
REMOTE  
Video Processor  
IN  
IN  
OUT  
BNC cable  
(separately available)  
HDTV devices  
DVD player  
HDTV sources can either be  
sent as pass-through via the  
video processor or connected  
directly to the projector.  
Note  
• Connect a component signal output device or DTV-format signal output device.  
Memo  
• Other devices with component signal output terminals (DVD player (NTSC), etc.) can be connected.  
(*DVD: Digital Video Disc)  
• DTV-format signals (480i, 480p, 720p, 1080i) can be input. For DTV-format signals which can be handled, refer to “Video  
signals” on page 22.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Connecting to Devices which Control the Projector  
Before connection, be sure to turn off both the projector and devices to be connected.  
• Read thoroughly the manual that comes with each device to be connected.  
• By connecting a computer to the RS-232C terminal, you can control the projector. Also, you can make an infrared remote  
sensor extension unit and connect it to the REMOTE terminal of the projector.  
* Obtain connection cables as required. Use a reverse connection cable.  
* For details, refer to “RS-232C external control” on page 74.  
* RS232 or IR control of the Video Processor is also required if controling the projector  
R
Y
Y/C  
G
P
B/B-Y  
R/R-Y  
VIDEO  
B
H
V
P
TO CONTROL  
REMOTE  
IN  
• Desktop type  
IN  
OUT  
*
To RS-232C connector  
To RS-232C connector  
Infrared remote sensor  
extension unit  
• Note type  
(Needs to be made)  
RS-232C reverse  
connection cable  
(separately available)  
* By directly connecting the OUT terminal  
to the second projector IN  
terminal, a number of  
To RS-232C connector  
units can be controlled by a single  
computer.  
Note  
• When connecting the cable to the REMOTE terminal, refer to “How to attach the ferrite core” on page 29.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Connecting to Computer Devices  
Before connection, be sure to turn off both the projector and computer devices.  
• Read thoroughly the manual that comes with each device.  
Connection to an IBM PC or IBM-compatible computer  
• Use the supplied personal computer connection cable. Also, prepare cables required for connecting the devices connected.  
Computer signals can either be connected directly to the projector or sent as pass-through to the Video Processor.  
• Desktop type  
To PC 1  
Personal Computer  
connection cable (supplied)  
To monitor  
connector  
To PC 2  
To R  
R
Y
To G  
To B  
To PC 1  
G
B
H
V
P
B/B-Y  
To PC OUT  
P
/R-Y  
• Notebook type  
Cable  
supplied  
To H/Cs  
To V  
with the  
display (or  
separately  
available)  
(D-sub 3-  
row 15-pin)  
IN  
* There are some notebook types which  
do not allow the computer’s LCD to work  
if an external display is connected. With  
such a notebook computer, the LCD  
display and external display output  
need to be switched.  
To PC 2  
IN  
To PC 2  
Separate cable (separately available)  
• Desktop type  
To monitor connector  
POWER  
Display monitor  
* When a display monitor is connected to  
the PC OUT terminal, you can view the  
video from the computer on the monitor.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Connecting to DVI  
Before connection, be sure to turn off both the projector and computer devices.  
• Read thoroughly the manual that comes with each device.  
R
Y
G
B
H
V
P
P
DVI (DVI-D 24pin Cable)  
Faroudja Video Processor  
IN  
IN  
Note  
• Other connections are the same as in the connection example for IBM PC or IBM compatible PCs.  
How to attach the ferrite core  
Attach the ferrite core when using the S-video cable or infrared remote sensor extension unit which are sold separately.  
ony if they are connected directly to the projector.  
1 Release the stopper at each end and  
open the ferrite core.  
Stoppers  
Wind the cable once.  
2 Wind the cord around the ferrite core.  
Attach the ferrite core about 3 cm from the end of the  
cord.  
3 Close the ferrite core with the cord  
Click!  
inside until you hear it click shut.  
Note  
• When connecting, connect the terminal which is at the  
ferrite core end of the cord to the projector.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to Various Devices  
Connecting the Power Cord  
After all devices have been finished being connected, connect the supplied power cord. At this time, do not yet turn on the  
MAIN POWER switch.  
1 Insert the supplied power cord into the  
R
E
T
N
E
U
N
O
E
M E  
D
I
V
C
P
T
I
X E  
T E A R E P  
O
T
E S E  
K
R
P
E
D
I
O
T
N E  
S Y E  
P
M
H
E
T
P
M
A
L
power input terminal of the projector.  
N
W
O
D
P
U
Ferrite core  
2 Insert the main plug of the supplied  
power cord into a suitable wall outlet.  
Power cord (supplied)  
CAUTIONS  
CAUTIONS  
To prevent fire and electric shock, observe the  
following:  
• Since the power requirement of the projector is high, insert  
• When you do not use devices, pull out their power cords  
from wall outlets.  
• Do not connect the devices with power cords other than  
those supplied.  
• Do not use mains voltage other than the power voltage  
indicated.  
• Do not scar, damage, or work on the power cords. Also, do  
not put a heavy object on, heat, or stretch the power cords,  
otherwise they may be damaged.  
for European  
for United Kingdom  
continent countries  
the power plug directly into a wall outlet.  
• Use the supplied power cord with the ferrite core only.  
• Do not remove the ferrite core from the supplied power  
cord; Otherwise, there may be a possibility that a harmful  
interference occurs.  
• Do not insert or pull out the plugs with a wet hand.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Lamp control settings  
After turning the power on, first perform the lamp control settings on the setting menu referring to “Setting and Adjusting Other  
Functions (OPTIONS)” on page 54.  
There are 3 modes in the lamp control settings.  
1: NORMAL MODE (Normal)  
Used as a normal lamp.  
The projector is set to “Normal” mode at the time of purchase.  
* “Lamp replacement” appears on the screen when the lamp use time exceeds 1000 hours.  
2: LIGHT POWER CONTROL MODE (LPC)  
Automatically controls the power used by the lamp and increases it in steps. When this mode is used, the brightness  
starts at approximately 70%. The decrease in brightness is slower than in “Normal” mode and this mode is best suited  
when using the projector continuously for long periods of time.  
* “Lamp replacement” appears on the screen when the lamp use time exceeds 2000 hours.  
3: LIGHT OUTPUT CONTROL MODE (LOC)  
The brightness can be set in seven levels (-6 to 0). Since the brightness can be set in steps, this is the mode best suited  
for adjusting multiple screens. This setting can also be changed while the projector is being used. To change the setting,  
choose LOC with the 5/cursors and choose the level with the 2/3cursors.  
* “Lamp replacement” appears on the screen when the lamp use time exceeds 2000 hours.  
The lamp replacement time is different for the 3 modes.  
1: NORMAL MODE (Normal) ... 1000 hours  
2: LIGHT POWER CONTROL MODE (LPC) ... 2000 hours  
3: LIGHT OUTPUT CONTROL MODE (LOC) ... 2000 hours  
* These lamp replacement times are only a rough guide as to how long the lamp will last if these modes are used from the  
beginning. These are not guaranteed service lives.  
Notes  
• Although the LIGHT OUTPUT CONTROL MODE (LOC) and LIGHT POWER CONTROL MODE (LPC) electrically control  
the brightness of the lamp and extend the replacement time longer than that for the NORMAL MODE, the service life of the  
lamp is approximately 1000 hours.  
• The lamp will gradually become less bright in each mode.  
Since the lamp may become less bright quickly in some usage environments, replace the lamp if you notice that it is no  
longer bright even if the lamp has not yet reached the end of its life.  
• Mode settings  
* If the projector is not put in stand-by mode or turned off after the lamp has been used continuously in the normal mode for  
more than 1000 hours (but less than 2010 hours), it can be used for “up to 2010 hours”.  
However, if the projector is put in stand-by mode or turned off, it can not be turned back on again.  
* If the projector is put in stand-by mode or turned off after the lamp has been used in the light output control mode or light  
power control mode for more than 2000 hours (but less than 2010 hours), it can not be turned back on again.  
However, if the projector is not put in stand-by mode or turned off, it can be used for “up to 2010 hours”.  
* If the projector is used in the light output control mode or light power control mode for more than 1000 hours, and then  
switched to the normal mode, put in stand-by mode or turned off, it can not be turned back on again.  
After performing the above settings, perform the necessary settings.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                                          
Basic Operations  
The following describes the basic procedure for normal use  
of the projector.  
Projector’s buttons  
STAND BY indicator  
OPERATE indicator  
STAND BY  
LAMP  
TEMP  
1. Turning on the Power  
OPERATE  
HIDE  
OPERATE button  
1 Turn on the MAIN POWER switch.  
PC  
ON [ ]:The main power turns on and the STAND BY  
indicator comes on.  
KEYSTONE  
PRESET  
VIDEO  
MENU  
Projector’s indicator  
STAND BY  
OPERATE  
EXIT  
ENTER  
2 Press the OPERATE button for one  
second or more.  
R
T E  
E N  
U
O
M E N  
I D E  
V
C
P
T
X I E  
E
T
A
E R P  
• The OPERATE indicator lights and the projected  
screen slowly appears.  
O
T
E
S
E
N
P
R E  
O
T
I D E  
H
Y S  
K E  
E
T
A M P  
L
N
W
O
D
P
U
Projector  
Remote control unit  
STAND BY  
OPERATE  
OPERATE  
or  
Notes  
• After the power is turned on, the image may be jumbled for  
a few seconds, but this is not a malfunction.  
• After the indicator comes on, it can take a minute or so for  
the lamp to warm up and operate consistently.  
Turning off the Power  
1 Press the OPERATE button for one  
second or more.  
Remote control unit  
• The STAND BY indicator changes to blinking, and the  
projector goes into cool-down mode. The cool-down  
mode will continue for approximately 120 seconds.  
Remote control unit  
Projector (Blinking)  
QUICK  
OPERATE  
ALIGN.  
OPERATE button  
OPERATE  
HIDE  
STAND BY  
OPERATE  
W
SCREEN FREEZE  
S
COMP  
DVI  
VIDEO  
Y/C  
PC1  
PC2  
T
T
ZOOM  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
W
W
PRESET  
Note  
• The OPERATE button will not work for approximately 1  
minute from when the light-source lamp is turned on. Use  
the button after approximately 1 minute.  
EXIT  
ENTER  
RM-M160 REMOTE CONTROL UNIT  
2 Turn off the MAIN POWER switch after  
the STAND BY indicator changes to  
steady on.  
OFF []:The MAIN POWER switch turns off and the  
STAND BY indicator goes off.  
Projector  
STAND BY  
OPERATE  
CAUTION  
• Do not turn off the MAIN POWER switch during cool-down  
mode (the STAND BY indicator blinking). Turn it off after  
the STAND BY indicator becomes on (stand-by mode).  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Projector’s buttons  
2. Select the Input source to be Projected  
Press the VIDEO button or the PC button to switch the input.  
• Each time you press either button, the selected input  
changes as follows. The selected name appears on the top  
right of the image on the screen for five seconds. (Called  
line display.)  
STAND BY  
LAMP  
TEMP  
OPERATE  
HIDE  
PC  
PC button  
KEYSTONE  
PRESET  
When selecting an image device connected to the  
AV IN (VIDEO, Y/C or COMP) terminal:  
VIDEO  
MENU  
VIDEO button  
Projector  
Press VIDEO.  
The input mode changes as follows every time the button is  
pressed.  
EXIT  
ENTER  
VIDEO Y/C COMP  
Remote control unit  
Press the “VIDEO”, “Y/C” or “COMP” button.  
Remote control unit  
VIDEO: The image from the VIDEO input terminal on the  
side of the unit is projected.  
Y/C:  
The image from the Y/C input terminal on the side of  
the unit is projected.  
QUICK  
OPERATE  
ALIGN.  
PC button  
HIDE  
COMP: The image from the COMP (Y, RB/B-Y, PR/R-Y)  
input terminal on the side of the unit is projected.  
* When there is no signal from the selected input terminal  
(No signal), “No Input” is displayed.  
W
SCREEN FREEZE  
S
COMP  
DVI  
VIDEO  
Y/C  
VIDEO button  
ZOOM button  
PC1  
PC2  
T
T
ZOOM  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
W
W
PRESET  
When selecting a device such as a computer  
which is connected to the PC1, PC2 or DVI  
terminal:  
EXIT  
ENTER  
Projector  
Press PC.  
RM-M160 REMOTE CONTROL UNIT  
The input mode changes as follows every time the button is  
pressed.  
PC1 PC2 DVI  
Language display  
Remote control unit  
Press the “PC1”, “PC2” or “DVI” button.  
The display languages of the menus, direct buttons  
(DIGITAL ZOOM, KEYSTONE, etc) and messages is set to  
“ENGLISH” when the projector is bought. The display  
language can be selected from the following 6 languages:  
PC1: The image from the PC1 input terminal on the side of  
the unit is projected.  
PC2: The image from the PC2 input terminal on the side of  
the unit is projected.  
DVI: The image from the DVI input terminal on the side of  
the unit is projected.  
* When there is no signal from the selected input terminal  
(No signal), “No Input” is displayed.  
(Japanese)”, “English (English)”, “Deutsch  
(German)”, “Español (Spanish)”, “Italiano (Italian)” and  
“Français (French)”. (Refer to page 46.) However, some  
words (VIDEO, NTSC, Quick Alignment, etc) are only  
displayed in English.  
Remote control unit  
Projector  
SCREEN FREEZE  
COMP  
VIDEO  
PC  
S
PC1  
PC2  
DVI  
Y/C  
VIDEO  
[Screen display]  
Line Display  
VIDEO  
PC 1  
PC 2  
Y/C  
COMP  
DVI  
VIDEO  
* To show the line display (Y/C, VIDEO, COMP, PC1, PC2 or  
DVI) or not is selectable by the menu. Refer to “Setting and  
Adjusting Other Functions (OPTIONS)” on page 54.  
Note  
• When no image signal is input to the selected input  
terminal, the message “No Input” is displayed on the  
screen. (Refer to page 67.)  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Projector’s buttons  
3. Adjust the Screen Size (Zooming)  
How to adjust the projected screen size differs depending on  
the lens unit (optional) you are using.  
STAND BY  
OPERATE  
LAMP  
TEMP  
HIDE  
GL-M2910G (without zooming function):  
The projected screen size cannot be changed.  
PC  
KEYSTONE  
PRESET  
GL-M2915SG/GL-M2920ZG/GL-M2930SZG (with  
zooming function):  
VIDEO  
MENU  
Adjust the projected screen size with the following buttons on  
the remote control unit.  
PRESET button  
EXIT button  
Note  
EXIT  
ENTER  
• The function of GL-M2915SG is to adjust the view angle  
zooming by 2%. (For fine view angle adjustment)  
To enlarge the projected screen size  
Press the ZOOM W (Wide) button.  
Remote control unit  
To reduce the screen size  
Press the ZOOM T (Tele) button.  
Remote control unit  
T
DIGITAL  
ZOOM  
QUICK  
ALIGN.  
OPERATE  
W
HIDE  
W
SCREEN W/S button  
SCREEN FREEZE  
COMP  
DVI  
VIDEO  
Y/C  
S
4. Adjust Focus  
PC1  
PC2  
FOCUS +/– button  
ZOOM T/W button  
T
T
ZOOM  
Adjust focus with the following buttons on the remote control unit.  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
W
W
PRESET  
To focus on farther points:  
Press the FOCUS + button.  
PRESET button  
EXIT button  
To focus on nearer points:  
EXIT  
ENTER  
Press the FOCUS – button.  
Remote control unit  
RM-M160 REMOTE CONTROL UNIT  
FOCUS  
5. Setting the Screen Aspect Ratio  
Set in accordance with the screen aspect ratio that will be  
used. When a screen aspect ratio of 16:9 is used, a 4:3  
image can be projected within the screen without using the  
zoom function.  
When using a 16:9 screen:  
Press the “W” button.  
When using a 4:3 screen:  
Press the “S” button.  
Remote control unit  
W
SCREEN  
S
* There is no button on the unit.  
* This setting can also be performed from the menu. (Refer  
to page 46.)  
Note: for proper operation with the  
Video Processor and anamorphic  
lens, the projector should stay in  
the 4:3 mode. Aspect ratio control  
is operated with the Video Processor.  
Aspect ratio control for HDTV pass  
-through is controlled by the projector.  
• When using a screen with a 16:9 aspect ratio  
When set to “S” (4:3)  
* If a 4:3 image is projected, some  
parts of the top and bottom of the  
image may not be displayed.  
When set to “W” (16:9)  
* A 4:3 image will be displayed in full  
in the middle of the screen.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Projector’s buttons  
Turning off Image (HIDE)  
STAND BY  
OPERATE  
Video image can be temporarily turned off.  
LAMP  
TEMP  
Press the HIDE button once:  
Video image instantly turn off.  
HIDE  
HIDE  
button  
PC  
Press the HIDE button again:  
Video image come on again.  
KEYSTONE  
PRESET  
KEYSTONE  
VIDEO  
MENU  
/
buttons  
Remote control unit  
Projector  
HIDE  
PRESET  
button  
HIDE  
EXIT  
button  
EXIT  
ENTER  
Note  
Remote control unit  
• When the projected image input is changed, the HIDE  
function is canceled and the image return.  
Removing the Trapezoidal Distortion of  
the Image  
HIDE button  
QUICK  
ALIGN.  
OPERATE  
HIDE  
If the image projected on the screen is distorted in trapezoid  
form, correct it with the KEYSTONE buttons on the projector.  
When the KEYSTONE button is pressed, “Keystone”  
appears on the screen together with the level bar and set  
value (–80 to 128). When “15 sec.” is displayed in the menu,  
“Keystone” will appear in approximately 15 seconds.  
W
SCREEN FREEZE  
COMP  
DVI  
VIDEO  
Y/C  
S
PC1  
PC2  
T
KEYSTONE  
T
ZOOM  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
/
buttons  
W
W
PRESET  
PRESET button  
Keystone  
123  
EXIT button  
EXIT  
ENTER  
When you press the KEYSTONE  
button:  
The trapezoid form is corrected as shown in the figure.  
RM-M160 REMOTE CONTROL UNIT  
When you press the KEYSTONE  
button:  
The top bottom inverted trapezoid form is corrected as  
shown in the figure.  
* To cancel correction and restore the original screen, press  
the PRESET button. (Adjusted value:0)  
* Press the EXIT button to immediately remove the keystone  
display.  
Remote control unit  
Projector  
KEYSTONE  
KEYSTONE  
Projected image with trapezoidal distortion  
KEYSTONE  
KEYSTONE  
Notes  
• The trapezoidal distortion (keystone) can be adjusted from  
the option menu. (Refer to page 54.)  
• The range of the trapezoidal distortion adjustment is  
approximately 20° in the vertical direction.  
• Interference patterns may appear on the screen when  
adjusting the keystone. This is not a malfunction.  
• Depending on the type of signal, some noise may appear in  
the picture when the keystone is adjusted.  
This is not a malfunction.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Remote control unit  
Quick Alignment Function  
(QUICK ALIGN.)  
The Quick Alignment function automatically adjusts (sets)  
the screen settings of the image input from the PC1, PC2 or  
DVI input terminals. This can only be performed from the  
remote control.  
QUICK  
ALIGN.  
OPERATE  
QUICK ALIGN.  
HIDE  
W
button  
SCREEN FREEZE  
COMP  
DVI  
VIDEO  
Y/C  
S
PC1  
PC2  
T
While projecting an image on the screen, press the QUICK  
ALIGN. button on the remote control.  
Quick alignment is conducted to obtain best image.  
* During the automatic alignment, “Quick Alignment” appears  
on the screen, and then disappears when the alignment is  
completed.  
T
ZOOM  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
W
W
PRESET  
EXIT  
ENTER  
Remote control unit  
QUICK  
ALIGN.  
RM-M160 REMOTE CONTROL UNIT  
[Screen display]  
Q u i c k A l i g n m e n t  
Notes  
• This only works for the signals input from the PC1, PC2 or  
DVI input terminals. It does not work for the signals input  
from the AV IN terminal (VIDEO, Y/C or COMP input  
terminal).  
• The quick alignment function is used to automatically adjust  
the “Horizontal and vertical position”, “Phase” and  
“Tracking” of the projected image.  
• When using the quick alignment function to automatically  
adjust the image, use a bright, still-picture. It may not  
function correctly on a dark or motion picture. If the results  
obtained with the quick alignment function are not  
satisfactory, manually adjust the “Horizontal and vertical  
position”, “Phase” and “Tracking” of the projected image.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Remote control unit  
Displaying a Still Picture (FREEZE)  
While projecting an image, a still picture is obtained at any  
time by using the FREEZE button on the remote control.  
When you press the FREEZE button:  
QUICK  
ALIGN.  
OPERATE  
“FREEZE” appears on the screen for a few seconds and  
then the still picture is shown on the screen. Refer to the  
FREEZE message shown on the left of this page.  
* To forcibly clear “FREEZE”, press the EXIT button.  
HIDE  
W
SCREEN FREEZE  
COMP  
DVI  
VIDEO  
Y/C  
S
FREEZE button  
PC1  
PC2  
T
DIGITAL ZOOM  
T/W button  
When you press the FREEZE button again.  
The original image resumes.  
T
ZOOM  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
W
W
PRESET  
PRESET button  
EXIT button  
Remote control unit  
FREEZE  
Cursor buttons  
5// 2/3  
EXIT  
ENTER  
Notes  
RM-M160 REMOTE CONTROL UNIT  
• During freezing, the picture sent from the signal source is  
lost.  
• If any of the inoperative buttons (“MENU”, “QUICK ALIGN.”,  
“KEYSTONE”) are pressed while displaying a still picture,  
“FREEZE” is displayed on the screen.  
FREEZE message  
• This function will not work with some signal sources  
(UXGA, etc). In this case, the FREEZE inhibit message  
appears for a few seconds, as shown on the left. To forcibly  
clear this message, press the EXIT button.  
FREEZE  
Zooming a Part of the Image  
(DIGITAL ZOOM T/W)  
A part of the image being projected can be digitally magnified up  
to four times. When the DIGITAL ZOOM T or W button is  
pressed, “Digital zoom” appears on the screen together with the  
FREEZE inhibit message  
level bar and magnifying power (  
2.5, 3.2, 4.0). When “15 sec.” is displayed in the menu,  
“Digital zoom” will appear in approximately 15 seconds.  
×1.0,  
×1.2,  
×1.4,  
×1.6,  
×2.0,  
×
×
×
Digital zoom  
1.2  
• To zoom up or zoom down, press the DIGITAL ZOOM T or  
W button on the remote control.  
FREEZE  
Remote control unit  
T
DIGITAL  
ZOOM  
W
DIGITAL ZOOM inhibit message  
Moving the zoomed image:  
While “Digital zoom” appears on the screen, you can move  
the zoomed image with the cursor (5//2/3) button on the  
remote control.  
5: Upper part of the image will be  
displayed.  
: Lower part of the image will be  
displayed.  
D.ZOOM  
2: Left side part of the image will  
be displayed.  
3: Right side part of the image  
will be displayed.  
Notes  
• This function will not work with some signal sources  
(UXGA, etc). In this case, the DIGITAL ZOOM inhibit  
message appears for a few seconds, as shown on the left.  
To forcibly clear this message, press the EXIT button.  
• The quality of the zoomed image reduces in comparison  
with the original one.  
• To return to the original size (×1.0) and original position,  
press the PRESET button while “Digital zoom” is displayed  
on the screen.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
You can adjust picture quality, set functions, get information on the input video signal, etc. using the menus. From the  
following menu transition diagrams, you can see the overall menus and basic button operation in menu mode. Note that there  
are three menu modes, No signal menu mode, video menu mode and PC menu mode. When the MENU button is pressed,  
the projector enters one of these modes by judging the input signal being received.  
Menu Transition Diagram in No signal Menu Mode  
This is displayed if there is no signal from the selected input terminal.  
Main menu in No signal Menu Mode  
Submenus in No signal Menu Mode  
Press 5/to select an item.  
Press 5/to select an item.  
Press 2/3to set the value.  
Menu  
Set up  
3or ENTER  
Sync level  
Low  
Std  
High  
Set up  
Sync level  
Sync timing  
Sync timing  
Options  
EXIT  
Language  
Information  
5
Press 5/to select an item.  
5
Menu  
Language  
3or  
Set up  
English  
Deutsch  
Español  
Italiano  
Français  
English  
Deutsch  
Español  
Italiano  
Français  
ENTER  
Options  
Language  
Information  
EXIT  
5
Menu  
Input  
PC1  
Set up  
Switcher  
CH.0  
123 h  
Options  
Language  
Information  
Lamp time  
Quick Reference Guide for No signal Menu Mode  
Main Menu in No signal Menu Mode  
Set up  
Sync level:  
Sync timing:  
Low. Std*. High.  
3-5  
Options  
Flip H:  
Flip V:  
OFF* / ON (Select for upside-down hanging on the ceiling.)  
OFF* / ON (Select for upside-down hanging on the ceiling.)  
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*  
Sleep time [min]: Selectable sleep times. If no-signal condition continues for the period of selected time  
(Unit: Minutes), the projector enters the stand-by mode. 15 / 30 / 60 / OFF*  
Language  
Japanese / English* / German / Spanish / Italian / French  
Information  
Language for on-screen display.  
Input:  
Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, COMP,  
PC1, PC2 or DVI)  
Switcher:  
Lamp time:  
Has no meaning. This display currently has no meaning. (“CH.0” is usually displayed to  
indicate that it is not being used.)  
Accumulated used hours of the light-source lamp.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Menu Transition Diagram in Video Menu Mode  
Main menu in Video Menu Mode  
Submenus in Video Menu Mode  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
Press 2/3to select Yes or No.  
Then, press ENTER to execute.  
Press 5/to select an item.  
Menu  
Image adj.  
Image adj.  
Contrast  
Brightness  
Color  
12  
12  
12  
12  
1
Image adj.  
Contrast  
3or  
Set up  
Brightness  
All reset?  
EXIT  
ENTER  
Color  
Color temp.  
Options  
Tint  
Yes  
No  
Tint  
Sharpness  
All reset  
EXIT  
Language  
Information  
Sharpness  
All reset  
ENTER  
ENTER  
5
Press ENTER to select an item.  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
5
Press 5// 2/3 to move the video screen/menu position.  
Position  
Menu  
Set up 1  
Position  
Gamma  
Image adj.  
Set up  
ENTER  
3or  
Position  
Gamma  
Aspect ratio  
Decoder  
Page 2  
ENTER  
Down  
Aspect ratio  
Decoder  
Tracking  
Deinterlace  
Phase  
ENTER  
Disp.Posi.  
12,12  
Menu  
Color temp.  
Options  
Cinema  
4:3  
Up  
EXIT  
16:9  
ENTER  
ENTER  
Language  
Information  
ENTER  
ENTER  
EXIT  
Screen  
HDTV  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
ENTER  
Press 5/to select an item.  
Set up 1  
Decoder  
Position  
ENTER  
Down  
AUTO  
NTSC  
[
NTSC  
]
Gamma  
Aspect ratio  
Page 2  
Cinema  
4:3  
Up  
5
16:9  
NTSC4.43  
PAL  
ENTER  
SECAM  
Set up 2  
Tracking  
Phase  
Screen  
HDTV  
123  
12  
4:3  
16:9  
1080i  
1035i  
Page 1  
ENTER  
Press 5/to select an item.  
Set up 2  
* The film function is  
displayed when the  
input signal is  
equivalent to NTSC  
or PAL. The tracking  
function is displayed  
for other signals.  
Deinterlace  
Phase  
Video Film  
AUTO  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
12  
Menu  
4:3  
16:9  
1035i  
Screen  
HDTV  
Color temp.  
Image adj.  
Set up  
ENTER  
Color temp.  
RED  
3or  
1080i  
Color temp.  
RED  
Low  
Middle  
High  
ENTER  
Page 1  
ENTER  
GREEN  
BLUE  
Color temp.  
Options  
123  
123  
123  
GREEN  
BLUE  
Call reset  
Language  
Information  
EXIT  
EXIT  
All reset  
ENTER  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
Press 5/to select an item.  
Color temp.  
5
Press 2/3to set or adjust the value.  
Menu  
Options  
All reset?  
Menu display  
15sec  
5sec  
ON  
ON  
Menu display  
Line display  
Image adj.  
Set up  
3or  
ENTER Line display  
OFF  
OFF  
Yes  
No  
Lamp time display  
Keystone  
Color temp.  
Options  
Lamp time display  
Lamp control  
Keystone  
Lamp control  
Page 2  
ENTER  
ENTER  
Language  
Information  
EXIT  
ENTER  
ENTER  
EXIT  
ENTER  
You can see the information.  
Press 5/to select an item.  
Language  
5
Keystone  
123  
Menu  
ENTER  
3or  
Image adj.  
Set up  
Lamp control  
ENTER  
English  
English  
Deutsch  
Español  
Italiano  
Français  
Color temp.  
Options  
Deutsch  
Español  
Normal  
LPC  
LOC  
EXIT  
Language  
Information  
Italiano  
Français  
5
Menu  
Page 2  
Image adj.  
Set up  
Input  
PC1  
CH.0  
Flip H  
Flip V  
OFF  
OFF  
ON  
ON  
Switcher  
Source  
Color temp.  
Options  
NTSC  
RS-232C [bps]  
Sleep time [min]  
Page 1  
9600  
30  
19200  
60 OFF  
15  
Language  
Information  
Lamp time  
123 h  
ENTER  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
Note  
• The display languages of the menus are set to “English” when the projector is  
bought. The display language can be selected from the following 6 languages:  
(Japanese)”, “English (English)”, “Deutsch (German)”, “Español (Spanish)”,  
“Italiano (Italian)” and “Français (French)”. (Refer to page 46.)  
The language settings in the section are explained in “English”.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
.
Quick Reference Guide for Video Menu Mode  
Main Menu in Video Menu Mode (While receiving video-device-related signals)  
Image adj. (Refer to page 49)  
Contrast:  
Brightness:  
Color:  
Contrast of the video image being projected can be adjusted. (–30 to +30, 0*)  
Brightness of the video image being projected can be adjusted. (–30 to +30, 0*)  
Color density of the video image being projected can be adjusted. (–30 to +30, 0*)  
Tint of the video image being projected can be adjusted. (–30 to +30, 0*)  
Sharpness of the video image being projected can be adjusted. (–5 to +5, 0*)  
Resets above items to the factory set values.  
Tint:  
Sharpness:  
All reset:  
Yes / No  
Set up 1  
Position:  
Video screen position and menu position can be adjusted. (Refer to page 51)  
Disp. Posi. / Menu  
Image tone can be changed. Down/Cinema*/Up (Suitable for the cinema programes)(Refer to  
Gamma:  
page 52)  
Aspect ratio  
Decoder:  
Selectable aspect ratio, 4:3*/16:9. (Refer to page 52)  
Selectable color systems, Normally, set to AUTO. (Refer to page 45)  
(This item is displayed only when inputting VIDEO or Y/C.)  
AUTO*/NTSC/NTSC4.43/PAL/SECAM  
Page 2 Press ENTER to enter the “Set up 2” submenu  
Tracking: Normally, no adjustment is required. The lateral size and display area of video image can be  
adjusted. (–128 to + 127) (Refer to page 47)  
Deinterlace: Set when watching movies which were recorded on film.  
Phase:  
Screen:  
HDTV:  
Page 1:  
Flickering or dim picture image can be adjusted. (0 to 31) (Refer to page 47)  
Selectable screen’s aspect ratio. 4:3*/16:9 (Refer to page 46)  
Selectable HDTV format. Normally, set to 1080i, 1080i*/1035i (Refer to page 46)  
Press ENTER to return to “Page 1” submenu.  
Color temp.  
Color temp.:  
Adjustable color temperature, Low/Middle*/High.  
Will be adjusted to correct reddish or blueish image.  
RED:  
Adjusts the red level. (0 to 255, the adjustable range varies depending on signals)  
GREEN:  
BLUE:  
All-reset:  
Adjusts the green level. (0 to 255, the adjustable range varies depending on signals)  
Adjusts the blue level. (0 to 255, the adjustable range varies depending on signals)  
Reset above items to the factory set values.  
Yes/No  
Options (Refer to page 54)  
Options 1  
Menu display:  
15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)  
Line display:  
5sec* (Line display such as “VIDEO”, “Y/C”, “PC1”, or “PC2” appears on top right of the screen for  
5 seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)  
Lamp time display:  
ON*:  
Displays when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.  
Does not display when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.  
OFF:  
Keystone:  
Keystone:  
Press ENTER to enter the Keystone submenu.  
Adjust to correct the trapezoidal distortion of the projected image.  
(–80 to +120, 0*)  
Lamp control:  
Normal*: Used as a normal lamp.  
LPC:  
LOC:  
Page 2:  
Flip H.:  
Lamp brightness is automatically controlled with time.  
Lamp brightness is controlled in 7 levels (-6 to 0) irrespective of the time. This is set within the menu.  
Press ENTER to enter the “Page 2” submenu.  
OFF* / ON (Select for upside-down hanging on the ceiling.)  
OFF* / ON (Select for upside-down hanging on the ceiling.)  
Flip V:  
RS-232C [bps]:  
Sleep time [min]:  
Selectable baud rate (transmission speed). 9600 / 19200*  
Selectable sleep times. If no-signal condition continues for the period of  
selected time (Unite: Minutes), the projector enters the stand-by mode. 15 / 30  
/ 60 / OFF*  
Page 1:  
Press ENTER to return to the “Page 1” submenu.  
Language  
Language for on-screen display. (Refer to page 46)  
Japanese / English* / German / Spanish / Italian / French  
Information (Refer to page 56)  
Input:  
Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, COMP, PC1, PC2 or DVI)  
Switcher:  
Has no meaning. This display currently has no meaning, (“CH.0” is usually displayed to indicate  
that it is not being used.)  
Source:  
Shows the projected image’s type of video signal.  
Lamp time:  
Accumulated used hours of the light-source lamp.  
* : Factory set value.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Menu Transition Diagram in PC Menu Mode  
Main menu in PC Menu Mode  
Submenus in PC Menu Mode  
Press 2/3to select Yes or No.  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
Press 5/to select an item.  
Then, press ENTER to execute.  
Menu  
Image adj.  
Image adj.  
Contrast  
3or  
Image adj.  
Set up  
EXIT  
All reset?  
Brightness  
ENTER  
Sharpness  
All reset  
Color temp.  
Options  
Contrast  
12  
12  
ENTER  
Yes  
No  
Brightness  
Sharpness  
All reset  
Language  
Information  
EXIT  
1
2
3
4
5
ENTER  
5
Press ENTER to select an item.  
Press 5// 2/3 to move the  
video screen/menu position.  
5
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
Menu  
Position  
Set up 1  
Image adj.  
Set up  
Tracking  
Phase  
3or  
ENTER  
Tracking  
Phase  
123  
12  
ENTER  
Disp.Posi.  
12,12  
Menu  
Color temp.  
Options  
Position  
Resize  
Clamp  
Position  
Resize  
Clamp  
ENTER  
ENTER  
Language  
Information  
EXIT  
EXIT  
1:1  
ST  
Panel  
Aspect  
BP  
Set up 1  
5
Position  
Resize  
ENTER  
1:1  
Press 2/3to select Yes or No.  
Panel  
Aspect  
Then, press ENTER to execute.  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
Color temp.  
Menu  
Color temp.  
Image adj.  
Set up  
EXIT  
3or  
ENTER  
Color temp.  
RED  
Color temp.  
RED  
Low  
Middle  
High  
All reset?  
Color temp.  
Options  
123  
123  
123  
Yes  
No  
GREEN  
BLUE  
GREEN  
BLUE  
Language  
Information  
EXIT  
All reset  
All reset  
ENTER  
ENTER  
Press 5  
Press 2  
/
to select an item.  
5
/
3to set or adjust the value.  
Keystone  
0
Menu  
Options  
ENTER  
Menu display  
Line display  
Lamp time display  
Keystone  
15sec  
5sec  
ON  
ON  
Menu display  
Line display  
Image adj.  
Set up  
3or  
ENTER  
OFF  
OFF  
Lamp time display  
Keystone  
Color temp.  
Options  
EXIT  
Lamp control  
ENTER  
ENTER  
EXIT  
Language  
Information  
Lamp control  
Page 2  
ENTER  
ENTER  
Press 5/to  
select an item.  
Language  
5
ENTER  
Menu  
Lamp control  
Image adj.  
Set up  
Normal  
LPC  
English  
Deutsch  
Español  
Italiano  
Français  
English  
Deutsch  
Español  
Italiano  
Français  
Color temp.  
Options  
LOC  
Language  
Information  
Page 2  
5
Flip H  
Flip V  
OFF  
OFF  
9600  
30  
ON  
ON  
Menu  
RS-232C [bps]  
Sleep time [min]  
Page 1  
19200  
Image adj.  
Set up  
Input  
PC 1  
CH.0  
15  
60 OFF  
Switcher  
ENTER  
Color temp.  
Options  
Resolution  
Frequency H  
Frequency V  
Lamp time  
NTSC  
79.9 kHz  
75 Hz  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
Language  
Information  
123  
h
You can see the information.  
Note  
• The display languages of the menus are set to “English” when the projector is  
bought. The display language can be selected from the following 6 languages:  
(Japanese)”, “English (English)”, “Deutsch (German)”, “Español  
(Spanish)”, “Italiano (Italian)” and “Français (French)”. (Refer to page 46.)  
The language settings in the section are explained in “English”.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Quick Reference Guide for PC Menu Mode  
Main Menu in PC Menu Mode (While receiving computer-related signals)  
Image adj. (Refer to page 49)  
Contrast:  
Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)  
Brightness:  
Sharpness:  
All reset:  
Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)  
Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)  
Resets above items to the factory set values.  
Yes / No  
Set up  
Tracking:  
The lateral size and display area of picture image can be adjusted. (–128 to +127)  
(Refer to page 47)  
Phase:  
Position:  
Flickering or dim picture image can be adjusted. (0 to 31) (Refer to page 47)  
Video screen position and menu position can be adjusted. (Refer to page 51)  
Disp. Posi. / Menu  
Resize:  
The relationship between the number of pixels (resolution) and the screen can be  
selected. (Refer to page 53)  
“1:1”:  
Picture image is projected with its original size.  
Panel:  
Aspect*:  
Picture image is enlarged to the full size.  
Picture image is enlarged while maintaining the original aspect ratio.  
Selectable clamp position. Normally, set to “BP”. ST / BP*  
Clamp:  
Color temp.  
Color temp.:  
Adjustable color temperature, Low/Middle* /High.  
Will be adjusted to correct reddish or blueish image.  
RED:  
GREEN:  
BLUE:  
Adjusts the red level. (o to 255, the adjustable range varies depending on signals)  
Adjusts the green level. (o to 255, the adjustable range varies depending on signals)  
Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)  
Reset above items to the factory set values.  
All-reset:  
Yes/No  
Options (Refer to page 54)  
Options 1  
Menu display:  
Line display:  
15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)  
5sec* (Line display such as “PC1” or “PC2” appears on top right of the screen for 5  
seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not  
appear.)  
Lamp time display:  
ON*:  
Displays when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.  
Does not display when the lamp use time reaches 1000 hours when set in the LPC or LOC  
mode.  
OFF:  
Keystone:  
Press ENTER to enter the Keystone submenu.  
Adjust to correct the trapezoidal distortion of the projected image.  
(–80 to +128, 0*)  
Keystone:  
Lamp control:  
Normal*: Used as a normal lamp.  
LPC:  
LOC:  
Lamp brightness is aLutomatically controlled with time.  
Lamp brightness is controlled in 7 levels (-6 to 0) irrespective of the time. This is set within  
the menu.  
Page 2:  
Press ENTER to enter the “Page 2” submenu.  
Flip H:  
Flip V:  
OFF* / ON (Select for upside-down hanging on the ceiling.)  
OFF* / ON (Select for upside-down hanging on the ceiling.)  
RS-232C [bps]:  
Sleep time [min]:  
Selectable baud rate (transmission speed). 9600 / 19200*  
Selectable sleep times. If no-signal condition continues for the  
period of selected time (Unite: Minutes), the projector enters the  
stand-by mode. 15 / 30 / 60 / OFF*  
Page 1:  
Press ENTER to return to the “Page 1” submenu.  
Language  
Language for on-screen display. (Refer to page 46)  
Japanese / English* / German / Spanish / Italian / French  
Information (Refer to page 56)  
Input:  
Switcher:  
Resolution:  
Shows the terminal name selected by the PC button. (PC1 or PC2)  
This display currently has no meaning. (“CH.0” is usually displayed to indicate that it is not being used.)  
Shows the resolution of the input signal being received. (Horizontal × Vertical)  
It may not be displayed correctly with some input signals.  
Frequency H:  
Frequency V:  
Lamp time:  
Shows the horizontal frequency of the input signal being received. ( kHz)  
Shows the vertical frequency of the input signal being received. ( Hz)  
Accumulated used hours of the light-source lamp.  
* : Factory set value.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                                         
                                                                                              
                                                   
When an item which has the “ENTER” message has been  
selected in step 4, press the ENTER button to move to the  
next submenu.  
                                               
                                                                                              
Menu Operations  
Basic Menu Operation  
When the MENU button is pressed, the projector enters Video or PC menu mode by responding to the input signal being  
received.  
Video menu mode:  
Enters this mode when video-device-related signals are  
input from the following devices.  
• Video devices connected to the VIDEO IN (Y/C, VIDEO  
4 Press the cursor button 5or to  
select an item in the submenu.  
When a “Language” has been selected in step 2, press  
to set the language.  
and COMP) terminals.  
Remote control unit  
Projector  
PC menu mode:  
Enters this mode when computer-related signals are input  
from the following devices.  
• A computer connected to the PC 1 terminal.  
• A computer connected to the PC 2 terminal, which outputs  
analog RGB, V, H/Cs signals.  
• A computer connected to the DVI terminal.  
5 Press the cursor button 2 or 3 to set  
1 Press the MENU button.  
or adjust the value.  
The main menu is displayed on the screen.  
Remote control unit  
Projector  
Remote control unit  
MENU  
Projector  
MENU  
2 Press the cursor button 5or to  
select an item in the main menu.  
Remote control unit  
Projector  
• All reset  
• Position  
• Decoder (Refer to page 45)  
• Keystone (Refer to page 54)  
(Refer to page 49)  
(Refer to page 51)  
• Page 1  
• Page 2  
(Refer to page 54)  
(Refer to page 54)  
To exit the main menu:  
• While the main menu is displayed, press the MENU button.  
The main menu disappears and the original picture image  
resumes.  
3 Press the cursor button 3 or the  
ENTER button to enter the submenu.  
The submenu corresponding to the item selected in step  
2 is displayed on the screen.  
To exit the submenu:  
• While the submenu is displayed, press the EXIT button.  
The menu returns to the previous menu.  
• To exit the menu mode directly, press the MENU button.  
The submenu disappears and the original video image is  
restored.  
* When you selected “Information” in step 2, no  
submenu is available.  
Remote control unit  
Projector  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Basic Menu Operation (Cont.)  
Basic Button Functions in the Menu Mode  
Button  
Function  
MENU  
Enters the main menu or exits the menu mode.  
Selects an item in the menu. Pressing or 5will scroll the item in the menu.  
Sets or adjusts the value.  
Cursor button 5/∞  
Cursor button 2/3  
PRESET  
If pressed while the keystone setting submenu is displayed, the value is set to “0”.  
Returns to the previous menu.  
EXIT  
ENTER  
Used to enter the submenu from the main menu.  
Used to enter the next submenu if “ENTER” is displayed in the selected item.  
Remote control unit  
Projector  
STAND BY  
LAMP  
TEMP  
QUICK  
ALIGN.  
OPERATE  
OPERATE  
HIDE  
W
HIDE  
SCREEN FREEZE  
COMP  
DVI  
VIDEO  
Y/C  
S
PC  
PC1  
PC2  
T
KEYSTONE  
PRESET  
T
ZOOM  
VIDEO  
MENU  
DIGITAL  
ZOOM  
FOCUS  
MENU  
KEYSTONE  
W
W
PRESET  
PRESET button  
EXIT button  
MENU button  
ENTER button  
MENU  
button  
PRESET  
button  
EXIT  
ENTER  
ENTER  
button  
EXIT  
button  
Cursor buttons  
5// 2/3  
EXIT  
ENTER  
RM-M160 REMOTE CONTROL UNIT  
Cursor buttons  
5// 2/3  
Video menu mode  
Video submenu  
Video main menu  
Menu  
Image adj.  
Contrast  
12  
Image adj.  
Set up  
3or  
Contrast  
Brightness  
Color  
ENTER  
Brightness  
Color  
12  
Color temp.  
Options  
12  
Tint  
Tint  
12  
Sharpness  
All reset  
Language  
Information  
Sharpness  
All reset  
1
EXIT  
ENTER  
Press 5/to select an item.  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
PC menu mode  
PC submenu  
PC main menu  
Menu  
Image adj.  
Contrast  
3or  
Image adj.  
Set up  
Brightness  
ENTER  
Contrast  
12  
12  
Sharpness  
All reset  
Color temp.  
Options  
Brightness  
Sharpness  
All reset  
1
2
3
4
5
Language  
Information  
EXIT  
ENTER  
Press 5/to select an item.  
Press 5/to select an item.  
Press 2/3to set or adjust the value.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                 
                                                                              
                                                                   
                                                                      
Menu Operations  
Changing the Color System (Video Menu Mode Only)  
This function is available only in Video menu mode.  
The menu is only displayed when there is a signal for the AV IN (Y/C, VIDEO and COMP) terminal.  
Normally, use the color system in AUTO. If operation in AUTO is unstable, such as color not being shown, set to a dedicated  
color system in accordance with the color system of the video signal being input.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Set up” with the cursor button 5or , and press 3 or the ENTER button.  
The “Set up 1” submenu appears on the screen.  
3 Select “Decoder” with the cursor button 5or , and press the ENTER button.  
The “Decoder” submenu appears on the screen.  
Video submenus  
Decoder  
Set up 1  
AUTO [ NTSC ]  
Position  
Gamma  
Aspect ratio  
Decoder  
Page 2  
ENTER  
NTSC  
Down  
Cinema  
4:3  
Up  
NTSC4.43  
PAL  
16:9  
ENTER  
EXIT  
ENTER  
ENTER  
SECAM  
4 Set the color system with the cursor button 5or .  
AUTO:  
Normally, set to “AUTO”. (Factory set value)  
The color system of a video signal being input is automatically identified and displayed in [ ].  
In [ ], B/W (Black & White), NTSC, NTSC4.43, PAL or SECAM will be displayed. (It is not always displayed.)  
For example, AUTO [ NTSC ] shows that the NTSC signal is being received.  
Dedicated to NTSC.  
NTSC:  
NTSC4.43:Dedicated to NTSC4.43.  
PAL: Dedicated to PAL.  
SECAM: Dedicated to SECAM.  
5 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                  
                                                                               
                                                                
                                                               
                                                                            
                                                                
                                                                             
                                                                          
                                                                                       
                                                                                            
Menu Operations  
Changing the Language Display  
The on-screen language is set to “English” when shipped from the factory. When you want to change to another language, set  
it as follows.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Language” with the cursor button 5or , and press 3or the ENTER button.  
The “Language” submenu appears on the screen.  
Language  
: Japanese  
English : English  
Deutsch : German  
Español : Spanish  
English  
Deutsch  
Español  
Italiano  
Français  
Italiano : Italian  
Français : French  
3 Set the language with the cursor button 5or .  
4 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
Note: for proper operation with the Video Processor and anamorphic lens,the projector  
should stay in the 4:3 mode. Aspect ratio control is operated with the projector.  
Memo  
About language display  
Some words in the menu and messages such as “Quick Alignment”, “Keystone”, “VIDEO” and “NTSC” are shown only in  
English.  
Changing the Screen aspect ratio/HDTV format (Video Menu  
Mode Only)  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Set up” with the cursor button 5or , and press 3 or the ENTER button.  
The “Set up 1” submenu appears on the screen.  
3 Select “Set up 2” with the cursor button 5or , and press 3 or the ENTER button.  
The “Set up 2” submenu appears on the screen.  
4 Select “Screen” or “HDTV” with the cursor button 5or .  
5 Adjust the Screen aspect ratio or HDTV format with the cursor button 2 or 3.  
To adjust multiple items, repeat 4 and 5.  
Adjustment item  
Screen  
HDTV  
Button  
Adjustment content  
Select according to the aspect ratio of the screen used.  
2or 3  
4:3  
16:9  
Set the number of effective scanning lines. Normally, select 1080i.  
2or 3  
1080i: 1035i:  
6 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                 
                                                                              
                                                                              
                                                                  
                                                                       
Menu Operations  
Adjusting Tracking/Phase  
Normally, tracking and phase adjustments are automatically carried out when a video signal is input to the projector for the  
first time, or when the QUICK ALIGN. button on the remote control is pressed.  
However, you can manually adjust the tracking and phase on the menu.  
If a wide stripe appears on the screen, adjust the lateral size of the picture image and the display area (tracking adjustment)  
so the stripe disappears.  
Also, if text projected on the screen appears flickers or appears dim, adjust phase adjustment so it becomes clear.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Set up” with the cursor button 5or , and press 3 or the ENTER button.  
The “Set up 1” (video mode) or “Set up” submenu appears on the screen.  
In video mode: Select set up 2 with the cursor or 5, and press ENTER button.  
The “Set up 2” submenu appears on the screen.  
Video submenu  
PC submenu  
Set up 1  
Set up 2  
Tracking  
Set up  
Tracking  
Position  
Gamma  
Aspect ratio  
Decoder  
Page 2  
ENTER  
Down  
123  
12  
123  
12  
Cinema Up  
4:3 16:9  
Phase  
Screen  
HDTV  
Page 1  
4:3  
16:9  
Phase  
Position  
Resize  
Clamp  
ENTER  
ENTER  
1030i  
1035i  
ENTER  
ENTER  
1:1  
ST  
Panel  
Aspect  
BP  
Decoder is only displayed when there is a signal for the AV  
IN terminal.  
3 Select “Tracking” or “Phase” with the cursor button 5or .  
4 Adjust the tracking or phase with the cursor 2or 3.  
Adjust the tracking and phase of the picture image being projected. To adjust the phase, first check for correct tracking  
adjustment.  
*To adjust multiple items, repeat 3 and 4.  
Adjustment item  
Tracking  
Phase  
Button  
2or 3  
2or 3  
Adjustment content  
The picture image shrinks laterally (right-to-left) or extends laterally (left-to-  
right). (–128 +127)  
Set to a position where text appears clear. (0 31)  
5 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
Note  
• A dim image could be caused by insufficient adjustment of brightness and contrast. Before adjusting phase, make sure that  
brightness and contrast are correctly adjusted. To adjust them, refer to “Adjusting Picture Quality” on page 49.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Set up for Watching Image Software (Video Menu Mode Only)  
This unit has a function which allows you to project movies, which were recorded on film, in the best possible conditions.  
(Function to convert 2-3 pull-down interlace scans to progressive scans)  
Normally use set to AUTO.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Set up” with the cursor button 5or , and press 3or the ENTER button.  
The “Set up 1” submenu appears on the screen.  
3 Select “Set up 2” with the cursor button 5or , and press 3or the ENTER button.  
The “Set up 2” submenu appears on the screen.  
4 Select “Deinterlace” with the cursor button 5or .  
5 Select the Deinterlace function mode with the cursor button 2or 3.  
Video: When watching images recorded with a video camera  
Film: When watching images recorded on film  
AUTO: The setting is changed automatically  
6 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
Note  
• Operates when the signal is an NTSC or PAL interlace signal. Does not operate for other signals. (The menu is not  
displayed when other signals are inputted.)  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                
                                                                    
                                                                                 
                                                                          
                                                                               
                                                       
                                                            
Menu Operations  
Adjusting Picture Quality  
In the “Image adj.” submenu, adjust brightness, contrast, sharpness, etc. to obtain the desired picture quality. Note that the  
adjustment items differ in Video menu mode and PC menu mode.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Image adj.” with the cursor button 5or , and press 3or the ENTER button.  
The “Image adj.” submenu appears on the screen.  
Video submenu  
PC submenu  
Image adj.  
Image adj.  
Contrast  
Contrast  
Brightness  
Color  
12  
12  
12  
12  
1
12  
12  
Brightness  
Sharpness  
All reset  
1
2
3
4
5
Tint  
ENTER  
Sharpness  
All reset  
ENTER  
3 Select the item to be adjusted with the cursor button 5 or .  
*“Color” and “Tint” are shown in Video submenu only.  
Note: Levels are pre-aligned at Faroudja.  
However, some fine-tuning for specific  
installations may be required.  
4 Make adjustment with the cursor 2 or 3.  
*To adjust multiple items, repeat 3 and 4.  
Adjustment item  
Contrast  
Button  
2or 3  
2or 3  
Adjustment content  
Gets lower/higher. (–30 0* +30)  
Brightness  
Color  
Gets darker/brighter. (–30 0* +30)  
Gets softer/deeper. (–30 0* +30)  
2or 3  
(Video menu mode only)  
Gets reddish/greenish. (–30 0* +30)  
(Video menu mode only)  
Tint  
2or 3  
Gets softer/sharper.  
• Video menu mode: (–5 0* +5)  
• PC menu mode: (1 3* 5)  
Sharpness  
2or 3  
Note  
• When in the PC menu mode, if the resize function in the PC submenu is set to  
“1:1”, the image quality will not change even if the value is changed.  
Resets above items to the factory set values. How to operate is mentioned below  
(next page).  
All reset  
ENTER  
* : Factory set value  
To perform All Reset  
• In the Image adj. submenu, select “All reset” with the cursor button 5or , and press the ENTER button. Then, the “All  
reset” submenu appears on the screen.  
• Press the cursor button 2to select “Yes”, and then press the ENTER button.  
• All items in the “Image adj.” submenu are reset to the factory set values and the menu returns to the previous one.  
To exit the “All reset” submenu without performing All reset, select “No” with the cursor button 3and, press the ENTER  
button.  
(To be continued on the next page)  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                               
                                                                    
                                                                                 
                                                               
                                                                    
                                                                       
                                                                            
                                                                                    
                                                                           
                                                                                
Menu Operations  
.
Image adj.  
All reset?  
Yes  
No  
5 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
Memo  
In some adjustments, the level bar changes according to the set value. (The setting value is also displayed at the left of the  
level bar.)  
Adjusting Color temperature  
Note: color temperature has been  
set by Faroudja.Do not readjust.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Color temp.” with the cursor button 5or , and press 3 or the ENTER  
button.  
The “Color temp.” submenu appears on the screen.  
3 Select “Color temp.” with the cursor button 5or .  
4 Adjust the color temperature with the cursor button 2or 3.  
Low:  
Middle:  
High:  
Color temperature decreases (image becoming reddish).  
Results in middle color temperature. (Factory set position).  
Color temperature increases (image becoming blueish).  
5 Select “RED” or “GREEN” or “BLUE” with the cursor button 5or .  
6 Fine adjust the color temperature with the cursor button 2 or 3.  
To adjust multiple items, repeat 5 and 6.  
Adjustment item  
RED  
Button  
2or 3  
2or 3  
2or 3  
Adjustment content  
Adjusts the red level. (0 to 255)  
GREEN  
BLUE  
Adjusts the green level. (0 to 255)  
Adjusts the blue level. (0 to 255)  
To perform All Reset  
• In the Color temp. submenu, select “All reset” with the cursor button 5or , and press the ENTER button. Then, the “All  
reset” submenu appears on the screen.  
• Press the cursor button 2to select “Yes”, and then press the ENTER button.  
• All items in the Color temp. submenu are reset to the factory set values and the menu returns to the previous one.  
To exit the “All reset” submenu without performing All reset, select “No” with the cursor button 3and, press the ENTER  
button  
7 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                            
                                                                 
                                                                              
                                                              
                                                                   
                                               
                                                 
                                                    
                                                         
Menu Operations  
Adjusting the Video Screen/Menu Position  
The position of the video screen and the menu on the video screen can be adjusted. You can finely adjust the video screen  
position. The menu will move widely on the video screen.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Set up” with the cursor button 5 or , and press 3 or the ENTER button.  
The “Set up 1” or “Set up” submenu appears on the screen.  
Video submenu (“Set up 1” submenu)  
PC submenu (Set up submenu)  
Set up  
Set up 1  
Tracking  
Phase  
123  
12  
Position  
Gamma  
Aspect ratio  
Decoder  
Page 2  
ENTER  
Down  
Cinema  
4:3  
Up  
Position  
Resize  
Clamp  
ENTER  
16:9  
1:1  
ST  
Panel  
Aspect  
BP  
ENTER  
ENTER  
Decoder is only displayed when there is a  
signal for the AV IN terminal.  
3 Select “Position” with the cursor button 5 or , and press the ENTER button.  
The “Position” submenu appears on the screen.  
Position  
Disp.Posi.  
12,12  
Menu  
ENTER  
Horizontal position  
Vertical position  
4 Press the ENTER button to select “Disp.Posi.” or “Menu”.  
Disp.Posi. (Display Position):The video screen position (display position) can be adjusted.  
Menu:The menu position can be adjusted.  
5 Press the cursor button 5, , 2 or 3 to move the video screen (display) or the  
menu.  
*Repeat 4 and 5 to move both video screen (display) and menu positions.  
Adjustment item  
Disp.Posi. - H  
Disp.Posi. - V  
Menu - H  
Button  
2or 3  
5or ∞  
2or 3  
5or ∞  
Adjustment content  
The video screen moves to the left or right. (–30 +30)  
The video screen moves up or down. (–30 +30)  
The menu moves to the left or right. (Left, center*, right)  
The menu moves up or down. (Top, center*, bottom)  
Menu - V  
* : Factory set value  
6 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                          
                                                               
                                                                            
                                                                            
                                                                                 
                                                                        
                                                                             
Menu Operations  
Changing the Image Gamma/Aspect Ratio (Video Menu Mode Only)  
The image Gamma (Down, Cinema or Up) and the aspect ratio (4:3 or 16:9) are selectable in Video menu mode.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Set up” with the cursor button 5 or , and press 3 or the ENTER button.  
The “Set up 1” submenu appears on the screen.  
Video submenu  
Set up 1  
Position  
Gamma  
Aspect ratio  
Decoder  
Page 2  
ENTER  
Down  
Cinema  
4:3  
Up  
16:9  
ENTER  
ENTER  
Decoder is only displayed when there is a signal for the Video IN terminal.  
3 Select “Gamma” or “Aspect ratio” with the cursor button 5 or .  
4 Adjust the image tone or aspect ratio with the cursor 2 or 3.  
*To adjust multiple items, repeat 3 and 4.  
Adjustment item  
Button  
Adjustment content  
The image Gamma projected on the screen can be changed.  
Down  
: Suitable for projecting the video programs.  
Gamma  
2or 3  
Cinema* : Normally use in this mode.  
Up  
: Suitable for projecting the cinema programs.  
Sets the vertical-to-horizontal ratio (4:3 or 16:9) of the video image projected.  
“4:3*” : The aspect ratio of the projected image becomes 4:3. Set it to 4:3 for video  
of NTSC, NTSC4.43, PAL, SECAM.  
Aspect ratio  
2or 3  
“16:9” : The aspect ratio of projected image becomes 16:9. Set it to 16:9 for Hi-  
Vision devices (W-VHS VCR, etc.).  
* : Factory set value  
5 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                                  
                                                                       
                                                                                    
                                                                  
                                                                       
                                                                                        
                                                                                             
                                                                  
                                                                       
                                                                                    
                                                                  
                                                                       
                                                                         
                                                                              
Menu Operations  
Changing the Image Size - Resize Function (PC Menu Mode Only)  
The picture image projected can be selectable with the  
Resize function which is available only in PC menu mode.  
You can choose the video image size projected from the  
1 Press the MENU button.  
The main menu appears on the screen.  
following: (Factory setting is “Aspect”.)  
2 Select “Set up” with the cursor button  
5 or , and press 3 or the ENTER  
“1:1”: The image is displayed at the input resolution. The  
button.  
picture image projected is not enlarged even if its  
number of pixels (resolution) is smaller than that of  
the projector’s D-ILA element (1365 pixels × 1024  
pixels).  
The “Set up” submenu appears on the screen.  
PC submenu  
Resize: 1:1  
Set up  
Tracking  
123  
12  
Full size (1365 × 1024)  
Phase  
Position  
Resize  
Clamp  
ENTER  
1:1  
ST  
Panel  
Aspect  
BP  
Image not enlarged  
3 Select “Resize” with the cursor button  
Panel: The picture image projected is virtually enlarged to  
the full size (1365 pixels × 1024 pixels). The  
horizontal and vertical enlargement ratio will differ  
depending on the original image and the image will  
be deformed.  
5 or .  
4 Choose “1:1”, “Panel”, or “Aspect”  
with the cursor button 2 or 3.  
Resize: Panel  
5 Press the EXIT button to return to the  
previous menu or press the MENU  
button to exit the menu mode.  
Image enlarged  
to the full size  
(1365 × 1024)  
Changing the Clamp pulse position  
(PC Menu Mode Only)  
When the image is too dark or bright, or when the image is  
unstable, switching the position may improve the image  
quality. Normally, set to “BP”.  
Image not enlarged  
(Original image)  
Aspect:While maintaining the original aspect ratio, the video  
image projected is virtually enlarged until either the  
horizontal or vertical side reaches the full size (1365  
pixels × 1024 pixels).  
1 Press the MENU button.  
The main menu appears on the screen.  
Resize: Aspect  
Image enlarged to the aspect size.  
(Example: aspect ratio is 16:9)  
2 Select “Set up” with the cursor button  
5 or , and press 3 or the ENTER  
button.  
Full size (1365 × 1024)  
The “Set up” submenu appears on the screen.  
3 Select “Clamp” with the cursor button  
5 or .  
Image not enlarged (original image)  
(Example: aspect ratio is 16:9)  
4 Choose “ST” or “BP” with the cursor  
button 2or 3.  
Image enlarged to the aspect size.  
(Example: aspect ratio is 5:4)  
5 Press the EXIT button to return to the  
previous menu or press the MENU  
button to exit the menu mode.  
Full size (1365 × 1024)  
ST: Sync Tip BP: Back Porch  
Image not enlarged  
(original image)  
(Example: aspect ratio is 5:4)  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                           
                                                                
                                                                             
                                                                        
                                                                            
                                                     
                                                          
Menu Operations  
Setting and Adjusting Other Functions (OPTIONS)  
Various functions are provided as shown in the “Options 1” and “Options 2” submenus.  
You can set or adjust each function, as required.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Options” with the cursor button 5 or , and press 3 or the ENTER button.  
The “Options 1” submenu appears on the screen.  
Options 1  
Menu display  
Line display  
Lamp time display  
Keystone  
15sec  
5sec  
ON  
ON  
OFF  
OFF  
ENTER  
ENTER  
Lamp control  
Page 2  
ENTER  
3 Select the item to be adjusted with the cursor button 5 or .  
4 Make adjustment with the cursor 2 or 3.  
• While the keystone item is selected, press the ENTER button to display the “Keystone” submenu.  
• To enter the “Page 2” submenu, select “Page 2” with the cursor button 5or , and press the ENTER button.  
• To return to the “Page 1” submenu from the “Page 2” submenu, select “Page 1” with the cursor button 5or , and press  
the ENTER button.  
Keystone  
123  
Options  
ENTER  
Lamp control  
Menu display  
Line display  
Lamp time display  
Keystone  
15sec  
5sec  
ON  
ON  
OFF  
OFF  
Normal  
LPC  
LOC  
ENTER  
ENTER  
ENTER  
Lamp control  
Page 2  
ENTER  
ENTER  
ENTER  
ENTER  
Page 2  
Flip H  
OFF  
OFF  
9600  
30  
ON  
ON  
Flip V  
RS-232C [bps]  
Sleep time [min]  
Page 1  
19200  
60 OFF  
15  
ENTER  
*To adjust multiple items, repeat 3 to 4.  
*To reset the keystone (trapezoidal distortion of the picture image) to the original setting, press the PRESET button when  
the “Keystone” submenu appears on the screen.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Operations  
Adjustment item  
Button  
Adjustment content  
Sets whether to clear the menu display automatically or not.  
15sec* : Clears the display automatically in about 15 seconds.  
Menu display  
2or 3  
ON  
: Does not automatically clear the menu display.  
Sets whether to show the line display (Y/C, VIDEO, COMP, PC1, PC2 or DVI) on top  
right of the screen or not when the VIDEO or PC button is pressed.  
5sec* : Shows the line display for about 5 seconds.  
Line display  
2or 3  
OFF : Does not show the line display.  
Displays the lamp use time.  
ON* : Displays when the lamp use time reaches 1000 hours when set in the LPC or  
Lamp time display  
2or 3  
LOC mode.  
OFF : Does not display when the lamp use time reaches 1000 hours when set in the  
LPC or LOC mode.3  
Press the ENTER button to enter the keystone submenu.  
In the keystone submenu, press 2or 3to correct trapezoidal distortion of the  
projected image. (–80 0* +128)  
To reset the keystone (trapezoidal distortion of the picture image) to the original  
setting (factory set value: 0), press the PRESET button when the “Keystone”  
submenu appears on the screen.  
Keystone  
ENTER  
To exit the keystone submenu, press the EXIT button.  
Press ENTER to enter the lamp control submenu.  
Normal* : Used as a normal lamp.  
LPC  
: Automatically controls the power used by the lamp and increases it in  
steps. When this mode is used, the brightness starts at approximately  
70%. The decrease in brightness is slower than in “Normal” mode and this  
mode is best suited when using the projector continuously for long periods  
of time.  
Lamp control  
ENTER  
* “Lamp replacement” appears on the screen when the lamp use time  
exceeds 2000 hours.  
LOC  
: The brightness can be set in seven levels (-6 to 0). Since the brightness  
can be set in steps, this is the mode best suited for adjusting multiple  
screens. This setting can also be changed while the projector is being  
used. To change the setting, choose LOC with the 5/cursors and  
choose the level with the 2/3cursors.  
Reverses image right-to-left.  
Flip H  
2or 3  
OFF* : For the front method.  
ON : For upside-down hanging from the ceiling.  
Inverses image upside-down.  
Flip V  
2or 3  
OFF* : For normal setup.  
ON : For upside-down hanging from the ceiling.  
Sets the baud rate for transmission.  
RS-232C [bps]  
2or 3  
9600  
: 9600 bps  
19200* : 19200 bps  
Sets the length of sleep time which automatically brings the projector into stand-by  
state. You can select one of the sleep times: 15, 30, 60 and 0 (OFF*) minutes.  
Sleep time [min]  
2or 3  
* Factory set value  
5 Press the EXIT button to return to the previous menu or press the MENU button to  
exit the menu mode.  
Note  
• Refer to “Removing the Trapezoidal Distortion of the Image” on page 35 for more details about adjusting the keystone.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                                               
                                                                    
Menu Operations  
Getting Information  
You can get information on the input signal, accumulated used hours of light-source lamp, etc.  
1 Press the MENU button.  
The main menu appears on the screen.  
2 Select “Information” with the cursor button 5 or .  
The “Information” will be displayed in the main menu.  
*No submenu can be selected.  
Video main menu  
PC main menu  
Menu  
Menu  
Image adj.  
Setting  
Image adj.  
Setting  
Input  
VIDEO  
CH.0  
Input  
PC 1  
CH.0  
Switcher  
Source  
Switcher  
Color temp.  
Options  
Color temp.  
Options  
NTSC  
Resolution 1280 1024  
Frequency H  
Frequency V  
Lamp time  
79.9 kHz  
75 Hz  
Language  
Information  
Language  
Information  
Lamp time  
123 h  
123 h  
Input:  
Switcher:  
Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO or COMP, or PC1, PC2 or DVI)  
This display currently has no meaning. This is reserved for future use. (“CH.0” is usually displayed to  
indicate that it is not being used.)  
Source:  
Resolution:  
Shows the projected image’s type of video signal. (Video menu mode)  
Shows the resolution of the video signal being received. (PC menu mode)  
It may not be displayed correctly with some input signals.  
Frequency H:  
Frequency V:  
Lamp time:  
Shows the horizontal frequency of the video signal being received. (PC menu mode)  
Shows the vertical frequency of the video signal being received. (PC menu mode)  
Accumulated used hours of the light-source lamp.  
3 Press the MENU button to exit the menu mode.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the Fuse  
A fuse is used to protect the power source of the projector. If the fuse is blown, replace it. When the power switch is turned on  
but no power is supplied to the projector, check the fuse. If there are any unclear points, contact the dealer where you  
purchased your projector, or consult the Service center.  
CAUTION  
• When replacing the fuse, use the same rating and type (12 A 250 V). Otherwise, a fire may occur and/or the projector may  
be damaged.  
1 Turn off the main power switch and  
disconnect the power cord from both  
the projector and the wall outlet.  
In stand-by state (the STAND BY indicator lights on),  
place the MAIN POWER switch of OFF [ ] position.  
2 Loosen the fuse holder to remove it.  
To loosen the fuse holder, use a Phillips screwdriver.  
Fuse holder  
Phillips screwdriver  
3 Remove the fuse from the fuse holder  
Fuse (12 A, 250 V)  
you just removed.  
4 Install the new fuse (not supplied) into  
Fuse holder  
the fuse holder.  
5 Reinstall the fuse holder into the  
Fuse (12 A, 250 V)  
projector.  
To reinstall the fuse holder, use a Phillips screwdriver.  
Fuse holder  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the Light-Source Lamp  
Light-source lamp and lamp use time  
The light-source lamp has a service life of approximately 1000 hours.  
[Average lamp life: 1000 hours (brightness half-life)]  
When the light-source lamp approaches the end of its service life, degradation progresses rapidly. In NORMAL MODE,  
arrange for a new lamp (lamp unit) or replace the lamp after 900 hours. Depending on the usage conditions, the replacement  
time may be shorter.  
(In LOC and LPC modes, the brightness of the lamp is electrically controlled and the replacement time is extended. Arrange  
for a new lamp (lamp unit) or replace the lamp after 1900 hours. Depending on the usage conditions, the replacement time  
may be shorter.)  
If, even after adjusting the brightness or color, the video image is dark or the color is not correct, replace the lamp early.  
The lamp use time can be checked. Look at the “Lamp time” which is displayed with the “Information” option in the menu.  
(Refer to page 40, 42.)  
Contact the store from where you purchased the projector or the JVC service center for details about purchasing  
replacement lamps.  
Replacement lamp (lamp unit) part number: BHL 5001-SU  
The LAMP indicator and the message on the screen warn you that replacement of the lamp is required, as follows:  
Projecting after the lamp has been used for more than 900 hours (NORMAL MODE)  
Accumulated used hours  
of the light-source lamp  
When the lamp use time reaches 900 hours:  
The LAMP indicator lights on the projector.  
900 hours  
When starting to project after 900 hours has been exceeded:  
“Lamp replacement” appears on the screen.  
* The message will disappear when any button is pressed.  
When the lamp use time exceeds 1000 hours:  
The LAMP indicator blinks on the projector.  
Lamp replacement  
EXIT  
“Lamp replacement” appears on the screen and the word “Warning”  
blinks.  
1000 hours  
* To cancel this message, press the EXIT button.  
However, the same message will appear every hour.  
* If the projector is put in stand-by mode or turned off after the lamp has  
been used for more than 1000 hours (but less than 2010 hours), it can  
not be turned back on again unless the light-source lamp is replaced  
with a new one.  
Warning  
Lamp replacement  
EXIT  
Replace with a new lamp (lamp unit) and reset the lamp time. (Refer  
to page 62.)  
When the lamp use time reaches 1010 hours:  
The projector is forcibly turned off.  
The LAMP and OPERATE indicators blinks on the projector.  
* The projector can not be turned on unless the lamp (lamp unit) is  
replaced with a new one and the lamp time is reset. (Refer to  
page 62.)  
1010 hours  
Note  
• If the projector is not put in stand-by mode or turned off, it can be used until 2010 hours is reached.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the Light-Source Lamp  
Projecting after the lamp has been used for more than 1000 hours (LIGHT OUTPUT  
CONTROL MODE) (LAMP POWER CONTROL MODE)  
Accumulated used hours  
of the light-source lamp  
When the lamp use time reaches 1000 hours:  
1000 hours  
“1000h” and “Lamp replacement” appear on the screen.  
* The messages will disappear when any button is pressed.  
* The time after which the display appears can be set with the OSD  
menu.  
1000 h  
Lamp replacement  
EXIT  
When the lamp use time exceeds 1900 hours:  
The LAMP indicator blinks on the projector.  
“Lamp replacement” appears on the screen.  
* To cancel this message, press the EXIT button or display another  
menu.  
Every time the projector is turned on, the message appears.  
When the lamp use time exceeds 2000 hours:  
The LAMP indicator blinks on the projector.  
1900 hours  
2000 hours  
2010 hours  
Lamp replacement  
EXIT  
“Lamp replacement” appears on the screen and the word “Warning”  
blinks.  
* To cancel this message, press the EXIT button.  
However, the same message will appear every hour.  
* If the projector is put in stand-by mode or turned off after the lamp has  
been used for more than 2000 hours, it can not be turned back on  
again unless the light-source lamp is replaced with a new one.  
(If the projector is not put in stand-by mode or turned off, it can be  
used until 2010 hours is reached.)  
Warning  
Lamp replacement  
EXIT  
Replace with a new lamp (lamp unit) and reset the lamp time. (Refer  
to page 62.)  
When the lamp use time reaches 2010 hours:  
The projector is forcibly turned off.  
The LAMP and OPERATE indicators blinks on the projector.  
* The projector can not be turned on unless the lamp (lamp unit) is  
replaced with a new one and the lamp time is reset. (Refer to  
page 62.)  
CAUTIONS  
• If the projector is set up in a constricted place which is unsuitable for work, and if you perform replacement work there, this  
could cause injury. Move the projector to a place large enough for work, and then replace the light-source lamp.  
• Use a genuine product for the light-source lamp. If you use other than a genuine product, this could cause a malfunction.  
Also, never use an old light-source lamp. This could cause marked degradation in performance or explode, possibly causing  
the projector to malfunction or broken pieces to injure you.  
• Do not replace the light-source lamp immediately after the projector has been used. The temperature of the light-source  
lamp is still high and could cause a burn. Allow a cooling period of one hour or more before performing replacement.  
• Before starting light-source lamp replacement work, turn off the MAIN POWER switch, and disconnect the power cord from  
the wall outlet. If you perform the replacement work with the power cord connected, this could cause injury or electric shock.  
• The light-source lamp used in this projector is a high pressure mercury lamp. Be careful when disposing of the light-source  
lamp. If anything is unclear, please consult your dealer.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the Light-Source Lamp  
Be sure that the power cord is unplugged from the wall outlet.  
1 Remove the lamp-replacement opening  
cover by loosening screws.  
Loosen the two screws with a flat-end screwdriver.  
Screw  
Note  
• The screws are fitted so that they do not come off the lamp-  
replacement opening cover.  
Lamp-replacement  
opening cover  
Be careful not to damage  
the claw.  
2 Loosen the screws, raise the handle,  
and pull out the light-source lamp.  
Loosen the two screws with a flat-end screwdriver.  
Screw  
Note  
• The screws are fitted so that they do not come off the light-  
source lamp.  
Light-source lamp  
Handle  
(To be continued on the next page)  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the Light-Source Lamp  
3 Insert the new light-source lamp fully  
Light-source lamp  
inside and fasten the screws.  
Fasten the two screws with a flat-end screwdriver.  
CAUTION  
• Do not touch the glass surface of the light-source lamp  
directly with your hand as well as staining it. If you touch  
with a bare hand, oils and other substances on your hand  
may adhere to the lamp, possibly preventing it from  
performing as specified and therefore giving a shortened  
lamp life, a darkened screen, etc. To handle a new light-  
source lamp, hold it by the plastic part. Never touch the  
metal part or the front glass surface.  
Handle  
Screw  
4 Replace the lamp-replacement opening  
Lamp-replacement  
opening cover  
cover and fasten the screws.  
Fasten the two screws with a flat-end screwdriver.  
CAUTIONS  
• Install the light-source lamp and close the lamp-  
replacement opening cover correctly; otherwise, a safety  
switch is activated to prevent the projector from operating.  
• If the claw on the lamp-replacement opening cover is  
damaged, the projector may not possibly operate. Then,  
replace with a new lamp-replacement opening cover.  
Be careful not to  
damage the claw.  
5 Reset the lamp use time.  
Perform “Resetting the Lamp Use Time” on page 62.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacing the Light-Source Lamp  
Resetting the Lamp Use Time  
After replacing with a new light-source lamp, reset the lamp-time counter inside the projector to clear the accumulated lamp  
time to zero (0). After resetting, a new count will start for the new light-source lamp.  
1 Turn on the MAIN POWER switch to go  
Projector’s button  
into stand-by mode.  
In stand-by mode, the STAND BY indicator on the  
projector lights up.  
STAND BY  
indicator  
STAND BY  
OPERATE  
LAMP  
TEMP  
OPERATE  
indicator  
2 Press the following buttons on the  
HIDE  
4 HIDE  
projector, sequentially.  
button  
PC  
1 PC  
1 Momentary press the PC button.  
KEYSTONE  
PRESET  
button  
VIDEO  
MENU  
2 Momentary press the ENTER button.  
3 Momentary press the EXIT button.  
4 Press and hold the HIDE button for two seconds  
MENU  
button  
2 ENTER  
3
EXIT  
button  
or more.  
EXIT  
ENTER  
button  
* During this sequence, the STAND BY and OPERATE  
indicators alternately blink about every approx. 3 seconds.  
After completion of the sequence, the STAND BY indicator  
alone stays on.  
Cursor buttons 5/∞  
* Buttons must be pressed within 2 seconds of the previous  
button.  
* When you make a mistake in button operations, return to  
the beginning of the sequence.  
* To check the lamp time on the menu, press the MENU button  
and select “Information” with the cursor button 5or ∞  
.
The lamp use time is indicated in the item “Lamp time”.  
Video main menu  
Menu  
Image adj.  
Input  
VIDEO  
CH.0  
Setting  
Switcher  
Source  
Color temp.  
Options  
NTSC  
Language  
Information  
Lamp time  
123 h  
Lamp time (0 h)  
PC main menu  
Menu  
Image adj.  
Setting  
Input  
PC 1  
CH.0  
Switcher  
Color temp.  
Options  
Resolution 1280 1024  
Frequency H  
Frequency V  
Lamp time  
79.9 kHz  
75 Hz  
Language  
Information  
123 h  
Lamp time (0 h)  
CAUTION  
• Reset the lamp use time only when you have replaced with  
a new light-source lamp. Never reset it during lamp life,  
otherwise the replacement time may become unclear, and  
lead to degraded performance or lamp explosion.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning and Replacing the Filter Cover  
Clean the filter regularly. If the filter is heavily stained and does not clean, or if it is damaged, replace the filter with a new filter.  
Otherwise, dirt may get inside and appear on the screen, preventing you from fully enjoying the video image. If dirt gets inside  
or if you need information about the filter, consult authorized dealer where you purchased the projector or the nearest Service  
Center.  
1 Turn off the MAIN POWER switch.  
After the projector goes into stand-by state with the STAND BY indicator on, turn off the MAIN POWER switch and pull  
out the power cord from the projector and the wall outlet.  
2 Remove the filter.  
Loosen the screw with a flat-end screwdriver.  
Screw  
Filter  
Be careful not to  
damage the claws.  
Notes  
• The screw is fitted so that it does not come off the filter.  
• If the filter is clogged with dirt, etc., the projector goes into an warning state (the OPERATE and STAND BY indicator blink.  
etc.). Therefore regularly, clean the filter. For the warning indication, refer to page 67.  
3 Clean the filter.  
Clean the filter with a neutral detergent, wash it in water, and then dry it in the shade.  
CAUTIONS  
• Put on rubber gloves when using neutral detergent.  
• After you have washed the filter in water, make sure the filter is completely dry before reinstalling it, otherwise an electric  
shock or malfunction could occur.  
• Do not clean the filter using a vacuum cleaner. Since the filter is soft, it may be sucked into the vacuum cleaner or damaged.  
4 Reinstall the filter.  
Fasten the screw with a flat-end screwdriver.  
Notes  
• Install the filter correctly. Otherwise, the projector does not operate. (Goes into an warning state (For the warning indication,  
Refer to page 66).)  
• If the filter’s claws (in particular the claw which is hidden behind the filter cover knob) are damaged, the projector may not  
operate. Then, replace with a new filter.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Solutions to common problems related to your projector are described here. If none of the solutions presented here solves the  
problem, unplug the projector and consult an authorized dealer or Service Center.  
Symptom  
Power is not  
supplied.  
Probable cause  
Corrective action  
Page  
30  
Is the power cord disconnected?  
Insert the power cord (plug) firmly.  
Turn on the MAIN POWER switch.  
Is the MAIN POWER switch turned  
on?  
32  
Is the fuse blown?  
Turn off the MAIN POWER switch and  
check the fuse.  
If it is blown, replace it  
57  
Is the lamp-replacement opening cover • Turn off the MAIN POWER switch, close  
7, 32, 60  
closed correctly?  
the lamp-replacement opening cover  
correctly, and turn on the MAIN POWER  
switch again.  
Is the filter closed correctly?  
Turn off the MAIN POWER switch, fit the  
filter correctly, and turn on the MAIN  
POWER switch again.  
7, 32, 63  
Has the lamp life expired? (Has the  
lamp use time reached 1000 hours in  
the normal mode?)  
• Turn off the MAIN POWER switch, replace 32, 58,  
with a new light-source lamp, and turn on  
the MAIN POWER switch.  
59, 62  
(Has the lamp use time reached 2000  
hours in the LPC or LOC mode?)  
Reset the lamp use time after replacing with  
a new lamp.  
Light is not emitted,  
or light level is low.  
Is the lens cap removed?  
Remove the lens cap.  
30  
Is the lamp life near its end?  
Check the lamp use time on the menu, and 56, 58,  
if the lamp life is near its end, arrange for a  
replacement lamp, or replace a little earlier.  
59  
With power on,  
operation starts but  
stops in a few  
minutes.  
Is the air intake or exhaust area  
blocked?  
Turn off the MAIN POWER switch, remove 6, 7, 32  
any blocking objects, and turn on the MAIN  
POWER switch again.  
Video image does not • Is the correct input selected?  
appear.  
Select the correct input with the VIDEO and  
PC buttons.  
9, 13  
Are devices connected correctly?  
Connect devices correctly.  
11, 22  
Are signals being supplied from the  
connected devices?  
Set connected devices correctly.  
Are input signals (scanning frequency, • Check if the signal is appropriate (scanning 22, 23  
etc.) appropriate?  
frequency, etc.) and input the appropriate  
signal.  
Is the correct color system selected?  
Is brightness adjusted correctly?  
Set the color system to AUTO or to the  
correct dedicated color system.  
45  
49  
Adjust brightness on the menu.  
Is video turned off by pressing the  
HIDE button?  
Press the HIDE button to turn video on.  
10, 12,  
35  
During DVI input, are image signals  
output from the computer graphic  
board (DVI output terminal)?  
(During DVI input, depending on the  
computer settings, there may be no  
signal input or an error may occur (blue  
screen).)  
If this happens, turn off the power to both  
the projector and the computer, and then  
turn the projector back on before turning the  
computer on again. Then correctly set the  
computer’s graphic board.  
22  
Video image dims.  
Is focus adjusted correctly?  
Adjust focus.  
12, 34  
Is distance too short or too long?  
Set the projector at the correct distance.  
18, 76,  
77  
Are Tracking and Phase adjusted  
correctly?  
If satisfactory results are not obtained by  
pressing the QUICK ALIGN. button to  
conduct quick alignment, adjust Tracking  
and Phase on the menu.  
13, 36,  
47  
Video image is  
abnormally dark or  
bright.  
Is picture quality (Brightness, etc.)  
adjusted correctly?  
Adjust picture quality on the menu.  
49  
Video image freezes.  
Was the FREEZE button on the  
remote control pressed?  
Press the FREEZE button to release  
freezing.  
12, 37  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Symptom  
Probable cause  
Corrective action  
Page  
A part of image is  
magnified.  
Was the DIGITAL ZOOM T button on  
the remote control pressed?  
Press the PRESET button to restore the  
original video screen.  
12, 37  
Color is poor or  
unstable.  
Is picture quality (color density, etc.)  
adjusted correctly?  
Adjust picture quality on the menu.  
49  
Is the correct color system selected?  
Set the color system to AUTO or to the  
correct dedicated color system.  
45  
Are signals (scanning frequency, etc.)  
of the connected devices appropriate?  
Check if the signal is appropriate (scanning  
frequency, etc.), and input the appropriate  
signal.  
22  
The upper part of the  
video image bows or  
distorts.  
While computer system signal is input, • Input separate sync signals for vertical sync 11, 28  
isn’t a sync signal for composite sync  
(Cs) or G on sync being input?  
(V) and horizontal sync (H) signals.  
Isn’t signal with much jitter or skew  
distortion being input from a video  
deck?  
Input signals with little jitter or distortion.  
Use a TBC or a device with a built-in TBC.  
Video image  
suddenly go out.  
Is video picture turned off by pressing  
the HIDE button?  
Turn on video picture by pressing the HIDE 10, 12,  
button.  
35  
Remote control unit  
does not work.  
Are batteries installed correctly?  
Match the polarities of batteries correctly (+  
to + and – to –).  
14  
Are batteries exhausted?  
Replace with new batteries.  
14  
20  
Is there a shielding object between the • Remove any shielding objects.  
remote control unit and the remote  
sensor?  
Is the distance too long?  
Use the remote control unit at a nearer  
point.  
20  
21  
Is either side of remote cable  
disconnected?  
Firmly insert the remote cable when using  
the remote control unit as the wired one.  
* This device uses a computer. External noise may cause it to malfunction. If this happens, turn the power off, remove the  
electric plug from the wall outlet. Then insert the electric plug back into the wall outlet, turn the power back on and check the  
operation.  
When warning indication is shown by the blinking indicators:  
The warning status will be notified by the combination lighting of the projector’s indicators.  
For the warning contents and the action to be taken, refer to “Warning Indication” on page 66.  
Maintenance  
• Stains on the cabinet  
These should be wiped off with a soft cloth. If the cabinet is heavily stained, wipe it with a cloth soaked in water-diluted  
neutral detergent and wring well, then wipe clean with a dry cloth.  
• Since the cabinet may deteriorate in quality, become damaged, or show paint peeled, note the following:  
– Do not wipe with rough cloth.  
– Do not wipe vigorously.  
– Do not wipe with thinner or benzene.  
– Do not apply any volatile substance such as insecticides.  
– Do not allow any rubber or vinyl article to remain in contact with the cabinet for a long time.  
• Stains on the lens  
These should be cleaned off with commercially available lens blowers or lens cleaning paper (for cleaning glasses and  
cameras).  
Do not use liquid cleaning agents. This could cause the surface coating to be removed.  
Do not rub, scratch or hit the lens as its surface is prone to damage.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning Indication  
If something abnormal has occurred with the projector, the warning status will be indicated by the combination of lighting the  
indicators on the control panel as shown in the following table. Then, the projector automatically stops projection and runs the  
cooling fan for about 120 seconds.  
Warning indication table:  
Indicator  
No.  
Warning content  
LAMP  
Blink  
TEMP  
STAND BY  
OPERATE  
1
2
Blink  
The light-source lamp does not light and projection  
is not made.  
Blink  
Blink  
Blink  
The light-source lamp has suddenly gone off during  
projecting an image.  
3
4
5
6
7
Blink  
Circuit operation is abnormal.  
Blink  
Blink  
Blink  
The filter is displaced.  
Blink  
Blink  
Blink  
The internal temperature is too high. (Sensor 1)  
The internal temperature is too high. (Sensor 2)  
The cooling fan has stopped (locked).  
Blink  
Blink  
Blink  
* For individual indicator lighting, refer to page 58.  
Action to be taken for warning indication  
Stopping the projector:  
After the cooling fan has stopped, take the following action.  
No. 1  
No. 2  
No. 3  
: Check that the cover for replacing the light-source lamp and the front panel are securely attached, and then, press  
the OPERATE button for one second or more to turn on the projector for retrying.  
: Check that the cover for replacing the light-source lamp and the front panel are securely attached, and then, press  
the OPERATE button for one second or more to turn on the projector for retrying.  
: Press the OPERATE button for one second or more to turn on the projector for retrying.  
Nos. 4-7 : Follow the next steps.  
1. Turn off the MAIN POWER switch and unplug the power cord from the wall outlet.  
2. Take an action according to the number.  
No. 4  
No. 5  
No. 6  
No. 7  
: Set the filter in place.Then, leave the projector until it cools down.  
: Check that nothing is blocking the air inlet nor outlet, and wait until the inside cools down.  
: Check that nothing is blocking the air inlet nor outlet, and wait until the inside cools down.  
: Leave the projector until it cools down.  
3. Plug in the power cord again, turn on the MAIN POWER switch, and press the OPERATE button for one second or  
more to turn on the projector for retrying.  
Retrying operation:  
Plug in the power cord again and operate the projector.  
If the same warning indication is observed again, after the cooling fan has stopped, turn off the MAIN POWER switch, unplug  
the power cord, and call your dealer for repair.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning Messages  
The following shows the warning messages that can be displayed on the screen. When a warning message is displayed, take  
the corrective action described here.  
Message  
Cause  
Corrective action  
Page  
No device is connected to the  
input terminal.  
The terminal is connected but no  
signal is output from the  
connected device.  
Connect a device to the selected  
terminal.  
Operate the connected device  
and output a signal.  
9, 11,  
24 ~ 29,  
33  
PC 1  
* The selected input mode (input  
terminal) name is shown in the  
first line of the massage.  
No Input  
The frequency of the input video  
signal is out of range.  
The selected input mode (input  
terminal) name is shown in the  
first line of the message.  
Input the video signals whose  
frequency is within the projector’s  
specifications.  
22, 23,  
70  
PC 1  
Frequency of input signal is out of range.  
Though the frequency of the input • Input the video signals that  
22, 23,  
70  
video signal is within the  
satisfies the projector’s  
specifications.  
acceptable range, other items  
such as resolution are out of the  
projector’s specifications.  
PC 1  
The selected input mode (input  
terminal) name is shown in the  
first line of the message.  
Signal is not supported.  
When the FREEZE button is  
pressed, this message appears  
for a few seconds.  
When a button not acceptable is  
pressed during freezing, this  
message appears for a few  
seconds to notify that the image is  
being frozen.  
To release freezing, press the  
FREEZE button on the remote  
control.  
12, 37  
FREEZE  
When the FREEZE button is  
pressed for the video signals that  
cannot be frozen (UXGA 60Hz,  
SXGA 60Hz.), this message  
appears for a few seconds to  
notify that the image cannot be  
frozen.  
Freeze function does not work for 12, 37  
the inputted video signals.  
To use this function, input the  
video signals that can be frozen.  
FREEZE  
* To forcibly clear the message,  
press the EXIT button.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning Messages  
Message  
Cause  
Corrective action  
Page  
When the DIGITAL ZOOM button • Digital-zoom function does not  
13, 37  
is pressed for the video signals  
that cannot be zoomed (UXGA  
60Hz, SXGA 60Hz.), this  
message appears for a few  
seconds to notify that the image  
cannot be digitally zoomed.  
work for the inputted video  
signals.  
To use the this function, input the  
video signals that can be digitally  
zoomed.  
D.ZOOM  
* To forcibly clear the message,  
press the EXIT button.  
Displayed when the lamp control  
setting is set to NORMAL MODE  
Arrange for a new lamp (lamp  
unit) or replace the lamp early.  
44, 46  
Appears every time the projector  
is turned on after the lamp use  
time has exceeded 900 hours and  
until it reaches 1000 hours.  
Lamp replacement  
EXIT  
* The message is cleared by  
pressing any button.  
Displayed when the lamp control  
setting is set to NORMAL MODE  
Replace with a new lamp (lamp  
unit) and reset the lamp time.  
44, 46  
When the lamp use time reaches  
1000 hours, the word “Warning”  
blinks on the screen.  
Warning  
* To cancel this message, press  
the EXIT button.  
Lamp replacement  
EXIT  
However, the same message will  
appear every hour.  
* If the power is turned off after the  
lamp use time has exceeded  
1000 hours, the power can not be  
turned on again.  
* When the lamp use time reaches  
1010 hours, the projector is  
forcibly turned off and can not be  
turned back on again.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning Messages  
Message  
Cause  
Corrective action  
Page  
Displayed when the lamp control  
setting is set to LIGHT OUTPUT  
CONTROL MODE (LOC) or LIGHT  
POWER CONTROL MODE (LPC)  
and the lamp use time display is  
turned [ON] with the OSD menu  
Arrange for a new lamp (lamp  
unit) or replace the lamp early.  
44, 46  
1000 h  
Lamp replacement  
EXIT  
Displayed when the lamp use  
time exceeds 1000 hours.  
* The message does not appear if  
the lamp use time display is  
turned [OFF] with the OSD menu.  
Displayed when the lamp control  
setting is set to LIGHT OUTPUT  
CONTROL MODE (LOC) or LIGHT  
POWER CONTROL MODE (LPC)  
Arrange for a new lamp (lamp  
unit) or replace the lamp early.  
44, 46  
Appears every time the projector  
is turned on after the lamp use  
time has exceeded 1900 hours  
and until it reaches 2000 hours.  
Lamp replacement  
EXIT  
* The message is cleared by  
pressing any button.  
Displayed when the lamp control  
setting is set to LIGHT OUTPUT  
CONTROL MODE (LOC) or LIGHT  
POWER CONTROL MODE (LPC)  
Replace with a new lamp (lamp  
unit) and reset the lamp use time.  
44, 46  
When the lamp use time reaches  
2000 hours, the word “Warning”  
blinks on the screen.  
Warning  
Lamp replacement  
EXIT  
* To cancel this message, press  
the EXIT button.  
However, the same message will  
appear every hour.  
* If the power is turned off after the  
lamp use time has exceeded  
2000 hours, the power can not be  
turned on again.  
* When the lamp use time reaches  
2010 hours, the projector is  
forcibly turned off and can not be  
turned back on again.  
Memo  
The message display language corresponds to the menu display language setting. This is set to “English (English)” when the  
projector is bought. The display language can be selected from 6 languages. (Refer to page 46.) However, the input mode  
(PC1, PC2, DVI, Y/C, VIDEO, COMP) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English  
irrespective of the display language setting.  
The language settings in the section are explained in “English”.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Optical mechanism system  
Projection method  
D-ILA® (Direct Drive Image Light Amplifier) method  
(Reflective-type active-matrix method)  
D-ILA® device  
Projecting lens  
0.9" (2.3 cm) measured diagonally (1365 pixels × 1024 pixels) × 3  
(Total number of pixels : 4,193,280)  
GL-M2910G:  
1:1  
GL-M2915SG: 1.5:1 (with 2% zooming/shift function)  
GL-M2920ZG: × 1.5 zoom lens (2:1 to 3:1) (zooming function)  
GL-M2930SZG: × 1.9 zoom lens (2.9 to 5.5:1) (zooming/shift function)  
Screen size  
GL-M2910G:  
Refer to page 76.  
GL-M2915SG: Refer to page 76.  
GL-M2920ZG: Refer to page 77.  
GL-M2930SZG: Refer to page 77.  
Projection distance  
Light-source lamp  
GL-M2910G:  
Refer to page 76.  
GL-M2915SG: Refer to page 76.  
GL-M2920ZG: Refer to page 77.  
GL-M2930SZG: Refer to page 77.  
420 W xenon lamp  
Electrical system  
Color system  
Resolution  
NTSC, NTSC4.43, PAL (Automatic switching / manual switching)  
1365 dots × 1024 dots (S-XGA full resolution, during RGB input)  
1000 TV lines (Horizontal resolution, aspect ratio 4 : 3, during video input)  
Scanning frequency  
Audio power output  
Horizontal frequency : 15 kHz ~ 105 kHz  
Vertical frequency  
: 50 Hz ~ 100 Hz  
1 W (monaural), 1-5/8" (4 cm) round type micro-speaker × 1  
Input terminals  
[AV IN]  
Y/C  
1-line, mini-DIN 4 pin × 1 (for S-video)  
1-line, BNC × 1 (for composite video)  
1-line, BNC × 3 (for computer, DTV or video)  
Component (Y, B-Y, R-Y) signal  
VIDEO  
Y, B-Y, R-Y  
Y, PB, PR  
DTV-format (Y, PB, PR) signal  
[PC 1]  
R, G, B, H, V  
1-line, D-sub 3-row 15 pin × 1 (for computer)  
[PC 2]  
1-line, BNC × 5 (for computer, DTV or video)  
Analog RGB signal  
R, B, G  
H/Cs, V  
Horizontal (H) sync/composite (CS) sync, Vertical (V) sync signal  
[DVI]  
1-line, DVI-D 24-pin × 1  
[CONTROL]  
RS-232C  
1-line, D-sub 9-pin × 1  
* RS-232C-interface specified control terminal for controlling this projector with a personal  
computer.  
REMOTE  
1-line, stereo mini-jack × 1  
* Remote terminal for connecting with the remote control unit.  
Output terminal  
PC OUT  
1-line, D-sub 3-row 15-pin × 1 (output for display monitor)  
CONTROL OUT  
1-line, D-sub 9-pin × 1  
* RS-232C-interface specified control terminal for controlling this projector with a personal  
computer.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
General  
Power requirements  
Power consumption  
120 V AC, 50/60 Hz  
7 A  
Allowable operation  
temperature  
41°F to 95°F (+ 5°C to + 35°C)  
Allowable relative  
humidity  
20% to 80% (no condensation)  
14°F to 140°F (– 10°C to + 60°C)  
Allowable storage  
temperature  
Approx. 20" × 10-1/2" × 15-1/2" (Approx. 505 mm × 265 mm × 393 mm)  
[Carrying band, Excluding protrusions]  
Dimensions  
(Width × Height × Depth)  
Weight  
Approx. 32.12 lbs. (Approx. 14.6 kg)  
Accessories  
(Refer to page 5.)  
* Design and specifications are subject to change without notice.  
* D-ILA devices are manufactured with a very high-precision technology, allowing 99.99% of the pixels to be effective. Only  
0.01% or less of the pixels are missing or always on.  
* For easy understanding, pictures and illustrations maybe emphasized, composed or have omissions and may be more or  
less different from actual products.  
* TRADEMARKS  
D-ILA is a trademark of Victor Company of Japan, Limited.  
IBM and IBM PC are registered trademarks of International Business Machines Corporation. Macintosh is a registered  
trademarks of Apple Computer, Inc.  
VESA is a trademark of the non-profit organization Video Electronics Standards Association.  
All other product names mentioned herein are used for identification purposes only, and may be the trademarks or  
registered trademarks of their respective companies.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Outside dimensions  
Top  
Unit: inch  
22.430  
E N T E R  
E X I T  
M E N U  
V I D E O  
P R E S E T  
O
N
E
K
E
Y
S
T
P C  
H I D E  
T E  
O P E R A  
T B Y  
T E M P  
L A M P  
A N S D  
5-1/4 (133)  
Front  
Side  
19.300  
22.430  
2-7/8  
2-1/8  
15-1/2  
10-1/8  
(256)  
(
70)  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Pin assignment (Specifications for terminals)  
Y/C terminal  
Pin number  
Signal name  
1
2
3
4
GND (Y)  
4
2
3
1
GND (C)  
Y
C
RS-232C terminal  
Pin number  
Signal name  
Pin number  
Signal name  
9
8 7 6  
1
2
3
4
5
N/C  
RD  
6
7
8
9
N/C  
N/C  
N/C  
N/C  
TD  
N/C  
GND  
5 4 3 2 1  
PC1 terminal/PC OUT terminal  
Pin number  
Signal name  
Red  
Pin number  
Signal name  
N/C  
1
2
3
4
5
6
7
8
9
11 12 13 14 15  
Green  
10  
11  
12  
13  
14  
15  
GND (SYNC)  
GND  
Blue  
N/C  
N/C  
N/C  
H.SYNC  
V.SYNC  
N/C  
6
7
1 2 8 3 4  
5
9 10  
GND (Red)  
GND (Green)  
GND (Blue)  
DVI terminal  
Pin  
number  
Pin  
number  
Pin  
number  
Signal name  
Signal name  
T.M.D.S.Data1-  
Signal name  
1
2
3
T.M.D.S.Data2-  
9
17  
T.M.D.S.Data0-  
T.M.D.S.Data0+  
9
11 13 15  
10 12 14 16  
1 2 3 4 5 6 7 8  
T.M.D.S.Data2+ 10  
T.M.D.S.Data1+ 18  
T.M.D.S.Data2  
Shield  
11  
T.M.D.S.Data1  
Shield  
19  
T.M.D.S.Data0  
Shield  
4
5
6
No Connect  
No Connect  
DDC Clock  
12  
13  
14  
No Connect  
No Connect  
+5V Power  
20  
21  
22  
No Connect  
No Connect  
17 19 21 23  
18 20 22 24  
T.M.D.S. Clock  
Shield  
7
8
DDC Data  
15  
16  
Ground (for +5 V) 23  
Hot Plug Detect 24  
T.M.D.S. Clock +  
T.M.D.S. Clock -  
No Connect  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C external control  
By connecting a computer to the RS-232C terminal, you can control the projector. Use a reverse connection cable as the RS-  
232C connection cable.  
The commands to control the projector and the response data against the received commands are explained here.  
For further information, please consult the dealer where you purchased your projector or consult the Service Center.  
1. Communication Specifications  
The communication specifications are as follows:  
Baud rate  
Data length  
Parity  
9600bps / 19200bps*  
8 bits  
None  
1 bit  
Stop bit  
Flow control  
None  
* Factory set value. To change the value, refer to “Setting and Adjusting Other Functions (OPTIONS)” on page 54.  
2. Command Format  
2-1. Command data format (from the computer to the projector)  
When sending a control command, use the following data format.  
Header  
ID  
SP  
Command  
SP  
Parameter  
CR  
Header: Designates the head of data and the kind of data.  
“!” (21h): Control command to the projector  
“?” (3Fh): Query to the projector (Asking command)  
“1” (fixed)  
ID:  
SP:  
CR:  
Designates the delimiter for ID, Command, and Parameter. (20h)  
Designates the terminal of the data. (0Dh)  
* [ ] is not necessary when Asking command.  
2-2. Response data format (from the projector to the computer)  
Upon executing the received control command, the projector sends back the following response data to the computer.  
Header ID SP Normal Termination Status SP Parameter CR  
Header: Designates the head of data.  
“@” (40h): Fetches data from the projector.  
“1” (fixed)  
Designates the delimiter for ID, Command, and Parameter (20h)  
ID:  
SP:  
Normal Termination Status: “0” (30h)  
CR: Designates the terminal of the data (0Dh)  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C external control  
2-3 Parameters used for the data format  
The following three kinds of parameters are prepared for the control command and response data.  
(1) Numeric value  
Designates the 2-byte hexadecimal value with the sign as the 4-digit (byte) characters.  
Designation allowable range: “8000” to “7FFF”  
(2) ON/OFF  
Designates the status (ON/OFF) of the projector, such as POWER and HIDE.  
Character  
Hex.  
30  
Meaning  
OFF  
“0”  
“1”  
31  
ON  
(3) Special parameters  
Input switching parameters:  
Character  
Hex.  
30  
Meaning  
Y/C  
“0”  
“1”  
“2”  
“3”  
“4”  
“5”  
31  
VIDEO  
COMP  
PC1  
32  
33  
34  
PC2  
35  
DVI  
Operation mode parameters:  
Character  
“0000”  
Hex.  
Meaning  
30h, 30h, 30h, 30h  
30h, 30h, 30h, 31h  
30h, 30h, 30h, 32h  
30h, 30h, 30h, 34h  
Stand-by mode  
Power-on mode  
Cool-down mode  
Warning mode  
“0001”  
“0002”  
“0004”  
3. Control command table  
The control commands that can be sent from the computer are as follows:  
Asking  
Kind of data  
ON/OFF  
Function  
OPERATE  
Command  
Power ON  
ELSE  
Numeric Value  
Special Data  
U0F  
U00  
U17  
U18  
U40  
U1A  
HIDE  
Right Left rev.  
Top Bottom inv.  
Keystone  
Input  
Y/C, VIDEO, PC1, PC2,  
COMP, DVI  
Operation mode  
Z03  
Stand-by, Power-on,  
Cool-down, Warning  
* Keystone: Numeric value can range from “FF80” to “0080”  
* Operation mode: Only Asking command is possible  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Relationship between Projection Distances and Projection Screen Sizes  
Note: There is a 7% drop (for ceiling mount) using the anamorphic lens. Calculate 7% of the through distance.  
Notes  
• The relationship between the projection distances and projection screen sizes differs depending on the lens unit (optional)  
you are using.  
• The projection distance and projection screen sizes listed here are only for a guide. Use them as reference when setting the  
projector.  
For lens unit GL-M2910G (1:1):  
Approximate projection distance unit: ft (m)  
Projection screen size  
(Diagonal length)  
For 4:3 aspect-ratio screens  
For 16:9 aspect-ration screens  
36.7" (approx. 93.2 cm)  
40" (approx. 101.6 cm)  
50" (approx. 127.0 cm)  
60" (approx. 152.4 cm)  
70" (approx. 177.8 cm)  
80" (approx. 203.2 cm)  
90" (approx. 228.6 cm)  
100" (approx. 254.0 cm)  
110" (approx. 279.4 cm)  
120" (approx. 304.8 cm)  
130" (approx. 330.2 cm)  
140" (approx. 355.6 cm)  
150" (approx. 381.0 cm)  
160" (approx. 406.4 cm)  
170" (approx. 431.8 cm)  
180" (approx. 457.2 cm)  
190" (approx. 482.6 cm)  
200" (approx. 508.0 cm)  
---  
2.53 (0.77)  
2.76 (0.84)  
3.48 (1.06)  
4.20 (1.28)  
4.95 (1.51)  
5.68 (1.73)  
6.40 (1.95)  
7.12 (2.17)  
7.87 (2.40)  
8.60 (2.62)  
9.32 (2.84)  
10.04 (3.06)  
10.79 (3.29)  
11.52 (3.51)  
12.24 (3.73)  
12.96 (3.95)  
13.68 (4.17)  
---  
2.53 (0.77)  
3.18 (0.97)  
3.84 (1.17)  
4.53 (1.38)  
5.18 (1.58)  
5.87 (1.79)  
6.53 (1.99)  
7.22 (2.20)  
7.87 (2.40)  
8.53 (2.60)  
9.22 (2.81)  
9.88 (3.01)  
10.56 (3.22)  
11.22 (3.42)  
11.88 (3.62)  
12.57 (3.83)  
13.22 (4.03)  
For lens unit GL-M2915SG (1.5:1):  
Approximate projection distance unit: ft (m)  
Projection screen size  
(Diagonal length)  
For 4:3 aspect-ratio screens  
For 16:9 aspect-ration screens  
55" (approx. 139.7 cm)  
60" (approx. 152.4 cm)  
65" (approx. 165.1 cm)  
70" (approx. 177.8 cm)  
75" (approx. 190.5 cm)  
80" (approx. 203.2 cm)  
85" (approx. 215.9 cm)  
90" (approx. 228.6 cm)  
95" (approx. 241.3 cm)  
100" (approx. 254.0 cm)  
105" (approx. 266.7 cm)  
110" (approx. 279.4 cm)  
115" (approx. 292.1 cm)  
120" (approx. 304.8 cm)  
125" (approx. 317.5 cm)  
130" (approx. 330.2 cm)  
135" (approx. 342.9 cm)  
140" (approx. 355.6 cm)  
145" (approx. 368.3 cm)  
150" (approx. 381.0 cm)  
---  
6.00 (1.83)  
6.30 (1.92)  
6.82 (2.08)  
7.38 (2.25)  
7.91 (2.41)  
8.46 (2.58)  
9.02 (2.75)  
9.55 (2.91)  
10.10 (3.08)  
10.63 (3.24)  
11.19 (3.41)  
11.75 (3.58)  
12.27 (3.74)  
12.83 (3.91)  
13.35 (4.07)  
13.91 (4.24)  
14.44 (4.40)  
---  
5.77 (1.76)  
6.27 (1.91)  
6.76 (2.06)  
7.28 (2.22)  
7.78 (2.37)  
8.27 (2.52)  
8.76 (2.67)  
9.28 (2.83)  
9.78 (2.98)  
10.27 (3.13)  
10.76 (3.28)  
11.25 (3.43)  
11.78 (3.59)  
12.27 (3.74)  
12.76 (3.89)  
13.25 (4.04)  
13.75 (4.19)  
14.27 (4.35)  
14.76 (4.50)  
---  
---  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
For lens unit GL-M2920ZG (2 to 3:1):  
Approximate projection distance unit: ft (m)  
For 4:3 aspect-ratio screens For 16:9 aspect-ration screens  
Projection screen size  
(Diagonal length)  
Wide end  
Tele end  
Wide end  
Tele end  
40" (approx. 101.6 cm)  
42" (approx. 106.7 cm)  
50" (approx. 127.0 cm)  
60" (approx. 152.4 cm)  
70" (approx. 177.8 cm)  
80" (approx. 203.2 cm)  
100" (approx. 254.0 cm)  
150" (approx. 381.0 cm)  
200" (approx. 508.0 cm)  
240" (approx. 609.6 cm)  
250" (approx. 635.0 cm)  
300" (approx. 762.0 cm)  
310" (approx. 787.4 cm)  
320" (approx. 812.8 cm)  
330" (approx. 838.2 cm)  
340" (approx. 863.6 cm)  
350" (approx. 889.0 cm)  
400" (approx. 1016.0 cm)  
450" (approx. 1143.0 cm)  
470" (approx. 1193.8 cm)  
480" (approx. 1219.2 cm)  
500" (approx. 1270.0 cm)  
521" (approx. 1323.3 cm)  
---------  
---------  
---------  
---------  
---------  
8.23 (2.51)  
9.74 (2.97)  
11.65 (3.55)  
13.55 (4.13)  
15.42 (4.70)  
19.23 (5.86)  
28.71 (8.75)  
38.16 (11.63)  
45.73 (13.94)  
47.64 (14.52)  
57.09 (17.40)  
58.99 (17.98)  
60.89 (18.56)  
62.76 (19.13)  
64.67 (19.71)  
---------  
---------  
---------  
---------  
8.53 (2.60)  
9.96 (2.73)  
10.60 (3.23)  
12.66 (3.86)  
14.73 (4.49)  
16.80 (5.12)  
20.90 (6.37)  
31.23 (9.52)  
41.54 (12.66)  
49.80 (15.18)  
51.87 (15.81)  
62.17 (18.95)  
64.24 (19.58)  
---------  
8.50 (2.59)  
9.84 (3.00)  
11.22 (3.42)  
13.94 (4.25)  
20.77 (6.33)  
27.59 (8.41)  
33.04 (10.07)  
34.38 (10.48)  
41.21 (12.56)  
42.59 (12.98)  
43.93 (13.39)  
45.31 (13.81)  
46.65 (14.22)  
48.03 (14.64)  
54.86 (16.72)  
61.65 (18.79)  
64.37 (19.62)  
---------  
9.09 (2.77)  
10.33 (3.15)  
12.83 (3.91)  
19.09 (5.82)  
25.33 (7.72)  
30.35 (9.25)  
31.59 (9.63)  
37.86 (11.54)  
39.11 (11.92)  
40.35 (12.30)  
41.60 (12.68)  
42.85 (13.06)  
44.09 (13.44)  
50.36 (15.35)  
56.63 (17.26)  
59.12 (18.02)  
60.37 (18.40)  
62.89 (19.17)  
65.52 (19.97)  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
For lens unit GL-M2930SZG (2.9 to 5.5:1):  
Approximate projection distance unit: ft(m)  
For 4:3 aspect-ratio screens For 16:9 aspect-ration screens  
Projection screen size  
(Diagonal length)  
Wide end  
Tele end  
Wide end  
Tele end  
40" (approx. 101.6 cm)  
50" (approx. 127.0 cm)  
60" (approx. 152.4 cm)  
70" (approx. 177.8 cm)  
80" (approx. 203.2 cm)  
100" (approx. 254.0 cm)  
150" (approx. 381.0 cm)  
200" (approx. 508.0 cm)  
240" (approx. 609.6 cm)  
250" (approx. 635.0 cm)  
260" (approx. 660.4 cm)  
270" (approx. 685.8 cm)  
280" (approx. 711.2 cm)  
300" (approx. 762.0 cm)  
350" (approx. 889.0 cm)  
400" (approx. 1016.0 cm)  
470" (approx. 1193.8 cm)  
480" (approx. 1219.2 cm)  
500" (approx. 1270.0 cm)  
510" (approx. 1295.4 cm)  
---------  
---------  
---------  
---------  
14.83 (4.52)  
18.44 (5.62)  
22.05 (6.72)  
25.66 (7.82)  
29.30 (8.93)  
36.52 (11.13)  
54.59 (16.64)  
72.67 (22.15)  
87.14 (26.56)  
90.78 (27.67)  
94.39 (28.77)  
97.99 (29.87)  
---------  
---------  
---------  
---------  
16.11 (4.91)  
20.05 (6.11)  
23.98 (7.31)  
27.92 (8.51)  
31.86 (9.71)  
39.76 (12.12)  
59.45 (18.12)  
79.17 (24.13)  
94.91 (28.93)  
---------  
14.83 (4.52)  
16.93 (5.16)  
21.06 (6.42)  
31.43 (9.58)  
41.77 (12.73)  
50.07 (15.26)  
52.13 (15.89)  
54.20 (16.52)  
56.27 (17.15)  
58.33 (17.78)  
62.50 (19.05)  
72.83 (22.20)  
83.20 (25.36)  
97.70 (29.78)  
---------  
15.55 (4.74)  
19.36 (5.90)  
28.87 (8.80)  
38.39 (11.70)  
45.96 (14.01)  
47.86 (14.59)  
49.77 (15.17)  
51.67 (15.75)  
53.58 (16.33)  
57.38 (17.49)  
66.90 (20.39)  
76.41 (23.29)  
89.70 (27.34)  
91.60 (27.92)  
95.41 (29.08)  
97.31 (29.66)  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
---------  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kuppersbusch USA Microwave Oven EMWK10501E UL User Manual
La Crosse Technology Portable Radio WS 1515U IT User Manual
Lincoln Electric Welding System 200 M User Manual
Link electronic Portable Generator SPG 812 SA User Manual
Lochinvar Boiler PB PF 1500 User Manual
Loewe Projector Individual Sound Projector User Manual
LST Smoke Alarm ECO1005 User Manual
Makita Drill DA391D User Manual
Mamp;S Systems Garage Door Opener XDM46K User Manual
Mercedes Benz Automobile 2001 CLK 430 User Manual