OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
COMBINATION 13” COLOR TELEVISION
AND DVD/CD PLAYER
COMBINACION DE 13” TELEVISOR A COLOR
CON DVD/DISCOS COMPACTOS
MVD2113A
ATTENTION
ATENCION
If you purchase a universal remote control from your local retailer, please contact the
remote manufacturer for the required programming code.
Si usted a comprado un control remoto universal, por favor comunicace con el fabricante
para el codico de programaccion requerido.
TV/CABLE MODE SELECTION
SELECCION DE MODO DE TV/CABLE
When shipped from the factory, the TV/CABLE menu option is set to the "CABLE"
(Cable Television) mode.
If not using CABLE (Cable TV), set this menu option to the "TV" mode.
Al salir la unidad de fábrica, la opción de menú de TV/CABLE se ajusta al modo de
"CABLE" (Televisión por cable).
Si no utiliza CABLE, ajuste esta opción de menú al modo de "TV".
Before operating the unit, please read this manual thoroughly.
Antes de usar la unidad, lea detenidadmente este manual de instrucciones.
5P20521A [E] COV.
1
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
PORTABLE CART WARNING
(symbol provided by RETAC)
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
and to ensure reliable operation of the unit, and to protect it from overheating.
S3126A
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installations such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES
This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company. For
units intended to operate from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug, if your unit is equipped
with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a ground-
ing-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type plug.
3
5P20521A [E] P02-05
3
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
(Continued)
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c
. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
20. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
21. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
22. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
23. DISC TRAY
Keep your fingers clear of the disc tray as it is closing. It may cause serious personal injury.
24. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.
25. SOUND VOLUME
Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume
sound may cause hearing or speaker damage.
4
5P20521A [E] P02-05
4
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
26. SOUND DISTORTION
Do not allow the product to output distorted sound for an extended period of time. It may cause speaker
overheating and fire.
27. HEADPHONES
When you use the headphones, keep the volume at a moderate level. If you use the headphones continu-
ously with high volume sound, it may cause hearing damage.
28. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause eye damage.
29. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
30. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the CABLE TV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD
IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
ELECTRIC SERVICE
(NEC SECTION 810-21)
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC-NATIONAL ELECTRICAL CODE
S2898A
CONDENSATION
Moisture will form in the operating section of the player if the player is brought from cool surroundings
into a warm room or if the temperature of the room rises suddenly. When this happens, player's
performance will be impaired.
To prevent this, let the player stand in its new surroundings for about an hour before switching it on, or
make sure that the room temperature rises gradually.
Condensation may also form during the summer if the player is exposed to the breeze from an air
conditioner. In such cases, change the location of the player.
5
5P20521A [E] P02-05
5
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Color TV With DVD/CD player
Unique space saving design combines a 13" color TV and a DVD/CD player.
The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture/Audio quality of the
DVD exceeds other software. Picture quality is higher than Super VHS. Audio quality is higher than audio CD. The
DVD also has special options; audio language selection, subtitle language selection or multi-angle, etc.
The DVD PLAYER can play back audio CDs.
High Quality Picture
Horizontal Resolution
More than 500 lines. It exceeds Super VHS (400 lines) or Laser Disc (430 lines) in resolution.
Compatible with a wide range of DVD audio outputs
Digital Audio Jack (Coaxial)
• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect
of being in a movie theatre or a concert hall.
• Surround standard different from Dolby Digital. This format is already in use in many theatres. By connecting this
unit to a DTS decoder or anAV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this
format can be enjoyed. However, audio will not be output from the analog audio output jacks.
• By connecting this unit to an AV amplifier with a built-in MPEG decoder, the MPEG audio of DVD discs recorded
in this format can be enjoyed.
• The Linear PCM sound of a 48 kHz/24 bit through 96 kHz/24 bit exceeds audio CD sound.
Convenience Features
Direct selection of your desired scenes using Title/Chapter/Time/Track - You can play back from the desired
scene.
Recalling Up to 3 Scenes (DVD only) - You can program up to 3 scenes in memory and recall the marked scenes.
Frame Advance - The PAUSE/STILL moves one frame at a time.
Slow Motion - The SLOW moves you back and forth through the program by 4 steps of 1/7-1/2 times.
Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.
Program Playback (Audio CD) - You can play back tracks in programmed sequences.
Zoom (DVD only) - You can zoom in the selected subject on the screen during playback.
Note: Make sure that discs are suitable for the following functions.
Multi-Language - Maximum 32 language subtitles and maximum 8 language soundtracks can be played back for
movies or programes.
Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc,
you can change the angles during playback.
Parental Control - You can limit the play back of scenes or sounds of adult DVD discs which have parental level.
Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor.
TV Features
181 Channel Tuner - Receives standard VHF and UHF broadcast channels and up to 113 cable channels. The
actual number of channels received depends upon channel reception in your area or your cable system.
Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for
hearing impaired viewers.
Picture Adjustments Using The Remote Control - The On-Screen display allows precise remote control adjust-
ment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.
Programmable TV Sleep Timer - Operable from the remote control, the TV can be programmed up to 120
minutes to turn off automatically.
On-Screen 3 Language Display - You can select one of 3 languages, English, Spanish or French for on-
screen programming.
V-Chip - The V-Chip function can read the rating of a TV program or movie content if the program is encoded
with this information. V-chip will allow you to set a restriction level.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be authorized by Macrovision Corporation and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
6
5P20521A [E] P06-11
6
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before using your unit
IMPORTANT SAFEGUARDS .............................................. 3
Features ............................................................................... 6
Contents............................................................................... 7
Parts and functions .............................................................. 8
Remote control..................................................................... 9
Power source ..................................................................... 10
Antenna connections.......................................................... 11
Cable TV connections ........................................................ 12
TV operation
Setting the language .......................................................... 13
TV operation....................................................................... 14
Closed caption ................................................................... 16
Memorizing channels ......................................................... 17
Setting the V-Chip .............................................................. 19
Picture control adjustment.................................................. 22
Adjusting the picture preference ........................................ 23
Stereo and second audio program (SAP) .......................... 24
Playback operation
Disc .................................................................................... 25
Preparation/Status display of disc...................................... 26
Setting setup language ...................................................... 27
Playback procedure ........................................................... 28
Special playback ................................................................ 29
Advanced Function
Zooming/Locating desired scene ....................................... 30
Repeat playback ................................................................ 31
Program playback/Random playback (CD) ........................ 32
Marking desired scenes ......................... ........................... 33
Changing soundtrack language/Subtitles .......................... 34
Changing angles/Title selection/DVD menu....................... 35
Additional Information
Setting the aspect ratio of TV screen/
Setting on screen display ................................................... 36
Dynamic Range Control ..................................................... 37
Parental control setting ..................................................... 38
Changing the parental level .............................................. 39
Temporary disabling of rating level by DVD disc................ 40
Setting menu language ...................................................... 41
Setting subtitle language.................................................... 42
Setting audio soundtrack language.................................... 43
Language code list ............................................................. 44
Connections to other equipment ........................................ 45
Reception disturbances...................................................... 47
Problems and troubleshooting ........................................... 48
Specifications ..................................................................... 50
7
5P20521A [E] P06-11
7
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and functions
Front
Disc tray
SKIP buttons
Headphones jack
Power indicator
POWER button
AUDIO IN (L/R) jacks
VIDEO IN jack
STOP button
PLAY button
Remote sensor
OPEN/CLOSE button
VOLUME UP/DOWN buttons
CHANNEL UP/DOWN buttons
Rear
RF IN jack
UHF/
VHF
UHF/
VHF
COAXIAL DIGITAL AUDIO OUT jack
AC power cord
8
5P20521A [E] P06-11
8
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Page
POWER
Power On/Off
13,14,26,28
DISPLAY/CALL
Call TV information
Call DVD information
15
26
TV/DVD
OPEN/CLOSE
0-9
Switch between TV/AV and DVD
Open or Close the tray
26,27,37
28,40
Direct channel selection of TV
Input setting
Enter a password
14,18
30,32
19,21,38~40
VOL +/–
MUTE
Adjust volume of TV
Switch off the sound
Sleep timer
14
15
15
15
SLEEP
CH
/
Select channel of TV
Cursor buttons
13,17~23,27,28,30~33,
36~43
SELECT/ENTER
SETUP/TV MENU
Enter information in the menu 13,19,20~23,27,
28,30~33,35~43
TV mode - Display menu of TV
13,17~23
DVD mode - Call up initial setup mode 27,36~39,41~43
DVD MENU
CANCEL
Display DVD menu
35
Reset information in the menu 19,21,22,30,32,33,38,39
TOP MENU
SEARCH8/9
PLAY A
Select title
35
29
Fast Forward/Review playback
Playback
28,29,31,32,35,40
SKIP
/
Skip chapter to forward or reverse
direction
29
SUBTITLE
STOP
Set subtitle
34
28
Stop
SLOW
/
Forward/Reverse- slow motion
29
29
PAUSE/STILL
Pause CD sound
Still picture of DVD
PLAY MODE
Select playback mode
31,32
RETURN
Remove DVD set up menu
27,36~43
31
REPEAT A-B
Repeat playback between A and B
ANGLE
AUDIO
Change playback angle
35
Switch the sound of TV
Change sound track language
24
34
MARKER
Index
33
JUMP
Locating desired scene
30
16
TV/CAP/TEXT
Switch between TV/Caption/Text in
Closed Caption mode
ATTENTION
QUICK VIEW/ZOOM Switch between present/last channel
Zoom
15
30
If you purchase a universal remote control
from your local retailer, please contact the
remote manufacturer for the required
programming code.
INPUT SELECT
Switch between TV/AV
46
9
5P20521A [E] P06-11
9
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
(Continued)
Inserting Batteries
Open the battery compartment
cover in the direction of the
arrow.
Install two "AAA" batteries
(not supplied), paying attention
to the polarity diagram in the
battery compartment.
Replace the compartment
cover.
1
2
3
Operation
• Aim the remote control at the remote sensor and
press control buttons to operate.
• Operate the remote control within 30° angle on
either side of the remote sensor, up to a dis-
tance of Approx. 5 meters.
Approx. 5 meters
NOTES:
•
•
Do not leave the remote control unit exposed to direct sunlight or in hot or humid places.
The remote control unit uses infrared beams to transmit signals, so sunlight or fluorescent light on the remote
sensor may shorten operating distance.
•
Incorrect use of batteries may cause them to leak or burst. Read the battery warnings and use the batteries
properly.
•
•
Do not mix old and new batteries.
Remove batteries if the remote control will not be operated for an extended period of time.
Power source
TO USE AC POWER
Use the AC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.
AC Outlet
Wider Hole
and Blade
NOTES:
Never connect the AC line cord plug to anything other than the
specified voltage (120V 60Hz). Use the attached power cord only.
If the polarized AC cord does not fit into a non polarized AC
outlet, do not attempt to file or cut the blade. It is the user’s
responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit, and the
unit fails to function, simply unplug the unit from the AC outlet,
wait a few minutes, and plug it back in. The unit should return to
normal operation.
•
•
•
Polarized AC Cord Plug
(One blade is wider than the other)
10
5P20521A [E] P06-11
10
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Antenna connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your
antenna system. If you are using a cable TV service (CABLE), see page 12 for Cable TV connections.
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from the combination
VHF/UHF antenna to the antenna jack.
If your combination VHF/UHF antenna has a 300
ohm twin-lead wire, the use of the 300-75 ohm
matching transformer may be necessary.
Antenna
jack
Antenna
jack
75 ohm
coaxial
cable
300-75 ohm
matching
transformer
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Connect the UHF 300 ohm twin-lead wire to the
combiner (not supplied). Connect the VHF 300 ohm
twin-lead wire to the 300-75 ohm matching trans-
300-75 ohm
former. Attach the transformer to the combiner, then
matching
attach the combiner to the antenna jack.
transformer
Antenna
jack
Combiner
UHF 300 ohm
VHF 300 ohm
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Connect the VHF 75 ohm cable and UHF 300
ohm twin-lead wire to the combiner (not supplied).
Attach the combiner to the antenna jack.
VHF 75 ohm
Antenna
jack
Combiner
UHF 300 ohm
11
5P20521A [E] P06-11
11
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable TV connections
This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable
TV converter box. Some cable companies offer “premium pay channels” in which the signal is
scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device
which is generally provided by the cable company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a converter/descrambler
box, connect the 75 ohm coaxial cable directly to the antenna
jack on the back of the TV/DVD.
75 ohm
coaxial cable
Antenna
jack
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the
incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect
the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections
shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel 3 or 4)
and use the converter/descrambler box to select channels.
Incoming
75 ohm
Cable TV cable
75 ohm cable to
TV/DVD
Converter/
descrambler
Antenna
jack
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH
SCRAMBLED PREMIUM CHANNELS
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require
the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B switch box (available
from the cable company or an electronics supply store). Follow the connections shown below. With the switch in
the “B” position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the “A”
position, tune your TV/DVD to the output of the converter/descrambler box (usually channel 3 or 4) and use the
converter/descrambler box to tune scrambled channels.
Inc
75
Ca
Antenna
jack
12
5P20521A [E] P12-17
12
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the language
You can choose from three different languages (English, French and Spanish) for the on-screen displays.
To turn on the TV/DVD, press POWER. The Power indicator
1 will light.
Press TV MENU in the TV mode.
2
The TV menu screen will appear.
Press
option.
or
to select
3
4
A
B C
CH
LANGUAGE/IDIOMA/LANGUE
/MENU
Press
or
to select the
A
B C
CH
desired language: English
(ENGLISH), Spanish
(ESPAÑOL) or French
(FRANCAIS), then press
ENTER.
LANGUAGE/IDIOMA/LANGUE
/
/ ENTER/MENU
Press TV MENU until the menu
screen is cleared.
5
NOTES:
If the unit does not operate properly
(by the buttons on the unit and/or the
remote control) disconnect the AC
cord, wait a few minutes and plug it
back in. Static electricity, etc., may have
affected the player's operation.
•
The TV section has its own menu and
also DVD section has its own menu
(see page 27).
•
13
5P20521A [E] P12-17
13
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TV operation
To turn on the TV/DVD, press
1 POWER.
Adjust the volume level by
2 pressing VOL + or – . The
volume level will be indicated on
the screen by green bars. As the
volume level increases, so do
the number of bars. If the volume
decreases, the number of green
bars also decreases.
VOLUME
32
Set the TV/CABLE menu
3 option to the appropriate
TV
- VHF/UHF channels
CABLE - CABLE channels
position. (See page 17.)
Press the Direct Channel selection
4 buttons to select the channel.
CH 02
TV Mode Direct Channel Selection
When the TV/CABLE menu option
is in the TV position, all channels
can be instantly selected by using
two buttons. (for example, to select
channel 2, press “0”, then “2”. If
you press only “2”, channel
selection will be delayed for a few
seconds.) For channels 10 and
above, press the 2 digits in order.
CABLE Mode Direct Channel Selection
When the TV/CABLE menu option is in the CABLE position, channels
can be selected as follows:
TO SELECT Cable TV CHANNELS:
1-9:
Press “0” twice, then 1-9 as needed. Example, to select
channel 2, press “002”.
10-12:
13-99:
Press “0”, then the remaining 2 digits. Example, to
select channel 12, press “012”.
Press the 2 digits in order. Example, to select channel
36, press “36”.
100-125: Press the 3 digits in order. Example, to select channel
120, press “120”.
NOTE FOR CHANNELS 1-12:
If only 1 or 2 buttons are pressed, the corresponding channel
will be selected in 2 seconds.
CABLE
TV
VHF
2-13
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
NOTES:
• If a channel with no broadcast is
selected, the sound will automati-
cally be muted.
• If a station being viewed stops
broadcasting, the TV will automati-
cally shut itself off after 15 minutes.
(5A)
14
5P20521A [E] P12-17
14
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANNEL UP/DOWN
Press and release CH
or . The
channel automatically stops at the
next channel set into memory.
For proper operation, before select-
ing channels, they should be set into
the memory. See pages 17 and 18
“To memorize channels”
CALL
Press DISPLAY/CALL to display the
current information on the screen.
Press DISPLAY/CALL again to clear
the call display.
STEREO SAP
SEL. STEREO
CH 012
• Channel number or VIDEO mode
• Stereo or SAP (second audio
program) audio status
• Audio output status
QUICK VIEW
This button allows you to go back to
the last channel selected by press-
ing QUICK VIEW. Press QUICK
VIEW again to return to the last
channel you were watching.
MUTE
Press MUTE to switch off the sound.
The TV/DVD’s sound will be silenced
and “MUTE” will briefly appear on the
screen. The sound can be switched
back on by pressing this button
again or one of the VOL + or –
buttons.
MUTE
SLEEP
SLEEP
120
To set the TV/DVD to turn off after a
preset amount of time, press SLEEP
on the remote control. The clock will
count down 10 minutes for each press
of SLEEP (120, 110, ...10, 0). After the
sleep time is programmed, the display
will appear briefly every ten minutes
to remind you that the sleep timer is
operating. To confirm the sleep timer
setting, press SLEEP and the remain-
ing time will be displayed for a few
seconds. To cancel the sleep timer,
press SLEEP repeatedly until the dis-
play turns to 0.
15
5P20521A [E] P12-17
15
5/12/04, 2:41 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed caption
WHAT IS CLOSED CAPTIONING?
This television has the capability to decode and display closed captioned television programs. closed captioning
will display text on the screen for hearing impaired viewers or it will translate and display text in another language.
Captions: This closed caption mode will display text on the
screen in English or another language (depending on the set-
ting of the closed captions CH 1/2).
Generally, closed captions in English are transmitted on captions
channel 1 and closed captions in other languages are transmitted
on captions channel 2.
The captions will appear in places on the screen where they will
least interfere with the picture, usually on the bottom of the screen.
News programs will usually show three-line closed captions which
scroll onto the screen.
Most other shows provide two or three lined captions placed
near the character who is speaking so the viewer can follow the
dialogue. Words in italics or underlined describe titles, words in
foreign languages or words requiring emphasis. Words that are
sung usually appear enclosed by musical notes.
Text: The text closed caption mode will usually fill the screen
with a programming schedule or other information.
After selecting a closed caption mode, it will stay in effect until it
is changed, even if the channel is changed.
If the captions signal is lost due to a commercial or a break in
the signal, the captions will reappear when the signal is received
again. If the channels are changed, the captions will be delayed
approximately 10 seconds.
For television programs broadcasting with closed captions, look
in your TV guide for the closed captions symbol (CC).
TO VIEW CLOSED CAPTIONS
Press TV/CAP/TEXT to switch
between normal TV and the two
closed caption modes (captions
and full screen text). Closed
captioning will display text on the
screen for hearing impaired
viewers.
NOTES:
• When selecting closed captions, the captioning will be delayed approximately 10 seconds.
• If no caption signal is received, no captions will appear, but the television will remain in the caption mode.
• Misspellings or unusual characters may occasionally appear during closed captioning. This is normal with
closed captioning, especially with live programs. This is because during live programs, captions are also
entered live. These transmissions do not allow time for editing.
• When captions are being displayed, on-screen displays, such as volume and mute may not be seen or may
interfere with closed captions.
• Some cable systems and copy protection systems may interfere with the closed captioned signal.
• If using an indoor antenna or if TV reception is very poor, the closed caption decoder may not appear or
may appear with strange characters or misspelled words. In this case, adjust the antenna for better reception
or use an outdoor antenna.
16
5P20521A [E] P12-17
16
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorizing channels
This TV/DVD is equipped with a channel memory feature which allows channels to skip up or down to the next
channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed
into the TV/DVD’s memory. In addition to normal VHF and UHF channels, this TV/DVD can receive up to 113
Cable TV channels. To use this TV/DVD with an antenna, set the TV/CABLE menu option to the TV mode. When
shipped from the factory, this menu option is in the CABLE mode.
TV/CABLE SELECTION
Press TV MENU in the TV mode.
1 The TV menu screen will appear.
CH
Press
option.
or
to select
2
A
B C
CH
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Press
“TV/CABLE” option.
or
to select the
3
4
A
B C
CH
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Press
or CABLE mode.
or
to select the TV
A
B C
CH
TV
- VHF/UHF channels
TV/CABLE
TV
AUTO CH MEMORY
ADD/ DELETE
CABLE - CABLE channels
/
/
/
/ MENU
Press TV MENU until the menu
5 screen is cleared.
Cable TV CHART
The chart below is typical of many cable system channel allocations.
17
5P20521A [E] P12-17
17
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorizing channels
(Continued)
AUTOMATIC MEMORY TUNING
Press TV MENU in the TV mode.
1 The TV menu screen will appear.
2
A
B C
CH
CH
Press
or
select
option.
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Press
or
to select the “AUTO
3
A
B C
CH
CH MEMORY”, then press
The TV will begin memorizing all the
channels available in your area.
.
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
Press TV MENU until the menu
4 screen is cleared.
/
/
/ MENU
TO ADD/DELETE CHANNELS
Press TV MENU. The TV
1 menu screen will appear.
A
B C
CH
CH
Press
or
select
option.
2
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Press
or
to select the
A
B C
CH
3 “ADD/DELETE”, then press
.
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/ MENU
Select the desired channel to be
ADD
CH 001
4 memorized or deleted using Direct
Channel Selection (0-9), or CH
or
.
Press
or
to select ADD or
0-9 /
/
/
/
/ MENU
DELETE, whichever function you
want to perform.
Press TV MENU until the menu
5 screen is cleared.
Repeat steps 1~5 for other channels you want to add or delete.
6
18
5P20521A [E] P18-26
18
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the V-Chip
An age limitation can be set to forbid children to see and hear violent scenes or pictures for adults, etc.
The unit corresponds to "TV RATING" and "MOVIE RATING". To use the V-Chip function, you must
register a password.
TO REGISTER PASSWORD
Press TV MENU in the TV mode.
The TV menu screen will appear.
1
2
Press
then press
“PASSWORD”.
or
to select
or to select
option,
A
B C
CH
/
/
/
/ MENU
Enter the password (4 digits)
3
A
B C
CH
using Direct Channel Selection
(0-9), then press ENTER.
If you put a wrong number, press
CANCEL.
0-9/ENTER/CANCEL/MENU
"
" appears instead of the number.
Enter the same password again
for the safety, then press ENTER.
Now the password was registered
and V-Chip setting menu will
appear on the display.
4
A
B C
CH
V-CHIP SET
NEW
PASSWORD
:
0-9/ENTER/CANCEL/MENU
NOTES:
If you forget the password, you
cannot set the V-chip.
•
To avoid forgetting the password,
write it down and keep in the safe
place.
•
19
5P20521A [E] P18-26
19
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the V-Chip
(continued)
TO SET THE V-CHIP
In the V-CHIP SET menu, press
A
1
B C
CH
or
to select “ V-CHIP SET”,
then press
.
V-CHIP
V-CHIP SET
OFF
CHANGE PASSWORD
/
/
/ MENU
A
Press
or
RATING”, then press
display the desired setting.
to select “TV
B C
CH
2
or
to
V-CHIP SET
TV RATING
TV-Y7
OFF
MOVIE RATING
OFF
TV-Y
:
:
TV RATING is not set
All children
TV-Y7 :
TV-G :
TV-PG:
TV-14 :
TV-MA:
7 years old and above
General audience
Parental guidance
14 years old and above
17 years old and above
/
/
/
/ ENTER/MENU
When you select TV- Y7, TV-PG, TV-14 or TV-MA, press
DISPLAY/CALL to show the contained rating. Press or
to select the desired item you want. Press
the setting “ON” or “OFF”.
or
to select
A
Press
or
to select “MOVIE
B C
CH
3
4
RATING”.
V-CHIP SET
TV RATING
MOVIE RATING
TV-Y7
OFF
/
/
/
/ ENTER/MENU
A
Press
or
to select desired
B C
CH
rating, then press ENTER.
V - CHIP SET
TV RATING
MOVIE RATING
TV
PG
-
-
Y7
13
OFF
G
PG
:
:
:
MOVIE RATING is not set
All ages
Parental guidance
To use the TV after the TV is protected.
When the program applied to the V-Chip
setting is received, enter the password,
then press ENTER. When the password is
entered correctly the protection will be
temporarily overridden.
PG-13 : Parental guidance
/
/
/
/ ENTER/MENU
less than 13 years old
Under 17 years old
R
:
Parental guidance suggested
NC-17 : 17 years old and above
X
:
Adult only
NOTES:
Press
“V-CHIP”.
or
to select
A
• The V-Chip function is activated only on
programs and tapes that have the rating
signal.
5
B C
CH
V-CHIP
V-CHIP SET
CHANGE PASSWORD
OFF
• If you are changing channels using
a VCR or a cable box, while the TV
remains on channel 3 or 4, the V-Chip
operates differently. When you enter
your password to temporarily release
the block on any channel, you have
completely disabled the V-Chip function
for all stations. To reset the V-Chip turn
your TV off and back on.
• Some cable boxes are built with a delay
feature, in some cases it can take up to
10 seconds for a program to appear
after the password has been input.
/
/
/
/ MENU
Press
or
to display “ON”.
A
6
7
B C
CH
Now your settings were set into
the memory.
V-CHIP
V-CHIP SET
ON
CHANGE PASSWORD
Press TV MENU until the menu
screen is cleared.
/
/
/
/ MENU
20
5P20521A [E] P18-26
20
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
TO CHANGE PASSWORD
Press TV MENU in the TV mode.
The TV menu screen will appear.
1
Press
or
to select
option.
2
A
B C
CH
/
/
/
/ MENU
Press
“PASSWORD”.
or
to select the
A
3
B C
CH
0-9/ENTER/CANCEL/MENU
Enter the Password using Direct
Channel Selection (0-9), then
press ENTER.
If you put a wrong number, press
CANCEL.
A
B C
4
5
6
CH
V-CHIP SET
PASSWORD
:
0-9/ENTER/CANCEL/MENU
Press
“CHANGE PASSWORD”, then
press
or
to select
A
B C
CH
.
V-CHIP
V-CHIP SET
ON
CHANGE PASSWORD
/
/
/MENU
Enter the new password using
Direct Channel Selection (0-9),
then press ENTER.
A
B C
CH
0-9/ENTER/CANCEL/MENU
A
Enter the same password again
to confirm, then press ENTER.
B C
7
8
CH
Press TV MENU repeatedly to
return to normal screen.
21
5P20521A [E] P18-26
21
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture control adjustment
Picture controls are factory preset but you can adjust them individually as follows:
Press TV MENU in the TV mode.
The TV menu screen will appear.
1
Press
option.
or
to select
2
A
B C
CH
PICTURE
PICTURE PREFERENCE
/
/
/
/ MENU
Press
or
to select
3
A
B C
CH
“PICTURE”, then press
.
PICTURE
PICTURE PREFERENCE
/
/
/ MENU
Press
you want to adjust.
or
to select the item
A
4
5
B C
CH
BRIGHTNESS
CONTRAST
COLOR
0
+32
0
0
0
TINT
SHARPNESS
/
/
/
/ CANCEL / MENU
Press
or
to adjust the setting.
increase brightness
increase contrast
brilliant color
decrease brightness
decrease contrast
pale color
BRIGHTNESS
CONTRAST
COLOR
greenish color
reddish color
TINT
makes picture softer
makes picture clearer
SHARPNESS
After your desired setting changes press TV MENU until the
6 menu screen is cleared.
CANCEL
Pressing CANCEL while making picture adjustments will return all
adjustments to the factory preset levels.
NOTE:
The CONTRAST default setting is set
to maximum at the factory.
22
5P20521A [E] P18-26
22
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture preference
You can select four picture modes–STANDARD, SPORTS, MOVIE, and MEMORY–as described in the
following table:
Press TV MENU in the TV mode.
The TV menu screen will appear.
1
Press
option.
or
to select
2
A
B C
CH
PICTURE
PICTURE PREFERENCE
/
/
/
/ MENU
Press
or
to select
3
A
B C
CH
“PICTURE PREFERENCE”,
then press
.
PICTURE
PICTURE PREFERENCE
/
/
/ MENU
Press
or
to select the
4 desired picture mode, then
A
B C
CH
PICTURE PREFERENCE
STANDARD
SPORTS
press ENTER.
MOVIE
MEMORY
/
/ ENTER / MENU
Mode
Picture quality
STANDARD Standard picture quality (factory-set)
SPORTS
MOVIE
Bright and dynamic picture (factory-set)
Movie-like picture setting (factory-set)
MEMORY
Your personal preferences (set by you; see
“Picture control adjustment” on the page 22)
After your desired setting changes press TV MENU until the
5 menu screen is cleared.
23
5P20521A [E] P18-26
23
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Stereo and second audio program (SAP)
The TV/DVD is equipped with a feature known as Multi-channel TV Sound or MTS. MTS broadcasts greatly
enhance TV viewing by bringing you programs with high fidelity stereo sound.
MTS also provides an extra channel called the Second Audio Program or SAP which broadcasters can use to
transmit a second language for bilingual transmission or for other purposes.
LISTENING TO STEREO SOUND
When the TV is turned on or a
channel selection is made, make
STEREO
CH 013
certain the STEREO appears on
the screen. This means that
“Stereo” broadcasting is avail-
able. You can enjoy stereo
sound from the left and right
speakers.
• When “Mono” broadcasting is
received, no indication is
displayed.
• If the broadcast signal is not
strong enough or clear stereo
sound is not available, press
AUDIO to change to mono
sound. The noise should be
eliminated. Press it again to
return to the stereo sound.
LISTENING TO SAP (SECOND AUDIO PROGRAM)
When the TV is turned on or a
channel selection is made, make
certain the SAP appears on the
screen. This means that the
“Second Audio Program”
STEREO SAP
CH 013
broadcasting is available.
TO SELECT DESIRED SOUND
Press AUDIO to select the
desired sound.
SEL. STEREO
STEREO+SAP BROADCASTING
STEREO SOUND
(MAIN)
SAP SOUND
MONO SOUND
(MAIN)
24
5P20521A [E] P18-26
24
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc
This unit applies to DVD discs from Region 1 or Region ALL.
The loaded Disc (DVD and Audio-CD) will be recognized automatically.
The suitable disc formats are: DVD-Video, CD, CD-R/RW and DVD-R/RW (Video format only).
Some CD-R/RW discs may be incompatible.
Do not play DVD-ROM, DVD-Audio, CDV, CD-G, Video CD or Photo CD to prevent accidental erasure of prerecorded
material.
This unit does not play MP3/WMA/JPEG files.
Title
When two or more movies are recorded on a disc,
the disc is divided into two or more sections. Each
section is called a “TITLE”.
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Audio-CD
TRACK
1
TRACK
2
TRACK
3
TRACK
4
TRACK
5
Track
An Audio CD can contain several items.
These are assigned to tracks.
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe in circular direction.
• Do not use liquid or aerosol cleaners.
25
5P20521A [E] P18-26
25
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation/Status display of disc
The following pages describe the
setup/operation in DVD mode.
Preparation
Before DVD/CD operation, please make preparations as follows.
Insert the AC cord plug into a standard 120V 60Hz polarized
AC outlet.
• If the AC cord plug is plugged in for the first time, wait for
about 5 seconds before pressing POWER.
1
NOTE: When connecting to other equipment, unplug the unit
from the AC outlet.
Press POWER on the unit or on the remote control to turn on
2
the unit. The POWER indicator will light.
• Every time you press POWER, the TV/DVD starts from TV
mode.
• When using an amplifier, switch on the amplifier.
Press TV/DVD to select DVD
mode.
The DVD startup screen will ap-
pear on the screen.
3
No Disc
Status display of disc
Press DISPLAY/CALL twice. The status display of the disc will
appear on the screen.
DVD
Chapter number
Title number
Title elapsed playing time
Disc operation
Title total time
Camera angle
Type of audio
00:34:56 01:12:33
1/99 Chapter 1/999
1/9
1/8 Eng Dolby Digital
1/32 Eng
Title
Audio language
Subtitle language
To make status display disappear, press DISPLAY/CALL again.
Audio CD
Track elapsed playing time
NOTE:
Disc operation
Track number
Track total time
34:56
71:33
If the unit does not operate properly:
Static electricity, etc., may affect the
player's operation. Disconnect the AC
power cord once, then connect it again.
Track 11/99
• When you play a CD disc, the status display will appear
and remain on the screen.
26
5P20521A [E] P18-26
26
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting setup language
You can change the default settings
to customize performance to your
preference.
Press TV/DVD to select
the DVD mode.
1
2
3
No Disc
“No Disc” will appear on
the screen. (If a DVD disc
has already loaded, the
playback will start
automatically.)
Press SETUP in the stop
mode. The SETUP MENU
of DVD will appear on the
screen.
Language Picture Sound Parental Other
Then press
“Other”.
to select
/Enter/Setup/Return
Press
or ENTER to
select “OSD Language”.
Language Picture Sound Parental Other
OSD Language English
/Enter/Setup/Return
Press
then press or to
select desired language
(e.g. English), then press
ENTER.
or ENTER and
Language Picture Sound Parental Other
4
5
OSD Language English
English
Francais
Espanol
/Enter/Setup/Return
Press SETUP or RETURN to remove the Menu screen.
NOTES:
• If the selected soundtrack language is
not recorded on the disc, the original
language will be heard.
• If the selected subtitle language is not
recorded on the disc, the first-priority
language is selected.
27
5P20521A [E] P27-32
27
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback procedure
Press TV/DVD to select
the DVD mode.
Press OPEN/CLOSE on
the unit or the remote
control.
1
The disc tray will open.
Place a disc onto the
tray. Position it with the
printed label side up,
align it with the guides,
and place it in its proper
position.
2
3
Press PLAY or OPEN/
CLOSE.
The disc tray closes
automatically.
On the screen,
changes
to “Reading” and then
playback will commence.
• A menu screen may
appear on the TV screen,
if the disc has a menu
feature. In this case,
Reading
press
ENTER to operate a
menu feature.
,
,
,
or
NOTES:
• If a non-compatible disc is loaded,
“Incorrect Disc”, “Region Code Error” or
“Parental Error” will appear on the TV
screen according to the type of loaded
disc. If these appear, check your disc
again (see pages 25 and 38).
• Some discs may take a minute or so to
start playback.
• A “Prohibition” symbol may appear at
the upper left of the screen.
This symbol means either the feature you
tried is not available on the disc, or the
unit can not access the feature at this
time. This does not indicate a problem
with the unit.
Press STOP to end playback.
4
5
• The unit memorizes the stopped point, depending on
the disc. “ ” appears on the screen for approx. 4 seconds.
Press PLAY to resume playback (from the scene point).
• If you press STOP again (“ ” appears on the screen)
or unload the disc, the unit will clear the stopped point.
Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and unit turns off.
• When you set a single-faced disc label
downwards (ie. the wrong way up) and
press PLAY or OPEN/CLOSE on the
unit, “Reading” will appear on the display
and then “Incorrect Disc” will be dis played.
• Some playback operations of DVDs may
be intentionally fixed by software
producers. Since this unit plays DVDs
according to the disc contents the
software producers designed, some
playback features may not be
available. Also refer to the instructions
supplied with the DVDs.
28
5P20521A [E] P27-32
28
5/12/04, 2:42 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Special playback
NOTE: There may be a slight delay be-
tween when you press the button and
the function activating.
Fast Forward Playback
Press SEARCH during normal playback.
Each press of the SEARCH button will increase the speed
of the search (x 2), (x 4), (x 8), (x 15).
(CD: (x 2), (x 4), (x 8),
(x 20))
• To resume normal playback, press PLAY.
Review Playback
Press SEARCH
during normal playback.
Each press of the SEARCH
button will increase the speed
(x 4), (x 8), (x 15).
(x 8),
of the search
(CD: (x 2),
(x 2),
(x 4),
(x 20))
• To resume normal playback, press PLAY.
Still Playback
Press PAUSE/STILL during
normalplaybacktopauseplay-
back.
To resume normal playback,
press PLAY.
Frame Advance
Press PAUSE/STILL during still playback.
One frame is advanced each time you press PAUSE/STILL.
To resume normal playback, press PLAY.
Slow-motion Playback
Press SLOW
(
)
Reverse or SLOW
(
)
Forward during
normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2,
x1/4, x1/6, x1/7.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE/STILL.
NOTE:
Locating a chapter or track
The unit is capable of holding a still video
image or On screen display image on your
television screen indefinitely. If you leave
the still video image or On screen display
image displayed on your TV for an ex-
tended period of time, you risk permanent
damage to your television screen. Pro-
jection televisions are very susceptible.
Press SKIP(
) Forward or SKIP(
) Reverse during
playback to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is
skipped.
29
5P20521A [E] P27-32
29
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Zooming/Locating desired scene
Zooming
This unit will allow you to zoom in on the frame image. You
can then make selections by switching the position of the
frame.
Press ZOOM during play-
back.
The center part of the
image will be zoomed in.
Each press of ZOOM will
1
1
change the ZOOM
1
(x 1.3),
2 (x 1.5) and
3 (x 2.0).
Press
/
/
/
to view a different part of the frame.
2
3
You may move the frame from the center position to UP,
DOWN, LEFT or RIGHT direction.
In the zoom mode press ZOOM repeatedly to return to a
1:1 view (
Off).
Locating Desired Scene
Use the title, chapter and time recorded on the disc to
locate the desired point to play back.
Press JUMP during play-
back.
1
Jump
Time
Title
Chapter
/Enter/0 9/Cancel/Jump
Press
or
to select the “Time”, “Title” or “Chapter”.
2
3
Press Direct channel selection (0–9) to input the number.
• If you input a wrong number, press CANCEL.
• Refer to the package supplied with the disc to check the
numbers.
NOTES:
• You can select the Pause, Slow or
Search playback in the zoom mode.
• Some discs may not respond to zoom
feature.
Press ENTER.
4
• Playback starts.
• When you change the title, playback starts from
Chapter 1 of the selected title.
• Some discs may not work in the above operation.
30
5P20521A [E] P27-32
30
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat playback
Title, Chapter, Track Playback
Press PLAY MODE during playback or stop mode.
1
2
DVD
CD
Repeat
/Enter/Play Mode
:
Off
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Press
/
or ENTER once or twice to select “Chapter” or “Title”.
to select “Repeat” and then press
or ENTER once or twice to select “Track” or “All”.
DVD
In case of CD, at first press
/
CD
Repeat
/Enter/Play Mode
:
Chapter
Play Mode
Repeat
:
:
Off
All
/Enter/Play Mode
Press PLAY MODE again to make the screen disappear.
3
• Press PLAY to start Repeat playback.
• To resume normal playback, select Repeat Off.
A-B Repeat Playback
A-B repeat playback allows you to repeat material between two
selected points.
Press REPEAT A-B during
playback.
The start point is selected.
1
A
Press REPEAT A-B again.
2
A
B
The end point is selected.
Playback starts at the point that
you selected. Playback stops at
the end point, returns to Point A
automatically, then starts again.
NOTES:
• Some discs may not work with the
repeat operation.
To resume normal playback press REPEAT A-B again.
” appears on the screen.
• In A-B repeat mode, subtitles near
point A or B may not appear.
• During the A-B Repeat Playback the
ANGLE feature will not operate.
• You may not be able to set A-B Re-
peat, depending on the scenes of the
DVD.
“
Off
31
5P20521A [E] P27-32
31
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Program playback/Random playback (CD)
Program playback
You can arrange the order of tracks on the disc.
Press PLAY MODE in the stop
mode.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Press
or
to select “Play
Play Mode
Repeat
:
:
Program
Off
7
8
9
2 Mode” then press
/
or
1
4
10
11
12
ENTER to select “Program”.
2
3
5
6
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
Example: In case you wish to
program in order of 7, 3, 11:
3
Play Mode
Repeat
:
:
Program
Off
7
8
9
Enter as 7
, 3
, 11.
1
2
3
7
3
11
4
5
6
10
11
12
If you input a wrong number,
press CANCEL.
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
Press
/
or
/
to select
4 “Program Playback” and press
Program Playback
Track 7/11
02:31 08:29
ENTER. “Program Playback” will
appear on the screen. The
program you selected will begin
to playback in the order set.
To return to normal playback,
select “Play Mode: Off” at step 2
above.
Random playback
Press PLAY MODE during
1
playback or stop mode.
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Press
or
to select “Play
or
2
3
Play Mode
Repeat
:
:
Random
Off
Mode”, then press
ENTER to select “Random”.
/
NOTES:
/Enter/Play Mode
•
•
•
To cancel program play, select “Clear”
at step 4 and press ENTER.
The program is cancelled when you
open the disc tray or turn the power off.
Random playback can not be
Press PLAY.
“Random Play” will appear on the screen and Random
Playback will start.
To return to normal playback, select “Play Mode : Off” at step
2 above.
combined with Repeat playback.
32
5P20521A [E] P27-32
32
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Marking desired scenes
The TV/DVD stores the points that you
want to watch again. You can resume
playback from that scene.
Marking the Scenes
Press MARKER during
1
Marker
Marker
Marker
1
2
3
playback.
/Enter/Cancel/Marker
Select the blank Marker
2
Marker
Marker
Marker
1
2
3
00 27 54
using
/
, then press
ENTER at the desired
scene.
/Enter/Cancel/Marker
• Up to 3 scenes can be
selected.
• Repeat this procedure to
set the other 2 scenes.
Press MARKER to remove this display.
3
Returning to the Scenes
Press MARKER during
1
Marker
Marker
Marker
1
2
3
00 27 54
01 16 25
02 08 31
playback or stop mode.
/Enter/Cancel/Marker
Press
the Marker 1-3.
or
to select
2
3
Marker
Marker
Marker
1
2
3
00 27 54
01 16 25
02 08 31
/Enter/Cancel/Marker
Press ENTER.
Playback starts from the marked scene.
To Cancel the Mark
Press MARKER.
1
Press
or
to select the Marker 1-3.
2
3
Press CANCEL.
Press MARKER to remove this display.
NOTES:
•
The marking is canceled when you open
the disc tray or turn the power off.
Some subtitles recorded around the
marker may fail to appear. [DVD]
•
33
5P20521A [E] P33-38
33
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing soundtrack language/Subtitles
Changing soundtrack language
You can select the language when you play a multilingual
disc.
Press AUDIO during play-
back.
1
1/8 Eng Dolby Digital
The current soundtrack
language will appear.
Press AUDIO repeatedly
until the desired language
is selected.
2
2/8 Fra Dolby Digital
The on-screen display will
disappear after a few sec-
onds.
Subtitles
Turning the Subtitles On and Off
When playing back a disc recorded with subtitles, you
can turn the subtitles on or off.
Press SUBTITLE during play-
back until “Off” appears.
Off
NOTES:
Changing the subtitle language
• If the desired language is not heard af-
ter pressing AUDIO several times, the
language is not recorded on the disc.
• Changing soundtrack language is can-
celled when you open the disc tray. The
initial default language or available lan-
guage will be heard if the disc is played
back again.
You can select the language when playing back a disc
recorded with multi-lingual subtitles.
Press SUBTITLE repeat-
edly during playback until
your desired language ap-
pears.
1
1/32 Eng
• Changing subtitle language is cancelled
when you open the disc tray.
• Some functions may not work on some
DVDs. You may not be able to turn sub-
titles on or off or change subtitles. While
playing the DVD, the subtitle may
change when:
The on-screen display will disappear after a few seconds.
2
- you open or close the disc tray
- you change the title.
• In some cases, the subtitle language is
not changed to the selected one imme-
diately.
34
5P20521A [E] P33-38
34
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing angles/Title selection/DVD menu
Changing angles
When playing back a disc recorded with multi-angle facil-
ity, you can change the view angle.
Press ANGLE during play-
back.
1
1/9
The current angle will ap-
pear.
Press ANGLE repeatedly until the desired angle is selected.
2
Title selection
Two or more titles are recorded on some discs. If the title
menu is recorded on the disc, you can select the desired
title.
Press TOP MENU during playback.
Title menu appears on the screen.
1
Press
/
or
/
to select the desired title.
2
3
Press ENTER or PLAY.
The playback of the selected title will start.
DVD menu
Some DVDs allow you to select the disc contents using
the menu.
When you play back these DVDs, you can select the sub-
title language and soundtrack language, etc. using the
DVD menu.
Press DVD MENU during playback.
The DVD menu appears on the screen.
1
• Press DVD MENU again to resume playback at the scene
when you pressed DVD MENU.
NOTES:
• Depending on the DVD, you may not
be able to change the angles even if
multi-angles are recorded on the DVD.
• Depending on the DVD, you may not
be able to select the title. Depending
on the DVD, a “title menu” may simply
be called a “menu” or “title” in the in-
structions supplied with the disc.
Press
/
or
/
to select the desired item.
2
3
Press ENTER.
The menu continues to another screen. Repeat steps 2
and 3 to set additional items if any.
35
5P20521A [E] P33-38
35
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the aspect ratio of TV screen/Setting on screen display
Setting the aspect ratio of TV screen
You can select the aspect ratio of the picture.
Press SETUP in the stop mode
or No Disc.
Language Picture Sound Parental Other
1
Press
or
to select “Picture”.
/Enter/Setup/Return
Press
or
or ENTER, then press
to select “Tv Screen”.
Language Picture Sound Parental Other
2
Tv Screen
Display
4:3
On
/Enter/Setup/Return
Language Picture Sound Parental Other
Press
Press
or ENTER.
3
4
Tv Screen
Display
4:3
On
4:3
4:3
or
to select your de-
sired screen type, then press
ENTER.
/Enter/Setup/Return
You have the following screen sizes to choose from:
4:3 Letterbox
When playing back a wide screen-DVD disc, it displays the
wide picture with black bands at the top and bottom of screen.
4:3
Panscan
It displays the wide picture on the whole screen with left
and right edges automatically cut off.
Press SETUP or RETURN to remove the Menu screen.
Status on screen display
On screen display can be switched on or off when you press
the DISPLAY button.
Press SETUP in the stop mode or No Disc.
1
2
Press
or
to select “Picture”.
Language Picture Sound Parental Other
Press
or
or ENTER, then press
to select “Display”.
Tv Screen
Display
4:3
On
Press
“On” or “Off”.
or ENTER to select
3
Language Picture Sound Parental Other
Tv Screen
Display
4:3
Off
NOTE:
It is not always possible for the DVD disc
to display the picture as per your preferred
picture setting - for example, if you select
“4:3 Panscan”, the disc may not offer this
option. In this case the picture would dis-
play in whichever format the disc is capa-
ble of playing back.
On: On screen displays
appear when you press the buttons (factory setting).
Off: On screen displays do not appear when you press
any buttons except SETUP, SEARCH MODE, PLAY
MODE, MARKER and DISPLAY.
Press SETUP or RETURN to remove the menu screen.
4
36
5P20521A [E] P33-38
36
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Dynamic Range Control
DRC (Dynamic Range Control) ena-
bles you to control the dynamic range
so as to achieve a suitable sound for
your equipment.
Press TV/DVD to select
DVD mode.
Language Picture Sound Parental Other
1
Press SETUP in the stop
mode or No Disc.
Press
or
to select
“Sound”.
/Enter/Setup/Return
Press
lect “DRC”.
or ENTER to se-
Language Picture Sound Parental Other
2
3
4
DRC
On
/Enter/Setup/Return
Press
Press
“On” or “Off”.
or ENTER.
or to select
Language Picture Sound Parental Other
On
Off
DRC
On
/Enter/Setup/Return
Press SETUP or RETURN to remove the Menu screen.
NOTES:
• This function works only during play-
back of Dolby Digital recorded discs.
• The level of Dynamic Range Reduction
may differ depending on DVD video
disc.
37
5P20521A [E] P33-38
37
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental control setting
Some discs are specified not suitable
for children. Such discs can be limited
not to play back with the unit.
Press SETUP in the stop
mode or No Disc.
1
Press
or
to select
“Parental”. Then press
or
ENTER.
Press
or
“Parental”, then press
until the level you require
appears.
to select
2
or
• Level Off : The parental control setting does not
function.
• Level 8 : Virtually all DVD software can be played
back.
• Level 1 : DVD software for adults cannot be
played back.
• Select from level 1 to level 8. The limitation will be
more severe as the level number decreases.
Press
“Password”.
Press Direct channel
selection (0-9) to input a
4-digit password.
Be sure to remember this
number!
or
to select
3
4
• If you input a wrong
number, press CANCEL.
Press ENTER to store the
password.
NOTE: Now the rating is
locked and the setting cannot
be changed unless you enter
the correct password.
NOTES:
• If each setup (P. 27, 36~39, 41~43) has
been completed, the unit can always
be worked under the same conditions
Press SETUP or RETURN to remove the Menu screen.
5
(especially with DVD discs).
Each setup will be retained in the
memory when you turn the power off.
• Depending on the discs, the unit cannot
limit playback.
• Some discs may not be encoded with
specific rating level information though its
disc jacket says “adult.” For those discs,
the age restriction will not work.
38
5P20521A [E] P33-38
38
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the parental level
Press SETUP in the stop mode
or No Disc.
1
2
Press
or
to select
“Parental”. Then press
or
ENTER.
Press Direct channel
selection (0-9) to enter the
password you have stored.
• If you input a wrong
number, press CANCEL.
Press ENTER.
The rating is now unlocked.
3
4
Press
“Parental”, then press
to change the parental
level.
or
to select
or
Press
or
to select
5
6
“Password”, then press
Direct channel selection
(0-9) to enter the password.
NOTE: You can change the
password at this time if you
want.
Press ENTER.
The parental level is changed
and locked.
NOTE:
Do not forget the password. If you forget the
password, contact the dealer that you
purchased the unit from.
Press SETUP or RETURN to remove the Menu screen.
7
39
5P20521A [E] P39-46
39
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Temporary disabling of rating level by DVD disc
Depending on the DVD disc, the disc
LoadaDVDdiscandpressPLAY
or OPEN/CLOSE (see page 28).
may try to temporarily cancel the
rating level that you have set.
It is up to you to decide whether to
cancel the rating level or not.
1
If the DVD disc has been designed to temporarily cancel the
Rating level, the screen which follows the “Reading” screen will
change, depending on which disc is played. If you select “YES”
withENTERkey,“Yourdiscexceedstheparentalcontrollevel1.”
(e.g.) screen will then appear.
2
Reading
Your disc exceeds
the parental control level 1.
Parental Control Level
Cancel Picture
/Enter/Return
If you wish to cancel the set rating level temporarily, select
3
“Parental Control Level” with
or , then press ENTER. If the
4-digits password at step 3 on page 38 has been set, the pass-
word entering screen will appear as shown in step 4 below.
Alternatively, if the password has not been set, playback will
commence. If you don’t know (or have forgotten) the password,
select “Cancel Picture”.
The setting screen will disappear. Press OPEN/CLOSE to
remove the disc.
Enter the password with Direct
channel selection (0-9).
Then press ENTER.
4
5
Please enter the
4
digit password
Enter/0 9/Cancel/Return
If you interrupt the entering,
press RETURN.
Playback will commence if the entered password was correct.
NOTE:
This temporary cancellation of rating level
will be kept until the disc is ejected.
When the disc is ejected, the original rat-
ing level will be set again automatically.
40
5P20521A [E] P39-46
40
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting menu language
You can select the language of the
disc menu messages of DVDs.
Press SETUP in the stop mode.
Language Picture Sound Parental Other
1
2
3
Press
or
to select
“Language”.
/Enter/Setup/Return
Press
or ENTER.
Language Picture Sound Parental Other
Then press
“Menu”.
or
to select
Menu
Subtitle
Audio
English
Automatic
English
/Enter/Setup/Return
Press
Press
or ENTER.
or to select your
desired language, then press
ENTER.
English, Francais, Espanol :
The selected language will be heard or seen.
Other:
Other language can be selected (see the “Language code list” on
page 44).
Press SETUP or RETURN to remove the menu screen.
4
41
5P20521A [E] P39-46
41
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting subtitle language
The same subtitle language can
always be selected even if you replace
the disc or turn the power off.
Press SETUP in the stop mode.
Language Picture Sound Parental Other
1
2
3
Press
or
to select “Lan-
guage”
/Enter/Setup/Return
Press
or ENTER.
Then press
“Subtitle”.
or
to select
Press
Press
or ENTER.
or to select your
desired language, then press
ENTER.
English, Francais, Espanol:
The subtitle is displayed with the selected language if it is
recorded on the disc.
Other:
If you want to select another language, enter the language code
(See the Language code list on page 44).
Automatic:
• The unit will automatically select the same language in the
AUDIO setting.
• When the unit selects the same language as the AUDIO, the
subtitles will not appear during playback.
• When you do not use the same language as the AUDIO, the
subtitles will appear during playback.
Off:
Subtitles do not appear.
Press SETUP or RETURN to remove the Menu screen.
4
NOTE:
If the selected language is not recorded
on the disc, the first-priority language is
selected.
42
5P20521A [E] P39-46
42
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting audio soundtrack language
Thesameaudiosoundtracklanguage
Press SETUP in the stop mode.
Press or toselect“Language”.
Language Picture Sound Parental Other
1
2
3
can always be selected by your unit
even if you replace the disc or turn
the power off.
/Enter/Setup/Return
Press
or ENTER.
Then press
“Audio”.
or
to select
Press
Press
or ENTER.
or to select your
desiredAudioLanguage,thenpress
ENTER.
English, Francais, Espanol:
The language you have selected will play if it is recorded on
the disc.
Other:
If you want to select another language, enter the language code
(See the Language code list on page 44).
Original:
The unit will select the first priority language of each disc.
Press SETUP or RETURN to remove the Menu screen.
4
NOTE:
If the selected language is not recorded
on the disc, the original language will
be heard.
43
5P20521A [E] P39-46
43
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Language code list
Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or “MENU LANGUAGE”
(see pages 41~43).
Language Name Code Language Name Code Language Name Code Language Name Code
Abkhazian
Afar
1112 Fiji
1620 Lingala
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
2224 Singhalese 2919
1111 Finnish
1116 French
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2921
2922
2925
1529
Afrikaans
Albanian
Amharic
Arabic
2111 Malayalam
1415 Maltese
1522 Maori
2322 Sundanese 2931
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
2122 Marathi
1724 Moldavian
1731 Mongolian
1811 Nauru
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla 1224 Hebrew
1933 Nepali
2415 Telugu
2425 Thai
Bhutani
Bihari
1436 Hindi
1819 Norwegian
1831 Oriya
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
2629 Tonga
1611 Turkish
2622 Turkmen
2630 Twi
Breton
1929 Panjabi
1924 Pashto, Pushto
1911 Persian
1711 Polish
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
2123 Italian
1930 Portuguese
2011 Quechua
1311 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
2731 Ukrainian
2033 Rhaeto-Romance 2823 Urdu
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
2825 Uzbek
2831 Vietnamese 3219
2923 Volapük
2911 Welsh
1714 Wolof
2928 Xhosa
2918 Yiddish
2924 Yoruba
2914 Zulu
3225
1335
3325
3418
2019
3525
3631
Danish
Dutch
English
Esperanto
Estonian
Faroese
2225 Serbo-Croatian
2211 Shona
1625 Latvian, Lettish 2232 Sindhi
44
5P20521A [E] P39-46
44
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections to other equipment
The exact arrangement you use to interconnect various video and audio components to the TV/DVD is depend-
ent on the model and features of each component. Check the Owner's Manual provided with each component
for the location of video and audio inputs and outputs.
Using an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
including Dolby Digital Surround audio that sounds just like the movie.
Connect an AV amplifier with built-in Dolby Digital decoder, DTS decoder, MPEG decoder or etc as
shown below.
Front
Rear of TV/DVD
Speaker
Subwoofer
TV/DVD
(Right)
UHF/
VHF
Front
Speaker
(Left)
Coaxial Digital Audio Output
Center Speaker
Coaxial digital cable (not supplied)
To Coaxial Digital Audio Input
Surround
Speaker (Left)
Surround
Speaker
(Right)
AV Amplifier with built-in digital surround
decoder as listed above
*
*
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
NOTES:
• When you make the connection above, on the AV Amplifier, do not set DOLBY DIGITAL to DOLBY DIGITAL, or
MPEG to MPEG “ON”. If you do, a loud noise will emit from the speakers possibly causing damage to your
hearing or to the speakers.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
45
5P20521A [E] P39-46
45
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections to other equipment
(Continued)
Using the audio/video inputs
If you connect the TV/DVD to VCR, camcorder or TV game, you can select by pressing INPUT SELECT.
NOTE:
Press INPUT SELECT repeatedly to select the desired mode.
In the DVD mode this key will not
operate.
“LINE” or TV channel will display on the screen.
LINE
1. To connect the TV/DVD to a VCR
Press the INPUT SELECT to select the desired mode to use the TV as a monitor.
Operate your VCR as usual.
VCR
Front of TV/DVD
VIDEO IN
AUDIO IN (R)
AUDIO IN (L)
To Audio/Video OUT
Audio/Video cord (not supplied)
2. To connect the TV to a camcorder
To playback from the camcorder, connect the camcorder to the TV/DVD as shown.
Camcorder
VIDEO IN
To Audio/Video OUT
AUDIO IN (R)
AUDIO IN (L)
Audio/Video cord (not supplied)
3. To connect the TV to a TV Game
The TV/DVD can also be used as a display device for many video games. However, due to the wide variety of different
types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in
the suggested connection diagrams. You'll need to consult each component's Owner's Manual for additional information.
VIDEO IN
AUDIO IN (R)
AUDIO IN (L)
To Audio/Video OUT
Audio/Video cord (not supplied)
46
5P20521A [E] P39-46
46
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception disturbances
Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF
antenna. Outdoor antennas are recommended for best results. The most common types of television
interference are shown below. If one of these symptoms appear when the TV/DVD is connected to a Cable
TV system, the disturbance may be caused by the local Cable TV company broadcast.
IGNITION
Black spots or horizontal streaks may appear, the picture may flutter or
drift. Usually caused by interference from automobile ignition systems,
neon lamps or AC powered tools and appliances such as drills or hair
dryers.
GHOSTS
Ghosts are caused by the television signal following two paths. One is
the direct path and the other is reflected by tall buildings, hills or other
large objects. Changing the direction or position of the antenna may
improve the reception.
SNOW
If the TV/DVD is located far from the TV station, in a fringe reception
area where the signal is weak, small dots may appear in the picture.
If the signal is extremely weak, the installation of a larger external
antenna may be necessary.
RADIO FREQUENCY INTERFERENCE (RFI)
Caused by two-way radios, this type of interference produces moving
ripples or diagonal streaks in the picture. Some cases may cause a
loss of contrast in the picture. Changing the direction and position of
the antenna or installing an RFI filter may improve the picture.
PICTURE SIZE VARIATION
A slight picture size variation is normal when you adjust the CONTRAST
or BRIGHTNESS settings.
CARE AND MAINTENANCE
To prevent fire or shock hazard, disconnect the TV/DVD from the power source before cleaning.
The finish on the cabinet may be cleaned with mild soap and a soft, damp cloth and cared for as other furniture.
Use caution when cleaning or wiping the plastic parts.
47
5P20521A [E] P47-Back
47
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting
Use the following check list for troubleshooting when you have problems with your unit. Consult your local
dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
SYMPTOMS
POSSIBLE SOLUTIONS
PAGE
POWER
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Power is off, check fuse or circuit breaker.
• Unplug unit, then plug it back in.
10
TV/DVD does not operate.
TV BROADCAST RECEPTION
• Station or CABLE experiencing problems, tune to another station. 14
Poor sound or No sound.
• Check Volume adjustments.
• Check for sources of possible interference.
14
47
14
11,12
47
•
Station or CABLE experiencing problems, tune to another station.
• Check antenna or CABLE connections, reorient antenna.
• Check for sources of possible interference.
• Check picture control adjustments.
Poor picture or No picture.
22
• Station or CABLE experiencing problems, tune to another station. 14
• Station signal is weak, reorient antenna to receive weaker station. 11,12
Poor reception on some channels.
• Check for sources of possible interference.
47
•
Station or CABLE experiencing problems, tune to another station. 14
• Make sure channels are set into memory.
• Check picture control adjustments.
• Check antenna or CABLE connections, reorient antenna.
• Check for sources of possible interference.
18
22
11,12
47
Poor color or no color.
14
18
–
•
Station or CABLE experiencing problems, tune to another station.
• Make sure channels are set into memory.
• CABLE company is scrambling signal.
• Check antenna orientation.
• Check all CABLE connections.
• Set TV/CABLE menu option to the CABLE mode.
• Station or CABLE system problems, try another station.
Picture wobbles or drifts.
No Cable TV reception.
11
12
17
14
Horizontal or diagonal bars on
screen.
• Check antenna connections, reorient antenna.
• Check for sources of possible interference.
11,12
47
•
Make sure TV/CABLE menu option is in the appropriate mode.
17
11
No reception above channel 13.
• If using antenna, check UHF antenna connections.
• No broadcast on station tuned.
• Sleep Timer is set.
• Power interrupted.
14
15
–
TV shuts off.
• TV station experiencing problems or program tuned is not closed
captioned. Try another channel.
14
• Check CABLE connection or VHF/UHF antenna, reposition or 11,12
rotate antenna.
Closed - Caption is not activated.
• Press TV/CAP/TEXT button to turn on the closed caption de-
coder.
16
Display is not shown in your
language.
• Select proper language in the menu options.
13
48
5P20521A [E] P47-Back
48
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPTOMS
POSSIBLE SOLUTIONS
PAGE
DVD
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play CD-ROMs, etc.
28
25
–
Playback doesn’t start.
No picture.
• TV/DVD selector is not set correctly.
26
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
• Select the correct Audio Output position on AV amplifier.
–
29
45
No sound.
Picture is distorted during CUE or • The picture will be distorted occasionally.
REVIEW.
–
Stopping playback, search, slow-
motion play, repeat play, or
program play, etc. cannot be
performed.
• Some discs may not do some of the functions.
–
No 4:3 picture.
• The setup does not match your TV.
• Select Display On.
36
36
45
No on-screen display.
No surround sound.
• The setup does not match your stereo system.
The unit or remote operation key
is not functioning.
• Turn off the unit and unplug the AC power cord for several min-
utes, then replug it.
–
Playback does not start when the
title is selected.
• Check the RATING LEVEL setup.
38~40
Audio soundtrack and/or subtitle
language is not changed when
you play back a DVD.
• Multilingual language is not recorded on the DVD disc.
41
• Some discs have no subtitles.
• Subtitles are cleared. Press SUBTITLE.
No subtitle.
34
Angle cannot be changed.
• Multi-angles are not recorded on the DVD disc.
• The function is prohibited with the unit or the disc.
35
28
“
” appears on the screen.
REMOTE CONTROL
• Aim at the remote control at the remote sensor.
• Operate within Approx. 5 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
The remote control does not
function.
10
DEGAUSSING SYSTEM
This television has a degaussing circuit that will clear up color distortions on the TV screen that
are caused by any excess magnetism which happens to get too close to the TV. This circuit is
designed to operate once when the set is first plugged in. If minor color distortions are seen in
some locations on the screen, please unplug the TV for approximately 15 minutes. When the TV
is plugged back in, the degaussing circuit will operate once to clear up any color distortions.
Repeat this procedure any time the TV screen is accidentally magnetized, or when the TV is
moved or relocated.
49
5P20521A [E] P47-Back
49
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
GENERAL
AC 120 V 60 Hz
Power supply:
Operation: 75 W
Power consumption:
Stand by: 5 W
24.3 lbs (11 kg)
Weight:
Width : 14-1/4 inches (362 mm)
Height: 15-1/16 inches (382 mm)
Depth : 14-3/8 inches (365 mm)
5°C - 40°C
Dimensions:
Operating temperature:
Operating humidity:
Less than 80%
TELEVISION
Picture tube:
13” (335 mm diagonal)
Quartz PLL Frequency Synthesized
Tuner type:
VHF
UHF
2-13
14-69
Receiving channels:
Cable TV 14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
VHF/UHF In 75 ohm coaxial
1.5" (38mm) x 2.7" (69mm) 8 ohm x 2
1.5 W + 1.5 W
Antenna input:
Speaker:
Audio output power:
DVD/CD player
Signal system:
Applicable disc:
NTSC
1. DVD (12 cm, 8 cm)
2. CD (12 cm, 8 cm)
Below Measurable Level
Video : (RCA) 1 Vp-p/75 ohm
Audio : (RCA) –8 dBm/50K ohm
0.5 Vp-p 75 ohms terminated
CD : Wavelength: 770 - 800 nm
Maximum output power: 0.7 mW
DVD : Wavelength: 645 - 660 nm
Maximum output power: 0.5 mW
Wow and flutter:
Input:
Digital audio out:
Pickup:
Remote control
ACCESSORIES:
Telescopic Antenna
50
5P20521A [E] P47-Back
50
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
5P20521A [E] P47-Back
51
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
5P20521A [E] P47-Back
52
5/12/04, 2:43 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
90 Day Full Warranty
If this product experiences any failure due to a defect in material or workmanship within 90 days
from the date of purchase, return it to your nearest Sears Parts & Repair Center, and Sears will
repair it free of charge.
After 90 days and until one (1) year from the date of purchase, Sears will replace defective parts
free of charge. You pay for labor.
After 90 days and until two (2) years from the date of purchase, Sears will replace the Picture
Tube if it is defective. You pay for labor.
This warranty applies only if this (product) is used for private household purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
5P20521A [E] P47-Back
53
5/12/04, 2:44 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPAÑOL
El símbolo del rayo dentro de un
triángulo equilátero tiene por finalidad
alertar al usuario acerca de la
presencia de tensión peligrosa (sin
aislación) en el interior del producto,
que puede tener la intensidad suficiente
como para constituir un riesgo de
descarga eléctrica.
PRECAUCION
RIESGO DE DESCARGA
ELECTRICA NO ABRIR
AVISO: PARA REDUCIR EL RIESGO DE DESCARGA
ELECTRICA, NO RETIRE LA CUBIERTA (O
POSTERIOR). EN EL INTERIOR DEL APARATO
NO HAY COMPONENTE ALGUNO QUE
El signo de exclamación dentro de un
triángulo equilátero tiene por finalidad
alertar al usuario de importantes
instrucciones de operación y
mantenimiento (servicio) en la literatura
que acompaña a este aparato.
PRECISE SERVICIO DE MANTENIMIENTO A
CARGO DEL USUARIO. SOLICITE CUALQUIER
OPERACION DE MANTENIMIENTO A PER-
SONAL DE SERVICIO CALIFICADO.
AVISO:Para reducir el riesgo de incendio o descarga eléctrica, no exponga esta unidad a la lluvia ni a la
humedad.
NOTA: Por favor guarde todo el material de embalaje durante por lo menos 90 días en caso de que
necesite devolver este producto a su lugar de compra o Memorex.
ADVERTENCIA: Este equipo ha sido sometido a pruebas y cumple con los límites establecidos para un aparato
digital de Clase B, de acuerdo con la Parte 15 del Reglamento de la FCC. Estos límites están
diseñados para proporcionar protección razonable contra interferencias perjudiciales en una
instalación residencial. Este equipo genera o emplea energía de radiofrecuencia y, si no es
instalado y empleado de acuerdo con estas instrucciones, puede causar interferencias
perjudiciales a las radiocomunicaciones.
Sin embargo, no garantizamos que no ocurrirán interferencias en una instalación en particular.
Si este equipo causa interferencias perjudiciales a la recepción radial o televisiva, situación que
puede ser determinada apagando y encendiendo el equipo, se sugiere al usuario que trate de
corregir tal interferencia mediante una o más de las siguientes medidas:
- Reorientar o relocalizar la antena receptora.
- Incrementar la separación entre el equipo y el receptor.
- Conectar el equipo a un tomacorriente o circuito diferente al que está conectado al receptor.
- Consultar con el concesionario o un técnico experimentado solicitándole su asistencia.
PRECAUCION: El usuario corre el riesgo de perder la autorización para hacer funcionar este equipo en caso de
que ejecute un cambio o modificación no aprobado por la parte responsable para la
conformidad con las Reglas FCC.
Lugar de la marca requerida
PRECAUCION:
La hoja de especificaciones y las
precauciones para su seguridad están
SISTEMA LASER.
ESTE TOCADISCOS DE VIDEO DIGITAL UTILIZA UN
en la parte trasera del aparato.
PARA UTILIZAR CORRECTAMENTE ESTE PRODUCTO, LEA
CUIDADOSAMENTE ESTE MANUAL DE INSTRUCCIONES Y
GUARDELO PARA SU REFERENCIA EN EL FUTURO. SI
FUERA NECESARIO HACER UN MANTENIMIENTO DE
ESTE APARATO, CONSULTE CON UN CENTRO DE
SERVICIO AUTORIZADO-LEA EL PROCEDIMIENTO DE
SERVICIO.
EL USO DE LOS CONTROLES, AJUSTES O LA
REALIZACION DE OTROS PROCEDIMIENTOS QUE NO
SEAN LOS ESPECIFICADOS AQUI PUEDE PROVOCAR
UHF/
VHF
UNA EXPOSICION A RADIACIONES PELIGROSAS.
PARA EVITAR LA EXPOSICION DIRECTA A LOS RAYOS
LASER, NO TRATE DE ABRIR LA CAJA. PUEDE HABER
CERTIFICACION: CUMPLE CON LAS
UNA RADIACION LASER VISIBLE AL ABRIR LA CAJA.
NORMAS DE PRESTACIONES CON
NO MIRE HACIA EL RAYO.
RADIACION DE LA FDA, 21 CFR
SUBCAPITULO J.
2
5P20521A [S] (02-05)
2
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA SU SEGURIDAD
1. LEA LAS INSTRUCCIONES
Antes de usar la unidad, lea detenidamente todas las instrucciones de seguridad y operación.
2. CONSERVE ESTE MANUAL DE INSTRUCCIONES
Conserve las instrucciones de seguridad y operación para consultas futuras.
3. RESPETE LAS ADVERTENCIAS
Observe estrictamente todas las advertencias impresas en la unidad y las incluidas en el manual de instrucciones.
4. SIGA LAS INSTRUCCIONES
Siga todas las instrucciones de operación y uso.
5. LIMPIEZA
Antes de limpiar este videograbador, desconéctelo del tomacorriente mural. No use limpiadores líquidos ni
aerosol. Utilice sólo un paño húmedo para limpiar el exterior del mueble.
6. ENCHUFES
El fabricante de esta unidad no hace ninguna recomendación de accesorios ya que pueden ser peligrosos.
7. AGUAY HUMEDAD
No utilice este aparato cerca del agua. Por ejemplo cerca de una bañera, lavabo, pileta de la cocina,
lavadero, en un sótano húmedo o cerca de una piscina.
AVISO PARA CARRO PORTATIL
8. ACCESORIOS
(símbolo provisto por RETAC)
No instale esta unidad en un carro, soporte, trípode o mesa inestables. La
unidad podría caerse, causando serias lesiones, resultando también
severamente dañada a la unidad.
8A. La combinación de aparato y carro deberá ser movida con cuidado. Las
detenciones bruscas, la fuerza excesiva y las superficies disparejas podrán
hacer que el aparato y el carro se vuelven.
9. VENTILACION
S3126A
Las ranuras y aberturas en la parte trasera o inferior del mueble son para
ventilación y permiten un funcionamiento fiable de la unidad, protegiendo contra calentamiento excesivo.
Estas aberturas no deberán ser bloqueadas ni cubiertas. Para evitar bloquear las aberturas, nunca sitúe la
unidad encima de una cama, sofá, alfombra u otra superficie similar. Tampoco instale la unidad cerca o
encima de un radiador o calefactor. La unidad no deberá ser instalado en un mueble empotrado, como ser
una repisa para libros o bastidor, a menos que se pueda garantizar una ventilación adecuada, o cuando las
instrucciones
del fabricante así lo especifiquen.
10. FUENTES DE ALIMENTACION
Esta unidad sólo deberá ser operada mediante el tipo de fuente de alimentación especificado en la
etiqueta indicadora. Si no está seguro del tipo de fuente de alimentación que tiene en su casa, consulte a
su distribuidor o a la compañía de electricidad local. En el caso de unidades diseñadas para
funcionar a pilas o con otras fuentes de alimentación, consulte el manual de instrucciones respectivo.
11. CONEXIÓN A TIERRA O POLARIZACION
Esta unidad está equipada con una clavija polarizada de corriente alterna (una clavija que tiene una espiga
más ancha que la otra). Esta clavija solamente puede ser insertada en el tomacorriente en una sola
dirección. Esta es una medida de seguridad. Si no pudiera insertar completamente la clavija en el
tomacorriente, vuelva a intentarlo invirtiendo la clavija. Si aún no fuera posible insertar la clavija, tome
contacto con un electricista para que reemplace su tomacorriente obsoleto. Si su unidad está equipada con
una clavija de conexión a tierra de 3 alambres (una clavija con una tercera espiga de conexión a tierra), no
modifique las características de seguridad de la clavija polarizada. Este tipo de clavija sólo puede ser
insertado en un tomacorriente con contacto a tierra. Esto también es una medida de seguridad. Si no
pudiera insertar la clavija en el tomacorriente, tome contacto con un electricista para que reemplace su
tomacorriente obsoleto. No modifique las características de seguridad de la clavija de conexión a tierra.
3
5P20521A [S] (02-05)
3
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA SU SEGURIDAD
(CONTINUACION)
12. PROTECCION DEL CABLE DE ALIMENTACION
Los cables de alimentación deberán ser tendidos de manera tal que la probabilidad de que sean pisados o
aplastados por otros objetos sea mínima. Preste especial atención a las clavijas de los cables, a los
receptáculos, y al punto por donde salen del aparato.
13. TORMENTAS ELECTRICAS
Como medida de protección durante tormentas eléctricas, o cuando el videograbador permanezca sin uso
durante períodos prolongados de tiempo, desconéctelo del tomacorriente mural y desconecte la antena o
el sistema de cable. Esto evitará que la unidad resulte dañada por tormentas eléctricas o sobretensiones
en la línea de alimentación.
14. LINEAS DE ALIMENTACION
Una antena exterior no deberá ser instalada en la cercanía de líneas de alimentación aéreas ni de otros
circuitos de iluminación eléctrica o potencia, o donde pueda caerse y hacer contacto con tales líneas o
circuitos. Al instalar un sistema de antena exterior, tenga mucho cuidado de no tocar tales líneas o circuitos
de alimentación, ya que el contacto con ellos podría ser fatal.
15. SOBRECARGA
No sobrecargue los tomacorrientes murales ni los cables de extensión, ya que esto podría causar
incendios o descargas eléctricas.
16. ENTRADA DE OBJETOS Y LIQUIDOS
Nunca introduzca objetos de ningún tipo por las aberturas de la unidad, ya que podría tocar peligrosos
puntos de alta tensión o piezas de cortocircuito, provocando incendios o descargas eléctricas. Nunca
derrame ni rocíe ningún tipo de líquido sobre la unidad.
17. CONEXION A TIERRA DE LA ANTENA EXTERIOR
Si se conecta una antena externa o sistema de cable a la unidad, cerciórese de que el sistema de antena o
cable está conectado a tierra para darle protección contra sobretensión y acumulación de carga estática.
La Sección 810 del Código Nacional de Electricidad, ANSI/NFPA 70, entrega información acerca de la
manera correcta de conectar a tierra el mástil y la estructura soportante, puesta a tierra del alambre de
entrada a una unidad de descarga de antena, tamaño de los conductores de puesta a tierra, ubicación de la
nidad de descarga de la antena, conexión a los electrodos de tierra, y requisitos para el electrodo de tierra.
18. SERVICIO
No intente reparar la unidad usted mismo; al abrir o retirar las cubiertas usted se expondrá a alta tensión y
a otros peligros. Solicite todo servicio a personal calificado.
19. DAÑOS QUE REQUIERAN REPARACION
En los siguientes casos, desconecte la unidad del tomacorriente mural y llame a un técnico de servicio
calificado:
a. Cuando el cable de alimentación o la clavija estén dañados.
b. Si se ha derramado líquido sobre la unidad, o si algún objeto ha caído dentro del videograbador.
c. Si la unidad ha sido expuesta a la lluvia o al agua.
d. Cuando a pesar de haber seguido las instrucciones de operación, la unidad no funcione normalmente.
Ajuste solamente los controles indicados en el manual de instrucciones; el ajuste incorrecto de otros
controles podrá causar daños a la unidad, la que por lo general requerirá de un prolongado trabajo
de reparación (por un técnico calificado) para que sus condiciones normales de operación puedan
ser restablecidas.
e. Si la unidad se ha caída o si el gabinete se ha dañado.
f. Cuando la unidad muestre un cambio notorio en su rendimiento.
20. PIEZAS DE REPUESTO
Cuando sea necesario reemplazar piezas, asegúrese de que el técnico de servicio emplee las piezas de
repuesto especificadas por el fabricante, o piezas que tengan las mismas características que las piezas
originales. Los cambios no autorizados podrán causar incendios, descargas eléctricas y otros problemas.
21. REVISION DE SEGURIDAD
Al finalizar cualquier servicio de mantenimiento o reparación de esta unidad, solicítele al técnico que
efectúe comprobaciones de seguridad para determinar si el videograbador se encuentra o no en
condiciones óptimas de operación.
22. CALOR
El producto debe ser situado lejos de fuente de calor como radiadores, reguladores de calefacción, estufas o
otros productos (incluyendo amplificadores) que se producen calor.
23. BANDEJA DEL DISCO
Tenga cuidado de no introducir los dedos en la bandeja del disco cuando se esté cerrando. Puede recibir
heridas graves.
24. CONEXION
Cuando conecte el producto a otro equipo, desconecte la alimentación y desenchufe todos los equipos del
tomacorriente. Si no lo hace, puede provocar una descarga eléctrica y heridas graves.
Lea cuidadosamente el manual de instrucciones del otro equipo y respete las instrucciones al hacer las
conexiones.
25. VOLUMEN DEL SONIDO
Reduzca el volumen a su nivel mínimo antes de conectar el producto. De lo contrario, un volumen alto
puede lastimar sus oídos o en los altavoces.
4
5P20521A [S] (02-05)
4
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
26. DISTORSION DEL SONIDO
No permita que el producto emita un sonido distorsionado durante un periodo de tiempo prolongado.
Puede provocar un calentamiento excesivo del altavoz que resulte en un incendio.
27. ALTAVOCES
Cuando utilice altavoces, mantenga el volumen a un nivel moderado. Si utiliza los altavoces continuamente
a un volumen alto, puede lastimar sus oídos.
28. RAYO LASER
No mire por la ranura de la bandeja del disco por las salidas de circulación de aire del producto para ver la
fuente del rayo láser. Puede causar daños en los ojos.
29. DISCO
No utilice un disco rayado, deformado o reparado. Estos discos se pueden romper fácilmente y provocar
serias heridas o averías en el producto.
30. NOTA PARA LA PERSONA QUE INSTALE EL SISTEMA CABLE TV
Se ha incluido este recordatorio para llamar la atención de quien instale el sistema CABLE TV, con
respecto al Artículo 820-40 de la NEC, que entrega directivas de guía para realizar una conexión adecuada
a tierra y, en particular, especifica que el cable de puesta a tierra debe ser conectado al sistema de
conexión a tierra del edificio, lo más cerca del punto de entrada del cable como sea posible.
EJEMPLO DE CONEXION A TIERRA DE LAANTENA
SEGUN EL CODIGO NACIONAL DE ELECTRICIDAD
ALAMBRE DE ENTRADA DE LA ANTENA
ABRAZADERA
DE TIERRA
UNIDAD DE DESCARGA DE LAANTENA
(NEC, SECCION 810-20)
CONDUCTORES DE PUESTAA
TIERRA (NEC, SECCION 810-21)
EQUIPO DE SERVICIO
ELECTRICO
ABRAZADERAS DE TIERRA
SERVICIO DE ALIMENTACION DE SISTEMA
NEC - CODIGO NACIONAL DE ELECTRICIDAD
ELECTRODO DE PUESTA A TIERRA
(NEC ART 250, PARTE H)
S2898A
CONDENSACION
Se condensará humedad en la sección de funcionamiento del tocadiscos si se lo trae de un lugar fresco a una
habitación caliente o si la temperatura en la habitación sube repentinamente. En este caso, se verán afectadas
las prestaciones del tocadiscos. Para evitarlo, deje el tocadiscos a la nueva temperatura durante
aproximadamente una hora antes de conectarlo, o haga que la temperatura en la habitación suba gradualmente.
También puede condensarse humedad durante el verano si el tocadiscos está expuesta a una corriente de aire
del acondicionador de aire. En estos casos, cambie el lugar donde está instalado el tocadiscos.
5
5P20521A [S] (02-05)
5
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Caracteristicas
TV a Color con Tocadiscos de DVD/CD
Diseño único ahorra-espacio que combina un TV a color de 13" con un tocadiscos DVD/CD.
El disco DVD tiene mucha más capacidad, pero es del mismo tamaño que los discos compactos de audio.
Lacalidad de imagen/audio del DVD supera la calidad de los otros software. La calidad de imagen es mayor quela del
Super VHS. La calidad el audio es mayor que la de los discos compactos de audio.
El DVD también tieneopciones especiales; selección de idioma de audio, selección de idioma de subtítulos o múltiples
ángulos parauna misma escena, etc. El TOCADISCOS DE DVD puede reproducir los discos compactos de audio.
Alta calidad de imágenes
Resolución horizontal
Más de 500 líneas. Supera la resolución del Super VHS (400 líneas) o discos láser (430 líneas).
Compatible con una gran gama de salidas de audio DVD
Toma de audio digital coaxial
• Cuando se conecta un equipo con un decodificador Dolby Digital integrado, los sonidos en Dolby Digitalpueden
producir el efecto de estar en un cine o en una sala de conciertos.
• Audio surround estándar diferente al Dolby Digital. Este formato ya se utiliza en varios cines. Al conectar esta unidad a
un decodificador DTS o a un amplificador AV con decodificador DTS integrado, se puede disfrutar del audio DTS de los
discos DVD grabados en este formato. Sin embargo, el audio no saldrá de los jacks análogos de salida de audio.
• Mediante la conexión de este aparato a un amplificador AV con un decodificador MPEG integrado, podrádisfrutar del
audio MPEG de los discos DVD que están grabados en este formato.
• El sonido PCM Lineal de 48 kHz/24 bit por 96 kHz/24 bit supera el sonido de los discos compactos de audio.
Funciones convenientes
Selección directa de sus escenas deseadas, utilizando el Título/Capítulo/Tiempo/Canción - Puede reproducir la
escena deseada.
Llamada de hasta 3 escenas (sólo DVD) - Puede programar hasta 3 escenas en la memoria y llamar las escenas marcadas.
Avance de cuadros - El PAUSE/STILL mueve un cuadro a la vez.
Cámara lenta - La opción SLOW es para avanzar o retroceder en el programa mediante 4 pasos de 1/7-1/2 veces.
Reproducción repetida - Se puede repetir el capítulo, canción, título, lados o el material entre dos puntos seleccionados.
Reproducción programada (disco compacto de audio) - Se pueden reproducir canciones en una secuencia programada.
Zoom (sólo DVD) - Se puede acercar con un zoom sobre el sujeto seleccionado en la escena durante la reproducción.
Nota: Compruebe si los discos tienen las siguientes funciones.
Múltiples idiomas - Puede reproducir con un máximo de 32 idiomas para los subtítulos y un máximo de 8 idiomas para
la pista de sonido para sus películas o programas.
Múltiples ángulos - Las imágenes de los deportes o conciertos en vivo se graban con muchas cámaras. Cuando
reproduzca estos discos, puede cambiar de ángulo durante la reproducción.
Control para mayores de edad - Puede restringir la reproducción de escenas o sonidos de los discos DVD para
mayores de edad, que tienen un nivel de control por los padres.
Relación de aspecto del video - Puede cambiar la relación de aspecto de la pantalla de acuerdo al formato de su monitor.
Características de la TV
Capacidad para 181 canales - Recibe un máximo de 113 canales de cable con emisiones estandares VHF y UHF. El
número real de canales que se pueden recibir depende de la recepción de canales en su área o de su sistemade cable.
Descodificador de leyendas codificada con modo de texto completo - Muestra las leyendas de los textos o eltexto
del programa en pantalla completa para las personas con problemas de audición.
Ajustes de imagen utilizando el controlador remoto - La indicación en pantalla permite el ajuste preciso de BRIGHT-
NESS (brillo), COLOR, CONTRAST (contraste), SHARPNESS (definicion) y TINT (tinte), con el controlador remoto.
Temporizador programable de TV - Puede ser operado con el control remoto y el TV puede ser programadohasta en
120 minutos para que se apague automáticamente.
Indicación en pantalla de 3 lenguas - Usted puede seleccionar una de 3 lenguas, inglés, español o francés
porprogramación en pantalla.
Chip V - La función de prohibición para menores con Chip V puede leer la clasificación de un programa de TV opelícula,
si el programa tiene codificada esta información. El Chip V permite seleccionar el nivel de prohibición.
Este producto incorpora una tecnología de protección de derechos de autor, que a su vez está protegida
pordeterminadas patentes de los EE UU y otros derechos de propiedad intelectual propiedad de
MacrovisionCorporation y otros propietarios de dichos derechos. El uso de esta tecnología protegida por los
derechos de autor debe estar autorizada por Macrovision Corporation y es exclusivamente para uso doméstico
y otros usos limitados a menos que sea autorizado de otra manera por Macrovision Corporation.
Se prohibeel desarmado y el estudio de su diseño para copiarlo.
6
5P20521A [S] (06-10)
6
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Indice
Antes de utilizear su aparato
PARA SU SEGURIDAD ....................................................... 3
Caracteristicas ..................................................................... 6
Indice.................................................................................... 7
Partes y sus funciones ......................................................... 8
Control remoto ..................................................................... 9
Fuente de alimentación...................................................... 10
Conexiones de la antena ................................................... 11
Conexiones de TV cable .................................................... 12
Operacion del TV
Seleccion de idioma en pantalla ........................................ 13
Operacion del TV ............................................................... 14
Subtítulo cerrado ................................................................ 16
Para memorizar canales .................................................... 17
Seleccion Chip-V................................................................ 19
Ajustes de control de imagen............................................. 22
Ajuste de la preferencia de imagen.................................... 23
Segundo programa de sonido (SAP) y estereo ................. 24
Función de reproducción
Disco .................................................................................. 25
Preparación/Estado del disco ............................................ 26
Ajuste de la selección de idioma........................................ 27
Procedimiento de reproducción ......................................... 28
Reproducción especial ....................................................... 29
Función de adelantada
Zoom/Búsqueda de la escena deseada............................. 30
Reproducción repetida ....................................................... 31
Programación de reproducción/
Reproducción aleatoria (disco compacto)............................ 32
Marcación de escenas deseadas....................................... 33
Cambio del idioma de la pista de sonido/Subtítulos .......... 34
Cambio de ángulos/Selección de título/Menú DVD ........... 35
Información adicional
Ajuste del formato (relación de aspecto) de la pantalla
de la TV/Ajuste de la visualización en pantalla .................. 36
Control de Gama Dinámica................................................ 37
Ajuste de restricciones para menores................................ 38
Cambio del nivel de restricciones para menores ............... 39
Deshabilitación temporal del nivel de rating (clasificación)
del disco DVD..................................................................... 40
Selección del idioma del menú .......................................... 41
Selección del idioma de los subtítulos ............................... 42
Selección del idioma de la pista de sonido de audio ......... 43
Lista de códigos de idiomas............................................... 44
Conexiones de toma Audio/Video...................................... 45
Disturbios de recepcion...................................................... 47
Problemas y localización de averías.................................. 48
Especificaciones ................................................................ 50
7
5P20521A [S] (06-10)
7
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Partes y sus funciones
Delantera
Bandeja del disco
Indicador POWER
Interruptor de
Botones de salto (SKIP)
alimentación (POWER)
Toma de auriculares
Tomas AUDIO IN
(L/R)
Sensor de control
remoto
Toma VIDEO IN
Botón de apertura/cierr
(OPEN/CLOSE)
Botón parada (STOP)
Botones de volumen
(VOLUME ▲/▼)
Botón reproducción
(PLAY)
Botones selectores de canal
(CHANNEL ▲/▼)
Trasera
Toma RF IN
UHF/
VHF
UHF/
VHF
Toma COAXIAL DIGITAL AUDIO OUT
Cordón de CA
8
5P20521A [S] (06-10)
8
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Remoto
Página
POWER
Conexión/Desconexión
13,14,26,28
15
DISPLAY/CALL
Consultar información de la TV
Consultar información del DVD
Cambiar entre TV/AV y DVD
Abra o cierre la bandeja
Dirigir selección de canales de la TV
Introducir ajuste
26
TV/DVD
OPEN/CLOSE
0-9
26,27,37
28,40
14,18
30,32
19,21,38~40
14
Entre una contraseña
VOL +/–
MUTE
Ajustar volumen de TV
Quitar el sonido
15
SLEEP
Desactivación Automática (Sleep Timer)
Seleccionar canal de TV
15
15
CH
/
Botones de cursor
13,17~23,27,28,30~33
36~43
SELECT/ENTER Introducir información en el menú 13,19,20~23,27,28
30~33,35~43
CANCEL
Resetear información en el menú 19,21,22,30,32
33,38,39
SETUP/TV MENU Mostrar el menú de la TV
13,17~23
Llamar el modo de ajuste inicial 27,36~39,41~43
DVD MENU
TOP MENU
Mostrar el menú del DVD
Seleccione el título
35
35
29
SEARCH 8/9 Reproducción en avance/retroceso rápidos
PLAY A
Reproducción
28,29,31,32,35,40
SKIP
/
Salte el capítulo en avance o retroceso
Mostrar subtítulos
29
34
28
29
29
SUBTITLE
STOP
Parada
SLOW
/
Avance/retroceso-cámara lenta
Pausa sonido del CD
PAUSE/STILL
Fijar imagen del DVD
PLAY MODE
RETURN
REPEAT A-B
ANGLE
Seleccione el modo de reproducción
Quitar el menú del DVD
31,32
27,36~43
Repita la reproducción entre A y B
Cambie el ángulo de reproducción
Cambiar el sonido de la TV
Cambie el idioma de la pista de sonido
Indice
31
35
24
34
33
30
AUDIO
MARKER
JUMP
Localización de la escena deseada
Cambiar entre TV/Caption/Text
Modo Caption Cerrado
TV/CAP/TEXT
16
15
30
46
QUICK VIEW/ZOOM Cambiar entre el canal actual/anterior
Zoom
INPUT SELECT
Cambiar entre TV/AV
ATENCIÓN
Si adquiere un mando a distancia universal
en su distribuidor local, póngase en
contacto con el fabricante del mismo para
solicitar el código de programación
requerido.
9
5P20521A [S] (06-10)
9
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Control remoto
(Continuacion)
Coloque las pilas
Abrir la tapa del compartimento
de las pilas siguiendo la
dirección de la flecha.
Coloque dos pilas “AAA”,
Recoloque la tapa del
compartimiento.
1
2
3
(on suministradas) prestando
atención a las marcas de polaridad
en el compartimiento de las pilas.
Funcionamiento
• Apunte el mando a distancia al sensor remoto y presione los botones de
control para hacer funcionar.
• Utilice el control remoto dentro de un ángulo de 30˚ hacia ambos lados
del sensor remoto, hasta una distancia de unos 5 metros.
Aproximadamente15PIES(5m)
NOTAS:
•
•
No deje la unidad de control remoto expuesta a la luz solar directa, ni en lugares cálidos o húmedos.
La unidad de control remoto utiliza rayos infrarrojos para transmitir señales, por lo que el reflejo de la luz solar
o luz fluorescente en el sensor remoto puede reducir la distancia de funcionamiento.
El uso incorrecto de las pilas puede provocar una fuga o estallido. Lea las advertencias de las pilas y
utilícelas correctamente.
•
•
•
No mezcle pilas antiguas y pilas nuevas.
Extraiga las pilas si no va a utilizar el control remoto durante un largo período de tiempo.
Fuente de alimentación
PARA UTILIZAR CORRIENTE ALTERNA (CA)
Tomacorriente de CA
Utilice el cable de CA polarizado sumistrado para CA operación.
Conecte el enchufe pequeño en el extremo del cable al conectador
de entrada de CA en el parte trasera del TV/DVD, luego inserte el
enchufe más ancho de cable de CA en un tomacorriente de CA de
120V, 60Hz polarizado.
Orificio y hoja
más anchos
NOTAS:
• Nunca conecte el enchufe cordon de CA a otro voltaje que no
sea el especificado (120V 60Hz).
Utilice solamente el cordon eléctrico suministrado.
• Si el cordon de CA polarizada no se ajusta en un tomacorriente
de CA no polarizada, no intente limar o cortar las clavijas.
Es responsabilidad de usuario hacer que un electricista
reemplace el tomacorriente inadecuado.
• Si usted causa una descarga estática cuando toca la undad y
este falla, simplemente desenchufe la unidad del tomacorriente,
espere algunos minutos y enchufela otra vez. La unidad deberá
Cable de corriente alterna polarizado
(una pata es más ancha que la otra.)
funcionar normalmente.
10
5P20521A [S] (06-10)
10
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones de la antena
Si usted está utilizando una antena para interiores o exteriores, siga las instrucciones de abajo que
correspondan a su sistema de antena. Si está utilizando el servicio de TV cable (CABLE), vea la página
12 para las conexiones de TV cable.
Antena combinada de VHF/UHF (Cable único de 75 ohmios o cable con doble
conductor de 300 ohmios)
Conecte el cable de 75 ohmios de la antena
combinada de VHF/UHF en el jack de la antena.
Si su antena combinada de VHF/UHF posee un
cable de dos conductores de 300 ohmios, es posible
que sea necesario utilizar un transformador de
adaptación de 300-75 ohmios.
Jack de
antena
Jack de
antena
Cable
coaxial de
75 ohmios
Transformador de
adaptacion de 300-
75 ohmios
Antena combinada de VHF/UHF (Cables de 300 ohmios independientes de dos
conductores de VHF y de UHF)
Conecte el cable de dos conductores de 300 ohmios
de UHF en el combinador (no suministrado).
Conecte el cable de dos conductores de 300 ohmios
Transformador de
adaptacion de
de VHF en el transformador de adaptación de 300-
300-75 ohmios
75 ohmios. Conecte el transformador al combinador,
y luego conecte el combinador al jack de la antena.
Jack de
antena
Combinador
UHF 300 ohmios
VHF 300 ohmios
Antenas independientes de VHF/UHF (cable de VHF de 75 ohmios y cables de dos
conductores UHF de 300 ohmios)
Conecte el cable de 75 ohmios de VHF y el cable
de dos conductores de 300 ohmios de UHF al
combinador (no suministrado). Conecte el
combinador en el jack de la antena.
VHF 75 ohmios
Jack de
antena
Combinador
UHF 300 ohmios
11
5P20521A [S] (11-16)
11
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones de TV cable
Este TV/DVD posee amplios límites de sintonización y puede ser sintonizado a la mayoría de los canales
de cable sin utilizar una caja convertidora de TV cable. Algunas de las compañías de TV cable ofrecen
“canales pagados premiados” en los cuales la señal ha sido codificada. La decodificación de estas
señales para la recepción normal requiere el uso de un mecanismo decodificador que lo suministra
generalmente la compañía de cable.
PARA ABONADOS AL SERVICIO BASICO DE TV CABLE
Para el servicio básico de cable y cuando no es necesario un
convertidor/caja decodificadora, conecte el cable coaxial de 75
ohmios de al jack de la antena en la parte trasera del TV/DVD.
Cable coaxial de
75 ohmios
Jack de
antena
PARA ABONADOS AL SERVICIO CODIFICADO DE TV CABLE
Si usted es abonado a un servicio de TV cable que requiere el uso de un convertidor/caja decodificadora,
conecte el cable coaxial entrante de 75 ohmios al convertidor/caja decodificadora. Utilizando otro cable coaxial
de 75 ohmios conecte el jack de salida del convertidor/caja decodificadora al jack de la antena del TV/DVD.
Vea las conexiones mostradas abajo. Sintonice el TV/DVD al canal de salida del convertidor/caja
decodificadora (generalmente canal 3 ó 4), y utilice el convertidor/caja decodificadora para seleccionar los
canales.
Cable entrante
de 75 ohmios
de Cable TV
Cable de 75
ohmios el TV/DVD
Convertidor/Decodificador
Jack de
antena
PARA ABONADOS AL SERVICIO DE TV CABLE BASICO NO CODIFICADO CON CA-
NALES PREMIADOS CODIFICADOS
Si usted está abonado a un servicio de TV cable en el cual los canales básicos no están codificados y los
canales premiados requieren el uso de un convertidor/caja decodificadora, puede desear utilizar un divisor de
señales y una caja de conmutación A/B (disponible en las compañías de cable o en las tiendas de artículos
electrónicos). Vea las conexiones mostradas abajo. Con el conmutador en la posición “B”, usted puede
sintonizar directamente cualquiera de los canales no codificados en su TV/DVD. Con el conmutador en la
posición “A”, sintonice su TV/DVD a la salida del convertidor/caja decodificadora (generalmente canal 3 ó 4), y
utilice el convertidor/caja decodificadora para sintonizar los canales codificados.
Ca
de
de
Jack de
antena
12
5P20521A [S] (11-16)
12
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Seleccion de idioma en pantalla
Puede escoger entre tres idiomas diferentes (inglés, francés y español) para los despliegues en pantalla.
Para encenber el TV/DVD, presione POWER se encenderá el
indicador Power.
1
Presione TV MENU en el mode de TV.
2
Aparece la pantalla del menú de la TV.
Presione
ó
para
3
A
B C
CH
seleccionar
.
LANGUAGE/IDIOMA/LANGUE
/MENU
Presione
ó
para
4
A
B C
CH
seleccionar el idioma deseada:
inglés (ENGLISH), español
(ESPAÑOL) o francés
LANGUAGE/IDIOMA/LANGUE
(FRANCAIS), luego presione el
botón ENTER.
/
/ ENTER/MENU
Presione TV MENU para volver a
la imagen normal de TV.
NOTAS:
•
Si la unidad no funciona correctamente
(mediante los botones de la unidad y los
del control remoto), desconecte el cable
de alimentación, espere unos minutos y
vuelva a conectarlo. El funcionamiento del
reproductor puede haberse visto afectado
por la electricidad estática u otros
problemas.
La sección de la TV tiene su propio menú al
igual que la sección del DVD (ver página 27).
•
13
5P20521A [S] (11-16)
13
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Operacion del TV
Para encender el TV/DVD,
1 presione el botón POWER.
Ajuste el nivel de volumen
2 presionando el botón + ó – de
VOL. El nivel de volumen será
indicado en la pantalla por medio
de barras verdes y una
indicación de número. A medida
que el volumen aumenta, se
incrementan el número de
barras y la indicación de número.
Si se reduce el volumen, el número
de barras verdes y la indicación
de número decrecen.
VOLUME
32
Ajuste el modo TV/CABLE
3 a la posición apropiada.
TV
- Canales de VHF/UHF
CABLE - Canales de TV CABLE
(Ver página 17.)
Presione el botón de selección
directa de canal.
4
CH 02
Selección directa de canal en
modo de TV Cuando la opción de
menú de TV/CABLE sea ajustada
al modo de TV, todos los canales
podrán ser seleccionados en forma
instantánea usando sólo dos
botones. (Por ejemplo, para
seleccionar el canal 2, presione “0”
y “2”. Si usted sólo presiona “2”, la selección del canal se
retardará unos minutos.) Para los canales de 10 en adelante,
presione los dos digitos en orden.
Selección directa de canal en modo de CABLE
Cuando la opción de menú de TV/CABLE sea ajustada al modo de
CABLE, los canales podrán ser seleccionados de la siguiente
forma:
PARA SELECCIONAR LOS CANALES DE CABLE:
1-9
Presione “0” dos veces, y luego 1-9 según sea necesario.
Por ejemplo, para seleccionar el canal 2, presione “002”.
Primero presione “0”, y luego los 2 dígitos restantes.
Por ejemplo, para seleccionar el canal 12, presione “012”.
Presione los 2 dígitos en orden.
10-12
13-99
Por ejemplo, para seleccionar el canal 36, presione “36”.
100-125 Presione los 3 dígitos en orden.
Por ejemplo, para seleccionar el canal 120, presione “120”.
NOTA REFERENTE A LOS CANALES 1 - 12:
Si usted sólo presiona 1 ó 2 botones, el canal correspondiente
será seleccionado al cabo de 2 segundos.
CABLE
TV
VHF
2-13
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
NOTAS:
• Si se ha seleccionado un canal sin
emisión, el sonido se silenciará
automáticamente.
• Si una estación que estaba viendo
deja de transmitir, el televisor se
desconectará automáticamente
después de 15 minutos.
(5A)
14
5P20521A [S] (11-16)
14
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
CANNAL
/
Presione y libere CH
ó
La
unidad se detendrá
automáticamente en el siguiente
canal almacenado en la memoria.
Antes de seleccionar canales, éstos
deberán ser almacenados en la
memoria del televisor. Consulte la
sección “Para memorizar canales”
en las páginas 17 y 18.
LLAMADA
Presionar DISPLAY/CALL para ver
la información actual en la pantalla.
Presionar DISPLAY/CALL
nuevamente para que desaparezca
esta información.
STEREO SAP
SEL. STEREO
CH 012
•
Número de canal o modo de VIDEO
• Stereo o status de audio SAP
(segundo programa de sonido)
• Status de la salida de audio
VISION RAPIDA
Este botón le permite retroceder
hasta el último canal sintonizado al
presionar QUICK VIEW. Presione
este botón otra vez para regresar al
último canal que estaba mirando.
SILENCIAMIENTO
Presione MUTE botón para silenciar
el sonido. El sonido del TV/DVD
será silenciado y aparecerá
MUTE
brevemente en pantalla la indicación
“MUTE”. El sonido puede ser
devuelto a su nivel original
presionando otra vez este botón o
uno de los botones + ó – de VOL.
DORMIR
SLEEP
120
Para programar el TV/DVD para que
se apague después de cierto tiempo
programado, presione SLEEP del
control remoto. El reloj entrará en
cuenta regresiva, 10 minutos por
cada presión SLEEP (120, 110,
...10, 0). Después que el tiempo de
apagado está programado, aparecerá una indicación brevemente
cada diez minutos para recordarle que la función de apagado
automático está activada. Para confirmar el tiempo del
temporizador de apagado, presione SLEEP y el tiempo restante
aparecerá brevemente.
Para cancelar el temporizador de apagado, presione SLEEP
varias veces hasta que la indicación muestre 0.
15
5P20521A [S] (11-16)
15
5/12/04, 2:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Subtítulo cerrado
¿QUE ES LA RECEPCION DE TEXTO?
Este televisor tiene capacidad para descodificar y mostrar los programas de televisión con emisión de texto.
Esta función mostrará el texto en pantalla para los usuarios con problemas de audición o traducirá y mostrará
el texto que se encuentre en otra lengua.
Leyendas: Este modo de recepción de texto mostrará el texto
en pantalla en inglés u otra lengua (dependiendo de la
programación CH. 1 ó 2 de recepción de texto).
Generalmente las emisiones de textos en inglés son recibidas
en el canal 1 de recepción de texto y los textos en otras
lenguas son recibidos en el canal 2 de recepción de texto.
Las leyendas aparecerán en los lugares de la pantalla que
interfieran mínimamente con la imagen, generalmente en la
parte inferior de la misma. Los programas de noticias
mostrarán generalmente tres líneas de leyendas que
cambiarán en la pantalla. La mayoría de los otros programas
ofrecen dos o tres líneas de leyendas colocadas cerca del
personaje que está hablando de tal manera que el usuario
pueda seguir el diálogo.
Las letras itálicas o subrayadas indican títulos, palabras en
lenguas extranjeras o palabras que requieren énfasis. Las
letras de canciones aparecen encerradas entre notas
musicales.
Texto: El modo de recepción de texto llenará la pantalla con la
programación de programas y otras informaciones.
Después de seleccionar uno de los modos de recepción de
texto, éste continuará activado hasta que se lo cambie,
independientemente de que se sintonice otro canal.
Si se pierde la señal de la emisión de texto debido a un aviso
comercial o al corte de la señal, las leyendas reaparecerán
cuando la señal sea recibida nuevamente.
Si se cambia de canal, las leyendas se retardarán en 10
segundos aproximadamente.
Para recibir emisiones de programas de televisión con emisión
de texto, refiérase a su guía de TV en la que estarán
indicadas con el símbolo (CC).
PARA MIRAR EMISIONES DE
TEXTO
Presione TV/CAP/TEXT para
conmutar entre TV normal y los
dos modos de recepción de
texto (leyendas y texto en toda la
pantalla). Este modo mostrará el
texto en la pantalla para los
usuarios con problemas de
audición.
NOTAS:
Cuando seleccione la recepción de texto, las leyendas aparecerán durante 10 segundos aproximadamente.
Si no se recibe la señal de emisión de texto, no aparecerán leyendas, pero el televisor permanecerá en el
modo de recepción de texto.
•
•
Cuando las leyendas estén en pantalla puede ser que las indicaciones de funciones como volumen y
silenciamiento no aparezcan ya que interferirían con las leyendas.
Ocasionalmente podrán aparecer faltas de ortografía o caracteres extraños durante la recepción de texto.
Esto es normal en este modo, especialmente con los programas en vivo. Esto se debe a que durante los
programas en vivo, los textos son ingresados sin edición, ya que no hay tiempo para la misma.
Algunos sistemas de cable y sistemas de protección contra copias pueden interferir con la señal de emisión
de texto.
Si utiliza una antena interior o si la recepción del TV es muy insuficiente, el texto de las emisiones puede no
aparecer o mostrar caracteres extraños y errores de ortografía. En tal caso, ajuste la antena para mejorar la
recepción o utilice una antena externa.
•
•
•
•
16
5P20521A [S] (11-16)
16
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Para memorizar canales
Este TV/DVD está equipado con una función de memorización de canales que permite avanzar o retroceder al
siguiente canal almacenado en la memoria, pasando por alto los canales no deseados. Antes de seleccionar
canales, éstos deberán ser programados en la memoria del TV/DVD. Además de los canales normales de VHF y
UHF, este TV/DVD puede recibir hasta 113 canales de TV cable. Para usar el TV/DVD con una antena, ajuste la
opción de menú TV/CABLE al modo “CABLE”.
SELECCION DE TV/CABLE
Presione TV MENU en el mode de TV.
1
Aparece la pantalla del menú de la TV.
Presione
ó
para
2
3
4
A
B C
CH
CH
seleccionar
.
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Presione
seleccionar “TV/CABLE”.
ó
para
A
B C
CH
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Presione
ó
para
A
B C
CH
seleccionar “TV” ó “CABLE”. La
flecha indica el modo
seleccionado.
TV/CABLE
TV
AUTO CH MEMORY
ADD/ DELETE
TV
- Canales de VHF/UHF
CABLE - Canales de TV CABLE
/
/
/
/ MENU
Presione TV MENU hasta que se
5 borre la pantalla MENU.
CANALES DE TV CABLE
El cuadro abajo muestra el sistema típico de la localización de los
canales por cable.
Números en este TV
Canal de Cable TV correspondientes
14
A
15
B
16
C
17
D
18
E
19
F
20
G
21
H
22
I
23
J
24
K
25
L
26
M
27
N
28
O
29
P
30
Q
31
R
32
S
33
T
34
U
35
V
36
W
37
38
39
40
AA BB CC DD
41
42
43
44
45
II
46
JJ
47
48
49
50
51
52
53
54
55
56
57
58
EE FF GG HH
KK LL MM
NN OO PP QQ RR SS TT UU VV
59
60
61
62
63
64
65
66
67
68
III
69
70
71
72 73
74
75
76
WW AAA BBB CCC DDD EEE FFF GGG HHH
JJJ KKK LLL MMM NNN OOO PPP QQQ
77
78
79
80
81
82
83
84
85
86
86
87
87
88
88
89
89
90
90
91
91
92
92
93
93
94
94
RRR SSS TTT UUU VVV WWW XXX YYY ZZZ
95
96
97
98
99 100 101 102 103
104 105 106 107 108 109 110 111 112
104 105 106 107 108 109 110 111 112
A-5 A-4 A-3 A-2 A-1 100 101 102 103
113 114 115 116 117 118 119 120 121
113 114 115 116 117 118 119 120 121
122 123 124 125 01
122 123 124 125 5A
17
5P20521A [S] (17-23)
17
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Para memorizar canales
(Continuacion)
SINTONIZACION DE MEMORIA AUTOMATICA DE CANAL
Presione TV MENU en el mode de TV.
1 Aparece la pantalla del menú de la TV.
Presione
ó
para seleccionar
A
2
B C
CH
CH
.
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Presione
ó
para seleccionar
A
3 “AUTO CH MEMORY”, a
B C
CH
continuación presione . El TV
comenzará a memorizar todos los
canales disponibles en su área.
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/ MENU
Presione TV MENU hasta que se
borre la pantalla MENU.
4
PARA ADICIONAR/BORRAR CANALES
Presione TV MENU. Aparece la
1 pantalla del menú de la TV.
CH
Presione
ó
para seleccionar
.
2
3
4
A
B C
CH
TV/CABLE
CABLE
AUTO CH MEMORY
ADD/ DELETE
/
/
/
/ MENU
Presione
“ADD/DELETE”, a continuación
ó
para seleccionar
A
B C
CH
TV/CABLE
CABLE
presione
.
AUTO CH MEMORY
ADD/ DELETE
/
/
/ MENU
Seleccione los canales deseados a
agregar o borrado mediante los
botones de selección directa de
ADD
CH 001
canal (0-9) o CH
Presione
ó
.
ó
para seleccionar
“ADD” (añadir) ó “DELETE” (borrar),
dependiendo de la función que
quiera realizar.
0-9 /
/
/
/
/ MENU
Presione TV MENU hasta que se borre la pantalla MENU.
5
6
Repita los pasos 1 y 5 para ser añadido o borrado cada canal.
18
5P20521A [S] (17-23)
18
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Seleccion Chip-V
Puede establecerse una limitación de edad para impedir que los niños vean o escuchen escenas
violentas o contenidos para adultos, etc. La unidad se corresponde con "TV RATING" y "MOVIE RATING".
Para usar la función V-Chip debe registrar una contraseña.
PARA REGISTRE CONTRASEÑA
Presione TV MENU en el mode de TV.
1 Aparece la pantalla del menú de la TV.
Presionar
ó
para
2
A
B C
CH
seleccionar
, luego presione
ó
para seleccionar
“PASSWORD”.
/
/
/
/ MENU
Entre la contraseña (4 cifras) con
A
B C
3 los botones de selección directa
CH
de canal (0-9) y presione ENTER.
Si entra un número de
contraseña equivocado,
presione CANCEL.
0-9/ENTER/CANCEL/MENU
Aparece “ ” en lugar del número.
Entre nuevamente la misma
A
B C
4 contraseña para la seguridad y
CH
presione ENTER.
V-CHIP SET
Ahora se ha registrado la
contraseña y el menú de
configuración de V-Chip aparecerá
en la pantalla.
NEW
PASSWORD
:
0-9/ENTER/CANCEL/MENU
NOTAS:
Si se olvida de la contraseña, no
podrá ajustar el V-Chip.
•
Para no olvidarse de la contraseña,
anótela y guárdela en un lugar seguro.
•
19
5P20521A [S] (17-23)
19
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Seleccion Chip-V
(Continuacion)
PARA AJUSTAR EL V-CHIP
En el menú V-CHIP SET,
A
1 presione
B C
CH
ó
para
seleccionar “V-CHIP SET”,
a continuación presione
V-CHIP
V-CHIP SET
OFF
.
CHANGE PASSWORD
/
/
/ MENU
Presione
ó
para
seleccionar “TV RATING”, luego
presione para que
aparezca el ajuste deseado.
OFF No se ajusta a TV RATING
2
A
B C
CH
ó
V-CHIP SET
TV RATING
TV-Y7
OFF
MOVIE RATING
:
TV-Y : Todos los niños
TV-Y7 : 7 años ó mayor
/
/
/
/
ENTER/MENU
TV-G : Audiencia general
TV-PG: Con autorización de los padres
TV-14 : 14 años ó mayor
TV-MA: 17 años ó mayor
Cuando seleccione TV- Y7, TV-PG, TV-14 ó TV-MA, presione
DISPLAY/CALL para mostrar el nivel de prohibición. Presione
ó
para seleccionar la clasificación deseada.
Presione
ó
para seleccionar el ajuste “ON” ó “OFF”.
Presione
ó
para
A
B C
3 seleccionar “MOVIE RATING”.
CH
V-CHIP SET
TV RATING
TV-Y7
OFF
Para utilizar el televisor después de
proteger el TV.
MOVIE RATING
Cuando se reciba el programa
aplicado al parámetro del V-Chip,
introduzca la contraseña y presione
ENTER. Cuando se introduce la
contraseña correcta, la protección se
anula temporalmente.
/
/
/
/ ENTER/MENU
Presione
ó
para seleccionar
4
A
B C
CH
prohibición deseada, luego presione
ENTER.
V - CHIP SET
TV RATING
TV
-
-
Y7
13
MOVIE RATING
PG
OFF
:
No se ajusta a MOVIE
RATING
NOTAS:
• La función V-Chip se activa sólo en
los programas y cintas que tienen
señal de prohibición.
• Si está cambiando los canales
utilizando una caja de cable
G
PG
:
:
Para autorización de los padre
Con autorización de padres
/
/
/
/ ENTER/MENU
PG-13 : Con autorización de padres
Menos de 13 años
Menores de 17 años se recomienda
R
:
mientras que el TV/DVD está
sintonizando en el canal 3 ó 4, el
V- Chip funciona de forma diferente.
Cuando entre su contraseña para
cancelar temporalmente el bloqueo
en cualquier canal, se desactivará
enteramente la función del V-Chip
para todas las emisoras. Para
reponer el V-Chip, desconecte el
TV/DVD y vuelva a conectar.
• Algunas cajas de cable fueron
diseñadas con una función de
retardo, en algunos casos puede
demorar unos 10 segundos
Se seguire autorizaciós de los padres
NC-17 : 17 años ó mayor
Sólo para adultos
X
:
Presione
ó
para
A
B C
5 seleccionar “V-CHIP”.
CH
V-CHIP
OFF
V-CHIP SET
CHANGE PASSWORD
/
/
/
/ MENU
Presione
ó
para que
6
A
B C
CH
aparezca “ON”. Sus ajustes
quedan grabados en la
memoria.
V-CHIP
V-CHIP SET
ON
para que un programa aparezca
después de entrar una contraseña.
CHANGE PASSWORD
Presione TV MENU hasta que se
7 borre la pantalla de MENU.
20
/
/
/
/ MENU
5P20521A [S] (17-23)
20
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA CAMBIAR LA CONTRASEÑA
Presione TV MENU en el mode de TV.
1 Aparece la pantalla del menú de la TV.
Presione
ó
para
2
A
B C
CH
seleccionar
.
/
/
/
/ MENU
Presione
seleccionar “PASSWORD”.
ó
para
3
A
B C
CH
0-9/ENTER/CANCEL/MENU
Entre la contraseña con los
botones de selección directa
de canal (0-9) y presione
ENTER.
Si entra un número de
contraseña equivocado,
presione CANCEL.
4
5
6
A
B C
CH
V-CHIP SET
PASSWORD
:
0-9/ENTER/CANCEL/MENU
Presione
ó
para
A
B C
CH
seleccionar “CHANGE
PASSWORD”, a continuación
V-CHIP
V-CHIP SET
ON
presione
.
CHANGE PASSWORD
/
/
/MENU
Entre la contraseña nueva con
los botones de selección
directa de canal (0-9) y
presione ENTER.
A
B C
CH
0-9/ENTER/CANCEL/MENU
Vuelva a escribir la misma
contraseña para confirmarla y
presione ENTER.
7
8
A
B C
CH
Presione repetidamente TV
MENU para volver a la pantalla
normal.
21
5P20521A [S] (17-23)
21
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajustes de control de imagen
Los controles de imagen han sido preajustados en fábrica, pero usted puede reajustarlos individualmente como sigue:
Presione TV MENU en el mode de TV.
Aparece la pantalla del menú de la TV.
1
Presione
ó
para
2
A
B C
CH
seleccionar
.
PICTURE
PICTURE PREFERENCE
/
/
/
/ MENU
Presione
ó
para
A
B C
3 seleccionar “PICTURE”,
CH
a continuación presione
.
PICTURE
PICTURE PREFERENCE
/
/
/ MENU
Presione
ó
repetidamente
4 para seleccionar el punto que
A
B C
CH
BRIGHTNESS
CONTRAST
COLOR
0
+32
0
desea ajustar.
TINT
0
SHARPNESS
0
/
/
/
/ CANCEL / MENU
ó
dos veces para hacer el ajuste.
5 Presione
BRIGHTNESS
(BRILLO)
aumenta el brillo
disminuye el brillo
disminuye el contraste
tiene un color pálido
color rojizo
CONTRAST
(CONTRASTE)
aumenta el contraste
color brillante
COLOR
(COLOR)
TINT
(TINTE)
color hacia el verde
le imagen es más nítida
SHARPNESS
(DEFINICION)
le imagen es más suave
Después de encontrar el ajuste deseado presionar TV MENU
6 hasta que desaparezca la pantalla de MENU.
REPOSICION
Al presionar CANCEL durante los ajustes de imagen hará que los
mismos regresen a los niveles preajustados en fábrica.
NOTA:
La función contraste se prejusta en
fábrica máximo nivel.
22
5P20521A [S] (17-23)
22
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste de la preferencia de imagen
Puede elegir entre los cuatro modos de imagen [ STANDARD (Normal), SPORTS (Deportes), MOVIE
(Película) y MEMORY (Memoria) ] que se describen en la siguiente tabla:
Presione TV MENU en el mode de TV.
Aparece la pantalla del menú de la TV.
1
Presione
.
ó
para seleccionar
2
A
B C
CH
PICTURE
PICTURE PREFERENCE
/
/
/
/ MENU
Presione
“PICTURE PREFERENCE”,
a continuación presione
ó
para seleccionar
3
A
B C
CH
.
PICTURE
PICTURE PREFERENCE
/
/
/ MENU
Presione ▲ ó ▼ para seleccionar
4 el modo de imagen deseado,
A
B C
CH
PICTURE PREFERENCE
STANDARD
SPORTS
a continuación presione ENTER.
MOVIE
MEMORY
/
/ ENTER / MENU
Modo
Calidad de imagen
STANDARD Calidad de imagen normal (ajuste de fábrica)
SPORTS
MOVIE
Imagen brillante y dinámica (ajuste de fábrica)
Ajuste de la imagen tipo película (ajuste de fábrica)
Sus preferencias personales (modo ajustado por
usted; véase “Ajustes de control de imagen” en
la página 22).
MEMORY
Después de encontrar el ajuste deseado presionar TV MENU
5 hasta que desaparezca la pantalla de MENU.
23
5P20521A [S] (17-23)
23
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Segundo programa de sonido (SAP) y estereo
El aparato de TV/DVD está equipado con una función conocida como sonido de TV multicanal o MTS. Las
transmisiones MTS permiten disfrutar mejor de la TV ya que sus programas tienen un sonido en estéreo de alta
fidelidad. MTS también tiene un canal adicional llamado segundo programa de sonido o SAP que los canales de TV
pueden utilizar para transmitir un segundo idioma en las transmisiones bilingües o para otros propósitos.
PARA ESCUCHAR SONIDOS EN ESTEREO
Cuando el aparato de TV está
encendido o se hace una selección
STEREO
CH 013
de canal, asegúrese de que aparece
“STEREO” en la pantalla. Esto
significa que se pueden recibir
transmisiones en “Estéreo”. Puede
disfrutar de los sonidos en estéreo
utilizando las altavoces izquierdo y
derecho.
• Cuando se reciben transmisiones
“Monoaural” no aparece ninguna
indicación.
• Si la señal transmisora no es lo
suficientemente fuerte o no puede
escuchar nítidamente los sonidos
en estéreo, presione AUDIO para
cambiar a un sonido monoaural.
Con este deberán eliminarse los
ruidos. Presione nuevamente para
escuchar los sonidos en estéreo.
PARA ESCUCHAR EN SAP (SEGUNDO PROGRAMA DE SONIDO)
Cuando el aparato de TV está
encendido o se hace una
selección de canal, asegúrese
STEREO SAP
CH 013
de que aparece SAP en la
pantalla. Esto significa que se
puede recibir transmisiones en
“Segundo programa de sonido”.
PARA SELECCIONAR SONIDO DESEADO
Presione el botón AUDIO para
seleccionar el sonido deseado.
SEL. STEREO
TRANSMISION ESTEREO+SAP
SONIDO ESTEREO
(PRINCIPAL)
SONIDO SEPARADO
SONIDO MONOAURAL
(PRINCIPAL )
24
5P20521A [S] (24-28)
24
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Disco
Este aparato sólo funciona con discos DVD de la región 1 ó región ALL.
El disco cargado (DVD-Video y CD de audio) se reconocerá automáticamente.
Los formatos de disco apropiados son: DVD-Video, CD de audio, CD-R/RW y DVD-R/RW (solo formato vídeo
DVD).
Algunos discos CD-R/RW pueden ser incompatibles.
No reproduzca un DVD-ROM, DVD-Audio, CDV, CD-G, Video CD o Foto CD para evitar el borrado accidental
del material pregrabado.
Esta unidad no toca archivos MP3/WMA/JPEG.
Título
DISCO DVD
Cuando hay dos o más películas grabados en un
disco, el disco se divide en dos o más secciones.
Cada sección se denomina un “TITULO”.
TITULO1
CAPITULO 1
TITULO2
CAPITULO 2 CAPITULO 1
CAPITULO 2
CAPITULO 3
Capítulo
Los títulos pueden subdividirse en muchas secciones.
Cada sección se denomina un “CAPITULO”.
Canción
CD de audio
Un disco compacto de audio puede contener varios
elementos.
Estos se asignan a las canciones.
CANCION
1
CANCION
2
CANCION
3
CANCION
4
CANCION
5
Para sacar el disco de su caja
Sujete firmemente por el borde del disco. No toque la superficie del disco.
Saque suavemente el disco de la caja.
• No raye el disco.
• No ensucie la superficie del disco.
• No pegue una etiqueta o cinta adhesiva en el disco.
• No deje caer o doble el disco.
Para guardar el disco
• Guarde el disco en su caja para evitar el riesgo de ralladuras, polvo o daños.
• No deje el disco expuesto a los rayos del sol o en lugares calientes o húmedos.
Para limpiar el disco
Frote el disco con un paño limpio, seco, desde el centro a los bordes.
• No frote el disco con un movimiento circular.
• No utilice limpiadores líquidos o en aerosol.
25
5P20521A [S] (24-28)
25
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparación / Estado del disco
En las siguientes páginas se describe
la instalación y la operación en modo
DVD.
Preparación
Antes de poner en funcionamiento el DVD/CD, efectúe las
siguientes preparaciones.
Introduzca el cable de CA en una toma de corriente
1
estándar de CA polarizada de 120 V y 60 Hz.
• Si el cable de CA se enchufa por vez primera, espere
unos 5 segundos antes de presionar POWER.
NOTA: Al conectar a otros equipos, desenchufe la unidad
de la toma de CA.
Presione POWER en la unidad o en el mando a distancia
para encender la unidad. Se encenderá el indicador
POWER.
2
• Cada vez que presiona POWER, el TV/DVD se
enciende desde el modo TV.
• Cuando use un amplificador, enciéndalo.
Presione TV/DVD para
3
No Disc
seleccionar el modo DVD.
Aparecerá la pantalla de inicio
del DVD.
Pantalla de estado del disco
Presione DISPLAY/CALL dos veces. Aparecerá la pantalla de
estado del disco.
Número del capítulo
DVD
Tiempo transcurrido de reproducción
Número del título
del título
Funcionamiento
del disco
Idioma del sonido
Tiempo total del título
Ángulo de la cámara
Un tipo de sonido
00:34:56 01:12:33
1/99 Chapter 1/999
1/9
1/8 Eng Dolby Digital
1/32 Eng
Title
Idioma de los
subtítulos
Para que desaparezca la pantalla de estado, presione
DISPLAY/CALL de nuevo.
CD de AUDIO
Tiempo transcurrido de reproducción de la pista
Funcionamiento del disco
Número de la pista
34:56
71:33
Tiempo total de la
pista
Track 11/99
NOTA:
Si la unidad no funciona
correctamente:
La electricidad estática, etc., puede
afectar al funcionamiento del
reproductor. Desconecte el cable de CA
y vuelva a conectarlo.
• Cuando reproduzca el disco CD, aparecerá la pantalla de
estado.
26
5P20521A [S] (24-28)
26
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección del idioma
Puede cambiar los parámetros
predeterminados para personalizar el
funcionamiento como prefiera.
Presione TV/DVD para
No Disc
1
2
3
seleccionar el modo DVD.
“No Disc” aparecerá en
pantalla. (Si el disco DVD
ya fue introducido,
empezará a correrlo
inmediatamente.)
Language Picture Sound Parental Other
Presione SETUP en el
modo de parada. El MENÚ
DE AJUSTE de DVD
aparecerá en pantalla.
Presione
para
seleccionar “Other”.
/Enter/Setup/Return
Language Picture Sound Parental Other
OSD Language English
Presione
o ENTER para
seleccionar “OSD Language”.
/Enter/Setup/Return
Language Picture Sound Parental Other
Presione
presione
seleccionar el idioma
deseado (porejemplo
inglés) y presione ENTER.
o ENTER y
para
4
5
OSD Language English
English
Francais
Espanol
o
/Enter/Setup/Return
Presione SETUP o RETURN para eliminar la pantalla
Menú.
NOTAS:
• Si el idioma seleccionado para la banda
sonora no está grabado en el disco, se
reproduce el idioma original.
• Si el idioma seleccionado para los
subtítulos no está grabado en el disco,
se selecciona el idioma prioritario.
27
5P20521A [S] (24-28)
27
5/12/04, 2:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedimiento de reproducción
Presione TV/DVD para
seleccionar el modo
DVD.
1
Presione OPEN/CLOSE
en el aparato o en el
mando a distancia.
Se abrirá la bandeja del
disco.
Coloque un disco en la
bandeja. Sujete el disco,
colóquelo con el lado de
etiqueta impresa hacia
arriba, alinee en las guía
y coloque el disco en su
posición correcta.
2
3
Presione OPEN/CLOSE
o PLAY. La bandeja del
disco se cierra
automáticamente.
En la pantalla del TV la
indicación “ ” cambia a
“Reading” y empieza la
reproducción.
• Aparece la pantalla del
menú en la pantalla de
TV, si el disco tiene una
función de menú.
Reading
NOTAS:
En este caso, presione
• Si se coloca un disco no compatible,
aparecerá “Incorrect Disc”, “Region Code
Error” o “Parental Error” en la pantalla de
TV dependiendo del tipo de disco cargado.
En este caso, revisar el disco nuevamente
(Ver páginas 25 y 38).
• Algunos discos pueden demorar un minuto
antes de empezar la reproducción.
• Puede aparecer un símbolo
“Prohibido” en la parte superior izquierda
de la pantalla. El símbolo indica que la
función seleccionada no está disponible en
el disco o que el aparato no puede acceder
a esa función en ese momento. No indica
un problema con el aparato.
• Cuando coloque un disco de una sola cara
con esa etiquetq abajo (i.e. del lado
incorrecto) y presione PLAY o OPEN/
CLOSE en el aparato, aparecerá “Read-
ing” en la pantalla y después aparecerá
continuamente la palabra “Incorrect Disc”.
• AlgunasfuncionesdereproduccióndeDVD
puedenhabersidoelegidasporelproductor
de la película. Como este aparato repro-
duce los DVD de acuerdo con las
posibilidadesintroducidasporelproductor,
algunasfuncionesdereproducciónpueden
no existir. Consulte además las
instrucciones que vienen con el DVD.
,
,
,
ó ENTER
para activar una función
de menú.
Presione STOP para terminar la reproducción.
• El aparato graba el punto de parada, según el disco.
Aparece“ ” en la pantalla durante 4 segundos
aproximadamente. Presione PLAY para continuar
reproduciendo (desde el mismo punto).
• Si presiona nuevamente STOP o se retira el disco
(Aparece “ ” en la pantalla), el aparato borrará el punto
de parada.
4
5
de
A continuación presione OPEN/CLOSE.
Se abre la bandeja del disco.
Saque el disco y presione POWER.
La bandeja del disco se cierra automáticamente y se
desconecta el aparato.
28
5P20521A [S] (24-28)
28
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproducción especial
NOTA: Puede ocurrir una leve demora
entre el momento en que presiona el
botón y que se active la función.
Reproducción con avance rápido
Presione SEARCH durante la reproducción normal.
Cada vez que presione el botón de SEARCH
, aumentará
(x4), (x8),
la velocidad de la búsqueda
(x15).
(x2),
(CD:
(x 2),
(x 4),
(x 8),
(x 20))
• Para seguir con la reproducción normal, presione PLAY.
Reproducción con retroceso rápido
Presione SEARCH
durante la reproducción normal.
Cada vez que presione el botón de SEARCH
, aumentará
(x4), (x8),
la velocidad de la búsqueda
(x15).
(x2),
(CD:
(x 2),
(x 4),
(x 8),
(x 20))
• Para seguir con la reproducción normal, presione PLAY.
Reproducción Fija
Presione PAUSE/STILL
durante la reproducción
normal para hacer una pausa
en la reproducción.
Para seguir con la
reproducción normal,
presione PLAY.
Avance cuadro por cuadro
Presione PAUSE/STILL durante la imagen fija.
Avanza un cuadro cuando presione PAUSE/STILL una vez.
Para seguir con la reproducción normal, presione PLAY.
Reproducción de cámara lenta
Presione SLOW ( ) en retroseso o SLOW ( ) durante la
reproducción normal o imagen fija.
Cada vez que presione SLOW, cambiará la velocidad del
slow x1/2, x1/4, x1/6, x1/7.
• Para seguir con la reproducción normal, presione PLAY.
• Para volver a la imagen fija, presione PAUSE/STILL.
NOTA:
El aparato puede mantener una imagen
fija de video o la imagen visualizada en
la pantalla, en su pantalla de TV,
permanentemente. Si deja la imagen
fija de video o la imagen visualizada en
la pantalla en su TV durante mucho
tiempo, puede dañar permanentemente
la pantalla de TV. Los televisores de
proyección tienen tendencia a sufrir
este problema.
Búsqueda de un capítulo o canción
Presione SKIP (7) en avance o SKIP (6) en retroceso
durante la reproducción para buscar un capítulo que desea
ver. Cada vez que presione el botón, se salta un capítulo o
canción.
29
5P20521A [S] (29-30)
29
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Zoom / Búsqueda de la escena deseada
Zooming (acercamiento)
Estaunidadlepermitiráhaceracercamientosdelaimagen
del marco y podrá efectuar selecciones cambiando la
posición del marco.
Presione ZOOM durante
la reproducción.
La parte central de la
imagen se agranda.
Cada vez que presione el
ZOOM cambiará el ZOOM
1
1
1 (x1,3),
3 (x2,0).
2 (x1,5) y
Presioneelbotón
del marco. Puede mover el marco del centro hacia UP
(arriba),DOWN(abajo),LEFT(izquierda),RIGHT(derecha).
/
/
/
paraverunapartediferente
2
3
En el modo ZOOM presione ZOOM varias veces para
regresar a una visión 1:1 (
Off).
Búsqueda de la escena deseada
Utilice el título, capítulo y tiempo grabados en el disco
para buscar el punto que desea reproducir.
Presione JUMP durante
la reproducción.
1
Jump
Time
Title
Chapter
/Enter/0 9/Cancel/Jump
2 Presione
ó
para seleccionar el “Time”, “Title” or
“Chapter”.
Presione las selección directa de canal (0-9) para
cambiar el número.
3
• Si entra un número equivocado, presione CANCEL.
• Consulte la caja en la que viene el disco para
confirmar los números.
Presione ENTER.
4
NOTAS:
• Puede seleccionar la reproducción con
pausa, cámara lenta o búsqueda en el
modo zoom.
• Puede que algunos discos no
respondan a la función de Zoom.
• Empieza la reproducción.
• Cuando cambie el título, empieza a reproducir desde el
capítulo 1 del título seleccionado.
• Este procedimiento puede no funcionar en algunos
discos.
30
5P20521A [S] (29-30)
30
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reproducción repetida
Reproducción de título, capítulo, canción
Presione PLAY MODE durante el modo de reproducción o el
parada.
1
DVD
CD
Repeat
/Enter/Play Mode
:
Off
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Presione
“Chapter” ó “Title”.
Si se trata de un CD, presione
/
ó ENTER una ó dos veces para seleccionar
2
primero para seleccionar
“Repeat”, luego presione
/
ó ENTER una o dos veces
para seleccionar “Track” ó “All”.
DVD
CD
Repeat
/Enter/Play Mode
:
Chapter
Play Mode
Repeat
:
:
Off
All
/Enter/Play Mode
Presione PLAY MODE nuevamente para que desaparezca la
pantalla.
• Presione PLAY para iniciar la reproducción repetida.
• Para volver a reproducción normal, seleccionar Repeat Off.
3
Reproducción repetida A-B
La reproducción repetida A-B le permite repetir el material entre
los dos puntos seleccionados.
Presione REPEAT A-B
durante la reproducción.
Se selecciona el punto inicial.
1
A
Presione nuevamente
2
A
B
REPEAT A-B. Se selecciona
el punto final. Empieza a
reproducir en el punto
seleccionado.
NOTAS:
• La función de repetición puede no
funcionar en algunos discos.
• En el modo de repetición A-B pueden
no aparecer los subtítulos cerca del
punto A o B.
La reproducción se detiene en
el punto final, vuelve al punto
A y vuelve a empezar
nuevamente.
• Durante la reproducción repetida la
característica ANGLE no operará.
• Puede no ser posible programar la
repetición A-B en algunas escenas
del DVD.
Para continuar con la reproducción normal, presione
nuevamente REPEAT A-B. Aparece “
” en la pantalla.
Off
31
5P20521A [S] (31-36)
31
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Programacion de reproduccion/Reproducción aleatoria
(disco compacto)
Programación de reproducción
Se puede cambiar el orden de las canciones en el disco.
Presione PLAY MODE en el
modo de parada.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Presione
ó
para
Play Mode
Repeat
:
:
Program
Off
7
8
9
2 seleccionar “Play Mode”, luego
1
4
10
11
12
presione
seleccionar “Program”.
/
ó
ENTER para
2
3
5
6
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
Ejemplo: Si desea programar
en orden 7, 3, 11: Entre como 7
3
4
Play Mode
Repeat
:
:
Program
Off
7
8
9
, 3
, 11.
1
2
3
7
3
11
4
5
6
10
11
12
Si pone un número equivocado,
pulse CANCEL.
Clear
Program Playback
/Enter/0 9/Cancel/Play Mode
Presione
/
ó
/
para
Program Playback
Track 7/11
02:31 08:29
seleccionar “Program Playback”
y presione ENTER. “Program
Playback” aparecerá en
pantalla. Los programas que
seleccionó se empezarán a
reproducir en orden.
Para volver a la reproducción
normal, seleccione “Play Mode:
Off” en el paso 2 anterior.
Reproducción aleatoria
Presione PLAY MODE durante
el modo de reproducción o el
parada.
1
Play Mode
Repeat
:
:
Off
Off
/Enter/Play Mode
Presione
ó
para
seleccionar “Play Mode”, luego
presione ó ENTER para
NOTAS:
2
3
Play Mode
Repeat
:
:
Random
Off
• Para cancelar el programa de play,
seleccione “Clear (salir)” en el paso
4 y presione ENTER.
• El programa se cancela cuando abra
la bandeja del disco o cuando se
desconecta el aparato.
• La reproducción aleatoria no puede
combinarse con la reproducción
repetida.
/
/Enter/Play Mode
seleccionar “Random”.
Presione PLAY.
“RandomPlay”apareceráenpantallayseiniciarálareproducción
aleatoria.
Para volver a la reproducción normal, seleccione “Play Mode:
Off” en el paso 2 anterior.
32
5P20521A [S] (31-36)
32
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Marcación de escenas deseadas
El aparato memoriza los puntos que
desea ver nuevamente.
Puedecontinuarlareproduccióndesde
Marcación de escenas
Presione MARKER
1
Marker
Marker
Marker
1
2
3
dicha escena.
durante la reproducción.
/Enter/Cancel/Marker
Seleccionar el Marker en
blanco utilizando el botón de
2
Marker
Marker
Marker
1
2
3
00 27 54
/
, después presione el
/Enter/Cancel/Marker
botón de ENTER en la
escena deseada.
• Se pueden seleccionar
hasta 3 escenas.
• Repita este procedimiento
para ajustar las otras 2
escenas.
Presione el botón MARKER para que desaparezca este
despliegue.
3
Para volver a las escenas
PresioneMARKERdurante
1
Marker
Marker
Marker
1
2
3
00 27 54
01 16 25
02 08 31
la reproducción o el modo
stop.
/Enter/Cancel/Marker
Presione el botón
para seleccionar el Marker
1-3.
ó
Marker
Marker
Marker
1
2
3
00 27 54
01 16 25
02 08 31
2
3
/Enter/Cancel/Marker
Presione ENTER.
La reproducción empieza desde la escena marcada.
Para cancelar la marca
Presione MARKER.
1
Presione el botón
ó
para seleccionar el Marker 1-3.
2
3
Presione CANCEL.
Presione MARKER para eliminar este visualizador.
NOTAS:
• La marcación se cancela cuando abra
la bandeja del disco o desconecta el
aparato.
• Algunos subtítulos grabados cerca del
marcador puede no aparecer. [DVD]
33
5P20521A [S] (31-36)
33
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cambio del idioma de la pista de sonido / Subtítulos
Cambio del idioma de la pista de sonido
Se puede seleccionar el idioma cuando reproduce un
disco en múltiples idiomas.
Presione AUDIO durante
la reproducción.
1
1/8 Eng Dolby Digital
Apareceráelidiomaactual
de la pista de sonido.
Presione AUDIO hasta
que quede seleccionado
el idioma deseado.
2
2/8 Fra Dolby Digital
El despliegue en pantalla
desaparecerá después de
unos cuantos segundos.
Subtítulos
Aparición y desaparición de subtítulos
Cuando reproduzca un disco con subtítulos grabados,
puede hacer que éstos aparezcan o desaparezcan.
Presione SUBTITLE durante
la reproducción hasta que
aparezca "Off".
Off
Cambio del idioma de los subtítulos
NOTAS:
Puede seleccionar el idioma para reproducir un disco
grabado con subtítulos en múltiples idiomas.
• Si no se escucha el idioma deseado
después de presionar AUDIO varias
veces, el idioma no fue grabado en el
disco.
• El cambio del idioma en la pista de
sonido se cancela cuando abra la
bandeja del disco o desconecte el
aparato apague el aparato. El idioma
por omisión inicial o idioma existente
volverá a escucharse cuando vuelva a
reproducir el disco.
Presione SUBTITLE
durante la reproducción
hasta que aparezca el
idioma deseado.
1
1/32 Eng
• El cambio del idioma de los subtítulos
se cancela cuando abre la bandeja del
disco.
El despliegue en pantalla desaparecerá después de unos
cuantos segundos.
2
• Puede que algunas funciones no
funcionen en algunos DVD. Quizá no
pueda activar o desactivar los subtítulos
ni cambiarlos. Al reproducir el DVD, el
subtítulo puede cambiar cuando:
- abre o cierra la bandeja del disco
- cambia el título.
• En algunos caso, el idioma de los
subtítulos no cambia inmediatamente
al seleccionado.
34
5P20521A [S] (31-36)
34
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cambio de ángulos/ Selección de título/ Menú DVD
Cambio de ángulos
Cuando reproduce un disco grabado en múltiples
ángulos, puede cambiar el ángulo de visión de la
escena.
Presione ANGLE durante
la reproducción.
1
1/9
Aparecerá el angle actual.
Presione ANGLE varias veces hasta que seleccione el
angle deseado.
2
Selección de título
Hay dos o más títulos grabados en algunos discos. Si
se ha grabado el menú de título en el disco, puede
seleccionar el título deseado.
Presione TOP MENU durante la reproducción.
Aparece el menú de título en la pantalla.
1
Presione
2 deseado.
/
ó
/
para seleccionar el título
Presione ENTER o PLAY.
Empieza la reproducción del título seleccionado.
3
Menú DVD
Algunos DVD permiten seleccionar el contenido del
disco con el menú.
Cuando reproduce este tipo de DVD, puede seleccionar
el idioma de los subtítulos, idioma de la pista de sonido,
etc. con el menú DVD.
Presione DVD MENU durante la reproducción.
Aparece el menú DVD en la pantalla.
1
• Presione nuevamente DVD MENU para volver a
reproducir la escena en la que se estaba
reproduciendo cuando presionó DVD MENU.
NOTAS:
Presione
/
ó
/
para seleccionar el ítem deseado.
2
3
• En algunos DVD, puede no ser posible
cambiar los ángulos incluso cuando se
grabó en múltiples ángulos en el DVD.
• En algunos DVD puede nos ser posible
seleccionar el título. En algunos DVD el
“menú de título” puede tener el nombre
de “menú” o de “título” en las
Presione ENTER.
El menú continúa en otra pantalla. Repita los pasos 2 y
3 para terminar de seleccionar el ítem completamente.
instrucciones que vienen con el disco.
35
5P20521A [S] (31-36)
35
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste del formato (relación de aspecto) de la pantalla de
la TV / Ajuste de la visualización en pantalla
Ajuste del formato (relación de aspecto) de
la pantalla de la TV
Puede seleccionar el formato de su TV.
Presione SETUP en el modo de
parada o No Disc.
Language Picture Sound Parental Other
1
2
3
Presione
ó
para
seleccionar “Picture”.
/Enter/Setup/Return
Presione
ó ENTER, a
Language Picture Sound Parental Other
continuación Presione
ó
Tv Screen
Display
4:3
On
para seleccionar “Tv Screen”.
/Enter/Setup/Return
Presione
ó
ó ENTER. Presione
para seleccionar el tipo
Language Picture Sound Parental Other
Tv Screen
Display
4:3
On
4:3
4:3
de pantalla deseada, luego
presione ENTER.
/Enter/Setup/Return
Puede elegir entre los siguientes tamaños de pantalla:
4:3 Letterbox
Al reproducir un disco DVD para pantalla ancha, presenta
la imagen ocupando toda la anchura del TV, con bandas
negras en la parte superior e inferior de la imagen.
4:3
Panscan
Presenta la imagen ocupando toda la pantalla, y recortando
automáticamente los extremos izquierdo y derecho.
Presione SETUP ó RETURN para eliminar la pantalla
Menú.
4
Ajuste de la visualización en pantalla
Aparecen o desaparecen las indicaciones en la
pantalla cuando presione DISPLAY.
Presione SETUP en el modo de parada o No Disc.
1
Presione
ó
para seleccionar “Picture”.
Language Picture Sound Parental Other
Presione
continuación Presione
para seleccionar “Display”.
ó ENTER, a
2
3
ó
Tv Screen
Display
4:3
On
Presione
seleccionar “On” ó “Off”.
ó ENTER para
Language Picture Sound Parental Other
Tv Screen
Display
4:3
Off
NOTA:
ON: Aparecen las indicaciones en la pantalla cuando
presione los botones (ajuste de fábrica).
OFF: No aparecen las indicaciones en la pantalla cuando
presione los botones salvo SET UP, SEARCH MODE,
PLAY MODE, MARKER y DISPLAY.
El disco DVD no siempre puede mostrar
la imagen con su ajuste preferido de
imagen; por ejemplo, si selecciona “4:3
Panscan”, puede que el disco no ofrezca
esta opción. En este caso la imagen se
mostraría en el formato que sea capaz
de reproducir el disco.
Presione SETUP ó RETURN para eliminar la pantalla Menú.
4
36
5P20521A [S] (31-36)
36
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Control de Gama Dinámica
El DRC (Control de Gama Dinámica)
le permite controlar la gama
dinámica para lograr un sonido
conveniente para su equipo.
Presione TV/DVD para
1
Language Picture Sound Parental Other
seleccionar mode de TV.
Presione SETUP en el
modo de parada.
Presione
ó
para
seleccionar “Sound”.
/Enter/Setup/Return
Presione ó ENTERpara
seleccionar “DRC”.
2
3
4
Language Picture Sound Parental Other
DRC
On
/Enter/Setup/Return
Presione
Presione
ó ENTER.
para
Language Picture Sound Parental Other
ó
On
Off
DRC
On
seleccionar “On” ó “Off”.
/Enter/Setup/Return
Presione SETUP ó RETURN para retirar la pentalla de
Menu.
NOTAS:
• DRC funciona sólo con la reproducción de
grabaciones Dolby Digital.
• El nivel de DRC puede variar según el disco
de vídeo DVD.
37
5P20521A [S] (37-40)
37
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajuste de restricciones para menores
Algunos discos no son apropiados
para los niños. Estos discos pueden
limitarse para no reproducirse con la
unidad.
Presione SETUP en el
modo de parada.
1
Presione
ó
para
seleccionar “Parental” y
presione
Presione
ó ENTER.
ó
para
2
seleccionar “Parental”
a continuación presione
ó
hasta que
aparezca el nivel que
requiera.
• Nivel no: No funciona el ajuste de restricciones para
menores.
• Nivel 8: Se puede reproducir todo el DVD.
• Nivel 1: El DVD para mayores no puede reproducirse.
• Seleccione entre el nivel 1 al nivel 8. La limitación será
más severa conforme el número sea más bajo.
Presione
ó
para
3
seleccionar “Password”,
Presione selección
directa de canal (0-9)
para introducir una
contraseña de 4 dígitos.
¡Asegúrese de recordar
este número!
• Si introduce un número
incorrecto, presione
CANCEL.
Presione ENTER para
guardar la contraseña.
NOTA: Ahora la
4
5
clasificación está
NOTAS:
bloqueada y el ajuste no
puede cambiarse a menos
que introduzca la
• Una vez completado cada ajuste
(P.27, 36~39, 41~43), el aparato
puede seguir funcionando en las
mismas condiciones
(especialmente con discos DVD).
Cada ajuste puede mantenerse en
la memoria aunque desconecte el
aparato.
• Para algunos discos, el aparto no
puede prohibir la reproducción.
• Algunos discos no puede codificarse
con determinada información de nivel
de prohibición aunque la etiqueta del
disco diga “adulto”. Para estos discos
no funcionará la prohibición para
menores.
contraseña correcta.
Presionar SETUP ó ENTER para retirar la pantalla de
restricciones para menores.
38
5P20521A [S] (37-40)
38
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cambio del nivel de restricciones para menores
Presione SETUP en el
modo de parada o no hay
disco.
1
Presione
seleccionar Parental y
presione ó ENTER.
ó
para
Presionar los botones de
los números (0-9) para
introducir la contraseña
que haya almacenado.
2
• Si introduce un número
incorrecto, presione
CANCEL.
Presione ENTER.
La clasificación ahora está
desbloqueada.
3
4
Presione
ó
para
seleccionar “Parental”,
y a continuación presione
ó
para cambiar el
nivel de restricción de
menores.
Presione
ó
para
5
seleccionar “Password” y
presione los botones de
los números (0-9) para
introducir la contraseña.
NOTA: Puede cambiar la
contraseña si así lo desea.
Presione ENTER.
Ahora el nivel de la restricción
queda cambiado y fijo.
6
7
NOTA:
No se olvide de la contraseña. Si olvida la
contraseña, hable con la tienda donde
compró este aparato.
Presionar SETUP ó RETURN para retirar la pantalla de
restricciones para menores.
39
5P20521A [S] (37-40)
39
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Deshabilitación temporal del nivel de rating (clasificación)
del disco DVD
Dependiendo del disco DVD, el disco
Introduzca el disco DVD y
presionePLAYoOPEN/CLOSE
en la unidad (ver pág. 28).
puede tratar de cancelar temporalmente
el nivel de rating que haya ajustado.
Depende de usted si decide cancelar
el nivel de la rating o no.
1
Si el disco DVD fue diseñado para cancelar temporalmente el
nivel del Rating, cambiará la pantalla que aparece después del
“Reading” (lectura) dependiendo del disco que se esté tocando.
Si selecciona “YES” con el botón ENTER aparecerá la pantalla
de “Your disc exceeds the parental control level 1.” (p.ej.).
2
Reading
Your disc exceeds
the parental control level 1.
Parental Control Level
Cancel Picture
/Enter/Return
Si desea cancelar el nivel de clasificación ajustado
temporalmente, seleccione “Parental Control Level” con el
3
botón
ó
y después presione ENTER. Si se estableció
la contraseña de 4 dígitos del paso 3 de la pag. 38, aparecerá
la pantalla de entrar contraseña como aparece en el paso 4.
Alternativamente, si no se ha establecido ninguna contraseña,
comenzará la reproducción. Si desconoce (u olvidó) la
contraseña, seleccione “Cancel Picture”.
La pantalla de ajuste desaparecerá. Presione OPEN/CLOSE
para sacar el disco.
Entre la contraseña con los
botones de número (0-9).
Después, presione ENTER.
4
5
Please enter the
digit password
4
Si interrumpe la introduccion
de la contraseña, presione
RETURN.
Enter/0 9/Cancel/Return
La reproducción comenzará si se introdujo la contraseña
correcta.
NOTA:
Esta cancelación temporal del nivel del
rating se mantendrá hasta que se saque
el disco. Cuando se extraiga el disco se
establecerá el nivel de rating original de
manera automática.
40
5P20521A [S] (37-40)
40
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección del idioma del menú
Se puede seleccionar el idioma de los
mensajes del menú de disco de los
DVD.
Presione SETUP en el modo de
parada o no hay disco.
Language Picture Sound Parental Other
1
2
3
Presione
ó
paraseleccinar
“Language”.
/Enter/Setup/Return
Presione ó ENTERypresione
paraseleccionar“Menu”.
Language Picture Sound Parental Other
ó
Menu
Subtitle
Audio
English
Automatic
English
/Enter/Setup/Return
Presione
Presione
ó ENTER.
para
ó
seleccionar su idioma deseado
y presione ENTER.
English, Français, Espanol:
Se verá u oirá el idioma seleccionado.
Other:
Se puede seleccionar otro idioma.
(Consulte la “Lista de códigos de idiomas” en la página 44).
Presione SETUP ó RETURN para retirar la pentalla de Menu.
4
41
5P20521A [S] (41-47)
41
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección del idioma de los subtítulos
Se puede seleccionar siempre el
mismo idioma de subtítulos aunque
cambie de disco o desconecte el
aparato.
Presione SETUP en el modo de
parada o no hay disco.
Language Picture Sound Parental Other
1
2
3
Presione
ó
para
seleccionar “Language”.
/Enter/Setup/Return
Presione
presione
ó ENTER y
para
ó
seleccionar “Subtitle”.
Presione
Presione
ó ENTER.
para
ó
seleccionar su idioma
deseado y presione ENTER.
English, Francais, Espanol:
Aparece el subtítulo con el idioma seleccionado si está
registrado en el disco.
Other:
Si desea seleccionar otro idioma, entre el código de
idioma (consulte la “Lista de códigos de idiomas” en la
página 44).
Automatic:
• El aparato seleccionará automáticamente el mismo idioma
seleccionado para el AUDIO.
• Cuando el aparato selecciona el mismo idioma que para el
AUDIO los subtítulos no aparecen durante la reproducción.
• Cuando no utilice el mismo idioma que el AUDIO, los
subtítulos aparecerán durante la reproducción.
Off:
No aparecen subtítulos.
Presione SETUP ó RETURN para retirar la pentalla de Menu.
4
NOTA:
Si el idioma seleccionado no se grabó
en el disco, se selecciona el idioma de
máxima prioridad.
42
5P20521A [S] (41-47)
42
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Selección del idioma de la pista de sonido de audio
Se puede seleccionar el mismo
idioma de la pista de sonido de
audio incluso aunque cambie de
disco o desconecte el aparato.
Presione SETUP en el modo de
parada o no hay disco.
Language Picture Sound Parental Other
1
Presione
ó
para seleccionar
“Language”.
/Enter/Setup/Return
Presione
ó ENTER y presione
2
3
ó
para seleccionar “Audio”.
Presione
Presione
seleccionar el Idioma de
Audio deseado y después
presione ENTER.
ó ENTER.
ó
para
English, Francais, Espanol:
Se escuchará el idioma deseado si está registrado en el
disco.
Other:
Si desea seleccionar otro idioma, entre el código del
idioma. (Consulte la “Lista de códigos de indiomas” en la
página 44.)
Original:
El aparato seleccionar el idioma de máxima prioridad en
cada disco.
Presione SETUP ó RETURN para retirar la pentalla de Menu.
4
NOTA:
Si el idioma seleccionado no está grabado
eneldisco, seescucharáelidiomaoriginal.
43
5P20521A [S] (41-47)
43
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Lista de códigos de idiomas
Entre el número de código apropiado para los ajustes iniciales “AUDIO”, “SUBTITLE” y/o “MENU LAN-
GUAGE” (consulte las páginas 41~43).
Nombre de idioma Código Nombre de idioma Código Nombre de idioma Código Nombre de idioma Código
Abkhazian
Afar
1112 Fiji
1620 Lingala
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
2224 Singhalese 2919
1111 Finnish
1116 French
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2921
2922
2925
1529
Afrikaans
Albanian
Amharic
Arabic
2111 Malayalam
1415 Maltese
1522 Maori
2322 Sundanese 2931
Armenian
Assamese
Aymara
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
2122 Marathi
1724 Moldavian
1731 Mongolian
1811 Nauru
Azerbaijani
Bashkir
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla 1224 Hebrew
1933 Nepali
2415 Telugu
2425 Thai
Bhutani
Bihari
1436 Hindi
1819 Norwegian
1831 Oriya
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
2629 Tonga
1611 Turkish
2622 Turkmen
2630 Twi
Breton
1929 Panjabi
1924 Pashto, Pushto
1911 Persian
1711 Polish
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
2123 Italian
1930 Portuguese
2011 Quechua
1311 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
2731 Ukrainian
2033 Rhaeto-Romance 2823 Urdu
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
2825 Uzbek
2831 Vietnamese 3219
2923 Volapük
2911 Welsh
1714 Wolof
2928 Xhosa
2918 Yiddish
2924 Yoruba
2914 Zulu
3225
1335
3325
3418
2019
3525
3631
Danish
Dutch
English
Esperanto
Estonian
Faroese
2225 Serbo-Croatian
2211 Shona
1625 Latvian, Lettish 2232 Sindhi
44
5P20521A [S] (41-47)
44
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones de toma Audio/Video
La instalación exacta a utilizar para hacer las conexiones de los distintos componentes de video y audio en el
TV depende del modelo y funciones de cada componente. Confirme en el manual de instrucciones de cada
componente para la posición de las entradas y salidas de video y de audio.
Cómo utilizar un Amplificador AV con sonido digital integrado
Si está utilizando un Amplificador con surround digital integrado, puede disfrutar de los distintos sistemas de
audio, incluyendo el audio con Dolby Surround que hasta ahora sólo se podía disfrutar en los cines.
A continuación se muestra cómo conectar un amplificador AV con decodificador Digital Dolby
integrado, decodificador DTS, decodificador MPEG, etc.
Altavoz
delantero
(derecho)
Altavoz de
subgraves
Atrás del TV/DVD
TV/DVD
UHF/
VHF
Altavoz
delantero
(izquierdo)
Salida de audio
digital coaxial
Cable digital
coaxial (no
suministrado)
Altavoz central
A la entrada de
audio digital coaxial
Altavoz
ambiental
(derecho)
Altavoz ambiental
(izquierdo)
Amplificador AV con decodificador de
surround digital integrado como aparece
arriba enlistado.
Fabricado bajo licencia de Dolby Laboratories. “Dolby” y el símbolo de la doble D son marcas registradas por
Dobly Laboratories.
"DTS" y "DTS Digital Out" son marcas registradas de Digital Theater Systems, Inc.
*
*
NOTAS:
Cuando hace la conexión anterior, en el amplificador AV, no ajuste DOLBY DIGITAL a DOLBY DIGITAL ni
MPEG a MPEG “ON”. Si lo hace, los altavoces emitirán un sonido muy alto que podría causarle daños de
audición o averiar los propios altavoces.
•
Algunos decodificadores DTS que no soportan la interfase DVD-DTS tal vez no funcionen adecuadamente con
la unidad.
•
45
5P20521A [S] (41-47)
45
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones de toma Audio/Video
(Continuacion)
Cómo utilizar las entradas de audio/video
Si conecta el TV/DVD a la videograbadora, cámara de video o juego de video, puede seleccionar presionando
INPUT SELECT.
Presione repetidamente el botón INPUT SELECT para seleccionar el modo deseado.
Aparecerá "LINE" o TV en la pantalla durante 4 segundos.
LINE
NOTA:
Esta botón no funcionará en el
modo DVD.
1. Para conectar el TV/DVD a una videograbadora
Presionar INPUT SELECT para seleccionar el modo deseado para utilizar la TV como monitor.
Operar la videograbadora como siempre.
VCR
Frente del TV/DVD
A entrada de Video
A entrada de Audio (der.)
A salida de Audio/Video
A entrada de Audio (izq.)
Cordon de Audio/Video (no está incluido)
2. Para conectar el TV a la videocámara
Para reproducir de la videocámara, conecte la videocámara en el TV tal como se indica.
Videocámara
Frente del TV/DVD
A entrada de Video
A salida de Audio/Video
A entrada de Audio (der.)
A entrada de Audio (izq.)
Cordon de Audio/Video (no está incluido)
3. Para conectar el TV/DVD a un juego de TV.
El TV/DVD puede utilizarse también como pantalla para muchos juegos de video. Sin embargo, debido a que
existe una gran variedad de tipos diferentes de señales generadas por estos aparatos y diferentes requisitos
de conexión correspondientes, no se han incluido todas las posibilidades posibles en los diagramas de
conexión sugeridos. Para más detalles, deberá consultar el manual de instrucciones de cada componente.
Frente del TV/DVD
A entrada de Video
A salida de Audio/Video
A entrada de Audio (der.)
A entrada de Audio (izq.)
Cordon de Audio/Video (no está incluido)
46
5P20521A [S] (41-47)
46
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Disturbios de recepcion
La mayoría de los tipos de interferencia de televisión pueden ser solucionados ajustando la altura y la
posición de la antena de VHF/UHF. Para obtener los mejores resultados se recomiendan las antenas
exteriores. Los tipos más comunes de interferencia de televisión están mostrados abajo. Si aparece
uno de estos síntomas cuando el TV/DVD está conectado a un sistema de TV cable, el disturbio puede
ser causado por la compañía local emisora de TV cable.
IGNICION
Aparecen manchas negras o bandas horizontales y la imagen puede
ondular o ser inestable. Es generalmente causado por interferencia
proveniente de los sistemas de encendido de los automóviles,
lámparas de neón o máquinas herramientas de CA y artículos
electrodomésticos tales como taladros y secadores de cabello.
FANTASMAS
Los fantasmas son causados por una señal de televisión que fluye por
dos vías. Una es la vía directa y la otra es la reflejada por los edificios
altos, colinas u otros objetos grandes. El cambiar la dirección o
posición de la antena puede mejorar la recepción.
NIEVE
Si el TV/DVD está ubicado lejos de la estación de TV, en un área de
recepción limitada donde la señal es débil, pueden aparecer pequeños
puntos en la imagen. Si la señal es extremadamente débil, puede ser
necesario instalar una antena externa más grande.
INTERFERENCIA DE RADIO FRECUENCIA (RFI)
Causada por radios de dos vías, este tipo de interferencia produce
ondulaciones que se mueven o líneas diagonales en la imagen.
En algunos casos puede causar pérdida de contraste de la misma.
El cambiar la dirección y la posición de la antena, o la instalación de un
filtro de RFI puede mejorar la imagen.
VARIACION DEL TAMAÑO DE LA IMAGEN
Una pequeña variación del tamaño de la imagen es normal cuando
usted ajusta los controles de CONTRASTE o BRILLO.
CUIDADOS Y MANTENCION
Para evitar incendios o peligros de choques eléctricos, desconecte el TV/DVD de la fuente de CA antes de la
limpieza. La terminación del gabinete puede ser limpiada con un paño suave y un jabón suave y como otros
muebles. Tome precauciones cuando limpia o pasa un paño en las partes de plástico.
47
5P20521A [S] (41-47)
47
5/12/04, 3:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problemas y localización de averías
Utilice la siguiente lista de verificación de localización de averías cuando tiene problemas con este aparato.
Consulte con su concesionario local o tienda de servicio si continúan los problemas.
Compruebe que se han hecho correctamente todas las conexiones cuando utilice con otros aparatos.
SINTOMA
POSIBLE SOLUCION
Página
ENERGIA
•Verifique que el cable de alimentación está conectado.
•Pruebe con otra toma de corriente de CA.
10
14
El TV/DVD no funciona.
•
•
La alimentaicón está desconectada; revise el fusible o el cortacircuitos.
Desconecte la unidad y luego vuelva a conectarla.
RECEPCION DE PROGRAMAS DE TV
•La estación o el servicio de TV cable están con problemas;
sintonice otra estación.
•Verifique los ajustes de volumen.
•Determine si hay posibles fuentes de interferencia.
Sonido de baja calidad o
ausencia de sonido.
14
47
•La estación o el servicio de TV cable están con problemas;
sintonice otra estación.
•Revise las conexiones de la antena o sistema TV cable;
14
11,12
Imagen de baja calidad o
ausencia de imagen.
reoriente la antena.
•Determine si hay posibles fuentes de interferencia.
•Verifique los ajustes de los controles de imagen.
47
22
•La estación o el servicio de TV cable están con problemas;
sintonice otra estación.
•La señal de la estación es débil; reoriente la antena.
14
Mala recepción en algunos
canales.
11,12
47
•Determine si hay posibles fuentes de interferencia.
•La estación o el servicio de TV cable están con problemas;
sintonice otra estación.
14
•Verifique que haya canales almacenados en la memoria.
•Verifique los ajustes de los controles de imagen.
•Revise las conexiones de la antena o sistema TV cable;
reoriente la antena.
18
22
11,12
Mala definición de los colores o
ausencia de color.
•Determine si hay posibles fuentes de interferencia.
•La estación o el servicio de TV cable están con problemas;
sintonice otra estación.
47
14
La imagen presenta oscilación o
desplazamiento.
18
–
11
12
17
14
•Verifique que haya canales almacenados en la memoria.
•El servicio TV cable está transmitiendo una señal codificada.
•Reoriente la antena.
•Revise todas las conexiones del sistema TV cable.
•Ajuste la opción de menú de TV/CABLE al modo CABLE.
•La estación o el servicio de TV cable están con problemas;
pruebe con otra estación.
La recepción TV cable no es
posible.
Aparecen barras horizontales o
verticales en la pantalla.
•Revise las conexiones de la antena y reoriente la antena.
•Determine si hay posibles fuentes de interferencia.
11,12
47
•Asegúrese de que la opción de menú TV/CABLE está ajustado a
la posición apropiada en la selección de menú de la pantalla.
17
La recepción no es posible más
allá del canal 13.
•
Si está usando una antena, revise las conexiones de la antena de UHF. 11
•La estación sintonizada no está transmitiendo.
•El temporizador de desactivación automática ha sido activado.
•El suministro de energía se ha interrumpido.
14
15
–
El televisor se apaga.
•Estación de TV está experimentando problemas o programa
sintonizado no es en modo de subtítulo cerrado. Pruebe en otro canal.
•Asegúrese de conexión de CABLE o antena VHF/UHF,
reposición o gire antena.
14
11,12
16
La función de subtítulo cerrado
no es activada.
•
Precione el botón de TV/CAP/TEXT para encender la codificador
de subtítulo cerrado.
La lengua deseada no se muestra. •Seleccione la lengua apropiada en las selecciones de menú.
13
48
5P20521A [S] (48-BACK)
48
5/12/04, 3:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SINTOMA
POSIBLE SOLUCION
Página
DVD
• No hay disco colocado.
• El disco puede estar sucio. Limpie el disco.
• El aparato no puede reproducir CD-ROM, etc.
28
25
–
No empieza la reproducción.
No hay imagen.
• El selector TV/DVD no está ajustado correctamente.
26
–
• Compruebe que el selector de entrada del amplificador está en
la posición correcta.
• El aparato está en un modo de reproducción especial.
No hay sonido.
29
45
•
Seleccionar la posición correcta de la Salida de Audio en el amplificador AV.
La imagen se ve distorsionada
durante la localización progresiva
o regresiva.
• La imagen puede quedar distorsionada a veces.
–
No puede parar la reproducción,
búsqueda, cámara lenta,
reproducción repetida o
• Algunos discos pueden no aceptar algunas funciones.
• El ajuste no corresponde al de su TV.
–
reproducción programada, etc.
No se ve la imagen en 4:3.
36
36
45
No hay indicaciones en la pantalla. • Seleccione Display On.
Noseescuchaelsonidoambiental. • El ajuste no corresponde al de su sistema estéreo.
Una tecla del aparato o mando a
distancia no lo hace funcionar.
• Desconecte el aparato y desenchufe el cable eléctrico de CA
durante varios minutos. Vuelva a enchufar.
–
No empieza la reproducción al
seleccionar el título.
• Verifique el ajuste del nivel de prohibición.
38~40
El idioma de la pista de sonido de
audio y/o subtítulos no cambia al
reproducir un DVD.
• No se han grabado múltiples idiomas en el disco DVD.
41
• Algunos discos no tienen subtítulos.
• Los subtítulos se han eliminado. Presione SUBTITLE.
No se ven los subtítulos.
34
No cambia el ángulo.
Aparece “ ” en la pantalla.
CONTROL REMOTO
• No se ha grabado desde múltiples ángulos en el disco DVD.
• La función está prohibida para este aparato o disco.
35
28
• Apunte el mando a distancia hacia el sensor remoto.
• Utilice a una distancia de menos de 5 metros o baje la luz en la
habitación.
• Elimine los obstáculos para el rayo infrarrojo.
• Las pilas están gastadas. Cambie las pilas.
• Compruebe que las pilas están bien colocadas.
No funciona el mando a distancia.
10
SISTEMA DE DESMAGNETIZACIÓN
Esta televisión tiene un circuito de desmagnetización que eliminará todas las distorsiones de
color de la pantalla del televisor causadas por un exceso de magnetismo que se acerque
demasiado al televisor. Este circuito está diseñado para funcionar una vez cuando se enchufe la
unidad por primera vez. Si se ven pequeñas distorsiones de color en algunos puntos de la
pantalla, desenchufe el televisor durante 15 minutos aproximadamente. Cuando se vuelva a
enchufar el televisor, el circuito de desmagnetización funcionará una vez par eliminar cualquier
distorsión de color. Repita este procedimiento en cualquier momento en que el televisor sea
magnetizado accidentalmente o bien se mueva o se cambie de lugar.
49
5P20521A [S] (48-BACK)
49
5/12/04, 3:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Especificaciones
GENERALIDADES
Fuente de alimentación:
Consumo de energía:
120V CA, 60 Hz
Operation: 75 Vatios
Stand by: 5 Vatios
24,3 libras (11 kg)
Peso:
Dimensiones:
Anchura
Altura
Profundidad
:
:
:
14-1/4 pulgadas (362 mm)
15-1/16 pulgadas (382 mm)
14-3/8 pulgadas (365 mm)
Temperatura de operación:
Humedad de funcionamiento:
5° - 40°C
Menos de 80%
TELEVISOR
Tubo de imagen:
Tipo de sintonizador:
Canales de recepción:
13” (335mm diagonalmente)
Cuarzo PLL frecuencia sintetizada
VHF
2-13
UHF
14-69
TV CABLE
14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
Entrada de antena:
Altavoz:
Potencia de salida de audio:
Cable coaxial de entrada de VHF/UHF 75 ohmios
1,5” (38mm) x 2,7” (69mm), 8 ohmios x 2
1,5 W + 1,5 W
Tocadiscos de DVD/Discos
compactos
Señal de Sistema:
Disco utilizable:
NTSC
1. DVD (12cm, 8cm)
2. CD (12cm, 8cm)
Por debajo del Nivel Medible
Video :
Audio :
Variaciones de velocidad:
Entradas:
(RCA) 1 Vp-p/75 ohmios
(RCA) –8 dBm/50K ohmios
Salida de audio digital:
Captor:
0,5Vp-p 75ohmios terminados
CD :
Longitud de onda: 770 - 800 nm
Potencia máxima de salida: 0,7 mW
Longitud de onda: 645 - 660 nm
Potencia máxima de salida: 0,5 mW
DVD :
Accesorios:
Control Remoto
Antene telescópia
50
5P20521A [S] (48-BACK)
50
5/12/04, 3:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
5P20521A [S] (48-BACK)
51
5/12/04, 3:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For repair
-
in your home
-
of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
Au Canada pour service en français:
a domicilio, y para ordenar piezas:
1-800-LE-FOYERMC
1-888-SU-HOGARSM
(1-800-533-6937)
(1-888-784-6427)
www.sears.ca
® Registered Trademark / TM Trademark / SM Service Mark of Sears, Roebuck and Co.
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears, Roebuck and Co.
MC Marque de commerce / MD Marque déposée de Sears, Roebuck and Co.
© Sears, Roebuck and Co.
Printed in Thailand
Impreso en Tailandia
04/06
U
5P20521A [S] (48-BACK)
52
5/12/04, 3:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Kyocera Printer FS 3700 User Manual
Lennox International Inc Furnace G71MPP User Manual
Lenovo Laptop E431 User Manual
LG Electronics Washer F1056LDP User Manual
Life Fitness Bicycle LCSU30 0XXX 01 User Manual
Logitech Computer Keyboard MK360 User Manual
Mantis Trimmer E System User Manual
Melissa Scale 631 033 User Manual
Micro Innovations Network Card USB740R User Manual
Micron Technology Laptop Transport LT User Manual