GENUINE REMOTE ENGINE START
USER’S INSTRUCTIONS
Parts number：C930 V7 620
Thank you for purchasing a genuine Mazda accessory.
Before use, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly use the Remote Engine Start.
Your safety depends on it.
After using this instruction manual, store it in a place where it can be easily located.
Note, consult your authorized Mazda dealer, or a dealer appointed store, for proper
vehicle installation of the Remote Engine Start.
If the vehicle equipped with this product, or the product itself, is sold, transferred or
loaned to another party, be sure to give this instruction manual to the new owner, so he
or she can use this product safely and correctly.
<Safe and correct use of the product>
Various warnings and cautions are displayed in this manual to assist you in the safe and
correct use of the product and as precautions against you or others being injured, or the
product being damaged.
Depending on the degree of possible injury or damage that may be incurred,
precautionary items have been divided into ‘Warnings’ and ‘Cautions’ and illustrated with
symbols to depict the nature of the precautionary content.
A WARNING indicates a situation in which serious
injury or death could result if the warning is ignored.
WARNING
A CAUTION indicates a situation in which bodily injury
or damage to objects, or both, could result if the
caution is ignored.
CAUTION
GB
Always follow the ADVICE noted to ensure vehicle
safety and performance. Vehicle damage could result,
or proper performance may be compromised if the
ADVICE
advice is ignored.
A NOTE indicates information or a point related to
vehicle usage. Vehicle damage could result, or proper
performance may be compromised if the note is
ignored.
NOTE
No.:ZZ092-00640-00
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Remote Engine Start features
zThe Remote Engine Start allows the user to start the engine of a vehicle
from a remote location using a remote control.
zThe user can turn on the air conditioner / heater beforehand so the cabin
of the vehicle can be cooled or heated ahead of time.
zThe user can check the status of the vehicle from a remote location.
2. Safety precautions
WARNING
Do not install this device on a vehicle equipped with a
manual transmission.
● Only install this device on designated vehicles which
the harness fits.
● This device can only be installed on vehicles
equipped with AT / CVT. Do not install this product on
a vehicle equipped with a manual transmission
because it is hazardous.
Do not start the engine while inside an enclosed space or
garage.
● Never start up the engine while inside an enclosed
space where the exhaust fumes can build up, such
as a poorly ventilated garage, an underground
parking garage or a parking tower. The exhaust
fumes are hazardous and can cause poisoning or
intoxication.
Ensure that the periphery of the vehicle is safe.
● Use this device only where you can thoroughly check
that the periphery of the vehicle is safe. In particular,
using the device while a child or pet is close by can
result in an unexpected accident.
Do not disassemble or modify this device.
● Never disassemble or modify this device, or install it
in a location not specified in this manual. Otherwise,
it may not operate correctly and/or may result in an
accident or breakdown. In addition, this situation is
not covered under warranty.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Do not start up the engine using the Remote Engine Start
when parked on an incline.
● If the vehicle were to move unintentionally due to the
engine vibration, jolt, etc., it could result in a serious
accident.
Performing safe maintenance and inspection.
● When performing vehicle inspection and
maintenance, remove the (-) terminal on the vehicle
battery. Never start up the engine with the remote
control during inspection or maintenance at a gas or
service station, etc. Otherwise, an accident may
occur, such as getting a hand or clothes caught in
the rotating parts. Do not perform inspection or
maintenance in the engine compartment while the
hood switch is pressed.
Keep the remote control in a safe and secure place.
● Keep the remote control out of the reach of children.
Otherwise, they may swallow the lithium battery
accidentally and choke.
Do not operate this device while other people are inside
the vehicle.
● In order to prevent an unexpected jump start, etc.,
never start the engine while a pet or someone
(especially children) is inside the vehicle. Stopping
the engine automatically using the Remote Engine
Start settings is hazardous (while someone is inside)
because the temperature inside the vehicle may
become too hot. In addition, there is also a risk of
children accidently pressing the climate control
switch and setting the temperature too high or too
low.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Fire prevention.
● Do not start the engine when the vehicle is near
something flammable (oil or dry grass). Otherwise,
the high temperature from the exhaust fumes or
exhaust pipe could cause a fire.
● Do not start the engine while the vehicle is wrapped
with a body cover. Otherwise, the high temperature
from the exhaust fumes or exhaust pipe could cause
a fire.
Do not pour water on the remote control.
● The remote control is water resistant for exposure
during daily life, but it may break down if submerged
in water or if water gets inside the device.
Do not perform standard inspection and maintenance right
after warming up the engine.
● Performing inspection or maintenance before
operation and immediately after warming up your
vehicle could result in a burn injury. First, wait 5
minutes once the engine has stopped. Then, after
checking all the parts for heat hazards, proceed with
the inspection and maintenance.
Check points when the vehicle is parked.
● Perform the following safety checks thoroughly when
the vehicle is parked to prevent potential accidents
when starting the engine.
• Engage the parking brake.
• Put the shift lever in the “P” position.
• Be sure there is no advanced or smart key inside the
vehicle.
• Close all doors and windows.
• Lock the doors.
• Check that the hood is closed.
• Turn off the windshield wipers.
• If the vehicle is equipped with automatic lights, turn off
the automatic light settings.
• Be sure that the steering lock is engaged.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. General information
-Laws in some communities may restrict the use of remote starters. For
example, some laws may require a person using the remote start to have
the vehicle in view when doing so. Check local regulations for any
requirements on remote starting of vehicles.
-This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
-This device complies with industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following tow conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of this device.
-Consult your authorized Mazda dealer for installation of the remote control
engine starter system.
CAUTION
-FCC WARNING
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operating precautions
Usage Environment
●The remote control signal (or the response signal from the controller) may not
reach the controller (or the remote control) if there are strong radio waves
transmitting nearby, or if there are obstacles blocking the signal.
● The engine may be slow to start during severe cold weather conditions.
Vehicles with Remote Control Door Lock Function
●Door Lock and Door Unlock Function by the remote control keyless entry or
advanced keyless entry system equipped the vehicle can be performed while the
engine is running by the Remote Engine Start.
However, if Door Lock and Door Unlock Function do not work due to interference
caused by engine noise, etc., perform these Door Lock and Door Unlock
operations on the vehicle remote control, etc. after stop the engine.
Vehicles with Automatic Lights
● When vehicles equipped with automatic lights are set to the “AUTO”
position for the light switch, the lights turn on if the engine is started at night
with the remote control. However, if the engine automatically stops after
warming up, the lights will also turn off at the same time to prevent the
battery from draining. However, to avoid light interference, set the
automatic light switch to the “OFF” position when using the remote control
to turn on the engine at night.
Do Not Perform Unnecessary Idling
● To help protect the environment, conserve energy and avoid inconveniencing
others, do not perform idling when it is unnecessary or longer than necessary.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Handling Instructions
The remote control is a sensitive electronic device similar to a cellular telephone.
Please follow the handling instructions below to avoid damage to or breakdown of
the remote control.
● Avoid storing or using the remote control in places that expose it to direct
sunlight, places that have high humidity, places with extremely high
temperatures (on top of the dashboard, etc.) or places with extremely low
temperatures (leaving inside the vehicle while parked at ski resorts, etc.).
● Do not store or use the remote control in places where it comes into direct
contact with water.
● Avoid exposure to strong impacts such as dropping it on the floor or hitting it
against something hard.
● If the remote control gets very dirty, use a cloth soaked in a watered-down, mild
or neutral detergent, ring out the liquid solution and wipe down the remote
control. (Never use benzene, thinner or chemically treated cloth/wipes.)
● Avoid attaching a lot of keys to the key ring on the remote control, or sitting
down while the remote control is in your pocket, as it can cause the remote
control to deform and may result in damage.
● While carrying the remote control, if the keys, etc., come into contact with a
vehicle, it can lead to remote control breakdown or malfunction due an
electrostatic discharge. Therefore, be careful of this risk during time periods
when electrostatic discharges occur frequently.
● Be sure that the battery cover and clasp are securely locked. Otherwise, if water
accidently gets inside the internal part of the transmitter, it can cause
breakdown.
● Do not use in restricted areas such as on board airplanes or inside hospitals.
● The remote control can negatively impact electronic and medical devices.
● Be sure to follow the instructions and rules posted inside medical clinics or
facilities regarding the use of electronic devices.
● If the remote control is used on board airplanes, where usage is restricted, you
may be subject to punishment due to airline rules and regulations.
ADVICE
• Depending on the surroundings and how the remote control is held, the minimum
distance required for the signal transmission varies. Generally, if the remote control is
directed toward the vehicle when transmitting the signal, it should successfully transmit
from far away.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Part names
Remote Control
CAUTION
・
・
・
Keep the remote control out of the reach of children. Otherwise, they may swallow the
lithium battery accidentally and choke.
Do not drop the remote control or hit it against something hard. Otherwise, it can result in
breakdown or malfunction.
Do not pour water on the remote control or submerge it. It can result in breakdown or
malfunction.
Front
Side
Back
Side
Car find
switch
Function
switch
Start switch
FCC/IC
Label*
Registration
switch
Stop switch
Key ring
Battery
cover
*<Confirm method of FCC/IC Label>
The FCC/IC label appears when the
Battery Cover is removed.
Controller
Antenna
Sends and receives signal
transmission to and from
the remote control.
Back
FCC/IC Label
Note
• The location for the controller installation varies depending on the vehicle model.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Display
Display
Name
Antenna mark
Description
Turns on when sending or
receiving a signal.
Send mark
Flashes when sending a
transmission signal.
Receive mark
Flashes when receiving a signal.
Send error mark
Turns on when a signal for the
same frequency band is being
used.
Battery mark
Time display
Turns on when the battery life is
low.
Displays the engine warm up
time.
Car find display
Error display
Turns on when conducting the car
find operation.
An error description will display
when an error occurs.
⇒p.16
Engine mark
RUN mark
Turns on when the engine starts
up and is running.
Turns on when the engine starts
up and is running.
STOP mark
Turns on when the engine stops.
Rear defrost mark Turns on when the rear defrost is
running.
Vehicle mark
Turns on when performing a
sending operation.
Hood mark
Turns on when performing a
sending operation. When the
hood is open, it does not turn on.
Turns on when performing a
sending operation. When all
doors are closed, it turns on.
If any door is open, it turns on.
Door close mark
Door open mark
*For further details on the display description, refer to the appropriate
section in the manual.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Basic functions for Remote Engine Start
Engine Start & Stop Function
The remote control is equipped with
engine start, engine stop and
automatic stop (set with timer)
functions. In addition, the engine
start operation will perform when
conditions outlined on page 14 are
Engine start → p.15
satisfied. The air conditioner /
heater can be turned on beforehand
so the cabin of the vehicle can be
cooled or heated ahead of time.
Engine stop → p.18
Rear Defrost Function
The rear defrost turns on in the
following situations.
• When the cabin temperature is 5ºC
(41ºF) or less, 7 seconds after the
engine start operation performed on
the Remote Engine Start.
• When the rear defrost operation is
performed on the remote control.
Directions for rear defrost operation
on remote control → p.23
ADVICE
・The internal temperature of the vehicle cabin varies slightly depending on the
installed location of the controller.
・The rear defrost will automatically stop when the engine stops.
・The rear defrost will automatically stop after 15 minutes of operation on some
vehicle models.
・When the cabin temperature falls to 5ºC (41ºF) or less after 7 seconds from the
engine start, the rear defrost will not turn on automatically.
・The rear defrost cannot be turned off using the remote control.
・On some vehicle models, dash light does not turn on when the rear defrost is
turned on with the Remote Engine Start.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Car Find Function
If the car find operation is
performed on the remote control,
the hazard lights will flash twice and
the horn will sound twice so you
can confirm the vehicle’s location.
This function is convenient when
looking for your vehicle in a large
parking lot, etc.
Car find
Directions for car find
operation → p. 25
Answer Back Function
This device conducts bidirectional
communication between the remote
control and the controller (vehicle
side). The user can check the status
of the operations: engine start,
engine stop, warm up time, and rear
defrost, using the LCD monitor on
Answer back
Vehicle side
(Controller)
Send
Remote control
the remote control.
Note
1. The reference operating range of the remote control is approx. 300 ft(91m).
However, this range can be reduced by interference caused by any of
conditions as follows.
•
•
There is any obstruction nearby (Buildings, walls, other vehicles, etc.).
There is any radio wave transmission nearby (television, radio, cellular,
another remote controller, etc.)
•
The battery becomes weak.
2. When there is a signal being transmitted that is close to the frequency band
used by this device in the surrounding area, transmission between the remote
control and controller shall be restricted. In this situation, the remote control will
display a send error and/or a receive error.
3. When conducting consecutive operations with the remote control switches, wait
“2 seconds or longer” after the “Send mark” on the LCD monitor has turned off,
and then perform the next operation. The operation signal will not be received if
the second operation is performed within 2 seconds of the first.
4. If a send error is displayed, the radio transmission in the area is restricted. Wait
until the display mark turns off before operating the remote control.
5. A receive error may display on the remote control even if the engine has
started, depending on the radio transmission conditions in the area.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Low battery warning & replacement directions
When the battery is running out and
the user tries to conduct an operation,
the “Low battery warning” on the LCD
monitor will display. In this situation,
be sure to replace both batteries at
the same time with new ones. The
performance will go down particularly
under cold conditions.
Battery type: Lithium battery CR2032 / Qty. 2
・ Release the clasps and slide off
Battery cover
the battery cover to remove.
Clasps
ADVICE
If the cover is stuck and does not slide
off, wrap a flathead screwdriver in a
cloth, etc., and use it in the depression to
release the cover and slide it off.
・ Replace with the new batteries so
the plus (+) side is facing up.
Lithium battery
・ Re-attach the battery cover.
(CR2032)
ADVICE
When replacing the batteries, be sure to
replace both batteries at the same time.
WARNING
Keep the batteries out of the reach of
children. In the event that a battery is
accidently swallowed, consult with a
physician right away.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Basic operations
CAUTION
Check points when the vehicle is parked.
When using the engine start function with this device, follow the instructions below
when parking, in order to avoid vehicle theft or an accident from occurring.
・Be sure to always engage the parking brake.
・Put the shift lever in the “P” position.
・Be sure there is no advanced or smart key inside the vehicle.
・Close all doors and windows.
・Lock the doors.
・Close the hood.
・Turn off the windshield wipers.
Engine Start Conditions
When using the Remote Engine Start, be sure to always check the start
conditions listed below beforehand. Even if just one of the conditions has not
been satisfied, the device will interpret this as a hazard and will not operate.
Even if the user tries to operate the remote control, the engine will not start.
The shift lever is
in the “P” position.
There is no advanced key (or
smart key) inside the vehicle.
The ignition switch
is not set to ACC
or ON, etc.
The hood is
closed all the way.
The burglar alarm is not
tripped.
All doors are closed
all the way.
The accelerator and
foot brake are not
engaged.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9-1. Engine start operation
z Press the function switch once.
The LCD display will appear as
shown on the right.
ADVICE
The LCD display will appear when the
Function switch
switch is released.
z Press the start switch while the
above LCD display is shown until
it beeps.
After the send mark flashes, the send
operation is completed. After the send
operation is completed, the controller
will send an answer back signal.
*Press the start switch within 2 seconds
after the LCD display appears. If the
start switch is not pressed in time and
the LCD display disappears, start the
procedure over again from step 1.
Start switch
When the remote control receives a
response from the vehicle, it indicates
the engine start operation with a
display (on the right) and a melody.
After 8 – 15 sec.
Engine start
standby
Engine start
initiated
ADVICE
・ After the engine start operation is initiated, the controller will automatically send
an answer back signal 2 – 3 times.
・ If there is a transmission error, there will not be an answer back signal after the
second time.
・ If the engine start conditions are not satisfied,
⇒p.14
the engine start operation cannot be performed.
・ For vehicles equipped with an automatic wiper function, when the engine start
operation is activated with the remote control, the wipers will not turn on even
when the wiper switch is set to the “AUTO” position and it begins to rain.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD Display During Engine Start Operation
The LCD display will change as shown below depending on the status of
the vehicle, the signal transmission and the switch operation.
Condition Error Display
(Safety detection display description)
If the safety detection function is turns on,
initiated by the vehicle status, the following
display will appear on the LCD monitor. Be
sure to check the vehicle status once more.
Error Display
Display
Description
Troubleshoot
Vehicle transmission error
Remote Engine Start
registration error
Remote Engine Start
authentication error
Vehicle side error
If this display description appears even after
performing the engine start operation again,
consult with an authorized Mazda dealer
where you purchased the device.
ACC or IG is already ON.
Engine rotation error
Engine does not start
Turn off ACC or IG.
Be sure that the accelerator is not engaged.
The battery or gas level may be low. Check
the battery voltage or the fuel gauge.
Close the hood all the way.
Hood is open.
Push start switch is
pressed.
Check whether the push start switch is
pressed.
There is an advanced key
(or smart key) inside the
vehicle.
Be sure there is no advanced or smart key
inside the vehicle.
A door is open.
Close all doors (including the rear gate) all
the way.
Burglar alarm has been
tripped.
Check whether the burglar alarm has been
tripped.
Shift lever is not in the “P”
position.
Put the shift lever in the “P” position.
Foot brake is engaged.
Be sure that the foot brake is not engaged.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
When the start switch is
not pressed while the
LCD display is shown.
Press the function
switch once.
Press the start switch
while the LCD display
is shown until it
beeps.
Timeout
Send
Send
error
Engine
start
standby
Condition
error
Receive
error
Condition
error
Engine
start
Engine
start
Receive
error
initiated
standby
Condition
error
Engine
start
Receive
error
Engine
start
standby
initiated
17
Download from Www.Somanuals.com. All Manuals Search And Download.
9-2. Engine stop operation
This operation only applies when the engine has been started with the
remote control.
z Press the stop switch until it
beeps.
The LCD display will appear as
shown on the right. After the send
mark flashes, the send operation is
completed. After the send operation
is completed, the controller will send
an answer back signal.
Stop switch
When the remote control receives a
response from the vehicle, it
indicates the engine stop operation
with a display (on the right) and a
melody.
Engine stop
Receive
error
Send error
Note
・ On some vehicle models, the engine also stops when the shift lever is pressed.
・ The controller buzzer will sound if the engine is stopped for reasons other than a
normal engine stop or the pre-set engine warm-up time has elapsed.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
● Other Engine Stop Conditions
The engine will stop if one of the following conditions is true.
1) The hood is opened.
2) The shift lever is put in a position other than the “P” position.
3) A door is opened.
4) The push start switch is pressed.
5) The pre-set warm up time has elapsed.
6) The brake pedal is engaged.
7) The accelerator pedal is engaged (the engine stops by the rpm restriction).
8) There is an advanced key or smart key inside the vehicle.
To run the vehicle…
z If the vehicle engine is started with the remote control, stop the engine
with the remote control or opening the vehicle's door.
z Restart the engine with the push start switch.
Note
If the engine is started with the push start switch, it cannot be stopped with the
remote control.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
9-3. Warm up time check
This operation only applies when the engine has been started with the remote
control.
z Press the function switch once.
The LCD display will appear as
shown on the right.
Function switch
ADVICE
The LCD display will appear when the
switch is released.
z Press the start switch while the
above LCD display is shown until it
beeps.
After the send mark flashes, the
send operation is completed. After
the send operation is completed,
the controller will send an answer
back signal.
Start switch
*Press the start switch within 2 seconds after the LCD display appears. If the
start switch is not pressed in time and the LCD display disappears, start the
procedure over again from step 1.
【Display Example】
When the remote control receives a
response from the vehicle, it indicates
・8 min. warm up time remaining
the engine start operation with the
・Engine running
display below and a melody.
・Rear defrost stopped
・ Warm up time remaining?
(It only displays even numbers.)
・ Is the engine running?
・ Is the rear defrost turned on?
20
Download from Www.Somanuals.com. All Manuals Search And Download.
9-4. Vehicle status check
This operation can be performed before or after the engine start operation.
1) Press the function switch until it
beeps.
The LCD display will appear as shown
on the right.
Function switch
After the send mark flashes, the send
operation is completed. After the send
operation is completed, the controller
will send an answer back signal.
When the remote control receives a
response from the vehicle, it indicates
the engine start operation with a
display (on the right) and a melody.
Displays
when engine
stops
Displays
when engine
starts
The following 2 items can be checked.
・ Is the engine running?
・ Is the rear defrost turned on?
Displays when
rear defrost is
turned on
【Display Example】
Note
Some vehicle models stop the rear
defrost after 15 minutes.
Condition error display (p.16) does not
appear.
Engine running
Engine stopped
Rear defrost is turned on.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
9-5. Warm up time settings
<ex.>
When the setting of warm-up time is
changed to “30 min” from “10 min”.
The default setting is 10 minutes.
z Press the function switch and the
start switch at the same time until it
beeps.
Function switch
Start switch
The current setting time is displayed.
z Press the start switch to set the
warm up time.
The setting time “min” will display.
Start switch
z Press the function switch until it
beeps.
Note
Function switch
Some vehicle models stop the rear
defrost after 15 minutes, even if the
warm up time is set to 30 minutes.
CAUTION
To help protect the environment, conserve energy and avoid inconveniencing others,
do not perform idling when it is unnecessary, or longer than necessary.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
9-6. Engine start operation with rear defrost start Up
z Press the function switch once.
The LCD display will appear as shown
on the right.
Function switch
ADVICE
The LCD display will appear when the
switch is released.
z Press the function switch once more
while the above LCD display is shown.
The rear defrost mark will flash.
Function
switch
ADVICE
The LCD display will appear when the
switch is released.
z Press the start switch while the
above LCD display is shown until it
beeps.
After the send mark flashes, the send
operation is completed. After the send
operation is completed, the controller
will send an answer back signal.
Start switch
*Press the start switch within 2 seconds after the
LCD display appears. If the start switch is not
pressed in time and the LCD display disappears,
start the procedure over again from step 1.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
When the remote control receives a
response from the vehicle, it indicates the
engine start operation with a display (on
the right) and a melody.
After 8-15 sec.
ADVICE
The rear defrost operation cannot be
performed without starting the engine.
Engine start
standby
Engine
running
ADVICE
•
•
After the engine start operation is initiated, the controller will automatically send
an answer back.
On some vehicle models, dash light does not turn on when the rear defrost is
turned on with the Remote Engine Start.
•
•
The rear defrost will automatically stop when the engine stops.
The rear defrost will automatically stop after 15 minutes of operation on some
vehicle models.
Note
•
The rear defrost will turn on about 7 seconds after the engine starts, when
performing this rear defrost operation.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
9-7. Car find function
Car find switch
z Press the car find switch until it
beeps.
The LCD display will appear as
shown on the right.
After the send mark flashes, the send
operation is completed. After the
send operation is completed, the
controller will send an answer back
signal.
When the remote control receives a
response from the vehicle, it
indicates the car find operation with a
display (on the right) and a melody.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Troubleshooting
z Even if you think the device has broken down or malfunctioned, check
once more to be sure.
z If an error occurs, read through this instruction manual thoroughly, and
check the following items in the table below. If the error or problem persists,
do not try to repair the device by yourself. Consult with the authorized
Mazda dealer where you purchased the vehicle or device.
Problem
Remote control
does not work
Check Item
Are the batteries inserted
correctly?
Troubleshoot
Check the status of the batteries.
(Refer to p.13.)
Have the batteries run
out?
Replace the batteries with new ones.
(Refer to p.13.)
Did you press more than
one switch at the same
Refer to the basic operation items to perform
the remote control operation correctly.
time? (except the warm-up (Refer to p.14.)
time setting operation)
Did you try to conduct an
operation too quickly right
after another operation
was sent?
The next transmission cannot be sent while
the LCD display appears. Wait until the
display turns off before conducting an
operation.
(Refer to p.12.)
Engine does
not start using
remote control
Did you make a mistake
with the "Engine start"
operation on the remote
control?
Refer to the "Engine start operation" section
on p.15.
When the function or start
switch was pressed, was
another switch pressed at
the same time or ahead of
those switches?
Do not press another switch at the same time
or ahead of those switches.
Have the engine start
conditions been satisfied?
Does the Error display
appear on the LCD
monitor of the remote
control?
Check the engine start conditions. (Refer to
p.14, p.16.)
Refer to the "Condition Error Display" section
on p.16.
Engine stops
after starting it
with the remote
control
Are the engine stop
conditions shown in p.19
true?
The engine will stop if one of the conditions
shown in p.19 is true.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check Item
Troubleshoot
The headlight
or taillight turns
on when the
engine has
Is the light switch set to the The headlight or taillight will turn on if the
"AUTO" position?
engine is started at night with the remote
control, when the light switch is set to the
"AUTO" position.
been started
with the remote
control
Engine does
not stop using
remote control
Did you make a mistake
with the “Engine stop”
operation on the remote
control?
Refer to the “Engine stop operation” section
on p.18.
When the stop switch was
pressed, was another
switch pressed at the
same time or ahead of the
stop switch?
Do not press another switch at the same time
or ahead of the stop switch.
Was the engine started
using another method
other than the Remote
Engine Start?
If the engine is started using another method
other than the Remote Engine Start, it cannot
be stopped with the remote control.
Warm up time
check does not
work
Did you make a mistake
with the "Warm up time
check" operation on the
remote control?
Refer to the "Warm up time check" section on
p.20.
When the function or start
switch was pressed, was
another switch pressed at
the same time or ahead of
those switches?
Do not press another switch at the same time
or ahead of those switches.
Was the engine started
using another method
other than the Remote
Engine Start?
If the engine is started using another method
other than the Remote Engine Start, it cannot
check warm up time.
Warm up time
remaining
appeared on
the LCD
Warm up time remaining appeared on the
LCD monitor is expressed as the value of a
unit for 2 minutes.
monitor of the
remote control
is different from
its actual time.
―
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check Item
Troubleshoot
Vehicle status
check does not
work
Did you make a mistake
with the "Vehicle status
check" operation on the
remote control?
Refer to the "Vehicle status check" section on
p. 21.
When the function switch
was pressed, was another
switch pressed at the
same time or ahead of the
function switch?
Do not press another switch at the same time
or ahead of the function switch.
The letter of "t"
appeares on
the LCD
Consult with the authorized Mazda dealer
where you purchased the vehicle or device.
―
monitor of the
remote control
RUN mark
Was the engine started
using another method
other than the Remote
Engine Start?
If the engine is started using another method
other than the Remote Engine Start, RUN
mark does not turn on.
does not turn
on when the
engine has
been started
with the push
start switch
Warm up time
settings does
not work
Did you make a mistake
with the "Warm up time
settings" operation on the
remote control?
Refer to the "Warm up time settings" section
on p.22.
When the function and
Do not press another switch at the same time
start switch was pressed at or ahead of those swiches.
the same time, was
another switch pressed at
the same time or ahead of
those switches?
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check Item
Troubleshoot
The rear
defrost does
not turns on
Did you make a mistake
with the "Engine start with
rear defrost start Up"
operation on the remote
control?
Refer to the "Engine start operation with rear
defrost start Up" section on p.23.
When the function or start
switch was pressed, was
another switch pressed at
the same time or ahead of
those switches?
Do not press another switch at the same time
or ahead of those swiches.
Did you operate the
"Engine start with rear
defrost start Up" with the
remote control after the
engine started?
The "Engine start with rear defrost start Up"
operation cannot be performed after the
engine started.
After the engine started,
have approx.15 minutes
passed?
The rear defrost will automatically stop after
15 minutes from the engine started.
The rear
Is the cabin temperature
5℃(41°F) or less?
The rear defrost will automatically turn on
when the cabin temperature is 5℃(41°F) or
less and the engine is started with the
Remote Engine Start.
defrost turns on
in spite of the
"Engine start
operation"
shown in p.15.
The dash light
does not turn
on when the
rear defrost is
turned on with
the Remote
The dash light will not turn on when the rear
defrost is turned on with the Remote Engine
Start.
―
Engine Start
Car find does
not work
Did you make a mistake
with the "Car find"
operation on the remote
control?
Refer to the "Car find function" section on p.
25.
When the car find switch
was pressed, was another
switch pressed at the
same time or ahead of the
car find switch?
Do not press another switch at the same time
or ahead of the car find switch.
Is the ignition switch set to
ON?
The car find will not work when the ignition
switch is set to ON.
Are the turn signal lamps
flashing with the turn
signal switch operation?
The hazard flashing by the car find function
will not work while the turn signal lamps are
flashing.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check Item
Troubleshoot
Remote control
operating
distance is
short
Have the batteries run
out?
Are you too far from the
vehicle?
Replace the batteries with new ones. (Refer
to p.13)
Approach the vehicle and try operating the
remote control.
Is there something
blocking the signal
between the remote
control and the vehicle,
such as a building?
Have the batteries run
out?
Move and try operating the remote control
from a better location, or move closer to the
vehicle when operating the remote control.
Displays a
receive error
"Er"
Replace the batteries with new ones. (Refer
to p.13)
Approach the vehicle and try operating the
remote control.
Are you too far from the
vehicle?
Is there something
blocking the signal
between the remote
control and the vehicle,
such as a building?
Move and try operating the remote control
from a better location, or move closer to the
vehicle when operating the remote control.
Was the engine started (or The send operation from the controller may
the hazard lights flashed)
with the engine start
operation (or the car find
operation) even if the
remote control displayed a
receive error?
be restricted due to the transmission
conditions in the area.
(Refer to p.12.)
Displays a
send error
"BUSY"
The send operation is restricted due to the
transmission conditions in the area. Wait until
the display mark turns off before operating
the remote control. (Refer to p.12.)
―
30
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Servicing
Servicing
If you are having a problem with the device, first re-read this instruction manual
again to troubleshoot the problem or issue. If the problem or issue does not
improve, consult with the authorized Mazda dealer where you purchased the
vehicle or device. If you lose the remote control, contact the authorized Mazda
dealer where you purchased the vehicle or device.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Specifications
Remote Control
Applicable standard
Transmission
frequency
FCC and IC conforming
429.2125MHz
Transmission
method
Operating
Single message transmission
-10 to +60 ºC
temperature range
Battery type
Battery life
Coin type, lithium battery CR2032 / Qty. 2
Approximately 1 year (When starting the engine 5
times / day. However, the battery life for the
batteries included in the accessories is not
guaranteed.)
Dimensions
Weight
Transmission
time
30 × 97 × 19 (mm)
Approximately 50 g (including the batteries)
Approximately 3 seconds
Transmission
rest time
Transmission
antenna
2 seconds or more
Built-in antenna
Controller
Applicable standard
Transmission
frequency
FCC and IC conforming
429.2125MHz
Transmission
method
Operating
Single message transmission
-40 to +85ºC
temperature range
Rated voltage
Power consumption
during standby
Dimensions
DC 13.5 V
3mA or less
201 × 46 × 26 (mm)
(Max. dimensions include antenna)
Receiving antenna
Coaxial cable whip antenna
The specification and external appearance may change without prior
notice given.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Request for Dealer Performing
Installation Service
Be sure to explain the device operation to the customer.
• Note that some contents of this instruction manual may not match the actual
device due to changes in the vehicle or product specification.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
|