Precision Touch Control 500
Electric Smoothtop
Use and Care Guide
Table of Contents
Important Safety
Instructions ............................... 1-3
Surface Cooking .................... 9-12
Surface Controls
Smoothtop Surface
Care & Cleaning ....................... 4-6
Self-Clean Oven
Oven Cooking .......................12-18
Cleaning Procedures
Baking
Cook & Hold
Delay Cook & Hold
Keep Warm
Maintenance................................. 7
Oven Window
Oven Light
Broiling
Sabbath Mode
Troubleshooting ....................... 8-9
Oven Racks
Warranty & Service.................... 19
Form No. A/01/08
Part No. 8113P692-60
©2006 Maytag Appliances Sales Co.
All rights reserved.
Litho U.S.A .
Download from Www.Somanuals.com. All Manuals Search And Download.
Child Safety
Cooking Safety
Never heat an unopened food container in the oven.
Pressure build-up may cause container to burst resulting
in serious personal injury or damage to the appliance.
CAUTION
NEVER store items of interest to children in cabinets
above an appliance. Children climbing on the appliance
or on the appliance door to reach items could be
seriously injured.
Use dry, sturdy potholders. Damp potholders may cause
burns from steam. Dish towels or other substitutes should
never be used as potholders because they can trail across
hot elements and ignite or get caught on appliance parts.
NEVER leave children alone or unsupervised near the
appliance when it is in use or is still hot. Children should
never be allowed to sit or stand on any part of the
appliance as they could be injured or burned.
Wear proper apparel. Loose fitting or long hanging-
sleeved apparel should not be worn while cooking.
Clothing may ignite and cause burns if garment comes in
contact with heating elements.
Children must be taught that the appliance and utensils in
it can be hot. Let hot utensils cool in a safe place, out of
reach of small children. Children should be taught that an
appliance is not a toy. Children should not be allowed to
play with controls or other parts of the appliance.
Always place oven racks in the desired positions while
oven is cool. Slide oven rack out to add or remove food,
using dry, sturdy potholders. Always avoid reaching into
the oven to add or remove food. If a rack must be moved
while hot, use a dry potholder. Do not let potholder
contact hot element in oven.
About Your Appliance
Use racks only in the oven in which they were shipped/
purchased.
CAUTION
Use care when opening the oven door. Let hot air or steam
escape before removing or replacing food.
NEVER use an appliance as a step to reach cabinets
above. Misuse of appliance door, such as stepping,
leaning or sitting on the door, may result in possible
tipping of the appliance, breakage of door, and serious
injuries.
PREPARED FOOD WARNING: Follow food
manufacturer’s instructions. If a plastic frozen food
container and/or its cover distorts, warps, or is otherwise
damaged during cooking, immediately discard the food
and its container. The food could be contaminated.
To prevent potential hazard to the user and damage to the
appliance, do not use appliance as a space heater to heat
or warm a room. Also, do not use the oven as a storage
area for food or cooking utensils.
Do not allow aluminum foil or meat probe to contact
heating element.
Always turn off all controls when cooking is completed.
Do not obstruct the flow of air by blocking the oven vent.
Utensil Safety
DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
SURFACES OF OVEN. Heating elements may be hot even
though they are dark in color. Interior surfaces of any
oven become hot enough to cause burns. During and
after use, do not touch, or let clothing or other flammable
materials contact heating elements or interior surfaces of
oven until they have had sufficient time to cool. Other
surfaces of the appliance may become hot enough to
cause burns – among these surfaces are: oven vent
opening and surface near this opening, oven door,
window of oven door.
Follow the manufacturer’s directions when using oven
cooking bags.
This appliance has been tested for safe performance
using conventional cookware. Do not use any devices or
accessories that are not specifically recommended in this
guide. Do not use add-on oven convection systems. The
use of devices or accessories that are not expressly
recommended in this guide can create serious safety
hazards, result in performance problems, and reduce the
life of the components of the appliance.
If pan is smaller than element, a portion of the element
will be exposed to direct contact and could ignite clothing
or potholder.
Do not touch a hot oven light bulb with a damp cloth as
the bulb could break. Should the bulb break, disconnect
power to the appliance before removing bulb to avoid
electrical shock.
Only certain types of glass, glass/ceramic, ceramic,
earthenware, or other glazed utensils are suitable for
cooktop or oven service without breaking due to the
sudden change in temperature. Follow utensil
manufacturer’s instructions when using glass.
NEVER use aluminum foil to cover an oven rack or oven
bottom. Misuse could result in risk of electric shock, fire,
or damage to the appliance. Use foil only as directed in
this guide.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn pan handle toward center of cooktop, not out into
the room or over another surface element. This reduces
the risk of burns, ignition of flammable materials, or
spillage if pan is accidently bumped or reached by small
children.
Self-Clean Oven
CAUTION
Before self-cleaning the oven, remove the oven
racks, broiler pan, food and any other utensils. Wipe
spillovers to prevent excessive smoke and flare-ups.
Cooktop
NEVER leave surface units unattended, especially when
using high heat. An unattended boilover could cause
smoking and a greasy spillover can cause a fire.
Do not clean door gasket. The door gasket is essential for
a good seal. Care should be taken not to rub, damage, or
move the gasket.
This appliance is equipped with different sized surface
elements. Select pans with flat bottoms large enough to
cover element. Fitting pan size to element will improve
cooking efficiency.
Do not use oven cleaners or oven liners of any kind in or
around any part of the self-clean oven.
Important Safety Notice
and Warning
GLASS-CERAMIC SURFACE: NEVER cook on broken
cooktop. If cooktop should break, cleaning solutions and
spillovers may penetrate the broken cooktop and create a
risk of electric shock. Contact a qualified technician
immediately.
The California Safe Drinking Water and Toxic Enforcement
Act of 1986 (Proposition 65) requires the Governor of
California to publish a list of substances known to the
State of California to cause cancer or reproductive harm,
and requires businesses to warn customers of potential
exposures to such substances.
Deep Fat Fryers
Use extreme caution when moving the grease pan or
disposing of hot grease. Allow grease to cool before
attempting to move pan.
Users of this appliance are hereby warned that when the
oven is engaged in the self-clean cycle, there may be
some low-level exposure to some of the listed substances,
including carbon monoxide. Exposure to these substances
can be minimized by properly venting the oven to the
outdoors by opening the windows and/or door in the room
where the appliance is located during the self-clean cycle.
Ventilating Hoods
Clean range hood and filters frequently to prevent grease
or other flammable materials from accumulating on hood
or filter and to avoid grease fires.
IMPORTANT NOTICE REGARDING PET BIRDS: Never
keep pet birds in the kitchen or in rooms where the fumes
from the kitchen could reach. Birds have a very sensitive
respiratory system. Fumes released during an oven
self-cleaning cycle may be harmful or fatal to birds. Fumes
released due to overheated cooking oil, fat, margarine and
overheated non-stick cookware may be equally harmful.
When flaming foods under the hood, turn the fan on.
Cleaning Safety
Clean cooktop with caution. Turn off all controls and wait
for appliance parts to cool before touching or cleaning.
Clean with caution. Use care to avoid steam burns if a
wet sponge or cloth is used to wipe spills on a hot
surface. Some cleaners can produce noxious fumes if
applied to a hot surface.
Clean only parts listed in this guide.
Save These Instructions for Future Reference
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Care & Cleaning
To set Self-Clean:
Important: Oven temperature must be below 400° F to
program a clean cycle.
Self-Clean Oven
CAUTION
1. Close the oven door.
• It is normal for parts of the range to become hot during a
self-clean cycle.
2. Press the Clean pad.
• CLEAN flashes in the display.
3. Press the More+ or Less- pad.
• CL-M (Medium Soil, 3 hours) is displayed.
• To prevent damage to oven door, do not attempt to open
the door when LOCK is displayed.
• Avoid touching cooktop, door, window or oven vent area
during a clean cycle.
If the door is not closed, beeps will sound and “door” will
display. If the door is not closed within 45 seconds, the
self-cleaning operation will be canceled and the display
will return to the time of day.
• Do not use commercial oven cleaners on the oven finish
or around any part of the oven. They will damage the
finish or parts.
4. Press the More+ or Less- pad to scroll through
The self-clean cycle uses above-normal cooking temperatures
to automatically clean the oven interior.
the self-cleaning settings.
CL-H (Heavy Soil, 4 hours)
CL-M (Medium soil, 3 hours)
CL-L (Light Soil, 2 hours)
The oven should be cleaned regularly by wiping up spillovers
to prevent excessive smoke and flare-ups. Do not allow a
heavy build-up of soil to accumulate in the oven.
During the cleaning process, the kitchen should be well
ventilated to get rid of normal odors associated with cleaning.
Choosing the soil level of the oven automatically programs
the self-cleaning time.
5. After four seconds, the oven will start cleaning.
• The cleaning time will start counting down in the display.
• LOCK will appear in the display.
Before Self-Cleaning
1. Turn off the oven light before cleaning. The light may burn
out during the clean cycle.
2. Remove all pans and oven racks from the oven. The oven
racks will discolor and may not slide easily after a self-
clean cycle if they are not removed.
• CLEAN will appear in the display.
To Delay a Self-Clean Cycle:
1. Press the Delay pad.
3. Clean oven frame, door frame, area
outside of gasket, and around the
opening in the door gasket with a
nonabrasive cleaner such as Bon
Ami* or detergent and water. The
self-cleaning process does not
• DELAY flashes.
• 00:00 will appear in the display.
2. Press the More+ or Less- pad to set the
amount of time you want to delay the cycle.
Delay time can be set from ten minutes (00:10)
to 11 hours, 59 minutes (11:59).
clean these areas. They should be
cleaned to prevent soil from baking
on during the clean cycle. (The gasket is the seal around
the oven door and window.)
3. While DELAY is flashing, press the
Clean pad.
4. To prevent damage, do not clean or rub the gasket around
the oven door. The gasket is designed to seal in heat
during the clean cycle.
• CLEAN will flash.
4. Press the More+ or Less- pad.
• CL-M (Medium Soil, 3 hours) is displayed.
5. Wipe up excess grease or spillovers from the oven bottom.
This prevents excessive smoking, flare-ups or flaming
during the clean cycle.
5. Press the More+ or Less- pad to scroll through the
self-cleaning settings.
6. Wipe up sugary and acidic spillovers such as sweet
potatoes, tomato, or milk-based sauces. Porcelain enamel
is acid-resistant, not acid-proof. The porcelain finish may
discolor if acidic spills are not wiped up before a self-clean
cycle.
CL-H (Heavy Soil, 4 hours)
CL-M (Medium soil, 3 hours)
CL-L (Light Soil, 2 hours)
Choosing the soil level of the oven automatically programs
the self-cleaning time.
Cont.
* Brand names for cleaning products are registered trademarks of the respective manufacturers.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
6. After four seconds, CLEAN, DELAY and LOCK will appear
in the display to show that the oven is set for a delayed
clean operation. The delay time is displayed.
Fine lines may appear in the porcelain because it went
through heating and cooling. This is normal and will not
affect performance.
A white discoloration may appear after cleaning if acidic
or sugary foods were not wiped up before the self-clean
cycle. This discoloration is normal and will not affect
performance.
If the oven has already been set for a clean
cycle and you wish to set a delay:
Notes:
• If the oven door is left open, “door” will flash in the
display and a signal will beep until the door is closed
and the Clean pad is pressed again.
1. Press the Delay pad.
• DELAY flashes.
• 00:00 will appear in the display.
• If more than five seconds elapse between pressing the
Clean pad and the More+ or Less- pad, the program
will automatically return to the previous display.
2. Press the More+ or Less- pad to set the
amount of time you want to delay the cycle.
After four seconds, CLEAN, DELAY and LOCK
will appear in the display to show that the
oven is set for a delayed clean operation. The
delay time is displayed.
• The oven door will be damaged if the oven door is
forced to open when LOCK is still displayed.
Cleaning Procedures
When the Self-Clean cycle starts:
• DELAY will turn off.
CAUTION
• The clean time will appear in the display.
To cancel the Self-Clean cycle:
Press the CANCEL pad.
• Be sure appliance is off and all parts are cool before
handling or cleaning. This is to avoid damage and
possible burns.
• All words disappear from the display.
• All functions are canceled.
• To prevent staining or discoloration, clean appliance after
each use.
• If a part is removed, be sure it is correctly replaced.
• The time of day appears in the display.
Backguard and Cooktop – Porcelain Enamel
During the Self-Clean Cycle
Porcelain enamel is glass fused on metal and may crack or
chip with misuse. It is acid-resistant, not acid-proof. All
spillovers, especially acidic or sugary spillovers, should be
wiped up immediately with a dry cloth.
When LOCK shows in the display, the door cannot be opened.
To prevent damage to the door, do not force the door open
when LOCK is displayed.
• When cool, wash with soapy water, rinse and dry.
Smoke and Smells
You may see some smoke and smell an odor the first few times
the oven is cleaned. This is normal and will lessen in time.
• Never wipe off a warm or hot surface with a damp cloth.
This may cause cracking or chipping.
• Never use oven cleaners, abrasive or caustic cleaning
agents on exterior finish of range.
Smoke may also occur if the oven is heavily soiled or if a pan
was left in the oven.
Sounds
Clock and Control Pad Area
• To activate control lock for cleaning, see Locking the
Controls page 13.
As the oven heats, you may hear sounds of metal parts
expanding and contracting. This is normal and will not
damage the oven.
• Wipe with a damp cloth and dry. Do not use abrasive
cleaning agents as they may scratch the surface.
After Self-Cleaning
• Glass cleaners may be used if sprayed on a cloth first.
About one hour after the end of the self-clean cycle, LOCK will
turn off. The door can then be opened.
DO NOT spray directly on control pad and display area.
Control Knobs
• Remove knobs in the OFF position by pulling forward.
• Wash, rinse and dry. Do not use abrasive cleaning agents
as they may scratch the finish.
Some soil may leave a light gray, powdery ash. Remove it
with a damp cloth. If soil remains after wiping, that means the
clean cycle was not long enough. The soil will be removed
during the next clean cycle.
• Turn on each element to be sure the knobs have been
correctly replaced.
If oven racks were left in the oven and do not slide
smoothly after a clean cycle, wipe racks and rack supports
with a small amount of vegetable oil to make them easier to
move.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooktop – Glass-Ceramic
Oven Racks
Never use oven cleaners, chlorine bleach, ammonia or
glass cleaners with ammonia. Important: Call an
authorized servicer if the glass-ceramic top should
crack, break or if metal or aluminum foil should melt on
the cooktop.
• Clean with soapy water.
• Remove stubborn soil with cleansing powder or soap-filled
scouring pad. Rinse and dry.
• Racks will permanently discolor and may not slide smoothly
if left in the oven during a self-clean operation. If this
occurs, wipe the rack edge and rack support with a small
amount of vegetable oil to restore ease of movement, then
wipe off excess oil.
• Allow the cooktop to cool before cleaning.
• General – Clean cooktop after each use, or when needed,
with a damp paper towel and Cooktop Cleaning
Creme* (Part No. 20000001)**. Then, buff with a clean, dry
cloth.
Stainless Steel (select models)
• DO NOT USE ANY CLEANING PRODUCT CONTAINING
CHLORINE BLEACH.
Important: Permanent stains will develop if soil is allowed to
cook on by repeatedly using the cooktop when soiled.
• DO NOT USE ABRASIVE OR ORANGE CLEANERS.
• ALWAYS WIPE WITH THE GRAIN WHEN CLEANING.
• Heavy Soils or Metal Marks – Dampen a “scratchless” or
“never scratch” scrubber sponge. Apply Cooktop Cleaning
Creme* (Part No. 20000001)** and scrub to remove as much
soil as possible. Apply athin layer of the creme over the soil,
cover with a damp paper towel and let stand 30 to 45
minutes (2-3 hours for very heavy soil). Keep moist by
covering the paper towel with plastic wrap. Scrub again,
then buff with a clean dry cloth.
• Daily Cleaning/Light Soil –– Wipe with one of the
following - soapy water, white vinegar/water solution,
Formula 409 Glass and Surface Cleaner* or a similar glass
cleaner - using a sponge or soft cloth. Rinse and dry. To
polish and help prevent fingerprints, follow with Stainless
Steel Magic Spray (Part No. 20000008)**.
• Moderate/Heavy Soil –– Wipe with one of the following -
Bon Ami*, Smart Cleanser*, or Soft Scrub* - using a damp
sponge or soft cloth. Rinse and dry. Stubborn soils may be
removed with a damp multi-purpose Scotch-Brite* pad; rub
evenly with the grain. Rinse and dry. To restore luster and
remove streaks, follow with Stainless Steel Magic
Spray*.
Important: Only use a CLEAN, DAMP “scratchless” pad that
is safe for non-stick cookware. The pattern and glass will be
damaged if the pad is not damp, if the pad is soiled, or if
another type of pad is used.
• Burned-on or Crusty Soils – Scrub with a “scratchless” or
“never scratch” scouring pad and Cooktop Cleaning Creme*.
Important: Hold a razor blade scraper at 30° angle and
scrape any remaining soil. Then, clean as described above. Do
not use the razor blade for daily cleaning as it may wear the
pattern on the glass.
• Discoloration –– Using a damp sponge or
soft cloth, wipe with Cameo Stainless Steel
Cleaner*. Rinse immediately and dry. To
remove streaks and restore luster,
follow with Stainless Steel Magic Spray*.
• Melted Sugar or Plastic – Immediately turn element to
Low and scrape sugar or plastic from hot surface to a cool
area. Then turn element OFF and allow to cool. Clean
residue with razor blade scraper and Cooktop Cleaning
Creme*.
Storage Drawer, Door Handle, Side Panels –
Painted Enamel
• When cool, wash with warm soapy water, rinse and dry.
Never wipe a warm or hot surface with a damp cloth as this
may damage the surface and may cause a steam burn.
Oven Window and Door – Glass
• Avoid using excessive amounts of water which may seep
under or behind glass, causing staining.
• For stubborn soil, use mildly abrasive cleaning agents such
as baking soda paste or Bon Ami.* Do not use abrasive,
caustic or harsh cleaning agents such as steel wool pads or
oven cleaners. These products will scratch or permanently
damage the surface.
• Wash with soap and water. Rinse with clear water and dry.
Glass cleaner can be used if sprayed on a cloth first.
• Do not use abrasive materials such as scouring pads, steel
wool or powdered cleaners as they will scratch glass.
Important: Use a dry towel or cloth to wipe up spills,
especially acidic or sugary spills. Surface may discolor
or dull if soil is not immediately removed. This is
especially important for white surfaces.
Oven Interior
• Follow instructions on pages 4-5 to set a self-clean cycle.
* Brand names are registered trademarks of the respective manufacturers.
** To order call 1-877-232-6771 USA and 1-800-688-8408 Canada.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Oven Door
Leveling Legs
CAUTION
CAUTION
Be sure the anti-tip bracket secures one of the
rear leveling legs to the floor. This bracket
prevents the range from accidentally tipping.
Do not place excessive weight on or stand on an open
oven door. This could cause the range to tip over, break the
door, or injure the user.
Important: The oven door on a new range may feel “spongy”
when it is closed. This is normal and will decrease with use.
Be sure the range should be leveled when
installed. If the range is not level, turn the
leveling legs, located at each corner of
the range, until range is level.
ANTITIP BRACKET
ANTI-TIP
BRACKET
Oven Window
LLEVEILINGLEG
Oven Light
To protect the oven door window:
1. Do not use abrasive cleaning agents such as steel wool
scouring pads or powdered cleansers as they may scratch
the glass.
CAUTION
• Disconnect power to range before replacing light bulb.
• Allow oven to cool before replacing light bulb.
2. Do not hit the glass with pots, pans, furniture, toys, or other
objects.
• Make sure bulb cover and bulb are cool before touching.
3. Do not close the oven door until the oven racks are in
BULB COVER
To replace oven light bulb:
place.
1. When oven is cool, hold bulb
coverinplace,thenslidewire
retaineroffcover.Important:
Bulb cover will fall if not held
Scratching, hitting, jarring or stressing the glass may weaken
its structure causing an increased risk of breakage at a later
date.
WIRE
RETAINER
in place while removing wire
retainer.
Storage Drawer
2. Remove bulb cover and light bulb.
CAUTION
3. Replace with a 40-watt appliance bulb.
4. Replace bulb cover and secure with wire retainer.
5. Reconnect power to range. Reset clock.
Do not store plastic, paper products, food or flammable
materials in this drawer. The drawer may become too warm
for these items when the oven is in use.
Convenience Outlet
The storage drawer can be removed to allow you to clean
under the range.
(Canadian models only)
To remove:
1. Empty drawer and pull out to the first stop position.
The convenience outlet is located on the
lower left side of the backguard. Be sure
appliance cords do not rest on or near
the surface element. If the surface
element is turned on, the cord and
outlet will be damaged.
2. Lift up the front of the drawer.
3. Pull out to the second stop position.
4. Grasp sides and lift drawer up and out.
To replace:
The convenience outlet circuit breaker
may trip if the small appliance plugged
into it exceeds 10 amps. To reset the circuit breaker, press the
switch located on the lower edge of the backguard.
CIRCUIT BREAKER
1. Fit the ends of the drawer glides into the rails in the range.
2. Lift up the front of the drawer and gently push in to the first
stop position.
3. Lift drawer up again and push until drawer is closed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
For most concerns, try these first.
Oven did not clean properly.
• Longer cleaning time may be needed.
• Excessive spillovers, especially sugary and/or acidic foods,
were not removed prior to the self-clean cycle.
• Check if oven controls have been properly set.
• Check to be sure plug is securely inserted into receptacle.
• Check or re-set circuit breaker. Check or replace fuse.
• Check power supply.
Oven door will not unlock after self-clean cycle.
• Oven interior is still hot. Allow about one hour for the oven
to cool after the completion of a self-clean cycle. The door
can be opened when the LOCK indicator word is not
displayed.
Part or all of appliance does not work.
• Check if surface and/or oven controls have been properly
set. See pages 9-10 & 12-17.
• Check if oven door is unlocked after self-clean cycle. See
page 5.
• The control and door may be locked. See page 5.
Smoothtop surface shows wear.
• Tiny scratches or abrasions.
• Check if oven is set for a delayed cook or clean program.
See pages 5 & 14.
- Make sure cooktop and pan bottom are clean. Do not
slide glass or metal pans across top. Make sure pan
bottom is not rough. Use the recommended cleaning
agents. See page 6.
• Check if Control Lock is activated. See page 13.
• Check if control is in Sabbath Mode. See page 17.
Clock, indicator words, and/or lights operate but oven
does not heat.
• Metal marks.
- Do not slide metal pans across top. When cool, clean
• Oven may be set for a Cook & Hold or Delay function.
• The Control Lock may have been set. See page 13.
with Cooktop Cleaning Creme. See page 6.
• Brown streaks and specks.
Baking results are not as expected or differ from
previous oven.
• Make sure the oven vent has not been blocked. See page
17 for location.
- Remove spills promptly. Never wipe with a soiled cloth or
sponge. Make sure cooktop and pan bottom are clean.
• Areas with a metallic sheen.
- Mineral deposits from water and food. Use recommended
cleaning agents. See page 6.
• Check to make sure range is level.
• Pitting or flaking.
- Remove sugary boilovers promptly. See page 6.
• Temperatures often vary between a new oven and an old
one. As ovens age, the oven temperature often “drifts” and
may become hotter or cooler. See page 16 for instructions
on adjusting the oven temperature. Important: It is not
recommended to adjust the temperature if only one or two
recipes are in question.
Moisture collects on oven window or steam comes from
oven vent.
• This is normal when cooking foods high in moisture.
• Excessive moisture was used when cleaning the window.
Food is not broiling properly or smokes excessively.
• Check oven rack positions. Food may be too close to
element.
• Broil element was not preheated.
• Aluminum foil was incorrectly used. Never line the broiler
There is a strong odor or light smoke when oven is
turned on.
• This is normal for a new range and will disappear after a few
uses. Initiating a clean cycle will “burn off” the odors more
quickly.
• Turning on a ventilation fan will help remove the smoke
and/or odor.
• Excessive food soils on the oven bottom. Use a self-clean
cycle.
insert with foil.
• Oven door was closed during broiling. Leave the door open
to the first stop position (about 4 inches).
• Trim excess fat from meat before broiling.
• A soiled broiler pan was used.
Fault Codes
• Voltage in house may be low.
• BAKE or LOCK may flash rapidly in the display to alert you if
there is an error or a problem. If BAKE or LOCK appear in
the display, press CANCEL pad. If BAKE or LOCK continue
to flash, disconnect power to the appliance. Wait a few
minutes, and then reconnect power. If the flashing still
continues, disconnect power to the appliance and call an
Oven will not self-clean.
• Check to make sure the cycle is not set for a delayed start.
See page 5.
• Check if door is closed.
• Check if control is in Sabbath Mode. See page 17.
• Oven may be over 400° F. Oven temperature must be below
400° F to program a clean cycle.
authorized servicer.
Cont.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
• If the oven is heavily soiled, excessive flareups may result in
a fault code during cleaning. Press the CANCEL pad and
allow the oven to cool completely, wipe out excess soil, then
reset the clean cycle. If the fault code reappears, contact an
authorized servicer.
There are no beeps and no display.
• Oven may be in Sabbath Mode. See page 16.
SAb flashing and then displayed continuously.
• Oven is in Sabbath Mode. To cancel, press and hold the
Clock pad for five seconds.
Noises may be heard.
• The oven makes several low level noises. You may hear the
oven relays as they go on and off. This is normal.
• As the oven heats and cools, you may hear sounds of metal
parts expanding and contracting. This is normal and will not
damage your appliance.
Surface Cooking
When a control is turned on, a glow can be seen through
the smoothtop surface. The element will cycle on and off
to maintain the preset heat setting, even on High.
Surface Controls
Use to turn on the surface elements. An infinite choice of
heat settings is available from Low to High. The knobs can
be set on or between any of the settings.
4. After cooking, turn knob to OFF. Remove pan.
Dual Elements
Setting the Controls
The cooking surface has two dual elements
located in the right front and left front of
the smoothtop. This allows you to change
the size of these elements.
1. Place pan on surface element.
2. Push in and turn the knob in either direction to the desired
heat setting.
• The control panel is marked to identify which
element the knob controls. For example, the
graphic at right indicates left front element.
Press the switch to the left to use the
large element or to the right to use the
small element. The selection should be
made before turning on the element.
3. There is an element indicator light on the control panel.
When any surface control knob is turned on, the light will
turn on. The light will turn off when all the surface
elements are turned off.
CAUTION
AFTER COOKING
• Make sure surface unit is turned off.
• Clean up messy spills as soon as possible.
BEFORE COOKING
• Always place a pan on the surface unit before you turn it
on. To prevent damage to range, never operate surface
unit without a pan in place.
• NEVER use the cooktop as a storage area for food or
cookware.
OTHER TIPS
• If cabinet storage is provided directly above cooking
surface, limit it to items that are infrequently used and can
be safely stored in an area subjected to heat. Tempera-
tures may be unsafe for items such as volatile liquids,
cleaners or aerosol sprays.
• NEVER leave any items, especially plastic items, on the
cooktop. The hot air from the vent may ignite flammable
items, melt or soften plastics, or increase pressure in
closed containers causing them to burst.
• NEVER allow aluminum foil, meat probes or any other
metal object, other than a pan on a surface element, to
contact heating elements.
• NEVER store heavy items above the cooktop that could fall
and damage it.
DURING COOKING
• Be sure you know which knob controls which surface
unit. Make sure you turned on the correct surface unit.
• Begin cooking on a higher heat setting then reduce to a
lower setting to complete the operation. Never use a
high heat setting for extended cooking.
• NEVER allow a pan to boil dry. This could damage the
pan and the appliance.
• NEVER touch cooktop until it has cooled. Expect some
parts of the cooktop, especially around the surface units,
to become warm or hot during cooking. Use potholders
to protect hands.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
For more information on cookware, refer to Cookware
Suggested Heat Settings
The size, type of cookware and cooking operation will affect
the heat setting. For information on cookware and other
factors affecting heat settings, refer to
Cookware Recommendations on
Recommendations on page 11.
SINGLE
ELEMENT
WARMING CENTER
SINGLE
ELEMENT
page 11.
Low (2): Food maintains a
temperature above 140° F
without continuing to cook. Food
is heated on a higher setting until
it reaches this temperature.
DUAL ELEMENT
(SELECT MODELS)
FLEXCHOICETM
ELEMENT
(SELECT MODELS)
Hot Surface Light
The Hot Surface indicator light is located on the control panel.
The light will be illuminated when any cooking area is hot. It
will remain on, even after the control is turned off, until the
area has cooled.
Med. Low (3-4): Use to continue
cooking covered foods or steam foods.
Medium (5-7): Use to maintain slow boil for large amounts
of liquids and for most frying operations.
FlexChoiceTM Element (select models)
The FlexChoice element is a fully
functioning element that provides an
ultra low (Warm) heat setting for
holding delicate sauces and keeping
cooked foods warm. It is located in the
right rear position
Med. High (8-9): Use to brown meat, heat oil for deep fat
frying or sauteing. Maintain fast boil for large amounts of
liquids.
High (10): Use to bring liquid to a boil. Always reduce
setting to a lower heat when liquids begin to boil or foods
begin to cook.
The Warm setting is located between
Low and OFF. Heat settings outside of
(Control style
Smoothtop Surface
varies by model.)
this area function as a normal
element, with Low to High settings.
Notes:
Important: When using the normal settings for preparing
foods, it may take a few minutes for the cooking area to cool
to the Warm heat setting.
• Cooktop may emit light smoke and odor the first few
times the cooktop is used. This is normal.
• Smoothtop cooktops retain heat for a period of time
after the element is turned off. Turn the elements off
a few minutes before food is completely cooked and use
the retained heat to complete cooking. When the hot
surface light turns off, the cooking area will be cool
enough to touch. Because of the way they retain heat, the
smoothtop elements will not respond to changes in
settings as quickly as coil elements.
Warming Center
Use the Warming Center to keep hot cooked foods warm, such
as vegetables, gravies and oven-safe dinner plates.
Setting the Control:
1. Push in and turn the knob. Warming
temperatures are approximate and
are indicated on the control as Min,
2-8 and Max. However, the control
can be set to any position between
Min and Max.
• In the event of a potential boilover, remove the pan from
the cooking surface.
• Never attempt to lift the cooktop.
2. When done, turn the control toOFFand
• The smoothtop surface may appear discolored when it is
hot. This is normal and will disappear when the surface
cools.
remove food. The Hot Surface indicator light will go off when
the Warming Center surface has cooled.
Important:
• Never warm food for longer than one hour (eggs for 30
minutes), as food quality may deteriorate.
Cooking Areas
The cooking areas on your range are identified by permanent
circles on the smoothtop surface. For most efficient cooking,
fit the pan size to the element size.
1
• Do not heat cold food on the Warming Center.
• Heat settings will vary depending on type and amount
of food. Always hold food at proper food temperatures.
USDA recommends food temperatures between
2
Pans should not extend more than / to 1-inch beyond
the cooking area.
140°-170° F.
Cont.
When a control is turned on, a glow can be seen through the
smoothtop surface. The element will cycle on and off to
maintain the preset heat setting, even on High.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Suggested Settings
Type of food
• To prevent scratching or damage to the glass-ceramic top,
do not leave sugar, salt or fats on the cooking area. Wipe
the cooktop surface with a clean cloth or paper towel
before using.
Setting
Min - 2
Breads/Pastries
Casseroles
Gravies
Eggs
• Never slide heavy metal pans across the surface since
these may scratch.
2 - 5
Dinner Plate with Food
Soups (Cream)
Vegetables
Sauces
Stews
Meats
To Prevent Stains
5 - Max
Fried Foods
Hot Beverages
• Never use a soiled dish cloth or sponge to clean the
cooktop surface. A film will remain which may cause stains
on the cooking surface after the area is heated.
Soups (Liquid)
• Continuously cooking on a soiled surface may/will result in
a permanent stain.
Notes:
• Use only cookware and dishes recommended as safe for
oven and cooktop use.
To Prevent Other Damage
• Do not allow plastic, sugar or foods with high sugar
content to melt onto the hot cooktop. Should this happen,
clean immediately. (See Cleaning, pages 5-6.)
• Always use oven mitts when removing food from the
Warming Center as cookware and plates will be hot.
• All foods should be covered with a lid or aluminum foil to
maintain food quality.
• Never let a pan boil dry as this will damage the surface and
pan.
• When warming pastries and breads the cover should have
an opening to allow moisture to escape.
• Never use cooktop as a work surface or cutting board.
• Never cook food directly on the surface.
• Do not use plastic wrap to cover foods. Plastic may melt
on to the surface and be very difficult to clean.
• Do not use a small pan on a large element. Not only does
this waste energy, but it can also result in spillovers burning
onto the cooking area which requires extra cleaning.
• Do not use non-flat specialty items that are oversized or
uneven such as round bottom woks, rippled bottom and/or
oversized canners and griddles.
Tips to Protect the
Smoothtop Surface
• Do not use foil or foil-type containers. Foil may melt onto
the glass. If metal melts on the cooktop, do not use. Call an
authorized servicer.
Cleaning (see page 6 for more information)
• Before first use, clean the cooktop.
• Clean your cooktop daily or after each use. This will keep
your cooktop looking good and can prevent damage.
Cookware Recommendations
Using the right cookware can prevent many problems, such
as food taking longer to cook or achieving inconsistent
results. Proper pans will reduce cooking times, use less
energy, and cook food more evenly.
• If a spillover occurs while cooking, immediately clean the
spill from the cooking area while it is hot to prevent a tough
cleaning chore later. Using extreme care, wipe spill with a
clean, dry towel.
• Do not allow spills to remain on the cooking area or the
cooktop trim for a long period of time.
Flat Pan Tests
• Never use abrasive cleansing powders or scouring pads
which will scratch the cooktop.
See if your pans are flat.
The Ruler Test:
• Never use chlorine bleach, ammonia or other cleansers not
specifically recommended for use on glass-ceramic.
1. Place a ruler across the bottom of the pan.
2. Hold it up to the light.
To Prevent Marks and Scratches
3. Little or no light should be visible under the ruler.
The Bubble Test:
• Do not use glass pans. They may scratch the surface.
• Never place a trivet or wok ring between the surface and
pan. These items can mark or etch the top.
1. Put 1 inch of water in the pan. Place on cooktop and turn
control to High.
• Do not slide aluminum pans across a hot surface. The pans
may leave marks which need to be removed promptly. (See
Cleaning, page 6.)
2. Watch the formation of the bubbles as the water heats.
Uniform bubbles mean good performance, and uneven
bubbles indicate hot spots and uneven cooking.
• Make sure the surface and the pan bottom are clean before
turning on to prevent scratches.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Select
Avoid
Canning and Oversize
Cookware
Flat, smooth-bottom Pans with grooved or warped bottoms.
pans.
Pans with uneven bottoms do not cook
efficiently and sometimes may not
boil liquid.
All canners and large pots must have flat bottoms and
must be made from heavy-gauge materials. This is critical
on smoothtop surfaces. The base must not be more than
1 inch larger than the element.
Heavy-gauge pans. Very thin-gauge metal or glass pans.
Pans that are the
same size as the
element.
Pans smaller or larger than the
element by 1 inch.
When canners and pots do not meet these standards, cooking
times may be longer, and cooktops may be damaged.
Some canners are designed with smaller bases for use on
smoothtop surfaces.
Secure handles.
Cookware with loose or broken handles.
Heavy handles that tilt the pan.
When canning, use the High heat setting only until the
water comes to a boil or pressure is reached in the canner.
Reduce to the lowest heat setting that maintains the boil or
pressure. If the heat is not turned down, the cooktop may be
damaged.
Tight-fitting lids.
Flat bottom woks.
Loose-fitting lids.
Woks with a ring-stand bottom.
Oven Cooking
Control Panel
Clock
Broil
Use for broiling and top browning.
The clock can be set to display time in a 12-hour or 24-hour
format. The clock is set at the factory for the 12-hour format.
Bake
Use for baking and roasting.
More+ or
Less-
Enters or changes time, oven temperature.
Sets HI or LO broil.
To change the clock to 24-hour format:
1. Press and hold the CANCEL and
Timer
Sets Timer.
Delay pads for three seconds.
Cook & Hold Bakes for a preset time, then holds food
warm for 1 hour.
2. Press the More+ or Less - pad to
select 12 or 24 hour.
Clean
Delay
Use to set self-clean cycle.
3. Set the time of day following the
directions below.
Programs the oven to start baking at a
later time.
Clock
Use to set time-of-day clock.
To set the Clock:
1. Press the Clock pad.
Keep Warm
CANCEL
Use to keep cooked food warm in oven.
• The colon flashes in the display.
Cancels all operations except Timer
and Clock.
2. Press the More+ or Less- pad to set the
time of day.
• Colon continues flashing.
Using the Touchpads
• Press the desired pad.
3. Press the Clock pad again or wait four
seconds. The colon stops flashing.
When electrical power is supplied or after a power
interruption, the last clock time before power was interrupted
will flash.
• Press the More+ or Less- pad to enter time or temperature.
• A beep will sound when any pad is touched.
• A double beep will sound if a programming error occurs.
To recall the time of day when another time function is
Important: Four seconds after pressing the More+ or Less-
pad, the time or temperature will automatically be entered. If
more than 30 seconds elapse between touching a function pad
and the More+ or Less- pad, the function will be canceled and
the display will return to the previous display.
showing, press the Clock pad.
Clock time cannot be changed when the oven has been
programmed for Delay Cook or Delay Clean or Cook & Hold.
Cont.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To cancel the Clock display:
To lock:
If you do not want the time of day to display:
Press and hold the CANCEL and Cook &
Hold pads for three seconds. (Press
CANCEL pad first.)
Press and hold the CANCEL and Clock
pads for three seconds. The time of day will
disappear from the display
•
LOCK flashes in the display.
When the clock display is canceled, press
the Clock pad to briefly display the time of
day.
To unlock:
Press and hold the CANCEL and Cook & Hold pads for three
seconds. (Press CANCEL pad first.)
To restore the Clock display:
Press and hold the CANCEL and Clock pads for three
seconds. The time of day will reappear in the display.
•
LOCK disappears from the display.
Fault Codes
BAKE or LOCK may flash rapidly in the display to alert you if
there is an error or a problem. If BAKE or LOCK flash in the
display, press CANCEL pad. If BAKE or LOCK continue to
flash, disconnect power to the appliance. Wait a few minutes,
and then reconnect power. If the flashing still continues,
disconnect power to the appliance and call an authorized
servicer.
Timer
The timer can be set from one minute (0:01) up to 99 hours
and 59 minutes (99:59).
The timer can be used independently of any other oven
activity. It can also be set while another oven function is
operating.
The timer does not control the oven. It only controls a beeper.
Baking
To set the Timer:
1. Press the Timer pad.
To set Bake:
• 0:00 lights in the display.
1. Press the Bake pad.
• The colon flashes in the display.
• BAKE will flash.
2. Press the More+ or Less- pad until the
• 000 will light in the display.
correct time appears in the display.
2. Select the oven temperature. The oven
temperature can be set from 170° to 550°. Press
or press and hold the More+ or Less- pads.
• The colon will continue to flash.
3. Press Timer pad again or wait four seconds.
• 350° will light when either pad is first pressed.
• Press the More+ pad to increase the temperature.
• Press the Less- pad to decrease the temperature.
3. Press Bake pad again or wait four seconds.
• BAKE will stop flashing and light in the display.
• The colon continues flashing and the time begins
counting down.
• The last minute of the timer countdown will be displayed
as seconds.
4. At the end of the set time, one long beep will sound.
To cancel the Timer:
1. Press and hold the Timer pad for three seconds.
OR
2. Press the Timer pad and set the time to 0:00.
• 100° or the actual oven temperature will display. The
temperature will rise in 5° increments until the preset
temperature is reached.
Locking the Control
and Oven Door
4. Allow the oven to preheat for 8-15 minutes.
The touchpad controls and oven door can be locked for
safety, cleaning, or to prevent unwanted use. They will not
function when locked.
• When the set oven temperature is reached, one long
beep will sound.
• To recall the set temperature during preheat, press the
Bake pad.
If the oven is currently in use, the controls and door cannot be
locked.
5. Place food in the oven.
The current time of day will remain in the display when the
controls are locked.
6. Check cooking progress. Cook longer if needed.
7. When cooking is finished, press CANCEL.
8. Remove food from the oven.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
After one hour in HOLD WARM:
Notes:
• “End” will display.
• To change the oven temperature during cooking, press the
Bake pad and then the More+ or Less- pad until the
desired temperature is displayed.
• The time of day reappears in the display.
To cancel Cook & Hold at any time:
Press the CANCEL pad. Remove food from oven.
• To change the oven temperature during preheat, press the
Bake pad twice, then press the More+ or Less- pads
until the desired temperature is displayed.
Delay Cook & Hold
• If you forget to turn off the oven, it will automatically turn
off at the end of 12 hours. If you wish to deactivate this
feature, see page 17.
CAUTION
Do not use delayed baking for highly perishable foods such
as dairy products, pork, poultry, or seafood.
Baking Differences Between Your Old
and New Oven
It is normal to notice some baking time differences between a
new oven and an old one. See Adjusting the Oven Temperature
on page 16.
When using Delay, the oven begins to cook later in the day.
Set the amount of time that you want to delay before the oven
turns on and how long you want to cook. The oven begins to
heat at the selected time and cooks for the specified length of
time, then keeps food warm for up to one hour.
Cook & Hold
Delay time can be set from 10 minutes (00:10) to 11 hours, 59
minutes (11:59).
Cook & Hold allows you to bake for a preset amount of time,
followed by a one-hour Keep Warm cycle.
To set a Delayed Cook & Hold cycle:
1. Press the Delay pad.
To set Cook & Hold:
1. Press the Cook & Hold pad.
• DELAY flashes.
• BAKE and HOLD flash.
• 000 lights in the display.
• 00:00 flashes in the display.
2. Press the More+ or Less- pad to set the
delay time.
2. Select the oven temperature. The oven
temperature can be set from 170° to 550°. Press
or press and hold the More+ or Less- pad.
While DELAY is still flashing:
3. Press the Cook & Hold pad.
• 000 lights in the display.
• BAKE and HOLD flash.
• Press the More+ pad to increase the temperature.
• Press the Less- pad to decrease the temperature.
3. Press Cook & Hold again or wait four seconds.
• HOLD flashes.
4. Press More+ pad to set the baking
temperature.
• 00:00 flashes in the display.
• 00:00 and HOLD flash.
• BAKE stays lit.
4. Enter the amount of time you want to bake by pressing the
More+ or Less- pad. Bake time can be set from ten
minutes (00:10) to 11 hours, 59 minutes (11:59).
5. Press More+ pad to set the baking time.
• The Delay time, DELAY, BAKE and HOLD light in
the display.
• BAKE and HOLD light in the display.
• The baking time will light in the display.
• The baking time will start counting down.
When the cooking time has elapsed:
• Four beeps will sound.
When the Delay time has expired:
• DELAY will turn off.
• BAKE will turn off.
• HOLD and WARM will light.
• 170° will display.
• Baking time is displayed.
• BAKE and HOLD are displayed.
To set a Delay when Cook & Hold has already
been programmed:
1. Press the Delay pad.
• DELAY flashes.
• 00:00 appears in the display.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press the More+ or Less- pad to set the delay
time.
Notes:
• After four seconds, DELAY will stay lit to
remind you that a delayed cooking cycle
has been set.
• For optimal food quality, oven cooked foods should be kept
warm for no longer than 1 to 2 hours.
• To keep foods from drying, cover loosely with foil or a lid.
• To warm dinner rolls:
When the Delay time has expired and
the oven starts:
- cover rolls loosely with foil and place in oven.
- press Keep Warm and More+ pads to set 170° F.
- warm for 12-15 minutes.
• The baking time will be displayed.
• DELAY will turn off.
• BAKE and HOLD will remain lit.
To cancel:
• To warm plates:
- place 2 stacks of up to four plates each in the oven.
- press Keep Warm and More+ pads to set 170° F.
Press the CANCEL pad.
• All timed and untimed cooking functions will be
canceled.
- warm for five minutes, turn off the oven and leave plates
in the oven for 15 minutes more.
• The time of day will reappear in the display.
- use only oven-safe plates, check with the manufacturer.
Important:
- do not set warm dishes on a cold surface as rapid
temperature changes could cause crazing or breakage.
•
Do not use delayed baking for items that require a
preheated oven, such as cakes, cookies, and breads.
•
Do not use delayed baking if oven is already hot.
Changing Temp °F/°C
Keep Warm
1. The factory default setting for temperature is Fahrenheit.
For safely keeping foods warm or for warming breads
and plates.
2. Tochangethesetting,pressandholdtheCANCELandBake
pads at the same time for three seconds.
To set Keep Warm:
1. Press the Keep Warm pad.
• WARM flashes.
3. A single beep will sound and the current setting will be
displayed (°F or °C). (If no change is made, the range will
return to the existing setting after 30 seconds.)
4. To change the setting, press the More+ or Less- pad. Press
again to return to existing setting. Wait five seconds and the
setting will be complete.
• 000 appears in the display.
2. Select the Keep Warm temperature. The Keep
Warm temperature can be set from 145° to
190°. Press or press and hold the More+ or
Less- pad.
Broiling
• 170° will light when either pad is first pressed.
• Press the More+ pad to increase the temperature.
• Press the Less- pad to decrease the temperature.
CAUTION
Use CAUTION when cooking with the Broil feature. The
greasefromfattyfoodsmayignite.Ifafireshouldoccur,close
the oven door and turn the oven OFF. If the fire does not
extinquish, DO NOT put water on the fire. Use baking soda,
dry chemical or fire extinguisher to smother the fire.
WARM and the temperature will be displayed while Keep
Warm is active.
To set Broil:
1. Press the Broil pad.
• BROIL flashes.
• SEt is displayed.
To cancel Keep Warm:
1. Press the CANCEL pad.
2. Remove food from the oven.
2. Press the More+ pad to set HI broil or press the Less-
pad to set LO broil.
• HI or LO will be displayed.
• Select HI broil (550° F) for normal broiling. Select
LO broil (450° F) for low-temperature broiling of longer
cooking foods such as poultry.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Oven Temperature
Oven temperatures are carefully tested for accuracy at the
factory. It is normal to notice some baking or browning
differences between a new oven and an old one. As ranges
get older, the oven temperature can shift.
3. After four seconds, the oven will start.
• BROIL will remain lit.
You may adjust the oven temperature if you think the oven is
not baking or browning correctly. To decide how much to
change the temperature, set the temperature 25° higher or
lower than your recipe recommends, then bake. The results
of the “test” should give you an idea of how much to adjust
the temperature.
4. For optimum browning, preheat broil element for 3-4
minutes before adding food.
5. Place food in the oven. Leave oven door open about four
inches (the first stop).
6. Turn meat once about halfway through cooking.
To adjust the oven temperature:
7. When food is cooked, press the CANCEL
pad. Remove food and broiler pan from the
oven.
1. Press Bake.
2. Enter 550° by pressing the More+ pad.
3. Press and hold the Bake pad for several
• The time of day will reappear in the display.
seconds or until 0° appears in the display.
If the oven temperature was previously adjusted, the
change will be displayed. For example, if the oven
temperature was reduced by 15° the display will show
“-15°”.
Notes:
• For best results when broiling, use a pan designed for
broiling.
• Expect broil times to increase and browning to be slightly
lighter if appliance is installed on a 208-volt circuit.
4. Press the More+ or Less- pad to adjust the temperature.
Each time a pad is pressed, the temperature changes by
5°. The oven temperature can be increased or decreased
by 5° to 35°.
• HI is used for most broiling. Use LO broil when broiling
longer cooking foods. The lower temperature allows
food to cook to the well done stage without excessive
browning.
5. The time of day will automatically reappear in the display.
You do not need to readjust the oven temperature if there
is a power failure or interruption. Broiling and cleaning
temperatures cannot be adjusted.
• To change oven temperature during broiling, press the
Broil pad and then the More+ or Less- pad to switch
between LO and HI broil.
• Broil times may be longer when the lower broiling
temperature is selected.
• Most foods should be turned halfway through broiling
time.
Broiling Chart
RACK
POSITION
APPROX. TIME
FIRST SIDE
APPROX. TIME
SECOND SIDE
FOODS
Beef
Steak, 1” thick,
Medium
Well
6
6
8 minutes
10 minutes
9 minutes
7 - 12 minutes
8 - 14 minutes
6 - 9 minutes
Hamburgers, 3/4” thick, Well
6 or 7
Pork
Bacon
Chops, 1”
Ham Slice
6
6
6
6 - 10 minutes
10 - 11 minutes
5 minutes
(no turning)
12 - 14 minutes
3 - 7 minutes
Poultry
Breast Halves
LO Broil
15 minutes
LO Broil
15 - 25 minutes
4
Seafood
Fish Steaks, buttered, 1” thick
Lobster Tails, 3-4 oz. each
6
5
10 - 15 minutes
7 - 10 minutes
(no turning)
(no turning)
Important: This chart is a suggested guide. The times may vary with the food being cooked.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Shut-Off/
Sabbath Mode
Oven Vent
When the oven is in use the area near the vent may become
hot enough to cause burns. Never block the vent opening.
The oven will automatically turn off after 12 hours if you
accidentally leave it on. This safety feature can be turned off.
The oven vent is located below the backguard vent
shield on your range.
To cancel the 12-hour shut-off and run the
oven continuously for 72 hours:
1. Set the oven to bake (see page 13).
OVEN VENT
LOCATION
Do not place
plastics near the
vent opening as
heat from the vent
could distort or
melt the plastic.
2. Press and hold the Clock pad for five seconds.
• SAb will be displayed and flash for five seconds.
• SAb will then be displayed continuously until turned off
or until the 72-hour time limit is reached.
• BAKE will also be displayed if a bake cycle is in use
while the oven is in Sabbath Mode.
• BAKE is the only function that operates during the
Sabbath Mode. All other functions (Timer, Keep Warm,
Clean, etc.) are locked out during the Sabbath Mode.
Oven Light
The oven light automatically comes on when the
door is opened. When the door is closed, press the
Oven Light switch to turn the oven light on and off.
To cancel Bake when in Sabbath Mode:
Press CANCEL.
• BAKE will turn off in the display.
• No beeps will sound.
Oven Bottom
Protect oven bottom against spillovers, especially acidic or
sugary spills, as they may discolor the porcelain enamel. Use
the correct pan size to avoid spillovers and boilovers. Do not
place utensils or aluminum foil directly on the oven
bottom.
To cancel the Sabbath Mode:
1. Press the Clock pad for five seconds.
OR
2. After 72 hours, the Sabbath Mode will end.
• SAb will flash for 5 seconds.
• The time of day will return to the display.
Oven Racks
CAUTION
Notes:
• Do not attempt to change the rack position when the oven
is hot.
• Sabbath Mode can be turned on at any time with or
without the oven on.
• Do not use the oven for storing food or cookware.
• Sabbath Mode cannot be turned on if the touchpads are
locked out or when the door is locked.
The oven has two racks. All racks are designed with a lock-
stop edge.
• If the oven is baking when Sabbath Mode is set, BAKE
will go out at the end of the baking cycle. There will be
no audible beeps.
To remove:
1. Pull rack straight out until it
stops at the lock-stop
position.
• If the oven light is desired while in Sabbath Mode, it
must be turned on before the Sabbath Mode is started.
2. Lift up on the front of the
rack and pull out.
• When the Sabbath Mode is started, no preheat beep will
sound.
To replace:
1. Place rack on the rack supports in the oven
• All prompts, messages and beeps are deactivated when
Sabbath Mode is active.
2. Tilt the front end up slightly. Slide rack back until it clears
the lock-stop position.
• The automatic door lock does not operate during the
Sabbath Mode.
3. Lower front and slide back into the oven.
• Pressing CANCEL will cancel a Bake cycle, however the
control will stay in the Sabbath Mode.
• If power fails, the oven will power up in Sabbath Mode
with 72 hours remaining and no cycle active.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Never cover an entire rack with aluminum foil or place
foil on the oven bottom. Baking results will be affected
and damage may occur to the oven bottom.
Oven Bottom: Place oven rack on
raised sides of oven bottom. Use for
additional space when cooking large
oven meals.
MULTIPLE RACK COOKING: Two
rack: Use rack positions 2 and 5 or 3
and 6.
Rack Positions
RACK 7 (highest
position): For toasting
bread or broiling thin, non-
fatty foods.
7
6
5
4
3
2
1
Baking Layer Cakes on Two Racks
For best results when baking cakes on two racks, use racks 2
and 4.
RACK 6: Used for most
broiling.
Place the cakes on the rack as shown.
Oven
Bottom
RACK 5: For two rack
baking.
Two Rack Baking
RACK 4: Used for most baked goods on a cookie sheet or
jelly roll pan, fruit pies, or frozen convenience foods. Also use
for broiling chicken pieces.
RACK 3: For casseroles, baking loaves of bread, bundt cakes
or custard pies.
RACK 2: Used for roasting small cuts of meat, frozen pies,
dessert souffles or angel food cake. Also use for two rack
baking.
RACK 1: Used for roasting large cuts of meat and poultry.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
MAYTAG® MAJOR APPLIANCE WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter “Maytag”) will pay for factory
specified parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Maytag designated
service company. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used
in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not apply. Proof of
original purchase date is required to obtain service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is
contrary to published user or operator instructions and/or installation instructions.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by Maytag.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.
6. Any food loss due to refrigerator or freezer product failures.
7. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be
repaired in the home and only in-home service is covered by this warranty.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Maytag servicer is not available.
10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with published installation instructions.
11. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty
is void if the factory applied serial number has been altered or removed from your major appliance.
The cost of repair or replacement under these excluded circumstances shall be borne by the customer.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” you may find
additional help by checking the “Assistance or Service” section or by calling Maytag. In the U.S.A., call 1-800-688-9900. In Canada, call
1-800-807-6777.
9/07
Form No. A/01/08
Part No. 8113P692-60
©2006 Maytag Appliances Sales Co.
All rights reserved.
Litho U.S.A .
Download from Www.Somanuals.com. All Manuals Search And Download.
|