Front-Loading Automatic Washer
OVERALL DIMENSIONS
PRODUCT MODEL NUMBERS
Washer dimensions
MHW6000X, MHW7000X,
MHW9000X, MHW9000Y
27"
(686 mm)
51"
(1295 mm)
Custom under counter installation:
Electrical: A 120 volt, 60 Hz., AC only, 15- or 20-amp,
fused electrical supply is required. A time-delay fuse or
circuit breaker is recommended. It is recommended that
a separate circuit serving only this appliance
be provided.
38"
(965 mm)
39" min.
(990 mm)
1
/
2" - 1"
(13 mm - 25 mm)
Drain System Options
1"
311/2
(800 mm)
"
(25 mm)
Drain system can be installed using a floor drain, wall
standpipe, floor standpipe, or laundry tub. Select
method you need.
1"
(25 mm)
Recessed area or closet installation (washer only):
IMPORTANT: To avoid siphoning, 4.5" (113 mm) of
drain hose should be inside standpipe or below the top
of wash tub. Always secure drain hose with cable tie
All dimensions show recommended spacing allowed, except for closet door ventilation
openings which are the minimum required.
For each arrangement, consider
allowing more space for ease
of installation and servicing,
Floor standpipe drain system
3"
(76 mm)
and spacing for companion
48 in.2
appliances and clearances for
walls, doors, and floor moldings.
Space must be large enough to
allow door to fully open.
(310 cm2)
41/2"
(113 mm)
Add spacing of 1" (25 mm) on all
sides of washer to reduce
noise transfer. If a closet door
or louvered door is installed, top
and bottom air openings in door
are required.
24 in.2
(155 cm2)
Minimum diameter for a standpipe drain: 2" (51 mm).
Minimum carry-away capacity: 17 gal. (64 L) per minute.
A / " (6 mm) diameter to 1" (25 mm) diameter Top of
standpipe must be at least 30" (762 mm) high; install no
higher than 96" (2.44 m) from bottom of washer. If you
must install higher than 96" (2.44 m), you will need a sump
pump system.
4"
3"
(76 mm)
(102 mm)
1
4
1"
(25 mm)
1"
(25 mm)
Recessed area or closet installation
(stacked washer and dryer):
Custom cabinet installation:
6"
(152 mm)
Wall standpipe drain system
7"
(178 mm)
3"
(76 mm)
48 in.2
(310 cm2)
41/2"
(113 mm)
14"
(356 mm)
771/2"
(1969 mm)
24 in.2
(155 cm2)
Floor drain system
4"
5"
3"
(76 mm)
(102 mm)
(127 mm)
1"
(25 mm)
1"
(25 mm)
1"
(25 mm)
1"
(25 mm)
Laundry tub drain system
Floor drain system requires additional parts. Minimum
siphon break: 28" (711 mm) from bottom of washer.
Minimum capacity: 20 gal. (76 L).
Top of laundry tub must be at least
30" (762 mm) above floor; install no
higher than 96" (2.44 m) from bottom
of washer.
41/2"
(113 mm)
min.
30"
(762 mm)
Ref. W10254447B
02/2011
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|