MDG7 5 PNH an d MDG7 5 MNV
(1 ,0 0 0 CFM/ Ph ase 7 wit h S.A.F.E.)
In st allat ion Man u al
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette notice
pour réduire au minimum le risque d’incendie
ou d’explosion ou pour éviter tout dommage
matériel, toute blessure ou la mort.
WARNING: For your safety the information in
this manual must be followed to minimize the
risk of fire or explosion or to prevent property
damage, personal injury or death.
— Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquides inflammables à
proximité de cet appareil ou de tout autre
appareil.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELLGAS:
— QUE FAIRE SIVOUS SENTEZ UNE ODEUR
DE GAZ:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Clear the room, building or area of all
occupants.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• Ne pas tenter d’allumer d’appareils.
• Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment.
• Évacuez la pièce, le bâtiment ou la zone.
• Appelez immédiatement votre fournisseur
de gaz depuis un voisin. Suivez les
instructions du fournisseur.
• If you cannot reach your gas supplier, call
the fire department.
• Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.
— Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
— L’installation et l’entretien doivent être assurés par
un installateur ou un service d’entretien qualifié
ou par le fournisseur de gaz.
RETAIN THESE INSTRUCTIONS INASAFE
PLACE FOR FUTURE REFERENCE
122002JEV/mcronan
Part No. 113394
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
YOU MUSTDISCONNECTAND LOCK OUTTHE ELECTRIC SUPPLYANDTHE GAS
SUPPLY BEFORE ANY COVERS OR GUARDS ARE REMOVED FROM THE
MACHINETOALLOWACCESS FOR CLEANING,ADJUSTING, INSTALLATION, OR
TESTING OF ANY EQUIPMENT PER OSHA (Occupational Safety and Health
Administration) STANDARDS.
«Attention: Au moment de l’entretien des
commandes, étiquetez tous les fils avant de
les débrancher. Des erreurs de câblage
peuvent entraîner un fonctionnement
inadéquat et dangereux.»
“Caution: Label all wires prior to
disconnection when servicing controls. Wiring
errors can cause improper operation.”
CAUTION
DRYERS SHOULD NEVER BE LEFT UNATTENDEDWHILE IN OPERATION.
WARNING
CHILDREN SHOULD NOTBEALLOWED TO PLAYON OR NEAR THE DRYER(S).
CHILDREN SHOULD BE SUPERVISED IFNEAR DRYERS IN OPERATION.
FORYOUR SAFETY
DO NOT DRYMOPHEADS INTHE DRYER.
DO NOT USE DRYER INTHE PRESENCE OF DRYCLEANING FUMES.
WARNING
UNDER NO CIRCUMSTANCES should the dryer door switches, lint drawer switch,
or heat safety circuit ever be disabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
The dryer must never be operated with any of the back guards, outer tops, or service
panels removed. PERSONALINJURYOR FIRE COULD RESULT.
WARNING
DRYER MUST NEVER BE OPERATED WITHOUTTHE LINT FILTER/SCREEN IN
PLACE, EVEN IFAN EXTERNALLINT COLLECTION SYSTEM IS USED.
IMPORTANT
PLEASE OBSERVEALLSAFETYPRECAUTIONS displayed on the equipment and/or
specified in the installation manual included with the dryer.
Dryer must not be installed or stored in an area where it will be exposed to water or weather.
The wiring diagram for the dryer is located in the front electrical control box area.
IMPORTANT
Dryer must be installed in a location/environment, which the ambient temperature
remains between 40° F (4.44° C) and 130° F (54.44° C).
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta ble of Con t en t s
SECTION I
SAFETY PRECAUTIONS ........................................................................................ 3
SECTION II
SPECIFICATIONS..................................................................................................... 5
A. Specifications ............................................................................................................................. 5
B. Component Identification ............................................................................................................ 7
SECTION III
INSTALLATION PROCEDURES ........................................................................... 9
A. Location Requirements ............................................................................................................... 9
B. Unpacking/Setting Up ............................................................................................................... 10
C. Dryer Enclosure Requirements .................................................................................................. 11
D. FreshAir Supply Requirements ................................................................................................. 12
E. Exhaust Requirements ............................................................................................................... 13
F. Electrical Information ................................................................................................................ 18
G. Gas Information ........................................................................................................................ 22
H. Preparation For Operation/Start-Up ......................................................................................... 26
I. PreoperationalTests ................................................................................................................. 27
J. Preoperational Instructions ........................................................................................................ 29
K. Shutdown Instructions ............................................................................................................... 30
SECTION IV
SERVICE/PARTS INFORMATION ...................................................................... 31
A. Service ..................................................................................................................................... 31
B. Parts ........................................................................................................................................ 31
SECTION V
ROUTINE MAINTENANCE .................................................................................. 32
A. Cleaning ................................................................................................................................... 32
B. Adjustments ............................................................................................................................. 33
C. Lubrication ............................................................................................................................... 33
D. Lint Drawer Removal ................................................................................................................ 34
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION VI
DATA LABEL INFORMATION ............................................................................. 35
SECTION VII
PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT
COMPONENTS........................................................................................................ 36
SECTION VIII
MANUAL RESET BURNER HI-LIMIT INSTRUCTIONS ............................... 38
A. Phase 7......................................................................................................................................38
B. DualTimer ................................................................................................................................ 38
SECTION IX
SENSOR ACTIVATED FIRE EXTINGUISHING (S.A.F.E.) SYSTEM............39
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION I
SAFETY PRECAUTIONS
WARNING: For your safety, the information in this manual must be followed to minimize the risk of
fire or explosion or to prevent property damage, personal injury, or loss of life.
WARNING: The dryer must never be operated with any of the back guards, outer tops, or
service panels removed. PERSONALINJURY OR FIRE COULD RESULT.
1. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
2. Purchaser and user should consult the local gas supplier for proper instructions to be followed in the event
the user smells gas. The instructions should be posted in a prominent location.
3. WHATTO DO IFYOU SMELLGAS:
a. DO NOT try to light any appliance.
b. DO NOT touch any electrical switch.
c. DO NOT use any phone in your building.
d. Clear the room, building, or area of ALL occupants.
e. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
f. If you cannot reach your gas supplier, call the fire department.
4. Installation and service must be performed by a qualified installer, service agency, or gas supplier.
5. Dryers must be exhausted to the outdoors.
6. Although Maytag produces a very versatile dryer, there are some articles that, due to fabric composition or
cleaning method, should not be dried in it.
WARNING: Dry only water washed fabrics. DO NOT dry articles spotted or washed in dry
cleaning solvents, a combustible detergent, or “all purpose” cleaner.
EXPLOSION COULD RESULT.
WARNING: DO NOT dry rags or articles coated or contaminated with gasoline, kerosene, oil, paint,
or wax.
EXPLOSION COULD RESULT.
WARNING: DO NOT dry mop heads. Contamination by wax or flammable solvents will create a
fire hazard.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, or
similarly textured rubber materials. Drying in a heated basket (tumbler) may damage
plastics or rubber and may be a fire hazard.
7. A program should be established for the inspection and cleaning of lint in the burner area, exhaust ductwork,
and area around the back of the dryer. The frequency of inspection and cleaning can best be determined
from experience at each location.
WARNING: The collection of lint in the burner area and exhaust ductwork can create a potential fire
hazard.
8. For personal safety, the dryer must be electrically grounded in accordance with local codes and/or the
National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in Canada, the Canadian Electrical
Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.
NOTE: Failure to electrically ground the dryer properly will VOIDTHE WARRANTY.
9. UNDER NO CIRCUMSTANCES should the dryer door switches, lint drawer switch, or heat safety
circuit ever be disabled.
WARNING: PERSONALINJURYOR FIRE COULD RESULT SHOULD THE DRYER
DOOR SWITCHES, LINT DRAWER SWITCH, OR HEAT SAFETYCIRCUIT
EVER BE DISABLED.
10. This dryer is not to be used in the presence of dry cleaning solvents or fumes.
11. Remove articles from the dryer as soon as the drying cycle has been completed.
WARNING: Articles left in the dryer after the drying and cooling cycles have been completed can
create a fire hazard.
12. READ AND FOLLOW ALL CAUTION AND DIRECTION LABELS ATTACHED TO THE
DRYER.
13. For safety, proper operation, and optimum performance, the dryer must not be operated with a load less
than sixty-six percent (66%) 50 lbs (22.7 kg) of its rated capacity.
WARNING: YOU MUST DISCONNECTAND LOCK OUTTHE ELECTRIC SUPPLY
AND THE GAS SUPPLY BEFOREANYCOVERS OR GUARDSARE
REMOVED FROM THE MACHINE TOALLOWACCESS FOR CLEANING,
ADJUSTING, INSTALLATION, OR TESTINGOFANYEQUIPMENT PER
OSHA (Occupational Safety and HealthAdministration) STANDARDS.
IMPORTANT: Dryer must be installed in a location/environment, which the ambient
temperature remains between 40º F (4.44º C) and 130º F (54.44º C).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION II
SPECIFICATIONS
A. SPECIFICATIONS
34 kg
94 cm
MAXIMUM CAPACITY (DRY WEIGHT)
BASKET (TUMBLER) DIAMETER
BASKET (TUMBLER) DEPTH
BASKET (TUMBLER) MOTOR
DOOR OPENING (DIAMETER)
BASKET (TUMBLER) VOLUME
EXHAUST CONNECTION (DIAMETER)
AIRFLOW
75 lbs
37”
91.5 cm
36”
0.745 k
W
1
hp*
54.61 cm
0.634 cu m
20.3 cm
21-1/2”
22.4 cu ft
8”
28.3 cmm
1000 cfm
DRYERS PER 20’/40’ CONTAINER
DRYERS PER 48’/53’ TRUCK
S.A.F.E. WATER CONNECTION
VOLTAGE AVAILABLE
10/20
24/26
3/4-11.5 NH
120-460v 1ø-3ø 3, 4w 50/60 Hz
327 kg
349.7 kg
APPROX. WEIGHT (UNCRATED)
APPROX. WEIGHT (CRATED)
HEAT INPUT
721 lbs
771 lbs
44,100 kcal/hr
175,000 Btu/hr
INLET PIPE CONNECTION
Shaded areas are stated in metric equivalents
3/4” F.N.P.T.**
2/5/04
*
ALL reversing dryers are supplied with two (2) 3-phase (3ø) motors standard: a 1/2 hp (0.37 kW) blower motor and a 1/2 hp (0.37 kW) drive motor.
**
Size of piping to dryer varies with installation conditions. Contact factory for assistance.
NOTE: The manufacturer reserves the right to make changes in specifications at any time without
notice or obligation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications – Gas
NOTE: Manufacturer reserves the right to make changes in specifications at any time without notice or
obligation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
B. COMPONENT IDENTIFICATION
1. Dryer Front View
Illus. No.
Description
1
2
3
4
5
Controls
Control (top access) Door Assembly
Main Door Assembly
Lint Compartment Area (lint screen located behind lint door or left sidewall)
Data Label and Installation Label
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Dryer Rear View
Illus. No.
Description
1
2
3
4
5
6
7
8
Heating Unit
Electric Service Relay Box
Basket (tumbler) Bearing Mount Assembly
Idler Bearing MountAssembly
Blower Motor Assembly (for reversing models only)
Leveling Legs (rear)
Basket (tumbler) (drive) Motor Assembly
Dryer Exhaust
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION III
INSTALLATION PROCEDURES
Installation should be performed by competent technicians in accordance with local and state codes. In the
absence of these codes, the installation must conform to applicableAmerican National Standards:ANSI Z223.1-
LATESTEDITION(NationalFuelGasCode)orAN SI/NFPA NO. 70-LATEST EDITION (National Electrical
Code) or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91
(Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST EDITION (for General
InstallationandGasPlumbing)orCanadianElectricalCodesParts1&2CSAC22.1-1990orLA TEST EDITION
(for Electrical Connections).
A. LOCATION REQUIREMENTS
Before installing the dryer, be sure the location conforms to local codes and ordinances. In the absence of such
codes or ordinances the location must conform with the National Fuel Gas Code ANSI.Z223.1 LATEST
EDITION, or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-
M91 (Natural Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General Installation and
Gas Plumbing).
1. The dryer must be installed on a sound level floor capable of supporting its weight. Carpeting must be
removed from the floor area that the dryer is to rest on.
IMPORTANT: “The dryer must be installed on noncombustible floors only.”
2. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.
3. The dryer is for use in noncombustible locations.
4. Provisions for adequate air supply must be provided as noted in this manual (refer to Fresh Air Supply
Requirements in Section D).
5. Clearance provisions must be made from noncombustible construction as noted in this manual (refer to
Dryer Enclosure Requirements in Section C).
6. Provisions must be made for adequate clearances for servicing and for operation as noted in this manual
(refer to Dryer Enclosure Requirements in Section C).
7. Dryer must be exhausted to the outdoors as noted in this manual (refer to Exhaust Requirements in
Section E).
8. Dryer must be located in an area where correct exhaust venting can be achieved as noted in this manual
(refer to Exhaust Requirements in Section E).
IMPORTANT: Dryer should be located where a minimum amount of exhaust duct will be necessary.
9. The dryer must be installed with a proper exhaust duct connection to the outside.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10. The dryer must be installed with provisions for adequate combustion and make-up air supply.
CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors. Every 6
months, inspect the exhaust ducting and remove any lint buildup.
IMPORTANT: Dryer must be installed in a location/environment, which the ambient
temperature remains between 40º F (4.44º C) and 130º F (54.44º C).
B. UNPACKING/SETTING UP
Remove protective shipping material (i.e., plastic wrap and/or optional shipping box) from dryer.
IMPORTANT: Dryer must be transported and handled in an upright position at ALL times.
The dryer can be moved to its final location while still attached to the skid or with the skid removed. To unskid
the dryer, locate and remove the four (4) bolts securing the base of the dryer to the wooden skid. Two (2) are
at the rear base (remove the back panel for access), and two (2) are located in the bottom of the lint chamber.
To remove the two (2) bolts located in the lint chamber area, remove the lint door.
Leveling Dryer
The dryer is equipped with four (4) leveling legs, one (1) at each corner of the base. Two (2) are located at the
rear of the dryer base, and two (2) are located in the lint chamber (coop). To increase bearing life and improve
efficiency, the dryer should be tilted slightly to the rear.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
C. DRYER ENCLOSURE REQUIREMENTS
Bulkheads and partitions should be made of noncombustible materials and must be located a minimum of
12-inches (30.48 cm), 18-inches (45.72 cm) or more is recommended for ease of installation, maintenance, and
service above the dryer’s outer top, except along the front of the dryer which may be partially closed in if
desired. The clearance between the bulkhead header and the dryer must be a minimum of 4-inches (10.16 cm)
and must not extend more than 4-inches (10.16 cm) to the rear of the front. The bulkhead facing must not be
closed in ALL the way to the top of the dryer. A 1-inch (2.54 cm) clearance is required.
NOTE: Allowances must be made for the opening of the control door.
Dryers may be positioned sidewall to sidewall. However, a 1/16” (1.57 mm) minimum allowance must be made
for the opening and closing of the control door and the lint door. It is suggested that the dryer be positioned about
2 feet (0.61 meters) away from the nearest obstruction for ease of installation, maintenance, and service (to be
measured from the back guard). Refer to the illustration above for details.
NOTE: Air considerations are important for proper and efficient operation.
IMPORTANT: Even though a minimum of only 12-inches (30.48 cm) is required, 18-inches
(45.72 cm) or more is suggested. The additional clearance is advantageous for
ease of installation and service.
IMPORTANT: When fire sprinkler systems are located above the dryers, a minimum of 18-inches
(45.72 cm) above the dryer console (module) is required. Dryers may be positioned
sidewall to sidewall however, a 1/16” (1.57 mm) minimum allowance is required
between dryers (or wall) for ease of installation and maintenance. Allowances must
be made for the opening and closing of the control door and the lint door.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
D. FRESH AIR SUPPLY REQUIREMENTS
When the dryer is operating, it draws in room air, heats it, passes this air through the basket (tumbler), and
exhausts it out of the building. Therefore, the room air must be continually replenished from the outdoors. If the
make-up air is inadequate, drying time and drying efficiency will be adversely affected. Ignition problems and
sail switch “fluttering” problems may result, as well as premature motor failure from overheating.
Air supply (make-up air) must be given careful consideration to ensure proper performance of each dryer. An
unrestricted source of air is necessary for each dryer. An airflow of 1,000 cfm (cubic feet per minute [28.3
cmm] [cubic meters per minute]) must be supplied to each dryer. As a general rule, an unrestricted air entrance
from the outdoors (atmosphere) of a minimum of 1-1/2 square feet (0.14 square meters) is required for each
dryer. The dryer must be installed with provisions for adequate combustion and make-up air supply.
IMPORTANT: Make-up air openings should not be located in an area directly near where exhaust
vents exit the building.
To compensate for the use of registers or louvers used over the openings, this make-up air must be increased by
approximately thirty-three percent (33%). Make-up air openings should not be located in an area directly near
where exhaust vents exit the building.
It is not necessary to have a separate make-up air opening for each dryer. Common make-up air openings are
acceptable. However, they must be set up in such a manner that the make-up air is distributed equally to ALL
the dryers.
EXAMPLE: For a bank of four (4) dryers, two (2) unrestricted openings measuring 2 feet by 1-1/2 feet (0.61
meters by 0.46 meters) are acceptable.
Allowances must be made for remote or constricting passageways or where dryers are located at excessive
altitudes or predominantly low pressure areas.
IMPORTANT: Make-up air must be provided from a source free of dry cleaning solvent fumes.
Make-up air that is contaminated by dry cleaning solvent fumes will result in
irreparable damage to the motors and other dryer components.
NOTE: Component failure due to dry cleaning solvent fumes willVOIDTHEWARRANTY.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
E. EXHAUST REQUIREMENTS
1. General Exhaust Ductwork Information
Exhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwork
will create excessive back pressure which results in slow drying, increased use of energy, overheating
of the dryer, and shutdown of the burner by the airflow (sail) switches, burner hi-limits, or basket (tumbler)
hi-heat thermostats. The dryer must be installed with a proper exhaust duct connection to the outside.
CAUTION:This dryer produces combustible lint and must be exhausted to the outdoors.
CAUTION: IMPROPERLY SIZED OR INSTALLED EXHAUST DUCTWORK CAN
CREATE APOTENTIAL FIRE HAZARD.
The ductwork should be laid out in such a way that the ductwork travels as directly as possible to the
outdoors with as few turns as possible. Single or independent dryer venting is recommended.
IMPORTANT: It is recommended that exhaust or booster fans not be used in the exhaust ductwork
system.
Horizontal Venting:
When single dryer venting is used, the length of ductwork from the dryer to the outside exhaust outlet
must not exceed 25 feet (7.62 meters). The minimum diameter of this ductwork must be at least
8-inches (20.32 cm). In the case of multiple (common) dryer venting, the distance from the last dryer to the
outside exhaust outlet must not exceed 15 feet (4.57 meters). The shape of the ductwork is not critical
as long as the minimum cross-sectional area is provided. It is suggested that the use of 90° turns be
avoided; use 30° and/or 45° angles instead. The radius of the elbows should preferably be 1-1/2 times
the diameter of the duct. Including basket (tumbler)/dryer elbow connections or elbows used for outside
protection from the weather, no more than two (2) elbows should be used in the exhaust duct run. If more
than two (2) elbows are used, the cross-sectional area of the ductwork must be increased. ALL ductwork
should be smooth inside with no projections from sheet metal screws or other obstructions, which will
collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be connected.
ALL ductwork joints must be taped to prevent moisture and lint from escaping into the building. Inspection
doors should be installed at strategic points in the exhaust ductwork for periodic inspection and cleaning of
lint from the ductwork.
Vertical Venting:
When single dryer venting is used, the length of the ductwork from the dryer to the outside exhaust outlet
must not exceed 15 feet (4.57 meters). The minimum diameter of this ductwork must be at least
8-inches (20.32 cm). In the case of multiple (common) dryer venting, the distance from the last dryer to the
outside exhaust outlet must not exceed 15 feet (4.57 meters). The shape of the ductwork is not so critical
as long as the minimum cross-sectional area is provided. It is suggested that the use of 90º turns be
avoided; use 30º and/or 45º bends instead. The radius of the elbows should preferably be 1-1/2 times the
diameter of the duct. ALL ductwork should be smooth inside with no projections from sheet metal
screws or other obstructions, which will collect lint. When adding ducts, the duct to be added should
overlap the duct to which it is to be connected. ALL ductwork joints must be taped to prevent moisture
and lint from escaping into the building. Inspection doors should be installed at strategic points in the
exhaust ductwork for periodic inspection and cleaning of lint from the ductwork.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Exhaust back pressure measured by a manometer in the exhaust duct must be no less
than 0 and must not exceed 0.3 inches (0.74 mb) of water column (W.C.).
NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible
materials, the opening must be 2-inches (5.08 cm) larger than the duct (all the way around).
The duct must be centered within this opening.
NOTE: As per the National Fuel Gas Code, “Exhaust ducts for type 2 clothes dryers shall be
constructed of sheet metal or other noncombustible material. Such ducts shall be equivalent in
strength and corrosion resistance to ducts made of galvanized sheet steel not less than
0.0195-inches (26 gauge [0.05 mm]) thick.”
Outside Ductwork Protection
To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward
should be installed where the exhaust exits the building. If the ductwork travels vertically up
through the roof, it should be protected from the weather by using a 180° turn to point the opening
downward. In either case, allow at least twice the diameter of the duct between the duct opening and the
nearest obstruction.
IMPORTANT: DO NOT use screens, louvers, or caps on the outside opening of the exhaust
ductwork.
2. Single Dryer Venting
When possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust duct should
be laid out in such a way that the ductwork travels as directly as possible to the outdoors with as few turns
as possible. It is suggested that the use of 90° turns in the ducting be avoided; use 30° and/or 45° angles
instead. The shape of the exhaust ductwork is not critical as long as the minimum cross section area is
provided.
IMPORTANT: Exhaust back pressure measured by a manometer in the exhaust duct must be no less
than 0 and must not exceed 0.3 inches (0.74 mb) of water column.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: For extended ductwork runs, the cross section area of the ductwork can only be
increased to an extent. When the ductwork approaches the maximum limits noted in
this manual, a professional heating, ventilating, and air- conditioning (HVAC) firm
should be consulted for proper venting information.
ALL ductwork should be smooth inside with no projections from sheet metal screws or other obstructions,
which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to
be connected. ALL ductwork joints must be taped to prevent moisture and lint from escaping into the
building. Inspection doors should be installed at strategic points in the exhaust ductwork for periodic
inspection and cleaning of lint from the ductwork.
NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible
materials, the opening must be 2-inches (5.08 cm) larger than the duct (all the way around).
The duct must be centered within this opening.
Outside Ductwork Protection
To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward
should be installed where the exhaust exits the building. If the ductwork travels vertically up through
the roof, it should be protected from the weather by using a 180° turn to point the opening downward.
In either case, allow at least twice the diameter of the duct between the duct opening and the nearest
obstruction.
IMPORTANT: DO NOT use screens, louvers, or caps on the outside opening of the exhaust
ductwork.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Multiple (Common) Dryer Venting
IMPORTANT: For extended ductwork runs, the cross section area of the ductwork can only be
increased to an extent. When the ductwork approaches the maximum limits noted in
this manual, a professional heating, ventilating, and air-conditioning (HVAC) firm
should be consulted for proper venting information.
ALL ductwork should be smooth inside with no projections from sheet metal screws or other obstructions,
which will collect lint. When adding ducts, the duct to be added should overlap the duct to which it is to be
connected. ALL ductwork joints must be taped to prevent moisture and lint from escaping into the
building. Inspection doors should be installed at strategic points in the exhaust ductwork for periodic
inspection and cleaning of lint from the ductwork.
NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible
materials, the opening must be 2-inches (5.08 cm) larger than the duct (all the way around).
The duct must be centered within this opening.
Outside Ductwork Protection
To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward
should be installed where the exhaust exits the building. If the ductwork travels vertically up
through the roof, it should be protected from the weather by using a 180° turn to point the opening
downward. In either case, allow at least twice the diameter of the duct between the duct opening and the
nearest obstruction.
IMPORTANT: DO NOT use screens, louvers, or caps on the outside opening of the exhaust
ductwork.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANTVENTINGREMINDERS
1. Ductwork size and installation should be done by a qualified professional.
2. The dryer must be exhausted to the outdoors.
3. Ductwork should be routed as short as possible to the outdoors with as few elbows as possible.
4. Avoid 90° turns, use 30° or 45° turns instead.
5. For single dryer venting, the size of the ductwork must be a minimum of 8-inches (20.32 cm) for short runs
(refer to the illustration on page 15). For longer runs, the diameter must be increased.
6. The inside of the ductwork should be as smooth as possible with no projections from sheet metal screws.
7. Ducts added should overlap the duct to which it is to be connected.
8. ALL ducts should be taped to prevent moisture and lint from escaping into the building.
9. Inspection (cleaning) doors should be installed throughout strategic points in the ductwork for periodic
inspection and cleaning.
10. Whenever the ductwork passes through combustible materials, the opening must be 2-inches (5.08 cm)
larger than the duct (all the way around). The duct must be centered within this opening.
11. The outside of the ductwork must be protectedfromtheweather. A90°elbow must be used for horizontal
run and when vertically through a roof by using a 180° turn to point the opening downward. The distance
between the exhaust duct and the nearest obstruction (i.e., roof or ground) must be twice the diameter of
the duct.
12. DO NOT use screens, louvers, or caps on the outside opening of the exhaust ductwork.
13. Exhaust back pressure measured by a manometer at the dryer’s exhaust duct area must be no less than 0
and must not exceed 0.3 inches (0.74 mb) of water column (W.C.).
14. Exhaust ductwork outlets should not be located in an area directly where make-up air openings are
located.
WARNING: DRYER MUST NEVER BE OPERATED WITHOUT THE LINT FILTER/
SCREEN IN PLACE, EVEN IFAN EXTERNALLINT COLLECTION
SYSTEM IS USED.
15. It is recommended that exhaust or booster fans not be used in the exhaust ductwork system.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
F. ELECTRICAL INFORMATION
1. Electrical Requirements
ALL electrical connections must be made by a properly licensed and competent electrician. This
is to ensure that the electrical installation is adequate and conforms to local and state regulations or codes.
In the absence of such codes, ALL electrical connections, materials, and workmanship must conform to
the applicable requirements of the National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in
Canada, the Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.
IMPORTANT: Failure to comply with these codes or ordinances, and/or the requirements stipulated
in this manual can result in personal injury or component failure.
NOTE: Component failure due to improper installation will VOID THEWARRANTY.
Each dryer should be connected to an independently protected branch circuit. The dryer must be connected
with copper wire only. DO NOT use aluminum wire; it can create a fire hazard. The copper conductor
wire/cable must be of proper ampacity and insulation in accordance with electric codes for making ALL
service connections.
NOTE: The use of aluminum wire willVOIDTHEWARRANTY.
IMPORTANT: Aseparate protected circuit must be provided to each dryer.
NOTE: An individual ground circuit must be provided to each dryer, do not daisy chain.
IMPORTANT: The dryer must be connected to the electric supply shown on the data label. In the
case of 208 VAC or 240 VAC, the supply voltage must match the electric service
specifications of the data label exactly.
IMPORTANT: The wire size must be properly sized to handle the related current.
WARNING: 208 VAC AND 240 VACARE NOT THE SAME. Any damage done to dryer
components due to improper voltage connections will automatically VOID THE
WARRANTY.
NOTE: Component failure due to improper voltage application willVOIDTHEWARRANTY.
NOTE: The manufacturer reserves the right to make changes in specifications at any time without
notice or obligation.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Electrical Service Specifications
IMPORTANT: Figures shown are for non-reversing models only. For reversing models contact the
factory.
*$6
(/(&75,&$/ꢀ6(59,&(ꢀ63(&,),&$7,216ꢀꢁ3(5ꢀ'5<(5ꢂ
$3352;ꢀ
$03ꢁ'5$:
)86,1*
6(59,&(
92/7$*(
:,5(
6(59,&(
0,1,080
:,5(ꢁ6,=(
&,5&8,7
%5($.(5
3+$6(
ꢃꢄꢅ
ꢄꢅꢉ
ꢃ¡
ꢃ¡
ꢃ¡
ꢆ¡
ꢆ¡
ꢆ¡
ꢆ¡
ꢆ¡
ꢆ¡
ꢄ
ꢄ
ꢃꢆꢇꢅ
ꢊꢇꢋ
ꢊꢇꢅ
ꢍꢇꢊ
ꢍꢇꢎꢌꢇꢋ
±
±
±
ꢄꢅ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢄꢅ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢃꢌ
ꢈ
ꢈ
ꢈ
ꢈ
ꢈ
ꢈ
ꢈ
ꢈ
ꢈ
ꢄꢍꢅ
ꢄ
ꢊꢇꢉ
±
ꢄꢅꢉ
ꢆ
ꢄꢍꢅ
ꢆ
ꢆꢉꢅ
ꢀꢀꢀꢍꢈꢈ
ꢀꢀꢀꢍꢈꢈ
ꢀꢀꢀꢍꢈꢈ
ꢆ
ꢄꢇꢎ
ꢆꢇꢄ
ꢆꢇꢃ
±
ꢍꢅꢅ
±
ꢍꢃꢋ
±
ꢍꢋꢅꢏꢍꢉꢅ
ꢄꢇꢉ
*
AWG Stranded Wire Type...size wire as per National Electrical Code or local codes.
2/9/04
** 3-Wire is available.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Grounding
A ground (earth) connection must be provided and installed in accordance with state and local codes. In
the absence of these codes, grounding must conform to applicable requirements of the National Electrical
Code ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the installation must conform to applicable
Canada Standards: Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION. The
ground connection may be to a proven earth ground at the location service panel.
For added personal safety, when possible, it is suggested that a separate ground wire (no. 18 minimum) be
connected from the ground connection of the dryer to a grounded cold water pipe. DO NOT ground to a
gas pipe or hot water pipe. The grounded cold water pipe must have metal-to-metal connection ALL the
way to the electrical ground. If there are any nonmetallic interruptions, such as, a meter, pump, plastic,
rubber, or other insulating connectors, they must be jumped out with no. 4 copper wire and securely
clamped to bare metal at both ends.
IMPORTANT: For personal safety and proper operation, the dryer must be grounded.
Provisions are made for ground connection in each dryer at the electrical service connection area.
4. Electrical Connections
A wiring diagram is located inside the control box for connection data.
If local codes permit, power to the dryer can be made by the use of a flexible U.L. listed power cord/pigtail
(wire size must conform to rating of dryer), or the dryer can be hard wired directly to the service breaker
panel. In both cases, a strain relief must be installed where the wiring enters the dryer.
IMPORTANT: Aseparate protected circuit must be provided to each dryer.
a. Single-Phase (1ø) Wiring Connections/Hookup
The electrical input connections on ALL
single-phase (1ø) gas dryers are made into
the rear service box located at the upper left
area of the dryer.
6LQJOHꢀ3KDVHꢁ(OHFWULFDOꢁ/HDGꢁ&RQQHFWLRQV
:KLWHꢁRUꢁ5HG
%ODFN
ꢂ
3RVLWLYH
*UHHQ
ꢂ
*URXQG
ꢂ
1HXWUDO
RUꢁ/ꢃ
20
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR 110VAPPLICATIONS
FOR 208-240VAPPLICATIONS
A ground lug is provided in the rear electrical box to connect your service ground.
b. 3-Phase (3ø) Wiring Connections/Hookup
The electrical connections on ALL 3-phase (3ø) dryers are made into the rear service box located at
the upper left area of the dryer. The electrical connections are made at the power distribution block
located in the service box. The ground connection is made to the copper lug, also provided in this box.
To gain access, the service box cover must be removed.
The neutral will only be used on 4-wire service. This is typical for 380-416V, 50 Hz.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
G. GAS INFORMATION
It is your responsibility to have ALL plumbing connections made by a qualified professional to ensure that the
gas plumbing installation is adequate and conforms to local and state regulations or codes. In the absence of
such codes, ALL plumbing connections, materials, and workmanship must conform to the applicable requirements
of the National Fuel Gas Code ANSI Z223.1-LATEST EDITION, or in Canada, the Canadian Installation
Codes CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST
EDITION.
IMPORTANT: Failure to comply with these codes or ordinances, and/or the requirements stipulated
in this manual, can result in personal injury and improper operation of the dryer.
The dryer and its individual shutoff valves must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The dryer must be isolated
from the gas supply piping system by closing its individual manual shutoff valve during any pressure test of the
gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa).
IMPORTANT: Failure to isolate or disconnect dryer from supply as noted can cause irreparable
damage to the gas valve, which willVOID THEWARRANTY.
WARNING: FIRE OR EXPLOSION COULD RESULT DUE TO FAILURE OF
ISOLATINGOR DISCONNECTINGTHE GAS SUPPLYAS NOTED.
1. Gas Supply
The gas dryer installation must meet the American National Standard...National Fuel Gas Code ANSI
Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes CAN/CGA-B149.1 M91 (Natural
Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION, as well as local codes and ordinances
and must be done by a qualified professional.
NOTE: Undersized gas piping will result in ignition problems, slow drying, increased use of energy, and
can create a safety hazard.
The dryer must be connected to the type of heat/gas indicated on the dryer data label. If this information
does not agree with the type of gas available, DO NOT operate the dryer. Contact the Maytag dealer
who sold the dryer or contact the Maytag Co.
IMPORTANT: Any burner changes or conversions must be made by a qualified professional.
The input ratings shown on the dryer data label are for elevations up to 2,000 feet (610 meters), unless
elevation requirements of over 2,000 feet (610 meters) were specified at the time the dryer order was
placed with the factory. The adjustment or conversion of dryers in the field for elevations over 2,000 feet
(610 meters) is made by changing each burner orifice. If this conversion is necessary, contact the
Maytag dealer who sold the dryer or contact the Maytag Co.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Technical Gas Data
a. Gas Specifications
7<3(ꢀ2)ꢀ*$6
I6UVS6G
"ꢃ$ꢀvpur†ꢀXꢃ8ꢃ
%ꢃꢄꢀꢅꢀ !ꢃꢄꢀvpur†ꢀXꢃ8ꢃ
GDRVD9ꢀQSPQ6I@
ꢁꢂꢃꢀPE
ꢄꢅꢂꢆꢀPE
ꢄꢃꢂꢇꢀPE
ꢀꢀHhvs‚yqꢀQꢁr††ˆꢁrꢂ
ꢄꢃ$ꢀvpur†ꢀXꢃ8ꢃ
ꢃꢄꢀvpur†ꢀXꢃ8ꢃ
ꢆꢇꢂꢈꢄꢀꢉꢀꢄꢈꢂꢈꢀPE
ꢀꢀDꢅGvrꢀQꢁr††ˆꢁr
Shaded areas are stated in metric equivalents
*
Measured at outlet side of gas valve pressure tap when gas valve is on.
b. Gas Connections
Inlet connection------------------- 3/4” N.P.T.
Inlet supply size------------------- 3/4” Diameter Pipe (minimum)
Btu/hr input (per dryer)---------- 175,000 (44,100 kcal/hr)
1) Natural Gas
Regulation is controlled by the dryer’s gas valve’s internal regulator. Incoming supply pressure
must be consistent between a minimum of 6.0 inches (14.92 mb) and a maximum of 12.0 inches
(29.9 mb) water column (W.C.) pressure.
2) Liquid Propane (L.P.) Gas
Dryers made for use with L.P. gas have the gas valve’s internal pressure regulator blocked open so
that the gas pressure must be regulated upstream of the dryer. The pressure measured at each
gas valve pressure tap must be a consistent 10.5 inches (26.1 mb) water column. There is no
regulator or regulation provided in an L.P. dryer. The water column pressure must be regulated at
the source (L.P. tank) or an external regulator must be added to each dryer.
7<3(ꢀ2)ꢀ*$6
/LTXLGꢀ3URSDQH
&RQYHUVLRQꢀ.LW
3DUWꢀ1XPEHU
1DWXUDO
/LTXLGꢀ3URSDQH
NFDOꢁKU
5DWLQJ
%WXꢀꢁKU
3DUW
1XPEHU
3DUW
4W\ꢂ 'ꢂ0ꢂ6ꢂꢃ
4W\ꢂ 'ꢂ0ꢂ6ꢂꢃ
1XPEHU
ꢄꢉꢈꢋꢈꢊ
ꢂꢂꢃꢄꢅꢅ
ꢄꢅꢆꢇꢈꢈꢈ
ꢉ
'ꢊꢈ
ꢄꢉꢈꢋꢄꢌ
ꢉ
'ꢉꢌ
ꢋꢋꢊꢊꢍꢌ
Shaded area is stated in metric equivalent
* Drill Measurement Size (D.M.S.) equivalents are as follows:
Natural Gas ................... #30 = 0.1285” (3.2639 mm).
L.P. Gas ........................ #49 = 0.0730” (1.8542 mm).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Piping Connections
ALL components/materials must conform to National Fuel Gas Code SpecificationsANSI Z223.1-LATEST
EDITION, or in Canada, CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid
Propane [L.P.] Gas) or LATESTEDITION (for General Installation and Gas Plumbing), as well as local
codes and ordinances and must be done by a qualified professional. It is important that gas pressure
regulators meet applicable pressure requirements, and that gas meters be rated for the total amount of
ALL the appliance Btus being supplied.
The dryer is provided with a 3/4” N.P.T. inlet pipe connection located at the right side of the base of the
dryer. The minimum pipe size (supply line) to the dryer is 3/4” diameter. For ease in servicing, the gas
supply line of each dryer must have its own shutoff valve.
The size of the main gas supply line (header) will vary depending on the distance this line travels from the
gas meter or, in the case of L.P. gas, the supply tank, other gas-operated appliances on the same line, etc.
Specific information regarding supply line size should be determined by the gas supplier.
NOTE: Undersized gas supply piping can create a low or inconsistent pressure, which will result in
erratic operation of the burner ignition system.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Consistent gas pressure is essential at ALL gas connections. It is recommended that a 3/4-inch (19.05
mm) pipe gas loop be installed in the supply line servicing a bank of dryers. An in-line pressure regulator
must be installed in the gas supply line (header) if the (natural) gas pressure exceeds 12.0 inches (29.9
mb) of water column (W.C.) pressure.
NOTE: A water column test pressure of 3.5 inches (8.7 mb) for natural gas and 10.5 inches (26.1 mb)
for liquid propane (L.P.) dryers is required at the gas valve pressure tap of each dryer for
proper and safe operation.
A 1/8” N.P.T. plugged tap, accessible for a test gauge connection, must be installed in the main gas supply
line immediately upstream of each dryer.
IMPORTANT: Pipe joint compounds that resist the action of natural gas and L.P. gas must be used.
IMPORTANT: Test ALL connections for leaks by brushing on a soapy water solution (liquid
detergent works well).
WARNING: NEVER TEST FOR LEAKS WITHA FLAME!!!
IMPORTANT: The dryer and its individual shutoff valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of
1/2 psig (3.5 kPa).
NOTE: The dryer must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure test of the gas supply system at test pressures equal to or
less than 1/2 psig (3.5 kPa).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
H. PREPARATION FOR OPERATION/START-UP
The following items should be checked before attempting to operate the dryer:
1. Read ALL “CAUTION,” “WARNING,” and “DIRECTION” labels attached to the dryer.
2. Check incoming supply voltage to be sure that it is the same as indicated on the dryer data label. In the case
of 208 VAC or 240 VAC, the supply voltage must match the electric service specifications of the data
exactly.
3. Check to ensure that the dryer is connected to the type of heat/gas indicated on the dryer data label.
4. The sail switch damper assembly was installed and adjusted at the factory prior to shipping. However,
each sail switch adjustment must be checked to ensure that this important safety control is functioning.
(Refer to sail switch adjustment on page 29.)
5. Check bolts, nuts, screws, terminals, and fittings for tightness and security.
6. Be sure that ALL gas shutoff valves are in the open position.
7. Check ALL back guard panels and service box covers have been replaced.
8. Check the lint drawer to ensure that it is closed and secured in place.
9. Rotate the basket (tumbler/drum) by hand to be sure it moves freely.
10. Check basket (tumbler) bearing setscrews to ensure that they are ALL tight.
11. Check vent is connected to the dryer and is exhausted to the outdoors.
12. There should be a source of fresh air entering the room. This source should not be near where the
dryers exhaust to the outside.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
I. PREOPERATIONAL TESTS
ALL dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational test
should be performed before the dryer is publicly used. It is possible that adjustments have changed in transit or
due to marginal location (installation) conditions.
1. Turn on electric power to the dryer.
2. Refer to the Operating Instructions for starting your particular model dryer.
a. When a gas dryer is first started (during initial start-up), it has a tendency not to ignite on the first ignition
attempt. This is because the gas supply piping is filled with air, so it may take a few minutes for the air
to be purged from the lines.
NOTE: During the purging period, check to be sure that ALL gas shutoff valves are open.
NOTE: Gas dryers are equipped with a Direct Spark Ignition (DSI) system, which has internal
diagnostics. If ignition is not established within three (3) times, the heat circuit in the DSI
module will “LOCK OUT” until it is manually reset. To reset the DSI system, open and close
the main door and restart the dryer.
b. A gas pressure test should be taken at the gas valve pressure tap of each dryer to ensure that the
water column (W.C.) pressure is correct and consistent.
NOTE: Water column pressure requirements (measured at the pressure tap of the gas valve body):
Natural Gas-------------------- 3.5 Inches (8.7 mb) Water Column.
Liquid Propane (L.P.) Gas --- 10.5 Inches (26.1 mb) Water Column.
IMPORTANT: There is no regulator provided in an L.P. dryer. The water column pressure must be
regulated at the source (L.P. tank), or an external regulator must be added to each
dryer.
4. Make a complete operational check of ALL safety related circuits:
a. Door Switch(es)
b. Hi-Limit Thermostats
c. Cycling Thermostat
d. Sail Switch
27
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: To check for proper sail switch operation, open the main door and while holding main door
switch plunger in, start dryer. Dryer should start but heat circuit should not be activated (on).
If the heat system is activated, the sail switch is improperly adjusted and must be adjusted by
bending the actuator arm of the sail switch toward the burner box. If the actuator arm is bent
too far toward the burner box of the dryer, the dryer may not have heat when needed. After
any adjustment to the sail switch, the above procedure must be repeated to verify proper
operation of the sail switch.
5. Make a complete operational check of ALL operating controls.
NOTE: If computer program changes are required, refer to the computer programming section of the
manual supplied with the dryer.
6. The dryer should be operated through one (1) complete cycle to ensure that no further adjustments are
necessary and that ALL components are functioning properly.
BASKET (TUMBLER) COATING
The basket (tumbler) is treated with a protective coating. We suggest dampening old garments or cloth material
with a solution of water and nonflammable mild detergent and tumbling them in the basket (tumbler) to remove
this coating.
7. Check the electric service phase sequence (3-phase [3ø] models only). While the dryer is operating, check
to see if the blower (impellor/fan) wheel is rotating in the proper direction. Looking from the front, the
blower (impellor/fan) wheel should spin in the clockwise (CW) direction. If it is, the phasing is correct. If
the phasing is incorrect, reverse two (2) of the three (3) leads at connections L1, L2, and L3 of the power
supply to the dryer.
IMPORTANT: If the blower (impellor/fan) wheel is rotating in the wrong direction it will drastically
reduce drying efficiency and it can also cause premature component failure.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
J. PREOPERATIONAL INSTRUCTIONS
1. To start the dryer:
Microprocessor Controller (Computer) Dryers
a. Light emitting diode (L.E.D.) display will read “READY” (meaning no cycle in progress).
b. Press the letter on the keyboard (touch pad) corresponding to the cycle desired (i.e., key “E”) and the
dryer will then start.
c. L.E.D. display will now show “Cycle In Progress” and “Cycle Status” meaning that the dryer is in the
drying cycle (dry mode for 30 minutes) and count downwards in minutes.
NOTE: Pressing keyboard (touch pad) key “A,” “B,” “C,” “D,” or “F” will also start the dryer. The
six (6) preprogrammed drying cycles “A” through “F” have been stored in the microprocessor
controller (computer) memory. Refer to the Programming Manual supplied with the dryer for
more specific operating instructions.
NOTE: The dryer can be stopped at any time by opening the main door or by pressing the “STOP”
red key. To restart the dryer, press the “START”
key (i.e., “E”).
green key or a preprogrammed cycle
NOTE: Selection (settings) changes can be made at any time during the drying cycle by pressing the
“STOP” red key twice. The L.E.D. display will return to “REAdY” at which time a
new cycle selection can be made.
DUAL TIMER DRYERS
1. Turn drying timer knob for a time of 20 minutes.
2. Select “High Temp.”
3. Push “Push to Start” switch.
4. To stop dryer, open the main door.
Spin and dwell (stop) times are adjustable at the reversing timer.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSING TIMER SPIN/DWELL ADJUSTMENTS
Timer models have an electronic reversing timer in the electrical service box, which is located in the upper left
rear area of the dryer.
Both the Dwell (stop) Time and the basket (tumbler) Spin Time are adjustable by mode selection switches
located on the electronic timer (as noted in the illustration below).
7,0,1*ꢀ/(*(1'
K. SHUTDOWN INSTRUCTIONS
If the dryer is to be shutdown (taken out of service) for a period of time, the following must be performed:
1. Discontinue power to the dryer either at the external disconnect switch or the circuit breaker.
2. Discontinue the gas supply and SHUT OFF external gas supply shutoff valve.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION IV
SERVICE/PARTS INFORMATION
A. SERVICE
Service must be performed by a qualified trained technician,service agency, or gas supplier. If service is
required, contact the Maytag dealer from whom the equipment was purchased. If the dealer cannot be
contacted or is unknown, contact the Maytag Co. for a dealer in your area.
NOTE: When contacting the Maytag Co., be sure to give them the correct model number and
serial number so that your inquiry is handled in an expeditious manner.
B. PARTS
Replacement parts should be purchased from the dealer from whom the Maytag equipment was purchased. If
the dealer cannot be contacted or is unknown, contact the Maytag Co. for a dealer in your area.
NOTE: When ordering replacement parts from the Maytag dealer or the Maytag Co. be sure to give
them the correct model number and serial number so that your parts order can be
processed in an expeditious manner.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION V
ROUTINE MAINTENANCE
A. CLEANING
A program and/or schedule should be established for periodic inspection, cleaning, and removal of lint from
various areas of the dryer, as well as throughout the ductwork system. The frequency of cleaning can best be
determined from experience at each location. Maximum operating efficiency is dependent upon proper air
circulation. The accumulation of lint can restrict this airflow. If the guidelines in this section are met, a Maytag
dryer will provide many years of efficient, trouble free, and most importantly safe operation.
WARNING: LINT FROM MOST FABRICS IS HIGHLYCOMBUSTIBLE. THE
ACCUMULATION OFLINT CAN CREATEAPOTENTIALFIRE HAZARD.
WARNING: KEEPDRYERAREACLEAR AND FREE FROM COMBUSTIBLE
MATERIALS, GASOLINE, AND OTHER FLAMMABLE VAPORS AND
LIQUIDS.
NOTE: Suggested time intervals shown are for average usage which is considered six (6) to eight (8)
operational (running) hours per day.
IMPORTANT: Dryer produces combustible lint and must be exhausted to the outdoors. Every 6
months, inspect the exhaust ducting and remove any lint buildup.
SUGGESTED CLEANING SCHEDULE
EVERY THIRD OR FOURTH LOAD
Clean the lint screen every third or fourth load. A clogged lint screen will cause poor dryer performance. The
lint screen is located in a drawer below the main door. Open the lint drawer, brush or vacuum the lint off the lint
screen, and remove the lint. Inspect lint screen and replace if torn.
NOTE: The frequency of cleaning the lint screen can best be determined from experience at each
location.
WEEKLY
Clean lint accumulation from lint chamber, thermostat, and microprocessor temperature sensor (sensor bracket)
area.
WARNING: TOAVOID THE HAZARD OFELECTRICALSHOCK, DISCONTINUE
ELECTRICALSUPPLYTOTHE DRYER.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
90 DAYS
Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryer’s internal
exhaust ducting.
WARNING: THEACCUMULATION OFLINT IN THE EXHAUST DUCTWORK CAN
CREATEAPOTENTIALFIRE HAZARD.
WARNING: DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION
AIR.
WARNING: INSPECT AND REMOVEANY LINTACCUMULATION, WHICH CAN CAUSE
THE BACK DRAFT DAMPER TO BIND OR STICK.
NOTE: A back draft damper that is sticking partially closed can result in slow drying and shutdown of
heat circuit safety switches or thermostats.
NOTE: When cleaning the dryer cabinet(s), avoid using harsh abrasives. Aproduct intended for the
cleaning of appliances is recommended.
B. ADJUSTMENTS
7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTER
Inspect bolts, nuts, screws, setscrews, grounding connections, and nonpermanent gas connections (unions, shutoff
valves, and orifices). Motor and drive belts should be examined. Cracked or seriously frayed belts should be
replaced. Tighten loose V-belts when necessary. Complete operational check of controls and valves. Complete
operational check of ALL safety devices (door switches, lint drawer switch, sail switch, burner, and hi-limit
thermostats).
C. LUBRICATION
The motor bearings, idler bearings, and under normal/most conditions, the basket (tumbler) bearings are permanently
lubricated. It is physically possible to relubricate the basket (tumbler) bearings if you choose to do so even
though this practice is not necessary. Use Shell Alvania #2 grease or its equivalent. The basket (tumbler)
bearings used in the dryer DO NOT have a grease fitting. Provisions are made in the bearing housing for the
addition of a grease fitting which can be obtained elsewhere, or from Maytag by ordering kit P/N 882159
(includes two [2] fittings).
33
Download from Www.Somanuals.com. All Manuals Search And Download.
D. LINT DRAWER REMOVAL
To remove the lint drawer from the dryer pull drawer out approximately halfway. Rotate/move lint drawer stop
hinge (refer to the illustration below) downward and pull drawer out.
IMPORTANT: After replacing the lint drawer back into the dryer, be sure to rotate/move hinge back
to the upward stop position.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTIONVI
DATALABELINFORMATION
When contacting the Maytag dealer, or the Maytag Co., certain information is required to ensure proper
service/parts information. This information is on the data label affixed to the upper left side panel area behind
the top control (access) door. When contacting Maytag Co., please have the model number and serial
number available.
1. MODEL NUMBER – Describes the size of the dryer and the type of heat (gas, electric, or steam).
2. SERIALNUMBER –Allows the manufacturer to gather information on your particular dryer.
3. MANUFACTURINGCODE NUMBER –The number issued by the manufacturer, which describes ALL possible options
on your particular model.
4. TYPE OFHEAT – This describes the type of heat for your particular dryer, gas (either natural gas or liquid propane [L.P.]
gas), electric, or steam.
5. HEAT INPUT (for GAS DRYERS) – This describes the heat input in British Thermal Units per Hour (Btu/hr).
6. ORIFICE SIZE (for GAS DRYERS) – Gives the number drill size used.
7. ELECTRIC SERVICE – This describes the electric service for your particular model.
8. GAS MANIFOLD PRESSURE (for GAS DRYERS) – This describes the manifold pressure taken at the gas valve tap.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTIONVII
PROCEDURE FOR FUNCTIONAL CHECK
OF REPLACEMENT COMPONENTS
1. Microprocessor Controller (Computer) Board
a. Upon completing installation of the replacement microprocessor controller (computer) board, reestablish
power to the dryer.
b. Start the drying cycle by pressing any of the preset cycles in letters A-F.
c. Verify that the applicable indicator lights on the back side of the microprocessor controller (computer)
board are lit. (Refer to the illustration below.)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
2. For Models with Johnson Direct Spark Ignition (DSI) Controller (G760)
Theory of Operation:
Start the drying cycle. When the gas burner ignites within the
chosen trial for ignition time (6-seconds), the flame sensor detects
gas burner flame and signals the DSI module to keep the gas
valve open as long as there is a call for heat. The DSI module
will “LOCK OUT” if the gas burner flame is not sensed at the
end of the trial for ignition period. The trial for ignition period will
be repeated for a total of three (3) retries/trials (the initial try and
two [2] more retries/trials). If the flame is not sensed at the end
of the third retry/trial (inter-purge period of 30-seconds) the DSI
module will “LOCK OUT” (light emitting diode [L.E.D.] diagnostic
indicator flashes).
A steady L.E.D. indicator indicates normal operation.
No L.E.D. indicator indicates a power or an internal failure has occurred.
3. For Models with Fenwal Controls DSI Module (128937)
Theory of Operation:
Start the drying cycle. When the gas burner ignites within the
chosen trial for ignition time (8-seconds), the flame sensor detects
gas burner flame and signals the DSI module to keep the gas
valve open as long as there is a call for heat. The DSI module
will “LOCK OUT” if the gas burner flame is not sensed at the
end of the trial for ignition period. The trial for ignition period will
be repeated for a total of three (3) retries/trials (the initial try and
two [2] more retries/trials). If the flame is not sensed at the end
of the third retry/trial (inter-purge period of 30-seconds), the DSI
module will “LOCK OUT” (a red L.E.D. diagnostic indicator will
flash).
An unlit red L.E.D. diagnostic indicator indicates normal operation.
AlitgreenL.E.D. diagnosticindicatorindicatesdryercontrolleriscallingforheatandthat ALL interlocks
have been satisfied.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTIONVIII
MANUAL RESET BURNER HI-LIMIT INSTRUCTIONS
A. PHASE 7
This dryer was manufactured with a manual reset burner hi-limit thermostat, which is monitored by the Phase 7
computer. If the burner hi-limit is open prior to the start of the drying cycle, the dryer will start momentarily and
then shut down, the Phase 7 computer will display “BURNER HIGH LIMIT FAULT” with an audio indication.
If the burner hi-limit opens during a drying cycle, the Phase 7 computer will also display the same error code
described above, along with an audio indication. If the drum temperature is above 100° F (38° C), the dryer will
continue to run with no heat for 3 minutes or until the drum temperature has dropped below 100° F (38° C). The
clear/stop button on the Phase 7 keyboard (touch pad) must be pressed to clear the error condition. The open
burner hi-limit must be reset “manually” prior to the start of the next cycle.
B. DUAL TIMER
This dryer was manufactured with a manual reset burner hi-limit thermostat. If the burner hi-limit is open prior
to the start of the drying cycle, or during the cycle, the dryer will not recognize the open state of the burner
hi-limit and will start or continue through the drying cycle with no heat. Manual reset hi-limit must be reset
manually.
This hi-temperature condition may be caused due to a restricted exhaust, poor airflow, or improper burner
operation.
The location of the burner hi-limit is on the right side of the burner box, looking at the burner from the back of the
dryer.
WARNING: Discontinue power to dryer before attempting to reset hi-limit.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION IX
SENSORACTIVATED FIRE EXTINGUISHING (S.A.F.E.)
SYSTEM
S.A.F.E. System In Action
The exclusive Sensor Activated Fire Extinguishing (S.A.F.E.) System will extinguish fires that may start in the
drying basket (tumbler). A series of sensors positioned throughout the basket (tumbler) and interfaced with the
microprocessor controller (computer) will trigger the S.A.F.E. system water jet(s) to extinguish the flames
quickly. The water jet(s) remain on for 2 minutes and will automatically activate again if a fire condition remains
or reignites. While the water jet(s) are activated, the basket (tumbler) will jog to move the water throughout the
load. The microprocessor controller (computer) will display until the dryer is attended to, that the system was
activated.
BEFORE YOU START!
CHECK LOCAL CODES AND PERMITS
Call your local water company or the proper municipal authority for information regarding local codes.
IMPORTANT: It is your responsibility to have ALL plumbing connections made by a qualified
professional to assure that the plumbing installation is adequate and conforms to local,
state, and federal regulations or codes.
IMPORTANT: It is the installation or owners responsibility to see that the necessary or required
water, water pressure, pipe size, or connections are provided. The manufacturer
assumes no responsibility if the S.A.F.E. system is not connected, installed, or
maintained properly.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
1. Requirements
The S.A.F.E. system must be supplied with a minimum water pipe size of 1/2” and be provided with 40 psi
+/- 20 psi (2.75 bar +/- 1.37 bar) of pressure. For use of optional manual bypass, a second source with the
same piping and pressure requirements is required.
Flexible 1/2 feeds must be provided to avoid damage to electric water solenoid valve by vibration.
IMPORTANT: Flexible supply line/coupling must be used. Solenoid valve failure due to hard
plumbing connectionsWILLVOIDWARRANTY.
If the rear area of the dryer, or the water supply is located in an area where it will be exposed to cold/
freezing temperatures, provisions must be made to protect these water lines from freezing.
WARNING: If the water in the supply line or water solenoid valve freezes, the S.A.F.E. system will
be INOPERATIVE!!
IMPORTANT: Appliance is to be connected to the water mains using a new hose-set and the old
hose-sets should not be reused.
2. Water Connections:
The water connection is made to the 3/4”-11.5
NH hose adapter of the electric water solenoid
valve, located at the rear upper midsection of the
dryer (refer to the photograph).
The water solenoid valve has a 3/8” M.P.T.
connection supplied with a 3/4”-11.5 NH hose
adapter to provide the minimum 1/2-inch supply
(feed) line. Flexible supply line/coupling must
be used in an effort to avoid damaging the electric
water solenoid valve.
NOTE: The 3/4”-11.5 NH is a standard hose coupling screw thread. It is not to be confused with
3/4” N.P.T. The sealing of an NH connection is made with a washer opposed to the mating
threads of an N.P.T. assembly. The two (2) thread designs are not compatible.
IMPORTANT: Flexible supply line/coupling must be used. Solenoid valve failure due to hard
plumbing connections WILLVOID WARRANTY. It is recommended that a filter
or strainer be installed in the water supply line.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Water Supply
OPTIONAL MANUAL BYPASS
Provisions are made in the dryer S.A.F.E. system for the installation of an optional manual bypass. Depending
on the model dryer, the connections for the manual bypass are made at the “T” or “four way” fitting located in
the outlet supply side of the water solenoid valve. The use and connections of this manual bypass are at the
option or discretion of the owner.
The water connection for the manual bypass is made to the “T” or “four way” fitting which has a 3/8” F.P.T. and
a coupling must be used to provide the minimum 1/2” supply (feed) line.
If the rear area of the dryer, or the water supply is located in an area where it will be exposed to cold/freezing
temperatures, provisions must be made to protect these water lines from freezing.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: If the water in the supply line or water solenoid valve freezes, the S.A.F.E. system will
be INOPERATIVE!!
The manual ball cock shutoff valve must be located outside of the dryer at a distance from the dryer where it
is easily accessible.
3. Electrical Requirements
No independent external power source or supply connection is necessary. The 24 volt power to operate the
S.A.F.E. system is accomplished internally in the dryer (from the dryer controls).
WARNING: Electrical power must be provided to the dryer at ALL times. If the main electrical
power supply to the dryer is disconnected, the S.A.F.E. system is INOPERATIVE!!
S.A.F.E. System Theory of Operation
While the dryer is in an idle state, or 20-seconds after the heat turns off, the Phase 7 control monitors the
thermistor probe, located in the top of the basket (tumbler) chamber, and records the minimum temperature. If
the minimum recorded thermistor probe temperature is greater than 120° F (48° C) and the control detects a 50°
rise in temperature, this will be the trip point and the S.A.F.E. system routine will activate.
While a drying cycle is in process and the heat has turned on at least once, the Phase 7 control monitors the
exhaust temperature transducer. If the drying cycle temperature set point is set greater than 160° F (71° C) and
the control detects an exhaust temperature rise 25° F greater than set point, this will be the trip point and the
S.A.F.E. system routine will activate. If set point is below 160° F (71° C), the trip point will be 185° F (85° C).
Once the S.A.F.E. system routine is activated, the control will display “S.A.F.E. SYSTEM ACTIVATED” and
water will be injected into the basket (tumbler) chamber. Any time water is being injected into the basket
(tumbler), the basket (tumbler) drive will turn the load for 1-second every 15-seconds. This process will continue
for a minimum of 2 minutes. After the 2 minutes have elapsed, the control will check if the temperature
remained above trip point; if so, the water will remain on. The control will continue to check if the temperature
is above trip point every 30-seconds. If the water has been on for a constant 10 minutes, the water will be turned
off, regardless of the temperature, and the control will display “S.A.F.E. SYSTEM WAS ACTIVATED.” If the
temperature has dropped below trip point, the control will turn off the water prior to 10 minutes.
System Reset
After the microprocessor controller (computer) determines that the situation is under control and shuts the water
being injected into the basket (tumbler) off, the microprocessor controller (computer) display will read “S.A.F.E.
SYSTEM WAS ACTIVATED,” and the horn/tone will sound until reset manually.
To reset the microprocessor controller (computer) once the control displays “S.A.F.E. SYSTEM WAS
ACTIVATED,” press the red “STOP/CLEAR” key on the keyboard (touch pad).
42
Download from Www.Somanuals.com. All Manuals Search And Download.
S.A.F.E. System Water Valve Check
The operation of the water solenoid valve can be tested to ensure that the water supply system and valve are
functional. Before attempting a system check, be sure that ALL water supply shutoff valves to the dryer are in
the OPEN position; the dryer must be in the “READY” mode with no cycle loaded or in progress.
1. Press and hold the red “STOP/CLEAR” key (while in “READY” mode and no cycle is in progress).
2. Press and hold the “A” key.
3. Water valve will open and water will be dispensed into basket (tumbler) area as long as both keys are held.
The Phase 7 non-coin microprocessor controller (computer) will prompt the user to perform a S.A.F.E. system
valve check at every 4000 hours to ensure proper functionality. At the 4000 hour mark, the control will wait for
end of the cycle and then will prompt the user to “PLEASE EMPTY TUMBLER, THEN PRESS THE
‘STOP/CLEAR’AND ‘A’ KEYS TO TESTTHEWATERVALVE.” When the ‘STOP/CLEAR’and ‘A’ keys
are pressed, the control will activate the S.A.F.E. system water valve for 2-seconds, at which point the control
will prompt the user with the following message: “IFWATER DID NOTTURN ON, CALLFOR SERVICE.
THANK YOU.”
NOTE: The control will not let the user continue until the valve test has been completed.
S.A.F.E. System Diagnostics
In the event that the Phase 7 non-coin microprocessor controller (computer) detects a fault in the S.A.F.E.
system, the microprocessor controller (computer) will display the message “S.A.F.E. SYSTEM
DISABLEDꢀREADY.” To find out why the S.A.F.E. system is disabling, press and hold the red “STOP/
CLEAR” and green “START” keys. This will cause the microprocessor controller (computer) to display a
diagnostic message, as detailed in the “S.A.F.E. SYSTEM Diagnostics Messages” section.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
S.A.F.E. System Diagnostics Messages
OPEN THERMISTOR PROBE – This message indicates that the S.A.F.E. system thermistor probe either is
not connected or is damaged. If this condition is detected, the Phase 7 non-coin control will immediately enter
S.A.F.E. SYSTEM DISABLED mode.
SHORTED THERMISTOR PROBE – This message indicates that the S.A.F.E. system thermistor probe is
damaged or the wiring is shorted. If this condition is detected, the Phase 7 non-coin control will immediately
enter S.A.F.E. SYSTEM DISABLED mode.
DISCONNECTED WATER VALVE – This message indicates that the water valve is open or that it is not
connected to the control. If this condition is detected, the Phase 7 non-coin control will continue to monitor the
condition for a period of 5 minutes before entering S.A.F.E. SYSTEM DISABLED mode. Once the condition
is corrected, the control will continue to monitor the condition for 1 minute before exiting S.A.F.E. SYSTEM
DISABLED mode.
SHORTED WATER VALVE – This message indicates that the water valve is shorted or that the wiring to the
valve is shorted. If this condition is detected, the Phase 7 non-coin control will continue to monitor the condition
for a period of 5 minutes before entering S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected,
the control will continue to monitor the condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED
mode.
WATER NOT CONNECTED – This indicates that there is no water pressure at the water valve. This will
occur if water is not connected to the dryer, or if there is low water pressure in the water line coming to the
dryer. This could also signify a defective pressure switch or defective wiring to the pressure switch. If this
condition is detected, the Phase 7 non-coin control will continue to monitor the condition for a period of 5 minutes
before entering S.A.F.E. SYSTEM DISABLED mode. Once the condition is corrected, the control will continue
to monitor the condition for 1 minute before exiting S.A.F.E. SYSTEM DISABLED mode.
STARTING A CYCLE
WHEN COMPUTER IS IN “S.A.F.E. SYSTEM IS DISABLED” MODE
When the S.A.F.E. system is disabled, the user can still start a cycle. However, when a cycle is started, the
microprocessor controller (computer) will display the following message: “S.A.F.E. SYSTEM IS DISABLED.
PRESS ‘START’ TO CONTINUE.” This message will be displayed every time a cycle is started, until the
disabling condition has been corrected.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
113394
4 - 02/18/04 - 150
Download from Www.Somanuals.com. All Manuals Search And Download.
|