G5 CABLE MOTION
™
GYM SYSTEM
ASSEMBLY INSTRUCTIONS
G5-001 / CLASS H / 09/30/08 / 8289201 REV. B
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION
1. DO NOT use or permit use of any equipment that is damaged and or has worn or broken parts. For all
LIFE FITNESS equipment use only replacement parts supplied by LIFE FITNESS.
2. Cables and Belts pose an extreme liability if used when frayed. Always replace any cable at first sign of
wear (consult LIFE FITNESS if uncertain).
3. Routinely inspect all accessory clips that join attachments to the cables and replace at the first sign of
wear.
4. MAINTAIN LABELS AND NAMEPLATES - Do not remove labels for any reason. They contain important
information. If unreadable or missing, contact LIFE FITNESS for a replacement.
5. EQUIPMENT MAINTENANCE - Preventative maintenance is the key to smooth operating equipment as
well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.
6. Ensure that any person(s) making adjustments or performing maintenance or repair of any kind is quali-
fied to do so. LIFE FITNESS will provide service and maintenance training at our corporate facility upon
request or in the field if proper arrangements are made.
7. Before any use, examine all accessories approved for use with the LIFE FITNESS equipment for
damage or wear.
8. DO NOT ATTEMPT TO USE OR REPAIR ANY ACCESSORY APPROVED FOR USE WITH THE LIFE
FITNESS EQUIPMENT WHICH APPEARS TO BE DAMAGED OR WORN.
OPERATING WARNINGS
1. It is the purchaser's sole responsibility to properly instruct its end users and supervising personnel as to
the proper operating procedures of all LIFE FITNESS equipment.
2. Keep children away from strength equipment. Parent or others supervising children must provide close
supervision of children if the equipment is used in the presence of children.
3. Do not allow users to wear loose fitting clothing or jewelry while using equipment. It is also recommend-
ed to have user's secure long hair back and up to avoid contact with moving parts.
4. All bystanders must stay clear of all users, moving parts and attached accessories and components
while machine is in operation.
SELECTORIZED WEIGHT STACK SYSTEMS
1. Use only weight selector pins supplied by LIFE FITNESS on weight stacks. Substitutes are forbidden.
2. Fully insert weight selector pins. Partial insertion can cause weights to fall unexpectedly.
3. Never pin the weight stack in an elevated position.
4. Never remove selector pin if any weights are suspended.
5. Never attempt to release jammed weights or parts.
6. Never use dumbbells or other means to incrementally increase the weight resistance. Use only those
means provided by LIFE FITNESS.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
G5 WARNING LABELS
NOTE: Lock the weight stack when not using the gym. Make sure all the weight plates are rest-
ing on the plate below with no gap in between. Insert the weight selector pin in the tab under-
neath the weight stack. The weight selector pin should be inserted until the knob touches the
metal tab. Once the pin goes through the weight stack system, the weight stack becomes immo-
bile. Verify that the pin has gone through the weight stack stem.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GYM DIMENSIONS
Resistance Ratio: 1:2
Machine Weight:
Weight Stack:
500 pounds
160 pounds
5
Download from Www.Somanuals.com. All Manuals Search And Download.
G5 LIVE AREA
12”
12”
11’-3”
13’-4”
NOTE: The live area shows the extent of the G5 gym. It does not include the user.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS LIST
NOTE: This component list is for ASSEMBLY ONLY. For ordering serviceable parts, please go to:
ITEM NO.
QTY.
DESCRIPTION
1
1
FRONT UPRIGHT
2
1
1
1
1
1
1
2
15
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
2
2
6
1
1
1
2
2
1
UPPER SWIVEL PULLEYS
LEFT UPRIGHT
3
4
RIGHT UPRIGHT
LEFT BASE
5
6
RIGHT BASE
7
FOOT PLATE
8
GUIDE ROD
9
WEIGHT PLATE
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
HEAD PLATE PULLEY
SELECTOR PIN
TOP PLATE
WEIGHT STACK CUSHION
FLOATING PULLEYS
FRONT SHROUD
RIGHT BOTTOM PLATE
LEFT BOTTOM PLATE
BACK THIGH HOLD CLAMP
THIGH HOLD DOWN
TOP BACK COVER
TOP FRONT COVER
MOUNTING SHEET
TOP COVER
TOP RIGHT COVER
TOP LEFT COVER
SHORT HANDLE
MEDIUM HANDLE
ADJUSTABLE HANDLE
UPPER (LONG) CABLE
LOWER (SHORT) CABLE
GUIDE CABLE
QUICK CONNECT
FOOT STRAP
THIGH STRAP
ADAPTER BAR
SNAP LINKS
UNIVERSAL RINGS
EXERCISE BALL
7
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENTS LIST
HARDWARE
ITEM NO.
QTY.
DESCRIPTION
39
14
3/8” WASHER
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
4
8
4
8
4
2
2
4
2
2
4
2
2
4
8
2
M10 X 30MM SCREW
M10 X 70MM SCREW
M12 X 80MM SCREW
1/2” WASHER
M12 HEX NYLOCK NUT
M10 X 50 HEX TENSION SCREW
GUIDE ROD RETAINER
M4 X 0.7MM ZINC PHILLIPS PAN HEAD SCREW
M10 X 20MM SCREW
RETAINING RING
#10-32 X 3/4” PHILLIPS PAN HEAD SCREW
M6 X 60MM SCREW
1/4” WASHER
M10 HEX NYLOCK NUT
M4 ZINC PHILLIPS PAN HEAD SCREW
#6 X 3/8” BLACK PHILLIPS PAN HEAD SCREW
REQUIRED TOOLS
ADJUSTABLE WRENCH
EXTERNAL SNAP RING PLIERS
PHILLIPS SCREW DRIVER
ALLEN WRENCHES (4mm, 7mm, 8mm)
WRENCHES (13mm, 17mm, 19mm)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE:
M10 X 30MM SCREW (#40)
3/8” WASHER (#39)
1/2” WASHER (#43)
M10 X 70MM SCREW (#41)
M12 HEX NYLOCK NUT (#44)
M10 X 20MM SCREW (#48)
M12 X 80MM SCREW (#42)
M4 X 0.7mm ZINC
PHILLIPS PAN HEAD
SCREW (#47)
M10 X 50MM HEX TENSION SCREW (#45)
RETAINING RING (#49)
#10-32 X 3/4”
PHILLIPS PAN HEAD
SCREW (#50)
M6 X 60MM SCREW (#51)
1/4” WASHER (#52)
M4 ZINC
PHILLIPS PAN HEAD
SCREW (#54)
#6 X 3/8” BLACK
PHILLIPS PAN HEAD
SCREW (#55)
M10 HEX
NYLOCK NUT (#53)
Centimeters
9
Download from Www.Somanuals.com. All Manuals Search And Download.
40
2
39
4
3
1
A
44 43
43 42
6
STEP 1:
‰ Slide the RIGHT BASE (6) over the MOUNTING TUBE (A) of the RIGHT UPRIGHT (4). Loosely secure the RIGHT
BASE (6) and RIGHT UPRIGHT (4) to the FRONT UPRIGHT (1) using two M12 x 80mm SCREWS (42), four 1/2”
WASHERS (43), and two M12 HEX NYLOCK NUTS (44) as shown.
‰ With the UPPER SWIVEL PULLEYS (2) oriented as shown, insert the UPPER SWIVEL PULLEYS (2) into the top of
the RIGHT UPRIGHT (4) and secure together the RIGHT UPRIGHT (4), FRONT UPRIGHT (1), and UPPER SWIV-
EL PULLEYS (2) using two M10 x 30mm SCREWS (40) and two FLAT 3/8” WASHERS (39).
‰ Repeat the above steps to assemble the LEFT UPRIGHT (3) and LEFT BASE (5) to the FRONT UPRIGHT (1).
NOTE: THE UPPER SWIVEL PULLEYS (2) ATTACH TO THE INSIDE OF THE UPRIGHT SIDES AND THE ORIENTA-
TION SHOULD BE AS SHOWN.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
41
39
5
41
39
6
7
STEP 2:
‰ LOOSELY attach the FOOTPLATE (7) to the RIGHT BASE (6) and LEFT BASE (5) using four M10 x 70mm
SCREWS (41) and four FLAT 3/8” WASHERS (39).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
46
49
10
11
45
46
8
1”
45
12
9
8
1
13
B
STEP 3:
‰ Position two WEIGHT STACK CUSHIONS (13) and GUIDE RODS (8) at the GUIDE ROD BRACKET (B) on the bot-
tom of the FRONT UPRIGHT (1).
NOTE: MAKE SURE THAT THE PLUGGED ENDS OF THE GUIDE RODS (8) ARE FACING UP.
‰ CAREFULLY slide one of the WEIGHT PLATES (9) over the top of the GUIDE RODS (8) and slowly lower the
WEIGHT PLATE (9) on to the WEIGHT STACK CUSHIONS (13).
‰ Continue stacking a total of 15 WEIGHT PLATES (9).
‰ Slide the TOP PLATE (12) over the GUIDE RODS (8) and slowly lower it onto the WEIGHT PLATES (9).
‰ Slide the SELECTOR PIN (11) over the stem of the TOP PLATE (12).
‰ Thread the HEAD PLATE PULLEY (10) into the TOP PLATE (12).
‰ Slide one RETAINING RING (49) over the top of each of the GUIDE RODS (8).
‰ Thread one M10 x 50mm HEX TENSION SCREW (45) into each of the two GUIDE ROD RETAINERS (46). Do not
fully thread the M10 x 50mm HEX TENSION SCREWS (45) into the GUIDE ROD RETAINERS (46).
‰ CAREFULLY slide the GUIDE ROD RETAINERS (46) into the hole under the top of the FRONT UPRIGHT (1). Make
sure the M10 x 50mm HEX TENSION SCREWS (45) in the GUIDE ROD RETAINERS (46) are facing up.
‰ Push the GUIDE ROD RETAINERS (46) up high enough so that the GUIDE RODS (8) can be placed under them.
‰ Lower the GUIDE ROD RETAINERS (46) over the GUIDE RODS (22).
‰ Slide the RETAINING RINGS (49) up. Use External Snap Ring Pliers to secure the RETAINING RINGS (49) into the
groove on the GUIDE ROD RETAINERS (46).
‰ Tighten all frame bolts securely.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
C
2
14
2
10
29
STEP 4:
‰ Remove one QUICK CONNECT from the end of one UPPER (LONG) CABLE (29).
‰ Insert the end (where the QUICK CONNECT was removed) of the UPPER (LONG) CABLE (29) through the
UPPER SWIVEL PULLEYS (2) and follow routing illustration to the FLOATING PULLEYS (14) through to the
HEAD PLATE PULLEY (10). Continue to the other side, ending at the other UPPER SWIVEL PULLEYS (2).
Reattach the previously removed QUICK CONNECT to the end of the UPPER (LONG) CABLE (29).
NOTE: THE CABLE MUST BE INSERTED BETWEEN THE PULLEY AND THE CABLE RETAINING CLIPS (C) AND
MOVE FREELY.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
32
D
QTY.
DESCRIPTION
6
1
1
1
1
2
QUICK CONNECT ASSEMBLY
QUICK CONNECT COUPLER
QUICK CONNECT HOUSING
QUICK CONNECT SLEEVE
COMPRESSION SPRING
M5 HEX SCREWS
E
F
G
D
H
F
G
E
H
Cable
Slide Mechanism to insert
or Exchange Handles
F
STEP 5:
‰ Dissemble the QUICK CONNECT (32) by removing the two M5 HEX SCREWS (H) from the QUICK CONNECT
COUPLER (D). Carefully remove the COMPRESSION SPRING (G), the QUICK CONNECT SLEEVE (F) and the
QUICK CONNECT HOUSING (E).
‰ Slide the QUICK CONNECT HOUSING (E), COMPRESSION SPRING (G), and QUICK CONNECT SLEEVE (F) onto
the cable as shown. Insert the cable end into the QUICK CONNECT COUPLER (D).
‰ Slide the entire assembly over the QUICK CONNECT COUPLER (D). Attach the QUICK CONNECT COUPLER (D)
and QUICK CONNECT HOUSING (E) together. Use the two M5 HEX SCREWS (H) to tighten.
NOTE: IF NECESSARY, ENSURE THE CABLES ARE THE PROPER LENGTH AND MAKE NECESSARY ADJUST-
MENTS TO THE WEIGHT STACK PULLEY (TIGHTEN OR LOOSEN).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
1
I
50
16
55
50
15
16
17
STEP 6:
‰ Mount the RIGHT BOTTOM PLATE (16) and the LEFT BOTTOM PLATE (17) to the FRONT UPRIGHT (1) using two
10-32 x 3/4” PHILLIPS PAN HEAD SCREWS (50) for each plate.
‰ Place the FRONT SHROUD (15) around the FRONT UPRIGHT (1).
‰ Align the bottom mounting holes of the FRONT SHROUD (15) with the remaining mounting holes on the RIGHT
BOTTOM PLATE (16) and the LEFT BOTTOM PLATE (17). Secure with one 10-32 x 3/4” PHILLIPS PAN HEAD
SCREW (50) on each plate.
‰ Attach the bottom corners of the MID BACK COVER (I) to the back of the FRONT SHROUD (15) using two #6 x 3/8”
(9.5mm) BLACK PHILLIPS PAN HEAD SCREWS (55). DO NOT OVERTIGHTEN SCREWS INTO PLASTIC PARTS.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
30
K
7
30
J
L
STEP 7:
‰ Remove one QUICK CONNECT from the end of one LOWER (SHORT) CABLE (30).
‰ Insert the end (where the QUICK CONNECT was removed) of the the LOWER (SHORT) CABLE (30) through the
LOWER RIGHT PULLEY (J) and through the access hole in the FOOTPLATE (7). Continue routing the cable as
shown ending at the RIGHT MID PULLEY ASSEMBLY (K). Reattach the previously removed QUICK CONNECT to
the end of the LOWER (SHORT) CABLE (30).
NOTE: THE CABLE MUST BE INSERTED BETWEEN THE PULLEY AND THE PULLEY GUIDE (L) AND MOVE
FREELY.
‰ Repeat the routing on the left side of the unit using the remaining LOWER (SHORT) CABLE (30).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
1
15
18
19
1
41
15
51
18
52
39
53
STEP 8:
‰ Attach the BACK THIGH HOLD CLAMP (18) to the the FRONT UPRIGHT (1) by using two M6 x 60mm SCREWS
(51) and two 1/4” WASHERS (52) from the back of the FRONT UPRIGHT (1).
‰ Attach the THIGH HOLD DOWN (19) to the FRONT UPRIGHT (1) by using four M10 x 70mm SCREWS (41), eight
3/8” WASHERS (39), and four M10 HEX NYLOCK NUTS (53) through the FRONT SHROUD (15) and through the
FRONT UPRIGHT (1). Tighten SECURELY.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
20
54
54
21
STEP 9:
‰ Attach the TOP FRONT COVER (21) to the TOP BACK COVER (20) using eight M4 ZINC PHILLIPS PAN HEAD
SCREWS (54). DO NOT OVERTIGHTEN SCREWS INTO PLASTIC PARTS.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
14
1
M
14
N
31
STEP 10:
‰ Insert the ball end of one GUIDE CABLE (31) through the eye hook on one FLOATING PULLEYS (14). Insert and
hook the ball end of the cable into the SLOTTED BUSHING (N) located at the bottom of the frame located directly
below the FLOATING PULLEYS (14).
‰ Screw the threaded end of the cable into the FRONT UPRIGHT (1) and loosely tighten the cable by screwing the
JAM NUT (M) to the top of the frame.
‰ REPEAT THE ABOVE PROCESS FOR THE REMAINING GUIDE CABLE (31).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
23
24
22
25
47
1
39
48
STEP 11:
‰ Assemble the MOUNTING SHEET (22) to the top of the FRONT UPRIGHT (1) using two M10 x 20mm SCREWS
(48) and two 3/8” WASHERS (39). Tighten screws SECURELY.
‰ Attach the TOP LEFT COVER (25), the TOP RIGHT COVER (24) and the TOP COVER (23) to the MOUNTING
SHEET (22) using four M4 x 0.7 ZINC PHILLIPS PAN HEAD SCREWS (47). DO NOT OVERTIGHTEN SCREWS
INTO PLASTIC PARTS.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2
F
26
F
27
34
33
28
37
35
36
STEP 12:
‰ Referencing step 5, at the UPPER SWIVEL PULLEYS (2) push back on the QUICK CONNECT SLEEVE (F) at the
end of each cable and attach the SHORT HANDLES (26).
‰ Repeat the process for attaching the ADJUSTABLE HANDLES (28) to the lower cable ends and the MEDIUM HAN-
DLES (27) to the middle cable ends.
NOTE: THE HANDLE CONFIGURATION DEFINED WILL ACCOMMODATE MOST EXERCISES.
NOTE: THE FOOT STRAP (33) IS TO BE ATTACHED TO ONE OF THE MID SECTION PULLEY CABLE ENDS FOR
LEG EXTENSIONS AND TO ONE OF THE LOWER PULLEY CABLE ENDS FOR LEG CURL EXERCISES.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using
warm soapy water. Touch-up paint can be purchased from your Life Fitness cus-
tomer service representative at (800) 351-3737.
* Inspect equipment before each use. Tighten all loose connections and replace worn
parts immediately. Failure to do so may result in serious injury.
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD ON-LINE
AT WWW.LIFEFITNESS.COM.
Model #:
_____________________________________
_____________________________________
Serial #'s:
Note: The Model/Serial Number label is located towards the bottom of the RIGHT UPRIGHT.
Date of Purchase: _____________________________________
Dealer’s Name
_____________________________________
Dealer’s Phone# _____________________________________
Thank you for purchasing the Life Fitness
G5 CABLE MOTION GYM SYSTEM
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Life Fitness® G5 Cable Motion™ Gym System
Life Fitness extends the following LIMITED WARRANTY to the original owner (proof of purchase required, keep your
receipt with this manual) of the Life Fitness product. The Warranty terms apply to IN HOME and LIGHT INSTITUTIONAL
USE ONLY.
1.
LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the Life Fitness product or a weld should crack
or break, it will be repaired or replaced by Life Fitness. Terms: IN HOME USE ONLY: Lifetime – for so long as the
Customer owns the Life Fitness product; LIGHT INSTITUTIONAL USE: Ten (10) years.
2.
LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, Life Fitness will
supply replacement parts: all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retain-
ing clips, adjustable pre-stretch slides, roller pad shafts, allen head bolts, weight selector pin, weight stack shaft,
set screws, protector caps, adjustment chain, cotter pin, plunger, spring and knob. Terms: IN HOME USE ONLY:
Lifetime – for so long as the Customer owns the Life Fitness product; LIGHT INSTITUTIONAL USE: One (1) year.
3.
4.
5.
LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in mate-
rial or workmanship, Life Fitness will repair or replace them, at its option. Terms: IN HOME USE ONLY: Three (3)
years; LIGHT INSTITUTIONAL USE: Ninety (90) days.
CONDITIONS AND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person
other than an authorized Life Fitness Service Center, any improper assembly, accident, or any other condition
resulting from occurrences beyond the control of Life Fitness will void this Limited Warranty.
REPLACEMENT AND REPAIR EXPENSES. Life Fitness will provide only replacement parts or repair under this
warranty. The Owner is responsible for all other costs. Such costs may include, but are not limited to: a. labor
charges for service, removal, repair or reinstallation of the Life Fitness product or any component part; b. shipping,
delivery, handling and administrative charges for returning parts to Life Fitness; and c. all necessary or incidental
costs related to installation of the replacement parts.
6.
7.
SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of Life Fitness), parts should be
shipped in their original carton or equivalent packaging, fully insured with shipping charges prepaid. Life Fitness
will not assume any responsibility for any loss or damage incurred in shipping.
CLAIM PROCEDURES. If service on your Life Fitness product is required during the warranty period, please con-
tact our Customer Service Department at 1-800-351-3737 (U.S. and Canada) or +1-847-288-3300 (outside of U.S.
and Canada) for instructions regarding returning or replacing parts. Please have available the following informa-
tion: (i) the dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product(s) (the serial number loca-
tion is called out on the final assembly drawing included with your assembly instruction); (iv) a description of the
nature of the problem.
8.
9.
OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which
vary depending on local law.
LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law,
shall have no greater duration than the warranty period set forth above. There are no warranties which extend
beyond the description in this Limited Warranty. Because local laws do not allow limitations on how long an implied
warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of Life Fitness with respect to
any Life Fitness product or the operation, repair or replacement of any Life Fitness product. Life Fitness shall not
be responsible for injury, loss of use of the Life Fitness product, inconvenience, loss or damage to personal prop-
erty, whether direct or indirect, and incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
Notes:
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CORPORATE HEADQUARTERS
5100 North River Road
Schiller Park, Illinois 60176 • U.S.A.
847.288.3300 • FAX: 847.288.3703
800.735.3867 (Toll-free within U.S.A., Canada)
INTERNATIONAL OFFICES
Austria
Life Fitness Austria
AMERICA’S
ASIA PACIFIC (AP)
Japan
North America
Vertriebs G.m.b.H.
Life Fitness Japan
Life Fitness Inc.
Dückegasse 7-9/3/36
1220 Vienna
AUSTRIA
Telephone: (+43) 1.61.57.198
Fax: (+43) 1.61.57.198.20
Nippon Brunswick Bldg., #8F
5-27-7 Sendagaya
Shibuya-Ku, Tokyo
Japan 151-0051
Telephone: (+81) 3.3359.4309
Fax: (+81) 3.3359.4307
5100 N River Road
Schiller Park, IL 60176 U.S.A
Telephone: (847) 288 3300
Fax: (847) 288 3703
Spain
Life Fitness IBERIA
Brazil
Life Fitness Do Brazil
China and Hong Kong
Life Fitness Asia Pacific LTD
C/Frederic Mompou 5,1º1ª
08960 Sant Just Desvern Barcelona
SPAIN
Telephone: (+34) 936 724 660
Fax: (+34) 936 724 670
Av. Dr. Dib Sauaia Neto 1478
Alphaville, Barueri, SP
06465-140
BRAZIL
Telephone: (800) 773 8282
Fax: (+55) 11.4133.2893
Room 2610, Miramar Tower
132 Nathan Road
Tsimshatsui, Kowloon
HONG KONG
Telephone: (+852) 2891.6677
Fax: (+852) 2575.6001
Italy
Life Fitness ITALIA S.R.L.
Latin America & Caribbean*
Life Fitness Inc.
Via Crivellin 7/N
37010 Affi Verona
ITALY
All Other Asia Pacific countries &
distributor business Asia Pacific*
5100 N River Road
Schiller Park, IL 60176 U.S.A
Telephone: (847) 288 3300
Fax: (847) 288 3703
Telephone: (+39) 045.7237811
Fax: (+39) 045.7238197
Room 2610, Miramar Tower
132 Nathan Road
Tsimshatsui, Kowloon
HONG KONG
Telephone: (+852) 2891.6677
Fax: (+852) 2575.6001
Belgium
Life Fitness Benelux NV
EUROPE, MIDDLE EAST, & AFRICA
(EMEA)
Parc Industrial de Petit-Rechain
4800 Verviers
BELGIUM
Telephone: (+32) 87 300 942
Fax: (+32) 87 300 943
Netherlands & Luxemburg
Life Fitness Atlantic BV
Bijdorpplein 25-31
2992 LB Barendrecht
THE NETHERLANDS
Telephone: (+31) 180 646 666
Fax: (+31) 180 646 699
All Other EMEA countries &
distributor business C-EMEA*
Bijdorpplein 25-31
2992 LB Barendrecht
THE NETHERLANDS
Telephone: (+31) 180 646 666
Fax: (+31) 180 646 699
United Kingdom & Ireland
Life Fitness UK LTD
Queen Adelaide
Ely, Cambs, CB7 4UB
Telephone: General Office (+44) 1353.666017 Customer
Support (+44) 1353.665507
Fax: (+44) 1353.666018
Germany & Switzerland
Life Fitness Europe GMBH
Siemensstrasse 3
85716 Unterschleissheim
GERMANY
Telephone: (+49) 89.31 77 51.0 (Germany)
(+41) 0848 000 901 (Switzerland)
Fax: (+49) 89.31 77 51.99 (Germany)
(+41) 043 818 07 20 (Switzerland)
G5-001 Rev A
09/08
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|