ELX16-240
Installation Guide
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notice
1. Do not p lace heavy objects on the top of the ELX16-240.
2. ELX16-240 is for indoor use. It is not weatherproof. Use ELX16-240 with referring to its
environmental specifications (Temp erature & Humidity). To clean the ELX16-240, gently wipe the
outside with a clean dry cloth.
3. ELX16-240 uses AC power of 110V ~ 220V. Be cautious not to cause electric damages to ELX16-240.
4. Be careful not to drop the ELX16-240. Physical shocks may harm the product. In addition, be sure the
ELX16-240 is secured after installation.
5. ELX16-240 is made of metal. Therefore you can hurt human beings if yu throw it to them or hit on
them. When installing ELX16-240 , be cautious to locate on safe places where children are unreachable.
6. If ELX16-240 does not operate properly, please contact the closest Rugged CCTV. distributor for after
sales service. Tampering or disassembling the product will void the warranty.
7. Security surveillance laws may differ for each country. Therefore, please contact the local region first
to avoid any surveillance law violations .
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
Contents
Contents
OVERVIEW ..................................................................................................................................................................7
1. What is ELX16-240?.................................................................................................................................... 7
2. Supplied Accessories ..................................................................................................................................8
3. Description & Function ................................................................................................................................9
INSTALLATION AND CONNECTION..............................................................................................................11
4. Connecting & Running ..............................................................................................................................11
4.1. Connecting camera...........................................................................................................................11
4.2. Connecting Monitor .......................................................................................................................... 12
4.3. Connecting Audio..............................................................................................................................12
4.4. Supplying Power ............................................................................................................................... 13
5. Running OSD menu .................................................................................................................................. 14
5.1. Using menu .........................................................................................................................................14
5.2. Dialogue Box to Edit a Word .........................................................................................................15
6. Setting remote controller .........................................................................................................................16
6.1. Setting ID of ELX16-240................................................................................................................. 16
6.2. Selecting ELX16-240....................................................................................................................... 17
6.3. Operable range of remote controller .......................................................................................... 17
6.4. Loading the batteries into remote controller............................................................................ 17
7. ELX16-240 Configuration........................................................................................................................18
7.1. Basic Configuration .......................................................................................................................... 18
7.2. Advanced Configuration ................................................................................................................. 18
7.3. External Storage & Backup Configuration ................................................................................ 19
7.4. Internet/Intranet Configuration ...................................................................................................... 19
8.
ELX16-240 Basic Setting ...................................................................................................................... 20
8.1. Viewing Image .................................................................................................................................... 20
8.2. Setting Date & Time.........................................................................................................................21
8.2.1.
8.2.2.
8.2.3.
8.2.4.
8.2.5.
8.2.6.
Time Zone...................................................................................................................................21
Daylight Saving.........................................................................................................................21
Sync with NTP........................................................................................................................... 21
Time Format............................................................................................................................... 22
Date............................................................................................................................................... 22
Time..............................................................................................................................................22
Error! Unknown document property name.
Rugged CCTV
4
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
ELX16-240
8.2.7.
Apply Date/Time ....................................................................................................................... 22
8.3. Setting Recording Condition .........................................................................................................23
8.3.1.
8.3.2.
8.3.3.
8.3.4.
8.3.5.
8.3.6.
8.3.7.
Configuration Status................................................................................................................ 23
Channel Status.......................................................................................................................... 24
Recording Speed/Quality....................................................................................................... 24
Speed(ips).................................................................................................................................. 24
Quality.......................................................................................................................................... 24
Audio Recording....................................................................................................................... 24
Apply.............................................................................................................................................24
9. Connecting and Configuring DIO Ports ..............................................................................................25
9.1. Connecting and Configuring Sensor .......................................................................................... 26
9.1.1.
9.1.2.
9.1.3.
Specification............................................................................................................................... 26
Connecting Sensor Input....................................................................................................... 26
Configuring Sensor at OSD menu...................................................................................... 27
9.2. Connecting & Configuring Relay Out.........................................................................................29
9.2.1.
9.2.2.
9.2.3.
Specifications .............................................................................................................................29
Connecting Relay Out............................................................................................................ 29
Configuring Relay Out at OSD menu................................................................................ 30
9.3. Connecting Serial Port .................................................................................................................... 31
9.3.1.
9.3.2.
9.3.3.
9.3.4.
Configuring Serial Ports for Pan/Tilt/Zoom ...................................................................... 31
Diagrams of serial ports .........................................................................................................32
View of COM3/COM4 Serial Ports ..................................................................................... 33
Configuring COM Port at OSD menu................................................................................ 34
9.4. Connecting External Device with Serial Port........................................................................... 35
9.4.1.
9.4.2.
9.4.3.
Connecting Text Input Device (ATM / POS / Access Control) .................................. 35
Configuring Serial Setup (COM1) at OSD menu........................................................... 35
Configuring Text ........................................................................................................................36
9.5. Connecting USB Device................................................................................................................. 37
9.6. Connecting Video In/Output.......................................................................................................... 38
10.
Connecting External Storage............................................................................................................ 39
10.1.
IEEE1394 Port ............................................................................................................................... 39
Connecting IEEE1394 Device.................................................................................................. 39
Available HDD ............................................................................................................................... 40
Registering & Formatting HDD ................................................................................................ 40
10.2.
10.3.
10.4.
Error! Unknown document property name.
Rugged CCTV
5
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
Contents
11.
11.1.
11.2.
Network Monitoring & Managing...................................................................................................... 42
Connecting Ethernet.................................................................................................................... 42
Configuring ELX16-240’s Network Information .................................................................. 43
12.
12.1.
12.2.
Using DVR manager.............................................................................................................................44
PC System Requirements for running DVR manager ..................................................... 44
Installing DVR manager .............................................................................................................44
Uninstalling DVR manager ........................................................................................................46
Configstation.................................................................................................................................. 46
Monitor..............................................................................................................................................47
Playback .......................................................................................................................................... 47
12.3.
12.4.
12.5.
12.6.
APPENDIX ..............................................................................................................................................................48
#1.
#1.1.
#1.2.
HDD............................................................................................................................................................ 49
Fundamental Notions & Terms................................................................................................. 49
Installing HDD ................................................................................................................................ 51
Replacing HDD..............................................................................................................................62
Keeping Data ................................................................................................................................. 63
Caution in using HDD.................................................................................................................. 64
#1.3.
#1.4.
#1.5.
#2.
#3.
#4.
How to Change Video Type ............................................................................................................... 65
Using CD-ROM...................................................................................................................................... 66
Specification............................................................................................................................................ 67
Error! Unknown document property name.
Rugged CCTV
6
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW
ELX16-240
OVERVIEW
1. What is ELX16-240?
The ELX16-240 is an 16-analog channels network digital video recorder. Video, Audio, and Text
Event -Logs are digitized and stored on two internal hard-drives.
q
q
q
q
q
16 analog video channels
1 channel audio recording & playback
Max. 240 / 200 ips (NTSC / PAL) recording speed
Realtime (30 / 25 ips for each channel) monitoring
Built-in software multiplexer for all 16 live monitoring channels (1 / 4 / 9 / 13 / 16 Ch Mode on
CCTV Monitor as well as PC)
q
q
q
q
q
q
q
q
q
q
q
Maximum 4TB storage capacity (IEEE 1394 for external HDD)
ATM/POS transaction information text recording and search with corresponding video
16 sensor inputs and 4 relay outputs
Built-in hardware motion detection with search function (64-division comparison)
Various efficient back-up methods (IEEE 1394(FiWi), Ethernet)
PTZ Control (Preset support) via RS 232 and RS 485/RS422
User-friendly 32bit True-colored Graphic OSD Menu
Dynamic IP (DHCP, Floating IP) support
IR remote controller (User controls PTZ with remote controller)
Management Software over Netw ork (DVR manager)
Dual CCTV monitor support (1 Normal, 1 Spot)
Error! Unknown document property name.
Rugged CCTV
7
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
OVERVIEW
2. Supplied Accessories
Unpack and check all the items as below.
1. ELX16-240 (1EA)
2. AC Power Cord (1EA)
3. CD-ROM (Including DVR manager) (1EA)
4. Remote Controller (1EA)
6. HDD Fixing KIT (1SET)
8. HDD EARTH CABLE (1EA)
5. Guide (2EA)
7. 19” RACK FIXING KIT (1SET)
Error! Unknown document property name.
(v 1.0)
8
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
OVERVIEW
ELX16-240
9. HDD DATA CABLE (1EA)
3. Description & Function
ELX16-240 Front
(1) Power switch
(2) Function buttons
(3) LED
(4) I/O Port cover
(5) USB connector
(6) IEEE1394 connector
(7) Remote controller receiver
Error! Unknown document property name.
Rugged CCTV
9
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
OVERVIEW
ELX16-240 Rear
(8) BNC connector for video input
(9) AC power connector
(10) BNC connector for video output
(11) BNC connector for monitor A output
(12) BNC connector for monitor B output
(13) Terminal block for sensor, relay, and serial input/output
(14) IEEE1394 connecter
(15) Terminal block for RS232 & 422/485
(16) Ethernet connector
(17) GND
(18) RS232 connecter (9Pin D-Sub)
(19) Audio input / output connector
(20) S-VHS connector
Error! Unknown document property name.
(v 1.0)
10
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
INSTALLATION AND CONNECTION
4. Connecting & Running
4.1. Connecting camera
(1) Connect CCTV camera to ELX16-240 with BNC cable as shown below.
1. The video type for all channels should be either NTSC or PAL
2. ELX16-240 sets video signal’s impedance ( 75Ù) automatically.
Impedance is set as 75Ù basically. If connecting a device to video output, impedance will be “Hi-z”
status.
3. Video type (NTSC/PAL) should be changed after disassembling ELX16-240.
So in order to change video type, it is recommended to contact the cloest local Rugged CCTV.
distributor. When changing it, refer to “Appendix #2. Changing Video Type ”. Rugged CCTV. is not
responsible for any service warranty about a problemdue to careless change.
Error! Unknown document property name.
Rugged CCTV
11
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
4.2. Connecting Monitor
(1) Connect CCTV monitor to ELX16-240 with BNC cable as shown below.
ELX16-240 has two monitor output ports ; for A(Normal) and B(Spot). When connecting only one
monitor, use monitor A.
4.3. Connecting Audio
(1) Connect audio signal to ELX16-240 with using RCA cable.
Error! Unknown document property name.
12
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
4.4. Supplying Power
(1) Connect power cable.
1. When supplying power, ELX16-240 starts booting
automatically.
2. When pressing the power switch during 5 seconds, a
dialogue for entering admin password occurs. In order to
cut off power, key in the password.
3. For supplying power again, push the power switch.
Error! Unknown document property name.
Rugged CCTV
13
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
5. Running OSD menu
5.1. Using menu
Press the [MENU] button to open the OSD Configuration Menu.
(1) Main Menu
(2) Sub-menu
(3) Setting Page
(1) Main Menu Tabs: The select ed tab is shown in blue and the related sub-menus will be shown below
the tab. To move to the previous/next Main Menu Tab, use the [
sub-menu, press the [ENTER] or [ ] buttons.
/
] arrow buttons. To move to a
(2) Sub-menu: The select ed sub -menu is shown in blue and the related setting page will be shown to the
right of the sub-menu. Use the [ / ] arrow button s to move within the sub-menu list. To move to the
setting page press the [ENTER] button. To exit the setting page, press the [EXIT] button.
(3) Setting Page : The select ed item is shown in gray. To move within each page, use the [
/
] or
[ / ] arrow buttons. Press the [ENTER] button to change the value of a setting. When the setting value is
a word, a dialogue box to edit the word will open. When setting value is a number, it should be set with
using the [
/
] or [ / ] arrow buttons. After the value is set, press the [EXIT] button. To exit the
Setting Page, press the [EXIT] button.
(4) Help message : Related information for each menu/setting will be displayed here.
Error! Unknown document property name.
14
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
5.2. Dialogue Box to Edit a Word
There are two methods to set word.
(1) Using number button
“ ”
Enter the related numbers in order of horizontal/vertical . (For example, in order to select C , press [3]
and [2] buttons.)
(2) Using arrow button
Select a value using the [
/
] or [ / ] buttons. The intersection of the horizontal and vertical bar
is select ed value. Press the [ ] button to confirm the selected value.
(3) Function word
The following symbols are for executing specific functions:
ü
: Enter
: Back Space & delete
: Space
: Move to left
: Move to right
: Previous Code Page
: Next Code Page
Error! Unknown document property name.
Rugged CCTV
15
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
6. Setting remote controller
6.1. Setting ID of ELX16-240
When controlling several DVRs with one remote controller, set Remote Control ID as follows.
(1) Press the [MENU] button.
(2) Select “System” with using [
] button and press the [ENETR] or [ ] button.
(3) Select “Miscellaneous” from the sub-menu list using the [ ] button and press the [ENETR] button.
(4) Select “Remote Control ID,” and press the [ENETR] button.
(5) Select a value using the [
/
] buttons and pressthe [EXIT] button.
(6) Press the [EXIT] button toexit the Settings Page and return to Monitor mode.
Up to 16 DVRs can be controlled with a single remote controller.
When not using remote controller, set the Remote Control ID as “Off”.
Error! Unknown document property name.
16
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
6.2. Selecting ELX16-240
If several DVRs are set with unique ID numbers, they can be controlled with one remote controller. To
select a specific (ELX16-240), keep pressing the ID button of remote controller until a buzzer sounds
during 2 seconds.
Because remote controller ID is sixteen, DVR will correspond until pressing ID button sixteen times.
6.3. Operable range of remote controller
6.4. Loading the batteries into remote controller
Remote controller requires two AAA-type batteries.
2. Taking care that the poles(+/-)
1. Remove the battery cover.
3. Replace the battery cover.
are correctly positioned.
Batteries are not included as a packing accessory.
Error! Unknown document property name.
(v 1.0)
Rugged CCTV
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
7. ELX16-240 Configuration
7.1. Basic Configuration
7.2. Advanced Configuration
Error! Unknown document property name.
(v 1.0)
18
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
7.3. External Storage & Backup Configuration
7.4. Internet/Intranet Configuration
Error! Unknown document property name.
Rugged CCTV
19
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
8. ELX16-240 Basic Setting
8.1. Viewing Image
After initial start-up, images are displayed in multi-split screen according to the connected channels. The
following example is when 4 channels are connected.
If user password is set, a prompt for entering the password will appear.
Error! Unknown document property name.
20
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
8.2. Setting Date & Time
(1) Press [MENU] button, and select “Quick Setup ” tab.
(2) Select “Date/Time” and enter the Settings Page by pressing [ENTER].
8.2.1. Time Zone
(1) Select “Time Zone” and press [ENETR] button to configure.
(2) Select a value usingthe [
/
] button and press the [EXIT] button when finished.
8.2.2. Daylight Saving
(1) “Daylight Saving Time” is only activated for time zones that use Daylight Savings. If activated, press
[ENTER] to enter a new value.
(2) Select “On/Off” using the [
/
] button and press the [EXIT] button when finished.
8.2.3. Sync with NTP
In order to synchronize time with NTP (Network Time Protocol) server, select “On”.
(1) Select “Sync with NTP ” using the [ ] or the [ / ] buttons and press [ENTER] button.
/
(2) Select “On/Off” using the [
/
] button and press the [EXIT] button.
Error! Unknown document property name.
Rugged CCTV
21
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
8.2.4. Time Format
(1) Select “Time Format” using the [
/
] or the [ / ] buttons and press [ENTER].
(2) Two Time Formats are available; ‘MM/DD/YYYY’ and ‘YYYY/MM/DD’. Select a value using [ / ]
buttons, and press the [EXIT] button when finished. (Default value is ‘MM/DD/YYYY’.)
8.2.5. Date
(1) Select “Date” using the [
/
] or the [ / ] buttons and press [ENTER].
] buttons, and select t he value using the [ / ]
(2) Select ‘MM’/‘DD’/‘YYYY’ using the [
buttons.
/
(3) Press the [EXIT] button when finished.
8.2.6. Time
(1) Select “Time” using the [
/
] or the [ / ] buttons and press [ENTER].
(2) Select ‘HH’/‘MM’ using the [
/
] buttons, and select t he value usingthe [ / ] buttons.
(3) Press the [EXIT] button when finished.
8.2.7. Apply Date/Time
Most setting values are applied automatically, when exiting from the related menu page. But “Date”
& “Time” settings are not applied automatically because theymay critically affect the file system of
the recorded HDD. To apply Date/Time setting s confirm settings with [Apply Date/Time] button.
(1) Select “Apply Date/time” using the [
message will appear.
/
] or the [ / ] buttons and press [ENTER]. A warning
(2) Select “OK” using the [
[EXIT] button.
/
] or the [ / ] buttons and press [ENTER]. To cancel, press the
Error! Unknown document property name.
Rugged CCTV
22
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
8.3. Setting Recording Condition
Recording conditions under the “Quick Setup ” menu tab apply the same values to all analog channels
1~16. All settings are applied for 24 hours/day regardless of the values set for “Time Schedule” or
“Alarm Rec. ”
(1) Press [MENU] button, and select “Quick Setup .”
(2) Move to sub-menu by pressing [ENTER] orthe [ ] button.
(3) Select “Recording” using the [ / ] buttons and pressthe [ENTER] button.
8.3.1. Configuration Status
Displays the recording configuration status. When setting up through the “Quick Setup ” menu, “Quick
Setup” will be shown. When setting up through “Normal Rec. ” or “Alarm Rec.,” “Custom Setup” will be
shown.
Only when all the 16 channels' normal recording conditions are set through M' acro Setup' and
maintained, it is marked as 'Macro Setup'. Otherwise, it will be marked as 'Custom Setup '.
Error! Unknown document property name.
Rugged CCTV
23
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
8.3.2. Channel Status
(1) Select “Channel Status ” using [ / ] buttons and press the [ENTER] button.
(2) Select a value using the [ ] button. Press the [EXIT] button when finished.
/
8.3.3. Recording Speed/Quality
(1) Select “Recording Speed/Quality” using [ / ] buttons and pressthe [ENTER] button.
(2) Select a value using the [ ] button. Press the [EXIT] button when finished.
/
Low : Speed=1ips and Quality=Q5
Std. : Speed=5ips and Quality=Q5
High : Speed=15ips and Quality=Q5
Custom : Speed and Quality = Manually defined by User.
8.3.4. Speed(ips)
When “Recording Speed/Quality” is set as “Custom,” values can be set manually.
(1) Select “Speed ” using [ / ] buttons and press the [ENTER] button.
(2) Select a value using the [
/
] button. Press the [EXIT] button when finished.
8.3.5. Quality
When “Recording Speed/Quality” is set as “Custom,” values can be set manually.
(1) Select “Quality” using [ / ] buttons and press the [ENTER] button.
(2) Select a value using the [
/
] button. Press the [EXIT] button when finished.
8.3.6. Audio Recording
(1) Select “Audio Recording” using [ / ] buttons and pressthe [ENTER] button.
(2) Select a value using the [
/
] button. Press the [EXIT] button when finished.
8.3.7. Apply
(1) Select “Apply ” using [ / ] buttons and press the [ENTER] button.
(2) Setting values are applied and the previous menu will be displayed.
Error! Unknown document property name.
24
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
9. Connecting and Configuring DIO Ports
Trimming Wire
When connect ing awire to a terminal block, follow the instructions below. Note the different types of
wire that can be used.
Stranded Wire: Peel off the wiring cover
8~10mm and solder it. Wire gage should be
AWG 22 ~ 26.
Solid Wire: Peel off the wiring cover 8~10mm
and solder it. Wire gage should be AWG 20 ~
26.
Inserting & removing wire
To insert the wire, use a screwdriver as
shown in the diagram to the right.
Error! Unknown document property name.
Rugged CCTV
25
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
9.1. Connecting and Configuring Sensor
9.1.1. Specification
In order to run sensor input of ELX16-240 series normally, the following conditions are required.
Input Ch.
16Ch. Photo coupler inputs
Input type
N.C. (Normal Close) / N.O. (Normal Open) type
Dry contact
Spec.
Supported sensor
Connecting
Connecting the t rimmed wire to terminal block
Available input pulse Min. 500ms
range
Performance
Output current
Typical DC 12mA
9.1.2. Connecting Sensor Input
Connect S1 ~ S16 with referring t o the followings. It shows to connect a dry contact. When connecting a
non-dry contact type of sensor ( e.g. Open collector output) please contact Customer Support team.
Error! Unknown document property name.
26
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
9.1.3. Configuring Sensor at OSD menu
(1) Press the [Menu] button, and select the “Alarm Source ” among OSD menus.
(2) Select “Sensor” menu and press the [Enter] button for moving to the sub-menu.
9.1.3.1. Global
It is for setting 16 sensors simultaneously. It has three types; Off / Normal Open (N.O.) / Normal Close
(N.C.)
(1) Select “Global” and set a type.
(2) Press the “Apply ” button in order to confirm the setting value.
9.1.3.2. Configuration
It is for setting 16 sensors separately. Select and set each sensor.
(1) Select “Configuration” and press the [Enter] button.
(2) Select a sensor (S1 ~ S16) and set its type.
(3) Press the [Exit] button after setting.
Error! Unknown document property name.
Rugged CCTV
27
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
1. This menu is to set sensor using and sensor type. However recording by sensor input and relay output
should be set in another menu.
2. For recording setting by sensor input, refer to the “Alarm Rec.” part of “ ELX16-240 User’s Guide”,
and for relay output, refer to the “Alarm Act.” part.
Error! Unknown document property name.
28
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
9.2. Connecting & Configuring Relay Out
9.2.1. Specifications
In order to run relay output of ELX16-240 series normally, the following conditions are required .
Output Ch.
Output type
Connecting type
DC
4Ch. Rrelay differential outputs
Dry Contact
Spec.
Connecting the trimmed wire to terminal block
24V DC, 1.25A, 30W
125V DC, 0.24A, 30W
125V AC, 0.5A, 62.5VA
Rating
AC
9.2.2. Connecting Relay Out
Connect R1 ~ R4 with referring t o the followings. It shows to connect a warning light.
Error! Unknown document property name.
Rugged CCTV
29
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
9.2.3. Configuring Relay Out at OSD menu
Relay can run by sensor or MD, and its condition can be set differently according to schedule. When
using the [Relay] button + [Number] button on the front panel or Manager S/W, relay can be operated
from remote site.
For detailed information for setting, please refer to “ ELX16-240 User’s Guide”.
Error! Unknown document property name.
30
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
9.3. Connecting Serial Port
9.3.1. Configuring Serial Ports for Pan/Tilt/Zoom
The ELX16-240 series have most major PTZ protocols already pre-programmed. Makes and models not
supported can still be controlled using the Transparent Protocol. For a list of supported protocols, refer to
the list on the OSD Configuration menu.
The following figure shows how to connect PTZ camera to RS485 (COM2). When using another serial
port, connect it with referring to each connection diagram below.
Error! Unknown document property name.
Rugged CCTV
31
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
9.3.2. Diagrams of serial ports
9.3.2.1. Diagram of COM1
9.3.2.2. Diagram of COM2
Error! Unknown document property name.
(v 1.0)
32
Rugged CCTV
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CO NNECTION
ELX16-240
9.3.2.3. Diagram of COM3
9.3.2.4. Diagram of COM4
9.3.3. View of COM3/COM4 Serial Ports
Error! Unknown document property name.
Rugged CCTV
33
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
9.3.4. Configuring COM Port at OSD menu
Configure PTZ COM ports and available modes at “System / Serial Setup ”.
After completing serial setup, configure base address and port for each channel under the “Camera” menu
tab . When connecting PTZ devices to several cameras, be sure the base address matches the address for
the camera.
Error! Unknown document property name.
34
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
9.4. Connecting External Device with Serial Port
9.4.1. Connecting Text Input Device (ATM / POS / Access Control)
In addition to images, the ELX16-240 can record text data received from POS/ATM through the
COM1/RS232 serial port.
Connect to COM1/RS232 (9pin D-Sub) of ELX16-240, and configure the “Serial Setup ” sub-menu under
the “System” tab and “Text” sub-menu under the “Alarm Source” tab.
9.4.2. Configuring Serial Setup (COM1) at OSD menu
(1) Set the “System” in OSD menus, and move to “Serial Setup ” menu.
(2) Select COM1 in “Serial Setup ”, set Device as “Text ”.
(3) Set Baud Rate/Parity/Stop bit/Data bit with referring to manual of the connected external device.
Error! Unknown document property name.
Rugged CCTV
35
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
9.4.3. Configuring Text
(1) Select the “Alarm Source” menu among OSD menus.
(2) Select the “Text ”, and set each value.
Before installing any external device, consult with the local distributor. Some external devices may not
be compatible with the DVR.
Error! Unknown document property name.
36
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
9.5. Connecting USB Device
USB port can be used to copy up to 1 minute of images to aUSB Flash memory disk. When connecting
USB device, do not exceed the rated values of USB device.
USB Spec.
Available Device
Output Voltage/Current
Ver 1.1 (Max 12M bps)
USB Memory Stick,
Max. 200mA per DC 5V / Port
The disk should be formatted with FAT32 type.
If properly connected, the disk is recognized automatically as in the following picture. To copy images,
the process is as follows: Set copy range (up to 1 minute) à Select drive à Copy (press “Start”) .
Error! Unknown document property name.
Rugged CCTV
37
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
1. USB Flash products that require a Windows program to operate may not be recognized by the DVR.
2. For more information about copy function, refer to the “ ELX16-240 User’s Guide”.
9.6. Connecting Video In/Output
DVR's video in/output is composed of loop through. DVR recognizes the connection status and video
impedance automatically.
Ù
For example, when DVR is connected by only video input, the video impedance is set as 75 . And when
video in/output is connected simultaneously, the video impedance is changed as Hi-z. So in this case,
Ù
video impedance of external video input device(e.g CCTV monitor) should be set as 75 .
Error! Unknown document property name.
38
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
10. Connecting External Storage
10.1. IEEE1394 Port
ELX16-240 series have two IEEE1394 ports for external storage device interface. With them, ELX16-240
series can expand storage capacity up to 4TB.
Some IEEE1394 Bay may not be recognized by the ELX16-240 series . Before purchasing, consult the
local distributor.
10.2. Connecting IEEE1394 Device
When using FireWire supported external HDD, hard drive bays can be connected to 1 port in the front
panel or 1 port in the rear panel. The ELX16-240 series does not supply power to the hard drive bay;
therefore only bays that use externalpower can be used.
ELX16-240 series detect external HDD, even though ELX16-240 series run. If not, it is recommended
to connect as follows.
1. Power off ELX16-240.
2. Connect external HDD to IEEE1394 port.
3. Power on external device.
4. Power on ELX16-240.
Error! Unknown document property name.
Rugged CCTV
39
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
10.3. Available HDD
It is recommended to use the following HDD models with the ELX16-240. If a non-recommended HDD
is used, Rugged CCTV. will not guarantee the warranty.
Manufacturer : MAXTOR
Series
Model No
6Y060L0
Siz e
60GB
Series
Model No
Size
60GB
4R060L0
4R080L0
4R120L0
6Y080L(P)0
6Y120L(P)0
80GB
80GB
DiamondMax
Plus 9
DiamondMax
16
120GB
120GB
6Y160L(P)0
6Y200P0
160GB
200GB
250GB
4R160L0
160GB
(7200rpm)
(5400rpm)
6Y2 50P0
Buffer for DiamondMax Plus 9 ’s model “L” is 3MB; for model “P” the buffer is 8MB.
10.4. Registering & Formatting HDD
“Disk Manager” will automatically run on start-up after installing a HDD.
If “Disk Manager” does not automatically run on start-up, make sure the HDD is properly installed.
Error! Unknown document property name.
40
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
(1) Press [ENTER] button at “Select Disk”.
(2) Select new added HDD (indicated as “[F] ”) using [ / ] button and press [EXIT] button
(3) Select “Action” using [ / ] button and press [EXIT] button.
(4) Select “Add” using [
/
] button and press [EXIT] button.
(5) Select “Apply ” using [ / ] button and press [EXIT] button. The HDD status is changed to “[*] ”.
(6) Select “Action” using [ / ] button and press [EXIT] button.
(7) Select “Format ” using [
/
] button and press [EXIT] button.
(8) Select “Apply” using [ / ] button and press [EXIT] button. The HDD status is changed to “[R]”
after formatting.
(9) Shut down “Disk Manager” by pressing [EXIT] button.
Error! Unknown document property name.
Rugged CCTV
41
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
11. Network Monitoring & Managing
ELX16-240 can be accessed, controlled, and managedfrom remote site via Internet/Intranet.
11.1. Connecting Ethernet
(1) Turn off ELX16-240’s power switch.
(2) Connect ELX16-240 to hub with Ethernet cable.
(3) Turn on ELX16-240 ’s power switch.
1. Supply power to ELX16-240 after connecting Ethernet cable to protect against electrical damage to
ELX16-240.
2. Check cable connection status.
3. Check LED on ELX16-240’s rear panel after supplying power.
Error! Unknown document property name.
42
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
11.2. Configuring ELX16-240’s Network Information
The following description is on based on Ethernet connection. For more detailed ni formation on the
Network Settings Page, please refer to “ ELX16-240 OSD User’s Guide”.
(1) Press [MENU] button.
(2) Select “System” using the [
/
] buttons and press [ENTER].
(3) Select “Network” using the [ / ] buttons and press [ENTER].
(4) Select “IP Addr” using the [ / ] buttons and press [ENTER].
(5) Press [EXIT] button after entering IP address in the dialogue box.
(6) Select “Net Mask” using the [ / ] buttons and press [ENTER].
(7) Press [EXIT] button after entering Net Mask in the dialogue box.
(8) Select “Gateway ” using the [ / ] buttons and press [ENTER].
(9) Press [EXIT] button after entering Gateway in the dialogue box.
(10) Select “DNS” using the [ / ] buttons and press [ENTER].
(11) Press [EXIT] button after entering DNS in the dialogue box.
(12) Press [EXIT] button to exit the page.
Error! Unknown document property name.
Rugged CCTV
43
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
12. Using DVR manager
12.1. PC System Requirements for running DVR manager
Minimal Requirements
P- 600MHz or above
128 MB or above
Recommended Requirements
CPU
RAM
VGA
OS
P- 1GHz or above
256 MB or above
32 MB or above
16 MB or above
Windows 2000/XP
Windows 2000/XP
Resolution
Network
1024 X 768 pixels or above
100 Base TX Fast Ethernet
1024 X 768 pixels or above
100 Base TX Fast Ethernet
12.2. Installing DVR manager
(1) Insert Setup CD-ROM into CD-ROM drive of administrator’s PC
(2) Doubleclick the DVR manager setup file. Install Shield Wizard will be automatically installed.
(3) Click the “I Agree” button to accept the license agreement
Error! Unknown document property name.
44
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
(4) Select which component s to install and press the “Next ” button.
(5) Browse and choose a directory if the default directory is not preferred. Click the “Install” button,
after selecting a directory to install.
(6) Click the “Close” button after DVR manager program is installed successfully.
Error! Unknown document property name.
Rugged CCTV
45
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
INSTALLATION AND CONNECTION
12.3. Uninstalling DVR manager
(1) Click Windows “Start” Button.
(2) Select and Click‘Uninstall’ icon to run Uninstall Shield.
(3) DVR manager program will be automatically deleted.
12.4. Configstation
Click icon on desktop to run “DVR manager Configstation” program.
Error! Unknown document property name.
46
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION AND CONNECTION
ELX16-240
12.5. Monitor
Click the related icon and run the “DVR manager Monitor” program.
12.6. Playback
Click the related icon and run the “DVR manager Playback” program.
Error! Unknown document property name.
Rugged CCTV
47
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
APPENDIX
APPENDIX
Error! Unknown document property name.
48
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
#1. HDD
#1.1. Fundamental Notions & Terms
DVR Storing Constructure (VFS2)
DVR series has a peculiar storing constructure, and its features are as follows.
(1) It is possible to connect 2 sets of HDD internally (Internal, ATA Interface) and 63 sets of HDD
externally (External, 2 ports of IEEE1394).
(2) All of the connected HDDs is recognized as one virtual disk, and DVR supports upto 4TB.
(3) Hdds are divided into primary disk (connected firstly) and auxillary disk.
ATA(or EIDE) supports two channel interfaces (Primary/Secondary). Each channel can be connected to
two devices (Master/Slave, HDD/CD-ROM). However DVR supports 1 channel interface internally and
total two HDDs. In order to prevent confusing VFS2 ’s Primary Disk, we will not use the terms
(Primary/Secondary).
(4) Primary disk is composed of log partition, normal partition, and alarm partition, and auxillary disk is
composed of only normal partition. So if primary disk has some problem, all of the recorded data will
be lost.
<Note>
Log Partition
To store the information of recorded data
Normal Partition
Alarm Partition
To store the data as normal recording schedule
To store the data as alarm recording condition (MD or Sensor)
Error! Unknown document property name.
Rugged CCTV
49
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
Backup
(1) Backup is possible only through IEEE1394 port, and HDD for backup should be formatted as FAT32
type. (Its type is indicated as [F] in Disk Manager.)
Disk Manager
(1) When HDD is added or deleted physically, Disk Manager runs automatically after rebooting. If not,
you can run “Disk Manager” manually with moving “MenuàUtilityàDisk Manager”.
(2) HDD Type at Disk Manager
[R]
Available of recording
[V]
Connected and formatted as ELX16-240’s file system. If using ‘Add used’ command, it
will be changed to [R]. There is no need to reformat.
Connected but not available file system. After using ‘Add’, need to format for making as
[R].
[F]
[*]
[X]
Connected and added using the ‘ADD’ command. If formatting, it will be [R].
If there is a disk of [*], DVR will record nothing.
HDD cable is not connected or has some problem. In case of that, HDD should be
removed with using ‘Confirm Removed’ menu.
IntA
IntB
Internal Master HDD
Internal Slave HDD
Ext
External HDD
Error! Unknown document property name.
Rugged CCTV
50
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
(3) HDD Managing Command
Format
Add
Format as ELX16-240’s file system. Not available to PC file system.
Add HDD for recording. Need to format.
Add Used
Add a HDD that has been used and formatted. There is no need to reformat . It is
possble only when HDD is added as Primary Disk.
Remove
Remove current HDD. HDD can be reused without data loss by the ‘Add Used ’
command.
Confirm Removed
Used when a removed HDD is still listed. ALL DATA WILL BE LOST!
#1.2. Installing HDD
Compatible HDD
It is recommended to use the following HDD models with the ELX16-240. If a non-recommended HDD
is used, Rugged CCTV. will not guarantee the warranty.
Manufacturer : MAXTOR
Series
Model No.
6Y060L0
Size
Series
Model No.
4R060L0
4R080L0
4R120L0
4R160L0
Size
60GB
80GB
120GB
160GB
60GB
80GB
120GB
160GB
6Y080L(P)0
6Y120L(P)0
6Y160L(P)0
DiamondMax
Plus 9
DiamondMax
16
(7200rpm)
(5400rpm)
6Y200P0
6Y250P0
200GB
250GB
L series of DiamondMax Plus 9 has 2MB buffer memory, while P model has 8MB
Error! Unknown document property name.
Rugged CCTV
51
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
Installing & Expanding Internal HDD
Adding or replacing HDD should follow below process.
(1) Turn off the power of ELX16-240.
(2) Check whether the dip switches are set as illustrated below.
(3) Remove the 6 screws as illustrated below and pull up the cover from the rear part to open.
Error! Unknown document property name.
52
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
(4) Take out power and data cable of HDD from Main PCB ASS’Y. Remove 4 HDD Bracket screws and
take out HDD ASS’Y.
(5) Fix the HDD into HDD Bracket with provided screws. Assemble an earth cable with HDD.
Error! Unknown document property name.
Rugged CCTV
53
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
(6) Assemble cables according to the following numbers.
The supplied HDD cables have two kinds of colors. When connecting to PCB Ass’y, use blue cable.
(7) Fix the assembled HDD and earth cable into case with screws.
(8) Assemble the top cover.
1. Replacing ‘SLAVE’ HDD of internal 2 HDDs causes permanent data loss in the SLAVE HDD.
2. MASTER HDD has all the index of stored data including ‘SLAVE’ HDD. Corruption on
‘MASTER’ HDD may cause total data loss. Be careful when h andling the main HDD.
3. It is strongly recommended that all data within HDDs should be backed up before replacing.
Error! Unknown document property name.
54
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
When installing one primary disk
(1) When power is supplied to ELX16-240, “Disk Manager” runs automatically after rebooting. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) There is a HDD that is indicated as “[F] IntA”. Select it.
(3) Press the “Apply ” button after selecting action as “Add”. Then [F] is changed to [*].
(4) Press the “Apply ” button after selecting action as “Format ” and setting the size of alarm partition.
Then [*] is changed to [R].
Note
Alarm partition can be set from 10% to 90% within the size of primary disk.
(5) Press the [EXIT] button to shut down “Disk Manager”. (If recording schedule is set, ELX16-240 will
start recording.)
Error! Unknown document property name.
Rugged CCTV
55
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
When installing one primary disk and auxiliary disk
(1) When power is supplied to ELX16-240, “Disk Manager” runs automatically after rebooting. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) There is a HDD that is indicated as “[F] IntA”.
(3) Select a HDD for installing as primary disk. (IntA or IntB)
(3) Press the “Apply ” button after selecting act ion as “Add”. Then [F] is changed to [*]. If IntB is added
as primary disk, it will be placed at upper list.
(5) Select a HDD for installing as auxiliary disk.
(6) Press the “Apply ” button after selecting action as “Add”. Then [F] is changed to [*].
(7) Select a primary disk, and press the “Apply ” button after selecting action as “Format” and setting the
size of alarm partition. Then [*] is changed to [R].
(8) Select an auxiliary disk, and press the “Apply ” button after selecting action as “Format” and setting
the size of alarm partition. Then [*] is changed to [R].
Alarm partition can be set at only primary disk. So it is indicated as “Disable” in case of formatting.
(9) Press the [EXIT] button to shut down “Disk Manager”. (If recording schedule is set, ELX16-240 will
start recording.)
Error! Unknown document property name.
56
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
Expending External HDD (When using internal HDD as primary disk)
ELX16-240 use IEEE1394 as external storage device interface, and has two ports of IEEE1394. ELX16-
240 supports upto 4TB storage.
1. Some IEEE1394 ports may not be recognized by the ELX16-240. Before purchasing, consult the
local distributor.
2. External storage should use external power.
3. For connection and setup of IEEE1394, please refer to the manual of related device.
Connect IEEE1394 interface cable as follows.
Error! Unknown document property name.
Rugged CCTV
57
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
When using Disk Farm
The following description is when ELX16-240 has internal primary disk and 3 sets of IEEE1394 HDD.
(1) When external HDD farm is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
If connecting the device that is used in ELX16-240, type will be indicated as [V].
(3) Select a third HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(4) Select a fourth HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(5) Select a second HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
is changed to [R].
(6) Select a third HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*] is
changed to [R].
(7) Select a fourth HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*]
is changed to [R].
(8) Press the [EXIT] button to shut down “Disk Manager”.
Error! Unknown document property name.
58
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
When using RAID
The following description is when ELX16-240 has internal primary disk and 1 set of IEEE1394 HDD.
Even though several HDDs are connected to RAID, ELX16-240 will recognize them as only one HDD.
For connection and setup of RAID, please refer to the manual of related device.
(1) When external HDD RAID is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
If connecting the device that is used in ELX16-240, type will be indicated as [V].
(3) Select a second HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
is changed to [R].
(4) Press the [EXIT] button to shut down “Disk Manager”.
Error! Unknown document property name.
Rugged CCTV
59
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
Installing & Expending External HDD (When using external HDD as
primary disk)
When using Disk Farm
The following description is when ELX16-240 does’t have internal primary disk and 4 sets of IEEE1394
HDD.
(1) When external HDD farm is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) Select a first HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
It is when ExtA is added as primary disk.
If connecting the device that is used in ELX16-240, type will be indicated as [V].
(3) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(4) Select a third HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(5) Select a fourth HDD of [F] Ext . Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(6) Select a first HDD of [*] Ext . Press the “Apply ” button after selecting action as “Format ”. Then [*] is
changed to [R].
(7) Select a second HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
is change d to [R].
Error! Unknown document property name.
60
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
(8) Select a third HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*] is
changed to [R].
(9) Select a fourth HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format”. Then [*]
is changed to [R].
(10) Press the [EXIT] button to shut down “Disk Manager”.
When using RAID
The following description is when ELX16-240 does’t have internal primary disk and 2 sets of IEEE1394
HDD.
(1) When external HDD RAID is connected to IEEE1394 port, “Disk Manager” runs automatically. If not,
run it manually in “MenuàUtilityàDisk Manager”.
(2) Select a first HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
It is when ExtA is added as primary disk.
If connecting the device that is used in ELX16-240, type will be indicated as [V].
(3) Select a second HDD of [F] Ext. Press the “Apply ” button after selecting action as “Add”. Then [F] is
changed to [*].
(4) Select a first HDD of [*] Ext . Press the “Apply” button after selecting action as “Format ”. Then [*] is
changed to [R].
(5) Select a second HDD of [*] Ext. Press the “Apply ” button after selecting action as “Format ”. Then [*]
is changed to [R].
(6) Press the [EXIT] button to shut down “Disk Manager”.
Error! Unknown document property name.
Rugged CCTV
61
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
#1.3. Replacing HDD
Checking HDD
ELX16-240 file system (VFS2) sensors bad sector automatically, and the sensored bad sector is not used.
The following means when HDD is broken or has some problem in connection.
(1) When replaying is stopped or ELX16-240 is rebooted in specific playback range.
(2) When image searching per event is impossible.
(3) When recording is stopped and “Disk Manager” shows HDD type as [X].
When primary disk is broken
When primary disk is broken, all of the connected HDD data can’t be used. So the broken HDD should be
replaced and all connected HDDs should be reinstalled in “Disk Manager”. (“Remove” -> “Add” ->
“Format ”).
When auxiliary disk is broken
The broken auxiliary disk should be replaced and reinstalled in “Disk Manager”. (“Add” -> “Format ”).
Error! Unknown document property name.
62
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
#1.4. Keeping Data
To keep the stored data, you should back up or reserve as HDD itself.
Backup
(1) Connect backup HDD to IEEE1394 port.
(2) Go to playback mode with pressing the [Playback] button.
(3) Press the [SELECT] button and then [MENU] button.
(4) Run “Backup Manager” with selecting the “Backup Data” menu.
(5) Set backup range and press the “Start ” button after selecting backup HDD.
1. Backup HDD should be formatted as FAT32 type.
2. Backup data can be replayed wit h specific S/W, DVR manager or MiniPlayer.
3. Backup data is made as “*.re3” file. If file size is over 2GB, it may not be recognized normally.
4. In course of backup, “Auto Delete” function doesn’t run. If HDD is full, recording may be stopped
instantly.
5. For more detailed information of DVR manager’s backup, please refer to the “DVR manager User’s
Guide”.
Error! Unknown document property name.
Rugged CCTV
63
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
How to preserve as HDD itself
To keep HDD itself, it is possible only when HDD is installed and used in ELX16-240 (including primary
disk and RAID).
And it is recommended to use external HDD instead of internal HDD. Namely, connect only one external
HDD, and then keep it after data is full.
The preserved HDD’s data is possible to replaying only when it is connected to ELX16-240.
#1.5. Caution in using HDD
For handling or guaranteeing HDD, Rugged CCTV. follows HDD guaranty condition. Rugged CCTV.
doesn’t bear the responsibility about data loss by user’s mistake in operating.
Error! Unknown document property name.
64
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
#2. How to Change Video Type
In order to change video type of ELX16-240 series, jumper setting should be changed inside the case.
Jumper Setting
Video Type
NTSC Video
PAL Video
Remark
1-2
2-3
In order to change video type, contact the closest local Rugged CCTV. distributor. Rugged CCTV. is not
responsible for service warranty about user’s careless changing.
Error! Unknown document property name.
Rugged CCTV
65
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
#3. Using CD-ROM
Components of CD- ROM disc
Installation Guide
User’s Guide
:
:
ELX16-240 Installation Guide
ELX16-240 User’s Guide
: DVR manager User ’s Guide
(ELX16-240 Remote Management Program)
: Version 5.1
DVR manager
Acrobat Reader
Preparation
To read manual of CD-ROM disc, Adobe Acrobat 5.0 should be installed in client’s PC.
If Adobe Acrobat Reader is not installed within client’s PC, use the Acrobat Reader program of CD-
ROM.
Reading manual of CD-ROM
Follow the steps to read user’s guide.
(1) Insert the supplied CD-ROM into CD-ROM drive of PC.
Open the user’s guide, PDF file.
Error! Unknown document property name.
66
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
#4. Specification
General
CPU
32bit RISC Processor (200MIPS)
8MB
Flash Memory
Main Memory
OS
64MB
Embedded LINUX
Video Channel
Storage Device
16 Analog Channel
Internal 3.5” IDE HDD 2EA (default 1EA)
External 2EA for IEEE1394 Interface
Support Max. 4Tbytes
Intelligent File System
Data-loss protection against power failure
Image Compression
Technology
Differential Wavelet
1~5KB (Standard Quality)
5 Level
Average File Size
Image Quality Level
Image Compression Rate
Recording Speed
20:1~500:1
Max. 240ips in total at NTSC
Network
Browser
DVR manager
Protocol
TCP/IP, ARP, ICMP, DHCP, PPPoE
10/100Mbps Ethernet (RJ-45)
Firmware upgrade via Network
Monitoring : Max. 5 Users
Connector
S/W Upgrade
Simultaneous Users
Playback : Max. 5 Users
Security
Password (User or Administrator Authenticantion)
Error! Unknown document property name.
Rugged CCTV
67
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
Display
Monitoring
Max. 120ips (60 for Monitor A, 60 for Monitor B)
Viewer
1ch, 4ch, 9ch, 13ch, 16ch, Auto & Custum Sequence for Monitor
A
1ch, Auto & Custume Sequce for Monitor B
Max. 60ips in Monitor A or Monitor B
1x, 2x, 4x, 8x, 16x (Forward & Reverse Play)
Step-Forward, Step-Reverse
Playback Performance
Playback Speed
Function
Environment
Operation Temperature
Storage Temperature
Operation Humidity
Storage Humidity
5~45
-10~55
30~80%, free of condensation
93% below, free of condensation
Data Backup/Expansion/Copy
HDD Expandable Data Backup
IEEE1394
Analog VCR
VHS Video output for VCR
Daily / Weekly / Monthly
USB Flash memory disk
Backup Reminder
Data Copy
Input/Output
Video
1 BNC and S-VHS output for Monitor A
1 BNC output for Monitor B
16 Loop through video
Audio
1 I nput : Line-in, 1 Vpp
1 Output : Line-out, 1Vpp
Level : -7~8(16 Step) Recording level
AMP : 20dB amplifier for low level audio
Monitoring : Local and remote
4 Relay outputs (Max DC 30W, AC 62.5VA)
Daily : Day / Night
Digital Output
Digital Output Schedule
Weekly : Weekdays / Weekends
Conditions : MD, Sensor inputs
16 Sensor inputs (Support Dry contact)
Sensor Input
Error! Unknown document property name.
68
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
PTZ Control
Serial Port
RS232(2),RS422/485(2)
Control Method (Local)
Front panel button & IR remote controller
(control IP video channel a s well)
On -the-screen PTZ control on PC
16 points preset per channel
Control Method (Remote)
Preset Mode
Group Mode
1 group per channel
Others
Digital Zoom
2x (Live & PlayBack Mode)
Motion Detection or Sensor input
Alarm triggered Video Data Preservation
Log search
Alarm Trigger
Alarm Data Preservation
Alarm Log
Log monitoring via OSD & Network
Pre : 1~10 seconds
Pre/Post Alarm
Post : 1~60 seconds
Schedule Recording
Daily : Day / Night
Weekly : Weekdays / Weekends
Conditions : Normal / Event
POS/ATM transaction information archived along with
corresponding video data
Text Data Recording
Electricity
Power (Applied Adaptor)
Power Consumption
AC Free Volt
Max. 85W
Typical 50W
Mechanical
Dime nsion (WD H)
Weight
430.0 x 362.0 x 44.0
5.5kg (with one 120GB HDD)
Error! Unknown document property name.
Rugged CCTV
69
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
ELX16-240
APPENDIX
Error! Unknown document property name.
70
Rugged CCTV
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ELX16-240
Error! Unknown document property name.
Rugged CCTV
71
(v 1.0)
Download from Www.Somanuals.com. All Manuals Search And Download.
Rugged CCTV.
5327 Cedar Creek Dr.
Kemp, TX 75143
Tel : (866) 301-2288
Fax : (903) 498-8989
Technical Support: 1-866-301-2288
E-mail: sales@rugged-cctv.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|
KTM Automobile Accessories 50 SX 2007 User Manual
Lanier Copier 5685 User Manual
LST Smoke Alarm SLR E IS User Manual
Lucas Industries Watch LMP079 User Manual
Mace Security Camera CAM 53CIR User Manual
Manhattan Computer Products TV Receiver Plaza HDR S 500GB User Manual
MartinLogan Speaker Ascent LoudSpeaker User Manual
Mattel Doll Y8178 0824 Y8179 User Manual
Maytag Washer W10330943A User Manual
Metra Electronics Automobile Accessories 99 2004 User Manual