INSTALLATION INSTRUCTIONS
FOR
WHEELCHAIR LIFT MODEL NO.
• WL7-vers. C
• WL7-vers. C-1K
DOT-Public Use Lift
PATENTS PENDING
FOR INSIDE VEHICLE
INSTALLATION ONLY
MP-06-09
REV. A
APRIL 2009
© MAXON Lift Corp. 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONALLY LEFT BLANK
PATENTS PENDING
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
INTRODUCTION................................................................................................................... 6
SAFETY SUMMARY............................................................................................................. 6
VEHICLE REQUIREMENTS................................................................................................. 8
LIGHTING.............................................................................................................................. 9
WHEELCHAIR DOOR DIMENSIONS................................................................................. 10
LIFT DIMENSIONS ..............................................................................................................11
LIFT COMPONENTS & TERMINOLOGY............................................................................ 14
DECALS AND DECAL PLACEMENT.................................................................................. 16
DECALS FOR WL7-vers. C................................................................................................. 17
DECALS FOR WL7-vers. C-1K........................................................................................... 18
SERIAL PLATE & CONTROLLER....................................................................................... 19
ANTI-SLIP & SAFETY STRIPING....................................................................................... 20
LIFT INSTALLATION.......................................................................................................... 23
INSTALLATION KITS .......................................................................................................... 23
PREPARING AND POSITIONING THE LIFT ..................................................................... 23
USING TEMPLATE TO POSITION LIFT ............................................................................ 25
MOUNTING THE LIFT ........................................................................................................ 28
INSTALL MAIN CIRCUIT BREAKER................................................................................... 29
ROUTE/CONNECT CABLES & HAND PENDANT ............................................................. 31
CHECKING HYDRAULIC FLUID LEVEL ............................................................................ 39
ADJUSTMENTS.................................................................................................................. 42
MAT SWITCH ADJUSTMENT (IF REQUIRED)................................................................... 42
PLATFORM TILT ADJUSTMENT (MANDATORY) ............................................................. 44
INBOARD SWITCH ADJUSTMENT (IF REQUIRED) ......................................................... 46
CHANGING CONTROLLER TO SPANISH OR ENGLISH (IF REQUIRED) ....................... 48
Download from Www.Somanuals.com. All Manuals Search And Download.
OUTBOARD ROLLSTOP TIME ADJUSTMENT (IF REQUIRED)....................................... 50
FLOOR POSITION ADJUSTMENT (MANDATORY) .......................................................... 52
SYSTEM DIAGRAMS ......................................................................................................... 57
HYDRAULIC SYSTEM DIAGRAM ...................................................................................... 57
ELECTRICAL SYSTEM DIAGRAM..................................................................................... 58
COMPLETED LIFT INSTALLATION CHECKLIST............................................................. 59
PATENTS PENDING
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
This manual contains instructions for installing the MAXON MOBILITY Wheelchair Lift in a
transit vehicle. Please follow these instructions carefully and call us immediately if you need
assistance with the installation. Do not take shortcuts, skip over installation steps, or modify
the Lift. Correct installation is important to ensure the Lift operates correctly. If you have
questions that are not covered in this manual, please contact:
MAXON Lift Corp. - Customer Service
11921 Slauson Ave., Santa Fe Springs, CA 90670
Phone: (800) 227-4116 FAX: (888) 771-7713
E-mail: cservice@maxonlift.com
After receiving the Wheelchair Lift, unpack the Lift and check it for freight damage. For
freight-damaged items, immediately submit a claim to the carrier.
Make sure installation kit contains all items on the packing list shipped with the kit. Please
report any missing items immediately to our Customer Service Department. The Warranty
Registration Card, shipped with the Lift, must be completed and returned to Maxon Lift
Corp. within 30 days after installation and/or receipt of the Lift.
SAFETY SUMMARY
Comply with the following WARNINGS and safety precautions while maintaining the
Wheelchair Lift. See Operator’s Manual for operating safety requirements.
WARNING
!
1. Read and understand the instructions in this Installation Manual before installing Lift.
2. Before operating the Lift, read and understand the operating instructions contained in
the Operator’s Manual.
3. Comply with all WARNING and instruction decals attached to both the Lift and the ve-
hicle.
4. Keep decals clean and legible. If decals are illegible or missing, free replacement
decals are available from MAXON Lift Corp. Customer Service. Refer to DECALS &
DECAL PLACEMENT and the instructions for installing decals on vehicle in this manu-
al.
5. Consider the safety and location of bystanders and location of nearby objects when op-
erating the Lift. Stand to one side of platform while operating the Lift.
6. Do not allow untrained persons to operate the Lift.
7. Do not stand, or allow obstructions, under the Platform when lowering the Lift. Be sure
your feet are clear of the Lift.
8. Keep fingers, hands, arms, legs, and feet clear of moving Lift parts (and platform
edges) when operating the Lift.
9. Make sure vehicle battery power is disconnected when installing Lift. Connect
vehicle power to the Lift only when instructed to connect power.
PATENTS PENDING
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Read and understand the instructions in this Installation Manual before installing Lift.
2. Before operating the Lift, read and understand the operating instructions contained in the
Operator’s Manual.
3. Comply with all WARNING and instruction decals attached to both the Lift and the ve-
hicle.
4. Keep decals clean and legible. If decals are illegible or missing, free replacement de-
cals are available from MAXON Lift Corp. Customer Service. Refer to DECALS & DE-
CAL PLACEMENT and the instructions for installing decals on vehicle in this manual.
5. Consider the safety and location of bystanders and location of nearby objects when op-
erating the Lift. Stand to one side of platform while operating the Lift.
6. Do not allow untrained persons to operate the Lift.
PATENTS PENDING
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE REQUIREMENTS
The minimum vehicle requirements
for installing the WL7 Wheelchair Lift
are described below. Installing the
Lift in accordance with the vehicle
requirements and the instructions in
this manual will result in an installation
that is compliant with Federal Motor
Vehicle Safety Standard (FMVSS) 403
and FMVSS 404.
M
F
BODY STRENGTH
WARNING
!
FORCE & MOMENT PRODUCED
BY LIFT ON VEHICLE FLOOR
FIG. 8-1
Consult body manufacturer for body
strength data. Make sure the forces
created by the Lift are within the limits
prescribed by body manufacturer.
MODEL
“F” (LB) “M” (LB-IN)
NOTE: The Lift represents approximately
400 lbs. of “F” shown in the illus-
tration.
WL7-vers. C
2800
154,000
187,000
WL7-vers. C-1K 3400
TABLE 8-1
The WL7 Lift must be bolted to the vehicle
body. Body must withstand the maximum
vertical force (“F”) and moment of force (“M”)
(FIG. 8-1 and TABLE 8-1 ) produced
by the Lift on the vehicle floor surface shown
in FIGS. 8-2 and 8-3.
42.5”
15”
LIFT FOOTPRINT ON VEHICLE FLOOR
(LIFT WITH 33” OR 34” PLATFORM)
FIG. 8-2
39.5”
15”
LIFT FOOTPRINT ON VEHICLE
FLOOR (LIFT WITH 30” PLATFORM)
FIG. 8-3
PATENTS PENDING
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL POWER
Vehicle must have a 12 volt dc electrical
system capable of supplying 65 amperes
of electrical power to the Lift for each
operating cycle.
SAFETY INTERLOCK SYSTEM
Vehicle must have an FMVSS 403 compliant, onboard
Safety Interlock System that interfaces with the Wheel-
chair Lift interlock signal. Interlock signal may be V+ or
V-. The interlock system on a host vehicle must:
Prevent the Lift from deploying when vehicle is in
drive or reverse.
Prevent the vehicle from moving when the Lift is
deployed.
Prevent the Lift from disabling vehicle if the Lift
signals a deployed condition when the vehicle is
moving.
•
•
•
For the applicable interlock electrical connections on the Lift,
refer to the ELECTRICAL SYSTEM DIAGRAM in this manu-
al. For more information about the interlock connections, call:
MAXON Lift Corp. Technical Service at (800) 227-4116
LIGHTING
Public use vehicle manufacturers are responsible for
complying with Lift lighting requirements stated in Fed-
eral Motor Vehicle Safety Standard No. 404, Platform
Lift Installations in Motor Vehicles (49 CFR 571.404).
PATENTS PENDING
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE REQUIREMENTS - Continued
WHEELCHAIR DOOR DIMENSIONS
A
B
WHEELCHAIR DOOR DIMENSIONS ON
TYPICAL VEHICLE WITH SIDE DOOR
(SEE TABLE 10-1)
FIG. 10-1
A
B
WHEELCHAIR WHEELCHAIR
DOOR WIDTH DOOR HEIGHT
MODEL
DESCRIPTIONS
(MINIMUM)
(MINIMUM)
30” WIDE PLATFORM
RH PUMP
39”
30” WIDE PLATFORM
LH PUMP
33” WIDE PLATFORM
RH PUMP
42”
43”
56”
33” WIDE PLATFORM
LH PUMP
34” WIDE PLATFORM
RH PUMP
34” WIDE PLATFORM
LH PUMP
TABLE 10-1
PATENTS PENDING
10
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFT DIMENSIONS
C
18.9”
D
13.3”
2.9”
55.13”
1.4”
0.5”
39”
25”
E
4.75”
18-3/4”
F
FRONT VIEW OF STOWED LIFT
(LH PUMP MODEL SHOWN)
(SEE TABLE 11-1)
SIDE VIEW OF STOWED LIFT
(LH PUMP MODEL SHOWN)
FIG. 11-1
FIG. 11-2
C
D
E
F
OVERALL LIFT
WIDTH (INCLUDING
PUMP COVER)
MODEL
DESCRIPTIONS
LIFT WIDTH AT
WARNING BEACONS
LIFT WIDTH AT
HANDRAILS
LIFT WIDTH AT
BASE PLATE
30” WIDE PLATFORM
RH PUMP
40.25”
43.25”
44.25”
38”
41”
42”
39.5”
42.5”
43.5”
45.5”
48.5”
49.5”
30” WIDE PLATFORM
LH PUMP
33” WIDE PLATFORM
RH PUMP
33” WIDE PLATFORM
LH PUMP
34” WIDE PLATFORM
RH PUMP
34” WIDE PLATFORM
LH PUMP
TABLE 11-1
11
PATENTS PENDING
Download from Www.Somanuals.com. All Manuals Search And Download.
VEHICLE REQUIREMENTS - Continued
WHEELCHAIR
DOOR
0.75”
(MIN.)
18-3/4”
(APPROX.)
48”(MAX.)
WHEELCHAIR DOOR CLEARANCE & FLOOR
HEIGHT ON TYPICAL VEHICLE WITH SIDE DOOR
FIG. 12-1
PATENTS PENDING
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3.75”
(48” FLOOR LEVEL - REF)
6.75”
(46” FLOOR LEVEL - REF)
8.75”
(44” FLOOR LEVEL - REF)
10.25”
(42” FLOOR LEVEL - REF)
BASE PLATE
OUTBOARD
EDGE (REF)
TYPICAL
VEHICLE REAR
BUMPER
(VAN GND LVL)
(BUS GND LVL)
(BUS GND LVL)
BODY CLEARANCE POINTS: 32”, 40”, 42”, 46” & 48” FLOOR HEIGHTS
FIG. 13-1
PATENTS PENDING
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFT COMPONENTS & TERMINOLOGY
6
10
INBOARD
10
RIGHT
4
11
6
7
8
12
5
2
9
1
LEFT
3
12
OUTBOARD
LIFT COMPONENTS (SEE TABLE 13-1)
FIG. 14-1
PATENTS PENDING
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM
NAME
DESCRIPTION
1. THRESHOLD PLATE
Component that bridges the entry way, through the
Lift, into the vehicle. Detects if that portion of Lift is
occupied during “UP/DOWN” operation between
vehicle floor and the ground.
2. OUTBOARD ROLLSTOP Barrier to prevent the wheelchair from rolling off of
the platform. Provides entry/exit ramp for platform
on the ground.
3. PLATFORM
Contains the wheelchair and occupant during “UP/
DOWN” operation between vehicle floor and the
ground.
4. HANDRAILS
(Left/Right) Provides a hand hold for the Lift
occupant.
5. INBOARD ROLLSTOP
Barrier to prevent the wheelchair from rolling off
inboard side of platform. Provides bridge between
platform and threshold.
6. HYDRAULIC CYLINDER (Left/Right) Telescoping steel tube and rod,
pressurized by hydraulic fluid, that folds and unfolds
the Lift and moves the Lift up and down.
7. HYDRAULIC POWER
UNIT (COVER IS
SHOWN)
Contains motorized hydraulic pump, manually
operated backup pump, fluid lines, and controls that
operate the hydraulic cylinders.
8. LIFT CONTROLLER
(BRAIN BOX)
Electronic device that controls and monitors Lift
operation and the interlock connection with the
vehicle.
9. BASE
Structure that secures Lift to the vehicle floor.
10. THRESHOLD WARNING Flashing red light indicates threshold is occupied by
BEACON
a person or object when the platform is below floor
level. Indicates outboard rollstop is open if platform
is at floor level.
11. THRESHOLD WARNING Audible alarm sounds when threshold is occupied
ALARM
by a person or object when the platform is below
floor level. Also indicates outboard rollstop is open
if platform is at floor level.
12. PLATFORM LIGHTS
Illuminates the platform when ready to load at floor
level and during “UP/DOWN” operation between
vehicle floor and the ground.
TABLE 15-1
PATENTS PENDING
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DECALS AND DECAL PLACEMENT
DECAL ”D”
DECAL “O”
DECAL “K”
DECAL “A”
DECAL “B”
DECAL “F”
DECAL “L”
DECAL “M”
DECAL “I”
DECAL“J”
DECAL“N”
DECAL “C”
DECAL
“E”
DECAL“N”
DECAL “H”
FIG. 16-1
All WARNING, CAUTION, and OPERATION de-
cals provided with Wheelchair Lift must always be
in place on the Lift and vehicle (see FIG. 36-1), and
must always be legible. If decals are missing or il-
legible, get free replacement decals from:
MAXON Lift Corp. - Customer Service
11921 Slauson Ave., Santa Fe Springs, CA 90670
Phone: (800) 227-4116 FAX: (888) 771-7713
E-mail: cservice@maxonlift.com
PATENTS PENDING
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DECALS FOR WL7-vers. C
DECAL SET P/N 268302-01
FIG. 17-1
PATENTS PENDING
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DECALS AND DECAL PLACEMENT - Continued
DECALS FOR WL7-vers. C-1K
DECAL SET P/N 268302-03
FIG. 18-1
PATENTS PENDING
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIAL PLATE & CONTROLLER
CONTROLLER OVERLAY
P/N 2667630-01
FIG. 19-1
SERIAL PLATE
P/N 905246-8
FIG. 19-2
PATENTS PENDING
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTI-SLIP & SAFETY STRIPING
(30” WIDE PLATFORM)
YELLOW TAPE
(BOTTOM-ROLLSTOP)
P/N 905293-17
ANTI-SLIP TAPE
(ROLLSTOP)
P/N 096020-13
ANTI-SLIP TAPE
P/N 096024-10
ANTI-SLIP TAPE
P/N 096020-10
ANTI-SLIP TAPE
P/N 096013-10
YELLOW TAPE
(OUTBOARD)
P/N 905293-11
YELLOW TAPE
(OUTBOARD)
P/N 905293-14
YELLOW TAPE
(INBOARD)
P/N 905293-16
ANTI-SLIP TAPE
(ROLLSTOP)
P/N 096020-13
YELLOW TAPE
P/N 905293-11
YELLOW TAPE
P/N 905293-14
YELLOW TAPE
(INBOARD & OUTBOARD)
P/N 905293-13
FIG. 20-1
PATENTS PENDING
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTI-SLIP & SAFETY STRIPING - Continued
(33” WIDE PLATFORM)
YELLOW TAPE
(BOTTOM-ROLLSTOP)
P/N 905293-18
ANTI-SLIP TAPE
(ROLLSTOP)
P/N 096020-14
ANTI-SLIP TAPE
P/N 096024-11
ANTI-SLIP TAPE
P/N 096020-11
ANTI-SLIP TAPE
P/N 096013-11
YELLOW TAPE
(OUTBOARD)
P/N 905293-11
YELLOW TAPE
(OUTBOARD)
P/N 905293-14
YELLOW TAPE
(INBOARD)
P/N 905293-16
ANTI-SLIP TAPE
(ROLLSTOP)
P/N 096020-14
YELLOW TAPE
P/N 905293-11
YELLOW TAPE
P/N 905293-14
YELLOW TAPE
(INBOARD & OUTBOARD)
P/N 905293-15
FIG. 21-1
PATENTS PENDING
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTI-SLIP & SAFETY STRIPING - Continued
(34” WIDE PLATFORM)
YELLOW TAPE
(BOTTOM-ROLLSTOP)
P/N 905293-18
ANTI-SLIP TAPE
(ROLLSTOP)
P/N 096020-15
ANTI-SLIP TAPE
P/N 096024-12
ANTI-SLIP TAPE
P/N 096020-12
ANTI-SLIP TAPE
P/N 096013-11
YELLOW TAPE
(OUTBOARD)
P/N 905293-11
YELLOW TAPE
(OUTBOARD)
P/N 905293-14
YELLOW TAPE
(INBOARD)
P/N 905293-16
ANTI-SLIP TAPE
(ROLLSTOP)
P/N 096020-15
YELLOW TAPE
P/N 905293-11
YELLOW TAPE
P/N 905293-14
YELLOW TAPE
(INBOARD & OUTBOARD)
P/N 905293-15
FIG. 22-1
PATENTS PENDING
22
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFT INSTALLATION
INSTALLATION KITS
An installation kit is required to install Lift on your vehicle. Refer to the instruction sheet,
included with the installation kit, for specific instructions to fit the Lift to your vehicle.
PREPARING AND POSITIONING THE LIFT
1. Make sure you have the correct model of Lift.
NOTE: Keep shipping straps on Lift until Lift is
bolted to vehicle and power is connected.
WHEELCHAIR
DOORWAY
2. Unpack the Lift and check for damage. Report
DOOR
damage to:
MAXON Lift Corp. - Customer Service
11921 Slauson Ave., Santa Fe Springs, CA 90670
Phone: (800) 227-4116 FAX: (888) 771-7713
E-mail: cservice@maxonlift.com
3. Open the wheelchair door on vehicle (FIG. 23-1) in
which Lift will be mounted. Secure door wide open.
VEHICLE RH SIDE VIEW
FIG. 23-1
4. Check the clearance dimensions of your vehicle
before beginning installation. Refer to VEHICLE
REQUIREMENTS section in this Installation Manual.
PATENTS PENDING
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARING AND POSITIONING THE LIFT - Continued
NOTE: You may use a template instead of the
Lift for positioning the Lift on vehicle. To
use a template, refer to USING TEM
PLATE TO POSITION LIFT section in
this Installation Manual.
WHEELCHAIR
LIFT
DOOR
5. Using an appropriate lifting device that
can safely lift 500 pounds, raise Lift to the
wheelchair doorway. Place the Lift inside
doorway (FIG. 24-1). Align outboard
edge of Lift threshold plate parallel with
outboard edge of doorway. The decal on
the underside of the Lift platform must
face outboard (FIG. 24-1).
DECAL (FACES
OUTBOARD)
6. Position the Lift according to the clearance di-
mensions given in VEHICLE REQUIREMENTS
section in this Installation Manual.
VEHICLE RH SIDE VIEW
FIG. 24-1
7. Remove lifting device and close wheelchair door.
Enter the vehicle. Verify the wheelchair door
closes correctly and the minimum clearance is
3/4”. If door will not close correctly, reposition the
Lift.
8. Secure vehicle door wide open (FIG. 24-1).
9. Check under the vehicle floor for possible in-
terference between the Lift base plate mount-
ing bolts and the vehicle underbody. For
example, check subframe members, wiring
harnesses, cables, and fluid lines.
PATENTS PENDING
24
Download from Www.Somanuals.com. All Manuals Search And Download.
USING TEMPLATE TO POSITION LIFT
1. Fabricate template for base plate hole pattern
according to the dimensions shown in FIGS.
25-1, 25-2, 26-1 and 26-2. Use a suitable
material that maintains correct shape and
dimensions.
BASE PLATE HOLE PATTERN FOR LIFTS
WITH 33” & 34” WIDE PLATFORMS & RH PUMP
FIG. 25-1
BASE PLATE HOLE PATTERN FOR LIFTS
WITH 33” & 34” WIDE PLATFORMS & LH PUMP
FIG. 25-2
PATENTS PENDING
25
Download from Www.Somanuals.com. All Manuals Search And Download.
USING TEMPLATE TO POSITION LIFT - Continued
BASE PLATE HOLE PATTERN FOR LIFTS
WITH 30” WIDE PLATFORM & LH PUMP
FIG. 26-1
BASE PLATE HOLE PATTERN FOR LIFTS
WITH 30” WIDE PLATFORM & RH PUMP
FIG. 26-2
PATENTS PENDING
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
For vehicles with 48” floor height:
If the front edge of Lift base plate is moved more than 3.75” (5” from outside of
body, as shown in FIG. 11-1) away from the inside of the wheelchair door, lower
Lift arms can hit vehicle body before platform reaches the ground. See the
vehicle floor levels plotted in FIG. 11-1 and maintain the clearance for the floor
level that applies to your Lift installation.
2. Center the template inside wheelchair door-
way (FIG. 27-1). Line up the outboard
edge of template parallel with inboard edge
of doorway. Maintain center and the clear-
ance dimension shown.
VEHICLE BODY
(CUTAWAY)
BASE PLATE TEMPLATE
HOLE PATTERN
BACK
1
2
3
7
9
4
IN
D
10
6
5
8
3.75”
FRONT
CENTER
BASE PLATE TEMPLATE CLEARANCE FROM WHEEL-
CHAIR DOOR (TOP VIEW, SIDE DOOR SHOWN)
FIG. 27-1
PATENTS PENDING
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING THE LIFT
NOTE: MAXON recommends using all 10 carriage screws (Kit items) to bolt Lift to
vehicle. A minimum of 8 screws or bolts and use of holes 1, 2, 3, 4 & 9 are
required for correct installation. Also, the 3 front holes should be selected to
give a symmetrical bolt pattern (i.e. holes 5,10, & 8 or holes 6,10, & 7).
BACK
1. Use template (FIG. 27-1) or the base plate on the
4
9
3
1
2
Lift (FIG. 28-1, holes 1-10) to mark eight (8) to
ten (10) 7/16” mounting holes through the vehicle
floor. Before drilling holes in the vehicle floor, make
sure no wires and fluid lines are too close to hole
locations. Drill holes 1, 2, 9, 3, and 4.
8
5
6
10
FRONT
7
BASE PLATE BOLT
HOLE PATTERN
FIG. 28-1
NOTE: Vehicle floor must meet the requirements shown at the beginning of the
VEHICLE REQUIREMENTS section in this Installation Manual.
2. Position Lift so holes 1-10 in the base plate (FIG. 28-1)
are aligned with the correct holes drilled in vehicle floor.
3. Temporarily secure Lift to vehicle with two mounting
bolts (Kit items), inserted through base plate holes 1
and 4, or holes 2 and 3 (FIG. 28-1). Use two lock
nuts and correct under-vehicle supports (Kit items) to
secure the Lift. Use instructions supplied with vehicle
installation kit to select the correct bolts, nuts and sup-
ports. Alternately, tighten the two bolts and nuts to 20
to 30 LBS.-FT.
PATENTS PENDING
28
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL MAIN CIRCUIT BREAKER
WARNING
!
To prevent personal injury and equipment damage, make sure power is discon-
nected from Lift when installing electrical parts.
NOTE: Apply dielectric grease on all electrical connections after all electrical cables are
connected.
1. Attach 90 amp main circuit breaker (Kit item) to
vehicle so power cable (Kit item) is within reach
of the battery, as follows. Find a place to attach
bracket (FIG. 29-1). (Note: The power cable must
be able to reach between 90 amp circuit breaker
and (+) battery terminal without straining the con-
nections.) Attach 90 amp circuit breaker to brack-
et. Next, attach bracket to vehicle with four (4) #12
1/4” FLAT
WASHER
self-drilling screws (Kit items).
(2 PLACES)
BATTERY
1/4”-20
LOCK NUT
(2 PLACES)
2 AWG POWER
CABLE (SHORT CABLE)
POWER UNIT
(REF)
90 AMP MAIN
CIRCUIT BREAKER
1/4”-20
CAP SCREW
(2 PLACES)
#12 SELF-DRILLING
SCREW (4 PLACES)
2 AWG POWER CABLE
(LONG CABLE CONNECTED
BETWEEN TERMINAL OF
STARTER SOLENOID AND MAIN
CIRCUIT BREAKER)
MAIN CIRCUIT BREAKER & CABLING
FIG. 29-1
PATENTS PENDING
29
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL MAIN CIRCUIT BREAKER - Continued
2. Connect one end of power cable to 90
amp main circuit breaker (FIG. 30-1).
Do not connect battery end until instructed
to connect the battery.
1/4” FLAT
WASHER
(2 PLACES)
BATTERY
1/4”-20
LOCK NUT
(2 PLACES)
2 AWG POWER
CABLE (SHORT CABLE)
POWER UNIT
(REF)
90 AMP MAIN
CIRCUIT BREAKER
1/4”-20
CAP SCREW
(2 PLACES)
#12 SELF-DRILLING
SCREW (4 PLACES)
2 AWG POWER CABLE
(LONG CABLE CONNECTED
BETWEEN TERMINAL OF
STARTER SOLENOID AND MAIN
CIRCUIT BREAKER)
MAIN CIRCUIT BREAKER & CABLING
FIG. 30-1
3. Lastly, connect one end of long power
cable to 90 amp main circuit breaker
(FIG. 30-1).
PATENTS PENDING
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTE/CONNECT CABLES & HAND PENDANT
! CAUTION
Never route an energized wire. Make sure the battery is disconnected. Always
route electrical wire clear of any moving parts, brake lines, sharp edges, and ex-
haust systems. Never route power cable next to a wiring harness on the vehicle.
Do not loop excess cable. Cut the cable to fit and leave slack. Attach securely.
If drilling is necessary, be sure to check underside of vehicle before drilling so
you do not damage any fuel lines, vent lines, brake lines or wires. When routing
electrical wire through a hole in vehicle floor, use supplied grommet to protect
wires from chafing.
1. Locate and drill a 1-5/16” hole through
the vehicle floor (FIG. 31-1). Drill the
hole in a location that will be hidden
by the pump cover and that will allow
power cable to be routed to power input
bracket (FIG. 31-1). Since the inter-
lock system wiring from the Lift also
branches out in that area, locate the
hole so the 3-conductor Interlock system
cable can be routed from the Lift through
the vehicle floor to the vehicle safety in-
terlock. Install the plastic grommet (FIG.
31-1) on the vehicle floor with 2 of the
#12 self-drilling screws.
POWER
INPUT
BRACKET
LONG
POWER
CABLE
SELF-TAPPING
SCREWS
GROMMET
2. Route the long power cable (Kit item)
from main circuit breaker (FIG. 31-2),
underneath vehicle floor to power input
bracket (FIG. 31-1).
FIG. 31-1
LONG POWER
CABLE
3. Secure power cable every 8”-10”.
90 AMP MAIN
CIRCUIT BREAKER
FIG. 31-2
PATENTS PENDING
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTE/CONNECT CABLES & HAND PENDANT - Continued
POWER
INPUT
BRACKET
4. Cut any excess wire from long power cable.
Strip 1/2” insulation from the cut end and
install 2 GA terminal lug and shrink tubing.
2 GA
TERMINAL
LUG
Next, insert the power cable through the
protective cover (FIG. 32-1). Connect the
cable terminal to the terminal stud on the
power input bracket as shown in FIG. 32-
1. Position the protective cover over the
power cable connection (FIG. 32-1).
TERMINAL
STUD
EXTERNAL
TOOTH LOCK
WASHER
HEX
NUT
LONG
POWER
CABLE
PROTECTIVE
COVER
FIG. 32-1
5. Route the interlock cable from safety interlock
system on the vehicle, underneath vehicle floor
and through the grommet, and up to the Lift (FIG.
32-2). If possible, use the same cable routing as
the long power cable installed in previ-
ous steps. Secure the interlock cable
every 8”-10”.
INTERLOCK
CABLE
6. Make sure interlock cable will reach
the white-red stripe wire (interlock
signal from vehicle) and the brown
wire (interlock signal to vehicle) on
the Lift (FIG. 32-2). Signal may
be ground or V+. Connect the inter-
lock wires from the vehicle interlock
system to the white-red stripe wire
and brown wire on the Lift (FIG.
32-2).
INTERLOCK WIRE
(SIGNAL FROM
VEHICLE)
INTERLOCK WIRE
(SIGNAL TO
VEHICLE)
WHITE-RED STRIPE
WIRE (FROM LIFT)
BROWN WIRE
(FROM LIFT)
FIG. 32-2
PATENTS PENDING
32
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Uncoil the ground cable from the bottom of
the pump cover. Route the ground cable
on the Lift through grommet in vehicle floor
(FIG. 33-1A & 33-1B).
GROUND
CABLE
GROMMET
GROUND CABLE ROUTED FROM LIFT
FIG. 33-1A
NOTE: Clean the ground cable
connection point on the
frame down to bare metal.
NOTE: If there is a grounding
point on the frame, use it
to connect ground cable.
BARE
METAL
TERMINAL LUG
3/8”-16 X 1” LG.
Skip step 8.
CAP SCREW
VEHICLE
NOTE: Apply dielectric grease to
FRAME
all electrical connections.
8. Extend the ground cable to reach
vehicle frame (FIG. 33-2). Con-
nect to an existing grounding point
if available. If necessary, drill a
13/32” (0.406”) hole in vehicle
frame for bolting the ground cable
terminal lug (FIG. 33-2).
3/8”-16
HEX NUT
GROUND
CABLE
9. Bolt the ground cable terminal lug
to vehicle frame as shown in FIG.
33-2.
3/8” LOCK
WASHER
BOLTING GROUND CABLE
TO VEHICLE FRAME
FIG. 33-2
PATENTS PENDING
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTE/CONNECT CABLES & HAND PENDANT - Continued
CAUTION
!
To prevent vehicle access door from pinching and damaging the hand pendant
cable, secure cable away from the door frame. Also, be sure that the hand
pendant cable does not interfere with or bind against moving parts.
10. Connect the hand pendant cable as follows.
Feed the cable through the hole located
in the main frame (FIG. 34-1). Secure cable
strain relief to main frame with plastic nut (FIG.
34-1). Next, connect hand pendant connector
to wiring harness (FIG. 34-1).
WIRING
HARNESS
CONNECTOR
MAIN
FRAME
HEX NUT
CONNECTOR
HAND
STRAIN
RELIEF
PENDANT
CONNECTING HAND PENDANT CABLE
(RH SIDE CONNECTION SHOWN)
FIG. 34-1
PATENTS PENDING
34
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Find accessible place on vehicle wall or
wheelchair door (near Lift) to place the
hand pendant hanger and cable hook (FIG.
35-1).
HAND PENDANT
& HANGER
CABLE HOOK
PUMP COVER
TYPICAL LOCATION (INSIDE VEHICLE)
FOR STOWING HAND PENDANT
FIG. 35-1
PATENTS PENDING
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTE/CONNECT CABLES & HAND PENDANT - Continued
12. Place decals (from Parts Box) on the vehicle, near the hand pendant (typical place-
ment shown in FIG. 36-1). Make sure decals are visible to operator when Lift is
being operated.
HAND PENDANT &
HANGER MOUNTING
DECAL “J”
DECAL “I”
DECAL “A”
DECAL “C”
DOOR
DECAL “B”
CABLE
HOOK
DECAL “A”
P/N 268303-01
DECALS AND HAND PENDANT
MOUNTING ON VEHICLE
FIG. 36-1
DECAL SET FOR WL7-vers.C-1K
P/N 267620-04
DECAL SET FOR WL7-vers.C
P/N 267620-02
FIG. 36-3
FIG. 36-2
PATENTS PENDING
36
Download from Www.Somanuals.com. All Manuals Search And Download.
POSITIVE (+) BATTERY
TERMINAL
SHORT POWER
CABLE
13. Connect short power cable to vehicle
battery as follows. Remove nut from
positive (+) battery terminal connec-
tor (FIG. 37-1). Connect the power
cable. Reinstall nut.
BOLT
NUT
CONNECTING POWER TO LIFT (TYPICAL)
FIG. 37-1
POWER ON/OFF
SWITCH
14. Turn ON power ON/OFF switch on
pump cover to power the Lift (FIG.
37-2). The POWER light on hand
pendant should be illuminated (FIG.
37-3). Briefly press the FOLD button
on hand pendant (FIG. 37-3) to pres-
surize hydraulic system. Then, remove
remaining shipping straps.
STOWED LIFT - LH SIDE SHOWN
FIG. 37-2
UP
FOLD
FOLD
UNFOLD
POWER
LIGHT
HAND PENDANT
FIG. 37-3
PATENTS PENDING
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ROUTE/CONNECT CABLES & HAND PENDANT - Continued
15. Press the UNFOLD button on hand
pendant to unfold Lift (FIG. 38-
1). Platform lights will turn on when
platform is at floor level.
PLATFORM LIGHT
(2 PLACES)
LIFT AT FLOOR LEVEL
FIG. 38-1
16. Next, press DOWN button on hand
pendant. When the platform reaches
the ground, the outboard rollstop will
automatically open to ramp position
OUTBOARD
ROLLSTOP
(FIG. 38-2).
PLATFORM
GROUND
PLATFORM LOWERED TO
GROUND LEVEL
FIG. 38-2
17. Install the remaining bolts, lock nuts, and
under-vehicle supports supplied with
your installation kit. Use the instruction
sheet (Kit item) for information to install
the remaining Kit items correctly.
NOTE: Lift installation is not complete until all the instructions in this manual,
your installation kit instructions, and the checks and adjustments that
follow (in this manual) are completed.
PATENTS PENDING
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING HYDRAULIC FLUID LEVEL
CAUTION
!
Keep dirt, water and other contaminants from entering the hydraulic sys-
tem. Before opening the hydraulic fluid reservoir filler cap, drain plug and
hydraulic lines, wipe off contaminants that can get in the openings. Also,
protect the openings from accidental contamination.
1. Check the hydraulic fluid level in reservoir as
follows. With Lift in STOWED position, fluid
level should be as shown in FIG. 39-1.
PUMP
COVER
INSPECTION
SLOT
RESERVOIR
2”
HYDRAULIC FLUID LEVEL
(LH PUMP SHOWN)
FIG. 39-1
2. If needed, add fluid to the reservoir
as follows. Unbolt the pump cover as
shown in FIG. 39-2.
PUMP COVER
SCREWS
UNBOLTING/BOLTING PUMP COVER
(LH PUMP SHOWN)
FIG. 39-2
PATENTS PENDING
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING HYDRAULIC FLUID LEVEL - Continued
3. Pull out filler cap (FIG. 40-1). Fill the
reservoir with hydraulic fluid (TABLE
40-1) to level shown in FIG. 40-1.
Reinstall filler cap (FIG. 40-1).
RECOMMENDED HYDRAULIC FLUID
FILLER
BRAND
ROSEMEAD
EXXON
PART NUMBER
THS FLUID 17111
UNIVIS HVI 26
CAP
RESERVOIR
TABLE 40-1
2”
NOTE: If the expected seasonal
temperatures are below
20°F, use MIL-H-5606G
hydraulic fluid.
HYDRAULIC FLUID LEVEL
(LH PUMP SHOWN)
FIG. 40-1
4. Bolt on the pump cover as shown
in FIG. 39-2. Tighten the 5/16”-18
cover screws until snug.
PATENTS PENDING
40
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONALLY LEFT BLANK
PATENTS PENDING
41
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
MAT SWITCH ADJUSTMENT (IF REQUIRED)
1. Make sure power switch
POWER SWITCH
(FIG. 42-1A) is turned
on. Lower Lift to the
ground (FIG. 42-
1A).
5/8”
HEIGHT MEASUREMENT
(RH SIDE SHOWN)
FIG. 42-1B
LIFT AT GROUND LEVEL
FIG. 42-1A
2. Measure the height of the
threshold plate as shown in FIG.
42-1B. If the height is 5/8”,
go to step 4 (skip step 3). If the
height is not 5/8”, go to step 3.
LIFT THRESHOLD
FIG. 42-2A
3. Set edge of the threshold plate to
5/8” height by turning the adjust-
ment screw on the RH side of
threshold plate (FIG. 42-2B).
Turn adjustment screw counter-
clockwise (FIG. 42-3) to raise
threshold plate or clockwise to
lower. Repeat for LH side of
threshold plate. Alternately mea-
sure height (see instruction 2).
Then, turn the adjustment screw
on RH side and LH side until the
entire edge of threshold plate is at
5/8” height.
ADJUSTMENT
SCREW
HEIGHT ADJUSTMENT SCREW
(RH SIDE SHOWN)
FIG. 42-2B
CCW - RAISE
CW - LOWER
HEIGHT ADJUSTMENT SCREWS
FIG. 42-3
PATENTS PENDING
42
Download from Www.Somanuals.com. All Manuals Search And Download.
THRESHOLD
WARNING BEACON
4. Turn the MAT switch adjustment screw
(FIGS. 43-1B and 43-2) clockwise until
threshold warning alarm and beacons acti-
vate (FIG. 43-1A). Then, turn adjustment
screw counter-clockwise (FIG. 43-2) ap-
proximately 1-1/2 turn. Warning alarm and
beacons should turn off.
THRESHOLD
WARNING ALARM
BASE
PLATE
ADJUSTMENT
SCREW
THRESHOLD
PLATE
ADJUSTING SWITCH
FIG. 43-1B
LH SIDE OF LIFT
FIG. 43-1A
CW - UNTIL ALARM &
BEACONS TURN ON
1-1/2 TURN CCW - ALARM
& BEACONS TURN OFF
MAT SWITCH ADJUSTMENT SCREWS
FIG. 43-2
5. Step on threshold plate. Warning alarm
and beacons should activate. If the warning
alarm and beacons do not activate, slightly
turn adjustment screw (FIGS. 43-1B and
43-2) clockwise. Repeat until warning
alarm and beacons activate when stepping
on threshold plate and deactivate stepping
off threshold plate.
PATENTS PENDING
43
Download from Www.Somanuals.com. All Manuals Search And Download.
PLATFORM TILT ADJUSTMENT (MANDATORY)
NOTE: The platform tilt adjustment is important for operation of the outboard roll-
stop and for keeping platform level when it reaches the ground. Vehicle
floor height, Lift and stiffness of the vehicle suspension may change the
angle of platform on the ground.
1. Make sure power switch
(FIG. 44-1) is turned
on. Lower the platform
and stop approximately 4”
above ground.
POWER
SWITCH
GROUND
LEVEL
PLATFORM
4”
PLATFORM LOWERED TO GROUND LEVEL
FIG. 44-1
POWER
SWITCH
2. Measure distance from
front of the platform (1) to
the ground (FIG. 44-2).
Next, measure the distance
from the bottom of the vertical
arm (2) to the ground
VERTICAL
ARM
GROUND
LEVEL
(FIG. 44-2).
PLATFORM
(1)
(2)
3. The measurement at the vertical
arm (2) must be 1/2” -1” more than
the measurement at the front of
platform (1). For example: If you
measure 4” at the front (1), then you
should measure from 4-1/2” to 5” at
the vertical arm (2). If there is not a
1/2” - 1” difference, go to step 4 to
obtain the correct measurement.
PLATFORM LOWERED TO GROUND LEVEL
FIG. 44-2
PATENTS PENDING
44
Download from Www.Somanuals.com. All Manuals Search And Download.
OUTBOARD ROLLSTOP
(REF)
4. Manually lower the inboard
rollstop for access to the ad-
justment screws (FIG. 45-1).
To ensure proper leveling, turn
platform tilt adjustment screws
(FIG. 45-1) an equal amount
on both sides of platform. Turn
adjustment screws clockwise
(FIG. 45-2) to tilt the platform
up or counter-clockwise to tilt
platform down.
ADJUSTMENT
SCREW
INBOARD ROLLSTOP
PLATFORM
PLATFORM TILT ADJUSTMENT SCREW
(BACK VIEW OF PLATFORM SHOWN)
FIG. 45-1
CW - PLATFORM
TILT UP
CCW - PLATFORM
TILT DOWN
PLATFORM TILT ADJUSTMENT SCREWS
FIG. 45-2
PATENTS PENDING
45
Download from Www.Somanuals.com. All Manuals Search And Download.
INBOARD SWITCH ADJUSTMENT (IF REQUIRED)
NOTE: Do this procedure if the Controller reads “IBRS SW” when Inboard Rollstop is
locked in the up position.
The adjustment is done correctly if the Controller does not read “IBRS SW”
when the Inboard Rollstop is locked in the up position.
POWER
SWITCH
1. Position the platform at floor level
(FIG. 46-1).
PLATFORM AT FLOOR LEVEL
2. Turn OFF power switch on pump
(LH SIDE SHOWN)
cover (FIG. 46-1).
FIG. 46-1
3. Using the manual backup pump (FIG. 46-
2), lower the platform until inboard rollstop
(IBRS) is locked in the up position (FIG. 47-
1). Refer to Operation Manual for instruc-
tions to operate the manual pump.
RELEASE
VALVE
BACKUP PUMP
HANDLE
USING BACKUP PUMP TO UNFOLD
(LIFT WITH LH PUMP)
FIG. 46-2
PATENTS PENDING
46
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Push the inboard rollstop back
against the lock as if a wheel-
chair is pushing on the rollstop
FIG. 47-1).
PUSH IBRS
AGAINST LOCK
IBRS
PLATFORM BELOW FLOOR LEVEL,
WITH IBRS UP (LH SIDE SHOWN)
FIG. 47-1
5. On the inboard rollstop switch,
loosen screws (1) and (2) one-half
turn (FIG. 47-2B). Next, rotate
switch bracket clockwise until the
switch activates with an audible
“click”. Then tighten screws (1)
and (2) securely.
SCREW (2)
SCREW (1)
SWITCH
(REF)
SWITCH
BRACKET
CUT-AWAY VIEW OF
LH VERTICAL ARM
& IBRS SWITCH
FIG. 47-2B
POWER SWITCH
6. Turn ON power switch on pump
cover (FIG. 47-2A). Then raise
(UP) the platform to floor level
(FIG. 46-1). Verify that “INBD
SW” is not displayed on the lift
controller. If necessary repeat
this procedure.
PLATFORM BELOW FLOOR LEVEL,
WITH IBRS UP (LH SIDE SHOWN)
FIG. 47-2A
PATENTS PENDING
47
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING CONTROLLER TO SPANISH OR ENGLISH (IF REQUIRED)
NOTE: The power switch on the Lift
FOLD
UP
must be turned OFF before
entering SETUP.
1. Turn power switch OFF
(FIG. 48-2).
HAND PENDANT:
ENTERING SETUP
FIG. 48-1
POWER
SWITCH
CONTROLLER
(REF)
2. Enter SETUP by holding
both the UP and FOLD
switches on the hand
pendant (FIG. 48-1) and
turning the power switch
ON at the same time (FIG.
48-2). Controller will
read SETUP (FIG. 48-3).
TURNING POWER SWITCH ON/OFF
(LH PUMP SHOWN)
FIG. 48-2
SETUP
CONTROLLER:
ENTERING SETUP
FIG. 48-3
PATENTS PENDING
48
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Push and release the FOLD
switch (FIG. 49-1). Con-
troller should be in the
LANGUAGE mode (FIG.
49-2).
FOLD
HAND PENDANT:
CHANGING SETUP MODE
FIG. 49-1
LANGUAGE: ENGLISH
CONTROLLER: LANGUAGE
SETTING (ENGLISH OR SPANISH)
FIG. 49-2
NOTE: After you exit SETUP, the con-
troller readings will be displayed
in the language you selected.
4. Push the UP switch or DOWN
switch to change from ENGLISH
to SPANISH (or from SPANISH
to ENGLISH) (FIGS. 49-2 and
49-3).
UP
DOWN
HAND PENDANT:
CHANGING THE SETTING
FIG. 49-3
5. Push and release the FOLD
switch (FIG. 49-1) three
times to exit SETUP (FIG.
49-4).
MAXON LIFT CORP.
CONTROLLER:
EXITING SETUP
FIG. 49-4
PATENTS PENDING
49
Download from Www.Somanuals.com. All Manuals Search And Download.
OUTBOARD ROLLSTOP TIME ADJUSTMENT (IF REQUIRED)
NOTE: Call MAXON Technical Service
FOLD
UP
before doing this adjustment.
NOTE: The power switch on the Lift
must be turned OFF before
entering SETUP.
1. Turn power switch OFF
(FIG. 50-2).
HAND PENDANT:
ENTERING SETUP
FIG. 50-1
POWER
SWITCH
CONTROLLER
(REF)
2. Enter SETUP by holding
both the UP and FOLD
switches on the hand
pendant (FIG. 50-1) and
turning the power switch
ON at the same time (FIG.
50-2). Controller will
read SETUP (FIG. 50-3).
TURNING POWER SWITCH ON/OFF
(LH PUMP SHOWN)
FIG. 50-2
SETUP
CONTROLLER:
ENTERING SETUP
FIG. 50-3
PATENTS PENDING
50
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Push and release the FOLD
switch (FIG. 51-1) to ac-
cess the OUTBD TIME set-
ting (FIG. 51-2).
FOLD
HAND PENDANT:
CHANGING SETUP MODE
FIG. 51-1
NOTE: A larger number for the OUTBD
TIME setting allows more time
for the controller to sense the
outboard rollstop is closed. A
smaller number decreases the
time. Call MAXON Technical
Service to advise you about the
best setting for your vehicle.
OUTBD TIME: 0
CONTROLLER: SETTING
OUTBOARD RAMP TIME
(RANGE IS -7 TO 10)
FIG. 51-2
4. Push the UP switch (FIG. 51-3) to
increase the OUTBD TIME from -7
to 10. Push the DOWN switch (FIG.
51-3) to decrease the number
from 10 to -7.
UP
DOWN
HAND PENDANT:
CHANGING THE SETTING
FIG. 51-3
5. Push and release the FOLD
switch (FIG. 51-1) two
times to exit SETUP (FIG.
51-4).
CONTROLLER:
EXITING SETUP
FIG. 51-4
PATENTS PENDING
51
Download from Www.Somanuals.com. All Manuals Search And Download.
FLOOR POSITION ADJUSTMENT (MANDATORY)
NOTE: Do the following procedure to ensure the inboard rollstop rests on threshold
plate and lines up approximately with edge of base plate.
1. Unfold the platform until the
lights illuminate at floor level or
raise the platform to floor level
EDGE OF
INBOARD
ROLLSTOP
as shown in FIG. 52-1A.
THRESHOLD
PLATE
EDGE OF
BASE PLATE
PLATFORM
LIGHT
INBOARD ROLLSTOP LINES
UP WITH BASE PLATE
FIG. 52-1B
PLATFORM AT FLOOR LEVEL
(LH SIDE SHOWN)
FIG. 52-1A
2. Inspect the threshold plate. The
edge of the inboard rollstop should
line up with the edge of the base
plate as shown in FIG. 52-1B.
PATENTS PENDING
52
Download from Www.Somanuals.com. All Manuals Search And Download.
THRESHOLD
PLATE
EDGE OF
INBOARD
ROLLSTOP
3. If the inboard rollstop does not line up
correctly with the edge of the base plate
(FIGS. 53-1 and 53-2), go to IN-
STRUCTION 4.
EDGE OF
BASE PLATE
INBOARD ROLLSTOP OVERLAPS
EDGE OF BASE PLATE
FIG. 53-1
EDGE OF
INBOARD
ROLLSTOP
THRESHOLD
PLATE
EDGE OF
BASE PLATE
INBOARD ROLLSTOP WITH GAP
BETWEEN BASE PLATE
FIG. 53-2
NOTE: The power switch on the Lift
must be turned OFF before
entering SETUP.
POWER
SWITCH
4. Turn power switch OFF (FIG. 53-3).
CONTROLLER
(REF)
TURNING POWER SWITCH ON/OFF
(LH PUMP SHOWN)
FIG. 53-3
PATENTS PENDING
53
Download from Www.Somanuals.com. All Manuals Search And Download.
FLOOR POSITION ADJUSTMENT - Continued
5. Enter SETUP by holding both
UP
FOLD
the UP and FOLD switches on
the hand pendant (FIG. 54-1)
and turning the power switch
ON at the same time (FIG. 53-
3). Controller will read SETUP
(FIG. 54-2).
HAND PENDANT:
ENTERING SETUP
FIG. 54-1
SETUP
CONTROLLER:
ENTERING SETUP
FIG. 54-2
6. Push and release the FOLD
switch (FIG. 54-3) two
FOLD
times to access the FLOOR
POS setting (FIG. 54-4).
HAND PENDANT:
CHANGING SETUP MODE
FIG. 54-3
FLOOR POS: 345
CONTROLLER:
SETTING FLOOR POSITION
(EXAMPLE READING SHOWN)
FIG. 54-4
PATENTS PENDING
54
Download from Www.Somanuals.com. All Manuals Search And Download.
UP
7. To decrease overlap, push the UP
switch from 1 to 5 times (FIG. 55-1).
The FLOOR POS number displayed on
the controller (FIG. 55-2) will increase
by 1 each time you push the UP but-
ton. To close the gap, push the DOWN
switch from 1 to 5 times (FIG. 55-1).
The FLOOR POS number displayed on
the controller (FIG. 55-2) will decrease
by 1 each time you push the DOWN
button.
DOWN
(-)
HAND PENDANT:
CHANGING THE SETTING
FIG. 55-1
FLOOR POS: 350
CONTROLLER:
SETTING FLOOR POSITION
(EXAMPLE READING SHOWN)
FIG. 55-2
8. Push and release the FOLD
switch (FIG. 55-3) to exit
SETUP (FIG. 55-4).
FOLD
HAND PENDANT:
CHANGING SETUP MODE
FIG. 55-3
MAXON LIFT CORP.
CONTROLLER:
EXITING SETUP
FIG. 55-4
PATENTS PENDING
55
Download from Www.Somanuals.com. All Manuals Search And Download.
FLOOR POSITION ADJUSTMENT - Continued
9. Lower the platform until the inboard
rollstop is in the up and locked posi-
tion. Next, raise the platform to floor
level (FIG. 56-1A). Verify that the
inboard rollstop lines up with the
edge of the base plate as shown in
FIG 56-1B. If necessary, repeat
this entire procedure.
INBOARD
ROLLSTOP
THRESHOLD
PLATE
EDGE OF
BASE PLATE
PLATFORM
LIGHT
INBOARD ROLLSTOP LINES
UP WITH BASE PLATE
FIG. 56-1B
PLATFORM AT FLOOR LEVEL
(LH SIDE SHOWN)
FIG. 56-1A
PATENTS PENDING
56
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM DIAGRAMS
HYDRAULIC SYSTEM DIAGRAM
FLOW CONTROL
VALVE - .5 GPM
FLOW CONTROL
VALVE - .5 GPM
PRESSURE
TRANSDUCER
CYLINDER
CYLINDER
PRESSURE PORT
PRESSURE PORT
MANUAL
RELEASE VALVE
S.V.1
.018 DIA.
S.V.2
MANUAL
BACK-UP
PUMP
RETURN
RETURN
GEAR
PUMP
FILLER -
BREATHER
R.V.
SET @
1550 PSI
FIG. 57-1
PATENTS PENDING
57
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM DIAGRAMS - Continued
ELECTRICAL SYSTEM DIAGRAM
FIG. 58-1
PATENTS PENDING
58
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLETED LIFT INSTALLATION CHECKLIST
† 1. Make sure vehicle is still parked on level ground. If vehicle is equipped with a parking brake, set the
parking brake. If equipped with locking service brake, set the service brake and make sure vehicle is
in park or neutral.
Start vehicle engine.
Turn on Wheelchair Lift power switch (if equipped) at the vehicle driver’s station.
If equipped, make sure occupant restraint belt is buckled on Lift.
Make sure Lift is stowed.
† 2. Turn ON power switch at the Lift. Record CYCLE COUNT _________ and LIFT COUNT _________
indicated on Lift controller.
!
WARNING
The following procedure requires checking equipment on the vehicle while the vehicle is in drive
and parking brake is released. A qualified vehicle operator is needed inside the vehicle at the
driver’s station. A second qualified operator is required outside the vehicle to operate the Wheel-
chair Lift. To prevent accidental injury and equipment damage, chock the vehicle wheels and get a
second qualified vehicle operator to help you do the procedure.
Chock the vehicle wheels.
Check Vehicle Safety Interlocks:
†
3. Make sure the interlock system prevents Lift from being deployed when vehicle is set to move under
its own power. Release the vehicle brakes and/or shift vehicle to a drive gear (DRIVE or REVERSE).
Controller on the Lift should display LOCKED. Try to unfold Lift with the UNFOLD button on hand
pendant. Lift must not unfold from stowed position when vehicle is set to move under its own power.
†
4. Make sure the interlock system prevents vehicle from moving under its own power when the Lift is
deployed. Shift vehicle to PARK or NEUTRAL, and/or set parking brake/service brake as required for
your vehicle interlock system. Lift controller should display STOWED *. Use the UNFOLD button on
hand pendant to unfold the Lift. Release the UNFOLD button when the controller displays UNFOLD.
Try to move vehicle under its own power by shifting into DRIVE and/or releasing parking brake/ser-
vice brake. Vehicle must not be able to shift into DRIVE and/or parking brake/service brake must not
release when Lift is deployed. Make sure vehicle is in PARK or NEUTRAL, and/or parking brake/ser-
vice brake is set as required for your vehicle interlock system. Use the FOLD button to stow the Lift.
The Lift controller displays STOWED * when Lift is stowed and interlock is working correctly.
Check Lift Operation:
NOTE: Keep off the threshold plate until instructed to stand on it.
†
5. Make sure the Lift unfolds all the way to vehicle floor level. Press the UNFOLD button on hand pen-
dant to unfold Lift. Release the UNFOLD button when:
• Platform stops unfolding at vehicle floor level
• Inboard rollstop is lowered to the threshold plate
• Platform lights are illuminated.
The Lift controller displays UNFOLD & FLOOR as Lift moves from stowed position to vehicle floor
level.
†
†
6. Make sure the occupant restraint belt works correctly on the Lift, if equipped. Unbuckle the belt. Then
press the DOWN button on the hand pendant. Lift must not move. Buckle the occcupant restraint belt
before proceeding to the next check.
7. Make sure the threshold warning beacons light up and the alarm sounds when:
• Threshold plate is occupied
• Lift is moving down
Stand on the threshold plate and press the DOWN button on the hand pendant. The controller dis-
plays DOWN as the Lift starts lowering. After the platform is lowered approximately 1” (25mm) below
floor level:
• Threshold warning beacons must light up
• Alarm must sound
• Controller must display MAT ERR
Move off the threshold plate into the vehicle before proceeding to the next check.
PATENTS PENDING
59
Download from Www.Somanuals.com. All Manuals Search And Download.
† 8. Make sure platform lowers all the way to the ground and platform lights are illuminated while platform
is lowering. Press DOWN button on the hand pendant to lower platform to the ground. As the plat-
form is lowering:
• Controller must display DOWN
• Platform lights must be illuminated
When the platform reaches the ground:
• Controller must display GROUND
• Outboard rollstop must lower to the ground
† 9. Make sure platform will not raise more than 3” above the ground if the outboard rollstop is not up all
the way. Stand on the outboard rollstop to keep it from moving to the up position. Press UP button
on hand pendant to raise platform. As the platform is raising:
• Controller must display OUTBD SW
• Platform must stop raising at no more than 3” above the ground
Press the DOWN button on the hand pendant to lower platform to the ground. Move off the outboard
rollstop before proceeding to the next check.
† 10. Make sure platform raises from the ground all the way to vehicle floor level and platform lights are il-
luminated while platform is raising. Press UP button on the hand pendant to raise platform to vehicle
floor level. As the platform is raising:
• Controller must display UP
• Platform lights must be illuminated
When the platform reaches vehicle floor level:
• Controller must display FLOOR
• Platform lights must still be illuminated
† 11. Make sure platform cannot be folded if occupied. Place a 50 pound weight on the platform, on the end
closest to the inboard rollstop. Press FOLD button on the hand pendant.
• Platform must not fold
• Controller must display OCCUPIED
Remove the 50 pound weight from the platform before proceeding to the next check.
† 12. Make sure Lift folds into the stowed position and platform lights turn off. Press FOLD button on the
hand pendant until the Lift is in stowed position and stops folding.
• Controller must display FOLD
• Platform lights must be turned off
• Controller must display STOWED * when Lift is stowed
† 13. Turn the power switch on the Lift controller OFF and then ON again. Check and record CYCLE
COUNT ________ and LIFT COUNT ________ indicated on Lift controller. Both counters must indi-
cate one more count than recorded at the beginning of CHECKLIST.
Check manuals and decals supplied with the Lift:
† 14. All decals are correctly affixed to Lift and on the vehicle. Refer to the DECALS & DECALS PLACE-
MENT section in this manual for decal placement location instructions.
† 15. Lift Operation Manual and Maintenance Schedule are inserted in the vehicle owners manual.
VEHICLE I.D. (VIN)# _______________________________________
WHEELCHAIR LIFT SERIAL# ________________________________
CHECKED BY & DATE: _____________________________________
MAXON LIFT CORP.
A FE SPRINGS, CA 90670
11921 SLAUSON AVE. SANT
.maxonlift.com
16 FAX (888) 771-7713 Internet: www
(562) 464-0099 (800) 227-41
PATENTS PENDING
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Lasko Riding Toy 3542 User Manual
Lenmar Enterprises Battery Charger Speed Charger User Manual
LG Electronics Air Conditioner PRCKD20E User Manual
Lincoln Convection Oven 1421 000 E User Manual
Lindy Network Card 70582 User Manual
Linn Stereo Amplifier PRE AMPLIFIER User Manual
Lux Products Thermostat PSP511 User Manual
Makita Power Hammer HM1306 User Manual
Marshall Amplification Musical Instrument Amplifier G15RCD User Manual
Metrologic Instruments Scanner SP5500 User Manual