INSTRUCTION MANUAL
Demolition Hammer
HM1306
008264
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Secure work.
Use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to
operate the tool.
13. Do not overreach.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be
carried out by qualified persons using original
spare parts, otherwise this may result in
Keep proper footing and balance at all times.
14. Maintain tools with care.
considerable danger to the user.
ENB049-3
Keep cutting tools sharp and clean for better and
safer performance. Follow instructions for
lubrication and changing accessories. Inspect tool
cord periodically and if damaged have it repaired
by an authorized service facility. Inspect extension
cords periodically and replace, if damaged. Keep
handles dry, clean and free from oil and grease.
15. Disconnect tools.
ADDITIONAL SAFETY RULES
1.
2.
3.
Wear ear protectors. Exposure to noise can
cause hearing loss.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly
recommended that you wear a dust mask and
thickly padded gloves.
When not in use, before servicing and when
changing accessories such as blades, bits and
cutters.
4.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
5.
6.
Be sure the bit is secured in place before
operation.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension
cords intended for outdoor use.
19. Stay alert.
Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
7.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of
moving parts, free running of moving parts,
breakage of parts, mounting and any other
conditions that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by an authorized service
center unless otherwise indicated in this
instruction manual. Have defective switches
replaced by an authorized service facility. Do not
use the tool if the switch does not turn it on and
off.
8.
9.
Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
13. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
14. PROPER GROUNDING. This tool should be
grounding while in use to protect the operator
from electric shock.
21. Warning.
The use of any accessory or attachment, other
than those recommended in this instruction
manual or the catalog, may present a risk of
personal injury.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
15. EXTENSION CORDS. Use only three-wire
Installing or removing the bit
extension cords which have three-prong
1. Bull point
grounding-type
plugs
and
three-pole
2. Notched portion
3. Tool retainer
4. Tool holder
1
2
3
receptacles which accept the tool’s plug.
Replace or repair damaged or worn cord
immediately.
16. Do not operate the tool at no-load
unnecessarily.
4
SAVE THESE INSTRUCTIONS.
008266
With the notched portion on the shank of the bit facing
toward the tool retainer, insert the bit into the tool holder
as far as it will go. Then pull out and turn the tool retainer
180° to secure the bit. After installing, always make sure
that the bit is securely held in place by trying to pull it
out.
FUNCTIONAL DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
Side handle (auxiliary handle)
Switch action
1. Side handle
1
1. Lock button
2. Switch trigger
1
2
008267
008265
The side handle swings around to either side, allowing
easy handling of the tool in any position.
CAUTION:
•
Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
OPERATION
Chipping/Scaling/Demolition
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and
then slide down the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
ASSEMBLY
008268
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
Hold the tool firmly with both hands. Turn the tool on and
apply slight pressure on the tool so that the tool will not
bounce around, uncontrolled. Pressing very hard on the
tool will not increase the efficiency.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Oiling
MAINTENANCE
1. Wrench
2. Oil gauge
CAUTION:
1
2
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
Replacing carbon brushes
1. Commutator
2. Insulating tip
3. Carbon brush
008271
2
1
1. Oil supply
1
3
001146
When the resin insulating tip inside the carbon brush is
exposed to contact the commutator, it will automatically
shut off the motor. When this occurs, both carbon
brushes should be replaced. Keep the carbon brushes
clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes.
008272
To replenish, remove the oil gauge with the wrench 23.
Use only Makita genuine oil. The use of any other oil
may harm the tool.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers,
always using Makita replacement parts.
Use a hex-wrentch to remove the holder cap plates.
1. Hex wrench
2. Holder cap plate
1
ACCESSORIES
CAUTION:
•
These
accessories
or
attachments
are
2
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
008269
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones
and secure the brush holder caps.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
1. Screwdriver
2. Brush holder
cap
1
•
•
•
•
•
•
•
•
Bull point
Cold chisel
Scaling chisel
Clay spade
Rammer
Oil supply
Wrench 23
Steel carrying case
2
008270
Reinstall the holder cap plates firmly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Makita Corporation
884757-9
Download from Www.Somanuals.com. All Manuals Search And Download.
|