DS33R11
Ethernet Mapper with Integrated
T1/E1/J1 Transceiver
www.maxim-ic.com
GENERAL DESCRIPTION
FEATURES
ꢀ
10/100 IEEE 802.3 Ethernet MAC (MII and
RMII) Half/Full Duplex with Automatic Flow
Control
The DS33R11 extends a 10/100 Ethernet LAN
segment by encapsulating MAC frames in HDLC or
X.86 (LAPS) for transmission over a T1/E1/J1 data
stream.
ꢀ
ꢀ
Integrated T1/E1/J1 Framer and LIU
The device performs store-and-forward of packets
with full wire-speed transport capability. The built-in
Committed Information Rate (CIR) Controller
provides fractional bandwidth allocation up to the line
rate in increments of 512kbps. The DS33R11 can
operate with an inexpensive external processor.
HDLC/LAPS Encapsulation with
Programmable FCS and Interframe Fill
ꢀ
ꢀ
Committed Information Rate Controller
Provides Fractional Allocations in 512kbps
Increments
Programmable BERT for Serial (TDM)
Interface
APPLICATIONS
Transparent LAN Service
LAN Extension
Ethernet Delivery Over T1/E1/J1
ꢀ
ꢀ
ꢀ
ꢀ
External 16MB, 100MHz SDRAM Buffering
Parallel Microprocessor Interface
1.8V, 3.3V Supplies
FUNCTIONAL DIAGRAM
Reference Design Routes on Two Signal
Layers
ꢀ
IEEE 1149.1 JTAG Support
T1/E1
LINE
T1/E1/J1
TRANSCEIVER
SERIAL STREAM
BERT
ORDERING INFORMATION
PART
TEMP RANGE
PIN-PACKAGE
μC
HDLC/X.86
MAPPER
DS33R11
-40°C to +85°C
256 BGA
SDRAM
10/100
MAC
MII/RMII
10/100
ETHERNET
PHY
DS33R11
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 344
REV: 030807
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.14.1 DTE and DCE Mode .............................................................................................................................58
9.15 ETHERNET MAC ........................................................................................................................... 59
9.15.1 MII Mode Options..................................................................................................................................61
9.15.2 RMII Mode.............................................................................................................................................61
9.15.3 PHY MII Management Block and MDIO Interface ................................................................................62
9.16 BERT IN THE ETHERNET MAPPER ................................................................................................. 62
9.16.1 Receive Data Interface .........................................................................................................................63
9.16.2 Repetitive Pattern Synchronization.......................................................................................................64
9.16.3 Pattern Monitoring.................................................................................................................................64
9.16.4 Pattern Generation................................................................................................................................64
9.17 TRANSMIT PACKET PROCESSOR.................................................................................................... 65
9.18 RECEIVE PACKET PROCESSOR...................................................................................................... 66
9.19 X.86 ENCODING AND DECODING.................................................................................................... 68
9.20 COMMITTED INFORMATION RATE CONTROLLER.............................................................................. 71
10 INTEGRATED T1/E1/J1 TRANSCEIVER ........................................................................................ 72
10.1 T1/E1/J1 CLOCKS ........................................................................................................................ 72
10.2 PER-CHANNEL OPERATION............................................................................................................ 73
10.3 T1/E1/J1 TRANSCEIVER INTERRUPTS............................................................................................ 73
10.4 T1 FRAMER/FORMATTER CONTROL AND STATUS ........................................................................... 74
10.4.1 T1 Transmit Transparency....................................................................................................................74
10.4.2 AIS-CI and RAI-CI Generation and Detection ......................................................................................74
10.4.3 T1 Receive-Side Digital-Milliwatt Code Generation..............................................................................75
10.5 E1 FRAMER/FORMATTER CONTROL AND STATUS........................................................................... 76
10.5.1 Automatic Alarm Generation.................................................................................................................77
10.6 PER-CHANNEL LOOPBACK............................................................................................................. 77
10.7 ERROR COUNTERS........................................................................................................................ 78
10.7.1 Line-Code Violation Counter (TR.LCVCR) ...........................................................................................78
10.7.2 Path Code Violation Count Register (TR.PCVCR)...............................................................................79
10.7.3 Frames Out-of-Sync Count Register (TR.FOSCR) ..............................................................................80
10.7.4 E-Bit Counter (TR.EBCR) .....................................................................................................................80
10.8 DS0 MONITORING FUNCTION ........................................................................................................ 81
10.9 SIGNALING OPERATION ................................................................................................................. 82
10.9.1 Processor-Based Receive Signaling ....................................................................................................82
10.9.2 Hardware-Based Receive Signaling.....................................................................................................83
10.9.3 Processor-Based Transmit Signaling ...................................................................................................84
10.9.4 Hardware-Based Transmit Signaling....................................................................................................85
10.10PER-CHANNEL IDLE CODE GENERATION ........................................................................................ 86
10.10.1 Idle-Code Programming Examples.......................................................................................................87
10.11CHANNEL BLOCKING REGISTERS ................................................................................................... 88
10.12ELASTIC STORES OPERATION........................................................................................................ 88
10.12.1 Receive Elastic Store............................................................................................................................88
10.12.2 Transmit Elastic Store...........................................................................................................................89
10.13G.706 INTERMEDIATE CRC-4 UPDATING (E1 MODE ONLY)............................................................ 90
10.14T1 BIT-ORIENTED CODE (BOC) CONTROLLER............................................................................... 91
10.15RECEIVE BOC .............................................................................................................................. 91
10.16ADDITIONAL (SA) AND INTERNATIONAL (SI) BIT OPERATION (E1 ONLY)........................................... 92
10.17ADDITIONAL HDLC CONTROLLERS IN T1/E1/J1 TRANSCEIVER....................................................... 93
10.17.1 HDLC Configuration..............................................................................................................................93
3 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.17.4 FIFO Information...................................................................................................................................96
10.17.5 Receive Packet-Bytes Available...........................................................................................................96
10.18LEGACY FDL SUPPORT (T1 MODE)............................................................................................... 97
10.19D4/SLC-96 OPERATION................................................................................................................ 98
10.20PROGRAMMABLE IN-BAND LOOP CODE GENERATION AND DETECTION............................................ 99
10.21LINE INTERFACE UNIT (LIU)......................................................................................................... 100
10.21.2 Receiver..............................................................................................................................................100
10.21.3 Transmitter..........................................................................................................................................102
10.22MCLK PRESCALER ..................................................................................................................... 103
10.23JITTER ATTENUATOR................................................................................................................... 103
10.24CMI (CODE MARK INVERSION) OPTION........................................................................................ 103
10.25RECOMMENDED CIRCUITS ........................................................................................................... 104
10.26.6 BERT Alternating Word-Count Rate...................................................................................................110
10.27PAYLOAD ERROR-INSERTION FUNCTION (T1 MODE ONLY) ........................................................... 111
10.28PROGRAMMABLE BACKPLANE CLOCK SYNTHESIZER..................................................................... 112
10.29FRACTIONAL T1/E1 SUPPORT ..................................................................................................... 112
10.30T1/E1/J1 TRANSMIT FLOW DIAGRAMS......................................................................................... 113
11 DEVICE REGISTERS..................................................................................................................... 117
11.1 REGISTER BIT MAPS ................................................................................................................... 118
11.1.1 Global Ethernet Mapper Register Bit Map..........................................................................................118
11.1.2 Arbiter Register Bit Map......................................................................................................................119
11.1.3 BERT Register Bit Map.......................................................................................................................119
11.1.4 Serial Interface Register Bit Map ........................................................................................................120
11.1.5 Ethernet Interface Register Bit Map....................................................................................................122
11.1.6 MAC Register Bit Map ........................................................................................................................123
11.2 GLOBAL REGISTER DEFINITIONS FOR ETHERNET MAPPER............................................................ 134
11.3 ARBITER REGISTERS................................................................................................................... 143
11.3.1 Arbiter Register Bit Descriptions.........................................................................................................143
11.4 BERT REGISTERS ...................................................................................................................... 144
11.5 SERIAL INTERFACE REGISTERS.................................................................................................... 151
11.5.1 Serial Interface Transmit and Common Registers..............................................................................151
11.5.2 Serial Interface Transmit Register Bit Descriptions ............................................................................151
11.5.3 Transmit HDLC Processor Registers..................................................................................................152
11.5.4 X.86 Registers.....................................................................................................................................159
11.5.5 Receive Serial Interface......................................................................................................................161
11.6 ETHERNET INTERFACE REGISTERS .............................................................................................. 174
11.6.1 Ethernet Interface Register Bit Descriptions.......................................................................................174
11.6.2 MAC Registers....................................................................................................................................186
11.7 T1/E1/J1 TRANSCEIVER REGISTERS ........................................................................................... 201
11.7.1 Number-of-Errors Left Register...........................................................................................................299
12 FUNCTIONAL TIMING................................................................................................................... 300
12.1 FUNCTIONAL SERIAL I/O TIMING .................................................................................................. 300
12.2 MII AND RMII INTERFACES .......................................................................................................... 301
12.3 TRANSCEIVER T1 MODE FUNCTIONAL TIMING .............................................................................. 303
4 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
12.4 E1 MODE.................................................................................................................................... 308
13 OPERATING PARAMETERS ........................................................................................................ 313
13.1 THERMAL CHARACTERISTICS....................................................................................................... 314
13.2 MII INTERFACE............................................................................................................................ 315
13.3 RMII INTERFACE......................................................................................................................... 317
13.4 MDIO INTERFACE ....................................................................................................................... 319
13.5 TRANSMIT WAN INTERFACE........................................................................................................ 320
13.6 RECEIVE WAN INTERFACE.......................................................................................................... 321
13.7 SDRAM TIMING.......................................................................................................................... 322
13.8 MICROPROCESSOR BUS AC CHARACTERISTICS........................................................................... 324
13.9 AC CHARACTERISTICS: RECEIVE-SIDE ........................................................................................ 327
13.10AC CHARACTERISTICS: BACKPLANE CLOCK TIMING ..................................................................... 331
13.11AC CHARACTERISTICS: TRANSMIT SIDE....................................................................................... 332
13.12JTAG INTERFACE TIMING............................................................................................................ 335
14 JTAG INFORMATION.................................................................................................................... 336
14.1 JTAG TAP CONTROLLER STATE MACHINE DESCRIPTION............................................................. 337
14.2 INSTRUCTION REGISTER.............................................................................................................. 339
14.3 JTAG ID CODES......................................................................................................................... 341
14.4 TEST REGISTERS ........................................................................................................................ 341
14.4.1 Boundary Scan Register.....................................................................................................................341
14.4.2 Bypass Register..................................................................................................................................341
14.4.3 Identification Register .........................................................................................................................341
14.5 JTAG FUNCTIONAL TIMING ......................................................................................................... 342
15 PACKAGE INFORMATION............................................................................................................ 343
15.1 PACKAGE OUTLINE DRAWING OF 256-BGA (VIEW FROM BOTTOM OF DEVICE).............................. 343
16 DOCUMENT REVISION HISTORY................................................................................................ 344
5 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
LIST OF FIGURES
Figure 6-1. Main Block Diagram................................................................................................................................ 20
Figure 6-3. Receive and Transmit T1/E1/J1 LIU....................................................................................................... 22
Figure 6-4. Receive and Transmit T1/E1/J1 Framer................................................................................................. 23
Figure 6-5. T1/E1/J1 Backplane Interface................................................................................................................. 24
Figure 9-4. IEEE 802.3 Ethernet Frame.................................................................................................................... 56
Figure 9-5. Configured as DTE Connected to an Ethernet PHY in MII Mode........................................................... 58
Figure 9-8. MII Management Frame.......................................................................................................................... 62
Figure 9-13. X.86 Encapsulation of the MAC frame.................................................................................................. 69
Figure 10-1. T1/E1/J1 Clock Map.............................................................................................................................. 72
Figure 10-9. T1 Transmit Pulse Template............................................................................................................... 105
Figure 10-15. Simplified Diagram of BERT in Network Direction............................................................................ 109
Figure 10-17. T1/J1 Transmit Flow Diagram........................................................................................................... 113
Figure 12-2. Rx Serial Interface Functional Timing................................................................................................. 300
Figure 12-8. RMII Transmit Interface Functional Timing......................................................................................... 302
Figure 12-9. RMII Receive Interface Functional Timing.......................................................................................... 303
Figure 12-11. Receive-Side ESF Timing................................................................................................................. 303
Figure 12-16. Transmit-Side ESF Timing................................................................................................................ 306
Figure 12-17. Transmit-Side Boundary Timing (with Elastic Store Disabled)......................................................... 306
6 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-20. Receive-Side Timing......................................................................................................................... 308
Figure 12-21. Receive-Side Boundary Timing (with Elastic Store Disabled).......................................................... 308
Figure 12-25. Transmit-Side Timing........................................................................................................................ 310
Figure 12-27. Transmit-Side Boundary Timing, TSYSCLK = 1.544MHz (Elastic Store Enabled) ......................... 311
Figure 13-5. MDIO Interface Timing........................................................................................................................ 319
Figure 13-6. Transmit WAN Interface Timing.......................................................................................................... 320
Figure 13-7. Receive WAN Interface Timing........................................................................................................... 321
Figure 13-10. Intel Bus Write Timing (MODEC = 00).............................................................................................. 325
Figure 13-13. Receive-Side Timing......................................................................................................................... 328
Figure 13-15. Receive Line Interface Timing .......................................................................................................... 330
Figure 13-16. Receive Timing Delay RCLKO to BPCLK......................................................................................... 331
Figure 13-17. Transmit-Side Timing........................................................................................................................ 333
Figure 14-1. JTAG Functional Block Diagram......................................................................................................... 336
7 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
LIST OF TABLES
Table 2-1. T1-Related Telecommunications Specifications...................................................................................... 16
Table 9-3. Registers Related to Connections and Queues....................................................................................... 52
Table 9-7. MAC Status Registers.............................................................................................................................. 60
Table 10-5 T1 Line Code Violation Counting Options............................................................................................... 78
Table 10-7. T1 Path Code Violation Counting Arrangements................................................................................... 79
Table 10-10. Idle-Code Array Address Mapping....................................................................................................... 86
Table 11-6. Ethernet Interface Register Bit Map..................................................................................................... 122
Table 11-7. MAC Indirect Register Bit Map............................................................................................................. 123
Table 11-8. T1/E1/J1 Transceiver Register Bit Map (Active when CST = 0) .......................................................... 125
Table 13-7. Transmit RMII Interface........................................................................................................................ 317
Table 13-8. Receive RMII Interface......................................................................................................................... 318
Table 13-10. Transmit WAN Interface..................................................................................................................... 320
Table 13-11. Receive WAN Interface...................................................................................................................... 321
Table 13-13. AC Characteristics—Microprocessor Bus Timing.............................................................................. 324
8 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
1 DESCRIPTION
The DS33R11 provides interconnection and mapping functionality between Ethernet Packet Systems and T1/E1/J1
WAN Time-Division Multiplexed (TDM) systems. The device is composed of a 10/100 Ethernet MAC, Packet
Arbiter, Committed Information Rate Controller (CIR), HDLC/X.86 (LAPS) Mapper, SDRAM interface, control ports,
Bit Error Rate Tester (BERT), and integrated T1/E1/J1 Transceiver. The packet interface consists of a MII/RMII
Ethernet PHY interface. The Ethernet interface can be configured for 10Mbit/s or 100Mbit/s service. The DS33R11
encapsulates Ethernet traffic with HDLC or X.86 (LAPS) encoding to be transmitted over a T1, E1, or J1 line. The
T1/E1/J1 interface also receives encapsulated Ethernet packets and transmits the extracted packets over the
Ethernet ports. Access is provided to the signals between the Serial port and the integrated T1/E1/J1 Transceiver.
The device includes a software-selectable T1, E1, or J1 single-chip transceiver (SCT) for short-haul and long-haul
applications. The transceiver is composed of an LIU, framer, and two additional HDLC controllers. The transceiver
is software compatible with the DS2155 and DS2156.
The LIU is composed of transmit and receive interfaces and a jitter attenuator. The transmit interface is responsible
for generating the necessary waveshapes for driving the network and providing the correct source impedance
depending on the type of media used. T1 waveform generation includes DSX-1 line build-outs as well as CSU line
build-outs of -7.5dB, -15dB, and -22.5dB. E1 waveform generation includes G.703 waveshapes for both 75Ω coax
and 120Ω twisted cables. The receive interface provides network termination and recovers clock and data from the
network. The receive sensitivity adjusts automatically to the incoming signal and can be programmed for 0 to 43dB
or 0 to 12dB for E1 applications and 0 to 30dB or 0 to 36dB for T1 applications. The jitter attenuator removes
phase jitter from the transmitted or received signal. The crystal-less jitter attenuator requires only a 2.048MHz
MCLK for both E1 and T1 applications (with the option of using a 1.544MHz MCLK in T1 applications) and can be
placed in either transmit or receive data paths. An additional feature of the LIU is a CMI coder/decoder for
interfacing to optical networks.
On the transmit side, clock, data, and frame-sync signals are provided to the framer by the backplane interface
section. The framer inserts the appropriate synchronization framing patterns, alarm information, calculates and
inserts the CRC codes, and provides the B8ZS/HDB3 (zero code suppression) and AMI line coding. The receive-
side framer decodes AMI, B8ZS, and HDB3 line coding, synchronizes to the data stream, reports alarm
information, counts framing/coding/CRC errors, and provides clock/data and frame-sync signals to the backplane
interface section. Diagnostic capabilities include loopbacks, PRBS pattern generation/detection, and 16-bit loop-up
and loop-down code generation and detection.
Both the transmit and receive path have two HDLC controllers. The HDLC controllers transmit and receive data
through the framer block. The HDLC controllers can be assigned to any time slot, group of time slots, portion of a
time slot or to FDL (T1) or Sa bits (E1). Each controller has 128-byte FIFOs, thus reducing the amount of
processor overhead required to manage the flow of data. In addition, built-in support for reducing the processor
time is required in SS7 applications.
The backplane interface provides a versatile method of sending and receiving data from the host system. Elastic
stores provide a method for interfacing to asynchronous systems, converting from a T1/E1 network to a 2.048MHz,
4.096MHz, 8.192MHz, or N x 64kHz system backplane. The elastic stores also manage slip conditions
(asynchronous interface).
An 8-bit parallel microcontroller port provides access for control and configuration of all the features of the device.
The internal 100MHz SDRAM controller interfaces to a 32-bit wide 128Mb SDRAM. The SDRAM is used to buffer
the data from the Ethernet and WAN ports for transport. The external SDRAM can accommodate up to 8192
frames with a maximum frame size of 2016 bytes. Diagnostic capabilities include SDRAM BIST, loopbacks, PRBS
pattern generation/detection, and 16-bit loop-up and loop-down code generation and detection. The DS33R11
operates with a 1.8V core supply and 3.3V I/O supply.
9 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
The integrated Ethernet Mapper is software compatible with the DS33Z11 Ethernet mapper. There are a few things
to note when porting a DS33Z11 application to this device:
•
•
•
•
•
The SPI and hardware modes are not supported.
RSER has been renamed to RSERI.
RCLK has been renamed to RCLKI.
TSER has been renamed to TSERO.
TCLK has been renamed to TCLKE.
The integrated T1/E1/J1 transceiver is software compatible with the DS2155 T1/E1/J1 transceiver. There are a few
things to note when porting a DS2155 application to this device:
•
The Facilities Data Link (FDL) support is available through software only. The TLINK, RLINK, TLCLK,
RLCLK pins are not available on the DS33R11.
•
•
•
•
Multiplexed Microprocessor Bus mode is not supported on the DS33R11.
The Extended System Information Bus (ESIB) is not supported on the DS33R11.
The MODEC pins serve the function of the DS2155’s BTS pin.
The interim LIU/Framer clock signals RCLKI, RCLKO have been renamed to RDCLKI, RDCLKO to avoid
confusion with the receive clock connections between the transceiver and the Ethernet mapper.
•
The interim LIU/Framer clock signals TCLKI, TCLKO have been renamed to TDCLKI, TDCLKO to avoid
confusion with the receive clock connections between the transceiver and the Ethernet mapper.
•
•
•
•
RSER has been renamed RSERO.
RCLK has been renamed RCLKO.
TSER has been renamed TSERI.
TCLK has been renamed TCLKT.
10 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2 FEATURE HIGHLIGHTS
2.1 General
•
•
•
•
•
•
•
256-pin, 27mm BGA package
1.8V and 3.3V supplies
IEEE 1149.1 JTAG boundary scan
Software access to device ID and silicon revision
Development support includes evaluation kit, driver source code, and reference designs
Reference design routes on a two-layer PC board
Programmable output clocks for fractional T1, E1, H0, and H12 applications
2.2 Microprocessor Interface
•
•
•
•
•
•
Parallel control port with 8-bit data bus
Nonmultiplexed Intel and Motorola timing modes
Internal software reset and external hardware reset-input pin
Supports polled or interrupt-driven environments
Software access to device ID and silicon revision
Global interrupt-output pin
2.3 HDLC Ethernet Mapping
•
•
•
•
•
•
•
•
•
•
Dedicated HDLC controller engine for protocol encapsulation
Compatible with polled or interrupt driven environments
Programmable FCS insertion and extraction
Programmable FCS type
Supports FCS error insertion
Programmable packet size limits (Minimum 64 bytes and maximum 2016 bytes)
Supports bit stuffing/destuffing
Selectable packet scrambling/descrambling (X43+1)
Separate FCS errored packet and aborted packet counts
Programmable inter-frame fill for transmit HDLC
2.4 X.86 (Link Access Protocol for SONET/SDH) Ethernet Mapping
•
•
•
•
•
•
•
•
•
•
•
Programmable X.86 address/control fields for transmit and receive
Programmable 2-byte protocol (SAPI) field for transmit and receive
32 bit FCS
Transmit transparency processing—7E is replaced by 7D, 5E
Transmit transparency processing—7D replaced by 7D, 5D
Receive rate adaptation (7D, DD) is deleted.
Receive transparency processing—7D, 5E is replaced by 7E
Receive transparency processing—7D, 5D is replaced by 7D
Receive abort sequence the LAPS packet is dropped if 7D7E is detect
Self-synchronizing X43+1 payload scrambling.
Frame indication due to bad address/control/SAPI, FCS error, abort sequence or frame size longer
than preset max
11 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.5 Additional HDLC Controllers in the Integrated T1/E1/J1 Transceiver
•
•
•
•
•
•
•
•
Two additional independent HDLC controllers
Fast load and unload features for FIFOs
SS7 support for FISU transmit and receive
Independent 128-byte Rx and Tx buffers with interrupt support
Access FDL, Sa, or single/multiple DS0 channels
DS0 access includes Nx64 or Nx56
Compatible with polled or interrupt driven environments
Bit-oriented code (BOC) support
2.6 Committed Information Rate (CIR) Controller
•
•
•
CIR Rate controller limits transmission of data from the Ethernet interface to the serial interface
CIR granularity at 512kbit/s
CIR averaging for smoothing traffic peaks
2.7 SDRAM Interface
•
•
•
•
•
•
Interface for 128Mb, 32-bit-wide SDRAM
SDRAM Interface speed up to 100MHz
Auto refresh timing
Automatic precharge
Master clock provided to the SDRAM
No external components required for SDRAM connectivity
2.8 MAC Interface
•
•
•
•
•
•
•
•
•
MAC port with standard MII (less TX_ER) or RMII
10Mbps and 100Mbps Data rates
Configurable DTE or DCE modes
Facilitates auto-negotiation by host microprocessor
Programmable half and full-duplex modes
Flow control for both half-duplex (back-pressure) and full-duplex (PAUSE) modes
Programmable Maximum MAC frame size up to 2016 bytes
Minimum MAC frame size: 64 bytes
Discards frames greater than programmed maximum MAC frame size and runt, nonoctet bounded, or
bad-FCS frames upon reception
•
•
•
Configurable for promiscuous broadcast-discard mode.
Programmable threshold for SDRAM queues to initiate flow control and status indication
MAC loopback support for transmit data looped to receive data at the MII/RMII interface
12 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.9 T1/E1/J1 Line Interface
•
Requires only a 2.048MHz master clock for both E1 and T1 operation with the option to use 1.544MHz
for T1 operation
•
•
•
•
Fully software configurable
Short-haul and long-haul applications
Automatic receive sensitivity adjustments
Ranges include 0 to 43dB or 0 to 12dB for E1 applications and 0 to 13dB or 0 to 36dB for T1
applications
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Receive level indication in 2.5dB steps from -42.5dB to -2.5dB
Internal receive termination option for 75Ω, 100Ω, and 120Ω lines
Internal transmit termination option for 75Ω, 100Ω, and 120Ω lines
Monitor application gain settings of 20dB, 26dB, and 32dB
G.703 receive synchronization-signal mode
Flexible transmit waveform generation
T1 DSX-1 line build-outs
T1 CSU line build-outs of -7.5dB, -15dB, and -22.5dB
E1 waveforms include G.703 waveshapes for both 75Ω coax and 120Ω twisted cables
AIS generation independent of loopbacks
Alternating ones and zeros generation
Square-wave output
Open-drain output option
NRZ format option
Transmitter power-down
Transmitter 50mA short-circuit limiter with current-limit-exceeded indication
Transmit open-circuit-detected indication
Line interface function can be completely decoupled from the framer/formatter
2.10 Clock Synthesizer
•
•
Output frequencies include 2.048MHz, 4.096MHz, 8.192MHz, and 16.384MHz
Derived from recovered receive clock
2.11 Jitter Attenuator
•
•
32-bit or 128-bit crystal-less jitter attenuator
Requires only a 2.048MHz master clock for both E1 and T1 operation with the option to use 1.544MHz
for T1 operation
•
•
Can be placed in either the receive or transmit path or disabled
Limit trip indication
13 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.12 T1/E1/J1 Framer
•
•
•
•
•
Fully independent transmit and receive functionality
Full receive and transmit path transparency
T1 framing formats include D4 (SLC-96) and ESF
Detailed alarm and status reporting with optional interrupt support
Large path and line error counters for:
o
o
T1: BPV, CV, CRC6, and framing bit errors
E1: BPV, CV, CRC4, E-bit, and frame alignment errors
•
•
Timed or manual update modes
DS1 idle code generation on a per-channel basis in both transmit and receive paths
o
o
User-defined
Digital milliwatt
•
•
•
•
•
•
•
ANSI T1.403-1998 Support
RAI-CI detection and generation
AIS-CI detection and generation
E1 ETS 300 011 RAI generation
G.965 V5.2 link detect
Ability to monitor one DS0 channel in both the transmit and receive paths
In-band repeating pattern generators and detectors
o
o
Three independent generators and detectors
Patterns from 1 to 8 bits or 16 bits in length
•
•
RCL, RLOS, RRA, and RAIS alarms interrupt on change-of-state
Flexible signaling support
o
o
o
Software or hardware based
Interrupt generated on change of signaling data
Receive signaling freeze on loss-of-sync, carrier loss, or frame slip
•
•
•
•
•
Addition of hardware pins to indicate carrier loss and signaling freeze
Automatic RAI generation to ETS 300 011 specifications
Access to Sa and Si bits
Option to extend carrier loss criteria to a 1ms period as per ETS 300 233
Japanese J1 support
o
o
Ability to calculate and check CRC6 according to the Japanese standard
Ability to generate Yellow Alarm according to the Japanese standard
2.13 TDM Bus
•
Dual two-frame independent receive and transmit elastic stores
o
o
o
Independent control and clocking
Controlled slip capability with status
Minimum delay mode supported
•
•
Programmable output clocks for fractional T1, E1, H0, and H12 applications
Hardware signaling capability
o
o
o
Receive signaling reinsertion to a backplane multiframe sync
Availability of signaling in a separate PCM data stream
Signaling freezing
•
•
•
Ability to pass the T1 F-bit position through the elastic stores in the 2.048MHz backplane mode
Access to the data streams in between the framer/formatter and the elastic stores
User-selectable synthesized clock output
14 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.14 Test and Diagnostics
•
•
•
•
•
•
•
•
•
•
•
•
•
IEEE 1149.1 support
Programmable on-chip bit error-rate tester (BERT)
Pseudorandom patterns including QRSS
User-defined repetitive patterns
Daly pattern
Error insertion single and continuous
Total bit and errored bit counts
Payload error insertion
Error insertion in the payload portion of the T1 frame in the transmit path
Errors can be inserted over the entire frame or selected channels
Insertion options include continuous and absolute number with selectable insertion rates
F-bit corruption for line testing
Loopbacks: remote, local, analog, and per-channel loopback
15 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
2.15 Specifications Compliance
The DS33R11 meets relevant telecommunications specifications. The following table provides the specifications
and relevant sections that are applicable to the DS33R11.
Table 2-1. T1-Related Telecommunications Specifications
IEEE 802.3-2002—CSMA/CD access method and physical layer specifications.
RFC1662—PPP in HDLC-like Framing
RFC2615—PPP over SONET/SDH
X.86—Ethernet over LAPS
RMII—Industry Implementation Agreement for “Reduced MII Interface,” Sept 1997
ANSI: T1.403-1995, T1.231–1993, T1.408
AT&T: TR54016, TR62411
ITU-T: G.703, G.704, G.706, G.736, G.775, G.823, G.932, I.431, O.151, Q.161,
Recommendation I.432–03/93 B-ISDN User-Network Interface—Physical Layer Specification
ETSI: ETS 300 011, ETS 300 166, ETS 300 233, CTR12, CTR4
Japanese: JTG.703, JTI.431, JJ-20.11 (CMI Coding Only)
16 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
3 APPLICATIONS
The DS33R11 is ideal for application areas such as transparent LAN service, LAN extension, and Ethernet delivery
over T1/E1/J1, T3/E3, OC-1/EC-1, G.SHDSL, or HDSL2/4.
For an example of a complete LAN-to-WAN design, refer to Application Note 3411: DS33Z11—Ethernet LAN to
Figure 3-1. Ethernet-to-WAN Extension (With or Without Framing)
RMII, MII
T1/E1/J1
10 Base T
Stream
100 Base T
Inter-Building
LAN Extension
DS33R11
Ethernet
Clock
Sources
SDRAM
17 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
4 ACRONYMS AND GLOSSARY
•
•
•
•
•
•
•
•
•
BERT: Bit Error-Rate Tester
DCE: Data Communication Interface
DTE: Data Terminating Interface
FCS: Frame Check Sequence
HDLC: High-Level Data Link Control
MAC: Media Access Control
MII: Media Independent Interface
RMII: Reduced Media Independent Interface
WAN: Wide Area Network
Note 1: Previous versions of this document used the term “Subscriber” to refer to the Ethernet Interface function.
The register names have been allowed to remain with a “SU.” prefix to avoid register renaming.
Note 2: Previous versions of this document used the term “Line” to refer to the Serial Interface. The register names
have been allowed to remain with a “LI.” prefix to avoid register renaming.
Note 3: The terms “Transmit Queue” and “Receive Queue” are with respect to the Ethernet Interface. The Receive
Queue is the queue for the data that arrives on the MII/RMII interface, is processed by the MAC and stored in the
SDRAM. Transmit queue is for data that arrives from the Serial port, is processed by the HDLC and stored in the
SDRAM to be sent to the MAC transmitter.
Note 4: This data sheet assumes a particular nomenclature of the T1 operating environment. In each 125μs frame
there are 24 8-bit channels plus a framing bit. It is assumed that the framing bit is sent first followed by channel 1.
Each channel is made up of eight bits that are numbered 1 to 8. Bit number 1 is the MSB and is transmitted first.
Bit number 8 is the LSB and is transmitted last. The term “locked” is used to refer to two clock signals that are
phase- or frequency-locked or derived from a common clock (i.e., a 1.544MHz clock can be locked to a 2.048MHz
clock if they share the same 8kHz component). Throughout this data sheet, the following abbreviations are used:
B8ZS
BOC
CRC
D4
Bipolar with 8 Zero Substitution
Bit-Oriented Code
Cyclical Redundancy Check
Superframe (12 frames per multiframe) Multiframe Structure
Extended Superframe (24 frames per multiframe) Multiframe Structure
Facility Data Link
ESF
FDL
FPS
Fs
Framing Pattern Sequence in ESF
Signaling Framing Pattern in D4
Terminal Framing Pattern in D4
High-Level Data Link Control
Ft
HDLC
MF
Multiframe
SLC–96
Subscriber Loop Carrier—96 Channels
18 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
5 MAJOR OPERATING MODES
Microprocessor control is possible through the 8-bit parallel control port and provides configuration for all the
features of the device. The Ethernet Link Transport Engine in the device can be configured for HDLC or X.86
encapsulation.
The integrated transceiver can be software configured for T1, E1, or J1 operation. It is composed of a line interface
unit (LIU), framer, two additional HDLC controllers, and a TDM backplane interface, and is controlled via an 8-bit
parallel port configured for Intel or Motorola bus operations.
The LIUs are composed of a transmit interface, receive interface, and a jitter attenuator. The transmit interface is
responsible for generating the necessary waveshapes for driving the network and providing the correct source
impedance depending on the type of media used. T1 waveform generation includes DSX-1 line build-outs as well
as CSU line build-outs of -7.5dB, -15dB, and -22.5dB. E1 waveform generation includes G.703 waveshapes for
both 75Ω coax and 120Ω twisted cables. The receive interface provides network termination and recovers clock
and data from the network. The receive sensitivity adjusts automatically to the incoming signal and can be
programmed for 0dB to 43dB or 0dB to 12dB for E1 applications and 0dB to 15dB or 0dB to 36dB for T1
applications. The jitter attenuator removes phase jitter from the transmitted or received signal. The crystal-less jitter
attenuator requires only a 2.048MHz MCLK for both E1 and T1 applications (with the option of using a 1.544MHz
MCLK in T1 applications) and can be placed in either transmit or receive data paths.
19 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
6 BLOCK DIAGRAMS
Figure 6-1. Main Block Diagram
μP Port
CLAD
CLAD
SYSCLKI
(RMII MODE)
RXD[0:1]
RX_CLK
CRS_DV
RX_ERR
TTIP
MUX
TRING
HDLC
REF_CLK
REF_CLKO
BERT
ARBITER
HDLC
TX_EN
TXD[0:1]
RTIP
MUX
RRING
MDC
MDIO
JTAG2
JTAG1
SDRAM PORT
NOTE: SOME PINS NOT SHOWN. THE BLOCK IN THE DIAGRAM LABELED “T1/E1/J1 TRANSCEIVER” IS
DIVIDED INTO THREE FUNCTIONAL BLOCKS: LIU, FRAMER, AND BACKPLANE INTERFACE OUTLINED IN
THE FOLLOWING DIAGRAMS.
20 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 6-2. Block Diagram of T1/E1/J1 Transceiver
CLOCK
EXTERNAL ACCESS
TO RECEIVE SIGNALS
CLOCK
ADAPTER
HDB3 / B8ZS
SYNC
BACKPLANE
CLOCK SYNTH
RX
LIU
MUX
SINGALING
ALARM DET
HDLCs
BACKPLANE
INTERFACE
CIRCUIT
FRAMER
SINGALING
ALARM GEN
HDLCs
TX
LIU
MUX
CRC GEN
HDB3 / B8ZS
EXTERNAL ACCESS
TO TRANSMIT SIGNALS
LIU
FRAMER
BACKPLANE
INTERFACE
JTAG HOST INTERFACE ESIB
21 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 6-4. Receive and Transmit T1/E1/J1 Framer
REC
REC
HDLC #1
HDLC #2
128 Byte
FIFO
128 Byte
FIFO
MAPPER
MAPPER
DATA
CLOCK
SYNC
DATA
CLOCK
SYNC
SYNC
CLOCK
DATA
RPOS
RNEG
RCLK
RECEIVE
FRAMER
SYNC
TPOS
TNEG
TCLK
TRANSMIT
FRAMER
CLOCK
DATA
MAPPER
MAPPER
INTERNAL
SIGNALS
FROM
INTERNAL
SIGNALS
TO
BACKPLANE
INTERFACE
XMIT
HDLC #1
XMIT
HDLC #2
LIU
128 Byte
FIFO
128 Byte
FIFO
23 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 6-5. T1/E1/J1 Backplane Interface
Sa BIT/FDL
EXTRACTION
RLINK
RLCLK
RSIG
RSIGFR
SIGNALING
BUFFER
DATA
CLOCK
SYNC
RSYSCLK
RSERO
RCLKO
RSYNC
RMSYNC
ELASTIC
STORE
RFSYNC
RDATA
INTERNAL
SIGNALS
FROM
RCHCLK
RCHBLK
CHANNEL
TIMING
FRAMER
SYNC
TSERI
TSIG
TSSYNC
SIGNALING
BUFFER
Sa/FDL
INSERT
ELASTIC
STORE
DATA
TSYSCLK
TSYNC
CLOCK
TESO
TDATA
TLCLK
TLINK
CHANNEL
TIMING
TCHCLK
TCHBLK
TCLK
MUX
TCLKT
JACLK
24 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
7 PIN DESCRIPTIONS
7.1 Pin Functional Description
Note that all digital pins are IO pins in JTAG mode. This feature increases the effectiveness of board level ATPG
patterns.
LEGEND: I = input, O = output, Ipu = input with pullup, Oz = output with tri-state, IO = bidirectional pin, IOz = bidirectional pin with tri-state.
Table 7-1. Detailed Pin Descriptions
NAME
PIN
TYPE
FUNCTION
MICROPROCESSOR PORT
Address Bit 0: Address bit 0 of the microprocessor interface.
Least Significant Bit.
A0
A18
I
A1
A2
A3
A4
A5
A6
A7
A8
A9
B18
C18
A17
B17
C17
A16
B16
C16
C15
I
I
I
I
I
I
I
I
I
Address Bit 1: Address bit 1 of the microprocessor interface.
Address Bit 2: Address bit 2 of the microprocessor interface.
Address Bit 3: Address bit 3 of the microprocessor interface.
Address Bit 4: Address bit 4 of the microprocessor interface.
Address Bit 5: Address bit 5 of the microprocessor interface.
Address Bit 6: Address bit 6 of the microprocessor interface.
Address Bit 7: Address bit 7 of the microprocessor interface.
Address Bit 8: Address bit 8 of the microprocessor interface.
Address Bit 9: Address bit 9 of the microprocessor interface.
Data Bit 0: Bidirectional data bit 0 of the microprocessor interface.
Least Significant Bit. Not driven when CS =1 or RST = 0.
Data Bit 1: Bidirectional data bit 1 of the microprocessor interface.
Not driven when CS = 1 or RST = 0.
Data Bit 2: Bidirectional data bit 2 of the microprocessor interface.
Not driven when CS = 1 or RST = 0.
Data Bit 3: Bidirectional data bit 3 of the microprocessor interface.
Not driven when CS = 1 or RST = 0.
Data Bit 4: Bidirectional data bit 4 of the microprocessor interface.
Not driven when CS = 1 or RST = 0.
Data Bit 5: Bidirectional data bit 5 of the microprocessor interface.
Not driven when CS = 1 or RST = 0.
D0
D1
D2
D3
D4
D5
D6
D7
A14
B14
C14
A13
B13
C13
A12
B12
IOZ
IOZ
IOZ
IOZ
IOZ
IOZ
IOZ
IOZ
Data Bit 6: Bidirectional data bit 6 of the microprocessor interface.
Not driven when CS = 1 or RST = 0.
Data Bit 7: Bidirectional data bit 7 of the microprocessor interface.
Most Significant Bit. Not driven when CS = 1 or RST = 0.
Write (Intel Mode): The DS33R11 captures the contents of the
data bus (D0-D7) on the rising edge of WR and writes them to the
addressed register location. CS must be held low during write
operations.
C11
I
WR/RW
Read Write (Motorola Mode): Used to indicate read or write
operation. RW must be set high for a register read cycle and low for
a register write cycle.
25 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
Read Data Strobe (Intel Mode): The DS33R11 drives the data bus
(D0-D7) with the contents of the addressed register while RD and
CS are both low.
B11
I
RD/DS
Data Strobe (Motorola Mode): Used to latch data through the
microprocessor interface. DS must be low during read and write
operations.
Chip Select for Protocol Conversion Device: This pin must be
taken low for read/write operations. When CS is high, the RD/DS
and WR signals are ignored.
A11
D7
I
I
CS
Chip Select for the T1/E1/J1 Transceiver: Must be low to read or
write the T1/E1/J1 transceiver.
CST
Interrupt Output: Outputs a logic zero when an unmasked
interrupt event is detected. INT is deasserted when all interrupts
have been acknowledged and serviced. Active low. Inactive state is
interrupts have been acknowledged and serviced. Active low.
A10
OZ
INT
26 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
MII/RMII PHY PORT
Collision Detect (MII): Asserted by the MAC PHY to indicate that a
collision is occurring. In DCE Mode this signal should be connected
to ground. This signal is only valid in half duplex mode, and is
ignored in full duplex mode.
COL_DET
N18
I
Receive Carrier Sense (MII): Should be asserted (high) when data
from the PHY (RXD[3:0) is valid. For each clock pulse 4 bits arrive
from the PHY. Bit 0 is the least significant bit. In DCE mode,
connect to VDD.
RX_CRS/
CRS_DV
M19
M20
I
Carrier Sense/Receive Data Valid (RMII): This signal is asserted
(high) when data is valid from the PHY. For each clock pulse 2 bits
arrive from the PHY. In DCE mode, this signal must be grounded.
Receive Clock (MII): Timing reference for RX_DV, RX_ERR and
RXD[3:0], which are clocked on the rising edge. RX_CLK frequency
is 25MHz for 100Mbit/s operation and 2.5MHz for 10Mbit/s
operation. In DTE mode, this is a clock input provided by the PHY.
In DCE mode, this is an output derived from REF_CLK providing
2.5MHz (10Mbit/s operation) or 25MHz (100Mbit/s operation).
RX_CLK
IO
Receive Data 0 through 3 (MII): Four bits of received data,
sampled synchronously with the rising edge of RX_CLK. For every
clock cycle, the PHY transfers 4 bits to the DS33R11. RXD[0] is the
least significant bit of the data. Data is not considered valid when
RX_DV is low.
RXD[0]
RXD[1]
RXD[2]
RXD[3]
L18
L19
L20
M18
O
Receive Data 0 through 1 (RMII): Two bits of received data,
sampled synchronously with REF_CLK with 100Mbit/s mode.
Accepted when CRS_DV is asserted. When configured for
10Mbit/s mode, the data is sampled once every 10 clock periods.
Receive Data Valid (MII): This active high signal indicates valid
data from the PHY. The data RXD is ignored if RX_DV is not
asserted high.
RX_DV
K19
I
I
Receive Error (MII): Asserted by the MAC PHY for one or more
RX_CLK periods indicating that an error has occurred. Active High
indicates Receive code group is invalid. If CRS_DV is low,
RX_ERR has no effect. This is synchronous with RX_CLK. In DCE
mode, this signal must be grounded.
RX_ERR
K18
Receive Error (RMII): Signal is synchronous to REF_CLK.
Transmit Clock (MII): Timing reference for TX_EN and TXD[3:0].
The TX_CLK frequency is 25MHz for 100Mbit/s operation and
2.5MHz for 10Mbit/s operation.
TX_CLK
H19
IO
In DTE mode, this is a clock input provided by the PHY. In DCE
mode, this is an output derived from REF_CLK providing 2.5MHz
(10Mbit/s operation) or 25MHz (100Mbit/s operation).
27 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
Transmit Data 0 through 3(MII): TXD [3:0] is presented
synchronously with the rising edge of TX_CLK. TXD [0] is the least
significant bit of the data. When TX_EN is low the data on TXD
should be ignored.
TXD[0]
F19
TXD[1]
TXD[2]
F18
E20
O
Transmit Data 0 through 1(RMII): Two bits of data TXD [1:0]
presented synchronously with the rising edge of REF_CLK.
TXD[3]
TX_EN
E19
F20
Transmit Enable (MII): This pin is asserted high when data TXD
[3:0] is being provided by the DS33R11. The signal is deasserted
prior to the first nibble of the next frame. This signal is synchronous
with the rising edge TX_CLK. It is asserted with the first bit of the
preamble.
O
Transmit Enable (RMII): When this signal is asserted, the data on
TXD [1:0] is valid. This signal is synchronous to the REF_CLK.
Reference Clock (RMII and MII): When in RMII mode, all signals
from the PHY are synchronous to this clock input for both transmit
and receive. This required clock can be up to 50MHz and should
have ±100ppm accuracy.
When in MII mode in DCE operation, the DS33R11 uses this input
to generate the RX_CLK and TX_CLK outputs as required for the
Ethernet PHY interface. When the MII interface is used with DTE
operation, this clock is not required and should be tied low.
REF_CLK
A19
A20
I
In DCE and RMII modes, this input must have a stable clock input
before setting the RST pin high for normal operation.
Reference Clock Output (RMII and MII): A derived clock output
up to 50MHz, generated by internal division of the SYSCLKI signal.
Frequency accuracy of the REF_CLKO signal will be proportional
to the accuracy of the user-supplied SYSCLKI signal. See Section
9.1.1 for more information.
REF_CLKO
O
DCE or DTE Selection: The user must set this pin high for DCE
Mode selection or low for DTE Mode. In DCE Mode, the DS33R11
MAC port can be directly connected to another MAC. In DCE
Mode, the Transmit clock (TX_CLK) and Receive clock (RX_CLK)
are output by the DS33R11. Note that there is no software bit
selection of DCEDTES. Note that DCE Mode is only relevant when
the MAC interface is in MII mode.
DCEDTES
RMIIMIIS
G20
G19
I
I
RMII or MII Selection: Set high to configure the MAC for RMII
interfacing. Set low for MII interfacing.
28 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
PHY MANAGEMENT BUS
Management Data Clock (MII): Clocks management data between
the PHY and DS33R11. The clock is derived from theSYSCLKI,
with a maximum frequency is 1.67MHz. The user must leave this
pin unconnected in the DCE Mode.
MDC
C19
O
MII Management data IO (MII): Data path for control information
between the PHY and DS33R11. When not used, pull to logic high
externally through a 10kΩ resistor. The MDC and MDIO pins are
used to write or read up to 32 Control and Status Registers in 32
PHY Controllers. This port can also be used to initiate Auto-
Negotiation for the PHY. The user must leave this pin unconnected
in the DCE Mode.
MDIO
C20
IO
SDRAM INTERFACE
SDRAM Column Address Strobe: Active-low output, used to latch
the column address on the rising edge of SDCLKO. It is used with
commands for Bank Activate, Precharge, and Mode Register Write.
W7
W9
O
O
SCAS
SRAS
SDRAM Row Address Strobe: Active-low output, used to latch
the row address on rising edge of SDCLKO. It is used with
commands for Bank Activate, Precharge, and Mode Register Write.
V10
O
O
SDRAM Chip Select: Active-low output enables SDRAM access.
SDCS
SWE
SDRAM Write Enable: This active-low output enables write
operation and auto precharge.
W10
SDRAM Bank Select: These 2 bits select 1 of 4 banks for the
read/write/precharge operations.
SBA[0]
SBA[1]
Y11
V11
O
Note: All SDRAM operations are controlled entirely by the
DS33R11. No user programming for SDRAM buffering is required.
29 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
SDATA[0]
SDATA[1]
SDATA[2]
SDATA[3]
SDATA[4]
SDATA[5]
SDATA[6]
SDATA[7]
SDATA[8]
SDATA[9]
SDATA[10]
SDATA[11]
SDATA[12]
SDATA[13]
SDATA[14]
SDATA[15]
SDATA[16]
SDATA[17]
SDATA[18]
SDATA[19]
SDATA[20]
SDATA[21]
SDATA[22]
SDATA[23]
SDATA[24]
SDATA[25]
SDATA[26]
SDATA[27]
SDATA[28]
SDATA[29]
SDATA[30]
SDATA[31]
SDA[0]
PIN
W2
Y4
Y2
Y5
Y3
W5
V5
W6
V6
W4
V4
V2
V3
V1
W3
W1
Y16
Y17
V18
Y19
V19
Y20
U19
W20
U20
T19
T20
Y18
W19
V17
W17
W16
W14
W12
Y15
W15
Y14
V13
W13
Y12
V12
Y10
V14
W11
Y6
TYPE
FUNCTION
SDRAM Data Bus Bits 0 to 31: The 32 pins of the SDRAM data
bus are inputs for read operations and outputs for write operations.
At all other times, these pins are high-impedance.
O
Note: All SDRAM operations are controlled entirely by the
DS33R11. No user programming for SDRAM buffering is required.
SDA[1]
SDA[2]
SDA[3]
SDA[4]
SDA[5]
SDA[6]
SDA[7]
SDA[8]
SDRAM Address Bus 0 to 11: The 12 pins of the SDRAM address
bus output the row address first, followed by the column address.
The row address is determined by SDA0 to SDA11 at the rising
edge of clock. Column address is determined by SDA0-SDA9 and
SDA11 at the rising edge of the clock. SDA10 is used as an auto-
precharge signal.
O
O
Note: All SDRAM operations are controlled entirely by the
DS33R11. No user programming for SDRAM buffering is required.
SDA[9]
SDA[10]
SDA[11]
SDMASK[0]
SDMASK[1]
SDMASK[2]
SDMASK[3]
SDRAM Mask 0 through 3: When high, a write is done for that
byte. The least significant byte is SDATA7 to SDATA0. The most
significant byte is SDATA31 to SDATA24.
V7
V16
V15
O
(4mA)
SDRAM CLK Out: System clock output to the SDRAM. This clock
is a buffered version of SYSCLKI.
SDCLKO
Y8
30 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
TTIP
PIN
TYPE
O
FUNCTION
T1/E1/J1 ANALOG LINE INTERFACE
Transmit Analog Tip Output for the T1/E1/J1 Transceiver:
Analog line-driver outputs. Two connections are provided to
improve signal quality. These pins connect via a 1:2 step-up
Transmit Analog Ring Output for the T1/E1/J1 Transceiver:
Analog line-driver outputs. Two connections are provided to
improve signal quality. These pins connect via a 1:2 step-up
Receive Analog Tip Input for the T1/E1/J1 Transceiver: Analog
input for clock recovery circuitry. These pins connect via a 1:1
Receive Analog Ring Input for the T1/E1/J1 Transceiver:
Analog input for clock recovery circuitry. These pins connect via a
R1, R2
T1,T2
TRING
O
RTIP
K1
I
I
RRING
M1
T1/E1/J1 TRANSMIT FRAMER INTERFACE
Transmit Serial Data Input to the T1/E1/J1 Framer: Transmit
NRZ serial data. Sampled on the falling edge of TCLKT when the
transmit-side elastic store is disabled. Sampled on the falling edge
of TSYSCLK when the transmit-side elastic store is enabled.
Transmit Clock for the T1/E1/J1 Transceiver: 1.544MHz or a
2.048MHz primary clock. Used to clock data from the TSERI pin
through the transmit-side formatter.
TSERI
TCLKT
E3
D2
I
I
Transmit Channel Block for the T1/E1/J1 Transceiver: A user-
programmable output that can be forced high or low during any of
the channels. Synchronous with TCLKT when the transmit-side
elastic store is disabled. Synchronous with TSYSCLK when the
transmit-side elastic store is enabled. Useful for locating individual
channels in drop-and-insert applications, for external per-channel
loopback, and for per-channel conditioning.
Transmit Channel Clock for the T1/E1/J1 Transceiver: A
192kHz (T1) or 256kHz (E1) clock that pulses high during the LSB
of each channel. Can also be programmed to output a gated
transmit-bit clock for fractional T1/E1 applications. Synchronous
with TCLKT when the transmit-side elastic store is disabled.
Synchronous with TSYSCLK when the transmit-side elastic store is
enabled. Useful for parallel-to-serial conversion of channel data.
Transmit System Sync for the T1/E1/J1 Transceiver: Only used
when the transmit-side elastic store is enabled. A pulse at this pin
will establish either frame or multiframe boundaries for the transmit
side. Should be tied low in applications that do not use the transmit-
side elastic store.
Transmit Sync for the T1/E1/J1 Transceiver: A pulse at this pin
will establish either frame or multiframe boundaries for the transmit
side. Can be programmed to output either a frame or multiframe
pulse. If this pin is set to output pulses at frame boundaries, it can
also be set via TR.IOCR1.3 to output double-wide pulses at
signaling frames in T1 mode.
Transmit System Clock for the T1/E1/J1 Transceiver:
1.544MHz, 2.048MHz, 4.096MHz, 8.192MHz, or 16.384MHz clock.
Only used when the transmit-side elastic-store function is enabled.
Should be tied low in applications that do not use the transmit-side
elastic store.
TCHBLK
TCHCLK
A2
G1
O
O
TSSYNC
TSYNC
A5
C1
E4
I
I/O
I
TSYSCLK
31 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
Transmit Signaling Input for the T1/E1/J1 Transceiver: When
enabled, this input will sample signaling bits for insertion into
outgoing PCM data stream. Sampled on the falling edge of TCLKT
when the transmit-side elastic store is disabled. Sampled on the
falling edge of TSYSCLK when the transmit-side elastic store is
enabled.
TSIG
B4
I
ETHERNET MAPPER TRANSMIT SERIAL INTERFACE
Transmit Serial Data Output from Ethernet Mapper: Output on
the rising edge of TCLKE. Selective clock periods can be skipped
for output of TSERO with a gapped clock input on TCLKE. The
maximum data rate is 52Mbit/s.
Serial Interface Transmit Clock Input to Ethernet Mapper: The
clock reference for TSERO, which is output on the rising edge of
the clock. TCLKE supports gapped clocking, up to a maximum
frequency of 52MHz.
TSERO
TCLKE
E2
F1
O
I
Transmit Data Enable (Input): The transmit data enable is
programmable to selectively block/enable the transmit data. The
TDEN signal must occur one clock edge prior to the affected data
bit. The active polarity of TDEN is programmable in register
LI.TSLCR. It is recommended for both T1/E1 and T3/E3
applications that use gapped clocks. The TDEN signal is provided
for interfacing to framers that do not have a gapped clock facility.
TDEN/
TBSYNC
D5
IO
Transmit Byte Sync (Output): This output can be used by an
external Serial to Parallel to convert TSERO stream to byte wide
data. This output indicates the last bit of the byte data sent serially
on TSERO. This signal is only active in the X.86 Mode.
T1/E1/J1 RECEIVE FRAMER INTERFACE
Receive Serial Data for T1/E1/J1 Transceiver: Received NRZ
serial data. Updated on rising edges of RCLKO when the receive-
side elastic store is disabled. Updated on the rising edges of
RSYSCLK when the receive-side elastic store is enabled.
Receive Clock Output from the T1/E1/J1 Framer: 1.544MHz (T1)
RSERO
RCLKO
H2
G3
O
O
O
or 2.048MHz (E1) clock that is used to clock data through the
receive-side framer. Normally connected to the RCLKI input.
Receive Channel Block for the T1/E1/J1 Transceiver: A user-
programmable output that can be forced high or low during any of
the 24 T1 or 32 E1 channels. Synchronous with RCLKO when the
receive-side elastic store is disabled. Synchronous with RSYSCLK
when the receive-side elastic store is enabled. Also useful for
locating individual channels in drop-and-insert applications, for
external per-channel loopback, and for per-channel conditioning.
See the Channel Blocking Registers section.
Receive Channel Clock for the T1/E1/J1 Transceiver: A 192kHz
(T1) or 256kHz (E1) clock that pulses high during the LSB of each
channel can also be programmed to output a gated receive-bit
clock for fractional T1/E1 applications. Synchronous with RCLKO
when the receive-side elastic store is disabled. Synchronous with
RSYSCLK when the receive-side elastic store is enabled. Useful
for parallel-to-serial conversion of channel data.
RCHBLK
RCHCLK
A1
G2
O
32 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
Receive Sync for the T1/E1/J1 Transceiver: An extracted pulse,
one RCLKO wide, is output at this pin, which identifies either frame
(TR.IOCR1.5 = 0) or multiframe (TR.IOCR1.5 = 1) boundaries. If
set to output-frame boundaries then via TR.IOCR1.6, RSYNC can
also be set to output double-wide pulses on signaling frames in T1
mode. If the receive-side elastic store is enabled, then this pin can
be enabled to be an input via TR.IOCR1.4 at which a frame or
multiframe boundary pulse is applied.
RSYNC
G4
I/O
Receive System Clock for the Transceiver: 1.544MHz,
2.048MHz, 4.096MHz, or 8.192MHz clock. Only used when the
receive-side elastic-store function is enabled. Should be tied low in
applications that do not use the receive-side elastic store.
Receive Frame Sync (Pre Receive Elastic Store) for T1/E1/J1
Transceiver: An extracted 8kHz pulse, one RCLKO wide, is output
at this pin, which identifies frame boundaries.
Receive Multiframe Sync for the T1/E1/J1 Transceiver: An
extracted pulse, one RCLKO wide (elastic store disabled) or one
RSYSCLK wide (elastic store enabled), is output at this pin, which
identifies multiframe boundaries.
RSYSCLK
RFSYNC
RMSYNC
F4
A3
U3
I
O
O
Receive Signaling Output: Outputs signaling bits in a PCM
format. Updated on rising edges of RCLKO when the receive-side
elastic store is disabled. Updated on the rising edges of RSYSCLK
when the receive-side elastic store is enabled.
RSIG
L3
O
33 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
ETHERNET MAPPER RECEIVE SERIAL INTERFACE
Receive Serial Data Input to Ethernet Mapper: Receive Serial
RSERI
RCLKI
H1
F2
I
I
data arrives on the rising edge of RCLKI. Normally connected to
RSERO.
Serial Interface Receive Clock Input to the Ethernet Mapper:
Reference clock for receive serial data on RSERI. Gapped clocking
is supported, up to the maximum RCLKI frequency of 52 MHz.
Receive Data Enable for the Ethernet Mapper: The receive data
enable is programmable to block the receive data. The RDEN must
be coincident with the RSERI data bit to be blocked or enabled.
It is recommended for both T1/E1 and T3/E3 applications that use
gapped clocks. The RDEN signal is provided for interfacing to
framers that do not have a gapped clock facility.
RDEN/
RBSYNC
P2
I
Receive Byte Synchronization Input: Provides byte
synchronization input to X.86 decoder. This signal will go high at
the last bit of the byte as it arrives. This signal can occur at
maximum rate every 8 bits. Note that a long as the R11 receives
one RBSYNC indicator. The X.86 receiver will determine the byte
boundary. Hence the R11 does not require a continuous 8 bit sync
indicator. A new sync pulse is required if the byte boundary
changes.
T1/E1/J1 FRAMER/LIU INTERIM SIGNALS
Receive Clock Input to the T1/E1/J1 Framer: Clock used to clock
data through the receive-side framer. This pin is normally
connected to RDCLKO. Can be internally connected to RDCLKO
by connecting the LIUC pin high.
Receive Clock Output from the T1/E1/J1 LIU: Buffered
recovered clock from the network. This pin is normally connected to
RDCLKI.
Receive Negative-Data Input: Sampled on the falling edge of
RDCLKI for data to be clocked through the receive-side framer.
RPOSI and RNEGI can be connected together for an NRZ
interface. Can be internally connected to RNEGO by connecting
the LIUC pin high.
Receive Negative Data Output from the T1/E1/J1 LIU: Updated
on the rising edge of RDCLKO with the bipolar data out of the line
interface. This pin is normally tied to RNEGI.
Receive Positive-Data Input to the T1/E1/J1 Framer: Sampled
on the falling edge of RDCLKI for data to be clocked through the
receive-side framer. RPOSI and RNEGI can be connected together
for an NRZ interface. Can be internally connected to RPOSO by
connecting the LIUC pin high.
RDCLKI
M4
M3
I
RDCLKO
O
I
RNEGI
RNEGO
RPOSI
L4
N2
J3
O
I
Receive Positive-Data Output from the T1/E1/J1 LIU: Updated
on the rising edge of RDCLKO with bipolar data out of the line
interface. This pin is normally connected to RPOSI.
Receive Data from the T1/E1/J1 Framer: Updated on the rising
edge of RCLKO with the data out of the receive-side framer, before
passing through the Elastic Store.
Serial Interface Transmit Clock Input for the T1/E1/J1 LIU: Line
interface transmit clock. This pin is normally tied to TCLKO. Can be
internally connected to TCLKO by connecting the LIUC pin high.
RPOSO
RDATA
TDCLKI
N3
H3
D1
O
O
I
34 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
Transmit Clock Output from the T1/E1/J1 Framer: Buffered
clock that is used to clock data through the transmit-side formatter
(either TCLKT or RDCLKI). This pin is normally tied to TDCLKI.
Transmit Negative-Data Input: Sampled on the falling edge of
TDCLKI for data to be transmitted out onto the T1 line. Can be
internally connected to TNEGO by connecting the LIUC pin high.
TPOSI and TNEGI can be connected together in NRZ applications.
Transmit Negative-Data Output: Updated on the rising edge of
TCLKO with the bipolar data out of the transmit-side formatter. This
pin is normally connected to TNEGI.
Transmit Positive-Data Input: Sampled on the falling edge of
TDCLKI for data to be transmitted out onto the T1 line. Can be
internally connected to TPOSO by connecting the LIUC pin high.
TPOSI and TNEGI can be connected together in NRZ applications.
Transmit Positive-Data Output: Updated on the rising edge of
TCLKO with the bipolar data out of the transmit-side formatter. Can
be programmed to source NRZ data by the output data format
(TR.IOCR1.0) control bit. This pin is normally connected to TPOSI.
Transmit Data: Sampled on the falling edge of TCLKT with data to
be clocked through the transmit-side formatter. This pin is normally
connected to TESO.
TDCLKO
C2
O
TNEGI
TNEGO
TPOSI
C3
D3
B3
I
O
I
TPOSO
TDATA
TESO
E1
A4
D4
O
I
Transmit Elastic Store Output: Updated on the rising edge of
TCLKT with data out of the transmit-side elastic store whether the
elastic store is enabled or not. This pin is normally connected to
TDATA.
O
35 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
HARDWARE AND STATUS PINS
Line Interface Unit Connect: When a logic low is present on this
input pin, the T1/E1/J1 Framer and LIU are not internally
connected. The line interface circuitry will be separated from the
framer/formatter circuitry and the TPOSI, TNEGI, TDCLKI, RPOSI,
RNEGI, and RDCLKI input pins will be active.
LIUC
B2
I
When a logic high is present on this input pin, the T1/E1/J1 Framer
is internally connected to the LIU. The TPOSI, TNEGI, TDCLKI,
RPOSI, RNEGI, RDCLKI input pins are deactivated. When LIUC is
connected high, the TPOSI, TNEGI, TDCLKI, RPOSI, RNEGI, and
RDCLKI pins should be tied low.
Reset for the Ethernet Mapper: An active low signal on this pin
resets the internal registers and logic of the protocol conversion
device. This pin should remain low until power, SYSCLKI, RX_CLK,
and TX_CLK are stable, then set high for normal operation. This
input requires a clean edge with a rise time of 25ns or less to
properly reset the device.
Test/Reset for the T1/E1/J1 Transceiver: A dual-function pin. A
zero-to-one transition issues a hardware reset to the transceiver
register set. A reset clears all configuration registers. Configuration
register contents are set to zero. Leaving TSTRST high will tri-state
all output and I/O pins (including the parallel control port). Set low
for normal operation. Useful in board-level testing.
Mode Control for Processor Interface:
A8
C4
I
I
RST
TSTRST
00 = Read/Write Strobe Used (Intel Mode)
01 = Data Strobe Used (Motorola Mode)
10 = Reserved. Do not use.
MODEC[0],
MODEC[1]
B19,
B20
I
11 = Reserved. Do not use.
Queue Overflow for Ethernet Mapper: This pin goes high when
the transmit or receive queue has overflowed. This pin will go low
when the high watermark is reached again.
T1/E1/J1 Receive Loss-of-Sync/Loss-of-Transmit Clock: A dual
function output that is controlled by the CCR1.0 control bit. This pin
can be programmed to either toggle high when the synchronizer is
searching for the frame and multiframe or to toggle high if the
TCLKT pin has not been toggled for 5μs.
QOVF
H18
N1
O
O
RLOS/LTC
T1/E1/J1 Receive Carrier Loss: Set high when the T1/E1/J1 line
interface detects a carrier loss.
T1/E1/J1 Receive Signaling-Freeze Output: Set high when the
signaling data is frozen by either automatic or manual intervention.
Used to alert downstream equipment of the condition.
RCL
B5
P3
O
O
RSIGF
36 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
SYSTEM CLOCKS
System Clock In for Ethernet Mapper: 100MHz System Clock
input to the DS33R11, used for internal operation. This clock is
buffered and provided at SDCLKO for the SDRAM interface. The
DS33R11 also provides a divided version output at the REF_CLKO
pin. A clock supply with ±100ppm frequency accuracy is suggested.
Master Clock Input for the T1/E1/J1 Transceiver: A (50ppm)
clock source. This clock is used internally for both clock/data
recovery and for the jitter attenuator for both T1 and E1 modes.
The clock rate can be 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz. When using the transceiver in T1-only operation a
1.544MHz (50ppm) clock source can be used.
SYSCLKI
V8
I
MCLK
H4
I
Backplane Clock from T1/E1/J1 Transceiver: A user-selectable
synthesized clock output that is referenced to the clock that is
output at the RCLKO pin.
Eight Times Clock from the T1/E1/J1 Transceiver: An 8x clock
that is locked to the recovered network clock provided from the
clock/data recovery block (if the jitter attenuator is enabled on the
receive side) or from the TDCLKI pin (if the jitter attenuator is
enabled on the transmit side).
BPCLK
8XCLK
B1
K4
O
O
Quartz Crystal Driver for the T1/E1/J1 Transceiver: A quartz
crystal of 2.048MHz (optional 1.544MHz in T1-only operation) can
be applied across MCLK and XTALD instead of a clock source at
MCLK. Leave open circuited if a clock source is applied at MCLK.
XTALD
J4
O
37 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
JTAG INTERFACE
JTAG Clock 1 for the Ethernet Mapper: This signal is used to
shift data into JTDI1 on the rising edge and out of JTDO1 on the
falling edge.
JTAG Data In 1 for the Ethernet Mapper: Test instructions and
data are clocked into this pin on the rising edge of JTCLK1. This
pin has a 10kΩ pullup resistor.
JTAG Data Out 1 for the Ethernet Mapper: Test instructions and
data are clocked out of this pin on the falling edge of JTCLK1. If not
used, this pin should be left unconnected.
JTCLK1
JTDI1
A7
C9
B7
Ipu
Ipu
Oz
JTDO1
JTAG Mode Select 1 for the Ethernet Mapper: This pin is
sampled on the rising edge of JTCLK1 and is used to place the test
access port into the various defined IEEE 1149.1 states. This pin
has a 10kΩ pullup resistor.
JTAG Reset 1 for the Ethernet Mapper: JTRST1 is used to
asynchronously reset the test access port controller. After power
up, a rising edge on JTRST1 will reset the test port and cause the
device I/O to enter the JTAG DEVICE ID mode. Pulling JTRST1
low restores normal device operation. JTRST1 is pulled HIGH
internally via a 10kΩ resistor operation. If boundary scan is not
used, this pin should be held low.
JTMS1
C8
C7
Ipu
Ipu
JTRST1
JTAG Clock 2 for the T1/E1/J1 Transceiver: This signal is used
to shift data into JTDI1 on the rising edge and out of JTDO1 on the
falling edge.
JTAG Data In 2 for the T1/E1/J1 Transceiver: Test instructions
and data are clocked into this pin on the rising edge of JTCLK2.
This pin has a 10kΩ pullup resistor.
JTAG Data Out 2 for the T1/E1/J1 Transceiver: Test instructions
and data are clocked out of this pin on the falling edge of JTCLK2.
If not used, this pin should be left unconnected.
JTCLK2
JTDI2
A6
B6
C5
Ipu
Ipu
Oz
JTDO2
JTAG Mode Select 2 for the T1/E1/J1 Transceiver: This pin is
sampled on the rising edge of JTCLK2 and is used to place the
test-access port into the various defined IEEE 1149.1 states. This
pin has a 10kΩ pullup resistor.
JTAG Reset 2 for the T1/E1/J1 Transceiver: JTRST2 is used to
asynchronously reset the test access port controller. After power-
up, JTRST2 must be toggled from low to high. This action will set
the device into the JTAG DEVICE ID mode. Normal device
operation is restored by pulling JTRST2 low. JTRST2 is pulled HIGH
internally via a 10kΩ resistor operation.
JTMS2
B9
B8
Ipu
Ipu
JTRST2
38 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
NAME
PIN
TYPE
FUNCTION
POWER SUPPLIES
RVDD
RVSS
TVDD
TVSS
K3, L1
J1, J2, K2,
L2, M2
U1
P1, R3, T3,
U2
—
—
–
Receive Analog Positive Supply: Connect to 3.3V power supply.
Receive Analog Signal Ground: Connect to the common supply
ground.
Transmit Analog Positive Supply: Connect to 3.3V power supply.
Transmit Analog Signal Ground: Connect to the common supply
ground.
–
D1–D17,
E17
N4, P4, R4,
T4
DVDD
DVSS
—
—
Digital Positive Supply: Connect to 3.3V power supply.
Digital Signal Ground: Connect to the common supply ground.
B10, B15,
C12, F3,
J18, J20,
P18, P19,
R19, R20,
V9, Y9, Y13
D20, F17,
G17, G18,
H17, J17,
K17, L17,
M17, N17,
P17, R17,
R18, T17,
T18, U17
A15, C10,
D8, D9,
VDD1.8
VDD3
I
I
VDD1.8: Connect to 1.8V power supply.
VDD3.3: Connect to 3.3V power supply.
D10, D18,
D19, E18,
H20, J19,
K20, N19,
N20, P20,
U4–U16,
U18, V20,
W8, W18,
Y1, Y7
VSS
N.C.
I
VSS: Connect to the common supply ground.
No Connection. Do not connect these pins. Leave these pins
open.
A9, C6, D6
—
39 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 7-1. 256-Ball BGA Pinout
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
REF_
CLKO
RCHBLK TCHBLK RFSYNC TDATA TSSYNC JTCLK2 JTCLK1
RST
N.C.
INT
CS
D6
D3
D0
VSS
A6
A3
A0
REF_CLK
A
B
C
D
E
F
MODEC MODEC
BPCLK
LIUC
TPOSI
TSIG
RCL
JTDI2
N.C.
JTDO1
JTRST1
CST
JTRST2
JTMS1
VSS
JTMS2
JTDI1
VSS
VDD1.8
VSS
RD/DS
D7
D4
D5
D1
D2
VDD1.8
A9
A7
A8
A4
A1
A2
[0]
[1]
TSYNC TDCLKO TNEGI TSTRST JTDO2
TDEN/
WR/RW VDD1.8
A5
MDC
MDIO
TDCLKI
TCLKT
TNEGO
TESO
N.C.
VSS
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
DVDD
VDD3
VDD3
VDD3
VDD3
VDD3
VDD3
VDD3
VSS
VSS
VSS
VDD3
TBSYNC
TXD
[3]
TXD
[2]
TPOSO TSERO
TSERI TSYSCLK
VDD1.8 RSYSCLK
TXD
[1]
TXD
[0]
TCLKE
RCLKI
TX_EN
DCE
DTES
TCHCLK RCHCLK RCLKO RSYNC
VDD3 RMIIMIIS
G
H
J
RSERI
RVSS
RTIP
RSERO RDATA
MCLK
XTALD
8XCLK
RNEGI
QOVF
TX_CLK
VSS
VSS
VDD1.8
VSS
RVSS
RVSS
RVSS
RPOSI
RVDD
RSIG
VDD1.8
RX_ERR RX_DV
K
L
RXD
[0]
RXD
[1]
RXD
[2]
RVDD
RRING
RXD RX_CRS /
[3]
RVSS RDCLKO RDCLKI
RX_CLK
VSS
M
N
P
R
T
CRS_DV
RLOS/
LTC
RNEGO RPOSO
DVSS
DVSS
DVSS
DVSS
VSS
VDD3 COL_DEt
VSS
RDEN/
RSIGF
TVSS
TTIP
VDD3
VDD3
VDD3
VDD3
VDD1.8 VDD1.8
VSS
RBSYNC
TTIP
TVSS
TVSS
VDD3
VDD3
VSS
VDD1.8 VDD1.8
SDATA
[25]
SDATA
[26]
TRING
TVDD
TRING
SDATA
[22]
SDATA
[24]
TVSS RMSYNC
VSS
VSS
VSS
VSS
VSS
VSS
SDCS
SWE
VSS
VSS
VSS
VSS
VSS
VSS
U
V
W
Y
SDATA
[13]
SDATA
[11]
SDATA
[12]
SDATA
[10]
SDATA
[6]
SDATA SDMASK
SBA
[1]
SDA
[8]
SDA
[5]
SDA
[10]
SDMASK SDMASK SDATA
[3]
SDATA
[18]
SDATA
[20]
SYSCLKI VDD1.8
VSS
[8]
[1]
[2]
[29]
SDATA
[15]
SDATA
[0]
SDATA
[14]
SDATA
[9]
SDATA
[5]
SDATA
[7]
SDA
[11]
SDA
[1]
SDA
[6]
SDA
[0]
SDA
[3]
SDATA
[31]
SDATA
[30]
SDATA
[28]
SDATA
[23]
SCAS
VSS
SRAS
VSS
SDATA
[2]
SDATA
[4]
SDATA
[1]
SDATA SDMASK
[3] [0]
SDA
[9]
SBA
[0]
SDA
[7]
SDA
[4]
SDA
[2]
SDATA
[16]
SDATA
[17]
SDATA
[27]
SDATA
[19]
SDATA
[21]
VSS
VSS
SDCLKO VDD1.8
VDD1.8
40 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
8 FUNCTIONAL DESCRIPTION
The DS33R11 provides interconnection and mapping functionality between Ethernet packet LANs and T1/E1/J1
WAN Time-Division Multiplexed (TDM) systems. The device is composed of a 10/100 Ethernet MAC, packet
arbiter, committed information rate controller (CIR), HDLC/X.86 (LAPS) mapper, SDRAM interface, control ports,
bit error-rate tester (BERT), and integrated T1/E1/J1 transceiver. The packet interface consists of a MII/RMII
Ethernet PHY interface. The Ethernet interface can be configured for 10Mbit/s or 100Mbit/s service. The DS33R11
encapsulates Ethernet traffic with HDLC or X.86 (LAPS) encoding to be transmitted over a T1, E1, or J1 line. The
T1/E1/J1 interface also receives encapsulated Ethernet packets and transmits the extracted packets over the
Ethernet ports. Access is provided to the signals between the serial port and the integrated T1/E1/J1 transceiver.
The Ethernet packet interface supports MII and RMII interfaces, allowing the DSZ33R11 to connect to
commercially available Ethernet PHY and MAC devices. The Ethernet interface can be configured for 10Mbit/s or
100Mbit/s service, in DTE and DCE configurations. The DS33R11 MAC interface rejects frames with bad FCS and
short frames (less than 64 bytes).
Ethernet frames are queued and stored in external 32-bit SDRAM. The DS33R11 SDRAM controller enables
connection to a 128Mb SDRAM without external glue logic, at clock frequencies up to 100MHz. The SDRAM is
used for both the transmit and receive data queues. The receive queue stores data to be sent from the packet
interface to the WAN serial interface. The transmit queue stores data to be sent from the WAN serial interface to
the Ethernet LAN packet interface. The external SDRAM can accommodate up to 8192 frames with a maximum
frame size of 2016 bytes. The sizing of the queues can be adjusted by software. The user can also program high
and low watermarks for each queue that can be used for automatic or manual flow control. The packet data stored
in the SDRAM is encapsulated in HDLC or X.86 (LAPS) to be transmitted over the WAN interface. The device also
provides the capability for bit and packet scrambling.
The WAN interface also receives encapsulated Ethernet packets and transmits the extracted packets over the
Ethernet port. The WAN serial port can operate with a gapped clock, and is designed to be connected to the
integrated T1/E1/J1 transceiver for transmission.
The DS33R11 can be configured through an 8-bit microprocessor interface port. Diagnostic capabilities include
loopbacks, PRBS pattern generation/detection, and 16-bit loop-up/loop-down code generation and detection. The
DS33R11 provides two on-board clock dividers for the system-clock input and reference-clock input for the 802.3
interfaces, further reducing the need for ancillary devices.
The integrated transceiver is a software-selectable T1, E1, or J1 single-chip transceiver (SCT) for short-haul and
long-haul applications. The transceiver is composed of an LIU, framer, HDLC controllers, and a TDM backplane
interface, and is controlled by the 8-bit parallel port. The transceiver is software compatible with the DS2155 and
DS2156.
The LIU is composed of transmit and receive interfaces and a jitter attenuator. The transmit interface is responsible
for generating the necessary waveshapes for driving the network and providing the correct source impedance
depending on the type of media used. T1 waveform generation includes DSX-1 line build-outs as well as CSU line
build-outs of -7.5dB, -15dB, and -22.5dB. E1 waveform generation includes G.703 waveshapes for both 75Ω coax
and 120Ω twisted cables. The receive interface provides network termination and recovers clock and data from the
network. The receive sensitivity adjusts automatically to the incoming signal and can be programmed for 0 to 43dB
or 0 to 12dB for E1 applications and 0 to 30dB or 0 to 36dB for T1 applications. The jitter attenuator removes
phase jitter from the transmitted or received signal. The crystal-less jitter attenuator requires only a 2.048MHz
MCLK for both E1 and T1 applications (with the option of using a 1.544MHz MCLK in T1 applications) and can be
placed in either transmit or receive data paths. An additional feature of the LIU is a CMI coder/decoder for
interfacing to optical networks.
On the transmit side, clock, data, and frame-sync signals are provided to the framer by the backplane interface
section. The framer inserts the appropriate synchronization framing patterns, alarm information, calculates and
inserts the CRC codes, and provides the B8ZS/HDB3 (zero code suppression) and AMI line coding. The receive-
side framer decodes AMI, B8ZS, and HDB3 line coding, synchronizes to the data stream, reports alarm
information, counts framing/coding/CRC errors, and provides clock/data and frame-sync signals to the backplane
interface section.
41 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Both the transmit and receive path of the integrated T1/E1/J1 transceiver also have two HDLC controllers. The
HDLC controllers transmit and receive data through the framer block. The HDLC controllers can be assigned to
any time slot, group of time slots, portion of a time slot or to FDL (T1) or Sa bits (E1). Each controller has 128-byte
FIFOs, thus reducing the amount of processor overhead required to manage the flow of data. In addition, built-in
support for reducing the processor time is required in SS7 applications.
The backplane interface provides a versatile method of sending and receiving data from the host system. Elastic
stores provide a method for interfacing to asynchronous systems, converting from a T1/E1 network to a 2.048MHz,
4.096MHz, 8.192MHz, or N x 64kHz system backplane. The elastic stores also manage slip conditions
(asynchronous interface).
8.1 Processor Interface
Microprocessor control of the DS33R11 is accomplished through the interface pins of the microprocessor port. The
8-bit parallel data bus can be configured for Intel or Motorola modes of operation with the two MODEC[1:0] pins.
MODEC[1:0] = 01, bus timing is in Motorola mode, as shown in Figure 13-11 and Figure 13-12. The address space
is mapped through the use of 10 address lines, A0-A9. Multiplexed Mode is not supported on the processor
The Chip Select (CS) pin must be brought to a logic low level to gain read and write access to the microprocessor
port. With Intel timing selected, the Read (RD) and Write (WR) pins are used to indicate read and write operations
and latch data through the interface. With Motorola timing selected, the Read-Write (RW) pin is used to indicate
read and write operations while the Data Strobe (DS) pin is used to latch data through the interface.
The interrupt output pin (INT) is an open-drain output that will assert a logic-low level upon a number of software
maskable interrupt conditions. This pin is normally connected to the microprocessor interrupt input. The register
8.1.1 Read-Write/Data Strobe Modes
The processor interface can operate in either read-write strobe mode or data strobe mode. When MODEC[1:0] =
00 the read-write strobe mode is enabled and a negative pulse on RD performs a read cycle, and a negative pulse
on WR performs a write cycle. When MODEC[1:0] pins = 01 the data strobe mode is enabled and a negative pulse
on DS when RW is high performs a read cycle, and a negative pulse on DS when RW is low performs a write cycle.
The read-write strobe mode is commonly called the “Intel” mode, and the data strobe mode is commonly called the
“Motorola” mode.
8.1.2 Clear on Read
The latched status registers will clear on a read access. It is important to note that in a multi-task software
environment, the user should handle all status conditions of each register at the same time to avoid inadvertently
clearing status conditions. The latched status register bits are carefully designed so that an event occurrence
cannot collide with a user read access.
8.1.3 Interrupt and Pin Modes
The interrupt (INT) pin is configurable to drive high or float when not active. The INTM bit controls the pin
configuration, when it is set the INT pin will drive high when not active. After reset, the INT pin is in high-impedance
mode until an interrupt source is active and enabled to drive the interrupt pin.
42 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9 ETHERNET MAPPER
9.1 Ethernet Mapper Clocks
The DS33R11 clocks sources and functions are as follows:
•
Serial Transmit Data (TCLKE) and Serial Receive Data (RCLKI) clock inputs are used to transfer data from
the serial interface. These clocks can be continuous or gapped.
•
System Clock (SYSCLKI) input. Used for internal operation. This clock input cannot be a gapped clock. A
clock supply with ±100ppm frequency accuracy is suggested. A buffered version of this clock is provided
on the SDCLKO pin for the operation of the SDRAM. A divided and buffered version of this clock is
provided on REF_CLKO for the RMII/MII interface.
•
•
Packet Interface Reference clock (REF_CLK) input that can be 25MHz or 50MHz. This clock is used as
the timing reference for the RMII/MII interface.
The Transmit and Receive clocks for the MII Interface (TX_CLK and RX_CLK). In DTE mode, these are
input pins and accept clocks provided by an Ethernet PHY. In the DCE mode, these are output pins and
will output an internally generated clock to the Ethernet PHY. The output clocks are generated by internal
division of REF_CLK. In RMII mode, only the REF_CLK input is used.
•
•
REF_CLKO is an output clock that is generated by dividing the 100MHz System clock (SYSCLKI) by 2 or
4.
A Management Data Clock (MDC) output is derived from SYSCLKI and is used for information transfer
between the internal Ethernet MAC and external PHY. The MDC clock frequency is 1.67MHz.
Clocking of the integrated T1/E1/J1 tansceiver is discussed in Section 10.1. The following table provides the
different clocking options for the Ethernet interface.
Table 9-1. Clocking Options for the Ethernet Interface
RMIIMIIS
PIN
REF_CLKO REF_CLK
MDC
OUTPUT
SPEED
10 Mbps
10 Mbps
100 Mbps
10 Mbps
100 Mbps
DCE/ DTE
DTE
DCE
DCE
—
RX_CLK
TX_CLK
OUTPUT
INPUT
25MHz
±100ppm
25MHz
±100ppm
25MHz
±100ppm
50MHz
±100ppm
50MHz
±100ppm
Input from
PHY
Input from
PHY
0 (MII)
0 (MII)
25MHz
1.67MHz
1.67MHz
1.67MHz
1.67MHz
1.67MHz
2.5MHz
(Output)
25MHz
(Output)
Not
Applicable
Not
Applicable
2.5MHz
(Output)
25MHz
(Output)
Not
Applicable
Not
Applicable
25MHz
25MHz
50MHz
50MHz
0 (MII)
1 (RMII)
1 (RMII)
—
43 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-1. Clocking for the DS33R11
μP Port
CLAD
CLAD
SYSCLKI
REF_CLKO
RX_CLK
TTIP
MUX
TRING
HDLC
REF_CLK
BERT
ARBITER
HDLC
RTIP
TX_CLK
MDC
MUX
RRING
JTAG2
JTAG1
SDRAM PORT
NOTE THAT THE CLOCKING OPTIONS OF THE INTEGRATED T1/E1/J1 TANSCEIVER ARE DISCUSSED IN SECTION 10.1.
44 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.1.1 Ethernet Interface Clock Modes
The Ethernet PHY interface has several different clocking requirements, depending on the mode of operation.
Table 9-1 outlines the possible clocking modes for the Ethernet Interface. The buffered REF_CLKO output is
generated by division of the 100MHz system clock input by the user on SYSCLKI. The frequency of the
REF_CLKO pin is automatically determined by the DS33R11 based on the state of the RMIIMIIS pin. The
REF_CLKO function can be turned off with the GL.CR1.RFOO bit. Note that in DCE and RMII operating modes,
the REF_CLKO signal should not be used to provide an input to REF_CLK, due to the reset requirements in these
operating modes.
In RMII mode, receive and transmit timing is always synchronous to a 50 MHz clock input on the REF_CLK pin.
The source of REF_CLK is expected to be the external PHY. The user has the option of using the 50MHz
REF_CLKO output as the timing source for the PHY. More information on RMII mode can be found in
While using MII mode with DTE operation, the MII clocks (RX_CLK and TX_CLK) are inputs that are expected to
be provided by the external PHY. While using MII mode with DCE operation, the MII clocks (TX_CLK and
RX_CLK) are output by the DS33R11, and are derived from the 25MHz REF_CLK input. More information on MII
9.1.2 Serial Interface Clock Modes
The serial interface timing is determined by the line clocks. Both the transmit and receive clocks (TCLKE and
RCLKI) are inputs, and can be gapped.
45 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.2 Resets and Low Power Modes
The external RST pin and the global reset bit in GL.CR1 create an internal global reset signal. The global reset
signal resets the status and control registers on the chip (except the GL.CR1.RST bit) to their default values and
resets all the other flops to their reset values. The processor bus output signals are also placed in high-impedance
mode when the RST pin is active (low). The global reset bit (GL.CR1.RST) stays set after a one is written to it, but
is reset to zero when the external RST pin is active or when a zero is written to it. Allow 5ms after initiating a reset
condition for the reset operation to complete.
The Serial Interface reset bit in LI.RSTPD resets all the status and control registers on the serial interface to their
default values, except for the LI.RSTPD.RST bit. The serial interface includes the HDLC encoder/decoder, X86
encoder and decoder and the corresponding serial port. The serial interface reset bit (LI.RSTPD.RST) stays set
after a one is written to it, but is reset to zero when the global reset signal is active or when a zero is written to it.
Table 9-2. Reset Functions
RESET FUNCTION
Hardware Device Reset
Hardware JTAG Reset
Global Software Reset
Serial Interface Reset
Queue Pointer Reset
LOCATION
RST Pin
COMMENTS
Transition from a logic 0 to a logic 1 resets the device.
Resets the JTAG test port.
JTRST Pin
Writing to this bit resets the device.
Writing to this bit resets the Serial Interface.
Writing to this bit resets the Queue Pointers.
There are several features in the DS33R11 to reduce power consumption. The reset bit in the LI.RSTPD register
minimizes power usage in the Serial Interface. Additionally, the RST pin or GL.CR1.RST bit may be held in reset
indefinitely to keep the device in a low-power mode. Note that exiting a reset condition requires re-initialization and
configuration. For the lowest possible standby current, clocks may be externally gated.
The T1/E1/J1 transceiver contains an on-chip power-up reset function that automatically clears the writeable
register space immediately after power is supplied to the transceiver. The user can issue a chip reset at any time.
Issuing a reset disrupts traffic flowing through the transceiver until the device is reprogrammed. The reset can be
issued through hardware using the TSTRST pin or through software using the SFTRST function in the master
mode register. The LIRST (TR.LIC2.6) should be toggled from 0 to 1 to reset the line interface circuitry. (It takes
the transceiver about 40ms to recover from the LIRST bit being toggled.) Finally, after the TSYSCLK and
RSYSCLK inputs are stable, the receive and transmit elastic stores should be reset (this step can be skipped if the
elastic stores are disabled).
46 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.3 Initialization and Configuration
EXAMPLE DEVICE INITIALIZATION SEQUENCE:
STEP 1: Apply 3.3V supplies, then apply 1.8V supplies.
STEP 2: Reset the integrated Ethernet Mapper by pulling the RST pin low or by using the software reset bits
STEP 3: Reset the integrated T1/E1/J1 Transceiver through hardware using the TSTRST pin or through software
using the SFTRST function in the master mode register.
STEP 4: The LIRST (TR.LIC2.6) should be toggled from 0 to 1 to reset the line interface circuitry. Allow 40ms for
the reset recovery.
STEP 6: Check the T1/E1/J1 Transceiver Device ID in the TR.IDR register.
STEP 7: Configure the system clocks. Allow the clock system to properly adjust.
STEP 8: Initialize the entire remainder of the register space with 00h (or otherwise if specifically noted in the
register’s definition), including the reserved bits and reserved register locations.
STEP 9: Write FFFFFFFFh to the MAC indirect addresses 010Ch through 010Fh.
STEP 10: Setup connection in the GL.CON1 register.
STEP 11: Configure the Serial Port register space as needed.
STEP 12: Configure the Ethernet Port register space as needed.
STEP 13: Configure the Ethernet MAC indirect registers as needed.
STEP 14: Configure the T1/E1/J1 Framer as needed.
STEP 15: Configure the T1/E1/J1 LIU as needed.
STEP 16: Configure the external Ethernet PHY through the MDIO interface.
STEP 17: Clear all counters and latched status bits.
STEP 18: Set the queue size in the Arbiter and reset the queue pointers for the Ethernet and serial interfaces.
STEP 19: After the TSYSCLK and RSYSCLK inputs to the T1/E1/J1 transceiver are stable, the receive and
transmit elastic stores should be reset (this step can be skipped if the elastic stores are disabled).
STEP 20: Enable Interrupts as needed.
STEP 21: Begin handling interrupts and latched status events.
9.4 Global Resources
In order to maintain software compatibility with the multiport devices in the product family, a set of global registers
are located at 0F0h-0FFh. The global registers include Global resets, global interrupt status, interrupt masking,
clock configuration, and the Device ID registers. See the Global Register Definitions in Table 11-2.
9.5 Per-Port Resources
Multiport devices in this product family share a common set of global registers, BERT, and arbiter. All other
resources are per-port.
47 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.6 Device Interrupts
Figure 9-2 diagrams the flow of interrupt conditions from their source status bits through the multiple levels of
information registers and mask bits to the interrupt pin. When an interrupt occurs, the host can read the Global
Latched Status registers GL.LIS, GL.SIS, GL.BIS, and GL.TRQIS to initially determine the source of the interrupt.
The host can then read the LI.TQCTLS, LI.TPPSRL, LI.RPPSRL, LI.RX86S, SU.QCRLS, or BSRL registers to
further identify the source of the interrupt(s). In order to maintain software compatibility with the multiport devices in
the product family, the global interrupt status and interrupt enable registers have been preserved, but do not need
to be used. If GL.TRQIS is determined to be the interrupt source, the host will then read the LI.TPPSRL and
LI.RPPSRL registers for the cause of the interrupt. If GL.LIS is determined to be the interrupt source, the host will
then read the LI.TQCTLS, LI.TPPSRL, LI.RPPSRL, and LI.RX86S registers for the source of the interrupt. If
GL.SIS is the source, the host will then read the SU.QCRLS register for the source of the interrupt. If GL.BIS is the
source, the host will then read the BSRL register for the source of the interrupt. All Global Interrupt Status Register
bits are real-time bits that will clear once the appropriate interrupt has been serviced and cleared, as long as no
additional, enabled interrupt conditions are present in the associated status register. All Latched Status bits must
be cleared by the host writing a “1” to the bit location of the interrupt condition that has been serviced. In order for
individual status conditions to transmit their status to the next level of interrupt logic, they must be enabled by
placing a “1” in the associated bit location of the correct Interrupt Enable Register. The Interrupt enable registers
are LI.TPPSRIE, LI.RPPSRIE, LI.RX86LSIE, BSRIE, SU.QRIE, GL.LIE, GL.SIE, GL.BIE, and GL.TRQIE. Latched
Status bits that have been enabled via Interrupt Enable registers are allowed to pass their interrupt conditions to
the Global Interrupt Status Registers. The Interrupt enable registers allow individual Latched Status conditions to
generate an interrupt, but when set to zero, they do not prevent the Latched Status bits from being set. Therefore,
when servicing interrupts, the user should AND the Latched Status with the associated Interrupt Enable Register in
order to exclude bits for which the user wished to prevent interrupt service. This architecture allows the application
host to periodically poll the latched status bits for noninterrupt conditions, while using only one set of registers.
Note the bit-orders of SU.QRIE and SU.QCRLS are different.
Note that the inactive state of the interrupt output pin is configurable. The INTM bit in GL.CR1 controls the inactive
state of the interrupt pin, allowing selection of a pull-up resistor or active driver.
The interrupt structure is designed to efficiently guide the user to the source of an enabled interrupt source. The
latched status bits for the interrupting entity must be read to clear the interrupt. Also reading the latched status bit
will reset all bits in that register. During a reset condition, interrupts cannot be generated. The interrupts from any
source can be blocked at a global level by the placing a zero in the global interrupt enable registers (GL.LIE,
GL.SIE, GL.BIE, and GL.TRQIE). Reading the Latched Status bit for all interrupt generating events will clear the
interrupt status bit and Interrupt signal will be de-asserted.
Note that the integrated T1/E1/J1 transceiver also generates interrupts, as discussed in Section 10.3.
48 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-2. Device Interrupt Information Flow Diagram
Receive FCS Errored Packet
Receive Aborted Packet
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
Drawing Legend:
Receive Invalid Packet Detected
Receive Small Packet Detected
Receive Large Packet Detected
Receive FCS Errored Packet Count
Receive Aborted Packet Count
Receive Size Violation Packet Count
Interrupt Status
Register Name
Registers
Interrupt
Enable
<Reserved>
<Reserved>
Registers
<Reserved>
<Reserved>
<Reserved>
<Reserved>
<Reserved>
Transmit Errored Packet Insertion Finished
<Reserved>
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
<Reserved>
<Reserved>
<Reserved>
SAPI High is not equal to LI.TRX86SAPIH
SAPI Low is not equal to LI.TRX86SAPIL
Control is not equal to LI.TRX8C
Address is not equal to LI.TRX86A
<Reserved>
<Reserved>
<Reserved>
<Reserved>
Transmit Queue FIFO Overflowed
Transmit Queue Overflow
Transmit Queue for Connection Exceeded Low Threshold
Transmit Queue for Connection Exceeded High
Threshold
0
<Reserved>
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
<Reserved>
<Reserved>
<Reserved>
Receive Queue FIFO Overflowed
Receive Queue Overflow
Receive Queue for Connection Exceeded Low Threshold
Receive Queue for Connection Exceeded High Threshold
<Reserved>
<Reserved>
<Reserved>
<Reserved>
Performance Monitor Update
Bit Error Detected
Bit Error Count
Out Of Synchronization
49 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.7 Interrupt Information Registers
The interrupt information registers provide an indication of which status registers (SR1 through SR9) are
generating an interrupt. When an interrupt occurs, the host can read TR.IIR1 and TR.IIR2 to quickly identify which
of the nine status registers are causing the interrupt.
9.8 Status Registers
When a particular event or condition has occurred (or is still occurring in the case of conditions), the appropriate bit
in a status register is set to a 1. All of the status registers operate in a latched fashion. This means that if an event
or condition occurs a bit is set to a 1. It remains set until the user reads that bit. An event bit is cleared when it is
read and it is not set again until the event has occurred again. Condition bits such as RBL, RLOS, etc., remain set
if the alarm is still present.
The user always proceeds a read of any of the status registers with a write. The byte written to the register informs
the device which bits the user wishes to read and have cleared. The user writes a byte to one of these registers,
with a 1 in the bit positions the user wishes to read and a 0 in the bit positions the user does not wish to obtain the
latest information on. When a 1 is written to a bit location, the read register is updated with the latest information.
When a 0 is written to a bit position, the read register is not updated and the previous value is held. A write to the
status registers is immediately followed by a read of the same register. This write-read scheme allows an external
microcontroller or microprocessor to individually poll certain bits without disturbing the other bits in the register.
This operation is key in controlling the device with higher order languages.
Status register bits are divided into two groups, condition bits and event bits. Condition bits are typically network
conditions such as loss-of-sync or all-ones detect. Event bits are typically markers such as the one-second timer,
elastic store slip, etc. Each status register bit is labeled as a condition or event bit. Some of the status registers
have bits for both the detection of a condition and the clearance of the condition. For example, TR.SR2 has a bit
that is set when the device goes into a loss-of-sync state (TR.SR2.0, a condition bit) and a bit that is set
(TR.SR2.4, an event bit) when the loss-of-sync condition clears (goes in sync). Some of the status register bits
(condition bits) do not have a separate bit for the “condition clear” event but rather the status bit can produce
interrupts on both edges, setting and clearing. These bits are marked as double interrupt bits. An interrupt is
produced when the condition occurs and when it clears.
9.9 Information Registers
Information registers operate the same as status registers except they cannot cause interrupts. They are all
latched except for TR.INFO7 and some of the bits in TR.INFO5 and TR.INFO6. TR.INFO7 register is a read-only
register. It reports the status of the E1 synchronizer in real time. TR.INFO7 and some of the bits in TR.INFO6 and
TR.INFO5 are not latched and it is not necessary to precede a read of these bits with a write.
9.10 Serial Interface
The Serial (WAN) interface is intended to be connected to the integrated T1/E1/J1 Transceiver. However, the
interface supports time-division multiplexed, serial data input and output up to 52 Mbit/s. The Serial interface
receives and transmits encapsulated Ethernet packets. The Serial Interface block consists of the physical serial
port and HDLC / X.86 engine. The physical interface consists of a Transmit Data, Transmit Clock, Transmit Enable,
Receive Data, Receive Clock, and Receive Enable. The WAN serial port can operate with a gapped clock, and can
be connected to a framer, electrical LIU, optical transceiver, or T/E-Carrier transceiver for transmission to the
WAN.
50 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.11 Connections and Queues
The multi-port devices in this product family provide bidirectional cross-connections between the multiple Ethernet
ports and Serial ports when operating in software mode. A single connection is preserved in this single-port device
to provide software compatibility with multi-port devices. The connection will have an associated transmit and
receive queue. Note that the terms “Transmit Queue” and “Receive Queue” are with respect to the Ethernet
Interface. The Receive queue is for data arriving from Ethernet interface to be transmitted to the WAN interface.
The Transmit queue is for data arriving from the WAN to be transmitted to the Ethernet interface. Hence the
transmit and receive direction terminology is the same as is used for the Ethernet MAC port.
The user can define the connection and the size of the transmit and receive queues. The size is adjustable in units
of 32 (by 2048 byte) packets. The external SDRAM can hold up to 8192 packets of data. The user must ensure
that all the connection queues do no exceed this limit. The user also must ensure that the transmit and receive
queues do not overlap each other. Unidirectional connections are not supported.
When the user changes the queue sizes, the connection must be torn down and re-established. When a
connection is disconnected all transmit and receive queues associated with the connection are flushed and a “1’ is
sourced towards the Serial transmit and the HDLC receiver. The clocks to the HDLC are sourced a “0”.
The user can also program high and low watermarks. If the queue size grows past the High watermark, an
interrupt is generated if enabled. The registers of relevance are described in Table 9-3. The AR.TQSC1 size
provides the size of the transmit queue for the connection. The high watermark will set a latched status bit. The
latched status bit will clear when the register is read. The status bit is indicated by LI.TQCTLS.TQHTS. Interrupts
can be enabled on the latched bit events by LI.TQTIE. A latched status bit (LI.TQCTLS.TQLTS) is also set when
the queue crosses a low watermark.
The Receive Queue functions in a similar manner. Note that the user must ensure that sizes and watermarks are
set in accordance with the configuration speed of the Ethernet and Serial interfaces. The DS33R11 does not
provide error indication if the user creates a connection and queue that overwrites data for another connection
queue. The user must take care in setting the queue sizes and watermarks. The registers of relevance are
51 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
It is recommended that the user reset the queue pointers for the connection after disconnection. The pointers must
be reset before a connection is made. If this disconnect/connect procedure is not followed, incorrect data may be
transmitted. The proper procedure for setting up a connection follows:
•
•
•
•
•
If a connection is disconnected, reset the queue pointers after the disconnection.
Table 9-3. Registers Related to Connections and Queues
REGISTER
FUNCTION
Enables connection between the Ethernet Interface and the Serial Interface. Note that once
connection is set up, then the queues and thresholds can be setup for that connection.
Size for the Transmit Queue in Number of 32—2K packets.
Size for the Receive Queue in Number of 32—2K packets.
Interrupt enable for items related to the connections at the global level
Interrupt enable status for items related to the connections at the global level
Enables for the Transmit queue crossing high and low thresholds
Latched status bits for connection high and low thresholds for the transmit queue.
Enables for the receive queue crossing high and low thresholds
Latched status bits for receive queue high and low thresholds.
Resets the connection pointer.
9.12 Arbiter
The Arbiter manages the transport between the Ethernet port and the Serial port. It is responsible for queuing and
dequeuing packets to a single external SDRAM. The arbiter handles requests from the HDLC and MAC to transfer
data to and from the SDRAM.
52 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.13 Flow Control
Flow control may be required to ensure that data queues do not overflow and packets are not lost. The DS33R11
allows for optional flow control based on the queue high watermark or through host processor intervention. There
are 2 basic mechanisms that are used for flow control:
•
In half duplex mode, a jam sequence is sent that causes collisions at the far end. The collisions cause the
transmitting node to reduce the rate of transmission.
•
In full duplex mode, flow control is initiated by the receiving node sending a pause frame. The pause frame
has a timer parameter that determines the pause timeout to be used by the transmitting node.
Note that the terms “transmit queue” and “receive queue” are with respect to the Ethernet Interface. The Receive
Queue is the queue for the data that arrives on the MII/RMII interface, is processed by the MAC and stored in the
SDRAM. Transmit queue is for data that arrives from the Serial port, is processed by the HDLC and stored in the
SDRAM to be sent to the MAC transmitter.
The following flow control options are possible:
•
•
Automatic flow control can be enabled in software mode with the SU.GCR.ATFLOW bit. Note that the user
does not have control over SU.MACFCR.FCE and FCB bits if ATFLOW is set. The mechanism of sending
pause or jam is dependent only on the receive queue high threshold.
Manual flow control can be performed through software when SU.GCR.ATFLOW=0. The host processor
must monitor the receive queues and generate pause frames (full duplex) and/or jam bytes through the
SU.MACFCR.FCB, SU.GCR.JAME, and SU.MACFCR.FCE bits.
Note that in order to use flow control, the receive queue size (in AR.RQSC1) must be 02h or greater. The receive
queue high threshold (in SU.RQHT) must be set to 01h or greater, but must be less than the queue size. If the high
threshold is set to the same value as the queue size, automatic flow control will not be effective. The high threshold
must always be set to less than the corresponding queue size.
The following table provides all the options on flow control mechanism for DS33R11.
Table 9-4. Options for Flow Control
TYPE
MODE
Half Duplex;
Automatic Flow
Control
Full Duplex;
Automatic Flow
Control
Half Duplex; Manual
Flow Control
Full Duplex; Manual
Configuration
Flow Control
0
1
0
1
ATFLOW Bit
JAME Bit
Controlled
Automatically
Controlled By User
N/A
N/A
FCB Bit
(Pause)
Controlled
Automatically
N/A
N/A
Controlled by User
Controlled By User
Controlled
Automatically
Controlled
Automatically
Controlled By User
N/A
FCE Bit
N/A
Programmed by User Programmed by User
Pause Timer
53 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.13.1 Full Duplex Flow Control
Automatic flow control is enabled by default. The host processor can disable this functionality with
low threshold can be used as indication that the network congestion is clearing up. The value of SU.RQLT does
not affect the flow control. When the connection queue high threshold is exceeded the DS33R11 will send a pause
frame with the timer value programmed by the user. See Table 9-6 for more information. It is recommended that 80
slots (80 by 64 bytes or 5120 bytes) be used as the standard timer value.
The pause frame causes the distant transmitter to “pause for a time” before starting transmission again. The pause
command has a multicast address 01-80-62-00-00-01. The high and low thresholds for the receive queue are
configurable by the user but it is recommended that the high threshold be set approximately 96 packets from the
maximum size of the queue and the low threshold 96 packets lower than the high threshold. The DS33R11 will
send a pause frame as the queue has crossed the high threshold and a frame is received. Pause is sent every
time a frame is received in the “high threshold state”. Pause control will only take care of temporary congestion.
Pause control does not take care of systems where the traffic throughput is too high for the queue sizes selected. If
the flow control is not effective the receive queue will eventually overflow. This is indicated by
SU.QCRLS.RQOVFL latched bit. If the receive queue is overflowed any new frames will not be received.
The user has the option of not enabling automatic flow control. In this case the thresholds and corresponding
interrupt mechanism to send pause frame by writing to flow control busy bit in the MAC flow control registers
SU.MACFCR.FCB, SU.GCR.JAME, and SU.MACFCR. This allows the user to set not only the watermarks but also
to decide when to send a pause frame or not based on watermark crossings.
On the receive side the user has control over whether to respond to the pause frame sent by the distant end (PCF
bit). Note that if automatic flow control is enabled the user cannot modify the FCE bit in the MAC flow control
register. On the Transmit queue the user has the option of setting high and low thresholds and corresponding
interrupts. There is no automatic flow control mechanism for data received from the Serial side waiting for
transmission over the Ethernet interface during times of heavy Ethernet congestion.
54 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-3. Flow Control Using Pause Control Frame
8
Receive Queue Low
Water
Rx
Data
Receive Queue High
Water Mark
Initiate Flow control
Receive Queue
Growth
9.13.2 Half Duplex Flow Control
Half duplex flow control uses a jamming sequence to exert backpressure on the transmitting node. The receiving
node jams the first 4 bytes of a packet that are received from the MAC in order to cause collisions at the distant
end. In both 100Mbit/s and 10Mbit/s MII/RMII modes, 4 bytes are jammed upon reception of a new frame. Note
that the jamming mechanism does not jam the current frame that is being received during the watermark crossing,
but will wait to jam the next frame after the SU.RQHT bit is set. If the queue remains above the high threshold,
received frames will continue to be jammed. This jam sequence is stopped when the queue falls below the high
threshold.
9.13.3 Host-Managed Flow Control
Although automatic flow control is recommended, flow control by the host processor is also possible. By utilizing
the high watermark interrupts, the host processor can manually issue pause frames or jam incoming packets to
exert backpressure on the transmitting node. Pause frames can be initiated with SU.MACFCR.FCB bit. Jam
sequences can be initiated be setting SU.GCR.JAME. The host can detect pause frames by monitoring
SU.RFSB3.UF and SU.RFSB3.CF. Jammed frames will be indistinguishable from packet collisions.
55 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.14 Ethernet Interface Port
The Ethernet port interface allows for direct connection to an Ethernet PHY. The interface consists of a
10/100Mbit/s MII/RMII interface and an Ethernet MAC. In RMII operation, the interface contains seven signals with
a reference clock of 50 MHz. In MII operation, the interface contains 17 signals and a clock reference of 25MHz.
The DS33R11 can be configured to RMII or MII interface by the Hardware pin RMIIMIIS. If the port is configured for
MII in DCE mode, REF_CLK must be 25MHz. The DS33R11 will internally generate the TX_CLK and RX_CLK
outputs (at 25MHz for 100Mbps, 2.5MHz for 10Mbps) required for DCE mode from the REF_CLK input. In MII
mode with DTE operation, the TX_CLK and RX_CLK signals are generated by the PHY and are inputs to the
The data received from the MII or RMII interface is processed by the internal IEEE 802.3 compliant Ethernet MAC.
The user can select the maximum frame size (up to 2016 bytes) that is received with the SU.RMFSRH and
SU.RMFSRL multiplied by 8. Any programmed value greater than 2016 bytes will result in unpredictable
behavior and should be avoided. The maximum frame size is shown in Figure 9-4. The length includes only
destination address, source address, VLAN tag (2 bytes), type length field, data and CRC32. The frame size is
different than the 802.3 “type length field.”
Frames from the Ethernet PHY or received from the packet processor are rejected if greater than the maximum
frame size specified. Each Ethernet frame sent or received generates status bits (SU.TFSH and SU.TFSL and
SU.RFSB0 to SU.RFSB3). These are real-time status registers and will change as each frame is sent or received.
Hence they are useful to the user only when one frame is sent or received and the status is associated with the
frame sent or received.
Figure 9-4. IEEE 802.3 Ethernet Frame
Type
Lenght
Preamble
7
SFD
1
Destination Adrs
Source Address
Data
CRC32
4
6
6
2
46-1500
Max Frame Length
Encapsulated Frame
The distant end will normally reject the sent frames if jabber timeout, Loss of carrier, excessive deferral, late
collisions, excessive collisions, under run, deferred or collision errors occur. Transmission of a frame under any of
theses errors will generate a status bit in SU.TFSL, SU.TFSH. The DS33R11 provides user the option to
automatically retransmit the frame if any of the errors have occurred through the bit settings in SU.TFRC. Deferred
frames and heartbeat fail have separate resend control bits (SU.TFRC.TFBFCB and SU.TFRC.TPRHBC). If there
is no carrier (indicated by the MAC Transmit Packet Status), the transmit queue (data from the Serial Interface to
56 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
The MAC circuitry generates a frame status for every frame that is received. This real time status can be read by
SU.RFSB0 to SU.RFSB3. Note the frame status is the “real time” status and hence the value will change as new
frames are received. Hence the real time status reflects the status in time and may not correspond to the current
received frame being processed. This is also true for the transmitted frames.
Frames with errors are usually rejected by the DS33R11. The user has the option of accepting frames by settings
in Receive Frame Rejection Control register (SU.RFRC). The user can program whether to reject or accept frames
with the following errors:
•
•
•
•
MII error asserted during the reception of the frame
Dribbling bits occurred in the frame
CRC error occurred
Length error occurred—the length indicated by the frame length is inconsistent with the number of bytes
received
•
•
Control frame was received. The mode must be full duplex
Unsupported control frame was received
Note that frames received that are runt frames or frames with collision will automatically be rejected.
Table 9-5. Registers Related to Setting the Ethernet Port
REGISTER
NAME
FUNCTION
Transmit Frame Resend
Control
This register determines if the current frame is retransmitted
due to various transmit errors.
Transmit Frame Status Low
and Transmit Frame Status
High
SU.TFSL and
These two registers provide the real-time status of the
transmit frame. Only apply to the last frame transmitted.
Receive Frame Status Byte 0
to 3
These registers provide the real-time status for the received
frame. Only apply to the last frame received.
SU.RFSB0 to 3
Receive Frame Rejection
Control
This register provides settings for reception or rejection of
frame based on errors detected by the MAC.
Receiver Maximum Frame
High and Receiver Maximum
Frame Low
frames to be accepted from the MII/RMII receive interface.
MAC Control
This register provides configuration control for the MAC.
57 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.14.1 DTE and DCE Mode
The Ethernet MII/RMII port can be configured for DCE or DTE Mode. When the port is configured for the DTE
Mode it can be connected to an Ethernet PHY. In DCE mode, the port can be connected to MII/RMII MAC devices
other than an Ethernet PHY. The DTE/DCE connections for the DS33R11 in MII mode are shown in the following
two figures.
In DCE Mode, the DS33R11 transmitter is connected to an external receiver and DS33R11 receiver is connected
to an external MAC transmitter. The selection of DTE or DCE mode is done by the hardware pin DCEDTES.
Figure 9-5. Configured as DTE Connected to an Ethernet PHY in MII Mode
DS33R11
Rx
Ethernet Phy
Rx
RXD[3:0]
RXD[3:0]
DTE
DCE
RXDV
RXDV
RX_CLK
RX_CLK
RX_ERR
RX_CRS
RX_ERR
RX_CRS
COL_DET
MAC
COL_DET
TXD[3:0]
TXD[3:0]
Tx
TX_CLK
TX_EN
Tx
TX_CLK
TX_EN
MDIO
MDC
MDIO
MDC
58 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-6. DS33R11 Configured as a DCE in MII Mode
DS33Z11
DTE
Tx
DCE
Rx
TXD[3:0]
RXD[3:0]
TX_EN
RXDV
RX_CLK
TX_CLK
RX_ERR
RX_CRS
TX_ERR
RX_CRS
COL_DET
MAC
MAC
COL_DET
TXD[3:0]
TX_CLK
RXD[3:0]
RX_CLK
Tx
Rx
TX_EN
MDIO
RXDV
MDIO
MDC
MDC
9.15 Ethernet MAC
Indirect addressing is required to access the MAC register settings. Writing to the MAC registers requires the
SU.MACWD0-3 registers to be written with 4 bytes of data. The address for the write operation must be written to
to SU.MACRWC.MCS (MAC command status). MCS is cleared by the DS33R11 when the operation is complete.
Reading from the MAC registers requires the SU.MACRADH and SU.MACRADL registers to be written with the
address for the read operation. A read command is issued by writing a one to SU.MACRWC.MCRW and a zero to
clear, valid data is available in SU.MACRD0-SU.MACRD3. Note that only one operation can be initiated (read or
write) at one time. Data cannot be written or read from the MAC registers until the MCS bit has been cleared by the
device. The MAC registers are detailed in the following table.
59 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 9-6. MAC Control Registers
ADDRESS
REGISTER
DESCRIPTION
MAC Control Register. This register is used for programming full
duplex, half duplex, promiscuous mode, and back-off limit for half
duplex. The transmit and receive enable bits must be set for the MAC
to operate.
0000h-0003h
MAC MII Management (MDIO) Address Register. The address for
PHY access through the MDIO interface.
MAC MII (MDIO) Data Register. Data to be written to (or read from)
the PHY through MDIO interface.
0014h-0017h
0018h-001Bh
001Ch-001Fh
0100h-0103h
MAC Flow Control Register
SU.MMCCTRL MAC MMC Control Register. Bit 0 for resetting the status counters.
Table 9-7. MAC Status Registers
ADDRESS
0200h-0203h
0204h-0207h
0300h-0303h
0308h-030Bh
030Ch-030Fh
0334h-0337h
0338h-033Bh
REGISTER
DESCRIPTION
All frames received counter.
Number of received frames that are good.
Number of frames transmitted.
Number of bytes transmitted.
SU.TxBytesOkCtr Number of bytes transmitted with good frames.
Transmit FIFO underflow counter.
Transmit number of frames aborted.
60 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.15.1 MII Mode Options
The Ethernet interface can be configured for MII operation by setting the hardware pin RMIIMIIS low. The MII
interface consists of 17 pins. For instructions on clocking the Ethernet Interface while in MII mode, see Section 9.1.
9.15.2 RMII Mode
The Ethernet interface can be configured for RMII operation by setting the hardware pin RMIIMIIS high. RMII
interface operates synchronously from the external 50MHz reference (REF_CLK). Only seven signals are required.
The following figure shows the RMII architecture. Note that DCE mode is not supported for RMII mode and RMII is
valid only for full duplex operation.
Figure 9-7. RMII Interface
DS33R11 MAC
External PHY
TXD[1:0]
TX_EN
CRS_DV
RXD[1:0]
REF_CLK
61 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.15.3 PHY MII Management Block and MDIO Interface
The MII Management Block allows for the host to control up to 32 PHYs, each with 32 registers. The MII block
communicates with the external PHY using 2-wire serial interface composed of MDC (serial clock) and MDIO for
data. The MDIO data is valid on the rising edge of the MDC clock. The Frame format for the MII Management
Interface is shown Figure 9-8. The read/write control of the MII Management is accomplished through the indirect
SU.MACMIIA MII Management Address Register and data is passed through the indirect SU.MACMIID Data
Register. These indirect registers are accessed through the MAC Control Registers defined in Table 9-6. The MDC
clock is internally generated and runs at 1.67MHz.
Figure 9-8. MII Management Frame
Turn
Opco
de
Preamble
32 bits
Start
Phy Adrs
5 bits
Phy Reg
5 bits
Data
Idle
Aroun
d
2 bits
1
Bit
16
bits
2 bits
2 bits
111...111
111...111
01
01
10
01
PHYA[4:0]
PHYA[4:0]
PHYR[4:0]
PHYR[4:0]
ZZ
10
ZZZZZZZZZ
PHYD[15:0]
Z
Z
READ
WRITE
9.16 BERT in the Ethernet Mapper
The BERT in the Ethernet Mapper can be used for generation and detection of BERT patterns. The BERT is a
software programmable test pattern generator and monitor capable of meeting most error performance
requirements for digital transmission equipment. The following restrictions are related to the BERT:
•
•
•
•
•
The RDEN and TDEN are inputs that can be used to “gap” bits.
BERT will transmit even when the device is set for X.86 mode and TDEN is configured as an output.
The normal traffic flow is halted while the BERT is in operation.
If the BERT is enabled for a Serial port, it will override the normal connection.
If there is a connection overridden by the BERT, when BERT operation is terminated the normal operation is
restored.
The transmit direction generates the programmable test pattern, and inserts the test pattern payload into the data
stream. The receive direction extracts the test pattern payload from the receive data stream, and monitors the test
pattern payload for the programmable test pattern.
BERT Features
•
•
PRBS and QRSS patterns of 29-1, 215-1 223-1 and QRSS pattern support.
Programmable repetitive pattern. The repetitive pattern length and pattern are programmable.
[length n = 1 to 32 and pattern = 0 to (2n – 1)].
•
•
24-bit error count and 32-bit bit count registers.
Programmable bit error insertion. Errors can be inserted individually.
62 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.16.1 Receive Data Interface
9.16.1.1 Receive Pattern Detection
The Receive BERT receives only the payload data and synchronizes the receive pattern generator to the incoming
pattern. The receive pattern generator is a 32-bit shift register that shifts data from the least significant bit (LSB) or
bit 1 to the most significant bit (MSB) or bit 32. The input to bit 1 is the feedback. For a PRBS pattern (generating
polynomial xn + xy + 1), the feedback is an XOR of bit n and bit y. For a repetitive pattern (length n), the feedback is
bit n. The values for n and y are individually programmable (1 to 32). The output of the receive pattern generator is
the feedback. If QRSS is enabled, the feedback is an XOR of bits 17 and 20, and the output is forced to one if the
next 14 bits are all zeros. QRSS is programmable (on or off). For PRBS and QRSS patterns, the feedback is
forced to one if bits 1 through 31 are all zeros. Depending on the type of pattern programmed, pattern detection
performs either PRBS synchronization or repetitive pattern synchronization.
9.16.1.2 PRBS Synchronization
PRBS synchronization synchronizes the receive pattern generator to the incoming PRBS or QRSS pattern. The
receive pattern generator is synchronized by loading 32 data stream bits into the receive pattern generator, and
then checking the next 32 data stream bits. Synchronization is achieved if all 32 bits match the incoming pattern. If
at least is incoming bits in the current 64-bit window do not match the receive pattern generator, automatic pattern
resynchronization is initiated. Automatic pattern resynchronization can be disabled.
Figure 9-9. PRBS Synchronization State Diagram
Sync
1 bit error
Verify
Load
32 bits loaded
63 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.16.2 Repetitive Pattern Synchronization
Repetitive pattern synchronization synchronizes the receive pattern generator to the incoming repetitive pattern.
The receive pattern generator is synchronized by searching each incoming data stream bit position for the
repetitive pattern, and then checking the next 32 data stream bits. Synchronization is achieved if all 32 bits match
the incoming pattern. If at least sis incoming bits in the current 64-bit window do not match the receive PRBS
pattern generator, automatic pattern resynchronization is initiated. Automatic pattern resynchronization can be
disabled.
Figure 9-10. Repetitive Pattern Synchronization State Diagram
Sync
1 bit error
Verify
Match
Pattern Matches
9.16.3 Pattern Monitoring
Pattern monitoring monitors the incoming data stream for Out Of Synchronization (OOS) condition, bit errors, and
counts the incoming bits. An OOS condition is declared when the synchronization state machine is not in the
“Sync” state. An OOS condition is terminated when the synchronization state machine is in the “Sync” state.
Bit errors are determined by comparing the incoming data stream bit to the receive pattern generator output. If they
do not match, a bit error is declared, and the bit error and bit counts are incremented. If they match, only the bit
count is incremented. The bit count and bit error count are not incremented when an OOS condition exists.
9.16.4 Pattern Generation
Pattern Generation generates the outgoing test pattern, and passes it onto Error Insertion. The transmit pattern
generator is a 32-bit shift register that shifts data from the least significant bit (LSB) or bit 1 to the most significant
bit (MSB) or bit 32. The input to bit 1 is the feedback. For a PRBS pattern (generating polynomial xn + xy + 1), the
feedback is an XOR of bit n and bit y. For a repetitive pattern (length n), the feedback is bit n. The values for n and
y are individually programmable. The output of the receive pattern generator is the feedback. If QRSS is enabled,
the feedback is an XOR of bits 17 and 20, and the output is forced to one if the next 14 bits are all zeros. QRSS is
programmable (on or off). For PRBS and QRSS patterns, the feedback is forced to one if bits 1 through 31 are all
zeros. When a new pattern is loaded, the pattern generator is loaded with a pattern value before pattern generation
starts. The pattern value is programmable (0 – 2n - 1). When PRBS and QRSS patterns are generated the seed
value is all ones.
64 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.16.4.1 Error Insertion
Error insertion inserts errors into the outgoing pattern data stream. Errors are inserted one at a time Single bit error
insertion can be initiated from the microprocessor interface. If pattern inversion is enabled, the data stream is
inverted before the overhead/stuff bits are inserted. Pattern inversion is programmable (on or off).
9.16.4.2 Performance Monitoring Update
All counters stop counting at their maximum count. A counter register is updated by asserting (low to high
transition) the performance monitoring update signal (PMU). During the counter register update process, the
performance monitoring status signal (PMS) is de-asserted. The counter register update process consists of
loading the counter register with the current count, resetting the counter, forcing the zero count status indication
low for one clock cycle, and then asserting PMS. No events shall be missed during an update procedure.
9.17 Transmit Packet Processor
The Transmit Packet Processor accepts data from the Transmit FIFO, performs bit reordering, FCS processing,
packet error insertion, stuffing, packet abort sequence insertion, inter-frame padding, and packet scrambling. The
data output from the Transmit Packet Processor to the Transmit Serial Interface is a serial data stream (bit
synchronous mode). HDLC processing can be disabled (clear channel enable). Disabling HDLC processing
disables FCS processing, packet error insertion, stuffing, packet abort sequence insertion, and inter-frame
padding. Only bit reordering and packet scrambling are not disabled.
Bit reordering changes the bit order of each byte. If bit reordering is disabled, the outgoing 8-bit data stream
DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is output from the Transmit FIFO with the MSB in
TFD[7] (or 15, 23, or 31) and the LSB in TFD[0] (or 8, 16, or 24) of the transmit FIFO data TFD[7:0] 15:8, 23:16, or
31:24). If bit reordering is enabled, the outgoing 8-bit data stream DT[1:8] is output from the Transmit FIFO with the
MSB in TFD[0] and the LSB in TFD[7] of the transmit FIFO data TFD[7:0]. In bit synchronous mode, DT [1] is the
first bit transmitted.
FCS processing calculates an FCS and appends it to the packet. FCS calculation is a CRC-16 or CRC-32
calculation over the entire packet. The polynomial used for FCS-16 is x16 + x12 + x5 + 1. The polynomial used for
FCS-32 is x32 + x26 + x23 + x22 + x16 + x12 + x11 + x10 + x8 + x7 + x5 + x4 + x2 + x + 1. The FCS is inverted after
calculation. The FCS type is programmable. If FCS append is enabled, the calculated FCS is appended to the
packet. If FCS append is disabled, the packet is transmitted without an FCS. The FCS append mode is
programmable. If packet processing is disabled, FCS processing is not performed.
Packet error insertion inserts errors into the FCS bytes. A single FCS bit is corrupted in each errored packet. The
FCS bit corrupted is changed from errored packet to errored packet. Error insertion can be controlled by a register
or by the manual error insertion input (LI.TMEI.TMEI). The error insertion initiation type (register or input) is
programmable. If a register controls error insertion, the number and frequency of the errors are programmable. If
FCS append is disabled, packet error insertion will not be performed. If packet processing is disabled, packet error
insertion is not performed.
Stuffing inserts control data into the packet to prevent packet data from mimicking flags. A packet start indication is
received, and stuffing is performed until, a packet end indication is received. Bit stuffing consists of inserting a '0'
directly following any five contiguous '1's. If packet processing is disabled, stuffing is not performed.
There is at least one flag plus a programmable number of additional flags between packets. The inter-frame fill can
be flags or all '1's followed by a start flag. If the inter-frame fill is all '1's, the number of '1's between the end and
start flags does not need to be an integer number of bytes, however, there must be at least 15 consecutive '1's
between the end and start flags. The inter-frame padding type is programmable. If packet processing is disabled,
inter-frame padding is not performed.
Packet abort insertion inserts a packet abort sequences as necessary. If a packet abort indication is detected, a
packet abort sequence is inserted and inter-frame padding is done until a packet start flag is detected. The abort
sequence is FFh. If packet processing is disabled, packet abort insertion is not performed.
The packet scrambler is a x43 + 1 scrambler that scrambles the entire packet data stream. The packet scrambler
runs continuously, and is never reset. In bit synchronous mode, scrambling is performed one bit at a time. In byte
synchronous mode, scrambling is performed 8 bits at a time. Packet scrambling is programmable.
Once all packet processing has been completed serial data stream is passed on to the Transmit Serial Interface.
65 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.18 Receive Packet Processor
The Receive Packet Processor accepts data from the Receive Serial Interface performs packet descrambling,
packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error
monitoring, FCS byte extraction, and bit reordering. The data coming from the Receive Serial Interface is a serial
data stream. Packet processing can be disabled (clear channel enable). Disabling packet processing disables
packet delineation, inter-frame fill filtering, packet abort detection, destuffing, packet size checking, FCS error
monitoring, and FCS byte extraction. Only packet descrambling and bit reordering are not disabled.
The packet descrambler is a self-synchronous x43 + 1 descrambler that descrambles the entire packet data stream.
Packet descrambling is programmable. The descrambler runs continuously, and is never reset. The descrambling
is performed one bit at a time. Packet descrambling is programmable. If packet processing is disabled, the serial
data stream is demultiplexed in to an 8-bit data stream before being passed on.
If packet processing is disabled, a packet boundary is arbitrarily chosen and the data is divided into "packets" of
programmable size (dependent on maximum packet size setting). These packets are then passed on to bit
reordering with packet start and packet end indications. Data then bypasses packet delineation, inter-frame fill
filtering, packet abort detection, destuffing, packet size checking, FCS error monitoring, and FCS byte extraction.
Packet delineation determines the packet boundary by identifying a packet start or end flag. Each time slot is
checked for a flag sequence (7Eh). Once a flag is found, it is identified as a start/end flag and the packet boundary
is set. The flag check is performed one bit at a time. If packet processing is disabled, packet delineation is not
performed.
Inter-frame fill filtering removes the inter-frame fill between packets. When a packet end flag is detected, all data is
discarded until a packet start flag is detected. The inter-frame fill can be flags or all '1's. The number of '1's
between flags does not need to be an integer number of bytes, and if at least 7 '1's are detected in the first 16 bits
after a flag, all data after the flag is discarded until a start flag is detected. There may be only one flag between
packets. When the inter-frame fill is flags, the flags may have a shared zero (011111101111110). If there is less
than 16 bits between two flags, the data is discarded. If packet processing is disabled, inter-frame fill filtering is not
performed.
Packet abort detection searches for a packet abort sequence. Between a packet start flag and a packet end flag, if
an abort sequence is detected, the packet is marked with an abort indication, the aborted packet count is
incremented, and all subsequent data is discarded until a packet start flag is detected. The abort sequence is
seven consecutive ones. If packet processing is disabled, packet abort detection is not performed.
Destuffing removes the extra data inserted to prevent data from mimicking a flag or an abort sequence. A start flag
is detected, a packet start is set, the flag is discarded, destuffing is performed until an end flag is detected, a
packet end is set, and the flag is discarded. In bit synchronous mode, bit destuffing is performed. Bit destuffing
consists of discarding any '0' that directly follows five contiguous '1's. After destuffing is completed, the serial bit
stream is demultiplexed into an 8-bit parallel data stream and passed on with packet start, packet end, and packet
abort indications. If there is less than eight bits in the last byte, an invalid packet flag is raised, the packet is tagged
with an abort indication, and the packet size violation count is incremented. If packet processing is disabled,
destuffing is not performed.
Packet size checking checks each packet for a programmable maximum and programmable minimum size. As the
packet data comes in, the total number of bytes is counted. If the packet length is below the minimum size limit, the
packet is marked with an aborted indication, and the packet size violation count is incremented. If the packet length
is above the maximum size limit, the packet is marked with an aborted indication, the packet size violation count is
incremented, and all packet data is discarded until a packet start is received. The minimum and maximum lengths
include the FCS bytes, and are determined after destuffing has occurred. If packet processing is disabled, packet
size checking is not performed.
FCS error monitoring checks the FCS and aborts errored packets. If an FCS error is detected, the FCS errored
packet count is incremented and the packet is marked with an aborted indication. If an FCS error is not detected,
the receive packet count is incremented. The FCS type (16-bit or 32-bit) is programmable. If FCS processing or
packet processing is disabled, FCS error monitoring is not performed.
FCS byte extraction discards the FCS bytes. If FCS extraction is enabled, the FCS bytes are extracted from the
packet and discarded. If FCS extraction is disabled, the FCS bytes are stored in the receive FIFO with the packet.
If FCS processing or packet processing is disabled, FCS byte extraction is not performed.
66 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Bit reordering changes the bit order of each byte. If bit reordering is disabled, the incoming 8-bit data stream
DT[1:8] with DT[1] being the MSB and DT[8] being the LSB is output to the Receive FIFO with the MSB in RFD[7]
(or 15, 23, or 31) and the LSB in RFD[0] (or 8, 16, or 24) of the receive FIFO data RFD[7:0] (or 15:8, 23:16, or
31:24). If bit reordering is enabled, the incoming 8-bit data stream DT[1:8] is output to the Receive FIFO with the
MSB in RFD[0] and the LSB in RFD[7] of the receive FIFO data RFD[7:0]. DT[1] is the first bit received from the
incoming data stream.
Once all of the packet processing has been completed, The 8-bit parallel data stream is demultiplexed into a 32-bit
parallel data stream. The Receive FIFO data is passed on to the Receive FIFO with packet start, packet end,
packet abort, and modulus indications. At a packet end, the 32-bit word may contain 1, 2, 3, or 4 bytes of data
depending on the number of bytes in the packet. The modulus indications indicate the number of bytes in the last
data word of the packet.
Figure 9-11. HDLC Encapsulation of MAC Frame
Number of Bytes
1
6
6
2
Flag(0x7E)
Destination Adrs(DA)
Source Adrs(SA)
Length/Type
46-1500
MAC Client Data
PAD
4
FCS for MAC
FCS for HDLC
Flag(0x7E)
0 / 2 / 4
MSB
LSB
67 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.19 X.86 Encoding and Decoding
X.86 protocol provides a method for encapsulating Ethernet Frame onto LAPS. LAPS provides HDLC type framing
structure for encapsulation of Ethernet frames. LAPS encapsulated frames can be used to send data onto a
SONET/SDH network. The DS33R11 expects a byte synchronization signal to provide the byte boundary for the
X.86 receiver. This is provided by the RBSYNC pin. The functional timing is shown in Figure 12-4. The X.86
transmitter provides a byte boundary indicator with the signal TBSYNC. The functional timing is shown in
Figure 12-3. Note that in some cases, additional logic may be required to meet RSYNC/TSYNC sychronization
timing requirements when operating in X.86 mode.
Figure 9-12. LAPS Encoding of MAC Frames Concept
IEEE
802.3 MAC Frame
LAPS
Rate Adaption
SDH
68 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 9-13. X.86 Encapsulation of the MAC frame
Number of Bytes
Flag(0x7E)
Address(0x04)
1
1
Control(0x03)
1
1
1
6
6
1st Octect of SAPI(0xfe)
2nd Octect of SAPI(0x01)
Destination Adrs(DA)
Source Adrs(SA)
Length/Type
2
46-1500
MAC Client Data
PAD
4
4
FCS for MAC
FCS for LAPS
Flag(0x7E)
MSB
LSB
The DS33R11 will encode the MAC Frame with the LAPS encapsulation on a complete serial stream if configured
•
•
•
Control Registers for Address, Control, SAPIH, SAPIL.
32 bit FCS enabled.
Programmable X43+1 scrambling.
The sequence of processing performed by the receiver is as follows:
•
•
•
•
•
•
•
Programmable octets X43+1 descrambling.
Detect the Start Flag (7E).
Remove Rate adaptation octets 7d, dd.
Perform transparency-processing 7d, 5e is converted to 7e and 7d, 5d is converted to 7d.
Perform FCS checking.
Detect the closing flag.
69 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
The X86 received frame is aborted if:
•
•
•
•
•
If 7d,7E is detected. This is an abort packet sequence in X.86.
Invalid FCS is detected.
The received frame has less than 6 octets.
Control, SAPI and address field are mismatched to the programmed value.
Octet 7d and octet other than 5d,5e,7e or dd is detected.
For the transmitter if X.86 is enabled the sequence of processing is as follows:
•
•
•
•
•
Construct frame including start flag, SAPI, Control and MAC frame.
Calculate FCS.
Perform transparency processing - 7E is translated to 7D5E, 7D is translated to 7D5D.
Append the end flag(7E).
Scramble the sequence X43+1.
Note that the serial transmit and receive registers apply to the X.86 implementations with specific exceptions. The
exceptions are outlined in the serial interface transmit and receive register sections.
70 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
9.20 Committed Information Rate Controller
The DS33R11 provides a CIR provisioning facility. The CIR can be used restricts the transport of received MAC
data to a programmable rate. The CIR location is shown in the Figure 6-1. The CIR will restrict the data flow from
the Receive MAC to Transmit HDLC. This can be used for provisioning and billing functions towards the WAN. The
user must set the CIR register to control the amount of data throughput from the MAC to HDLC transmit. The CIR
register is in granularity of 500kbit/s with a range of 0 to 52Mbit/s. The operation of the CIR is as follows:
•
•
The CIR block counts the credits that are accumulated at the end of every 125ms.
If data is received and stored in the SDRAM to be sent to the Serial Interface, the interface will request the
data if there is a positive credit balance. If the credit balance is negative, transmit interface does not
request data.
•
New credit balance is calculated credit balance = old credit balance – frame size in bytes after the frame
is sent.
•
•
•
•
The credit balance is incremented every 125ms by CIR/8.
Credit balances not used in 250ms are reset to 0.
The maximum value of CIR can not exceed the transmit line rate.
If the data rate received from the Ethernet interface is higher than the CIR, the receive queue buffers will fill
and the high threshold water mark will invoke flow control to reduce the incoming traffic rate.
•
•
The CIR function is only available for software mode of operation only.
CIR function is only available in data received at the Ethernet Interface to be sent to WAN. There is not
CIR functionality for data arriving from the WAN to be sent to the Ethernet Interface.
•
Negative credits are not allowed, if there is not a credit balance, no frames are sent until there is a credit
balance again.
71 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10 INTEGRATED T1/E1/J1 TRANSCEIVER
10.1 T1/E1/J1 Clocks
Figure 10-1 shows the clock map of the T1/E1 transceiver. The routing for the transmit and receive clocks are
shown for the various loopback modes and jitter attenuator positions. Although there is only one jitter attenuator,
which can be placed in the receive or transmit path, two are shown for simplification and clarity.
Figure 10-1. T1/E1/J1 Clock Map
MCLK
TSYSCLK
MCLKS = 0
MCLKS = 1
TR.LIC4.MPS0
TR.LIC4.MPS1
PRE-SCALER
2.048 TO 1.544
SYNTHESIZER
TR.LIC2.3
DJA = 1
DJA = 0
8 x PLL
8XCLK
LOCAL
JITTER ATTENUATOR
LOOPBACK
SEE TR.LIC1
REGISTER
REMOTE
LOOPBACK
FRAMER
LOOPBACK
PAYLOAD
LOOPBACK
(SEE NOTES)
RCL = 1
JAS = 0
AND
BPCLK
SYNTH
LLB = 0
LLB = 1
BPCLK
RCLK
DJA = 0
FLB = 0
FLB = 1
LTCA
RXCLK
RECEIVE
FRAMER
RCL = 0
JAS = 1
OR
DJA = 1
TO
LIU
JAS = 0
OR
DJA = 1
RLB = 1
RLB = 0
PLB = 1
PLB = 0
TXCLK
LTCA
TRANSMIT
FORMATTER
JAS = 1
AND
DJA = 0
TCLKT
MUX
A
B
C
TCLKT
The TCLKT MUX is dependent on the state of the TCSS0 and TCSS1 bits in the TR.CCR1 register and the state of
the TCLKT pin.
72 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 10-1. T1/E1/J1 Transmit Clock Source
TCSS1
TCSS0
TRANSMIT CLOCK SOURCE
0
0
1
1
0
1
0
1
The TCLKT pin (C) is always the source of transmit clock.
Switch to the recovered clock (B) when the signal at the TCLKT pin
fails to transition after one channel time.
Use the scaled signal (A) derived from MCLK as the transmit clock.
The TCLKT pin is ignored.
Use the recovered clock (B) as the transmit clock. The TCLKT pin is
ignored.
10.2 Per-Channel Operation
Some of the features described in the data sheet that operate on a per-channel basis use a special method for
channel selection. There are five registers involved: per-channel pointer register (TR.PCPR) and per-channel data
registers 1–4 (TR.PCDR1–4). The user selects which function or functions are to be applied on a per-channel
basis by setting the appropriate bit(s) in the TR.PCPR register. The user then writes to the TR.PCDR registers to
select the channels for that function. The following is an example of mapping the transmit and receive BERT
function to channels 9–12, 20, and 21.
Write 11h to TR.PCPR
Write 00h to TR.PCDR1
Write 0fh to TR.PCDR2
Write 18h to TR.PCDR3
Write 00h to TR.PCDR4
The user may write to the TR.PCDR1-4 with multiple functions in the TR.PCPR register selected, but can only read
the values from the TR.PCDR1-4 registers for a single function at a time. More information about how to use these
10.3 T1/E1/J1 Transceiver Interrupts
Various alarms, conditions, and events in the T1/E1/J1 transceiver can cause interrupts. For simplicity, these are
all referred to as events in this explanation. All status registers can be programmed to produce interrupts. Each
status register has an associated interrupt mask register. For example, TR.SR1 (status register 1) has an interrupt
control register called TR.IMR1 (interrupt mask register 1). Status registers are the only sources of interrupts in the
device. On power-up, all writeable registers of the T1/E1/J1 transceiver are automatically cleared. Since bits in the
TR.IMRx registers have to be set = 1 to allow a particular event to cause an interrupt, no interrupts can occur until
the host selects which events are to product interrupts. Since there are potentially many sources of interrupts on
the device, several features are available to help sort out and identify which event is causing an interrupt. When an
interrupt occurs, the host should first read the TR.IIR1 and TR.IIR2 registers (interrupt information registers) to
identify which status register (or registers) is producing the interrupt. Once that is determined, the individual status
register or registers can be examined to determine the exact source.
Once an interrupt has occurred, the interrupt handler routine should set the INTDIS bit (TR.CCR3.6) to stop further
activity on the interrupt pin. After all interrupts have been determined and processed, the interrupt hander routine
should re-enable interrupts by setting the INTDIS bit = 0.
73 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.4 T1 Framer/Formatter Control and Status
The T1 framer portion of the transceiver is configured through a set of nine control registers. Typically, the control
registers are only accessed when the system is first powered up. Once the transceiver has been initialized, the
control registers only need to be accessed when there is a change in the system configuration. There are two
receive control registers (TR.T1RCR1 and TR.T1RCR2), two transmit control registers (TR.T1TCR1 and
TR.T1TCR2), and a common control register (TR.T1CCR1). Each of these registers is described in this section.
10.4.1 T1 Transmit Transparency
The software signaling insertion-enable registers, TR.SSIE1–TR.SSIE4, can be used to select signaling insertion
from the transmit signaling registers, TS1–TS12, on a per-channel basis. Setting a bit in the SSIEx register allows
signaling data to be sourced from the signaling registers for that channel.
In transparent mode, bit 7 stuffing and/or robbed-bit signaling is prevented from overwriting the data in the
channels. If a DS0 is programmed to be clear, no robbed-bit signaling is inserted nor does the channel have bit 7
stuffing performed. However, in the D4 framing mode, bit 2 is overwritten by a 0 when a Yellow Alarm is
transmitted. Also, the user has the option to globally override the TR.SSIEx registers from determining which
channels are to have bit 7 stuffing performed. If the TR.T1TCR1.3 and TR.T1TCR2.0 bits are set to 1, then all 24
T1 channels have bit 7 stuffing performed on them, regardless of how the TR.SSIEx registers are programmed. In
this manner, the TR.SSIEx registers are only affecting the channels that are to have robbed-bit signaling inserted
into them.
10.4.2 AIS-CI and RAI-CI Generation and Detection
The device can transmit and detect the RAI-CI and AIS-CI codes in T1 mode. These codes are compatible with
and do not interfere with the standard RAI (Yellow) and AIS (Blue) alarms. These codes are defined in ANSI
T1.403.
The AIS-CI code (alarm indication signal-customer installation) is the same for both ESF and D4 operation. Setting
the TAIS-CI bit in the TR.T1CCR1 register and the TBL bit in the TR.T1TCR1 register causes the device to
transmit the AIS-CI code. The RAIS-CI status bit in the TR.SR4 register indicates the reception of an AIS-CI signal.
The RAI-CI (remote alarm indication-customer installation) code for T1 ESF operation is a special form of the ESF
Yellow Alarm (an unscheduled message). Setting the RAIS-CI bit in the TR.T1CCR1 register causes the device to
transmit the RAI-CI code. The RAI-CI code causes a standard Yellow Alarm to be detected by the receiver. When
the host processor detects a Yellow Alarm, it can then test the alarm for the RAI-CI state by checking the BOC
detector for the RAI-CI flag. That flag is a 011111 code in the 6-bit BOC message.
The RAI-CI code for T1 D4 operation is a 10001011 flag in all 24 time slots. To transmit the RAI-CI code the host
sets all 24 channels to idle with a 10001011 idle code. Since this code meets the requirements for a standard T1
D4 Yellow Alarm, the host can use the receive channel monitor function to detect the 100001011 code whenever a
standard Yellow Alarm is detected.
74 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.4.3 T1 Receive-Side Digital-Milliwatt Code Generation
Receive-side digital-milliwatt code generation involves using the receive digital-milliwatt registers
(TR.T1RDMR1/2/3) to determine which of the 24 T1 channels of the T1 line going to the backplane should be
overwritten with a digital-milliwatt pattern. The digital-milliwatt code is an 8-byte repeating pattern that represents a
1kHz sine wave (1E/0B/0B/1E/9E/8B/8B/9E). Each bit in the TR.T1RDMRx registers represents a particular
channel. If a bit is set to a 1, then the receive data in that channel is replaced with the digital-milliwatt code. If a bit
is set to 0, no replacement occurs.
Table 10-2. T1 Alarm Criteria
ALARM
Blue Alarm (AIS)
(Note 1)
SET CRITERIA
CLEAR CRITERIA
When over a 3ms window, five or
fewer 0s are received
When over a 3ms window, six or
more 0s are received
When bit 2 of 256 consecutive
channels is set to 0 for at least 254
occurrences
When bit 2 of 256 consecutive
channels is set to 0 for fewer than
254 occurrences
Yellow Alarm (RAI)
D4 Bit 2 Mode
(TR.T1RCR2.0 = 0)
D4 12th F-Bit Mode
When the 12th framing bit is set to 1 When the 12th framing bit is set to
(TR.T1RCR2.0 = 1; this mode is
also referred to as the “Japanese
Yellow Alarm”)
for two consecutive occurrences
0 for two consecutive occurrences
ESF Mode
When 16 consecutive patterns of
00FF appear in the FDL
When 14 or fewer patterns of 00FF
hex out of 16 possible appear in
the FDL
When 192 consecutive 0s are
received
When 14 or more 1s out of 112
possible bit positions are received
Red Alarm (LRCL)
(Also referred to as loss of signal)
Note 1: The definition of Blue Alarm (or AIS) is an unframed all-ones signal. Blue Alarm detectors should be able to operate properly in the
presence of a 10E-3 error rate and they should not falsely trigger on a framed all-1s signal. Blue Alarm criteria in the device has been
set to achieve this performance. It is recommended that the RBL bit be qualified with the RLOS bit.
Note 2: ANSI specifications use a different nomenclature than this document. The following terms are equivalent:
RBL = AIS
RCL = LOS
RLOS = LOF
RYEL = RAI
75 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.5 E1 Framer/Formatter Control and Status
The E1 framer portion of the transceiver is configured by a set of four control registers. Typically, the control
registers are only accessed when the system is first powered up. Once the device has been initialized, the control
registers need only to be accessed when there is a change in the system configuration. There are two receive
control registers (TR.E1RCR1 and TR.E1RCR2) and two transmit control registers (TR.E1TCR1 and TR.E1TCR2).
There are also four status and information registers. Each of these eight registers is described in this section.
Table 10-3. E1 Sync/Resync Criteria
FRAME OR
MULTIFRAME
LEVEL
SYNC CRITERIA
RESYNC CRITERIA
ITU SPEC.
Three consecutive incorrect
FAS received
FAS present in frame N and
N + 2; FAS not present in Alternate: (TR.E1RCR1.2 = 1)
frame N + 1
G.706
4.1.1
4.1.2
FAS
The above criteria is met or
three consecutive incorrect bit
2 of non-FAS received
Two valid MF alignment
words found within 8ms
Valid MF alignment word
found and previous time slot
16 contains code other than
all 0s
915 or more CRC4 codewords
out of 1000 received in error
G.706
4.2 and 4.3.2
CRC4
CAS
Two consecutive MF alignment
words received in error
G.732
5.2
76 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.5.1 Automatic Alarm Generation
The device can be programmed to automatically transmit AIS or remote alarm. When automatic AIS generation is
enabled (TR.E1TCR2.1 = 1), the device monitors the receive-side framer to determine if any of the following
conditions are present: loss-of-receive frame synchronization, AIS alarm (all ones) reception, or loss-of-receive
carrier (or signal). The framer forces either an AIS or remote alarm if any one or more of these conditions is
present.
When automatic RAI generation is enabled (TR.E1TCR2.0 = 1), the framer monitors the receive side to determine
if any of the following conditions are present: loss-of-receive-frame synchronization, AIS alarm (all ones) reception,
loss-of-receive carrier (or signal), or if CRC4 multiframe synchronization cannot be found within 128ms of FAS
synchronization (if CRC4 is enabled). If any one or more of these conditions is present, then the framer transmits
an RAI alarm. RAI generation conforms to ETS 300 011 specifications and a constant remote alarm is transmitted
if the device cannot find CRC4 multiframe synchronization within 400ms as per G.706.
Note: It is an invalid state to have both automatic AIS generation and automatic remote alarm generation enabled
at the same time.
Table 10-4. E1 Alarm Criteria
ITU
ALARM
SET CRITERIA
CLEAR CRITERIA
SPECIFICATION
An RLOS condition exists on power-up
prior to initial synchronization, when a
resync criteria has been met, or when a
manual resync has been initiated by
TR.E1RCR1.0
RLOS
RCL
255 or 2048 consecutive 0s received as
determined by TR.E1RCR2.0
At least 32 1s in 255-bit times
are received
G.775/G.962
Bit 3 of nonalign frame set to
0 for three consecutive
occasions
Bit 3 of nonalign frame set to 1 for three
consecutive occasions
O.162
2.1.4
RRA
Fewer than three 0s in two frames (512
bits)
Bit 6 of time slot 16 in frame 0 has been set
for two consecutive multiframes
More than two 0s in two
frames (512 bits)
O.162
1.6.1.2
RUA1
RDMA
V52LNK
Two out of three Sa7 bits are 0
G.965
10.6 Per-Channel Loopback
The per-channel loopback registers (PCLRs) determine which channels (if any) from the backplane should be
replaced with the data from the receive side or, i.e., off of the T1 or E1 line. If this loopback is enabled, then
transmit and receive clocks and frame syncs must be synchronized. One method to accomplish this is to connect
RCLKO to TCLKT and RFSYNC to TSYNC. There are no restrictions on which channels can be looped back or on
how many channels can be looped back.
Each of the bit positions in the per-channel loopback registers (TR.PCLR1/TR.PCLR2/TR.PCLR3/TR.PCLR4)
represents a DS0 channel in the outgoing frame. When these bits are set to a 1, data from the corresponding
receive channel replaces the data on TSERI for that channel.
77 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.7 Error Counters
The transceiver contains four counters that are used to accumulate line-coding errors, path errors, and
synchronization errors. Counter update options include one-second boundaries, 42ms (T1 mode only), 62ms (E1
mode only), or manual. See Error-Counter Configuration Register (TR.ERCNT). When updated automatically, the
user can use the interrupt from the timer to determine when to read these registers. All four counters saturate at
their respective maximum counts, and they do not roll over. Note: Only the line-code violation count register has
the potential to overflow, but the bit error would have to exceed 10E-2 before this would occur.
10.7.1 Line-Code Violation Counter (TR.LCVCR)
In T1 mode, code violations are defined as bipolar violations (BPVs) or excessive 0s. If the B8ZS mode is set for
the receive side, then B8ZS codewords are not counted. This counter is always enabled; it is not disabled during
Table 10-5 T1 Line Code Violation Counting Options
COUNT EXCESSIVE
B8ZS ENABLED?
ZEROS?
COUNTED IN THE LCVCRs
BPVs
BPVs + 16 consecutive 0s
BPVs (B8ZS codewords not counted)
BPVs + 8 consecutive 0s
(TR.T1RCR2.5)
(TR.ERCNT.0)
No
Yes
No
No
No
Yes
Yes
Yes
In E1 mode, either bipolar violations or code violations can be counted. Bipolar violations are defined as
consecutive marks of the same polarity. In this mode, if the HDB3 mode is set for the receive side, then HDB3
codewords are not counted as BPVs. If TR.ERCNT.3 is set, then the LVC counts code violations as defined in ITU
O.161. Code violations are defined as consecutive bipolar violations of the same polarity. In most applications, the
framer should be programmed to count BPVs when receiving AMI code and to count CVs when receiving HDB3
code. This counter increments at all times and is not disabled by loss-of-sync conditions. The counter saturates at
65,535 and does not roll over. The bit-error rate on an E1 line would have to be greater than 10-2 before the VCR
Table 10-6. E1 Line-Code Violation Counting Options
E1 CODE VIOLATION SELECT
COUNTED IN THE LCVCRs
(TR.ERCNT.3)
0
1
BPVs
CVs
78 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.7.2 Path Code Violation Count Register (TR.PCVCR)
In T1 mode, the path code violation count register records Ft, Fs, or CRC6 errors in T1 frames. When the receive
side of a framer is set to operate in the T1 ESF framing mode, TR.PCVCR records errors in the CRC6 codewords.
When set to operate in the T1 D4 framing mode, TR.PCVCR counts errors in the Ft framing bit position. Through
the TR.ERCNT.2 bit, a framer can be programmed to also report errors in the Fs framing bit position. The
TR.PCVCR is disabled during receive loss-of-synchronization (RLOS = 1) conditions. Table 10-7 shows what
errors the TR.PCVCR counts.
Table 10-7. T1 Path Code Violation Counting Arrangements
COUNTED
IN THE PCVCRs
FRAMING MODE
COUNT Fs ERRORS?
D4
D4
ESF
No
Yes
Don’t Care
Errors in the Ft pattern
Errors in both the Ft and Fs patterns
Errors in the CRC6 codewords
In E1 mode, the path code violation-count register records CRC4 errors. Since the maximum CRC4 count in a one-
second period is 1000, this counter cannot saturate. The counter is disabled during loss-of-sync at either the FAS
or CRC4 level; it continues to count if loss-of-multiframe sync occurs at the CAS level.
Path code violation-count register 1 (TR.PCVCR1) is the most significant word and TR.PCVCR2 is the least
significant word of a 16-bit counter that records path violations (PVs).
79 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.7.3 Frames Out-of-Sync Count Register (TR.FOSCR)
In T1 mode, TR.FOSCR is used to count the number of multiframes that the receive synchronizer is out of sync.
This number is useful in ESF applications needing to measure the parameters loss-of-frame count (LOFC) and
ESF error events as described in AT&T publication TR54016. When TR.FOSCR is operated in this mode, it is not
disabled during receive loss-of-synchronization (RLOS = 1) conditions. TR.FOSCR has an alternate operating
mode whereby it counts either errors in the Ft framing pattern (in the D4 mode) or errors in the FPS framing pattern
(in the ESF mode). When TR.FOSCR is operated in this mode, it is disabled during receive loss-of-synchronization
Table 10-8. T1 Frames Out-of-Sync Counting Arrangements
COUNT MOS OR
FRAMING MODE
(TR.T1RCR1.3)
F-BIT ERRORS
(TR.ERCNT.1)
MOS
COUNTED IN THE FOSCRs
D4
D4
Number of multiframes out-of-sync
Errors in the Ft pattern
F-Bit
ESF
ESF
MOS
F-Bit
Number of multiframes out-of-sync
Errors in the FPS pattern
In E1 mode, TR.FOSCR counts word errors in the FAS in time slot 0. This counter is disabled when RLOS is high.
FAS errors are not counted when the framer is searching for FAS alignment and/or synchronization at either the
CAS or CRC4 multiframe level. Since the maximum FAS word error count in a one-second period is 4000, this
counter cannot saturate.
The frames out-of-sync count register 1 (TR.FOSCR1) is the most significant word and TR.FOSCR2 is the least
significant word of a 16-bit counter that records frames out-of-sync.
10.7.4 E-Bit Counter (TR.EBCR)
This counter is only available in E1 mode. E-bit count register 1 (TR.EBCR1) is the most significant word and
TR.EBCR2 is the least significant word of a 16-bit counter that records far-end block errors (FEBE) as reported in
the first bit of frames 13 and 15 on E1 lines running with CRC4 multiframe. These count registers increment once
each time the received E-bit is set to 0. Since the maximum E-bit count in a one-second period is 1000, this
counter cannot saturate. The counter is disabled during loss-of-sync at either the FAS or CRC4 level; it continues
to count if loss-of-multiframe sync occurs at the CAS level.
80 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.8 DS0 Monitoring Function
The transceiver has the ability to monitor one DS0 64kbps channel in the transmit direction and one DS0 channel
in the receive direction at the same time. In the transmit direction, the user determines which channel is to be
monitored by properly setting the TCM0 to TCM4 bits in the TR.TDS0SEL register. In the receive direction, the
RCM0 to RCM4 bits in the TR.RDS0SEL register need to be properly set. The DS0 channel pointed to by the
TCM0 to TCM4 bits appear in the transmit DS0 monitor (TR.TDS0M) register. The DS0 channel pointed to by the
RCM0 to RCM4 bits appear in the receive DS0 (TR.RDS0M) register. The TCM4 to TCM0 and RCM4 to RCM0
bits should be programmed with the decimal decode of the appropriate T1or E1 channel. T1 channels 1 through 24
map to register values 0 through 23. E1 channels 1 through 32 map to register values 0 through 31. For example,
if DS0 channel 6 in the transmit direction and DS0 channel 15 in the receive direction needed to be monitored,
then the following values would be programmed into TR.TDS0SEL and TR.RDS0SEL:
TCM4 = 0
TCM3 = 0
TCM2 = 1
TCM1 = 0
TCM0 = 1
RCM4 = 0
RCM3 = 1
RCM2 = 1
RCM1 = 1
RCM0 = 0
81 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.9 Signaling Operation
There are two methods to access receive signaling data and provide transmit signaling data, processor-based
(software-based) or hardware-based. Processor-based refers to access through the transmit and receive signaling
registers RS1–RS16 and TS1–TS16. Hardware-based refers to the TSIG and RSIG pins. Both methods can be
used simultaneously.
Figure 10-2. Simplified Diagram of Receive Signaling Path
PER-CHANNEL
CONTROL
T1/E1 DATA STREAM
ALL-ONES
RSERO
SIGNALING
EXTRACTION
RECEIVE SIGNALING
REINSERTION
RSYNC
RSIG
REGISTERS
CONTROL
SIGNALING
BUFFERS
CHANGE-OF-STATE
INDICATION
REGISTERS
10.9.1 Processor-Based Receive Signaling
The robbed-bit signaling (T1) or TS16 CAS signaling (E1) is sampled in the receive data stream and copied into
the receive signaling registers, RS1–RS16. In T1 mode, only RS1–RS12 are used. The signaling information in
these registers is always updated on multiframe boundaries. This function is always enabled.
10.9.1.1 Change-of-State
To avoid constant monitoring of the receive signaling registers, the transceiver can be programmed to alert the
host when any specific channel or channels undergo a change of their signaling state. TR.RSCSE1–TR.RSCSE4
for E1 and TR.RSCSE1–TR.RSCSE3 for T1 are used to select which channels can cause a change-of-state
indication. The change-of-state is indicated in status register 5 (TR.SR1.5). If signaling integration (TR.CCR1.5) is
enabled, then the new signaling state must be constant for three multiframes before a change-of-state is indicated.
The user can enable the INT pin to toggle low upon detection of a change in signaling by setting the TR.IMR1.5 bit.
The signaling integration mode is global and cannot be enabled on a channel-by-channel basis.
The user can identity which channels have undergone a signaling change-of-state by reading the TR.RSINFO1–
TR.RSINFO4 registers. The information from these registers inform the user which TR.RSx register to read for the
new signaling data. All changes are indicated in the TR.RSINFO1–TR.RSINFO4 registers regardless of the
TR.RSCSE1–TR.RSCSE4 registers.
82 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.9.2 Hardware-Based Receive Signaling
In hardware-based signaling the signaling data can be obtained from the RSERO pin or the RSIG pin. RSIG is a
signaling PCM stream output on a channel-by-channel basis from the signaling buffer. The signaling data, T1
robbed bit or E1 TS16, is still present in the original data stream at RSERO. The signaling buffer provides signaling
data to the RSIG pin and also allows signaling data to be reinserted into the original data stream in a different
alignment that is determined by a multiframe signal from the RSYNC pin. In this mode, the receive elastic store can
be enabled or disabled. If the receive elastic store is enabled, then the backplane clock (RSYSCLK) can be either
1.544MHz or 2.048MHz. In the ESF framing mode, the ABCD signaling bits are output on RSIG in the lower nibble
of each channel. The RSIG data is updated once a multiframe (3ms) unless a freeze is in effect. In the D4 framing
mode, the AB signaling bits are output twice on RSIG in the lower nibble of each channel. Hence, bits 5 and 6
contain the same data as bits 7 and 8, respectively, in each channel. The RSIG data is updated once a multiframe
10.9.2.1 Receive Signaling Reinsertion at RSERO
In this mode, the user provides a multiframe sync at the RSYNC pin and the signaling data is reinserted based on
this alignment. In T1 mode, this results in two copies of the signaling data in the RSERO data stream, the original
signaling data and the realigned data. This is of little consequence in voice channels. Reinsertion can be avoided
in data channels since this feature is activated on a per-channel basis. In this mode, the elastic store must be
enabled; however, the backplane clock can be either 1.544MHz or 2.048MHz.
Signaling reinsertion can be enabled on a per-channel basis by setting the RSRCS bit high in the TR.PCPR
register. The channels that will have signaling reinserted are selected by writing to the TR.PCDR1–TR.PCDR3
registers for T1 mode and TR.PCDR1–TR.PCDR4 registers for E1 mode. In E1 mode, the user generally selects
all channels or none for reinsertion. In E1 mode, signaling reinsertion on all channels can be enabled with a single
bit, TR.SIGCR.7 (GRSRE). This bit allows the user to reinsert all signaling channels without having to program all
channels through the per-channel function.
10.9.2.2 Force Receive Signaling All Ones
In T1 mode, the user can, on a per-channel basis, force the robbed-bit signaling bit positions to a 1 by using the
per-channel register (Section 10.2). The user sets the BTCS bit in the TR.PCPR register. The channels that will be
forced to 1 are selected by writing to the TR.PCDR1–TR.PCDR3 registers.
10.9.2.3 Receive Signaling Freeze
The signaling data in the four multiframe signaling buffers is frozen in a known good state upon either a loss of
synchronization (OOF event), carrier loss, or frame slip. This action meets the requirements of BellCore TR–TSY–
000170 for signaling freezing. To allow this freeze action to occur, the RFE control bit (TR.SIGCR.4) should be set
high. The user can force a freeze by setting the RFF control bit (TR.SIGCR.3) high. The RSIGF output pin provides
a hardware indication that a freeze is in effect. The four-multiframe buffer provides a three-multiframe delay in the
signaling bits provided at the RSIG pin (and at the RSERO pin if receive signaling reinsertion is enabled). When
freezing is enabled (RFE = 1), the signaling data is held in the last-known good state until the corrupting error
condition subsides. When the error condition subsides, the signaling data is held in the old state for at least an
additional 9ms (or 4.5ms in D4 framing mode) before updating with new signaling data.
83 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-3. Simplified Diagram of Transmit Signaling Path
TRANSMIT
SIGNALING
REGISTERS
1
0
0
1
0
1
TSER
TSIG
T1/E1 DATA
STREAM
B7
SIGNALING
BUFFERS
TR.T1TCR1.4
PER-CHANNEL
CONTROL
PER-CHANNEL
CONTROL
TR.PCPR.3
TR.SSIE1 -
TR.SSIE4
ONLY APPLIES TO T1 MODE
10.9.3 Processor-Based Transmit Signaling
In processor-based mode, signaling data is loaded into the transmit signaling registers (TS1–TS16) by the host
interface. On multiframe boundaries, the contents of these registers are loaded into a shift register for placement in
the appropriate bit position in the outgoing data stream. The user can employ the transmit multiframe interrupt in
status register 4 (TR.SR4.4) to know when to update the signaling bits. The user need not update any transmit
signaling register for which there is no change-of-state for that register.
Each transmit signaling register contains the robbed-bit signaling (T1) or TS16 CAS signaling (E1) for two time
slots that are inserted into the outgoing stream, if enabled to do so through TR.T1TCR1.4 (T1 mode) or
TR.E1TCR1.6 (E1 mode). In T1 mode, only TS1–TS12 are used.
Signaling data can be sourced from the TR.TS registers on a per-channel basis by using the software signaling
insertion enable registers, TR.SSIE1–TRSSIE4.
10.9.3.1 T1 Mode
In T1 ESF framing mode, there are four signaling bits per channel (A, B, C, and D). TS1–TS12 contain a full
multiframe of signaling data. In T1 D4 framing mode, there are only two signaling bits per channel (A and B). In T1
D4 framing mode, the framer uses the C and D bit positions as the A and B bit positions for the next multiframe. In
D4 mode, two multiframes of signaling data can be loaded into TS1–TS12. The framer loads the contents of TS1–
TS12 into the outgoing shift register every other D4 multiframe. In D4 mode, the host should load new contents into
TS1–TS12 on every other multiframe boundary and no later than 120μs after the boundary. In T1 mode, only
registers TR.SSIE1–TR.SSIE3 are used since there are only 24 channels in a T1 frame.
84 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.9.3.2 E1 Mode
In E1 mode, TS16 carries the signaling information. This information can be in either CCS (common channel
signaling) or CAS (channel associated signaling) format. The 32 time slots are referenced by two different channel
number schemes in E1. In “Channel” numbering, TS0–TS31 are labeled channels 1 through 32. In “Phone
Channel” numbering, TS1–TS15 are labeled channel 1 through channel 15 and TS17–TS31 are labeled channel
15 through channel 30. In E1 CAS mode, the CAS signaling alignment/alarm byte can be sourced from the
transmit signaling registers along with the signaling data.
Table 10-9. Time Slot Numbering Schemes
0
1
1
2
1
2
3
2
3
4
3
4
5
4
5
6
5
6
7
6
7
8
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
TS
Channel
Phone
Channel
8
10.9.4 Hardware-Based Transmit Signaling
In hardware-based mode, signaling data is input through the TSIG pin. This signaling PCM stream is buffered and
inserted to the data stream being input at the TSERI pin.
Signaling data can be inserted on a per-channel basis by the transmit hardware-signaling channel-select (THSCS)
function. The user has the ability to control which channels are to have signaling data from the TSIG pin inserted
into them on a per-channel basis. See Section 10.2 for details on using this per-channel (THSCS) feature. The
signaling insertion capabilities of the framer are available whether the transmit-side elastic store is enabled or
disabled. If the elastic store is enabled, the backplane clock (TSYSCLK) can be either 1.544MHz or 2.048MHz.
Also, if the elastic is enabled in conjunction with transmit hardware signaling, CCR3.7 must be set = 0.
85 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.10 Per-Channel Idle Code Generation
Channel data can be replaced by an idle code on a per-channel basis in the transmit and receive directions. When
operated in the T1 mode, only the first 24 channels are used by the device, the remaining channels, CH25–CH32,
are not used.
The device contains a 64-byte idle code array accessed by the idle array address register (TR.IAAR) and the per-
channel idle code register (TR.PCICR). The contents of the array contain the idle codes to be substituted into the
appropriate transmit or receive channels. This substitution can be enabled and disabled on a per-channel basis by
the transmit-channel idle code-enable registers (TR.TCICE1–4) and receive-channel idle code-enable registers
(TR.RCICE1–4).
To program idle codes, first select a channel by writing to the TR.IAAR register. Then write the idle code to the
TR.PCICR register. For successive writes there is no need to load the TR.IAAR with the next consecutive address.
The TR.IAAR register automatically increments after a write to the TR.PCICR register. The auto increment feature
can be used for read operations as well. Bits 6 and 7 of the TR.IAAR register can be used to block write a common
idle code to all transmit or receive positions in the array with a single write to the TR.PCICR register. Bits 6 and 7
of the TR.IAAR register should not be used for read operations. TR.TCICE1–4 and TR.RCICE1–4 are used to
enable idle code replacement on a per-channel basis.
Table 10-10. Idle-Code Array Address Mapping
BITS 0 to 5 OF IAAR
MAPS TO CHANNEL
REGISTER
0
1
2
Transmit Channel 1
Transmit Channel 2
Transmit Channel 3
—
—
—
30
31
32
33
34
—
—
62
63
—
Transmit Channel 31
Transmit Channel 32
Receive Channel 1
Receive Channel 2
Receive Channel 3
—
—
Receive Channel 31
Receive Channel 32
86 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.10.1 Idle-Code Programming Examples
Example 1
Sets transmit channel 3 idle code to 7Eh.
Write TR.IAAR = 02h
;select channel 3 in the array
Write TR.PCICR = 7Eh ;set idle code to 7Eh
Example 2
Sets transmit channels 3, 4, 5, and 6 idle code to 7Eh and enables transmission of idle codes for those channels.
Write TR.IAAR = 02h
;select channel 3 in the array
Write TR.PCICR = 7Eh ;set channel 3 idle code to 7Eh
Write TR.PCICR = 7Eh ;set channel 4 idle code to 7Eh
Write TR.PCICR = 7Eh ;set channel 5 idle code to 7Eh
Write TR.PCICR = 7Eh ;set channel 6 idle code to 7Eh
Write TR.TCICE1 = 3Ch ;enable transmission of idle codes for channels 3,4,5, and 6
Example 3
Sets transmit channels 3, 4, 5, and 6 idle code to 7Eh, EEh, FFh, and 7Eh, respectively.
Write TR.IAAR = 02h
Write TR.PCICR = 7Eh
Write TR.PCICR = EEh
Write TR.PCICR = FFh
Write TR.PCICR = 7Eh
Example 4
Sets all transmit idle codes to 7Eh.
Write TR.IAAR = 4xh
Write TR.PCICR = 7Eh
Example 5
Sets all receive and transmit idle codes to 7Eh and enables idle code substitution in all E1 transmit and receive
channels.
Write TR.IAAR = Cxh
;enable block write to all transmit and receive positions in the array
Write TR.PCICR = 7Eh ;7Eh is idle code
Write TR.TCICE1 = FEh ;enable idle code substitution for transmit channels 2 through 8
;Although an idle code was programmed for channel 1 by the block write
;function above, enabling it for channel 1 would step on the frame
;alignment, alarms, and Sa bits
Write TR.TCICE2 = FFh ;enable idle code substitution for transmit channels 9 through 16
Write TR.TCICE3 = FEh ;enable idle code substitution for transmit channels 18 through 24
;Although an idle code was programmed for channel 17 by the block write
;function above, enabling it for channel 17 would step on the CAS frame
;alignment, and signaling information
Write TR.TCICE4 = FFh ;enable idle code substitution for transmit channels 25 through 32
Write TR.RCICE1 = FEh ;enable idle code substitution for receive channels 2 through 8
Write TR.RCICE2 = FFh ;enable idle code substitution for receive channels 9 through 16
Write TR.RCICE3 = FEh ;enable idle code substitution for receive channels 18 through 24
Write TR.RCICE4 = FFh ;enable idle code substitution for receive channels 25 through 32
The transmit-channel idle-code enable registers (TR.TCICE1/2/3/4) are used to determine which of the 24 T1 or 32
E1 channels from the backplane to the T1 or E1 line should be overwritten with the code placed in the per-channel
code array.
The receive-channel idle-code enable registers (TR.RCICE1/2/3/4) are used to determine which of the 24 T1 or 32
E1 channels from the backplane to the T1 or E1 line should be overwritten with the code placed in the per-channel
code array.
87 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.11 Channel Blocking Registers
The receive channel blocking registers (TR.RCBR1/TR.RCBR2/TR.RCBR3/TR.RCBR4) and the transmit channel
blocking registers (TR.TCBR1/TR.TCBR2/TR.TCBR3/TR.TCBR4) control RCHBLK and TCHBLK pins,
respectively. The RCHBLK and TCHBLK pins are user-programmable outputs that can be forced either high or low
during individual channels. These outputs can be used to block clocks to a USART or LAPD controller in ISDN-PRI
applications. When the appropriate bits are set to a 1, the RCHBLK and TCHBLK pins are held high during the
entire corresponding channel time. Channels 25 through 32 are ignored when the device is operated in the T1
mode.
10.12 Elastic Stores Operation
The device contains dual two-frame elastic stores, one for the receive direction and one for the transmit direction.
Both elastic stores are fully independent. The transmit and receive-side elastic stores can be enabled/disabled
independently of each other. Also, each elastic store can interface to either a 1.544MHz or 2.048MHz/4.096MHz/
8.192MHz/16.384MHz backplane without regard to the backplane rate the other elastic store is interfacing to.
The elastic stores have two main purposes. Firstly, they can be used for rate conversion. When the device is in the
T1 mode, the elastic stores can rate-convert the T1 data stream to a 2.048MHz backplane. In E1 mode, the elastic
store can rate-convert the E1 data stream to a 1.544MHz backplane. Secondly, they can be used to absorb the
differences in frequency and phase between the T1 or E1 data stream and an asynchronous (i.e., not locked)
backplane clock, which can be 1.544MHz or 2.048MHz. In this mode, the elastic stores manage the rate difference
and perform controlled slips, deleting or repeating frames of data in order to manage the difference between the
network and the backplane. The elastic stores can also be used to multiplex T1 or E1 data streams into higher
backplane rates.
10.12.1 Receive Elastic Store
See the TR.IOCR1 and TR.IOCR2 registers for information about clock and I/O configurations. If the receive-side
elastic store is enabled, then the user must provide either a 1.544MHz or 2.048MHz clock at the RSYSCLK pin.
The user has the option of either providing a frame/multiframe sync at the RSYNC pin or having the RSYNC pin
provide a pulse on frame/multiframe boundaries. If signaling reinsertion is enabled, signaling data in TS16 is
realigned to the multiframe sync input on RSYNC. Otherwise, a multiframe sync input on RSYNC is treated as a
simple frame boundary by the elastic store. The framer always indicates frame boundaries on the network side of
the elastic store by the RFSYNC output, whether the elastic store is enabled or not. Multiframe boundaries are
always indicated by the RMSYNC output. If the elastic store is enabled, then RMSYNC outputs the multiframe
boundary on the backplane side of the elastic store.
10.12.1.1T1 Mode
If the user selects to apply a 2.048MHz clock to the RSYSCLK pin, then the data output at RSERO is forced to all
1s every fourth channel and the F-bit is passed into the MSB of TS0. Hence, channels 1 (bits 1–7), 5, 9, 13, 17, 21,
25, and 29 [time slots 0 (bits 1–7), 4, 8, 12, 16, 20, 24, and 28] are forced to a 1. Also, in 2.048MHz applications,
the RCHBLK output is forced high during the same channels as the RSERO pin. This is useful in T1-to-E1
conversion applications. If the two-frame elastic buffer either fills or empties, a controlled slip occurs. If the buffer
empties, then a full frame of data is repeated at RSERO, and the TR.SR5.0 and TR.SR5.1 bits are set to a 1. If the
buffer fills, then a full frame of data is deleted, and the TR.SR5.0 and TR.SR5.2 bits are set to a 1.
10.12.1.2E1 Mode
If the elastic store is enabled, then either CAS or CRC4 multiframe boundaries are indicated through the RMSYNC
output. If the user selects to apply a 1.544MHz clock to the RSYSCLK pin, then every fourth channel of the
received E1 data is deleted and an F-bit position, which is forced to 1, is inserted. Hence, channels 1, 5, 9, 13, 17,
21, 25, and 29 (time slots 0, 4, 8, 12, 16, 20, 24, and 28) are deleted from the received E1 data stream. Also, in
1.544MHz applications, the RCHBLK output is not active in channels 25 through 32 (i.e., RCBR4 is not active). If
the two-frame elastic buffer either fills or empties, a controlled slip occurs. If the buffer empties, then a full frame of
data is repeated at RSERO, and the TR.SR5.0 and TR.SR5.1 bits are set to a 1. If the buffer fills, then a full frame
of data is deleted, and the TR.SR5.0 and TR.SR5.2 bits are set to a 1.
88 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.12.2 Transmit Elastic Store
See the TR.IOCR1 and TR.IOCR2 registers for information about clock and I/O configurations. The operation of
the transmit elastic store is very similar to the receive side. If the transmit-side elastic store is enabled, a 1.544MHz
or 2.048MHz clock can be applied to the TSYSCLK input. Controlled slips in the transmit elastic store are reported
in the TR.SR5.3 bit, and the direction of the slip is reported in the TR.SR5.4 and TR.SR5.5 bits. If hardware
signaling insertion is not enabled, TR.CCR3.7 should be set = 1.
10.12.2.1T1 Mode
If the user selects to apply a 2.048MHz clock to the TSYSCLK pin, then the data input at TSERI is ignored every
fourth channel. Therefore channels 1, 5, 9, 13, 17, 21, 25, and 29 (time slots 0, 4, 8, 12, 16, 20, 24, and 28) are
ignored. The user can supply frame or multiframe sync pulse to the TSSYNC input. Also, in 2.048MHz
applications, the TCHBLK output is forced high during the channels ignored by the framer.
10.12.2.2E1 Mode
A 1.544MHz or 2.048MHz clock can be applied to the TSYSCLK input. The user must supply a frame sync pulse or
a multiframe sync pulse to the TSSYNC input.
10.12.3 Elastic Stores Initialization
There are two elastic store initializations that can be used to improve performance in certain applications, elastic
store reset and elastic store align. Both of these involve the manipulation of the elastic store’s read and write
pointers and are useful primarily in synchronous applications (RSYSCLK/TSYSCLK are locked to RCLKO/TCLKT,
Table 10-11. Elastic Store Delay After Initialization
INITIALIZATION
REGISTER BIT
DELAY
Receive Elastic Store Reset
Transmit Elastic Store Reset
Receive Elastic Store Align
Transmit Elastic Store Align
TR.ESCR.2
TR.ESCR.6
TR.ESCR.3
TR.ESCR.7
8 Clocks < Delay < 1 Frame
1 Frame < Delay < 2 Frames
½ Frame < Delay < 1 ½ Frames
½ Frame < Delay < 1 ½ Frames
10.12.4 Minimum Delay Mode
Elastic store minimum delay mode can be used when the elastic store’s system clock is locked to its network clock
(i.e., RCLKO locked to RSYSCLK for the receive side and TCLKT locked to TSYSCLK for the transmit side).
TR.ESCR.5 and TR.ESCR.1 enable the transmit and receive elastic store minimum delay modes. When enabled,
the elastic stores are forced to a maximum depth of 32 bits instead of the normal two-frame depth. This feature is
useful primarily in applications that interface to a 2.048MHz bus. Certain restrictions apply when minimum delay
mode is used. In addition to the restriction mentioned above, RSYNC must be configured as an output when the
receive elastic store is in minimum delay mode; TSYNC must be configured as an output when transmit minimum
delay mode is enabled. In a typical application, RSYSCLK and TSYSCLK are locked to RCLKO, and RSYNC
(frame output mode) is connected to TSSYNC (frame input mode). All of the slip contention logic in the framer is
disabled (since slips cannot occur). On power-up, after the RSYSCLK and TSYSCLK signals have locked to their
respective network clock signals, the elastic store reset bits (TR.ESCR.2 and TR.ESCR.6) should be toggled from
a 0 to a 1 to ensure proper operation.
89 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.13 G.706 Intermediate CRC-4 Updating (E1 Mode Only)
The device can implement the G.706 CRC-4 recalculation at intermediate path points. When this mode is enabled,
the data stream presented at TSERI already has the FAS/NFAS, CRC multiframe alignment word, and CRC-4
checksum in time slot 0. The user can modify the Sa bit positions. This change in data content is used to modify
the CRC-4 checksum. This modification, however, does not corrupt any error information the original CRC-4
checksum may contain. In this mode of operation, TSYNC must be configured to multiframe mode. The data at
TSERI must be aligned to the TSYNC signal. If TSYNC is an input, then the user must assert TSYNC aligned at
the beginning of the multiframe relative to TSERI. If TSYNC is an output, the user must multiframe-align the data
presented to TSERI.
Figure 10-4. CRC-4 Recalculate Method
TPOSO/TNEGO
INSERT
NEW CRC-4
CODE
EXTRACT
OLD CRC-4
CODE
TSER
CRC-4
CALCULATOR
XOR
MODIFY
Sa BIT
+
POSITIONS
NEW Sa BIT
DATA
90 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.14 T1 Bit-Oriented Code (BOC) Controller
The transceiver contains a BOC generator on the transmit side and a BOC detector on the receive side. The BOC
function is available only in T1 mode.
10.14.1 Transmit BOC
Bits 0 to 5 in the TR.TFDL register contain the BOC message to be transmitted. Setting TR.BOCC.0 = 1 causes
the transmit BOC controller to immediately begin inserting the BOC sequence into the FDL bit position. The
transmit BOC controller automatically provides the abort sequence. BOC messages are transmitted as long as
TR.BOCC.0 is set.
10.14.1.1Transmit a BOC
1) Write 6-bit code into the TR.TFDL register.
2) Set the SBOC bit in TR.BOCC = 1.
10.14.2 Receive BOC
The receive BOC function is enabled by setting TR.BOCC.4 = 1. The TR.RFDL register now operates as the
receive BOC message and information register. The lower six bits of the TR.RFDL register (BOC message bits)
are preset to all 1s. When the BOC bits change state, the BOC change-of-state indicator, TR.SR8.0, alerts the
host. The host then reads the TR.RFDL register to get the BOC status and message. A change-of-state occurs
when either a new BOC code has been present for a time determined by the receive BOC filter bits RBF0 and
RBF1 in the TR.BOCC register, or a nonvalid code is being received.
10.14.2.1Receive a BOC
1) Set integration time through TR.BOCC.1 and TR.BOCC.2.
2) Enable the receive BOC function (TR.BOCC.4 = 1).
3) Enable interrupt (TR.IMR8.0 = 1).
4) Wait for interrupt to occur.
5) Read the TR.RFDL register.
6) If TR.SR2.7 = 1, then a valid BOC message was received. The lower six bits of the TR.RFDL register
comprise the message.
91 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.15 Additional (Sa) and International (Si) Bit Operation (E1 Only)
When operated in the E1 mode, the transceiver provides two methods for accessing the Sa and the Si bits. The
first method involves using the internal TR.RAF/TR.RNAF and TR.TAF/TR.TNAF registers (Section 10.15.1). The
second method, which is covered in Section 10.15.2, involves an expanded version of the first method.
10.15.1 Method 1: Internal Register Scheme Based on Double-Frame
On the receive side, the TR.RAF and TR.RNAF registers always report the data as it received in the Sa and Si bit
locations. The TR.RAF and TR.RNAF registers are updated on align-frame boundaries. The setting of the receive
align frame bit in Status Register 4 (TR.SR4.0) indicates that the contents of the TR.RAF and TR.RNAF have been
updated. The host can use the TR.SR4.0 bit to know when to read the TR.RAF and TR.RNAF registers. The host
has 250μs to retrieve the data before it is lost.
On the transmit side, data is sampled from the TR.TAF and TR.TNAF registers with the setting of the transmit align
frame bit in Status Register 4 (TR.SR4.3). The host can use the TR.SR4.3 bit to know when to update the TR.TAF
and TR.TNAF registers. It has 250μs to update the data or else the old data is retransmitted. If the TR.TAF and
TR.TNAF registers are only being used to source the align frame and nonalign frame-sync patterns, then
the host need only write once to these registers. Data in the Si bit position is overwritten if either the framer is
(1) programmed to source the Si bits from the TSERI pin, (2) in the CRC4 mode, or (3) has automatic E-bit
insertion enabled. Data in the Sa bit position is overwritten if any of the TR.E1TCR2.3 to TR.E1TCR2.7 bits are set
to 1.
10.15.2 Method 2: Internal Register Scheme Based on CRC4 Multiframe
The receive side contains a set of eight registers (TR.RSiAF, TR.RSiNAF, TR.RRA, and TR.RSa4–TR.RSa8) that
report the Si and Sa bits as they are received. These registers are updated with the setting of the receive CRC4
multiframe bit in Status Register 2 (TR.SR4.1). The host can use the TR.SR4.1 bit to know when to read these
registers. The user has 2ms to retrieve the data before it is lost. The MSB of each register is the first received. See
the following register descriptions for more details.
The transmit side also contains a set of eight registers (TR.TSiAF, TR.TSiNAF, TR.TRA, and TR.TSa4–TR.TSa8)
that, through the transmit Sa bit control register (TR.TSACR), can be programmed to insert Si and Sa data. Data is
sampled from these registers with the setting of the transmit multiframe bit in Status Register 2 (TR.SR4.4). The
host can use the TR.SR4.4 bit to know when to update these registers. It has 2ms to update the data or else the
old data is retransmitted. The MSB of each register is the first bit transmitted. See the register descriptions for
more details.
92 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.16 Additional HDLC Controllers in T1/E1/J1 Transceiver
This device has two enhanced HDLC controllers, HDLC #1 and HDLC #2. Each controller is configurable for use
with time slots, Sa4 to Sa8 bits (E1 mode), or the FDL (T1 mode). Each HDLC controller has 128-byte buffers in
the transmit and receive paths. When used with time slots, the user can select any time slot or multiple time slots,
contiguous or noncontiguous, as well as any specific bits within the time slot(s) to assign to the HDLC controllers.
The user must not map both transmit HDLC controllers to the same Sa bits, time slots or, in T1 mode, map both
controllers to the FDL. HDLC #1 and HDLC #2 are identical in operation and therefore the following operational
description refers only to a singular controller.
The HDLC controller performs the entire necessary overhead for generating and receiving performance report
messages (PRMs) as described in ANSI T1.403 and the messages as described in AT&T TR54016. The HDLC
controller automatically generates and detects flags, generates and checks the CRC check sum, generates and
detects abort sequences, stuffs and destuffs zeros, and byte aligns to the data stream. The 128-byte buffers in the
HDLC controller are large enough to allow a full PRM to be received or transmitted without host intervention.
The HDLC registers are divided into four groups: control/configuration, status/information, mapping, and FIFOs.
Table 10-12 lists these registers by group.
10.16.1 HDLC Configuration
The TR.HxTC and TR.HxRC registers perform the basic configuration of the HDLC controllers. Operating features
such as CRC generation, zero stuffer, transmit and receive HDLC mapping options, and idle flags are selected
here. These registers also reset the HDLC controllers.
93 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 10-12. HDLC Controller Registers
REGISTER
FUNCTION
CONTROL AND CONFIGURATION
General control over the transmit HDLC controllers
TR.H1TC, HDLC #1 Transmit Control Register
TR.H2TC, HDLC #2 Transmit Control Register
TR.H1RC, HDLC #1 Receive Control Register
TR.H2RC, HDLC #2 Receive Control Register
TR.H1FC, HDLC #1 FIFO Control Register
TR.H2FC, HDLC #2 FIFO Control Register
General control over the receive HDLC controllers
Sets high watermark for receiver and low
watermark for transmitter
STATUS AND INFORMATION
Key status information for both transmit and
receive directions
TR.SR6, HDLC #1 Status Register
TR.SR7, HDLC #2 Status Register
Selects which bits in the status registers (SR7 and
SR8) cause interrupts
Information about HDLC controller
TR.IMR6, HDLC #1 Interrupt Mask Register
TR.IMR7, HDLC #2 Interrupt Mask Register
TR.INFO4, HDLC #1 and #2 Information Register
TR.INFO5, HDLC #1 Information Register
TR.INFO6, HDLC #2 Information Register
Indicates the number of bytes that can be read
from the receive FIFO
Indicates the number of bytes that can be written to
the transmit FIFO
TR.H1RPBA, HDLC #1 Receive Packet Bytes Available
TR.H2RPBA, HDLC #2 Receive Packet Bytes Available
TR.H1TFBA, HDLC #1 Transmit FIFO Buffer Available
TR.H2TFBA, HDLC #2 Transmit FIFO Buffer Available
MAPPING
Selects which channels are mapped to the receive
HDLC controller
TR.H1RCS1, TR.H1RCS2, TR.H1RCS3, TR.H1RCS4,
HDLC #1 Receive Channel Select Registers
TR.H2RCS1, TR.H2RCS2, TR.H2RCS3, TR.H2RCS4,
HDLC #2 Receive Channel Select Registers
Selects which bits in a channel are used or which
Sa bits are used by the receive HDLC controller
Selects which channels are mapped to the transmit
HDLC controller
TR.H1RTSBS, HDLC #1 Receive TS/Sa Bit Select
TR.H2RTSBS, HDLC #2 Receive TS/Sa Bit Select
TR.H1TCS1, TR.H1TCS2, TR.H1TCS3, TR.H1TCS4,
HDLC #1 Transmit Channel Select Registers
TR.H2TCS1, TR.H2TCS2, TR.H2TCS3, TR.H2TCS4,
HDLC #2 Transmit Channel Select Registers
Selects which bits in a channel are used or which
Sa bits are used by the transmit HDLC controller
TR.H1TTSBS, HDLC # 1 Transmit TS/Sa Bit Select
TR.H2TTSBS, HDLC # 2 Transmit TS/Sa Bit Select
FIFOs
Access to 128-byte receive FIFO
Access to 128-byte transmit FIFO
TR.H1RF, HDLC #1 Receive FIFO Register
TR.H2RF, HDLC #1 Receive FIFO Register
TR.H1TF, HDLC #1 Transmit FIFO Register
TR.H2TF, HDLC #2 Transmit FIFO Register
94 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.16.2
FIFO Control
The FIFO control register (TR.HxFC) controls and sets the watermarks for the transmit and receive FIFOs. Bits 3,
4, and 5 set the transmit low watermark and the lower 3 bits set the receive high watermark.
When the transmit FIFO empties below the low watermark, the TLWM bit in the appropriate HDLC status register
TR.SR6 or TR.SR7 is set. TLWM is a real-time bit and remains set as long as the transmit FIFO’s read pointer is
below the watermark. If enabled, this condition can also cause an interrupt through the INT pin.
When the receive FIFO fills above the high watermark, the RHWM bit in the appropriate HDLC status register is
set. RHWM is a real-time bit and remains set as long as the receive FIFO’s write pointer is above the watermark. If
enabled, this condition can also cause an interrupt through the INT pin.
10.16.3 HDLC Mapping
The HDLC controllers must be assigned a space in the T1/E1 bandwidth in which they transmit and receive data.
The controllers can be mapped to either the FDL (T1), Sa bits (E1), or to channels. If mapped to channels, then
any channel or combination of channels, contiguous or not, can be assigned to an HDLC controller. When
assigned to a channel(s), any combination of bits within the channel(s) can be avoided.
The TR.HxRCS1 – TR.HxRCS4 registers are used to assign the receive controllers to channels 1–24 (T1) or
1–32 (E1) according to the following table:
REGISTER
CHANNELS
TR.HxRCS1
TR.HxRCS2
TR.HxRCS3
TR.HxRCS4
1–8
9–16
17–24
25–32
The TR.HxTCS1 – TR.HxTCS4 registers are used to assign the transmit controllers to channels 1–24 (T1) or
1–32 (E1) according to the following table.
REGISTER
CHANNELS
TR.HxTCS1
TR.HxTCS2
TR.HxTCS3
TR.HxTCS4
1–8
9–16
17–24
25–32
95 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.16.4 FIFO Information
The transmit FIFO buffer-available register indicates the number of bytes that can be written into the transmit FIFO.
The count form this register informs the host as to how many bytes can be written into the transmit FIFO without
overflowing the buffer.
10.16.5
Receive Packet-Bytes Available
The lower 7 bits of the receive packet-bytes available register indicates the number of bytes (0 through 127) that
can be read from the receive FIFO. The value indicated by this register (lower seven bits) informs the host as to
how many bytes can be read from the receive FIFO without going past the end of a message. This value refers to
one of four possibilities: the first part of a packet, the continuation of a packet, the last part of a packet, or a
complete packet. After reading the number of bytes indicated by this register, the host then checks the HDLC
information register for detailed message status.
If the value in the TR.HxRPBA register refers to the beginning portion of a message or continuation of a message,
then the MSB of the TR.HxRPBA register returns a value of 1. This indicates that the host can safely read the
number of bytes returned by the lower seven bits of the TR.HxRPBA register, but there is no need to check the
information register since the packet has not yet terminated (successfully or otherwise).
10.16.5.1Receive HDLC Code Example
The following is an example of a receive HDLC routine:
1) Reset receive HDLC controller.
2) Set HDLC mode, mapping, and high watermark.
3) Start new message buffer.
4) Enable RPE and RHWM interrupts.
5) Wait for interrupt.
6) Disable RPE and RHWM interrupts.
7) Read TR.HxRPBA register. N = TR.HxRPBA (lower 7 bits are byte count, MSB is status).
8) Read (N and 7Fh) bytes from receive FIFO and store in message buffer.
9) Read TR.INFO5 register.
10) If PS2, PS1, PS0 = 000, then go to Step 4.
11) If PS2, PS1, PS0 = 001, then packet terminated OK, save present message buffer.
12) If PS2, PS1, PS0 = 010, then packet terminated with CRC error.
13) If PS2, PS1, PS0 = 011, then packet aborted.
14) If PS2, PS1, PS0 = 100, then FIFO overflowed.
15) Go to Step 3.
96 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.17 Legacy FDL Support (T1 Mode)
10.17.1 Overview
To provide backward compatibility to the older DS21x52 T1 device, the transceiver maintains the circuitry that
existed in the previous generation of the T1 framer. In new applications, it is recommended that the HDLC
10.17.2 Receive Section
In the receive section, the recovered FDL bits or Fs bits are shifted bit-by-bit into the receive FDL register
(TR.RFDL). Because the TR.RFDL is 8 bits in length, it fills up every 2ms (8 x 250μs). The framer signals an
external microcontroller that the buffer has filled through the TR.SR8.3 bit. If enabled through TR.IMR8.3, the INT
pin toggles low, indicating that the buffer has filled and needs to be read. The user has 2ms to read this data
before it is lost. If the byte in the TR.RFDL matches either of the bytes programmed into the TR.RFDLM1 or
TR.RFDLM2 registers, then the TR.SR8.1 bit is set to a 1 and the INT pin toggles low if enabled through
TR.IMR8.1. This feature allows an external microcontroller to ignore the FDL or Fs pattern until an important event
occurs.
The framer also contains a zero destuffer, which is controlled through the TR.T1RCR2.3 bit. In both ANSI T1.403
and TR54016, communications on the FDL follows a subset of an LAPD protocol. The LAPD protocol states that
no more than five 1s should be transmitted in a row so that the data does not resemble an opening or closing flag
(01111110) or an abort signal (11111111). If enabled through TR.T1RCR2.3, the device automatically looks for five
1s in a row, followed by a 0. If it finds such a pattern, it automatically removes the zero. If the zero destuffer sees
six or more 1s in a row followed by a 0, the 0 is not removed. The TR.T1RCR2.3 bit should always be set to a 1
when the device is extracting the FDL. Refer to Application Note 335: DS2141A, DS2151 Controlling the FDL for
information about using the device in FDL applications in this legacy support mode.
97 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.17.3 Transmit Section
The transmit section shifts out into the T1 data stream either the FDL (in the ESF framing mode) or the Fs bits (in
the D4 framing mode) contained in the transmit FDL register (TR.TFDL). When a new value is written to TR.TFDL,
it is multiplexed serially (LSB first) into the proper position in the outgoing T1 data stream. After the full 8 bits have
been shifted out, the framer signals the host microcontroller by setting the TR.SR8.2 bit to a 1 that the buffer is
empty and that more data is needed. The INT also toggles low if enabled through TR.IMR8.2. The user has 2ms to
update TR.TFDL with a new value. If TR.TFDL is not updated, the old value in TR.TFDL is transmitted once again.
The framer also contains a zero stuffer that is controlled through the TR.T1TCR2.5 bit. In both ANSI T1.403 and
TR54016, communications on the FDL follows a subset of an LAPD protocol. The LAPD protocol states that no
more than five 1s should be transmitted in a row so that the data does not resemble an opening or closing flag
(01111110) or an abort signal (11111111). If enabled through TR.T1TCR2.5, the framer automatically looks for five
1s in a row. If it finds such a pattern, it automatically inserts a 0 after the five 1s. The TR.T1TCR2.5 bit should
always be set to a 1 when the framer is inserting the FDL.
10.18 D4/SLC-96 Operation
In the D4 framing mode, the framer uses the TR.TFDL register to insert the Fs framing pattern. To allow the device
to properly insert the Fs framing pattern, the TR.TFDL register at address C1h must be programmed to 1Ch and
the following bits must be programmed as shown:
TR.T1TCR1.2 = 0 (source Fs data from the TR.TFDL register)
TR.T1TCR2.6 = 1 (allow the TR.TFDL register to load on multiframe boundaries)
Since the SLC-96 message fields share the Fs-bit position, the user can access these message fields through the
TR.TFDL and TR.RFDL registers. Refer to Application Note 345: DS2141A, DS2151, DS2152 SLC-96 for a
detailed description about implementing an SLC-96 function.
98 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.19 Programmable In-Band Loop Code Generation and Detection
The transceiver has the ability to generate and detect a repeating bit pattern from one to eight bits or 16 bits in
length. This function is available only in T1 mode. To transmit a pattern, the user loads the pattern into the
transmit code-definition registers (TR.TCD1 and TR.TCD2) and selects the proper length of the pattern by setting
the TC0 and TC1 bits in the in-band code control (TR.IBCC) register. When generating a 1-, 2-, 4-, 8-, or 16-bit
pattern, both transmit code-definition registers must be filled with the proper code. Generation of a 3-, 5-, 6-, and 7-
bit pattern only requires TR.TCD1 to be filled. Once this is accomplished, the pattern is transmitted as long as the
TLOOP control bit (TR.T1CCR1.0) is enabled. Normally (unless the transmit formatter is programmed to not insert
the F-bit position) the framer overwrites the repeating pattern once every 193 bits to send the F-bit position.
For example, to transmit the standard “loop-up” code for CSUs, which is a repeating pattern of ...10000100001... ,
set TR.TCD1 = 80h, TR.IBCC = 0, and TR.T1CCR1.0 = 1.
The framer has three programmable pattern detectors. Typically two of the detectors are used for “loop-up” and
“loop-down” code detection. The user programs the codes to be detected in the receive up-code definition
(TR.RUPCD1 and TR.RUPCD2) registers and the receive down-code definition (TR.RDNCD1 and TR.RDNCD2)
registers, and the length of each pattern is selected through the TR.IBCC register. There is a third detector (spare)
that is defined and controlled through the TR.RSCD1/ TR.RSCD2 and TR.RSCC registers. When detecting a 16-bit
pattern, both receive code-definition registers are used together to form a 16-bit register. For 8-bit patterns, both
receive code-definition registers are filled with the same value. Detection of a 1-, 2-, 3-, 4-, 5-, 6-, and 7-bit pattern
only requires the first receive code-definition register to be filled. The framer detects repeating pattern codes in
both framed and unframed circumstances with bit error rates as high as 10E-2. The detectors are capable of
handling both F-bit inserted and F-bit overwrite patterns. Writing the least significant byte of the receive code-
definition register resets the integration period for that detector. The code detector has a nominal integration period
of 36ms. Hence, after about 36ms of receiving a valid code, the proper status bit (LUP at TR.SR3.5, LDN at
TR.SR3.6, and LSPARE at TR.SR3.7) is set to a 1. Normally codes are sent for a period of five seconds. It is
recommended that the software poll the framer every 50ms to 1000ms until five seconds has elapsed to ensure the
code is continuously present.
99 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.20 Line Interface Unit (LIU)
The LIU contains three sections: the receiver that handles clock and data recovery, the transmitter that
waveshapes and drives the T1 line, and the jitter attenuator. These three sections are controlled by the line
interface control registers (LIC1–LIC4), which are described in the following sections. The LIU has its own T1/E1
mode-select bit and can operate independently of the framer function.
The transceiver can switch between T1 or E1 networks without changing external components on the transmit or
receive side. Figure 10-7 shows a network connection using minimal components. In this configuration, the
transceiver can connect to T1, J1, or E1 (75Ω or 120Ω) without component changes. The receiver can adjust the
120Ω termination to 100Ω or 75Ω. The transmitter can adjust its output impedance to provide high return-loss
characteristics for 120Ω, 100Ω, and 75Ω lines. Other components can be added to this configuration to meet
10.20.1 LIU Operation
The analog AMI/HDB3 waveform off the E1 line or the AMI/B8ZS waveform off of the T1 line is transformer-
coupled into the RTIP and RRING pins of the device. The user has the option to use internal termination, software
selectable for 75Ω/100Ω/120Ω applications, or external termination. The LIU recovers clock and data from the
analog signal and passes it through the jitter-attenuation mux outputting the received line clock at RDCLKO and
bipolar or NRZ data at RPOSO and RNEGO. The transceiver contains an active filter that reconstructs the analog-
received signal for the nonlinear losses that occur in transmission. The receive circuitry also is configurable for
various monitor applications. The device has a usable receive sensitivity of 0dB to -43dB for E1 and 0dB to -36dB
for T1, which allow the device to operate on 0.63mm (22AWG) cables up to 2.5km (E1) and 6k feet (T1) in length.
Data input at TPOSI and TNEGI is sent through the jitter-attenuation mux to the waveshaping circuitry and line
driver. The transceiver drives the E1 or T1 line from the TTIP and TRING pins through a coupling transformer. The
line driver can handle both CEPT 30/ISDN-PRI lines for E1 and long-haul (CSU) or short-haul (DSX-1) lines for T1.
10.20.2 Receiver
The receiver contains a digital clock recovery system. The device couples to the receive E1 or T1 twisted pair (or
coaxial cable in 75Ω E1 applications) through a 1:1 transformer. See Table 10-13 for transformer details. The
device has the option of using software-selectable termination requiring only a single fixed pair of termination
resistors.
The transceiver’s LIU is designed to be fully software selectable for E1 and T1, requiring no change to any external
resistors for the receive side. The receive side allows the user to configure the transceiver for 75Ω, 100Ω, or 120Ω
receive termination by setting the RT1 (TR.LIC4.1) and RT0 (TR.LIC4.0) bits. When using the internal termination
feature, the resistors labeled R in Figure 10-7 should be 60Ω each. If external termination is used, RT1 and RT0
should be set to 0 and the resistors labeled R in Figure 10-7 should be 37.5Ω, 50Ω, or 60Ω each, depending on
the line impedance.
There are two ranges of user-selectable receive sensitivity for T1 and E1. The EGL bit of TR.LIC1 (TR.LIC1.4)
selects the full or limited sensitivity. The resultant E1 or T1 clock derived from MCLK is multiplied by 16 through an
internal PLL and fed to the clock recovery system. The clock recovery system uses the clock from the PLL circuit to
form a 16-times over-sampler that is used to recover the clock and data. This over-sampling technique offers
Normally, the clock that is output at the RCLKO pin is the recovered clock from the E1 AMI/HDB3 or T1 AMI/B8ZS
waveform presented at the RTIP and RRING inputs. If the jitter attenuator is placed in the receive path (as is the
case in most applications), the jitter attenuator restores the RCLKO to an approximate 50% duty cycle. If the jitter
attenuator is either placed in the transmit path or is disabled, the RCLKO output can exhibit slightly shorter high
cycles of the clock. This is because of the highly over-sampled digital-clock recovery circuitry. See the Receive AC
Timing Characteristics in Section 13.9 for more details. When no signal is present at RTIP and RRING, a receive
carrier loss (RCL) condition occurs and the RCLKO is derived from the JACLK source.
100 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.20.2.1Receive Level Indicator and Threshold Interrupt
The device reports the signal strength at RTIP and RRING in 2.5dB increments through RL3–RL0 located in
Information Register 2 (TR.INFO2). This feature is helpful when trouble-shooting line-performance problems. The
device can initiate an interrupt whenever the input falls below a certain level through the input-level under-threshold
indicator (TR.SR1.7). Using the RLT0–RLT4 bits of the TR.CCR4 register, the user can set a threshold in 2.5dB
increments. The TR.SR1.7 bit is set whenever the input level at RTIP and RRING falls below the threshold set by
the value in RLT0–RLT4. The level must remain below the programmed threshold for approximately 50ms for this
bit to be set. The accuracy of the receive level indication is ±1 LSB (2.5dB) from 25°C to 85°C and ±2 LSBs (5dB)
from –40°C to 25°C.
10.20.2.2Receive G.703 Synchronization Signal (E1 Mode)
The transceiver is capable of receiving a 2.048MHz square-wave synchronization clock as specified in Section 13
of ITU G.703, October 1998. In order to use the device in this mode, set the receive synchronization clock enable
(TR.LIC3.2) = 1.
10.20.2.3Monitor Mode
Monitor applications in both E1 and T1 require various flat gain settings for the receive-side circuitry. The device
can be programmed to support these applications through the monitor mode control bits MM1 and MM0 in the
Figure 10-5. Typical Monitor Application
PRIMARY
T1/E1 LINE
Rm
T1/E1 TERMINATING
DEVICE
Rm
X
F
M
R
T1/E1
XCVR
Rt
MONITOR
PORT JACK
SECONDARY T1/E1
TERMINATING
DEVICE
101 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.20.3 Transmitter
The transceiver uses a phase-lock loop along with a precision digital-to-analog converter (DAC) to create the
waveforms that are transmitted onto the E1 or T1 line. The waveforms created by the device meet the latest ETSI,
ITU-T, ANSI, and AT&T specifications. The user selects which waveform is generated by setting the ETS bit
(TR.LIC2.7) for E1 or T1 operation, then programming the L2/L1/L0 bits in register TR.LIC1 for the appropriate
application.
A 2.048MHz or 1.544MHz clock is required at TDCLKI for transmitting data presented at TPOSI and TNEGI.
Normally these pins are connected to TCLKO, TPOSO, and TNEGO. However, the LIU can operate in an
independent fashion. ITU specification G.703 requires an accuracy of ±50ppm for both T1 and E1. TR62411 and
ANSI specifications require an accuracy of ±32ppm for T1 interfaces. The clock can be sourced internally from
RCLKO or JACLK. See TR.LIC2.3, TR.LIC4.4, and TR.LIC4.5 for details. Because of the nature of the transmitter’s
design, very little jitter (less than 0.005UIP-P broadband from 10Hz to 100kHz) is added to the jitter present on
TCLKT. Also, the waveforms created are independent of the duty cycle of TCLKT. The transmitter in the device
couples to the E1 or T1 transmit twisted pair (or coaxial cable in some E1 applications) through a 1:2 step-up
transformer. For the device to create the proper waveforms, the transformer used must meet the specifications
The transmit line drive has two modes of operation: fixed gain or automatic gain. In the fixed gain mode, the
transmitter outputs a fixed current into the network load to achieve a nominal pulse amplitude. In the automatic
gain mode, the transmitter adjusts its output level to compensate for slight variances in the network load. See the
Transmit Line Build-Out Control (TR.TLBC) register for details.
10.20.3.1Transmit Short-Circuit Detector/Limiter
The device has an automatic short-circuit limiter that limits the source current to 50mA (RMS) into a 1Ω load. This
feature can be disabled by setting the SCLD bit (TR.LIC2.1) = 1. TCLE (TR.INFO2.5) provides a real-time
indication of when the current limiter is activated. If the current limiter is disabled, TCLE indicates that a short-
circuit condition exists. Status Register TR.SR1.2 provides a latched version of the information, which can be used
to activate an interrupt when enabled by the TR.IMR1 register. The TPD bit (TR.LIC1.0) powers down the transmit
line driver and three-states the TTIP and TRING pins.
10.20.3.2Transmit Open-Circuit Detector
The device can also detect when the TTIP or TRING outputs are open circuited. TOCD (TR.INFO2.4) provides a
real-time indication of when an open circuit is detected. TR.SR1 provides a latched version of the information
(TR.SR1.1), which can be used to activate an interrupt when enabled by the TR.IMR1 register.
10.20.3.3Transmit BPV Error Insertion
When IBPV (TR.LIC2.5) is transitioned from a 0 to a 1, the device waits for the next occurrence of three
consecutive 1s to insert a BPV. IBPV must be cleared and set again for another BPV error insertion.
10.20.3.4Transmit G.703 Synchronization Signal (E1 Mode)
The transceiver can transmit the 2.048MHz square-wave synchronization clock as specified in Section 13 of ITU
G.703, October 1998. In order to transmit the 2.048MHz clock, when in E1 mode, set the transmit synchronization
clock enable (TR.LIC3.1) = 1.
102 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.21 MCLK Prescaler
A 16.384MHz, 8.192MHz, 4.096MHz, 2.048MHz, or 1.544MHz clock must be applied at MCLK. ITU specification
G.703 requires an accuracy of ±50ppm for both T1 and E1. TR62411 and ANSI specifications require an accuracy
of ±32ppm for T1 interfaces. A prescaler divides the 16MHz, 8MHz, or 4MHz clock down to 2.048MHz. There is an
on-board PLL for the jitter attenuator, which converts the 2.048MHz clock to a 1.544MHz rate for T1 applications.
Setting JAMUX (TR.LIC2.3) to a logic 0 bypasses this PLL.
10.22 Jitter Attenuator
The device contains an on-board jitter attenuator that can be set to a depth of either 32 or 128 bits through the
JABDS bit (TR.LIC1.2). The 128-bit mode is used in applications where large excursions of wander are expected.
The 32-bit mode is used in delay-sensitive applications. The characteristics of the attenuation are shown in
Figure 10-12. The jitter attenuator can be placed in either the receive path or the transmit path by appropriately
setting or clearing the JAS bit (TR.LIC1.3). Setting the DJA bit (TR.LIC1.1) disables (in effect, removes) the jitter
attenuator. On-board circuitry adjusts either the recovered clock from the clock/data recovery block or the clock
applied at the TCLKT pin to create a smooth jitter-free clock that is used to clock data out of the jitter attenuator
FIFO. It is acceptable to provide a gapped/bursty clock at the TCLKT pin if the jitter attenuator is placed on the
transmit side. If the incoming jitter exceeds either 120UIP-P (buffer depth is 128 bits) or 28UIP-P (buffer depth is 32
bits), then the transceiver divides the internal nominal 32.768MHz (E1) or 24.704MHz (T1) clock by either 15 or 17
instead of the normal 16 to keep the buffer from overflowing. When the device divides by either 15 or 17, it also
sets the jitter attenuator limit trip (JALT) bit in Status Register 1 (TR.SR1.4).
10.23 CMI (Code Mark Inversion) Option
The device provides a CMI interface for connection to optical transports. This interface is a unipolar 1T2B signal
type. Ones are encoded as either a logical 1 or 0 level for the full duration of the clock period. Zeros are encoded
as a 0-to-1 transition at the middle of the clock period.
Figure 10-6. CMI Coding
CLOCK
1
1
0
1
0
0
1
DATA
CMI
Transmit and receive CMI are enabled through TR.LIC4.7. When this register bit is set, the TTIP pin outputs CMI-
coded data at normal levels. This signal can be used to directly drive an optical interface. When CMI is enabled,
the user can also use HDB3/B8ZS coding. When this register bit is set, the RTIP pin becomes a unipolar CMI
input. The CMI signal is processed to extract and align the clock with data.
103 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.24 Recommended Circuits
Figure 10-7. Basic Interface
VDD
DS33R11
2:1
0.1μF 0.01μF
TTIP
DVDD
TRANSMIT
LINE
C
DVSS
0.1μF 10μF
TRING
RTIP
TVDD
TVSS
+
1:1
0.1μF 10μF
RECEIVE
LINE
RVDD
RVSS
+
RRING
R
R
0.1μF
NOTE 1: ALL RESISTOR VALUES ARE ±1%.
NOTE 2: RESISTORS R SHOULD BE SET TO 60Ω EACH IF THE INTERNAL RECEIVE-SIDE TERMINATION FEATURE IS ENABLED.
WHEN THIS FEATURE IS DISABLED, R = 37.5Ω FOR 75Ω COAXIAL E1 LINES, 60Ω FOR 120Ω TWISTED-PAIR E1 LINES, OR 50Ω
FOR 100Ω TWISTED-PAIR T1 LINES.
NOTE 3: C = 1μF CERAMIC.
Refer to Application Note 324: T1/E1 Network Interface Design for more information on protected interfaces.
Table 10-13. Transformer Specifications
SPECIFICATION
RECOMMENDED VALUE
Turns Ratio 3.3V Applications
Primary Inductance
1:1 (receive) and 1:2 (transmit) ±2%
600μH (min)
Leakage Inductance
1.0μH (max)
Intertwining Capacitance
Transmit Transformer DC Resistance
Primary (Device Side)
Secondary
40pF (max)
1.0Ω (max)
2.0Ω (max)
Receive Transformer DC Resistance
Primary (Device Side)
Secondary
1.2Ω (max)
1.2Ω (max)
104 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-8. E1 Transmit Pulse Template
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
269ns
G.703
TEMPLATE
194ns
219ns
-0.1
-0.2
-250
-200
-150
-100
-50
0
50
100
150
200
250
TIME (ns)
Figure 10-9. T1 Transmit Pulse Template
1.2
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
MAXIMUM CURVE
UI Time Amp.
MINIMUM CURVE
UI Time Amp.
-0.77 -500 0.05
-0.39 -255 0.05
-0.27 -175 0.80
-0.27 -175 1.15
-0.77 -500 -0.05
-0.23 -150 -0.05
-0.23 -150 0.50
-0.15 -100 0.95
-0.12 -75
0.00
0.27 175
0.35 225
0.93 600
1.16 750
1.15
1.05
1.05
-0.07
0.05
0.05
0.00
0
0.95
0
0.15 100
0.23 150
0.23 150
0.46 300
0.66 430
0.93 600
1.16 750
0.90
0.50
-0.45
-0.45
-0.20
-0.05
-0.05
-0.1
T1.102/87, T1.403,
CB 119 (OCT. 79), AND
-0.2
I.431 TEMPLATE
-0.3
-0.4
-0.5
-500 -400 -300 -200 -100
0
100
200
300
400
500
600
700
TIME (ns)
105 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-10. Jitter Tolerance
1k
DEVICE
TOLERANCE
100
TR 62411 (DEC. 90)
10
1
ITU-T G.823
0.1
1
10
100
1k
10k
100k
FREQUENCY (Hz)
Figure 10-11. Jitter Tolerance (E1 Mode)
1k
DEVICE
TOLERANCE
100
40
10
1
1.5
MINIMUM TOLERANCE
LEVEL AS PER
ITU G.823
0.2
0.1
2.4k
20
18k
1
10
100
1k
10k
100k
FREQUENCY (Hz)
106 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-12. Jitter Attenuation (T1 Mode)
0dB
-20dB
-40dB
-60dB
TR 62411 (Dec. 90)
Prohibited Area
T1 MODE
100
1
10
1K
10K
100K
FREQUENCY (Hz)
Figure 10-13. Jitter Attenuation (E1 Mode)
0
ITU G.7XX
TBR12
Prohibited Area
Prohibited
Area
-20
-40
-60
E1 MODE
1
10
100
1k
10k
100k
FREQUENCY (Hz)
107 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-14. Optional Crystal Connections
XTALD
MCLK
1.544MHz/2.048MHz
C1
C2
NOTE: C1 AND C2 SHOULD BE 5pF LOWER THAN TWO TIMES THE NOMINAL LOADING CAPACITANCE
OF THE CRYSTAL TO ADJUST FOR THE INPUT CAPACITANCE OF THE DEVICE.
10.25 T1/E1/J1 TRANSCEIVER BERT FUNCTION
The BERT block can generate and detect pseudorandom and repeating bit patterns. It is used to test and stress
data communication links, and it is capable of generating and detecting the following patterns:
ꢀ
ꢀ
ꢀ
ꢀ
The pseudorandom patterns 2E7, 2E11, 2E15, and QRSS
A repetitive pattern from 1 to 32 bits in length
Alternating (16-bit) words that flip every 1 to 256 words
Daly pattern
The BERT receiver has a 32-bit bit counter and a 24-bit error counter. The BERT receiver reports three events: a
change in receive synchronizer status, a bit error being detected, and if either the bit counter or the error counter
overflows. Each of these events can be masked within the BERT function through the BERT control register 1
(TR.BC1). If the software detects that the BERT has reported an event, then the software must read the BERT
information register (BIR) to determine which event(s) has occurred. To activate the BERT block, the host must
configure the BERT mux through the TR.BIC register.
10.25.1 BERT Status
TR.SR9 contains the status information on the BERT function. The host can be alerted through this register when
there is a BERT change-of-state. A major change-of-state is defined as either a change in the receive
synchronization (i.e., the BERT has gone into or out of receive synchronization), a bit error has been detected, or
an overflow has occurred in either the bit counter or the error counter. The host must read status register 9
(TR.SR9) to determine the change-of-state.
10.25.2 BERT Mapping
The BERT function can be assigned to the network direction or backplane direction through the direction control bit
in the BIC register (TR.BIC.1). See Figure 10-15 and Figure 10-16. The BERT also can be assigned on a per-
channel basis. The BERT transmit control selector (BTCS) and BERT receive control selector (BRCS) bits of the
per-channel pointer register (TR.PCPR) are used to map the BERT function into time slots of the transmit and
receive data streams. In T1 mode, the user can enable mapping into the F-bit position for the transmit and receive
directions through the RFUS and TFUS bits in the BERT interface control (TR.BIC) register.
108 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-15. Simplified Diagram of BERT in Network Direction
TO RECEIVE
SYSTEM
BACKPLANE
INTERFACE
FROM RECEIVE
FRAMER
PER-CHANNEL AND
F-BIT (T1 MODE)
MAPPING
BERT
BERT
RECEIVER TRANSMITTER
1
0
TO TRANSMIT
FRAMER
FROM TRANSMIT
SYSTEM
BACKPLANE
INTERFACE
Figure 10-16. Simplified Diagram of BERT in Backplane Direction
TO RECEIVE
SYSTEM
FROM RECEIVE
0
FRAMER
BACKPLANE
INTERFACE
1
PER-CHANNEL AND
F-BIT (T1 MODE)
MAPPING
BERT
BERT
RECEIVER
TRANSMITTER
FROM TRANSMIT
SYSTEM
BACKPLANE
INTERFACE
TO TRANSMIT
FRAMER
109 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.25.3 BERT Repetitive Pattern Set
These registers must be properly loaded for the BERT to generate and synchronize to a repetitive pattern, a
pseudorandom pattern, alternating word pattern, or a Daly pattern. For a repetitive pattern that is fewer than 32
bits, the pattern should be repeated so that all 32 bits are used to describe the pattern. For example, if the pattern
was the repeating 5-bit pattern …01101… (where the rightmost bit is the one sent first and received first), then
TR.BRP1 should be loaded with ADh, TR.BRP2 with B5h, TR.BRP3 with D6h, and TR.BRP4 with 5Ah. For a
pseudorandom pattern, all four registers should be loaded with all 1s (i.e., FFh). For an alternating word pattern,
one word should be placed into TR.BRP1 and TR.BRP2 and the other word should be placed into TR.BRP3 and
TR.BRP4. For example, if the DDS stress pattern “7E” is to be described, the user would place 00h in TR.BRP1,
00h in TR.BRP2, 7Eh in TR.BRP3, and 7Eh in TR.BRP4 and the alternating word counter would be set to 50
(decimal) to allow 100 bytes of 00h followed by 100 bytes of 7Eh to be sent and received.
10.25.4 BERT Bit Counter
The BERT Bit Counter is comprised of TR.BBC1, TR.BBC2, TR.BBC3, and TR.BBC4. Once BERT has achieved
synchronization, this 32-bit counter increments for each data bit (i.e., clock) received. Toggling the LC control bit in
TR.BC1 can clear this counter. This counter saturates when full and sets the BBCO status bit.
10.25.5 BERT Error Counter
The BERT Error Counter is comprised of TR.BEC1, TR.BEC2, and TR.BEC3. Once BERT has achieved
synchronization, this 24-bit counter increments for each data bit received in error. Toggling the LC control bit in
TR.BC1 can clear this counter. This counter saturates when full and sets the BECO status bit.
10.25.6 BERT Alternating Word-Count Rate
When the BERT is programmed in the alternating word mode, each word repeats for the count loaded into
TR.BAWC. One word should be placed into TR.BRP1 and TR.BRP2 and the other word should be placed into
TR.BRP3 and TR.BRP4.
110 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.26 Payload Error-Insertion Function (T1 Mode Only)
An error-insertion function is available in the transceiver and is used to create errors in the payload portion of the
T1 frame in the transmit path. This function is only available in T1 mode. Errors can be inserted over the entire
frame or the user can select which channels are to be corrupted. Errors are created by inverting the last bit in the
count sequence. For example, if the error rate 1 in 16 is selected, the 16th bit is inverted. F-bits are excluded from
the count and are never corrupted. Error rate changes occur on frame boundaries. Error-insertion options include
continuous and absolute number with both options supporting selectable insertion rates.
Table 10-14. Transmit Error-Insertion Setup Sequence
STEP
ACTION
1
Enter desired error rate in the TR.ERC register. Note: If TR.ER3 through TR.ER0 = 0,
no errors are generated even if the constant error-insertion feature is enabled.
For constant error insertion, set CE = 1 (TR.ERC.4).
2A
or
2B
For a defined number of errors:
–
–
–
Set CE = 0 (TR.ERC.4)
Load TR.NOE1 and TR.NOE2 with the number of errors to be inserted
Toggle WNOE (TR.ERC.7) from 0 to 1 to begin error insertion
10.26.1 Number-of-Errors Registers
The number-of-error registers determine how many errors are generated. Up to 1023 errors can be generated. The
host loads the number of errors to be generated into the TR.NOE1 and TR.NOE2 registers. The host can also
update the number of errors to be created by first loading the prescribed value into the TR.NOE registers and then
toggling the WNOE bit in the error-rate control registers.
Table 10-15. Error Insertion Examples
VALUE
WRITE
READ
000h
001h
002h
3FFh
Do not create any errors
Create a single error
Create two errors
No errors left to be inserted
One error left to be inserted
Two errors left to be inserted
1023 errors left to be inserted
Create 1023 errors
111 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.27 Programmable Backplane Clock Synthesizer
The transceiver contains an on-chip clock synthesizer that generates a user-selectable clock output on the BPCLK
pin, referenced to the recovered receive clock (RCLKO). The synthesizer uses a phase-locked loop to generate
low-jitter clocks. Common applications include generation of port and backplane system clocks. The TR.CCR2
register is used to enable (TR.CCR2.0) and select (TR.CCR2.1 and TR.CCR2.2) the clock frequency of the BPCLK
pin.
10.28 Fractional T1/E1 Support
The transceiver can be programmed to output gapped clocks for selected channels in the receive and transmit
paths to simplify connections into a USART or LAPD controller in fractional T1/E1 or ISDN-PRI applications. The
receive and transmit paths have independent enables. Channel formats supported include 56kbps and 64kbps.
This is accomplished by assigning an alternate function to the RCHCLK and TCHCLK pins. Setting TR.CCR3.0 = 1
causes the RCHCLK pin to output a gapped clock as defined by the receive fractional T1/E1 function of the
TR.PCPR register. Setting TR.CCR3.2 = 1 causes the TCHCLK pin to output a gapped clock as defined by the
transmit fractional T1/E1 function of the TR.PCPR register. TR.CCR3.1 and TR.CCR3.3 can be used to select
between 64kbps and 56kbps operation. See Section 10.2 for details about programming the per-channel function.
In T1 mode no clock is generated at the F-bit position.
When 56kbps mode is selected, the LSB clock in the channel is omitted. Only the seven most significant bits of the
channel have clocks.
112 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.29 T1/E1/J1 Transmit Flow Diagrams
Figure 10-17. T1/J1 Transmit Flow Diagram
TSER
TSIG
T1 TRANSMIT
FLOW
Hardware
Signaling
HSIE1-3
through
PCPR
DIAGRAM
TX
ESTORE
KEY
Estore Mux
ESCR.4 TESE
- PIN
- SELECTOR
- REGISTER
TESO
Off-Chip
Connection
RDATA
From
T1_rcv_logic
TDATA
Payload
Loopback
LBCR1.1 PLB
HDLC
Engine
#1
TLINK
THMS1 H1TC.4
H1TCS1-3
H1TTSBS
H1TC.4
THMS1
HDLC FDL #1
HDLC Mux #1
HDLC
Engine
#2
THMS2 H2TC.4
H2TCS1-3
H2TC.4
THMS2
HDLC Mux #2
HDLC FDL #2
TFDL
H2TTSBS
Idle
Code
Array
Tx FDL
Zero
Stuffer
T1TCR2.5
TZSE
TCICE1-3
Idle Code Mux
T1TCR1.2
TFDLS
TFDL
FDL Mux
Loop
Code
Gen
BOC
Engine
Loop Code
TLOOP T1CCR1.0
BOC Mux
BOCC.0 SBOC
T1CCR1.2 TFM
T1TCR2.2 TD4YM
T1TCR1.0 TYEL
D4 12th Fs
Yellow
alarm
Per-Channel
Loopback
PCLR1-3
Software
Sig
Registers
FPS or
Ft/Fs
insertion
ESF Yellow
Alarm
SSIE1-3
Software Sig
F-bit Mux
TFPT T1TCR1.5
To ESF Yellow
Mux
To FDL Mux
To FDL Mux
113 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
From ESF
Yellow Alarm
From BOC Mux
From F-bit Mux
TFPT T1TCR1.5
FDL Mux
TFM T1CCR1.2
TYEL T1TCR1.0
ESF Yellow
CRC Mux
TCPT T1TCR1.5
D4 bit 2
Yellow
Alm
TFM T1CCR1.2
TD4YM T1TCR2.2
BERT
Engine
TYEL T1TCR1.0
TFUS BIC.3
F-bit
BERT Mux
BERTEN
BIC.0
BTCS1-3
from PCPR
T1TCR2.3 FBCT1
T1TCR2.4 FBCT2
F-bit
Corruption
Payload
error
insertion
NOEL != 0
ERC.4 CE
SSIE1-3
GB7S T1TCR1.3
PEICS1-3
Bit 7
stuffing
B7SE T1TCR2.0
Pulse
Density
Enforcer
T1CCR1.1 PDE
TPDV INFO1.6
CRC
Calculation
DS0
Monitor
TCM0-4 TDS0SEL.0 - .3
TDSOM
B8ZS
Encoding
T1TCR2.7 B8ZSE
Blue
Alarm
T1TCR1.1 TBL
IOCR1.0 ODF
Bipolar/
NRZ
coding
1/2 CLK/
FULL CLK
CCR1.4 ODM
TPOS
TNEG
114 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 10-18. E1 Transmit Flow Diagram
TSER
TSIG
E1 TRANSMIT
FLOW
Hardware
HSIE1-4
DIAGRAM
Signaling
through
PCPR
TX
ESTORE
Estore Mux
TESO
ESCR.4 TESE
Off-Chip
Connection
TDATA
RDATA
From
E1_rcv_logic
Payload
Loopback Mux
LBCR1.1 PLB
HDLC
Engine
#1
THMS1 H1TC.4
HDLC DS0
Mux #1
H1TCS1-4
H1TTSBS
THMS1 H1TC.4
HDLC Sa-bit
Mux #1
T1SaBE4-
T1SaBE8
H1TTSBS.4 - H1TTSBS.0
HDLC
Engine #2
THMS2 H2TC.4
H2TCS1-4
HDLC DS0
Mux #2
H2TTSBS
KEY
- PIN
THMS2 H2TC.4
HDLC Sa-bit
Mux #2
T2SaBE4-T2SaBE8
H2TTSBS.4 - H2TTSBS.0
BERT
Engine
- SELECTOR
- REGISTER
BERTEN (BIC.0)
BERT Mux
BTCS1-4
from PCPR
Idle Code
Array
TCICE1-4
Idle Code MUX
To Per-Channel Mux
115 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
From Idle
Code Mux
RDATA
From E1_rcv_logic
E1 TRANSMIT
FLOW
Per-Channel
Loopback
PCLR1-4
TNAF
DIAGRAM
H1TC.4
H2TC.4
THMS1
THMS2
Sa-bit Mux
TAF/TNAF(non Sa)
TS0 Mux
TFPT E1TCR1.7
Si-bit Mux
E1TCR1.4 TSIS
Si = CRC4 MF Align Word
(Does not overwrite E-bits)
E1TCR1.0 TCRC4
E1TCR2.2 AEBE
Si/CRC4 Mux
TLINK
Auto E-
bit Gen
TLINK Mux
Sa4S - Sa8S
E1TCR2.5 - E1TCR2.7
TSiAF
TSiNAF
TRA
TSa5
TSa6
TSa7
TSa8
Auto
RA Gen
E1TCR2.8 ARA
TSaCR
TSa4
TSaCR Mux
TS1-16
TSA1 E1TCR1.3
SSIE1-4
Software Sig
E1TCR1.0 T16S
CRC
Calculate
E1TCR1.0 TCRC4
TDS0SEL.0 - TDS0SEL.4
TCM0-TCM4
CRC Re-
calculate
CCR1.6 CRC4R
E1TCR2.1 AAIS
DS0
Monitor
TDSOM
Auto
AIS
Gen
UA1
Gen
E1TCR1.5 TUA1
E1TCR1.2 THDB3
HDB3
Encoding
To Bipolar/NRZ
coding Mux
116 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11 DEVICE REGISTERS
Ten address lines are used to address the register space. Table 11-1 shows the register map for the DS33R11.
The addressable range for the device is 0000h to 08FFh. Each Register Section is 64 bytes deep. Global Registers
are preserved for software compatibility with multiport devices. The Serial Interface (Line) Registers are used to
configure the serial port and the associated transport protocol. The Ethernet Interface (Subscriber) registers are
used to control and observe each of the Ethernet ports. The registers associated with the MAC must be configured
through indirect register write /read access due to the architecture of the device.
When writing to a register input values for unused bits and registers (those designated with “-“) should be zero, as
these bits and registers are reserved. When a register is read from, the values of the unused bits and registers
should be ignored. A latched status bit is set when an event happens and is cleared when read. The register
details are provided in the following tables.
Table 11-1. Register Address Map
SERIAL
INTERFAC
E
MAPPER/
PORT
CHIP
GLOBAL
ETHERNET
INTERFACE TRANSCEIVER
T1/E1/J1
ARBITER
BERT
SELECT REGISTERS
Ethernet
Mapper
CS=0,
CST=1
0000h–
003Fh
0040h–
007Fh
0080h–
00BFh
00C0h–
013Fh
0140h– 17Fh
—
—
T1/E1/J1
Port 1
CS=1,
CST=0
—
—
—
—
000h–0FFh
117 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1 Register Bit Maps
Table 11-2, Table 11-3, Table 11-4, Table 11-5, Table 11-6, and Table 11-7 contain the registers of the DS33R11.
Bits that are reserved are noted with a single dash “-“. All registers not listed are reserved and should be initialized
with a value of 00h for proper operation, unless otherwise noted.
11.1.1 Global Ethernet Mapper Register Bit Map
Table 11-2. Global Ethernet Mapper Register Bit Map
ADDR Name
BIT 7
ID07
BIT 6
ID06
BIT 5
ID05
BIT 4
ID04
BIT 3
ID03
BIT 2
ID02
BIT 1
ID01
BIT 0
ID00
00h
ID15
ID14
ID13
ID12
ID11
ID10
ID09
ID08
RST
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
20h
21h
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
REF_CLKO
INTM
-
-
-
-
GL.BLC1
TLCALS1
SYSCLS
LIN1RIE
LIN1RIS
SUB1IE
SUB1IS
RQ1IE
RQ1IS
BIE
RLCALS1
-
-
-
-
-
-
REFCLKS
LIN1TIE
-
-
-
LIN1TIS
-
-
-
-
-
-
-
-
-
-
-
TQ1IE
-
-
-
TQ1IS
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
BIS
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
-
-
-
LINE0
-
-
-
-
-
-
-
-
-
-
-
-
C1MRPR
C1HWPR
C1MHPR
C1HRPR
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
BISTE
BISTPF
BISTDN
Note: 22h–3Fh are reserved.
118 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.2 Arbiter Register Bit Map
Table 11-3. Arbiter Register Bit Map
ADDR NAME
BIT 7
RQSC7
TQSC7
BIT 6
RQSC6
TQSC6
BIT 5
RQSC5
TQSC5
BIT 4
RQSC4
TQSC4
BIT 3
RQSC3
TQSC3
BIT 2
RQSC2
TQSC2
BIT 1
RQSC1
TQSC1
BIT 0
RQSC0
TQSC0
40h
41h
11.1.3 BERT Register Bit Map
Table 11-4. BERT Register Bit Map
ADDR NAME
BIT 7
BIT 6
PMU
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
BCR
-
RNPL
RPIC
MPR
APRD
TNPL
TPIC
080h
Reserved
-
-
-
-
-
-
-
-
081h
082h
083h
084h
085h
086h
087h
088h
08Ah
08Bh
08Ch
08Dh
08Eh
08Fh
90h
BPCLR
-
QRSS
PTS
PLF4
PLF3
PLF2
PLF1
PLF0
BPCHR
-
-
-
PTF4
PTF3
PTF2
PTF1
PTF0
BSPB0R
BSPB1R
BSPB2R
BSPB3R
TEICR
BSP7
BSP6
BSP5
BSP4
BSP3
BSP2
BSP1
BSP0
BSP15
BSP14
BSP13
BSP12
BSP11
BSP10
BSP9
BSP8
BSP23
BSP22
BSP21
BSP20
BSP19
BSP18
BSP17
BSP16
BSP31
BSP30
BSP29
BSP28
BSP27
BSP26
BSP25
BSP24
-
-
TIER2
TIER1
TIER0
BEI
TSEI
-
Reserved
Reserved
BSR
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
PMS
-
BEC
OOS
Reserved
BSRL
-
-
-
-
-
-
-
-
-
-
-
-
PMSL
BEL
BECL
OOSL
Reserved
BSRIE
-
-
-
-
-
-
-
-
-
-
-
-
PMSIE
BEIE
BECIE
OOSIE
Reserved
Reserved
Reserved
RBECB0R
RBECB1R
RBECB2R
Reserved
RBCB0
-
-
-
-
-
-
-
-
91h
92h
93h
94h
95h
96h
97h
98h
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
BEC7
BEC6
BEC5
BEC4
BEC3
BEC2
BEC1
BEC0
BEC15
BEC14
BEC13
BEC12
BEC11
BEC10
BEC9
BEC8
BEC23
BEC22
BEC21
BEC20
BEC19
BEC18
BEC17
BEC16
-
-
-
-
-
-
-
-
BC7
BC6
BC5
BC4
BC3
BC2
BC1
BC0
RBCB1
BC15
BC14
BC13
BC12
BC11
BC10
BC9
BC8
99h
RBCB2
BC23
BC22
BC21
BC20
BC19
BC18
BC17
BC16
9Ah
RBCB3
BC31
BC30
BC29
BC28
BC27
BC26
BC25
BC24
9Bh
Reserved
Reserved
Reserved
Reserved
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9Ch
9Dh
9Eh
9Fh
119 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.4 Serial Interface Register Bit Map
Table 11-5. Serial Interface Register Bit Map
ADDR NAME
LI.TSLCR
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TDENPLT
-
-
-
-
-
-
-
-
0C0h
0C1h
0C2h
0C3h
0C4h
0C5h
0C6h
0C7h
0C8h
0C9h
0CAh
0CBh
0CCh
0CDh
0CEh
0CFh
0D0h
0D1h
0D2h
0D3h
0D4h
0D5h
0D6h
LI.RSTPD
LI.LPBK
-
-
-
-
-
-
RESET
-
-
-
-
-
-
-
QLP
Reserved
LI.TPPCL
LI.TIFGC
LI.TEPLC
LI.TEPHC
LI.TPPSR
LI.TPPSRL
LI.TPPSRIE
Reserved
LI.TPCR0
LI.TPCR1
LI.TPCR2
Reserved
LI.TBCR0
-
-
-
-
-
-
-
-
-
-
TFAD
TF16
TIFV
TSD
TBRE
-
TIFG7
TIFG6
TIFG5
TIFG4
TIFG3
TIFG2
TIFG1
TIFG0
TPEN0
TPER0
TEPF
TEPFL
TEPFIE
-
TPEN7
TPEN6
TPEN5
TPEN4
TPEN3
TPEN2
TPEN1
MEIMS
TPER6
TPER5
TPER4
TPER3
TPER2
TPER1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
TPC7
TPC15
TPC23
-
TPC6
TPC14
TPC22
-
TPC5
TPC13
TPC21
-
TPC4
TPC12
TPC20
-
TPC3
TPC11
TPC19
-
TPC2
TPC10
TPC18
-
TPC1
TPC9
TPC17
-
TPC0
TPC8
TPC16
-
TBC7
TBC15
TBC23
TBC31
-
TBC6
TBC14
TBC22
TBC30
-
TBC5
TBC13
TBC21
TBC29
-
TBC4
TBC12
TBC20
TBC28
-
TBC3
TBC11
TBC19
TBC27
-
TBC2
TBC10
TBC18
TBC26
-
TBC1
TBC9
TBC17
TBC25
-
TBC0
TBC8
TBC16
TBC24
TMEI
-
Reserved
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
TPMUU
TPMUS
X86ED
0D7h
0D8h
X86TRA7
X86TRC7
X86TRA6
X86TRC6
X86TRA5
X86TRC5
X86TRA4
X86TRC4
X86TRA3
X86TRC3
X86TRA2
X86TRC2
X86TRA1
X86TRC1
X86TRA0
X86TRC0
0D9h
0DAh
0DBh
0DCh
0DDh
100h
101h
102h
103h
104h
105h
106h
107h
108h
109h
10Ah
LI.TRX86SAPIH TRSAPIH7 TRSAPIH6 TRSAPIH5 TRSAPIH4 TRSAPIH3 TRSAPIH2 TRSAPIH1 TRSAPIH0
LI.TRX86SAPIL TRSAPIL7
TRSAPIL6
TRSAPIL5
CIR5
TRSAPIL4
CIR4
TRSAPIL3
CIR3
TRSAPIL2
CIR2
TRSAPIL1
CIR1
TRSAPIL0
CIR0
CIRE
-
CIR6
-
Reserved
-
-
-
-
-
RDENPLT
RCCE
-
-
RFPD
RMX5
RMX13
-
RF16
RMX4
RMX12
-
RFED
RMX3
RMX11
-
RDD
RBRE
RMX1
RMX9
RAPC
RAPCL
RAPCIE
RMX7
RMX15
-
RMX6
RMX14
-
RMX2
RMX10
REPC
REPCL
REPCIE
RMX0
RMX8
RSPC
REPL
REPIE
RAPL
RAPIE
RIPDL
RIPDIE
RSPDL
RSPDIE
RLPDL
RLPDIE
RSPCL
RSPCIE
RPC7
RPC15
RPC23
RFPC7
RFPC15
RFPC23
RPC6
RPC14
RPC22
RFPC6
RFPC14
RFPC22
RPC5
RPC13
RPC21
RFPC5
RFPC13
RFPC21
RPC4
RPC12
RPC20
RFPC4
RFPC12
RFPC20
RPC3
RPC11
RPC19
RFPC3
RFPC11
RFPC19
RPC2
RPC10
RPC18
RFPC2
RFPC10
RFPC18
RPC1
RPC09
RPC17
RFPC1
RFPC9
RFPC17
RPC0
RPC08
RPC16
RFPC0
RFPC8
RFPC16
10Ch LI.RFPCB0
10Dh
10Eh
Reserved
10Fh
RAPC7
RAPC15
RAPC23
-
RAPC6
RAPC14
RAPC22
-
RAPC5
RAPC13
RAPC21
-
RAPC4
RAPC12
RAPC20
-
RAPC3
RAPC11
RAPC19
-
RAPC2
RAPC10
RAPC18
-
RAPC1
RAPC9
RAPC17
-
RAPC0
RAPC8
RAPC16
-
110h
111h
112h
113h
Reserved
120 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR NAME
BIT 7
RSPC7
BIT 6
RSPC6
BIT 5
RSPC5
BIT 4
RSPC4
BIT 3
RSPC3
BIT 2
RSPC2
BIT 1
RSPC1
BIT 0
RSPC0
114h
115h
116h
118h
119h
11Ah
11Bh
11Ch
11Dh
11Eh
11Fh
120h
RSPC15
RSPC23
RBC7
RSPC14
RSPC22
RBC6
RSPC13
RSPC21
RBC5
RSPC12
RSPC20
RBC4
RSPC11
RSPC19
RBC3
RSPC10
RSPC18
RBC2
RSPC9
RSPC17
RBC1
RSPC8
RSPC16
RBC0
RBC15
RBC23
RBC31
REBC7
REBC15
REBC23
REBC31
RBC14
RBC22
RBC30
REBC6
REBC14
REBC22
REBC30
RBC13
RBC21
RBC29
REBC5
REBC13
REBC21
REBC29
RBC12
RBC20
RBC28
REBC4
REBC12
REBC20
REBC28
RBC11
RBC19
RBC27
REBC3
REBC11
REBC19
REBC27
RBC10
RBC18
RBC26
REBC2
REBC10
REBC18
REBC26
RBC9
RBC8
RBC17
RBC25
REBC1
REBC9
REBC17
REBC25
RBC16
RBC24
REBC0
REBC8
REBC16
REBC24
-
-
-
-
-
-
-
-
-
-
-
-
RPMUU
121h
-
-
RPMUUS
-
-
-
-
SAPIHNE
SAPILNE
CNE
ANE
122h
123h
124h
125h
126h
127h
SAPINE01IM SAPINEFEIM
-
-
-
-
CNE3LIM
TQLT1
ANE4IM
TQLT0
TQHT0
TQLTIE
TQLTLS
TQLT7
TQLT6
TQLT5
TQLT4
TQLT3
TQHT3
TQLT2
TQHT2
TQHT7
TQHT6
TQHT5
TQHT4
TQHT1
TQHTIE
TQHTLS
-
-
-
-
-
-
-
-
TFOVFIE
TFOVFLS
TQOVFIE
TQOVFLS
Note: 0DEh–0FFh, 128h–13Fh are reserved.
121 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.5 Ethernet Interface Register Bit Map
Table 11-6. Ethernet Interface Register Bit Map
ADDR NAME
BIT 7
MACRA7
BIT 6
MACRA6
BIT 5
MACRA5
BIT 4
MACRA4
BIT 3
MACRA3
BIT 2
MACRA2
BIT 1
MACRA1
BIT 0
MACRA0
140h
141h
142h
143h
144h
145h
146h
147h
148h
149h
14Ah
14Bh
14Ch
14Eh
14Fh
150h
151h
152h
153h
154h
155h
156h
157h
158h
159h
15Ah
15Bh
15Ch
15Dh
15Eh
RESERVED
MACRA15
MACRD7
MACRA14
MACRD6
MACRA13
MACRD5
MACRA12
MACRD4
MACRA11
MACRD3
MACRA10
MACRD2
MACRA09
MACRD1
MACRD9
MACRA08
MACRD0
MACRD8
MACRD15 MACRD14 MACRD13 MACRD12 MACRD11 MACRD10
MACRD23 MACRD22 MACRD21 MACRD20 MACRD19 MACRD18 MACRD17 MACRD16
MACRD31 MACRD30 MACRD29 MACRD28 MACRD27 MACRD26 MACRD25 MACRD24
MACWD7
MACWD6
MACWD5
MACWD4
MACWD3
MACWD2
MACWD1
MACWD0
MACWD15 MACWD14 MACWD13 MACWD12 MACWD11 MACWD10 MACWD09 MACWD08
MACWD23 MACWD22 MACWD21 MACWD20 MACWD19 MACWD18 MACWD17 MACWD16
MACD31
MACD30
MACD29
MACD28
MACAW4
MACD27
MACAW3
MACD26
MACAW2
MACD25
MACAW1
MACAW9
MCRW
-
MACD24
MACAW0
MACAW8
MCS
MACAW 7
MACAW 6
MACAW 5
MACAW 15 MACAW 14 MACAW 13 MACAW12 MACAW11 MACAW10
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
QLP
-
-
-
-
CRCS
NCFQ
LOC
H10S
TPDFCB
NOC
ATFLOW
TPRHBC
-
JAME
TPRCB
FABORT
DEF
-
-
EC
-
UR
LC
ED
PR
HBF
FL6
CC3
FL5
CC2
FL4
FL12
DB
CC1
CC0
LCO
FL7
FL3
FL2
FL1
Fl0
RF
WT
FL13
CRCE
-
FL11
FL10
FL9
Fl8
-
-
MIIE
FT
CS
FTL
MF
-
BF
MCF
UF
CF
LE
RMPS7
RMPS6
RMPS14
RQLT6
RQHT6
-
RMPS5
RMPS13
RQLT5
RQHT5
-
RMPS4
RMPS12
RQLT4
RQHT4
-
RMPS3
RMPS11
RQLT3
RQHT3
RFOVFIE
RFOVFLS
CRCERR
RMPS2
RMPS10
RQLT2
RQHT2
RQVFIE
RQOVFLS
DBR
RMPS1
RMPS09
RQLT1
RQHT1
RQLTIE
RQHTLS
MIIER
RMPS0
RMPS08
RQLT0
RQHT0
RQHTIE
RQLTLS
BFR
RMPS15
RQLT7
RQHT7
-
-
-
-
-
-
UCFR
CFRR
LERR
Note: 15Fh–17Fh are reserved.
122 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.1.6 MAC Register Bit Map
Table 11-7. MAC Indirect Register Bit Map
ADDR
NAME
31:24
BIT 7
Reserved
BIT 6
Reserved
BIT 5
Reserved
BIT 4
HDB
BIT 3
PS
BIT 2
Reserved
BIT 1
Reserved
BIT 0
Reserved
0000h
23:16
DRO
OML1
OML0
F
PM
PAM
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
ASTP
0001h
0002h
0003h
0004h
0005h
0006h
0007h
0008h
0009h
000Ah
000Bh
000Ch
000Dh
000Eh
000Fh
0010h
0011h
0012h
0013h
15:8
Reserved
BOLMT1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
BOLMT0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
DC
LCC
Reserved
TE
DRTY
7:0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RE
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
31:24
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0014h
23:16
Reserved
PHYA4
MIIA1
Reserved
PHYA3
MIIA0
Reserved
PHYA2
Reserved
PHYA1
Reserved
PHYA0
Reserved
MIIA4
Reserved
MIIA3
Reserved
MIIA2
0015h
0016h
0017h
15:8
7:0
Reserved
Reserved
Reserved
Reserved
MIIW
MIIB
31:24
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0018h
23:16
Reserved
MIID15
Reserved
MIID14
Reserved
MIID13
Reserved
MIID12
Reserved
MIID11
Reserved
MIID10
Reserved
MIID09
Reserved
MIID08
0019h
001Ah
001Bh
15:8
7:0
MIID07
MIID06
MIID05
MIID04
MIID03
MIID02
MIID01
MIID00
31:24
PT15
PT14
PT13
PT12
PT11
PT10
PT09
PT08
001Ch
23:16
PT07
PT06
PT05
PT04
PT03
PT02
Reserved
PCF
PT01
Reserved
FCE
PT00
Reserved
FCB
001Dh
001Eh
001Fh
100h
15:8
7:0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
SU.MMCCTRL
31:24
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
23:16
Reserved
Reserved
MXFRM4
Reserved
Reserved
MXFRM3
Reserved
MXFRM10
MXFRM2
Reserved
MXFRM9
MXFRM1
Reserved
MXFRM8
MXFRM0
Reserved
MXFRM7
Reserved
Reserved
MXFRM6
Reserved
Reserved
MXFRM5
Reserved
101h
102h
103h
10Ch
15:8
7:0
RESERVED –
initialize to FF
RESERVED –
initialize to FF
RESERVED –
initialize to FF
RESERVED –
initialize to FF
RESERVED –
initialize to FF
RESERVED –
initialize to FF
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
10Dh
10Eh
10Fh
110h
111h
123 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADDR
112h
NAME
RESERVED –
initialize to FF
RESERVED –
initialize to FF
SU.RxFrmCtr
31:24
BIT 7
Reserved
BIT 6
Reserved
BIT 5
Reserved
BIT 4
Reserved
BIT 3
Reserved
BIT 2
Reserved
BIT 1
Reserved
BIT 0
Reserved
113h
200h
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
RXFRMC31 RXFRMC30 RXFRMC29 RXFRMC28 RXFRMC27 RXFRMC26 RXFRMC25 RXFRMC24
23:16
RXFRMC23 RXFRMC22 RXFRMC21 RXFRMC20 RXFRMC19 RXFRMC18 RXFRMC17 RXFRMC16
RXFRMC15 RXFRMC14 RXFRMC13 RXFRMC12 RXFRMC11 RXFRMC10 RXFRMC9 RXFRMC8
RXFRMC7 RXFRMC6 RXFRMC5 RXFRMC4 RXFRMC3 RXFRMC2 RXFRMC1 RXFRMC0
201h
202h
203h
204h
15:8
7:0
SU.RxFrmOKCtr
31:24
RXFRMOK31 RXFRMOK30 RXFRMOK29 RXFRMOK28 RXFRMOK27 RXFRMOK26 RXFRMOK25 RXFRMOK24
RXFRMOK23 RXFRMOK22 RXFRMOK21 RXFRMOK20 RXFRMOK19 RXFRMOK18 RXFRMOK17 RXFRMOK16
23:16
205h
206h
207h
300h
301h
302h
303h
308h
309h
30Ah
30Bh
30Ch
30Dh
30Eh
30Fh
334h
335h
336h
337h
338h
339h
33Ah
33Bh
15:8
7:0
RXFRMOK15 RXFRMOK14 RXFRMOK13 RXFRMOK12 RXFRMOK11 RXFRMOK10 RXFRMOK9
RXFRMOK8
RXFRMOK0
TXFRMC24
TXFRMC16
TXFRMC8
TXFRMC0
RXFRMOK7
TXFRMC31
TXFRMC23
TXFRMC15
TXFRMC7
RXFRMOK6
TXFRMC30
TXFRMC22
TXFRMC14
TXFRMC6
RXFRMOK5
TXFRMC29
TXFRMC21
TXFRMC13
TXFRMC5
RXFRMOK4
TXFRMC28
TXFRMC20
TXFRMC12
TXFRMC4
RXFRMOK3
TXFRMC27
TXFRMC19
TXFRMC11
TXFRMC3
RXFRMOK2
TXFRMC26
TXFRMC18
TXFRMC10
TXFRMC2
RXFRMOK1
TXFRMC25
TXFRMC17
TXFRMC9
TXFRMC1
SU.TxFrmCtr
23:16
15:8
7:0
SU.TxBytesCtr
23:16
TXBYTEC31 TXBYTEC30 TXBYTEC29 TXBYTEC28 TXBYTEC27 TXBYTEC26 TXBYTEC25 TXBYTEC24
TXBYTEC23 TXBYTEC22 TXBYTEC21 TXBYTEC20 TXBYTEC19 TXBYTEC18 TXBYTEC17 TXBYTEC16
15:8
TXBYTEC15 TXBYTEC14 TXBYTEC13 TXBYTEC12 TXBYTEC11 TXBYTEC10
TXBYTEC7 TXBYTEC6 TXBYTEC5 TXBYTEC4 TXBYTEC3 TXBYTEC2
TXBYTEC9
TXBYTEC1
TXBYTEC8
TXBYTEC0
7:0
SU.TxBytesOkCtr
TXBYTEOK31 TXBYTEOK30 TXBYTEOK29 TXBYTEOK28 TXBYTEOK27 TXBYTEOK26 TXBYTEOK25 TXBYTEOK24
TXBYTEOK23 TXBYTEOK22 TXBYTEOK21 TXBYTEOK20 TXBYTEOK19 TXBYTEOK18 TXBYTEOK17 TXBYTEOK16
TXBYTEOK15 TXBYTEOK14 TXBYTEOK13 TXBYTEOK12 TXBYTEOK11 TXBYTEOK10 TXBYTEOK9 TXBYTEOK8
TXBYTEOK7 TXBYTEOK6 TXBYTEOK5 TXBYTEOK4 TXBYTEOK3 TXBYTEOK2 TXBYTEOK1 TXBYTEOK0
23:16
15:8
7:0
SU.TxFrmUndr
23:16
TXFRMU31
TXFRMU23
TXFRMU15
TXFRMU7
TXFRMU30
TXFRMU22
TXFRMU14
TXFRMU6
TXFRMU29
TXFRMU21
TXFRMU13
TXFRMU5
TXFRMU28
TXFRMU20
TXFRMU12
TXFRMU4
TXFRMU27
TXFRMU19
TXFRMU11
TXFRMU3
TXFRMU26
TXFRMU18
TXFRMU10
TXFRMU2
TXFRMU25
TXFRMU17
TXFRMU9
TXFRMU1
TXFRMU24
TXFRMU16
TXFRMU8
TXFRMU0
15:8
7:0
SU.TxBdFrmCtr
TXFRMBD31 TXFRMBD30 TXFRMBD29 TXFRMBD28 TXFRMBD27 TXFRMBD26 TXFRMBD25 TXFRMBD24
TXFRMBD23 TXFRMBD22 TXFRMBD21 TXFRMBD20 TXFRMBD19 TXFRMBD18 TXFRMBD17 TXFRMBD16
23:16
15:8
7:0
TXFRMBD15 TXFRMBD14 TXFRMBD13 TXFRMBD12 TXFRMBD11 TXFRMBD10 TXFRMBD9
TXFRMBD7 TXFRMBD6 TXFRMBD5 TXFRMBD4 TXFRMBD3 TXFRMBD2 TXFRMBD1
TXFRMBD8
TXFRMBD0
Note that the addresses in the table above are the indirect addresses that must be provided to the SU.MACAWH and SU.MACAWL. All
unused and reserved locations must be initialized to zero for proper operation.
124 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 11-8. T1/E1/J1 Transceiver Register Bit Map (Active when CST = 0)
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
000
h
001
h
002
h
003
h
004
h
005
h
006
h
007
h
—
—
—
—
TEST1
TSDW
RSYNCINV TSYNCINV TSSYNCINV
TEST0
T1/E1
SFTRST
ODF
TR.MSTRREG
TR.IOCR1
RSMS
RSMS2
RSMS1
RSIO
TSM
H100EN
SYNCT
—
TSIO
TSCLKM
SYNCE
RJC
RDCLKIN
V
TDCLKIN
V
RSCLKM
RESYNC
RD4YM
TYEL
TR.IOCR2
—
—
ARC
RFM
OOF1
RB8ZS
TCPT
TZSE
—
OOF2
RSLC96
TSSE
SYNCC
RZSE
TR.T1RCR1
TR.T1RCR2
TR.T1TCR1
TR.T1TCR2
TR.T1CCR1
TJC
TB8ZS
—
TFPT
TSLC96
—
GB7S
TFDLS
TD4YM
TFM
TBL
FBCT2
TRAI-CI
FBCT1
TAIS-CI
Reserved
PDE
TB7ZS
TLOOP
008
h
CH8
CH7
CH7
CH6
CH6
CH5
CH5
CH4
CH4
CH3
CH3
CH2
CH2
CH1
CH1
UCAW
TR.SSIE1-T1
TR.SSIE1-E1
009
h
CH16
CH15
CH15
CH14
CH14
CH13
CH13
CH12
CH12
CH11
CH11
CH10
CH10
CH9
CH9
CH8
TR.SSIE2-T1
TR.SSIE2-E1
00A
h
CH24
CH22
CH23
CH21
CH22
CH20
CH21
CH19
CH20
CH18
CH19
CH17
CH18
CH16
CH17
LCAW
TR.SSIE3-T1
TR.SSIE3-E1
00B
h
00C
h
00D
h
00E
h
CH30
CH8
CH16
CH24
ID7
CH29
CH7
CH15
CH23
ID6
CH28
CH6
CH27
CH5
CH13
CH21
ID4
CH26
CH4
CH12
CH20
ID3
CH25
CH3
CH24
CH2
CH23
CH1
TR.SSIE4
TR.T1RDMR1
TR.T1RDMR2
TR.T1RDMR3
TR.IDR
CH14
CH22
ID5
CH11
CH19
ID2
CH10
CH18
ID1
CH9
CH17
ID0
00F
h
010
h
011
h
012
h
013
h
014
h
015
h
RPDV
BSYNC
—
TPDV
BD
COFA
TCLE
—
8ZD
TOCD
—
16ZD
RL3
—
SEFE
RL2
B8ZS
RL1
FBE
TR.INFO1
TR.INFO2
TR.INFO3
Reserved
TR.IIR1
RL0
—
CRCRC
—
FASRC
—
CASRC
—
—
—
—
—
—
SR8
—
SR7
—
SR6
SR5
—
SR4
—
SR3
SR2
SR1
—
—
—
SR9
TR.IIR2
016
h
017
h
ILUT
ILUT
TIMER
TIMER
RSCOS
RSCOS
JALT
JALT
LRCL
LRCL
TCLE
TCLE
TOCD
TOCD
LOLITC
LOLITC
TR.SR1
TR.IMR1
018
h
019
RYELC
RYELC
RUA1C
RUA1C
FRCLC
FRCLC
RLOSC
RLOSC
RYEL
RYEL
RUA1
RUA1
FRCL
FRCL
RLOS
RLOS
TR.SR2
TR.IMR2
125 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
h
01A
h
01B
h
01C
h
01D
h
01E
h
01F
h
020
h
021
h
022
h
023
h
024
h
025
h
026
h
027
h
028
h
029
h
02A
h
02B
h
02C
h
02D
h
02E
h
02F
h
030
h
031
h
LSPARE
LSPARE
RAIS-CI
RAIS-CI
—
LDN
LDN
LUP
LOTC
LORC
V52LNK
V52LNK
RMF
RDMA
RRA
TR.SR3
LUP
RSA0
RSA0
TESF
TESF
RPE
LOTC
TMF
LORC
TAF
RDMA
RCMF
RCMF
RESEM
RESEM
TLWM
TLWM
TLWM
TLWM
RMTCH
RMTCH
BRLOS
BRLOS
TFCS
CH2
RRA
RAF
TR.IMR3
TR.SR4
RSA1
RSA1
—
TMF
TAF
RMF
RAF
TR.IMR4
TR.SR5
TESEM
TESEM
RPS
TSLIP
TSLIP
RHWM
RHWM
RHWM
RHWM
RFDLF
RFDLF
BRA1
RESF
RESF
RNE
RSLIP
RSLIP
TNF
—
—
TR.IMR5
TR.SR6
—
TMEND
TMEND
TMEND
TMEND
—
—
RPE
RPS
RNE
TNF
TR.IMR6
TR.SR7
—
RPE
RPS
RNE
TNF
—
RPE
RPS
RNE
TNF
TR.IMR7
TR.SR8
—
BOCC
BOCC
BBCO
BBCO
RFCS
CH6
RFDLAD
RFDLAD
BEC0
BEC0
BRCS
CH5
TFDLE
TFDLE
BRA0
BRA0
PEICS
CH3
RBOC
RBOC
BSYNC
BSYNC
BTCS
CH1
—
—
TR.IMR8
TR.SR9
—
BBED
BBED
RSRCS
CH7
—
BRA1
TR.IMR9
TR.PCPR
TR.PCDR1
TR.PCDR2
TR.PCDR3
TR.PCDR4
TR.INFO4
TR.INFO5
TR.INFO6
TR.INFO7
TR.H1RC
TR.H2RC
RSAOICS
CH8
CH16
CH24
CH32
—
THSCS
CH4
CH15
CH23
CH31
—
CH14
CH22
CH30
—
CH13
CH21
CH29
—
CH12
CH11
CH19
CH27
H2OBT
PS2
CH10
CH18
CH26
H1UDR
PS1
CH9
CH20
CH17
CH25
H1OBT
PS0
CH28
H2UDR
REMPTY
REMPTY
CSC0
—
—
TEMPTY
TEMPTY
CSC3
—
TFULL
TFULL
CSC2
—
—
—
PS2
PS1
PS0
CSC5
RHR
RHR
CSC4
RHMS
RHMS
FASSA
—
CASSA
—
CRC4SA
RSFD
RSFD
HDLCD
HDLCD
032
h
—
—
—
—
033
h
034
RSERC
—
RSIGM
—
RHDB3
—
RG802
—
RCRC4
—
FRC
—
SYNCE
—
RESYNC
RCLA
TR.E1RCR1
TR.E1RCR2
126 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
h
035
h
036
h
037
h
038
h
039
h
03A
h
03B
h
03C
h
03D
h
03E
h
03F
h
040
h
041
h
042
h
043
h
044
h
TFPT
T16S
TUA1
TSiS
TSA1
THDB3
TG802
TCRC4
TR.E1TCR1
TR.E1TCR2
TR.BOCC
Reserved
—
Reserved
—
Reserved
—
Reserved
RBOCE
CH5
Reserved
RBR
AEBE
RBF1
CH3
AAIS
RBF0
CH2
ARA
SBOC
CH1
CH8
CH7
CH6
CH4
TR.RSINFO1
TR.RSINFO2
TR.RSINFO3
TR.RSINFO4
TR.RSCSE1
TR.RSCSE2
TR.RSCSE3
TR.RSCSE4
TR.SIGCR
CH16
CH24
—
CH15
CH23
—
CH14
CH22
CH30
CH6
CH13
CH21
CH29
CH5
CH12
CH20
CH28
CH4
CH11
CH19
CH27
CH3
CH10
CH18
CH26
CH2
CH9
CH17
CH25
CH1
CH8
CH7
CH16
CH24
—
CH15
CH23
—
CH14
CH22
CH30
—
CH13
CH21
CH29
RFE
CH12
CH20
CH28
RFF
CH11
CH19
CH27
RCCS
FSBE
LCVC10
LCVC2
PCVC10
PCVC2
FOS10
FOS2
EB10
EB2
CH10
CH18
CH26
TCCS
MOSCRF
LCVC9
LCVC1
PCVC9
PCVC1
FOS9
FOS1
EB9
CH9
CH17
CH25
FRSAO
LCVCRF
LCCV8
LCVC0
PCVC8
PCVC0
FOS8
FOS0
EB8
GRSRE
—
—
MECU
LCVC14
LCVC6
PCVC14
PCVC6
FOS14
FOS6
EB14
EB6
ECUS
LCVC13
LCVC5
PCVC13
PCVC5
FOS13
FOS5
EB13
EB5
EAMS
LCVC12
LCVC4
PCVC12
PCVC4
FOS12
FOS4
EB12
VCRFS
LCVC11
LCVC3
PCVC11
PCVC3
FOS11
FOS3
EB11
EB3
TR.ERCNT
TR.LCVCR1
TR.LCVCR2
TR.PCVCR1
TR.PCVCR2
TR.FOSCR1
TR.FOSCR2
TR.EBCR1
TR.EBCR2
TR.LBCR
LCVC15
LCVC7
PCVC15
PCVC7
FOS15
FOS7
EB15
EB7
045
h
046
h
047
h
048
h
049
h
04A
h
EB4
EB1
EB0
LTS
—
—
LIUC
LLB
RLB
PLB
FLB
04B
h
CH8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
TR.PCLR1
04C
h
04D
h
CH16
CH24
CH15
CH23
CH14
CH22
CH13
CH21
CH12
CH20
CH11
CH19
CH10
CH18
CH9
TR.PCLR2
CH17
TR.PCLR3
04E
h
04F
CH32
CH31
TESR
CH30
CH29
TESE
CH28
CH27
RESR
CH26
CH25
RESE
TR.PCLR4
TR.ESCR
TESALGN
TESMDM
RESALGN
RESMDM
127 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
h
050
h
051
h
052
h
053
h
054
h
055
h
056
h
057
h
058
h
059
h
05A
h
05B
h
05C
h
05D
h
05E
h
05F
h
060
h
061
h
062
h
063
h
064
h
065
h
066
h
067
h
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Transmit Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
TR.TS1
TR.TS2
TR.TS3
TR.TS4
TR.TS5
TR.TS6
TR.TS7
TR.TS8
TR.TS9
TR.TS10
TR.TS11
TR.TS12
TR.TS13
TR.TS14
TR.TS15
TR.TS16
TR.RS1
TR.RS2
TR.RS3
TR.RS4
TR.RS5
TR.RS6
TR.RS7
TR.RS8
TR.RS9
TR.RS10
068
h
069
h
128 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
06A
h
06B
h
06C
h
06D
h
06E
h
06F
h
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
Receive Signaling Bit Format Changes With Operating Mode. See Register Definition.
TR.RS11
TR.RS12
TR.RS13
TR.RS14
TR.RS15
TR.RS16
070
h
071
h
072
h
073
h
074
h
075
h
076
h
077
h
078
h
079
h
07A
h
07B
h
07C
h
07D
h
07E
h
07F
h
—
—
—
CRC4R
—
SIE
—
ODM
—
—
—
TCSS1
BPCS1
TCSS0
BPCS0
RLOSF
BPEN
TR.CCR1
TR.CCR2
TR.CCR3
TR.CCR4
TR.TDS0SEL
TR.TDS0M
TR.RDS0SEL
TR.RDS0M
TR.LIC1
—
—
—
TDATFMT
UOP3
TCM3
B5
TGPCKEN RDATFMT RGPCKEN
RLT3
RLT2
—
RLT1
—
RLT0
TCM4
B4
UOP2
TCM2
B6
UOP1
TCM1
B7
UOP0
TCM0
B8
—
B1
B2
B3
—
—
—
RCM4
B4
RCM3
B5
RCM2
B6
RCM1
B7
RCM0
B8
B1
B2
B3
L2
L1
L0
EGL
TUA1
MM1
MPS0
—
JAS
JABDS
—
DJA
TPD
CLDS
TAOZ
RT0
ETS
—
LIRST
TCES
CMII
—
IBPV
RCES
MPS1
—
JAMUX
MM0
TT1
SCLD
TSCLKE
RT1
TR.LIC2
RSCLKE
TT0
TR.LIC3
CMIE
—
TR.LIC4
—
—
—
—
Reserved
TR.TLBC
TR.IAAR
—
AGCD
GTIC
C6
GC5
IAA5
C5
GC4
IAA4
C4
GC3
IAA3
C3
GC2
IAA2
C2
GC1
IAA1
C1
GC0
IAA0
C0
GRIC
C7
TR.PCICR
TR.TCICE1
TR.TCICE2
TR.TCICE3
TR.TCICE4
TR.RCICE1
080
h
081
h
082
h
083
h
CH8
CH16
CH24
CH32
CH8
CH7
CH15
CH23
CH31
CH7
CH6
CH14
CH22
CH30
CH6
CH5
CH13
CH21
CH29
CH5
CH4
CH3
CH11
CH19
CH27
CH3
CH2
CH1
CH9
CH17
CH25
CH1
CH12
CH20
CH28
CH4
CH10
CH18
CH26
CH2
084
h
129 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
085
h
086
h
087
h
088
h
089
h
08A
h
08B
h
08C
h
08D
h
08E
h
08F
h
090
h
091
h
092
h
093
h
094
h
095
h
096
h
097
h
098
h
099
h
09A
h
09B
h
09C
h
CH16
CH15
CH14
CH13
CH12
CH11
CH10
CH9
TR.RCICE2
TR.RCICE3
TR.RCICE4
TR.RCBR1
TR.RCBR2
TR.RCBR3
TR.RCBR4
TR.TCBR1
TR.TCBR2
TR.TCBR3
TR.TCBR4
TR.H1TC
CH24
CH32
CH23
CH31
CH22
CH30
CH21
CH29
CH20
CH28
CH19
CH27
CH18
CH26
CH17
CH25
CH8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
CH16
CH15
CH14
CH13
CH12
CH11
CH10
CH9
CH24
CH23
CH22
CH21
CH20
CH19
CH18
CH17
CH32
CH31
CH30
CH29
CH28
CH27
CH26
CH25
CH8
CH7
CH6
CH5
CH4
CH3
CH2
CH1
CH16
CH15
CH14
CH13
CH12
CH11
CH10
CH9
CH24
CH23
CH22
CH21
CH20
CH19
CH18
CH17
CH32
CH31
CH30
CH29
CH28
CH27
CH26
CH25
NOFS
—
TEOML
—
THR
THMS
TFS
TEOM
RFHWM2
RHCS3
RHCS11
RHCS19
RHCS27
RCB3SE
THCS3
THCS11
THCS19
THCS27
TCB3SE
RPBA2
THD2
TZSD
TCRCD
RFHWM0
RHCS1
RHCS9
RHCS17
RHCS25
RCB1SE
THCS1
THCS9
THCS17
THCS25
TCB1SE
RPBA0
THD0
TFLWM2
RHCS6
RHCS14
RHCS22
RHCS30
RCB6SE
THCS6
THCS14
THCS22
THCS30
TCB6SE
RPBA5
THD5
TFLWM1
RHCS5
RHCS13
RHCS21
RHCS29
RCB5SE
THCS5
THCS13
THCS21
THCS29
TCB5SE
RPBA4
THD4
TFLWM0
RHCS4
RHCS12
RHCS20
RHCS28
RCB4SE
THCS4
THCS12
THCS20
THCS28
TCB4SE
RPBA3
THD3
RFHWM1
RHCS2
RHCS10
RHCS18
RHCS26
RCB2SE
THCS2
THCS10
THCS18
THCS26
TCB2SE
RPBA1
THD1
TR.H1FC
RHCS8
RHCS16
RHCS24
RHCS32
RCB8SE
THCS8
THCS16
THCS24
THCS32
TCB8SE
MS
RHCS7
RHCS15
RHCS23
RHCS31
RCB7SE
THCS7
THCS15
THCS23
THCS31
TCB7SE
RPBA6
THD6
TR.H1RCS1
TR.H1RCS2
TR.H1RCS3
TR.H1RCS4
TR.H1RTSBS
TR.H1TCS1
TR.H1TCS2
TR.H1TCS3
TR.H1TCS4
TR.H1TTSBS
TR.H1RPBA
TR.H1TF
09D
h
THD7
09E
h
09F
h
RHD7
TFBA7
RHD6
RHD5
RHD4
RHD3
RHD2
RHD1
RHD0
TR.H1RF
TFBA6
TFBA5
TFBA4
TFBA3
TFBA2
TFBA1
TFBA0
TR.H1TFBA
130 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0A0
h
0A1
h
0A2
h
0A3
h
0A4
h
0A5
h
0A6
h
0A7
h
0A8
h
0A9
h
0AA
h
0AB
h
0AC
h
0AD
h
0AE
h
0AF
h
NOFS
TEOML
—
THR
THMS
TFS
TEOM
TZSD
TCRCD
TR.H2TC
—
RHCS8
RHCS16
RHCS24
RHCS32
RCB8SE
THCS8
THCS16
THCS24
THCS32
TCB8SE
MS
TFLWM2
RHCS6
RHCS14
RHCS22
RHCS30
RCB6SE
THCS6
THCS14
THCS22
THCS30
TCB6SE
RPBA5
THD5
RHD5
TFBA5
RUP2
C5
TFLWM1
RHCS5
RHCS13
RHCS21
RHCS29
RCB5SE
THCS5
THCS13
THCS21
THCS29
TCB5SE
RPBA4
THD4
RHD4
TFBA4
RUP1
C4
TFLWM0
RHCS4
RHCS12
RHCS20
RHCS28
RCB4SE
THCS4
THCS12
THCS20
THCS28
TCB4SE
RPBA3
THD3
RHD3
TFBA3
RUP0
C3
RFHWM2
RHCS3
RHCS11
RHCS19
RHCS27
RCB3SE
THCS3
THCS11
THCS19
THCS27
TCB3SE
RPBA2
THD2
RHD2
TFBA2
RDN2
C2
RFHWM1
RHCS2
RHCS10
RHCS18
RHCS26
RCB2SE
THCS2
THCS10
THCS18
THCS26
TCB2SE
RPBA1
THD1
RHD1
TFBA1
RDN1
C1
RFHWM0
RHCS1
RHCS9
RHCS17
RHCS25
RCB1SE
THCS1
THCS9
THCS17
THCS25
TCB1SE
RPBA0
THD0
RHD0
TFBA0
RDN0
C0
TR.H2FC
RHCS7
RHCS15
RHCS23
RHCS31
RCB7SE
THCS7
THCS15
THCS23
THCS31
TCB7SE
RPBA6
THD6
RHD6
TFBA6
TC0
TR.H2RCS1
TR.H2RCS2
TR.H2RCS3
TR.H2RCS4
TR.H2RTSBS
TR.H2TCS1
TR.H2TCS2
TR.H2TCS3
TR.H2TCS4
TR.H2TTSBS
TR.H2RPBA
TR.H2TF
THD7
RHD7
TFBA7
TC1
TR.H2RF
TR.H2TFBA
TR.IBCC
0B6
h
0B7
h
C7
C6
TR.TCD1
0B8
h
C7
C6
C5
C4
C3
C2
C1
C0
TR.TCD2
0B9
h
0BA
h
0BB
h
0BC
h
0BD
h
0BE
h
0BF
h
0C0
h
C7
C6
C5
C4
C3
C2
C1
C0
TR.RUPCD1
TR.RUPCD2
TR.RDNCD1
TR.RDNCD2
TR.RSCC
C7
C6
C5
C4
C3
C2
C1
C0
C7
C6
C5
C4
C3
C2
C1
C0
C7
C6
C5
C4
C3
C2
C1
C0
—
—
—
—
—
RSC2
C2
RSC1
C1
RSC0
C0
C7
C6
C5
C4
C3
TR.RSCD1
TR.RSCD2
TR.RFDL
C7
C6
C5
C4
C3
C2
C1
C0
Bit Definitions Change With BOCC Setting. See Register Definition.
131 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0C1
h
0C2
h
0C3
h
0C3
h
0C5
h
0C6
h
TFDL7
TFDL6
RFDLM6
RFDLM6
—
TFDL5
TFDL4
TFDL3
TFDL2
TFDL1
TFDL0
TR.TFDL
TR.RFDLM1
TR.RFDLM2
Reserved
Reserved
TR.RAF
RFDLM7
RFDLM7
—
RFDLM5
RFDLM5
—
RFDLM4
RFDLM4
—
RFDLM3
RFDLM3
—
RFDLM2
RFDLM2
—
RFDLM1
RFDLM1
—
RFDLM0
RFDLM0
—
—
—
—
—
—
—
—
—
Si
0
0
1
1
0
1
1
0C7
h
0C8
h
0C9
h
0CA
h
0CB
h
0CC
h
0CD
h
0CE
h
Si
1
A
Sa4
Sa5
Sa6
Sa7
Sa8
TR.RNAF
TR.RSiAF
TR.RSiNAF
TR.RRA
SiF0
SiF2
SiF4
SiF6
SiF8
SiF10
SiF12
SiF14
SiF1
SiF3
SiF5
SiF7
SiF9
SiF11
SiF13
SiF15
RRAF1
RSa4F1
RSa5F1
RSa6F1
RSa7F1
RSa8F1
Si
RRAF3
RSa4F3
RSa5F3
RSa6F3
RSa7F3
RSa8F3
0
RRAF5
RSa4F5
RSa5F5
RSa6F5
RSa7F5
RSa8F5
0
RRAF7
RSa4F7
RSa5F7
RSa6F7
RSa7F7
RSa8F7
1
RRAF9
RSa4F9
RSa5F9
RSa6F9
RSa7F9
RSa8F9
1
RRAF11
RSa4F11
RSa5F11
RSa6F11
RSa7F11
RSa8F11
0
RRAF13
RSa4F13
RSa5F13
RSa6F13
RSa7F13
RSa8F13
1
RRAF15
RSa4F15
RSa5F15
RSa6F15
RSa7F15
RSa8F15
1
TR.RSa4
TR.RSa5
TR.RSa6
TR.RSa7
TR.RSa8
TR.TAF
0CF
h
0D0
h
0D1
h
0D2
h
0D3
h
0D4
h
0D5
h
0D6
h
0D7
h
0D8
h
Si
1
A
Sa4
Sa5
Sa6
Sa7
Sa8
TR.TNAF
TR.TSiAF
TR.TSiNAF
TR.TRA
TsiF0
TsiF1
TRAF1
TSa4F1
TSa5F1
TSa6F1
TSa7F1
TSa8F1
SiAF
TsiF2
TsiF3
TRAF3
TSa4F3
TSa5F3
TSa6F3
TSa7F3
TSa8F3
SiNAF
ACNT6
TsiF4
TsiF5
TRAF5
TSa4F5
TSa5F5
TSa6F5
TSa7F5
TSa8F5
RA
TsiF6
TsiF7
TRAF7
TSa4F7
TSa5F7
TSa6F7
TSa7F7
TSa8F7
Sa4
TsiF8
TsiF9
TRAF9
TSa4F9
TSa5F9
TSa6F9
TSa7F9
TSa8F9
Sa5
TsiF10
TsiF11
TRAF11
TSa4F11
TSa5F11
TSa6F11
TSa7F11
TSa8F11
Sa6
TsiF12
TsiF13
TRAF13
TSa4F13
TSa5F13
TSa6F13
TSa7F13
TSa8F13
Sa7
TsiF14
TSiF15
TRAF15
TSa4F15
TSa5F15
TSa6F15
TSa7F15
TSa8F15
Sa8
TR.TSa4
TR.TSa5
TR.TSa6
TR.TSa7
TR.TSa8
TR.TSACR
TR.BAWC
0D9
h
0DA
h
0DB
h
ACNT7
ACNT5
ACNT4
ACNT3
ACNT2
ACNT1
ACNT0
132 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
ADD
R
NAME
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0DC
h
0DD
h
0DE
h
0DF
h
0E0
h
0E1
h
0E2
h
0E3
h
0E4
h
0E5
h
0E6
h
0E7
h
0E8
h
0E9
h
0EA
h
0EB
h
RPAT7
RPAT6
RPAT14
RPAT22
RPAT30
TINV
EIB1
—
RPAT5
RPAT4
RPAT3
RPAT2
RPAT1
RPAT0
TR.BRP1
TR.BRP2
TR.BRP3
TR.BRP4
TR.BC1
RPAT15
RPAT23
RPAT31
TC
RPAT13
RPAT21
RPAT29
RINV
EIB0
—
RPAT12
RPAT20
RPAT28
PS2
RPAT11
RPAT19
RPAT27
PS1
RPAT10
RPAT18
RPAT26
PS0
RPAT9
RPAT17
RPAT25
LC
RPAT8
RPAT16
RPAT24
RESYNC
RPL0
—
EIB2
—
SBE
RPL3
—
RPL2
—
RPL1
—
TR.BC2
—
Reserved
TR.BBC1
TR.BBC2
TR.BBC3
TR.BBC4
TR.BEC1
TR.BEC2
TR.BEC3
TR.BIC
BBC7
BBC15
BBC23
BBC31
EC7
BBC6
BBC14
BBC22
BBC30
EC6
BBC5
BBC13
BBC21
BBC29
EC5
BBC4
BBC12
BBC20
BBC28
EC4
BBC3
BBC11
BBC19
BBC27
EC3
BBC2
BBC10
BBC18
BBC26
EC2
BBC1
BBC9
BBC17
BBC25
EC1
BBC0
BBC8
BBC16
BBC24
EC0
EC15
EC23
—
EC14
EC22
RFUS
—
EC13
EC21
—
EC12
EC20
TBAT
CE
EC11
EC19
TFUS
ER3
EC10
EC18
—
EC9
EC8
EC17
BERTDIR
ER1
EC16
BERTEN
ER0
WNOE
C7
—
ER2
TR.ERC
0EC
h
0ED
h
0EE
h
0EF
h
C6
C5
C4
C3
C2
C1
C0
TR.NOE1
TR.NOE2
TR.NOEL1
TR.NOEL2
—
—
—
—
—
—
C9
C8
C7
C6
C5
C4
C3
C2
C1
C0
—
—
—
—
—
—
C9
C8
133 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.2 Global Register Definitions for Ethernet Mapper
Functions contained in the global registers include: framer reset, LIU reset, device ID, and BERT interrupt status.
These registers are preserved to provide code compatibility with the multiport devices in this product family. The
global registers bit descriptions are presented below.
Register Name:
GL.IDRL
Register Description:
Register Address:
Global ID Low Register
00h
Bit #
Name
Default
7
ID07
0
6
ID06
0
5
ID05
1
4
ID04
1
3
ID03
0
2
ID02
0
1
ID01
0
0
ID00
0
Bit 7: ID07 Reserved for future use
Bit 6: ID06 Reserved for future use
Bit 5: ID05 If this bit is set the device contains a RMII interface
Bit 4: ID04 If this bit is set the device contains a MII interface
Bit 3: ID03 If this bit is set the device contains an Ethernet PHY
Bits 0-2: ID00-ID02 A three-bit count that is equal to 000b for the first die revision, and is incremented with each
successive die revision. May not match the two-letter die revision code on the top brand of the device.
Register Name:
GL.IDRH
Register Description:
Register Address:
Global ID High Register
01h
Bit #
Name
Default
7
ID15
0
6
ID14
0
5
ID13
0
4
ID12
0
3
ID11
0
2
ID10
0
1
ID09
1
0
ID08
0
Bits 5-7: ID13-15 Number of Ethernet ports in the device minus 1. (i.e. 000 = 1 Ethernet port)
Bit 4: ID12 If this bit is set the device has LIU functionality
Bit 3: ID11 If this bit is set the device has a framer
Bit 2: ID10 Reserved for future use
Bit 1: ID09 If this bit is set the device has HDLC or X.86 encapsulation
Bit 0: ID08 If this bit is set the device has inverse multiplexing functionality
134 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
GL.CR1
Register Description:
Register Address:
Global Control Register 1
02h
Bit #
Name
Default
7
-
6
-
5
-
4
-
3
-
2
1
INTM
0
0
RST
0
REF_CLKO
0
Bit 2: REF_CLKO OFF (REF_CLKO) This bit determines if the REF_CLKO is turned off
1 = REF_CLKO is disabled and outputs an active low signal.
0 = REF_CLKO is active and in accordance with RMII/MII Selection
Bit 1: INT pin mode (INTM) This bit determines the inactive mode of the INT pin. The INT pin always drives low
when active.
1 = Pin is high impedance when not active
0 = Pin drives high when not active
Bit 0: Reset (RST). When this bit is set to 1, all of the internal data path and status and control registers (except
this RST bit), on all ports, are reset to their default state. This bit must be set high for a minimum of 100ns.
0 = Normal operation
1 = Reset and force all internal registers to their default values
Register Name:
GL.BLR
Register Description:
Register Address:
Global BERT Connect Register
03h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
BLC1
0
Bit 0: BERT Connect 1 (BLC1) If this bit is set to 1, the BERT is connected to Serial Interface 1. The BERT
transmitter is connected to the transmit serial port and receive to receive serial port. When the BERT is connected,
normal data transfer is interrupted. Note that connecting the BERT overrides a connection to the Serial Interface, if
a connection exists. When the BERT is disconnected, the connection is restored.
135 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
GL.RTCAL
Register Description:
Register Address:
Global Receive and Transmit Serial Port Clock Activity Latched Status
04h
Bit #
Name
Default
7
-
-
6
-
-
5
-
-
4
3
-
-
2
-
-
1
-
-
0
RLCALS1
-
TLCALS1
-
Bit 4: Receive Serial Interface Clock Activity Latched Status 1 (RLCALS1) This bit is set to 1 if the receive
clock for Serial Interface 1 has activity. This bit is cleared upon read.
Bit 0: Transmit Serial Interface Clock Activity Latched Status 1 (TSCALS1) This bit is set to 1 if the transmit
clock for Serial Interface 1 has activity. This bit is cleared upon read.
Register Name:
GL.SRCALS
Register Description:
Register Address:
Global SDRAM Reference Clock Activity Latched Status
05h
Bit #
Name
Default
7
-
-
6
-
-
5
-
-
4
-
-
3
-
-
2
-
-
1
0
REFCLKS
-
SYSCLS
-
Bit 1: Reference Clock Activity Latched Status (REFCLKS) This bit is set to 1 if REF_CLK has activity. This bit
is cleared upon read.
Bit 0: System Clock Input Latched Status (SYSCLS) This bit is set to 1 if SYSCLKI has activity. This bit is
cleared upon read.
Register Name:
GL.LIE
Register Description:
Register Address:
Global Serial Interface Interrupt Enable
06h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
LIN1TIE
0
3
-
0
2
-
0
1
-
0
0
LIN1RIE
0
Bit 4: Serial Interface 1 TX Interrupt Enable (LINE1TIE) Setting this bit to 1 enables an interrupt on LIN1TIS
Bit 0: Serial Interface 1 RX Interrupt Enable (LINE1RIE) Setting this bit to 1 enables an interrupt on LIN1RIS
136 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
GL.LIS
Register Description:
Register Address:
Global Serial Interface Interrupt Status
07h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
LIN1TIS
0
3
-
0
2
-
0
1
-
0
0
LIN1RIS
0
Bit 4: Serial Interface 1 TX Interrupt Status (LINE1TIS) This bit is set if Serial Interface 1 Transmit has an
enabled interrupt generating event. Serial Interface interrupts consist of HDLC interrupts and X.86 interrupts.
Bit 0: Serial Interface 1 RX Interrupt Status (LINER1IS) This bit is set if Serial Interface 1 Receive has an
enabled interrupt generating event. Serial Interface interrupts consist of HDLC interrupts and X.86 interrupts.
Register Name:
GL.SIE
Register Description:
Register Address:
Global Ethernet Interface Interrupt Enable
08h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
SUB1IE
0
Bit 0: Ethernet Interface 1 Interrupt Enable (SUB1IE) Setting this bit to 1 enables an interrupt on SUB1S.
Register Name:
GL.SIS
Register Description:
Register Address:
Global Ethernet Interface Interrupt Status
09h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
SUB1IS
0
Bit 0: Ethernet Interface 1 Interrupt Status (SUB1IS) This bit is set to 1 if Ethernet Interface 1 has an enabled
interrupt generating event. The Ethernet Interface consists of the MAC and The RMII/MII port.
137 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
GL.TRQIE
Register Description:
Register Address:
Global Transmit Receive Queue Interrupt Enable
0Ah
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
TQ1IE
0
3
-
0
2
-
0
1
-
0
0
RQ1IE
0
Bit 4: Transmit Queue 1 Interrupt Enable (TQ1IE) Setting this bit to 1 enables an interrupt on TQ1IS.
Bit 0: Receive Queue 1 Interrupt Enable (RQ1IE) Setting this bit to 1 enables an interrupt on RQ1IS.
Register Name:
GL.TRQIS
Register Description:
Register Address:
Global Transmit Receive Queue Interrupt Status
0Bh
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
TQ1IS
0
3
-
0
2
-
0
1
-
0
0
RQ1IS
0
Bit 4: Transmit Queue 1 Interrupt Enable (TQ1IS) If this bit is set to 1, the Transmit Queue 1 has interrupt status
event. Transmit queue events are transmit queue crossing thresholds and queue overflows.
Bit 0: Receive Queue 1 Interrupt Status (RQ1IS) If this bit is set to 1, the Receive Queue 1 has interrupt status
event. Receive queue events are transmit queue crossing thresholds and queue overflows.
Register Name:
GL.BIE
Register Description:
Register Address:
Global BERT Interrupt Enable
0Ch
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
BIE
0
Bit 0: BERT Interrupt Enable (BIE) Setting this bit to 1 enables an interrupt on BIS.
138 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
GL.BIS
Register Description:
Register Address:
Global BERT Interrupt Status
0Dh
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
BIS
0
Bit 0: BERT Interrupt Status (BIS) This bit is set to 1 if the BERT has an enabled interrupt generating event.
Register Name:
GL.CON1
Register Description:
Register Address:
Connection Register for Ethernet Interface 1
0Eh
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
LINE1[0]
1
Bit 0: LINE1[0] This bit is preserved to provide software compatibility with multiport devices. The LINE1[0] bit
selects the Ethernet port that is to be connected to the Serial Interface. Note that bidirectional connection is
assumed between the Serial and Ethernet Interfaces. The connection register and corresponding queue size must
be defined for proper operation. Writing a 0 to this register will disconnect the connection. When a connection is
disconnected, “1”s are sourced to the Serial Interface transmit and to the HDLC receiver and the clocks to the
HDLC transmitter/receiver are disabled.
139 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
GL.C1QPR
Register Description:
Register Address:
Connection 1 Queue Pointer Reset
12h
Bit #
7
6
5
4
3
2
1
0
Name
Default
-
0
-
0
-
0
-
0
C1MRPR
0
C1HWPR
0
C1MHPR
0
C1HRPR
0
Bit 3: MAC Read Pointer Reset (C1MRPR) Setting this bit to 1 resets the receive queue read pointer for
connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear
the bit before subsequent reset operations.
Bit 2: HDLC Write Pointer Reset (C1HWPR) Setting this bit to 1 resets the receive queue write pointer for
connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear
the bit before subsequent reset operations.
Bit 1: HDLC Read Pointer Reset (C1MHPR) Setting this bit to 1 resets the transmit queue read pointer for
connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear
the bit before subsequent reset operations.
Bit 0: MAC Transmit Write Pointer Reset (C1HRPR) Setting this bit to 1 resets the transmit queue write pointer
for connection 1. This queue pointer must be reset after a disconnect and before a connection. The user must clear
the bit before subsequent reset operations.
Register Name:
Register Description:
Register Address:
GL.BISTEN
BIST Enable
20h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
BISTE
0
Bit 0: BIST Enable (BISTE) If this bit is set the DS33R11 performs BIST test on the SDRAM. Normal data
communication is halted while BIST enable is high. The user must reset the DS33R11 after completion of BIST test
before normal dataflow can begin.
140 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
Register Description:
Register Address:
GL.BISTPF
BIST Pass-Fail
21h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
BISTDN
0
0
BISTPF
0
Bit 1: BIST DONE (BISTDN) If this bit is set to 1, the DS33R11 has completed the BIST Test initiated by BISTE.
The pass fail result is available in BISTPF.
Bit 0: BIST Pass-Fail (BISTPF) This bit is equal to 0 after the DS33R11 performs BIST testing on the SDRAM and
the test passes. This bit is set to 1 if the test failed. This bit is valid only after the BIST test is complete and the
BIST DN bit is set. If set this bit can only be cleared by resetting the DS33R11.
Register Name:
GL.SDMODE1
Register Description:
Register Address:
Global SDRAM Mode Register 1
3Ah
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
WT
0
2
BL2
0
1
BL1
1
0
BL0
1
Bit 3: Wrap Type (WT) This bit is used to configure the wrap mode.
0 = Sequential
1 = Interleave
Bits 0- 2: Burst Length 0 through 2 (BL0 – BL2) These bits are used to determine the Burst Length.
Note: This register has a nonzero default value. This should be taken into consideration when initializing
the device.
Note: After changing the value of this register, the user must toggle the GL.SDMODEWS.SDMW bit to write
the new values to the SDRAM.
141 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
GL.SDMODE2
Register Description:
Register Address:
Global SDRAM Mode Register 2
3Bh
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
LTMOD2
0
1
LTMOD1
1
0
LTMOD0
0
Bits 0 - 2: CAS Latency Mode (LTMOD0 - LTMOD2) These bits are used to setup CAS Latency
Note: Only CAS Latency of 2 or 3 is allowed
Note: This register has a nonzero default value. This should be taken into consideration when initializing
the device.
Note: After changing the value of this register, the user must toggle the GL.SDMODEWS.SDMW bit to write
the new values to the SDRAM.
Register Name:
GL.SDMODEWS
Register Description:
Register Address:
Global SDRAM Mode Register Write Status
3Ch
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
SDMW
0
Bit 0: SDRAM Mode Write (SDMW) Setting this bit to 1 will write the current values of the mode control and
refresh time control registers to the SDRAM. The user must clear this bit and set it again for subsequent write
operations.
Register Name:
GL.SDRFTC
Register Description
Register Address:
Global SDRAM Refresh Time Control
3Dh
Bit #
Name
Default
7
SREFT7
0
6
SREFT6
1
5
SREFT5
0
4
SREFT4
0
3
SREFT3
0
2
SREFT2
1
1
SREFT1
1
0
SREFT0
0
Bits 0 - 7: SDRAM Refresh Time Control (SREFT0 – SREFT7) These 8 bits are used to control the SDRAM
refresh frequency. The refresh rate will be equal to this register value x 8 x 100MHz.
Note: This register has a nonzero default value. This should be taken into consideration when initializing
the device.
Note: After changing the value of this register, the user must toggle the GL.SDMODEWS.SDMW bit to write
the new values to the SDRAM.
142 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.3 Arbiter Registers
The Arbiter manages the transport between the Ethernet port and the Serial Interface. It is responsible for queuing
and dequeuing data to an external SDRAM. The arbiter handles requests from the HDLC and MAC to transfer data
to/from the SDRAM. The base address of the Arbiter register space is 0040h.
11.3.1 Arbiter Register Bit Descriptions
Register Name:
AR.RQSC1
Register Description:
Register Address:
Arbiter Receive Queue Size Connection
40h
Bit #
Name
Default
7
RQSC7
0
6
RQSC6
0
5
RQSC5
1
4
RQSC4
1
3
RQSC3
1
2
RQSC2
1
1
RQSC1
0
0
RQSC0
1
Bits 0-7: Receive Queue Size (RQSC[0:7]) These 7 bits of the size of receive queue associated with the
connection. Receive queue is for data arriving from the MAC to be sent to the WAN. The Queue address size is
defined in increments of 32 x 2048 bytes. The queue size is AR.RQSC1 multiplied by 32 to determine the number
of 2048 byte packets that can be stored in the queue. This queue is constructed in the external SDRAM. Note:
Queue size of 0 is not allowed and should never be set.
Register Name:
AR.TQSC1
Register Description:
Register Address:
Arbiter Transmit Queue Size Connection 1
41h
Bit #
Name
Default
7
TQSC7
0
6
TQSC6
0
5
TQSC5
0
4
TQSC4
0
3
TQSC3
0
2
TQSC2
0
1
TQSC1
1
0
TQSC0
1
Bits 0-7: Transmit Queue Size (TQSC[0:7]) This is size of transmit queue associated with the connection. The
queue address size is defined in increments of 32 packets. The range of bytes will depend on the external SDRAM
connected to the DS33R11. Transmit queue is the data queue for data arriving on the WAN that is sent to the
MAC. Note that queue size of 0 is not allowed and should never be set.
143 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.4 BERT Registers
Register Name:
BCR
Register Description:
Register Address:
BERT Control Register
80h
Bit #
Name
Default
7
-
0
6
PMU
0
5
RNPL
0
4
RPIC
0
3
MPR
0
2
APRD
0
1
TNPL
0
0
TPIC
0
Bit 7: This bit must be kept low for proper operation.
Bit 6: Performance Monitoring Update (PMU) This bit causes a performance monitoring update to be initiated. A
0 to 1 transition causes the performance monitoring registers to be updated with the latest data, and the counters
reset (0 or 1). For a second performance monitoring update to be initiated, this bit must be set to 0, and back to 1.
If PMU goes low before the PMS bit goes high, an update might not be performed.
Bit 5: Receive New Pattern Load (RNPL) A zero to one transition of this bit will cause the programmed test
pattern (QRSS, PTS, PLF [4:0}, PTF [4:0], and BSP [31:0]) to be loaded in to the receive pattern generator. This bit
must be changed to zero and back to one for another pattern to be loaded. Loading a new pattern will forces the
receive pattern generator out of the “Sync” state which causes a resynchronization to be initiated. Note: QRSS,
PTS, PLF [4:0}, PTF [4:0], and BSP [31:0] must not change from the time this bit transitions from 0 to 1 until four
RCLKI clock cycles after this bit transitions from 0 to 1.
Bit 4: Receive Pattern Inversion Control (RPIC) When 0, the receive incoming data stream is not altered. When
1, the receive incoming data stream is inverted.
Bit 3: Manual Pattern Resynchronization (MPR) A zero to one transition of this bit will cause the receive pattern
generator to resynchronize to the incoming pattern. This bit must be changed to zero and back to one for another
resynchronization to be initiated. Note: A manual resynchronization forces the receive pattern generator out of the
“Sync” state.
Bit 2: Automatic Pattern Resynchronization Disable (APRD) When 0, the receive pattern generator will
automatically resynchronize to the incoming pattern if six or more times during the current 64-bit window the
incoming data stream bit and the receive pattern generator output bit did not match. When 1, the receive pattern
generator will not automatically resynchronize to the incoming pattern. Note: Automatic synchronization is
prevented by not allowing the receive pattern generator to automatically exit the “Sync” state.
Bit 1: Transmit New Pattern Load (TNPL) A zero to one transition of this bit will cause the programmed test
pattern (QRSS, PTS, PLF[4:0}, PTF[4:0], and BSP[31:0]) to be loaded in to the transmit pattern generator. This bit
must be changed to zero and back to one for another pattern to be loaded. Note: QRSS, PTS, PLF[4:0}, PTF[4:0],
and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four TCLKE clock cycles after this
bit transitions from 0 to 1.
Bit 0: Transmit Pattern Inversion Control (TPIC) When 0, the transmit outgoing data stream is not altered. When
1, the transmit outgoing data stream is inverted.
144 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
BPCLR
Register Description:
Register Address:
BERT Pattern Configuration Low Register
82h
Bit #
Name
Default
7
-
0
6
QRSS
0
5
PTS
0
4
PLF4
0
3
PLF3
0
2
PLF2
0
1
PLF1
0
0
PLF0
0
Bit 6: QRSS Enable (QRSS) When 0, the pattern generator configuration is controlled by PTS, PLF[0:4], and
PTF[0:4], and BSP[0:31]. When 1, the pattern generator configuration is forced to a QRSS pattern with a
generating polynomial of x20 + x17 + 1. The output of the pattern generator is forced to one if the next fourteen
output bits are all zero.
Bit 5: Pattern Type Select (PTS) When 0, the pattern is a PRBS pattern. When 1, the pattern is a repetitive
pattern.
Register Name:
BPCHR
Register Description:
Register Address:
BERT Pattern Configuration High Register
83h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
PTF4
0
3
PTF3
0
2
PTF2
0
1
PTF1
0
0
PTF0
0
Bits 4 to 0: Pattern Tap Feedback (PTF[4:0]) These five bits control the PRBS “tap” feedback of the pattern
generator. The “tap” feedback is from bit y of the pattern generator (y = PTF[4:0] +1). These bits are ignored when
programmed for a repetitive pattern. For a PRBS signal, the feedback is an XOR of bit n and bit y. The values
145 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
BSPB0R
Register Description:
Register Address:
BERT Pattern Byte0 Register
84h
Bit #
Name
Default
7
BSP7
0
6
BSP6
0
5
BSP5
0
4
BSP4
0
3
BSP3
0
2
BSP2
0
1
BSP1
0
0
BSP0
0
Bits 0 to 7: BERT Pattern (BSP[7:0]) Lower eight bits of 32 bits. Register description follows next register.
Register Name:
BSPB1R
Register Description:
Register Address:
BERT Pattern Byte 1 Register
85h
Bit #
Name
Default
7
BSP15
0
6
BSP14
0
5
BSP13
0
4
BSP12
0
3
BSP11
0
2
BSP10
0
1
BSP9
0
0
BSP8
0
Bits 0 to 7: BERT Pattern (BSP[15:8]) 8 bits of 32 bits. Register description below.
Register Name:
BSPB2R
Register Description:
Register Address:
BERT Pattern Byte2 Register
86h
Bit #
Name
Default
7
BSP23
0
6
BSP22
0
5
BSP21
0
4
BSP20
0
3
BSP19
0
2
BSP18
0
1
BSP17
0
0
BSP16
0
Bits 0 to 7: BERT Pattern (BSP[23:16]) 8 bits of 32 bits. Register description below.
Register Name:
BSPB3R
Register Description:
Register Address:
BERT Seed/Pattern Byte3 Register
87h
Bit #
Name
Default
7
BSP31
0
6
BSP30
0
5
BSP29
0
4
BSP28
0
3
BSP27
0
2
BSP26
0
1
BSP25
0
0
BSP24
0
Bits 0 to 8: BERT Pattern (BSP[31:24]) Upper 8 bits of 32 bits. Register description below.
BERT Pattern (BSP[31:0]) These 32 bits are the programmable seed for a transmit PRBS pattern, or the
programmable pattern for a transmit or receive repetitive pattern. BSP(31) is the first bit output on the transmit side
for a 32-bit repetitive pattern or 32-bit length PRBS. BSP(31) is the first bit input on the receive side for a 32-bit
repetitive pattern.
146 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TEICR
Register Description:
Register Address:
Transmit Error Insertion Control Register
88h
Bit #
Name
Default
7
-
0
6
-
0
5
TIER2
0
4
TIER1
0
3
TIER0
0
2
BEI
0
1
TSEI
0
0
-
0
Bits 3 to 5: Transmit Error Insertion Rate (TEIR[2:0]) These three bits indicate the rate at which errors are
inserted in the output data stream. One out of every 10n bits is inverted. TEIR[2:0] is the value n. A TEIR[2:0] value
of 0 disables error insertion at a specific rate. A TEIR[2:0] value of 1 result in every 10th bit being inverted. A
TEIR[2:0] value of 2 results in every 100th bit being inverted. Error insertion starts when this register is written to
with a TEIR[2:0] value that is nonzero. If this register is written to during the middle of an error insertion process,
the new error rate is started after the next error is inserted.
Bit 2: Bit Error Insertion Enable (BEI) When 0, single bit error insertion is disabled. When 1, single bit error
insertion is enabled.
Bit 1: Transmit Single Error Insert (TSEI) This bit causes a bit error to be inserted in the transmit data stream if
and single bit error insertion is enabled. A 0 to 1 transition causes a single bit error to be inserted. For a second bit
error to be inserted, this bit must be set to 0, and back to 1. Note: If this bit transitions more than once between
error insertion opportunities, only one error is inserted.
All other bits in this register besides BEI and TSEI and TIER must be reset to 0 for proper operation.
Register Name:
BSR
Register Description:
Register Address:
BERT Status Register
8Ch
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
PMS
0
2
-
0
1
BEC
0
0
OOS
0
Bit 3: Performance Monitoring Update Status (PMS) This bit indicates the status of the receive performance
monitoring register (counters) update. This bit will transition from low to high when the update is completed. PMS is
asynchronously forced low when the PMU bit goes low. TCLKE and RCLKI must be present.
Bit 1: Bit Error Count (BEC) When 0, the bit error count is zero. When 1, the bit error count is one or more.
Bit 0: Out Of Synchronization (OOS) When 0, the receive pattern generator is synchronized to the incoming
pattern. When 1, the receive pattern generator is not synchronized to the incoming pattern.
147 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
BSRL
Register Description:
Register Address:
BERT Status Register Latched
8Eh
Bit #
Name
Default
7
-
-
6
-
-
5
-
-
4
-
-
3
PMSL
-
2
BEL
-
1
BECL
-
0
OOSL
-
Bit 3: Performance Monitor Update Status Latched (PMSL) This bit is set when the PMS bit transitions from 0
to 1.
Bit 2: Bit Error Detected Latched (BEL) This bit is set when a bit error is detected.
Bit 1: Bit Error Count Latched (BECL) This bit is set when the BEC bit transitions from 0 to 1.
Bit 0: Out Of Synchronization Latched (OOSL) This bit is set when the OOS bit changes state.
Register Name:
BSRIE
Register Description:
Register Address:
BERT Status Register Interrupt Enable
90h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
PMSIE
0
2
BEIE
0
1
BECIE
0
0
OOSIE
0
Bit 3: Performance Monitoring Update Status Interrupt Enable (PMSIE) This bit enables an interrupt if the
PMSL bit is set.
0 = interrupt disabled
1 = interrupt enabled
Bit 2: Bit Error Interrupt Enable (BEIE) This bit enables an interrupt if the BEL bit is set.
0 = interrupt disabled
1 = interrupt enabled
Bit 1: Bit Error Count Interrupt Enable (BECIE) This bit enables an interrupt if the BECL bit is set.
0 = interrupt disabled
1 = interrupt enabled
Bit 0: Out Of Synchronization Interrupt Enable (OOSIE) This bit enables an interrupt if the OOSL bit is set.
0 = interrupt disabled
1 = interrupt enabled
148 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
RBECB0R
Register Description:
Register Address:
Receive Bit Error Count Byte 0 Register
94h
Bit #
Name
Default
7
BEC7
0
6
BEC6
0
5
BEC5
0
4
BEC4
0
3
BEC3
0
2
BEC2
0
1
BEC1
0
0
BEC0
0
Bits 0 - 7: Bit Error Count (BEC[0:7]) Lower eight bits of 24 bits. Register description below.
Register Name:
RBECB1R
Register Description:
Register Address:
Receive Bit Error Count Byte 1 Register
95h
Bit #
Name
Default
7
BEC15
0
6
BEC14
0
5
BEC13
0
4
BEC12
0
3
BEC11
0
2
BEC10
0
1
BEC9
0
0
BEC8
0
Bits 0 - 7: Bit Error Count (BEC[8:15]) Eight bits of a 24 bit value. Register description below.
Register Name:
RBECR2
Register Description:
Register Address:
Receive Bit Error Count Byte 2 Register
96h
Bit #
Name
Default
7
BEC23
0
6
BEC22
0
5
BEC21
0
4
BEC20
0
3
BEC19
0
2
BEC18
0
1
BEC17
0
0
BEC16
0
Bits 0 - 7: Bit Error Count (BEC[16:23]) Upper 8-bits of the register.
Bit Error Count (BEC[0:23]) These twenty-four bits indicate the number of bit errors detected in the incoming data
stream. This count stops incrementing when it reaches a count of FF FFFFh. The associated bit error counter will
not incremented when an OOS condition exists.
Register Name:
RBCB0
Register Description:
Register Address:
Receive Bit Count Byte 0 Register
98h
Bit #
Name
Default
7
BC7
0
6
BC6
0
5
BC5
0
4
BC4
0
3
BC3
0
2
BC2
0
1
BC1
0
0
BC0
0
Bits 0 - 7: Bit Count (BC[0:7]) Eight bits of a 32 bit value. Register description below.
149 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
RBCB1
Register Description:
Register Address:
Receive Bit Count Byte 1 Register #1
99h
Bit #
Name
Default
7
BC15
0
6
BC14
0
5
BC13
0
4
BC12
0
3
BC11
0
2
BC10
0
1
BC9
0
0
BC8
0
Bits 0 - 7: Bit Count (BC[8:15]) Eight bits of a 32 bit value. Register description below.
Register Name:
RBCB2
Register Description:
Register Address:
Receive Bit Count Byte 2 Register
9Ah
Bit #
Name
Default
7
BC23
0
6
BC22
0
5
BC21
0
4
BC20
0
3
BC19
0
2
BC18
0
1
BC17
0
0
BC16
0
Bits 0 - 7: Bit Count (BC[16:23]) Eight bits of a 32 bit value. Register description below.
Register Name:
RBCB3
Register Description:
Register Address:
Receive Bit Count Byte 3 Register
9Bh
Bit #
7
BC31
0
6
BC30
0
5
BC29
0
4
BC28
0
3
BC27
0
2
BC26
0
1
BC25
0
0
BC24
0
Name
Default
Bits 0 - 7: Bit Count (BC[24:31]) Upper 8-bits of the register.
Bit Count (BC[0:31]) These thirty-two bits indicate the number of bits in the incoming data stream. This count
stops incrementing when it reaches a count of FFFF FFFFh. The associated bit counter will not incremented when
an OOS condition exists.
150 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.5 Serial Interface Registers
The Serial Interface contains the Serial HDLC transport circuitry and the associated serial port. The Serial Interface
register map consists of registers that are common functions, transmit functions, and receive functions.
Bits that are underlined are read-only; all other bits can be written. All reserved registers and bits with “-“
designation should be written to zero, unless specifically noted in the register definition. When read, the information
from reserved registers and bits designated with “-“ should be discarded.
Counter registers are updated by asserting (low to high transition) the associated performance monitoring update
signal (xxPMU). During the counter register update process, the associated performance monitoring status signal
(xxPMS) is deasserted. The counter register update process consists of loading the counter register with the
current count, resetting the counter, forcing the zero count status indication low for one clock cycle, and then
asserting xxPMS. No events are missed during this update procedure.
A latched bit is set when the associated event occurs, and remains set until it is cleared by reading. Once cleared,
a latched bit will not be set again until the associated event occurs again. Reserved configuration bits and registers
should be written to zero.
11.5.1 Serial Interface Transmit and Common Registers
Serial Interface Transmit Registers are used to control the HDLC transmitter associated with each Serial Interface.
The register map is shown in the following Table. Note that throughout this document the HDLC Processor is also
referred to as a “packet processor”.
11.5.1.1 Serial Interface Transmit Register Bit Descriptions
Register Name:
LI.TSLCR
Register Description:
Register Address:
Transmit Serial Interface Configuration Register
0C0h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
TDENPLT
0
Bit 0: Transmit Data Enable Polarity (TDENPLT) If set to 1, TDEN is active low for enable. In the default mode,
when TDEN is logic high, the data is enabled and output by the DS33R11.
Register Name:
LI.RSTPD
Register Description:
Register Address:
Serial Interface Reset Register
0C1h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
RESET
0
0
-
0
Bit 1: RESET If this bit set to 1, the Data Path and Control and Status for this interface are reset. The Serial
Interface is held in Reset as long as this bit is high. This bit must be high for a minimum of 200ns for a valid reset
to occur.
151 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.LPBK
Register Description:
Register Address:
Serial Interface Loopback Control Register
0C2h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
QLP
0
Bit 0: Queue Loopback Enable (QLP) If this bit set to 1, data received on the Serial Interface is looped back to
the Serial Interface transmitter. Received data will not be sent from the Serial Interface to the Ethernet Interface.
Buffered packet data will remain in queue until the loopback is removed.
11.5.1.2 Transmit HDLC Processor Register Bit Descriptions
Register Name:
LI.TPPCL
Register Description:
Register Address:
Transmit Packet Processor Control Low Register
0C4h
Bit #
Name
Default
7
-
0
6
-
0
5
TFAD
0
4
TF16
0
3
TIFV
0
2
TSD
0
1
TBRE
0
0
TIAEI
0
Note: The user should take care not to modify this register value during packet error insertion.
Bits 5 - 6: Transmit FCS Append Disable (TFAD) – This bit controls whether or not an FCS is appended to the
end of each packet. When equal to 0, the calculated FCS bytes are appended to packets. When set to 1, packets
are transmitted without FCS. In X.86 Mode, FCS is always 32 bits and is always appended to the packet.
Bit 4: Transmit FCS-16 Enable (TF16) – When 0, the FCS processing uses a 32-bit FCS. When 1, the FCS
processing uses a 16-bit FCS. In X.86 Mode, 32-bit FCS processing is always enabled, regardless of this bit.
Bit 3: Transmit Bit Synchronous Inter-frame Fill Value (TIFV) – When 0, inter-frame fill is done with the flag
sequence (7Eh). When 1, inter-frame fill is done with all '1's (FFh). This bit is ignored in X.86 mode and the
interframe flag is always 7E.
Bit 2: Transmit Scrambling Disable (TSD) – When equal to 0, X43+1 scrambling is performed. When set to 1,
scrambling is disabled.
Bit 1: Transmit Bit Reordering Enable (TBRE) – When equal to 0, bit reordering is disabled (The first bit
transmitted is from the MSB of the transmit FIFO byte TFD [7]). When set to 1, bit reordering is enabled (The first
bit transmitted is from the LSB of the transmit FIFO byte TFD [0]).
Bit 0: Transmit Initiate Automatic Error Insertion (TIAEI) – This write-only bit initiates error insertion. See the
LI.TEPHC register definition for details of usage.
152 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.TIFGC
Register Description:
Register Address:
Transmit Inter-Frame Gapping Control Register
0C5h
Bit #
Name
Default
7
TIFG7
0
6
TIFG6
0
5
TIFG5
0
4
TIFG4
0
3
TIFG3
0
2
TIFG2
0
1
TIFG1
0
0
TIFG0
1
Bits 0 - 7: Transmit Inter-Frame Gapping (TIFG[7:0]) – These eight bits indicate the number of additional flags
and bytes of inter-frame fill to be inserted between packets. The number of flags and bytes of inter-frame fill
between packets is at least the value of TIFG[7:0] plus 1. Note: If inter-frame fill is set to all 1’s, a TFIG value of 2
or 3 will result in a flag, two bytes of 1’s, and an additional flag between packets.
Register Name:
LI.TEPLC
Register Description:
Register Address:
Transmit Errored Packet Low Control Register
0C6h
Bit #
Name
Default
7
TPEN7
0
6
TPEN6
0
5
TPEN5
0
4
TPEN4
0
3
TPEN3
0
2
TPEN2
0
1
TPEN1
0
0
TPEN0
0
Bits 0 – 7: Transmit Errored Packet Insertion Number (TPEN[7:0]) – These eight bits indicate the total number
of errored packets to be transmitted when triggered by TIAEI. Error insertion will end after this number of errored
packets have been transmitted. A value of FFh results in continuous errored packet insertion at the specified rate.
153 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.TEPHC
Register Description:
Register Address:
Transmit Errored Packet High Control Register
0C7h
Bit #
Name
Default
7
MEIMS
0
6
TPER6
0
5
TPER5
0
4
TPER4
0
3
TPER3
0
2
TPER2
0
1
TPER1
0
0
TPER0
0
Bit 7: Manual Error Insert Mode Select (MEIMS) – When 0, the transmit manual error insertion signal (TMEI) will
not cause errors to be inserted. When 1, TMEI will cause an error to be inserted when it transitions from a 0 to a 1.
Note: Enabling TMEI does not disable error insertion using TCER[6:0] and TCEN[7:0].
Bits 0 – 6: Transmit Errored Packet Insertion Rate (TPER[6:0]) – These seven bits indicate the rate at which
errored packets are to be output. One out of every x * 10y packets is to be an errored packet. TPER[3:0] is the
value x, and TPER[6:4] is the value y which has a maximum value of 6. If TPER[3:0] has a value of 0h errored
packet insertion is disabled. If TPER[6:4] has a value of 6xh or 7xh the errored packet rate is x * 106. A TPER[6:0]
value of 01h results in every packet being errored. A TPER[6:0] value of 0Fh results in every 15th packet being
errored. A TPER[6:0] value of 11h results in every 10th packet being errored.
To initiate automatic error insertion, use the following routine:
1) Configure LI.TEPLC and LI.TEPHC for the desired error insertion mode.
2) Write the LI.TPPCL.TIAEI bit to 1. Note that this bit is write-only.
3) If not using continuous error insertion (LI.TPELC is not equal to FFh), the user should monitor the
LI.TPPSR.TEPF bit for completion of the error insertion. If interrupt on completion of error insertion is
enabled (LI.TPPSRIE.TEPFIE = 1), the user only needs to wait for the interrupt condition.
4) Proceed with the cleanup routine listed below.
Cleanup routine:
1) Write LI.TEPLC and LI.TEPHC each to 00h.
2) Write the LI.TPPCL.TIAEI bit to 0.
154 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.TPPSR
Register Description:
Register Address:
Transmit Packet Processor Status Register
0C8h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
TEPF
0
Bit 0: Transmit Errored Packet Insertion Finished (TEPF) – This bit is set when the number of errored packets
indicated by the TPEN[7:0] bits in the TEPC register have been transmitted. This bit is cleared when errored
packet insertion is disabled, or a new errored packet insertion process is initiated.
Register Name:
LI.TPPSRL
Register Description:
Register Address:
Transmit Packet Processor Status Register Latched
0C9h
Bit #
Name
Default
7
-
-
6
-
-
5
-
-
4
-
-
3
-
-
2
-
-
1
-
-
0
TEPFL
-
Bit 0: Transmit Errored Packet Insertion Finished Latched (TEPFL) – This bit is set when the TEPF bit in the
TPPSR register transitions from zero to one.
Register Name:
LI.TPPSRIE
Register Description:
Register Address:
Transmit Packet Processor Status Register Interrupt Enable
0CAh
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
TEPFIE
0
Bit 0: Transmit Errored Packet Insertion Finished Interrupt Enable (TEPFIE) – This bit enables an interrupt if
the TEPFL bit in the LI.TPPSRL register is set.
0 = interrupt disabled
1 = interrupt enabled
155 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.TPCR0
Register Description:
Transmit Packet Count Byte 0
Register Address:
0CCh
Bit #
Name
Default
7
TPC7
0
6
TPC6
0
5
TPC5
0
4
TPC4
0
3
TPC3
0
2
TPC2
0
1
TPC1
0
0
TPC0
0
Bits 0 – 7: Transmit Packet Count (TPC[7:0]) – Eight bits of 24 bit value. Register description below.
Register Name:
LI.TPCR1
Register Description:
Register Address:
Transmit Packet Count Byte 1
0CDh
Bit #
Name
Default
7
TPC15
0
6
TPC14
0
5
TPC13
0
4
TPC12
0
3
TPC11
0
2
TPC10
0
1
TPC9
0
0
TPC8
0
Bits 0 – 7: Transmit Packet Count (TPC[15:8]) – Eight bits of 24 bit value. Register description below.
Register Name:
LI.TPCR2
Register Description:
Register Address:
Transmit Packet Count Byte 2
0CEh
Bit #
Name
Default
7
TPC23
0
6
TPC22
0
5
TPC21
0
4
TPC20
0
3
TPC19
0
2
TPC18
0
1
TPC17
0
0
TPC16
0
Bits 0 – 7: Transmit Packet Count (TPC[23:16]) – These twenty-four bits indicate the number of packets
extracted from the Transmit FIFO and output in the outgoing data stream.
156 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.TBCR0
Register Description:
Register Address:
Transmit Byte Count Byte 0
0D0h
Bit #
Name
Default
7
TBC7
0
6
TBC6
0
5
TBC5
0
4
TBC4
0
3
TBC3
0
2
TBC2
0
1
TBC1
0
0
TBC0
0
Bits 0 – 7: Transmit Byte Count (TBC[0:7]) – Eight bits of 32 bit value. Register description below.
Register Name:
LI.TBCR1
Register Description:
Register Address:
Transmit Byte Count Byte 1
0D1h
Bit #
Name
Default
7
TBC15
0
6
TBC14
0
5
TBC13
0
4
TBC12
0
3
TBC11
0
2
TBC10
0
1
TBC9
0
0
TBC8
0
Bits 0 – 7: Transmit Byte Count (TBC[15:8]) - Eight bits of 32 bit value. Register description below.
Register Name:
LI.TBCR2
Register Description:
Register Address:
Transmit Byte Count Byte 2
0D2h
Bit #
Name
Default
7
TBC23
0
6
TBC22
0
5
TBC21
0
4
TBC20
0
3
TBC19
0
2
TBC18
0
1
TBC17
0
0
TBC16
0
Bits 0 – 7: Transmit Byte Count (TBC[23:16]) - Eight bits of 32 bit value. Register description below.
Register Name:
LI.TBCR3
Register Description:
Register Address:
Transmit Byte Count Byte 3
0D3h
Bit #
Name
Default
7
TBC31
0
6
TBC30
0
5
TBC29
0
4
TBC28
0
3
TBC27
0
2
TBC26
0
1
TBC25
0
0
TBC24
0
Bits 0 – 7: Transmit Byte Count (TBC[31:24]) – These thirty-two bits indicate the number of packet bytes
inserted in the outgoing data stream.
Register Name:
LI.TMEI
Register Description:
Register Address:
Transmit Manual Error Insertion
0D4h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
TMEI
0
Bit 0: Transmit Manual Error Insertion (TMEI) A zero to one transition will insert a single error in the Transmit
direction.
157 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.THPMUU
Register Description:
Register Address:
Serial Interface Transmit HDLC PMU Update Register
0D6h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
TPMUU
0
Bit 0: Transmit PMU Update (TPMUU) This signal causes the transmit cell/packet processor block performance
monitoring registers (counters) to be updated. A 0 to 1 transition causes the performance monitoring registers to be
updated with the latest data, and the counters reset (0 or 1). This update updates performance monitoring counters
for the Serial Interface.
Register Name:
LI.THPMUS
Register Description:
Register Address:
Serial Interface Transmit HDLC PMU Update Status Register
0D7h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
TPMUS
0
Bit 0: Transmit PMU Update Status (TPMUS) This bit is set when the Transmit PMU Update is completed. This
bit is cleared when TPMUU is reset.
158 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.5.2 X.86 Registers
X.86 transmit and common registers are used to control the operation of the X.86 encoder and decoder.
Register Name:
LI.TX86EDE
Register Description:
Register Address:
X.86 Encoding Decoding Enable
0D8h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
X86ED
0
Bit 0: X.86 Encoding Decoding (X86ED) If this bit is set to 1, X.86 encoding and decoding is enabled for the
Transmit and Receive paths. The MAC Frame is encapsulated in the X.86 Frame for Transmit and the X.86
headers are checked for in the received data. If X.86 functionality is selected, the X.86 receiver byte boundary is
provided by the RBSYNC signal and the DS33R11 provides the transmit byte synchronization TBSYNC. No HDLC
encapsulation is performed.
Register Name:
LI.TRX86A
Register Description:
Register Address:
Transmit Receive X.86 Address
0D9h
Bit #
7
6
5
4
3
2
1
0
Name
Default
X86TRA7 X86TRA6 X86TRA5 X86TRA4 X86TRA3 X86TRA2 X86TRA1 X86TRA0
0
0
0
0
0
1
0
0
Bits 0 - 7: X86 Transmit Receive Address (X86TRA0-7) This is the address field for the X.86 transmitter and for
the receiver. The register default value is 0x04.
Register Name:
LI.TRX8C
Register Description:
Register Address:
Transmit Receive X.86 Control
0DAh
Bit #
7
6
5
4
3
2
1
0
Name
Default
X86TRC7 X86TRC6 X86TRC5 X86TRC4 X86TRC3 X86TRC2 X86TRC1 X86TRC0
0
0
0
0
0
0
1
1
Bits 0 - 7: X86 Transmit Receive Control (X86TRC0-7) This is the control field for the X.86 transmitter and
expected value for the receiver. The register is reset to 0x03
Register Name:
Register Description:
Register Address:
LI.TRX86SAPIH
Transmit Receive X.86 SAPIH
0DBh
Bit #
7
6
5
4
3
2
1
0
TRSAPIH7
TRSAPIH6
TRSAPIH5
TRSAPIH4
TRSAPIH3
TRSAPIH2
TRSAPIH1
TRSAPIH0
Name
Default
1
1
1
1
1
1
1
0
Bits 0 - 7: X86 Transmit Receive Address (TRSAPIH0-7) This is the address field for the X.86 transmitter and
expected for the receiver. The register is reset to 0xfe.
159 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.TRX86SAPIL
Register Description:
Register Address:
Transmit Receive X.86 SAPIL
0DCh
Bit #
7
TRSAPIL7
0
6
TRSAPIL6
0
5
TRSAPIL5
0
4
TRSAPIL4
0
3
TRSAPIL3
0
2
TRSAPIL2
0
1
TRSAPIL1
0
0
TRSAPIL0
1
Name
Default
Bits 0 – 7: X86 Transmit Receive Control (TRSAPIL0-7) This is the address field for the X.86 transmitter and
expected value for the receiver. The register is reset to 0x01
Register Name:
LI.CIR
Register Description:
Register Address:
Committed Information Rate
0DDh
Bit #
Name
Default
7
CIRE
0
6
CIR6
0
5
CIR5
0
4
CIR4
0
3
CIR3
0
2
CIR2
0
1
CIR1
0
0
CIR0
1
Bit 7: Committed Information Rate Enable (CIRE) Set this bit to 1 to enable the Committed Information Rate
Controller feature.
Bits 0 – 6: Committed Information Rate (CIR0-6) These bits provide the value for the committed information rate.
The value is multiplied by 500kbit/s to get the CIR value. The user must ensure that the CIR value is less than or
equal to the maximum Serial Interface transmit rate. The valid range is from 1 to 104. Any values outside this range
will result in unpredictable behavior. Note that a value of 104 translates to a 52Mbit/s line rate. Hence if the CIR is
above the line rate, the rate is not restricted by the CIR. For instance - if using a T1 line and the CIR is
programmed with a value of 104, it has no effect in restricting the rate.
160 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.5.3 Receive Serial Interface
Serial Receive Registers are used to control the HDLC Receiver associated with each Serial Interface. Note that
throughout this document HDLC Processor is also referred to as “Packet Processor”. The receive packet
processor block has seventeen registers.
11.5.3.1 Receive Serial Register Bit Descriptions
Register Name:
LI.RSLCR
Register Description:
Register Address:
Receive Serial Interface Configuration Register
100h
Bit #
7
6
5
4
3
2
1
0
Name
Default
-
0
-
0
-
0
-
0
-
0
-
0
-
0
RDENPLT
0
Bit 0: Receive Data Enable Polarity (RDENPLT) Receive Data Enable Polarity. If set to 1, RDEN Low enables
reception of the bit.
Register Name:
LI.RPPCL
Register Description:
Register Address:
Receive Packet Processor Control Low Register
101h
Bit #
Name
Default
7
-
0
6
-
0
5
RFPD
0
4
RF16
0
3
RFED
0
2
RDD
0
1
RBRE
0
0
RCCE
0
Bit 5: Receive FCS Processing Disable (RFPD) – When equal to 0, FCS processing is performed and FCS is
appended to packets. When set to 1, FCS processing is disabled (the packets do not have an FCS appended). In
X.86 mode, FCS processing is always enabled.
Bit 4: Receive FCS-16 Enable (RF16) – When 0, the error checking circuit uses a 32-bit FCS. When 1, the error
checking circuit uses a 16-bit FCS. This bit is ignored when FCS processing is disabled. In X.86 mode, the FCS is
always 32 bits.
Bit 3: Receive FCS Extraction Disable (RFED) – When 0, the FCS bytes are discarded. When 1, the FCS bytes
are passed on. This bit is ignored when FCS processing is disabled. In X.86 mode, FCS bytes are discarded.
Bit 2: Receive Descrambling Disable (RDD) – When equal to 0, X43+1 descrambling is performed. When set to
1, descrambling is disabled.
Bit 1: Receive Bit Reordering Enable (RBRE) – When equal to 0, reordering is disabled and the first bit received
is expected to be the MSB DT [7] of the byte. When set to 1, bit reordering is enabled and the first bit received is
expected to be the LSB DT [0] of the byte.
Bit 0: Receive Clear Channel Enable (RCCE) – When equal to 0, packet processing is enabled. When set to 1,
the device is in clear channel mode and all packet-processing functions except descrambling and bit reordering are
disabled.
161 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RMPSCL
Register Description:
Register Address:
Receive Maximum Packet Size Control Low Register
102h
Bit #
Name
Default
7
RMX7
1
6
RMX6
1
5
RMX5
1
4
RMX4
0
3
RMX3
0
2
RMX2
0
1
RMX1
0
0
RMX0
0
Bits 0 - 7: Receive Maximum Packet Size (RMX[7:0]) Eight bits of a sixteen bit value. Register description below.
Register Name:
LI.RMPSCH
Register Description:
Register Address:
Receive Maximum Packet Size Control High Register
103h
Bit #
Name
Default
7
RMX15
0
6
RMX14
0
5
RMX13
0
4
RMX12
0
3
RMX11
0
2
RMX10
1
1
RMX9
1
0
RMX8
1
Bits 0-7: Receive Maximum Packet Size (RMX[8:15]) These sixteen bits indicate the maximum allowable packet
size in bytes. The size includes the FCS bytes, but excludes bit/byte stuffing. Note: If the maximum packet size is
less than the minimum packet size, all packets are discarded. When packet processing is disabled, these sixteen
bits indicate the "packet" size the incoming data is to be broken into.
The maximum packet size allowable is 2016 bytes plus the FCS bytes. Any values programmed that are greater
than 2016 + FCS will have the same effect as 2016+ FCS value.
In X.86 mode, the X.86 encapsulation bytes are included in maximum size control.
Register Name:
LI.RPPSR
Register Description:
Register Address:
Receive Packet Processor Status Register
104h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
REPC
0
1
RAPC
0
0
RSPC
0
Bit 2: Receive FCS Errored Packet Count (REPC) This read only bit indicates that the receive FCS errored
packet count is nonzero.
Bit 1: Receive Aborted Packet Count (RAPC) This read only bit indicates that the receive aborted packet count
is nonzero.
Bit 0: Receive Size Violation Packet Count (RSPC) This read only bit indicates that the receive size violation
packet count is nonzero.
162 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RPPSRL
Register Description:
Register Address:
Receive Packet Processor Status Register Latched
105h
Bit #
Name
Default
7
REPL
-
6
RAPL
-
5
RIPDL
-
4
3
2
1
0
RSPDL
-
RLPDL
-
REPCL
-
RAPCL
-
RSPCL
-
Bit 7: Receive FCS Errored Packet Latched (REPL) This bit is set when a packet with an errored FCS is
detected.
Bit 6: Receive Aborted Packet Latched (RAPL) This bit is set when a packet with an abort indication is detected.
Bit 5: Receive Invalid Packet Detected Latched (RIPDL) This bit is set when a packet with a noninteger number
of bytes is detected.
Bit 4: Receive Small Packet Detected Latched (RSPDL) This bit is set when a packet smaller than the minimum
packet size is detected.
Bit 3: Receive Large Packet Detected Latched (RLPDL) This bit is set when a packet larger than the maximum
packet size is detected.
Bit 2: Receive FCS Errored Packet Count Latched (REPCL) This bit is set when the REPC bit in the RPPSR
register transitions from zero to one.
Bit 1: Receive Aborted Packet Count Latched (RAPCL) This bit is set when the RAPC bit in the RPPSR register
transitions from zero to one.
Bit 0: Receive Size Violation Packet Count Latched (RSPCL) This bit is set when the RSPC bit in the RPPSR
register transitions from zero to one.
163 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RPPSRIE
Register Description:
Register Address:
Receive Packet Processor Status Register Interrupt Enable
106h
Bit #
Name
Default
7
REPIE
0
6
RAPIE
0
5
RIPDIE
0
4
RSPDIE
0
3
RLPDIE
0
2
REPCIE
0
1
RAPCIE
0
0
RSPCIE
0
Bit 7: Receive FCS Errored Packet Interrupt Enable (REPIE) This bit enables an interrupt if the REPL bit in the
LI.RPPSRL register is set.
0 = interrupt disabled
1 = interrupt enabled
Bit 6: Receive Aborted Packet Interrupt Enable (RAPIE) This bit enables an interrupt if the RAPL bit in the
LI.RPPSRL register is set.
0 = interrupt disabled
1 = interrupt enabled
Bit 5: Receive Invalid Packet Detected Interrupt Enable (RIPDIE) This bit enables an interrupt if the RIPDL bit in
0 = interrupt disabled
1 = interrupt enabled
Bit 4: Receive Small Packet Detected Interrupt Enable (RSPDIE) This bit enables an interrupt if the RSPDL bit
0 = interrupt disabled
1 = interrupt enabled
Bit 3: Receive Large Packet Detected Interrupt Enable (RLPDIE) This bit enables an interrupt if the RLPDL bit
0 = interrupt disabled
1 = interrupt enabled
Bit 2: Receive FCS Errored Packet Count Interrupt Enable (REPCIE) This bit enables an interrupt if the REPCL
0 = interrupt disabled
1 = interrupt enabled
Bit 1: Receive Aborted Packet Count Interrupt Enable (RAPCIE) This bit enables an interrupt if the RAPCL bit
0 = interrupt disabled
1 = interrupt enabled
Bit 0: Receive Size Violation Packet Count Interrupt Enable (RSPCIE) This bit enables an interrupt if the
0 = interrupt disabled
1 = interrupt enabled
164 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RPCB0
Register Description:
Register Address:
Receive Packet Count Byte 0 Register
108h
Bit #
Name
Default
7
RPC7
0
6
RPC6
0
5
RPC5
0
4
RPC4
0
3
RPC3
0
2
RPC2
0
1
RPC1
0
0
RPC0
0
Bits 0 - 7: Receive Packet Count (RPC [7:0]) Eight bits of a 24-bit value. Register description below.
Register Name:
LI.RPCB1
Register Description:
Register Address:
Receive Packet Count Byte 1 Register
109h
Bit #
Name
Default
7
RPC15
0
6
RPC14
0
5
RPC13
0
4
RPC12
0
3
RPC11
0
2
RPC10
0
1
RPC09
0
0
RPC08
0
Bits 0 - 7: Receive Packet Count (RPC [15:8]) Eight bits of a 24-bit value. Register description below.
Register Name:
LI.RPCB2
Register Description:
Register Address:
Receive Packet Count Byte 2 Register
10Ah
Bit #
Name
Default
7
RPC23
0
6
RPC22
0
5
RPC21
0
4
RPC20
0
3
RPC19
0
2
RPC18
0
1
RPC17
0
0
RPC16
0
Bits 0 – 7: Receive Packet Count (RPC [23:16]) These twenty-four bits indicate the number of packets stored in
the receive FIFO without an abort indication. Note: Packets discarded due to system loopback or an overflow
condition are included in this count. This register is valid when clear channel is enabled.
165 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RFPCB0
Register Description:
Register Address:
Receive FCS Errored Packet Count Byte 0 Register
10Ch
Bit #
Name
Default
7
RFPC7
0
6
RFPC6
0
5
RFPC5
0
4
RFPC4
0
3
RFPC3
0
2
RFPC2
0
1
RFPC1
0
0
RFPC0
0
Bits 0 – 7: Receive FCS Errored Packet Count (RFPC[7:0]) Eight bits of a 24-bit value. Register description
below.
Register Name:
LI.RFPCB1
Register Description:
Register Address:
Receive FCS Errored Packet Count Byte 1 Register
10Dh
Bit #
Name
Default
7
RFPC15
0
6
RFPC14
0
5
RFPC13
0
4
RFPC12
0
3
RFPC11
0
2
RFPC10
0
1
RFPC9
0
0
RFPC8
0
Bits 0 – 7: Receive FCS Errored Packet Count (RFPC[15:8]) Eight bits of a 24-bit value. Register description
below.
Register Name:
LI.RFPCB2
Register Description:
Register Address:
Receive FCS Errored Packet Count Byte 2 Register
10Eh
Bit #
Name
Default
7
RFPC23
0
6
RFPC22
0
5
RFPC21
0
4
RFPC20
0
3
RFPC19
0
2
RFPC18
0
1
RFPC17
0
0
RFPC16
0
Receive FCS Errored Packet Count (RFPC[23:16]) These twenty-four bits indicate the number of packets
received with an FCS error. The byte count for these packets is included in the receive aborted byte count register
REBCR.
166 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RAPCB0
Register Description:
Register Address:
Receive Aborted Packet Count Byte 0 Register
110h
Bit #
Name
Default
7
RAPC7
0
6
RAPC6
0
5
RAPC5
0
4
RAPC4
0
3
RAPC3
0
2
RAPC2
0
1
RAPC1
0
0
RAPC0
0
Bits 0 - 7: Receive Aborted Packet Count (RAPC [7:0]) Eight bits of a 24-bit value. Register description below.
Register Name:
LI.RAPCB1
Register Description:
Register Address:
Receive Aborted Packet Count Byte 1 Register
111h
Bit #
Name
Default
7
RAPC15
0
6
RAPC14
0
5
RAPC13
0
4
RAPC12
0
3
RAPC11
0
2
RAPC10
0
1
RAPC9
0
0
RAPC8
0
Bits 0 - 7: Receive Aborted Packet Count (RAPC[15:8]) Eight bits of a 24-bit value. Register description below.
Register Name:
LI.RAPCB2
Register Description:
Register Address:
Receive Aborted Packet Count Byte 2 Register
112h
Bit #
Name
Default
7
RAPC23
0
6
RAPC22
0
5
RAPC21
0
4
RAPC20
0
3
RAPC19
0
2
RAPC18
0
1
RAPC17
0
0
RAPC16
0
Bits 0 – 7: Receive Aborted Packet Count (RAPC [23:16]) The twenty-four bit value from these three registers
indicates the number of packets received with a packet abort indication. The byte count for these packets is
included in the receive aborted byte count register REBCR.
167 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RSPCB0
Register Description:
Register Address:
Receive Size Violation Packet Count Byte 0 Register
114h
Bit #
Name
Default
7
RSPC7
0
6
RSPC6
0
5
RSPC5
0
4
RSPC4
0
3
RSPC3
0
2
RSPC2
0
1
RSPC1
0
0
RSPC0
0
Bits 0 - 7: Receive Size Violation Packet Count (RSPC [7:0]) Eight bits of a 24-bit value. Register description
below.
Register Name:
LI.RSPCB1
Register Description:
Register Address:
Receive Size Violation Packet Count Byte 1 Register
115h
Bit #
Name
Default
7
RSPC15
0
6
RSPC14
0
5
RSPC13
0
4
RSPC12
0
3
RSPC11
0
2
RSPC10
0
1
RSPC9
0
0
RSPC8
0
Bits 0 - 7: Receive Size Violation Packet Count (RSPC [15:8]) Eight bits of a 24-bit value. Register description
below.
Register Name:
LI.RSPCB2
Register Description:
Register Address:
Receive Size Violation Packet Count Byte 2 Registers
116h
Bit #
Name
Default
7
RSPC23
0
6
RSPC22
0
5
RSPC21
0
4
RSPC20
0
3
RSPC19
0
2
RSPC18
0
1
RSPC17
0
0
RSPC16
0
Bits 0 – 7: Receive Size Violation Packet Count (RSPC [23:16]) These twenty-four bits indicate the number of
packets received with a packet size violation (below minimum, above maximum, or noninteger number of bytes).
The byte count for these packets is included in the receive aborted byte count register REBCR.
168 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RBC0
Register Description:
Register Address:
Receive Byte Count 0 Register
118h
Bit #
Name
Default
7
RBC7
0
6
RBC6
0
5
RBC5
0
4
RBC4
0
3
RBC3
0
2
RBC2
0
1
RBC1
0
0
RBC0
0
Bits 0 - 7: Receive Byte Count (RBC [7:0]) Eight bits of a 32-bit value. Register description below.
Register Name:
LI.RBC1
Register Description:
Register Address:
Receive Byte Count 1 Register
119h
Bit #
Name
Default
7
RBC15
0
6
RBC14
0
5
RBC13
0
4
RBC12
0
3
RBC11
0
2
RBC10
0
1
RBC9
0
0
RBC8
0
Bits 0 - 7: Receive Byte Count (RBC [15:8]) Eight bits of a 32-bit value. Register description below.
Register Name:
LI.RBC2
Register Description:
Register Address:
Receive Byte Count 2 Register
11Ah
Bit #
Name
Default
7
RBC23
0
6
RBC22
0
5
RBC21
0
4
RBC20
0
3
RBC19
0
2
RBC18
0
1
RBC17
0
0
RBC16
0
Bits 0 - 7: Receive Byte Count (RBC [23:16]) Eight bits of a 32-bit value. Register description below.
Register Name:
LI.RBC3
Register Description:
Register Address:
Receive Byte Count 3 Register
11Bh
Bit #
Name
Default
7
RBC31
0
6
RBC30
0
5
RBC29
0
4
RBC28
0
3
RBC27
0
2
RBC26
0
1
RBC25
0
0
RBC24
0
Bits 0 – 7: Receive Byte Count (RBC [31:24]) These thirty-two bits indicate the number of bytes contained in
packets stored in the receive FIFO without an abort indication. Note: Bytes discarded due to FCS extraction,
system loopback, FIFO reset, or an overflow condition may be included in this count.
169 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RAC0
Register Description:
Register Address:
Receive Aborted Byte Count 0 Register
11Ch
Bit #
Name
Default
7
REBC7
0
6
REBC6
0
5
REBC5
0
4
REBC4
0
3
REBC3
0
2
REBC2
0
1
REBC1
0
0
REBC0
0
Bits 0 - 7: Receive Aborted Byte Count (RBC [7:0]) Eight bits of a 32-bit value. Register description below.
Register Name:
LI.RAC1
Register Description:
Register Address:
Receive Aborted Byte Count 1 Register
11Dh
Bit #
Name
Default
7
REBC15
0
6
REBC14
0
5
REBC13
0
4
REBC12
0
3
REBC11
0
2
REBC10
0
1
REBC9
0
0
REBC8
0
Bits 0 - 7: Receive Aborted Byte Count (RBC [15:8]) Eight bits of a 32-bit value. Register description below.
Register Name:
LI.RAC2
Register Description:
Register Address:
Receive Aborted Byte Count 2 Register
11Eh
Bit #
Name
Default
7
REBC23
0
6
REBC22
0
5
REBC21
0
4
REBC20
0
3
REBC19
0
2
REBC18
0
1
REBC17
0
0
REBC16
0
Bits 0 - 7: Receive Aborted Byte Count (RBC [16:23]) Eight bits of a 32-bit value. Register description below.
Register Name:
LI.RAC3
Register Description:
Register Address:
Receive Aborted Byte Count 3 Register
11Fh
Bit #
Name
Default
7
REBC31
0
6
REBC30
0
5
REBC29
0
4
REBC28
0
3
REBC27
0
2
REBC26
0
1
REBC25
0
0
REBC24
0
Bits 0 – 7: Receive Aborted Byte Count (REBC[31:24]) These thirty-two bits indicate the number of bytes
contained in packets stored in the receive FIFO with an abort indication. Note: Bytes discarded due to FCS
extraction, system loopback, FIFO reset, or an overflow condition may be included in this count.
170 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RHPMUU
Register Description:
Register Address:
Serial Interface Receive HDLC PMU Update Register
120h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
RPMUU
0
Bit 0: Receive PMU Update (RPMUU) This signal causes the receive cell/packet processor block performance
monitoring registers (counters) to be updated. A 0 to 1 transition causes the performance monitoring registers to be
updated with the latest data, and the counters reset (0 or 1). This update updates performance monitoring counters
for the Serial Interface.
Register Name:
LI.RHPMUS
Register Description:
Register Address:
Serial Interface Receive HDLC PMU Update Status Register
121h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
RPMUUS
0
Bit 0: Receive PMU Update Status (RPMUUS) This bit is set when the Transmit PMU Update is completed. This
bit is cleared when RPMUU is set to 0.
Register Name:
LI.RX86S
Register Description:
Register Address:
Receive X.86 Latched Status Register
122h
Bit #
Name
Default
7
-
-
6
-
-
5
-
-
4
-
-
3
2
1
CNE
-
0
ANE
-
SAPIHNE SAPILNE
-
-
Bit 3: SAPI High is not equal to LI.TRX86SAPIH Latched Status (SAPIHNE) This latched status bit is set if
SAPIH is not equal to LI.TRX86SAPIH. This latched status bit is cleared upon read.
Bit 2: SAPI Low is not equal to LI.TRX86SAPIL Latched Status (SAPILNE) This latched status bit is set if
Bit 1: Control is not equal to LI.TRX8C (CNE) This latched status bit is set if the control field is not equal to
LI.TRX8C. This latched status bit is cleared upon read.
Bit 0: Address is not equal to LI.TRX86A (ANE) This latched status bit is set if the X.86 Address field is not
171 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.RX86LSIE
Register Description:
Register Address:
Receive X.86 Interrupt Enable
123h
Bit #
Name
7
-
6
-
5
-
4
-
3
2
1
0
SAPINE01IM
SAPINEFEIM
CNE3LI
ANE4IM
M
Default
0
0
0
0
0
0
0
0
LI.RX86S.SAPIHNE will generate an interrupt.
LI.RX86S.SAPILNE will generate an interrupt.
Bit 1: Control not equal to LI.TRX8C Interrupt Enable (CNE3LIM) If this bit is set to 1, LI.RX86S.CNE will
generate an interrupt.
Bit 0: Address not equal to LI.TRX86A Interrupt Enable (ANE4IM) If this bit is set to 1, LI.RX86S.ANE will
generate an interrupt.
Register Name:
LI.TQLT
Register Description:
Register Address:
Serial Interface Transmit Queue Low Threshold (Watermark)
124h
Bit #
Name
Default
7
TQLT7
0
6
TQLT6
0
5
TQLT5
0
4
TQLT4
0
3
TQLT3
0
2
TQLT2
0
1
TQLT1
0
0
TQLT0
0
Bits 0 - 7: Transmit Queue Low Threshold (TQLT[0:7]) The transmit queue low threshold for the connection, in
increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to
determine the byte location of the threshold. Note that the transmit queue is for data that was received from the
Serial Interface to be sent to the Ethernet Interface.
Register Name:
LI.TQHT
Register Description:
Register Address:
Serial Interface Transmit Queue High Threshold (Watermark)
125h
Bit #
Name
Default
7
TQHT7
0
6
TQHT6
0
5
TQHT5
0
4
TQHT4
0
3
TQHT3
0
2
TQHT2
0
1
TQHT1
0
0
TQHT0
0
Bits 0 – 7: Transmit Queue High Threshold (TQHT[0:7]) The transmit queue high threshold for the connection,
in increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to
determine the byte location of the threshold. Note that the transmit queue is for data that was received from the
Serial Interface to be sent to the Ethernet Interface.
172 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
LI.TQTIE
Register Description:
Register Address:
Serial Interface Transmit Queue Cross Threshold Interrupt Enable
126h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
2
1
TQHTIE
0
0
TQLTIE
0
TFOVFIE TQOVFIE
0
0
Bit 3: Transmit FIFO Overflow for Connection Interrupt Enable (TFOVFIE) If this bit is set, the watermark
interrupt is enabled for TFOVFLS.
Bit 2: Transmit Queue Overflow for Connection Interrupt Enable (TQOVFIE) If this bit is set, the watermark
interrupt is enabled for TQOVFLS.
Bit 1: Transmit Queue for Connection High Threshold Interrupt Enable (TQHTIE) If this bit is set, the
watermark interrupt is enabled for TQHTS.
Bit 0: Transmit Queue for Connection Low Threshold Interrupt Enable (TQLTIE) If this bit is set, the
watermark interrupt is enabled for TQLTS.
Register Name:
LI.TQCTLS
Register Description:
Register Address:
Serial Interface Transmit Queue Cross Threshold Latched Status
127h
Bit #
Name
Default
7
-
-
6
-
-
5
-
-
4
-
-
3
2
1
0
TFOVFLS TQOVFLS TQHTLS
TQLTLS
-
-
-
-
Bit 3: Transmit Queue FIFO Overflowed Latched Status (TFOVFLS) This bit is set if the transmit queue FIFO
has overflowed. This register is cleared after a read. This FIFO is for data to be transmitted from the HDLC to be
sent to the SDRAM.
Bit 2: Transmit Queue Overflow Latched Status (TQOVFLS) This bit is set if the transmit queue has overflowed.
This register is cleared after a read.
Bit 1: Transmit Queue for Connection Exceeded High Threshold Latched Status (TQHTLS) This bit is set if
the transmit queue crosses the High Watermark. This register is cleared after a read.
Bit 0: Transmit Queue for Connection Exceeded Low Threshold Latched Status (TQLTLS) This bit is set if
the transmit queue crosses the Low Watermark. This register is cleared after a read.
173 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.6 Ethernet Interface Registers
The Ethernet Interface registers are used to configure RMII/MII bus operation and establish the MAC parameters
as required by the user. The MAC Registers cannot be addressed directly from the Processor port. The registers
below are used to perform indirect read or write operations to the MAC registers. The MAC Status Registers are
11.6.1 Ethernet Interface Register Bit Descriptions
Register Name:
SU.MACRADL
Register Description:
Register Address:
MAC Read Address Low Register
140h
Bit #
Name
Default
7
MACRA7
0
6
MACRA6
0
5
MACRA5
0
4
MACRA4
0
3
MACRA3
0
2
MACRA2
0
1
MACRA1
0
0
MACRA0
0
Bits 0 – 7: MAC Read Address (MACRA0-7) Low byte of the MAC indirect register address. Used only for read
operations.
Register Name:
SU.MACRADH
Register Description:
Register Address:
MAC Read Address High Register
141h
Bit #
7
6
5
4
3
2
1
0
Name
MACRA1
MACRA1
MACRA1
MACRA1
MACRA1
MACRA1
MACRA9
MACRA8
5
4
3
2
1
0
Default
0
0
0
0
0
0
0
0
Bits 0 – 7: MAC Read Address (MACRA8-15) High byte of the MAC indirect register address. Used only for read
operations.
Register Name:
Register Description:
Register Address:
SU.MACRD0
MAC Read Data Byte 0
142h
Bit #
Name
Default
7
MACRD7
0
6
MACRD6
0
5
MACRD5
0
4
MACRD4
0
3
MACRD3
0
2
MACRD2
0
1
MACRD1
0
0
MACRD0
0
Bits 0 – 7: MAC Read Data 0 (MACRD0-7) One of four bytes of data read from the MAC. Valid after a read
174 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.MACRD1
Register Description:
Register Address:
MAC Read Data Byte 1
143h
Bit #
Name
Default
7
6
5
4
3
2
1
0
MACRD15
MACRD14
MACRD13
MACRD12
MACRD11
MACRD10
MACRD9
MACRD8
0
0
0
0
0
0
0
0
Bits 0 - 7: MAC Read Data 1 (MACRD8-15) One of four bytes of data read from the MAC. Valid after a read
Register Name:
Register Description:
Register Address:
SU.MACRD2
MAC Read Data Byte 2
144h
Bit #
Name
7
6
5
4
3
2
1
0
MACRD23
MACRD22
MACRD21
MACRD20
MACRD19
MACRD18
MACRD17
MACRD16
Default
0
0
0
0
0
0
0
0
Bits 0 – 7: MAC Read Data 2 (MACRD16-23) One of four bytes of data read from the MAC. Valid after a read
Register Name:
Register Description:
Register Address:
SU.MACRD3
MAC Read Data byte 3
145h
Bit #
Name
Default
7
6
5
4
3
2
1
0
MACRD31
MACRD30
MACRD29
MACRD28
MACRD27
MACRD26
MACRD25
MACRD24
0
0
0
0
0
0
0
0
Bits 0 – 7: MAC Read Data 3 (MACRD24-31) One of four bytes of data read from the MAC. Valid after a read
Register Name:
Register Description:
Register Address:
SU.MACWD0
MAC Write Data 0
146h
Bit #
Name
Default
7
MACWD7
0
6
MACWD6
0
5
4
3
MACWD3
0
2
MACWD2
0
1
MACWD1
0
0
MACWD0
0
MACWD5
MACWD4
0
0
Bits 0 – 7: MAC Write Data 0 (MACWD0-7) One of four bytes of data to be written to the MAC. Data has been
175 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.MACWD1
Register Description:
Register Address:
MAC Write Data 1
147h
Bit #
Name
Default
7
6
5
4
3
2
1
0
MACWD15 MACWD14 MACWD13 MACWD12 MACWD11 MACWD10 MACWD09 MACWD08
0
0
0
0
0
0
0
0
Bits 0 – 7: MAC Write Data 1 (MACWD8-15) One of four bytes of data to be written to the MAC. Data has been
Register Name:
SU.MACWD2
Register Description:
Register Address:
MAC Write Data Register 2
148h
Bit #
Name
Default
7
6
5
4
3
2
1
0
MACWD23 MACWD22 MACWD21 MACWD20 MACWD19 MACWD18 MACWD17
MACWD16
0
0
0
0
0
0
0
0
Bits 0 - 7: MAC Write Data 2 (MACWD16-23) One of four bytes of data to be written to the MAC. Data has been
Register Name:
Register Description:
Register Address:
SU.MACWD3
MAC Write Data 3
149h
Bit #
Name
Default
7
6
5
4
3
2
1
0
MACD31
MACD30
MACD29
MACD28
MACD27
MACD26
MACD25
MACD24
0
0
0
0
0
0
0
0
Bits 0 – 7: MAC Write Data 3 (MACD24-31) One of four bytes of data to be written to the MAC. Data has been
Register Name:
Register Description:
Register Address:
SU.MACAWL
MAC Address Write Low
14Ah
Bit #
Name
Default
7
6
5
4
3
2
1
0
MACAW 7
MACAW 6
MACAW 5
MACAW4
MACAW3
MACAW2
MACAW1
MACAW0
0
0
0
0
0
0
0
0
Bits 0 -7: MAC Write Address (MACAW0-7) Low byte of the MAC indirect write address. Used only for write
operations.
176 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.MACAWH
Register Description:
Register Address:
MAC Address Write High
14Bh
Bit #
Name
Default
7
6
5
4
3
2
1
0
MACAW15
MACAW14
MACAW13
MACAW12 MACAW11 MACAW10
MACAW9
MACAW8
0
0
0
0
0
0
0
0
Bits 0 – 7: MAC Write Address (MACAW8-15) High byte of the MAC indirect write address. Used only for write
operations.
Register Name:
SU.MACRWC
Register Description:
Register Address:
MAC Read Write Command Status
14Ch
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
MCRW
0
0
MCS
0
Bit 1: MAC Command RW (MCRW) If this bit is written to 1, a read is performed from the MAC. If this bit is written
to 0, a write operation is performed. Address information for write operations must be located in SU.MACAWH and
SU.MACAWL. Address information for read operations must be located in SU.MACRADH and SU.MACRADL. The
user must also write a 1 to the MCS bit, and the DS33R11 will clear MCS when the operation is complete.
Bit 0: MAC Command Status (MCS) Setting MCS in conjunction with MCRW will initiate a read or write to the
MAC registers. Upon completion of the read or write this bit is cleared. Once a read or write command has been
initiated the host must poll this bit to see when the operation is complete.
177 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.LPBK
Register Description:
Register Address:
Ethernet Interface Loopback Control Register
14Fh
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
-
0
1
-
0
0
QLP
0
Bit 0: Queue Loopback Enable (QLP) If this bit is set to 1, data from the Ethernet Interface receive queue is
looped back to the transmit queue. Buffered data from the serial interface will remain until the loopback is removed.
Register Name:
SU.GCR
Register Description:
Register Address:
Ethernet Interface General Control Register
150h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
CRCS
0
2
H10S
0
1
ATFLOW
1
0
JAME
0
Bit 3: CRCS If this bit is zero (default), the received MAC or Ethernet Frame CRC is stripped before the data is
encapsulated and transmitted on the serial interface. Data received from the serial interface is decapsulated, a
CRC is recalculated and appended to the packet for transmission to the Ethernet interface. If this bit is set to 1, the
CRC is not stripped from received packets prior to encapsulation and transmission to the serial interface, and data
received from the serial interface is decapsulated directly. No CRC recalculation is performed on data received
from the serial interface. Note that the maximum packet size supported by the Ethernet interface is still 2016 (this
includes the 4 bytes of CRC).
Bit 2: H10S This bit controls the 10/100 selection for RMII and DCE Mode. When in RMII mode, setting this bit to
1 will cause the MAC will operate at 100 Mbps and setting this bit to zero will cause the MAC to operate at 10
Mbps. When in DCE mode, the bit function is inverted – setting this bit to 1 will cause the MAC to operate at 10
Mbps. In DTE and MII mode, the MAC determines the data rate from the incoming TX_CLK and RX_CLK.
Bit 1: Automatic Flow Control Enable (ATFLOW) If this bit is set to 1, automatic flow control is enabled based on
the connection receive queue size and high watermarks. Pause frames are sent automatically in full duplex mode.
The pause time must be programmed through SU.MACFCR. The jam sequence will not be sent automatically in
half duplex mode unless the JAME bit is set. This bit is applicable only in software mode.
Bit 0: Jam Enable (JAME) If this bit is set to 1, a Jam sequence is sent for a duration of 4 bytes. This function is
only valid in half duplex mode, and will only function if Automatic Flow Control is disabled. Note that if the receive
queue size is less than receive high threshold, setting a JAME will JAM one received frame. If JAME is set and the
receiver queue size is higher than the high threshold, all received frames are jammed until the queue empties
below the threshold.
178 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.TFRC
Register Description:
Register Address:
Transmit Frame Resend Control
151h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
NCFQ
0
2
TPDFCB
0
1
TPRHBC
0
0
TPRCB
0
Bit 3: No Carrier Queue Flush Bar (NCFQ) If this bit is set to 1, the queue for data passing from Serial Interface
to Ethernet Interface will not be flushed when loss of carrier is detected.
Bit 2: Transmit Packet Deferred Fail Control Enable (TPDFCB) If this bit if set to 1, the current frame is
transmitted immediately instead of being deferred. If this bit is set to 0, the frame is deferred if CRS is asserted and
sent when the CRS is unasserted indicating the media is idle.
Bit 1: Transmit Packet HB Fail Control Bar (TPRHBC) If this bit is set to 1, the current frame will not be
retransmitted if a heartbeat failure is detected.
Bit 0: Transmit Packet Resend Control Bar (TPRCB) If this bit is set to 1, the current frame will not be
retransmitted if any of the following errors have occurred:
•
•
•
•
•
•
•
Jabber time out
Loss of carrier
Excessive deferral
Late collision
Excessive collisions
Under run
Collision
Note that blocking retransmission due to collision (applicable in MIII/Half Duplex Mode) can result in unpredictable
system level behavior.
179 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.TFSL
Register Description:
Register Address:
Transmit Frame Status Low
152h
Bit #
Name
Default
7
UR
0
6
EC
0
5
LC
0
4
ED
0
3
LOC
0
2
NOC
0
1
-
0
0
FABORT
0
Bit 7: Under Run (UR) When this bit is set to 1, the frame was aborted due to a data under run condition of the
transmit buffer.
Bit 6: Excessive Collisions (EC) When this bit is set to 1, a frame has been aborted after 16 successive collisions
while attempting to transmit the current frame. If the Disable Retry bit is set to 1, then Excessive Collisions will be
set to 1 after the first collision.
Bit 5: Late Collision (LC) When this bit is set to 1, a frame was aborted by collision after the 64 bit collision
window. Not valid if an under run has occurred.
Bit 4: Excessive Deferral (ED) When this bit is set to 1, a frame was aborted due to excessive deferral.
Bit 3: Loss Of Carrier (LOC) When this bit is set to 1, a frame was aborted due to loss of carrier for one or more
bit times. Valid only for noncollided frames. Valid only in half-duplex operation.
Bit 2: No Carrier (NOC) When this bit is set to 1, a frame was aborted because no carrier was found for
transmission.
Bit 1: Reserved
Bit 0: Frame Abort (FABORT) When this bit is set to 1, the MAC has aborted a frame for one of the above
reasons. When this bit is clear, the previous frame has been transmitted successfully.
Register Name:
SU.TFSH
Register Description:
Register Address:
Transmit Frame Status High
153h
Bit #
Name
Default
7
PR
0
6
HBF
0
5
CC3
0
4
CC2
0
3
CC1
0
2
CC0
0
1
LCO
0
0
DEF
0
Bit 7: Packet Resend (PR) When this bit is set, the current packet must be retransmitted due to a collision.
Bit 6: Heartbeat Failure (HBF) When this bit is set, the device failed to detect a heart beat after transmission. This
bit is not valid if an under run has occurred.
Bits 2-5: Collision Count (CC0-3) These 4 bits indicate the number of collisions that occurred prior to successful
transmission of the previous frame. Not valid if Excessive Collisions is set to 1.
Bit 1: Late Collision (LCO) When set to 1, the MAC observed a collision after the 64-byte collision window.
Bit 0: Deferred Frame (DEF) When set to 1, the current frame was deferred due to carrier assertion by another
node after being ready to transmit.
180 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.RFSB0
Register Description:
Register Address:
Receive Frame Status Byte 0
154h
Bit #
Name
Default
7
FL7
0
6
FL6
0
5
FL5
0
4
FL4
0
3
FL3
0
2
FL2
0
1
FL1
0
0
FL0
0
Bits 0 - 7: Frame Length (FL[0:7]) These 8 bits are the low byte of the length (in bytes) of the received frame,
with FCS and Padding. If Automatic Pad Stripping is enabled, this value is the length of the received packet without
PCS or Pad bytes. The upper 6 bits are contained in SU.RFSB1.
Register Name:
SU.RFSB1
Register Description:
Register Address:
Receive Frame Status Byte 1
155h
Bit #
Name
Default
7
RF
0
6
WT
0
5
FL13
0
4
FL12
0
3
FL11
0
2
FL10
0
1
FL9
0
0
FL8
0
Bit 7: Runt Frame (RF) This bit is set to 1 if the received frame was altered by a collision or terminated within the
collision window.
Bit 6: Watchdog Timeout (WT) This bit is set to 1 if a packet receive time exceeds 2048 byte times. After 2048
byte times the receiver is disabled and the received frame will fail CRC check.
Bits 0-5: Frame Length (FL[8:13]) These 6 bits are the upper bits of the length (in bytes) of the received frame,
with FCS and Padding. If Automatic Pad Stripping is enabled, this value is the length of the received packet without
PCS or Pad bytes.
Register Name:
SU.RFSB2
Register Description:
Register Address:
Receive Frame Status Byte 2
156h
Bit #
Name
Default
7
-
0
6
-
0
5
CRCE
0
4
DB
0
3
MIIE
0
2
FT
0
1
CS
0
0
FTL
0
Bit 5: CRC Error (CRCE) This bit is set to 1 if the received frame does not contain a valid CRC value.
Bit 4: Dribbling Bit (DB) This bit is set to 1 if the received frame contains a noninteger multiple of 8 bits. It does
not indicate that the frame is invalid. This bit is not valid for runt or collided frames.
Bit 3: MII Error (MIIE) This bit is set to 1 if an error was found on the MII bus.
Bit 2: Frame Type (FT) This bit is set to 1 if the received frame exceeds 1536 bytes. It is equal to zero if the
received frame is an 802.3 frame. This bit is not valid for runt frames.
Bit 1: Collision Seen (CS) This bit is set to 1 if a late collision occurred on the received packet. A late collision is
one that occurs after the 64 byte collision window.
Bit 0: Frame Too Long (FTL) This bit is set to 1 if a frame exceeds the 1518 byte maximum standard Ethernet
frame. This bit is only an indication, and causes no frame truncation.
181 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.RFSB3
Register Description:
Register Address:
Receive Frame Status Byte 3
157h
Bit #
Name
Default
7
MF
0
6
-
0
5
-
0
4
BF
0
3
MCF
0
2
UF
0
1
CF
0
0
LE
0
Bit 7: Missed Frame (MF) This bit is set to 1 if the packet is not successfully received from the MAC by the packet
Arbiter.
Bit 4: Broadcast Frame (BF) This bit is set to 1 if the current frame is a broadcast frame.
Bit 3: Multicast Frame (MCF) This bit is set to 1 if the current frame is a multicast frame.
Bit 2: Unsupported Control Frame (UF) This bit is set to 1 if the frame received is a control frame with an opcode
that is not supported. If the Control Frame bit is set, and the Unsupported Control Frame bit is clear, then a pause
frame has been received and the transmitter is paused.
Bit 1: Control Frame (CF) This bit is set to 1 when the current frame is a control frame. This bit is only valid in full-
duplex mode.
Bit 0: Length Error (LE) This bit is set to 1 when the frames length field and the actual byte count are unequal.
This bit is only valid for 802.3 frames.
182 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.RMFSRL
Register Description:
Register Address:
Receiver Maximum Frame Low Register
158h
Bit #
Name
Default
7
RMPS7
1
6
RMPS6
1
5
RMPS5
1
4
RMPS4
0
3
RMPS3
0
2
RMPS2
0
1
RMPS1
0
0
RMPS0
0
Bits 7- 0: Receiver Maximum Frame (RMPS[0:7]) Eight bits of sixteen bit value. Register description below.
Register Name:
SU.RMFSRH
Register Description:
Register Address:
Receiver Maximum Frame High Register
159h
Bit #
Name
Default
7
RMPS15
0
6
RMPS14
0
5
RMPS13
0
4
RMPS12
0
3
RMPS11
0
2
RMPS10
1
1
RMPS9
1
0
RMPS8
1
Bits 7- 0: Receiver Maximum Frame (RMPS[8:15]) This value is the receiver’s maximum frame size (in bytes),
up to a maximum of 2016 bytes. Any frame received greater than this value is rejected. The frame size includes
destination address, source address, type/length, data and crc-32. The frame size is not the same as the frame
length encoded within the IEEE 802.3 frame. Any values programmed that are greater than 2016 will have
unpredictable behavior and should be avoided.
Register Name:
SU.RQLT
Register Description:
Register Address:
Receive Queue Low Threshold (Watermark)
15Ah
Bit #
Name
Default
7
RQLT7
0
6
RQLT6
0
5
RQLT5
0
4
RQLT4
0
3
RQLT3
0
2
RQLT2
0
1
RQLT1
0
0
RQLT0
0
Bits 0 - 7: Receive Queue Low Threshold (RQLT[0:7]) The receive queue low threshold for the connection, in
increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to
determine the byte location of the threshold. Note that the receive queue is for data that was received from the
Ethernet Interface to be sent to the Serial Interface.
Register Name:
SU.RQHT
Register Description:
Register Address:
Receive Queue High Threshold (Watermark)
15Bh
Bit #
Name
Default
7
RQHT7
0
6
RQHT6
0
5
RQHT5
0
4
RQHT4
0
3
RQHT3
0
2
RQHT2
0
1
RQHT1
0
0
RQHT0
0
Bits 0 – 7: Receive Queue High Threshold (RQTH[0:7]) The receive queue high threshold for the connection, in
increments of 32 packets of 2048 bytes each. The value of this register is multiplied by 32 * 2048 bytes to
determine the byte location of the threshold. Note that the receive queue is for data that was received from the
Ethernet Interface to be sent to the Serial Interface.
183 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.QRIE
Register Description:
Register Address:
Receive Queue Cross Threshold enable
15Ch
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
RFOVFIE
0
2
RQVFIE
0
1
RQLTIE
0
0
RQHTIE
0
Bit 3: Receive FIFO Overflow Interrupt Enable (RFOVFIE) If this bit is set, the interrupt is enabled for RFOVFLS.
Bit 2: Receive Queue Overflow Interrupt Enable (RQVFIE) If this bit is set, the interrupt is enabled for
RQOVFLS.
Bit 1: Receive Queue Crosses Low Threshold Interrupt Enable (RQLTIE) If this bit is set, the watermark
interrupt is enabled for RQLTS.
Bit 0: Receive Queue Crosses High Threshold Interrupt Enable (RQHTIE) If this bit is set, the watermark
interrupt is enabled for RQHTS.
Register Name:
SU.QCRLS
Register Description:
Register Address:
Queue Cross Threshold Latched Status
15Dh
Bit #
Name
Default
7
-
-
6
-
-
5
-
-
4
-
-
3
2
1
0
RFOVFLS
-
RQOVFLS
-
RQHTLS
-
RQLTLS
-
Bit 3: Receive FIFO Overflow latched Status (RFOVFLS) This bit is set if the receive FIFO overflows for the data
to be transmitted from the MAC to the SDRAM.
Bit 2: Receive Queue Overflow Latched Status (RQOVFLS) This bit is set if the receive queue has overflowed.
This register is cleared after a read.
Bit 1: Receive Queue for Connection Crossed High Threshold Latched Status (RQHTLS) This bit is set if the
receive queue crosses the high Watermark. This register is cleared after a read.
Bit 0: Receive Queue for Connection Crossed Low Threshold Latched Status (RQLTLS) This bit is set if the
receive queue crosses the low Watermark. This register is cleared after a read.
Note the bit order differences in the high/low threshold indications in SU.QCRLS and the interrupt enables in
SU.QRIE.
184 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.RFRC
Register Description:
Register Address:
Receive Frame Rejection Control
15Eh
Bit #
Name
Default
7
-
0
6
UCFR
0
5
CFRR
0
4
LERR
0
3
CRCERR
0
2
DBR
0
1
MIIER
0
0
BFR
0
Bit 6: Uncontrolled Control Frame Reject (UCFR) When set to 1, Control Frames other than Pause Frames are
allowed. When this bit is equal to zero, nonpause control frames are rejected.
Bit 5: Control Frame Reject (CFRR) When set to 1, control frames are allowed. When this bit is equal to zero, all
control frames are rejected.
Bit 4: Length Error Reject (LERR) When set to 1, frames with an unmatched frame length field and actual
number of bytes received are allowed. When equal to zero, only frames with matching length fields and actual
bytes received will be allowed.
Bit 3: CRC Error Reject (CRCERR) When set to 1, frames received with a CRC error or MII error are allowed.
When equal to zero, frames with CRC or MII errors are rejected.
Bit 2: Dribbling Bit Reject (DBR) When set to 1, frames with lengths of noninteger multiples of 8 bits are allowed.
When equal to zero, frames with dribbling bits are rejected. The dribbling bit setting is only valid only if there is not
a collision or runt frame.
Bit 1: MII Error Reject (MIIER) When set to 1, frames are allowed with MII Receive Errors. When equal to zero,
frames with MII errors are rejected.
Bit 0: Broadcast Frame Reject (BFR) When set to 1, broadcast frames are allowed. When equal to zero,
broadcast frames are rejected.
185 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.6.2 MAC Registers
The control Registers related to the control of the individual Mac’s are shown in the following Table. The DS33R11
keeps statistics for the packet traffic sent and received. The register address map is shown in the following Table.
Note that the addresses listed are the indirect addresses that must be provided to SU.MACRADH/SU.MACRADL
Register Name:
SU.MACCR
Register Description:
Register Address:
MAC Control Register
0000h (indirect)
0000h:
Bit #
Name
Default
31
Reserved
0
30
29
28
HDB
0
27
PS
0
26
Reserved
0
25
24
Reserved Reserved
Reserved Reserved
0
0
0
0
0001h:
Bit #
Name
Default
23
DRO
0
22
Reserved
0
21
OML0
0
20
F
0
19
PM
0
18
PAM
0
17
16
Reserved Reserved
0
0
0002h:
Bit #
Name
Default
15
Reserved
0
14
13
12
LCC
0
11
Reserved
0
10
DRTY
0
09
Reserved
0
08
ASTP
0
Reserved Reserved
0
0
0003h:
Bit #
Name
Default
07
BOLMT1
0
06
BOLMT0
0
05
DC
0
04
Reserved
0
03
TE
0
02
RE
0
01
00
Reserved Reserved
0
0
Bit 28: Heartbeat Disable (HDB) When set to 1, the heartbeat (SQE) function is disabled. This bit should be set to
1 when operating in MII mode.
Bit 27: Port Select (PS) This bit should be equal to 0 for proper operation.
Bit 23: Disable Receive Own (DRO) When set to 1, the MAC disables the reception of frames while TX_EN is
asserted. When this bit equals zero, transmitted frames are also received by the MAC. This bit should be cleared
when operating in full-duplex mode.
Bit 21: Loopback Operating Mode (OMLO) When set to 1, data is looped from the transmit side, back to the
receive side, without being transmitted to the PHY.
Bit 20: Full-Duplex Mode Select (F) When set to 1, the MAC transmits and receives data simultaneously. When
in full-duplex mode, the heartbeat check is disabled and the heartbeat fail status should be ignored.
Bit 19: Promiscuous Mode (PM) When set to 1, the MAC is in Promiscuous Mode and forwards all frames. Note
that the default value is 1.
Bit 18: Pass All Multicast (PAM) When set to 1, the MAC forwards Multicast Frames.
186 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Bit 12: Late Collision Control (LCC) When set to 1, enables retransmission of a collided packet even after the
collision period. When this bit is clear, retransmission of late collisions is disabled.
Bit 10: Disable Retry (DRTY) When set to 1, the MAC makes only a single attempt to transmit each frame. If a
collision occurs, the MAC ignores the current frame and proceeds to the next frame. When this bit equals 0, the
MAC will retry collided packets 16 times before signaling a retry error.
Bit 8: Automatic Pad Stripping (ASTP) When set to 1, all incoming frames with less than 46 byte length are
automatically stripped of the pad characters and FCS.
Bits 6 - 7: Back-Off Limit (BOLMT[0:1]) These two bits allow the user to set the back-off limit used for the
maximum retransmission delay for collided packets. Default operation limits the maximum delay for retransmission
to a countdown of 10 bits from a random number generator. The user can reduce the maximum number of counter
bits as described in the table below. See IEEE 802.3 for details of the back-off algorithm.
Bit 7
Bit 6
Random Number Generator Bits Used
0
0
1
1
0
1
0
1
10
8
4
1
Bit 5: Deferral Check (DC) When set to 1, the MAC will abort packet transmission if it has deferred for more than
24,288 bit times. The deferral counter starts when the transmitter is ready to transmit a packet, but is prevented
from transmission because CRS is active. If the MAC begins transmission but a collision occurs after the beginning
of transmission, the deferral counter is reset again. If this bit is equal to zero, then the MAC will defer indefinitely.
Bit 3: Transmitter Enable (TE) When set to 1, packet transmission is enabled. When equal to zero, transmission
is disabled.
Bit 2: Receiver Enable (RE) When set to 1, packet reception is enabled. When equal to zero, packets are not
received.
187 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.MACMIIA
Register Description:
Register Address:
MAC MII Management (MDIO) Address Register
0014h (indirect)
0014h:
Bit #
Name
Default
31
Reserved
0
30
29
28
27
26
25
24
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0015h:
Bit #
Name
Default
23
Reserved
0
22
21
20
19
18
17
16
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0016h:
Bit #
Name
Default
15
PHYA4
0
14
PHYA3
1
13
PHYA2
0
12
PHYA1
1
11
PHYA0
1
10
MIIA4
0
09
MIIA3
1
08
MIIA2
0
0017h:
Bit #
Name
Default
07
MIIA1
1
06
MIIA0
1
05
Reserved
0
04
03
02
01
MIIW
0
00
MIIB
0
Reserved Reserved Reserved
0
0
0
Bits 11 - 15: PHY Address (PHYA[0:4]) These 5 bits select one of the 32 available PHY address locations to
access through the PHY management (MDIO) bus.
Bits 6 - 10: MII Address (MIIA[0:4]) - These 5 bits are the address location within the PHY that is being accessed.
Bit 1: MII Write (MIIW) Write this bit to 1 in order to execute a write instruction over the MDIO interface. Write the
bit to zero to execute a read instruction.
Bit 0: MII Busy (MIIB) This bit is set to 1 by the DS33R11 during execution of a MII management instruction
through the MDIO interface, and is set to zero when the DS33R11 has completed the instruction. The user should
read this bit and ensure that it is equal to zero prior to beginning a MDIO instruction.
188 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.MACMIID
Register Description:
Register Address:
MAC MII (MDIO) Data Register
0018h (indirect)
0018h:
Bit #
Name
Default
31
Reserved
0
30
29
28
27
26
25
24
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0019h:
Bit #
Name
Default
23
Reserved
0
22
21
20
19
18
17
16
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
001Ah:
Bit #
Name
Default
15
MIID15
0
14
MIID14
0
13
MIID13
0
12
MIID12
0
11
MIID11
0
10
MIID10
0
09
MIID09
0
08
MIID08
0
001Bh:
Bit #
Name
Default
07
MIID07
0
06
MIID06
0
05
MIID05
0
04
MIID04
0
03
MIID03
0
02
MIID02
0
01
MIID01
0
00
MIID00
0
Bits 0 – 15: MII (MDIO) Data (MIID[00:15]) These two bytes contain the data to be written to or the data read from
the MII management interface (MDIO).
189 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.MACFCR
Register Description:
Register Address:
MAC Flow Control Register
001Ch (indirect)
001Ch:
Bit #
Name
Default
31
PT15
0
30
PT14
0
29
PT13
0
28
PT12
0
27
PT11
0
26
PT10
0
25
PT09
0
24
PT08
0
001Dh:
Bit #
Name
Default
23
PT07
0
22
PT06
1
21
PT05
0
20
PT04
1
19
PT03
0
18
PT02
0
17
PT01
0
16
PT00
0
001Eh:
Bit #
Name
Default
15
Reserved
0
14
13
12
11
10
09
08
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
001Fh:
Bit #
07
06
05
04
03
02
01
00
Name
Reserved
Reserve
Reserved
Reserved Reserved Reserved
FCE
FCB
d
Default
0
0
0
0
0
0
1
0
Bits 16 - 31: Pause Time (PT[00:15]) These bits are used for the Pause Time Field in transmitted Pause Frames.
This value is the number of time slots the remote node should wait prior to transmission.
Bit 1: Flow Control Enable (FCE) When set to 1, the MAC automatically detects pause frames and will disable
the transmitter for the requested pause time.
Bit 0: Flow Control Busy (FCB) The host can set this bit to 1 in order to initiate transmission of a pause frame.
During transmission of a pause frame, this bit remains set. The DS33R11 will clear this bit when transmission of
the pause frame has been completed. The user should read this bit and ensure that this bit is equal to zero prior to
initiating a pause frame.
190 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.MMCCTRL
Register Description:
Register Address:
MAC MMC Control Register
0100h (indirect)
0100h:
Bit #
Name
Default
31
Reserved
0
30
29
28
27
26
25
24
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0101h:
Bit #
Name
Default
23
Reserved
0
22
21
20
19
18
17
16
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0102h:
Bit #
Name
Default
15
Reserved
0
14
13
12
11
10
MXFRM7
1
09
MXFRM6
1
08
MXFRM5
1
Reserved MXFRM10 MXFRM9 MXFRM8
0
1
0
1
0103h:
Bit #
07
06
05
04
03
02
01
00
Name
Default
MXFRM4 MXFRM3 MXFRM2
MXFRM1 MXFRM0 Reserved
Reserved Reserved
0
1
1
1
0
0
1
0
Bits 3 - 13: Maximum Frame Size (MXFRM[0:10]) These bits indicate the maximum packet size value. All
transmitted frames larger than this value are counted as long frames.
Bit 1: Reserved - Note that this bit must be written to a “1” for proper operation.
191 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
Reserved
Register Description:
Register Address:
MAC Reserved Control Register
010Ch (indirect)
010Ch:
Bit #
Name
Default
31
Reserved
0
30
29
28
27
26
25
24
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
010Dh:
Bit #
Name
Default
23
Reserved
0
22
21
20
19
18
17
16
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
010Eh:
Bit #
Name
Default
15
Reserved
0
14
13
12
11
10
09
08
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
010Fh:
Bit #
07
06
05
04
03
02
01
00
Name
Reserved
Reserve
Reserved
Reserved Reserved Reserved
Reserved Reserved
d
Default
0
0
0
0
0
0
0
0
Note – Addresses 10Ch through 10Fh must each be initialized with all 1’s (FFh) for proper software-mode
operation.
192 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
Reserved
Register Description:
Register Address:
MAC Reserved Control Register
0110h (indirect)
0110h:
Bit #
Name
Default
31
Reserved
0
30
29
28
27
26
25
24
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0111h:
Bit #
Name
Default
23
Reserved
0
22
21
20
19
18
17
16
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0112h:
Bit #
Name
Default
15
Reserved
0
14
13
12
11
10
09
08
Reserved Reserved Reserved Reserved Reserved
Reserved Reserved
0
0
0
0
0
0
0
0113h:
Bit #
07
06
05
04
03
02
01
00
Name
Reserved
Reserve
Reserved
Reserved Reserved Reserved
Reserved Reserved
d
Default
0
0
0
0
0
0
0
0
Note – Addresses 110h through 113h must each be initialized with all 1’s (FFh) for proper software-mode
operation.
193 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.RxFrmCtr
Register Description:
Register Address:
MAC All Frames Received Counter
0200h (indirect)
0200h:
Bit #
Name
Default
31
RXFRMC31
0
30
RXFRMC30
0
29
RXFRMC29
0
28
RXFRMC28
0
27
RXFRMC27
0
26
RXFRMC26
0
25
RXFRMC25
0
24
RXFRMC24
0
0201h:
Bit #
Name
Default
23
RXFRMC23
0
22
RXFRMC22
0
21
RXFRMC21
0
20
RXFRMC20
0
19
RXFRMC19
0
18
RXFRMC18
0
17
RXFRMC17
0
16
RXFRMC16
0
0202h:
Bit #
Name
Default
15
RXFRMC15
0
14
RXFRMC14
0
13
RXFRMC13
0
12
RXFRMC12
0
11
RXFRMC11
0
10
RXFRMC10
0
09
RXFRMC9
0
08
RXFRMC8
0
0203h:
Bit #
Name
Default
07
RXFRMC7
0
06
RXFRMC6
0
05
RXFRMC5
0
04
RXFRMC4
0
03
RXFRMC3
0
02
RXFRMC2
0
01
RXFRMC1
0
00
RXFRMC0
0
Bits 0 - 31: All Frames Received Counter (RXFRMC[0:31]) 32 bit value indicating the number of frames
received. Each time a frame is received, this counter is incremented by 1. This counter resets only upon device
reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the
measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at
the maximum frame rate. The user should store the value from the beginning of the measurement period for later
calculations, and take into account the possibility of a roll-over to occurring.
194 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.RxFrmOkCtr
Register Description:
Register Address:
MAC Frames Received OK Counter
0204h (indirect)
0204h:
Bit #
31
30
29
28
27
26
25
24
RXFRMOK31 RXFRMOK30 RXFRMOK29 RXFRMOK28 RXFRMOK27 RXFRMOK26 RXFRMOK25 RXFRMOK24
Name
Default
0
0
0
0
0
0
0
0
0205h:
Bit #
23
22
21
20
19
18
17
16
RXFRMOK23 RXFRMOK22 RXFRMOK21 RXFRMOK20 RXFRMOK19 RXFRMOK18 RXFRMOK17 RXFRMOK16
Name
Default
0
0
0
0
0
0
0
0
0206h:
Bit #
Name
Default
15
14
13
12
11
10
09
08
RXFRMOK8
0
RXFRMOK15 RXFRMOK14 RXFRMOK13 RXFRMOK12 RXFRMOK11 RXFRMOK10 RXFRMOK9
0
0
0
0
0
0
0
0207h:
Bit #
Name
Default
07
RXFRMOK7
0
06
RXFRMOK6
0
05
RXFRMOK5
0
04
RXFRMOK4
0
03
RXFRMOK3
0
02
RXFRMOK2
0
01
RXFRMOK1
0
00
RXFRMOK0
0
Bits 0 - 31: Frames Received OK Counter (RXFRMOK[0:31]) 32 bit value indicating the number of frames
received and determined to be valid. Each time a valid frame is received, this counter is incremented by 1. This
counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value.
The user should ensure that the measurement period is less than the minimum length of time required for the
counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning
of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
195 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.TxFrmCtr
Register Description:
Register Address:
MAC All Frames Transmitted Counter
0300h (indirect)
0300h:
Bit #
Name
Default
31
TXFRMC31
0
30
TXFRMC30
0
29
TXFRMC29
0
28
TXFRMC28
0
27
TXFRMC27
0
26
TXFRMC26
0
25
TXFRMC25
0
24
TXFRMC24
0
0301h:
Bit #
Name
Default
23
TXFRMC23
0
22
TXFRMC22
0
21
TXFRMC21
0
20
TXFRMC20
0
19
TXFRMC19
0
18
TXFRMC18
0
17
TXFRMC17
0
16
TXFRMC16
0
0302h:
Bit #
Name
Default
15
TXFRMC15
0
14
TXFRMC14
0
13
TXFRMC13
0
12
TXFRMC12
0
11
TXFRMC11
0
10
TXFRMC10
0
09
TXFRMC9
0
08
TXFRMC8
0
0303h:
Bit #
Name
Default
07
TXFRMC7
0
06
TXFRMC6
0
05
TXFRMC5
0
04
TXFRMC4
0
03
TXFRMC3
0
02
TXFRMC2
0
01
TXFRMC1
0
00
TXFRMC0
0
Bits 0 - 31: All Frames Transmitted Counter (TXFRMC[0:31]) 32 bit value indicating the number of frames
transmitted. Each time a frame is transmitted, this counter is incremented by 1. This counter resets only upon
device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure
that the measurement period is less than the minimum length of time required for the counter to increment 2^32-1
times at the maximum frame rate. The user should store the value from the beginning of the measurement period
for later calculations, and take into account the possibility of a roll-over to occurring.
196 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.TxBytesCtr
Register Description:
Register Address:
MAC All Bytes Transmitted Counter
0308h (indirect)
0308h:
Bit #
Name
Default
31
TXBYTEC31
0
30
TXBYTEC30
0
29
TXBYTEC29
0
28
TXBYTEC28
0
27
TXBYTEC27
0
26
TXBYTEC26
0
25
TXBYTEC25
0
24
TXBYTEC24
0
0309h:
Bit #
Name
Default
23
TXBYTEC23
0
22
TXBYTEC22
0
21
TXBYTEC21
0
20
TXBYTEC20
0
19
TXBYTEC19
0
18
TXBYTEC18
0
17
TXBYTEC17
0
16
TXBYTEC16
0
030Ah:
Bit #
Name
Default
15
TXBYTEC15
0
14
TXBYTEC14
0
13
TXBYTEC13
0
12
TXBYTEC12
0
11
TXBYTEC11
0
10
TXBYTEC10
0
09
TXBYTEC9
0
08
TXBYTEC8
0
030Bh:
Bit #
07
06
05
04
03
02
01
00
TXBYTEC7 TXBYTEC6 TXBYTEC5 TXBYTEC4 TXBYTEC3 TXBYTEC2 TXBYTEC1 TXBYTEC0
Name
Default
0
0
0
0
0
0
0
0
Bits 0 - 31: All Bytes Transmitted Counter (TXBYTEC[0:31]) 32 bit value indicating the number of bytes
transmitted. Each time a byte is transmitted, this counter is incremented by 1. This counter resets only upon device
reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should ensure that the
measurement period is less than the minimum length of time required for the counter to increment 2^32-1 times at
the maximum data rate. The user should store the value from the beginning of the measurement period for later
calculations, and take into account the possibility of a roll-over to occurring.
197 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.TxBytesOkCtr
Register Description:
Register Address:
MAC Bytes Transmitted OK Counter
030Ch (indirect)
030Ch:
Bit #
31
30
29
28
27
26
25
24
TXBYTEOK31
TXBYTEOK30
TXBYTEOK29
TXBYTEOK28
TXBYTEOK27
TXBYTEOK26
TXBYTEOK25
TXBYTEOK24
Name
Default
0
0
0
0
0
0
0
0
030Dh:
Bit #
23
22
21
20
19
18
17
16
TXBYTEOK23
TXBYTEOK22
TXBYTEOK21
TXBYTEOK20
TXBYTEOK19
TXBYTEOK18
TXBYTEOK17
TXBYTEOK16
Name
Default
0
0
0
0
0
0
0
0
030Eh:
Bit #
15
14
13
12
11
10
09
08
TXBYTEOK15
TXBYTEOK14
TXBYTEOK13
TXBYTEOK12
TXBYTEOK11
TXBYTEOK10
TXBYTEOK9
TXBYTEOK8
Name
Default
0
0
0
0
0
0
0
0
030Fh:
Bit #
07
06
05
04
03
02
01
00
TXBYTEOK7
TXBYTEOK6
TXBYTEOK5
TXBYTEOK4
TXBYTEOK3
TXBYTEOK2
TXBYTEOK1
TXBYTEOK0
Name
Default
0
0
0
0
0
0
0
0
Bits 0 - 31: Bytes Transmitted OK Counter (TXBYTEOK[0:31]) 32 bit value indicating the number of bytes
transmitted and determined to be valid. Each time a valid byte is transmitted, this counter is incremented by 1. This
counter resets only upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value.
The user should ensure that the measurement period is less than the minimum length of time required for the
counter to increment 2^32-1 times at the maximum frame rate. The user should store the value from the beginning
of the measurement period for later calculations, and take into account the possibility of a roll-over to occurring.
198 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.TxFrmUndr
Register Description:
Register Address:
MAC Transmit Frame Under Run Counter
0334h (indirect)
0334h:
Bit #
Name
Default
31
TXFRMU31
0
30
TXFRMU30
0
29
TXFRMU29
0
28
TXFRMU28
0
27
TXFRMU27
0
26
TXFRMU26
0
25
TXFRMU25
0
24
TXFRMU24
0
0335h:
Bit #
Name
Default
23
TXFRMU23
0
22
TXFRMU22
0
21
TXFRMU21
0
20
TXFRMU20
0
19
TXFRMU19
0
18
TXFRMU18
0
17
TXFRMU17
0
16
TXFRMU16
0
0336h:
Bit #
Name
Default
15
TXFRMU15
0
14
TXFRMU14
0
13
TXFRMU13
0
12
TXFRMU12
0
11
TXFRMU11
0
10
TXFRMU10
0
09
TXFRMU9
0
08
TXFRMU8
0
0337h:
Bit #
Name
Default
07
06
05
TXFRMU5
0
04
TXFRMU4
0
03
TXFRMU3
0
02
TXFRMU2
0
01
TXFRMU1
0
00
TXFRMU0
0
TXFRMU7 TXFRMU6
0
0
Bits 0 - 31: Frames Aborted Due to FIFO Under Run Counter (TXFRMU[0:31]) 32 bit value indicating the
number of frames aborted due to FIFO under run. Each time a frame is aborted due to FIFO under run, this
counter is incremented by 1. This counter resets only upon device reset, does not saturate, and rolls-over to zero
upon reaching the maximum value. The user should ensure that the measurement period is less than the minimum
length of time required for the counter to increment 2^32-1 times at the maximum frame rate. The user should store
the value from the beginning of the measurement period for later calculations, and take into account the possibility
of a roll-over to occurring.
199 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
SU.TxBdFrmCtr
Register Description:
Register Address:
MAC All Frames Aborted Counter
0338h (indirect)
0338h:
Bit #
31
30
29
28
27
26
25
24
TXFRMBD31 TXFRMBD30 TXFRMBD29 TXFRMBD28 TXFRMBD27 TXFRMBD26 TXFRMBD25 TXFRMBD24
Name
Default
0
0
0
0
0
0
0
0
0339h:
Bit #
23
22
21
20
19
18
17
16
TXFRMBD23 TXFRMBD22 TXFRMBD21 TXFRMBD20 TXFRMBD19 TXFRMBD18 TXFRMBD17 TXFRMBD16
Name
Default
0
0
0
0
0
0
0
0
033Ah:
Bit #
Name
Default
15
14
13
12
11
10
09
TXFRMBD9
0
08
TXFRMBD8
0
TXFRMBD15 TXFRMBD14 TXFRMBD13 TXFRMBD12 TXFRMBD11 TXFRMBD10
0
0
0
0
0
0
033Bh:
Bit #
Name
Default
07
TXFRMBD7
0
06
TXFRMBD6
0
05
TXFRMBD5
0
04
TXFRMBD4
0
03
TXFRMBD3
0
02
TXFRMBD2
0
01
TXFRMBD1
0
00
TXFRMBD0
0
Bits 0 to 31: All Frames Aborted Counter (TXFRMBD[0:31]) 32 bit value indicating the number of frames
aborted due to any reason. Each time a frame is aborted, this counter is incremented by 1. This counter resets only
upon device reset, does not saturate, and rolls-over to zero upon reaching the maximum value. The user should
ensure that the measurement period is less than the minimum length of time required for the counter to increment
2^32-1 times at the maximum frame rate. The user should store the value from the beginning of the measurement
period for later calculations, and take into account the possibility of a roll-over to occurring.
200 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.7 T1/E1/J1 Transceiver Registers
Register Name:
Register Description:
Register Address:
TR.MSTRREG
Master Mode Register
00h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
TEST1
0
2
TEST0
0
1
T1/E1
0
0
SFTRST
0
Bits 2 – 3: Test Mode Bits (TEST0, TEST1) Test modes are used to force the output pins of the transceiver into
known states. This can facilitate the checkout of assemblies during the manufacturing process and also be used to
isolate devices from shared buses.
TEST1
TEST0
Effect On Output Pins
0
0
Operate normally
0
1
1
1
0
1
Force all output pins into tri-state (including all I/O pins and parallel port pins)
Force all output pins low (including all I/O pins except parallel port pins)
Force all output pins high (including all I/O pins except parallel port pins)
Bit 1: Transceiver Operating Mode (T1/E1) Used to select the operating mode of the framer/formatter (digital)
portion of the Transceiver. The operating mode of the LIU must also be programmed.
0 = T1 operation
1 = E1 operation
Bit 0: Software-Issued Reset (SFTRST) A 0-to-1 transition causes the register space in the T1/E1/J1 transceiver
to be cleared. A reset clears all configuration and status registers. The bit automatically clears itself when the reset
has completed.
201 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IOCR1
Register Description:
Register Address:
I/O Configuration Register 1
01h
Bit #
Name
Default
7
RSMS
0
6
RSMS2
0
5
RSMS1
0
4
RSIO
0
3
TSDW
0
2
TSM
0
1
TSIO
0
0
ODF
0
Bit 7: RSYNC Multiframe Skip Control (RSMS) Useful in framing format conversions from D4 to ESF. This
function is not available when the receive-side elastic store is enabled. RSYNC must be set to output multiframe
pulses (TR.IOCR1.5 = 1 and TR.IOCR1.4 = 0).
0 = RSYNC outputs a pulse at every multiframe
1 = RSYNC outputs a pulse at every other multiframe
Bit 6: RSYNC Mode Select 2 (RSMS2)
T1 Mode: RSYNC pin must be programmed in the output frame mode (TR.IOCR1.5 = 0, TR.IOCR1.4 = 0).
0 = do not pulse double-wide in signaling frames
1 = do pulse double-wide in signaling frames
E1 Mode: RSYNC pin must be programmed in the output multiframe mode (TR.IOCR1.5 = 1, TR.IOCR1.4
= 0).
0 = RSYNC outputs CAS multiframe boundaries
1 = RSYNC outputs CRC4 multiframe boundaries
Bit 5: RSYNC Mode Select 1(RSMS1) Selects frame or multiframe pulse when RSYNC pin is in output mode. In
input mode (elastic store must be enabled), multiframe mode is only useful when receive signaling reinsertion is
0 = frame mode
1 = multiframe mode
Bit 4: RSYNC I/O Select (RSIO) (Note: This bit must be set to 0 when TR.ESCR.0 = 0.)
0 = RSYNC is an output
1 = RSYNC is an input (only valid if elastic store enabled)
Bit 3: TSYNC Double-Wide (TSDW) (Note: This bit must be set to 0 when TR.IOCR1.2 = 1 or when TR.IOCR1.1
= 0.)
0 = do not pulse double-wide in signaling frames
1 = do pulse double-wide in signaling frames
Bit 2: TSYNC Mode Select (TSM) Selects frame or multiframe mode for the TSYNC pin. See the timing diagrams
0 = frame mode
1 = multiframe mode
Bit 1: TSYNC I/O Select (TSIO)
0 = TSYNC is an input
1 = TSYNC is an output
Bit 0: Output Data Format (ODF)
0 = bipolar data at TPOSO and TNEGO
1 = NRZ data at TPOSO; TNEGO = 0
202 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IOCR2
Register Description:
Register Address:
I/O Configuration Register 2
02h
Bit #
Name
Default
7
RCLKINV
0
6
TCLKINV
0
5
4
3
2
1
0
RSYNCINV TSYNCINV TSSYNCINV
H100EN TSCLKM RSCLKM
0
0
0
0
0
0
Bit 7: RCLKO Invert (RCLKINV)
0 = no inversion
1 = inverts signal on RCLKO output.
Bit 6: TCLKT Invert (TCLKINV)
0 = no inversion
1 = inverts signal on TCLKT input.
Bit 5: RSYNC Invert (RSYNCINV)
0 = no inversion
1 = invert
Bit 4: TSYNC Invert (TSYNCINV)
0 = no inversion
1 = invert
Bit 3: TSSYNC Invert (TSSYNCINV)
0 = no inversion
1 = invert
Bit 2 : H.100 SYNC Mode (H100EN)
0 = normal operation
1 = SYNC shift
Bit 1: TSYSCLK Mode Select (TSCLKM)
0 = if TSYSCLK is 1.544MHz
1 = if TSYSCLK is 2.048MHz
Bit 0: RSYSCLK Mode Select (RSCLKM)
0 = if RSYSCLK is 1.544MHz
1 = if RSYSCLK is 2.048MHz
203 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.T1RCR1
Register Description:
Register Address:
T1 Receive Control Register 1
03h
Bit #
Name
Default
7
—
0
6
ARC
0
5
OOF1
0
4
OOF2
0
3
SYNCC
0
2
SYNCT
0
1
SYNCE
0
0
RESYNC
0
Bit 6: Auto Resync Criteria (ARC)
0 = resync on OOF or RCL event
1 = resync on OOF only
Bits 4- 5: Out-of-Frame Select Bits (OOF2, OOF1)
OOF2
OOF1
Out-Of-Frame Criteria
2/4 frame bits in error
2/5 frame bits in error
2/6 frame bits in error
2/6 frame bits in error
0
0
1
1
0
1
0
1
Bit 3: Sync Criteria (SYNCC)
In D4 Framing Mode:
0 = search for Ft pattern, then search for Fs pattern
1 = cross couple Ft and Fs pattern
In ESF Framing Mode:
0 = search for FPS pattern only
1 = search for FPS and verify with CRC6
Bit 2: Sync Time (SYNCT)
0 = qualify 10 bits
1 = qualify 24 bits
Bit 1: Sync Enable (SYNCE)
0 = auto resync enabled
1 = auto resync disabled
Bit 0: Resynchronize (RESYNC) When toggled from low to high, a resynchronization of the receive-side framer
is initiated. Must be cleared and set again for a subsequent resync.
204 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.T1RCR2
Register Description:
Register Address:
T1 Receive Control Register 2
04h
Bit #
Name
Default
7
—
0
6
RFM
0
5
RB8ZS
0
4
RSLC96
0
3
RZSE
0
2
—
0
1
RJC
0
0
RD4YM
0
Bit 6: Receive Frame Mode Select (RFM)
0 = D4 framing mode
1 = ESF framing mode
Bit 5: Receive B8ZS Enable (RB8ZS)
0 = B8ZS disabled
1 = B8ZS enabled
Bit 4: Receive SLC-96 Enable (RSLC96). Only set this bit to a 1 in D4/SLC-96 framing applications. See Section
10.18 for details.
0 = SLC-96 disabled
1 = SLC-96 enabled
Bit 3: Receive FDL Zero-Destuffer Enable (RZSE). Set this bit to 0 if using the internal HDLC/BOC controller
0 = zero destuffer disabled
1 = zero destuffer enabled
Bit 2: Reserved. Set to zero for proper operation.
Bit 1: Receive Japanese CRC6 Enable (RJC)
0 = use ANSI/AT&T/ITU CRC6 calculation (normal operation)
1 = use Japanese standard JT–G704 CRC6 calculation
Bit 0: Receive-Side D4 Yellow Alarm Select (RD4YM)
0 = 0s in bit 2 of all channels
1 = a 1 in the S-bit position of frame 12 (J1 Yellow Alarm Mode)
205 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.T1TCR1
Register Description:
Register Address:
T1 Transmit Control Register 1
05h
Bit #
Name
Default
7
TJC
0
6
TFPT
0
5
TCPT
0
4
TSSE
0
3
GB7S
0
2
TFDLS
0
1
TBL
0
0
TYEL
0
Bit 7: Transmit Japanese CRC6 Enable (TJC)
0 = use ANSI/AT&T/ITU CRC6 calculation (normal operation)
1 = use Japanese standard JT–G704 CRC6 calculation
Bit 6: Transmit F-Bit Pass-Through (TFPT)
0 = F bits sourced internally
1 = F bits sampled at TSERI
Bit 5: Transmit CRC Pass-Through (TCPT)
0 = source CRC6 bits internally
1 = CRC6 bits sampled at TSERI during F-bit time
Bit 4: Transmit Software Signaling Enable (TSSE).
0 = do not source signaling data from the TR.TSx registers regardless of the TR.SSIEx registers. The
TR.SSIEx registers still define which channels are to have B7 stuffing preformed.
1 = source signaling data as enabled by the TR.SSIEx registers
Bit 3: Global Bit 7 Stuffing (GB7S)
0 = allow the SSIEx registers to determine which channels containing all 0s are to be bit 7 stuffed
1 = force bit 7 stuffing in all 0-byte channels regardless of how the TR.SSIEx registers are programmed
Bit 2: TFDL Register Select (TFDLS)
0 = source FDL or Fs-bits from the internal TR.TFDL register (legacy FDL support mode)
1 = source FDL or Fs-bits from the internal HDLC controller
Bit 1: Transmit Blue Alarm (TBL)
0 = transmit data normally
1 = transmit an unframed all-ones code at TPOS and TNEG
Bit 0: Transmit Yellow Alarm (TYEL)
0 = do not transmit yellow alarm
1 = transmit yellow alarm
206 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.T1TCR2
Register Description:
Register Address:
T1 Transmit Control Register 2
06h
Bit #
Name
Default
7
TB8ZS
0
6
TSLC96
0
5
TZSE
0
4
FBCT2
0
3
FBCT1
0
2
TD4YM
0
1
—
0
0
TB7ZS
0
Bit 7: Transmit B8ZS Enable (TB8ZS)
0 = B8ZS disabled
1 = B8ZS enabled
Bit 6: Transmit SLC-96/Fs-Bit Insertion Enable (TSLC96). Only set this bit to a 1 in D4 framing applications.
0 = SLC-96/Fs-bit insertion disabled
1 = SLC-96/Fs-bit insertion enabled
Bit 5: Transmit FDL Zero-Stuffer Enable (TZSE). Set this bit to 0 if using the internal HDLC controller instead of
the legacy support for the FDL. See Section 15 for details.
0 = zero stuffer disabled
1 = zero stuffer enabled
Bit 4: F-Bit Corruption Type 2 (FBCT2). Setting this bit high enables the corruption of one Ft (D4 framing mode)
or FPS (ESF framing mode) bit in every 128 Ft or FPS bits as long as the bit remains set.
Bit 3: F-Bit Corruption Type 1 (FBCT1). A low-to-high transition of this bit causes the next three consecutive Ft
(D4 framing mode) or FPS (ESF framing mode) bits to be corrupted causing the remote end to experience a loss of
synchronization.
Bit 2: Transmit-Side D4 Yellow Alarm Select (TD4YM)
0 = 0s in bit 2 of all channels
1 = a 1 in the S-bit position of frame 12
Bit 0: Transmit-Side Bit 7 Zero-Suppression Enable (TB7ZS)
0 = no stuffing occurs
1 = bit 7 forced to a 1 in channels with all 0s
207 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.T1CCR1
Register Description:
Register Address:
T1 Common Control Register 1
07h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
TRAI-CI
0
3
TAIS-CI
0
2
TFM
0
1
PDE
0
0
TLOOP
0
Bit 4: Transmit RAI-CI Enable (TRAI-CI). Setting this bit causes the ESF RAI-CI code to be transmitted in the
FDL bit position.
0 = do not transmit the ESF RAI-CI code
1 = transmit the ESF RAI-CI code
Bit 3: Transmit AIS-CI Enable (TAIS-CI). Setting this bit and the TBL bit (TR.T1TCR1.1) causes the AIS-CI code
to be transmitted at TPOSO and TNEGO, as defined in ANSI T1.403.
0 = do not transmit the AIS-CI code
1 = transmit the AIS-CI code (TR.T1TCR1.1 must also be set = 1)
Bit 2: Transmit Frame Mode Select (TFM)
0 = D4 framing mode
1 = ESF framing mode
Bit 1: Pulse Density Enforcer Enable (PDE). The framer always examines the transmit and receive data streams
for violations of these, which are required by ANSI T1.403: No more than 15 consecutive 0s and at least N 1s in
each and every time window of 8 x (N + 1) bits, where N = 1 through 23. Violations for the transmit and receive
data streams are reported in the TR.INFO1.6 and TR.INFO1.7 bits, respectively. When this bit is set to 1, the
T1/E1/J1 transceiver forces the transmitted stream to meet this requirement no matter the content of the
transmitted stream. When running B8ZS, this bit should be set to 0 since B8ZS encoded data streams cannot
violate the pulse density requirements.
0 = disable transmit pulse density enforcer
1 = enable transmit pulse density enforcer
0 = transmit data normally
1 = replace normal transmitted data with repeating code as defined in registers TR.TCD1 and TR.TCD2
Register Name:
TR.SSIE1 (T1 Mode)
Register Description:
Register Address:
Software Signaling Insertion Enable 1
08h
Bit #
Name
Default
7
CH8
0
6
CH7
0
5
CH6
0
4
CH5
0
3
CH4
0
2
CH3
0
1
CH2
0
0
CH1
0
Bits 0 – 7: Software Signaling Insertion Enable for Channels 1 to 8 (CH1 to CH8). These bits determine which
channels are to have signaling inserted from the transmit signaling registers.
0 = do not source signaling data from the TR.TSx registers for this channel
1 = source signaling data from the TR.TSx registers for this channel
208 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SSIE1 (E1 Mode)
Register Description:
Register Address:
Software Signaling Insertion Enable 1
08h
Bit #
Name
Default
7
CH7
0
6
CH6
0
5
CH5
0
4
CH4
0
3
CH3
0
2
CH2
0
1
CH1
0
0
UCAW
0
Bits 1 – 7: Software Signaling-Insertion Enable for Channels 1 to 7 (CH1 to CH7). These bits determine which
channels are to have signaling inserted from the transmit signaling registers.
0 = do not source signaling data from the TR.TSx registers for this channel
1 = source signaling data from the TR.TSx registers for this channel
Bit 0: Upper CAS Align/Alarm Word (UCAW). Selects the upper CAS align/alarm pattern (0000) to be sourced
from the upper 4 bits of the TS1 register.
0 = do not source the upper CAS align/alarm pattern from the TR.TS1 register
1 = source the upper CAS align/alarm pattern from the TR.TS1 register
Register Name:
TR.SSIE2 (T1 Mode)
Register Description:
Register Address:
Software Signaling-Insertion Enable 2
09h
Bit #
Name
Default
7
CH16
0
6
CH15
0
5
CH14
0
4
CH13
0
3
CH12
0
2
CH11
0
1
CH10
0
0
CH9
0
Bits 0 – 7: Software Signaling Insertion Enable for Channels 9 to 16 (CH9 to CH16). These bits determine
which channels are to have signaling inserted from the transmit signaling registers.
0 = do not source signaling data from the TR.TSx registers for this channel
1 = source signaling data from the TR.TSx registers for this channel
Register Name:
TR.SSIE2 (E1 Mode)
Register Description:
Register Address:
Software Signaling Insertion Enable 2
09h
Bit #
Name
Default
7
CH15
0
6
CH14
0
5
CH13
0
4
CH12
0
3
CH11
0
2
CH10
0
1
CH9
0
0
CH8
0
Bits 0 – 7: Software Signaling Insertion Enable for Channels 8 to 15 (CH8 to CH15). These bits determine
which channels are to have signaling inserted from the transmit signaling registers.
0 = do not source signaling data from the TR.TSx registers for this channel
1 = source signaling data from the TR.TSx registers for this channel
209 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SSIE3 (T1 Mode)
Register Description:
Register Address:
Software Signaling-Insertion Enable 3
0Ah
Bit #
Name
Default
7
CH24
0
6
CH23
0
5
CH22
0
4
CH21
0
3
CH20
0
2
CH19
0
1
CH18
0
0
CH17
0
Bits 0 – 7: Software Signaling Insertion Enable for Channels 17 to 24 (CH17 to CH24). These bits determine
which channels are to have signaling inserted from the transmit signaling registers.
0 = do not source signaling data from the TR.TSx registers for this channel
1 = source signaling data from the TR.TSx registers for this channel
Register Name:
TR.SSIE3 (E1 Mode)
Register Description:
Register Address:
Software Signaling Insertion Enable 3
0Ah
Bit #
Name
Default
7
CH22
0
6
CH21
0
5
CH20
0
4
CH19
0
3
CH18
0
2
CH17
0
1
CH16
0
0
LCAW
0
Bits 1 – 7: Software Signaling Insertion Enable for LCAW and Channels 16 to 22 (CH16 to CH22). These bits
determine which channels are to have signaling inserted from the transmit signaling registers.
0 = do not source signaling data from the TR.TSx registers for this channel
1 = source signaling data from the TR.TSx registers for this channel
Bit 0: Lower CAS Align/Alarm Word (LCAW). Selects the lower CAS align/alarm bits (xyxx) to be sourced from
the lower 4 bits of the TS1 register.
0 = do not source the lower CAS align/alarm bits from the TR.TS1 register
1 = source the lower CAS alarm align/bits from the TR.TS1 register
Register Name:
TR.SSIE4
Register Description:
Register Address:
Software Signaling Insertion Enable 4
0Bh
Bit #
Name
Default
7
CH30
0
6
CH29
0
5
CH28
0
4
CH27
0
3
CH26
0
2
CH25
0
1
CH24
0
0
CH23
0
Bits 0 – 7: Software Signaling Insertion Enable for Channels 22 to 30 (CH23 to CH30). These bits determine
which channels are to have signaling inserted from the transmit signaling registers.
0 = do not source signaling data from the TR.TSx registers for this channel
1 = source signaling data from the TR.TSx registers for this channel
210 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.T1RDMR1
Register Description:
Register Address:
T1 Receive Digital-Milliwatt Enable Register 1
0Ch
Bit #
Name
Default
7
CH8
0
6
CH7
0
5
CH6
0
4
CH5
0
3
CH4
0
2
CH3
0
1
CH2
0
0
CH1
0
Bits 0 - 7: Receive Digital-Milliwatt Enable for Channels 1 to 8 (CH1 to CH8)
0 = do not affect the receive data associated with this channel
1 = replace the receive data associated with this channel with digital-milliwatt code
Register Name:
TR.T1RDMR2
Register Description:
Register Address:
T1 Receive Digital-Milliwatt Enable Register 2
0Dh
Bit #
Name
Default
7
CH16
0
6
CH15
0
5
CH14
0
4
CH13
0
3
CH12
0
2
CH11
0
1
CH10
0
0
CH9
0
Bits 0 - 7: Receive Digital-Milliwatt Enable for Channels 9 to 16 (CH9 to CH16)
0 = do not affect the receive data associated with this channel
1 = replace the receive data associated with this channel with digital-milliwatt code
Register Name:
TR.T1RDMR3
Register Description:
Register Address:
T1 Receive Digital-Milliwatt Enable Register 3
0Eh
Bit #
Name
Default
7
CH24
0
6
CH23
0
5
CH22
0
4
CH21
0
3
CH20
0
2
CH19
0
1
CH18
0
0
CH17
0
Bits 0 - 7: Receive Digital-Milliwatt Enable for Channels 17 to 24 (CH17 to CH24)
0 = do not affect the receive data associated with this channel
1 = replace the receive data associated with this channel with digital-milliwatt code
211 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IDR
Register Description:
Register Address:
Device Identification Register
0Fh
Bit #
Name
Default
7
ID7
1
6
ID6
0
5
ID5
1
4
ID4
1
3
ID3
X
2
ID2
X
1
ID1
X
0
ID0
X
Bits 4 - 7: Device ID (ID4 to ID7). The upper four bits of TR.IDR are used to display the transceiver ID.
Bits 0 – 3: Chip Revision Bits (ID0 to ID3). The lower four bits of TR.IDR are used to display the die revision of
the chip. IDO is the LSB of a decimal code that represents the chip revision.
Register Name:
TR.INFO1
Register Description:
Register Address:
Information Register 1
10h
Bit #
Name
Default
7
RPDV
0
6
TPDV
0
5
COFA
0
4
8ZD
0
3
16ZD
0
2
SEFE
0
1
B8ZS
0
0
FBE
0
Bit 7: Receive Pulse-Density Violation Event (RPDV). Set when the receive data stream does not meet the
ANSI T1.403 requirements for pulse density.
Bit 6: Transmit Pulse-Density Violation Event (TPDV). Set when the transmit data stream does not meet the
ANSI T1.403 requirements for pulse density.
Bit 5: Change-of-Frame Alignment Event (COFA). Set when the last resync resulted in a change-of-frame or
multiframe alignment.
Bit 4: Eight Zero-Detect Event (8ZD). Set when a string of at least eight consecutive 0s (regardless of the length
of the string) have been received at RPOSI and RNEGI.
Bit 3: Sixteen Zero-Detect Event (16ZD). Set when a string of at least 16 consecutive 0s (regardless of the length
of the string) have been received at RPOSI and RNEGI.
Bit 2: Severely Errored Framing Event (SEFE). Set when two out of six framing bits (Ft or FPS) are received in
error.
Bit 1: B8ZS Codeword Detect Event (B8ZS). Set when a B8ZS codeword is detected at RPOS and RNEG
independent of whether the B8ZS mode is selected or not by TR.T1TCR2.7. Useful for automatically setting the
line coding.
Bit 0: Frame Bit-Error Event (FBE). Set when an Ft (D4) or FPS (ESF) framing bit is received in error.
212 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.INFO2
Register Description:
Register Address:
Information Register 2
11h
Bit #
Name
Default
7
BSYNC
0
6
BD
0
5
TCLE
0
4
TOCD
0
3
RL3
0
2
RL2
0
1
RL1
0
0
RL0
0
Bit 7: BERT Real-Time Synchronization Status (BSYNC). Real-time status of the synchronizer (this bit is not
latched). This bit is set when the incoming pattern matches for 32 consecutive bit positions. It is cleared when six
or more bits out of 64 are received in error. Refer to BSYNC in the BERT status register, TR.SR9, for an interrupt-
generating version of this signal.
Bit 6: BOC Detected (BD). A real-time bit that is set high when the BOC detector is presently seeing a valid
sequence and set low when no BOC is currently being detected.
Bit 5: Transmit Current-Limit Exceeded (TCLE). A real-time bit that is set when the 50mA (RMS) current limiter
is activated, whether the current limiter is enabled or not.
Bit 4: Transmit Open-Circuit Detect (TOCD). A real-time bit that is set when the device detects that the TTIP and
TRING outputs are open-circuited.
Bits 0 – 3: Receive Level Bits (RL0 to RL3). Real-time bits
RL3
0
0
RL2
0
0
RL1
0
0
RL0
0
1
Receive Level (dB)
Greater than -2.5
-2.5 to -5.0
0
0
1
0
-5.0 to -7.5
0
0
1
1
-7.5 to -10.0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
-10.0 to -12.5
-12.5 to -15.0
-15.0 to -17.5
-17.5 to -20.0
-20.0 to -22.5
-22.5 to -25.0
-25.0 to -27.5
-27.5 to -30.0
-30.0 to -32.5
-32.5 to -35.0
-35.0 to -37.5
Less than -37.5
NOTE: RL0 through RL3 only indicate the signal range as specified by the EGL bit in TR.LIC1. Example; if EGL =
1 and in T1 mode, RL0 through RL3 will only indicate a signal range of >-2.5dB to –15dB even if the signal is < -
15dB.
213 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.INFO3
Register Description:
Register Address:
Information Register 3
12h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
—
0
2
CRCRC
0
1
FASRC
0
0
CASRC
0
Bit 2: CRC Resync Criteria Met Event (CRCRC). Set when 915/1000 codewords are received in error.
Bit 1: FAS Resync Criteria Met Event (FASRC). Set when three consecutive FAS words are received in error.
Note: During a CRC resync the FAS synchronizer is brought online to verify the FAS alignment. If during this
process an FAS emulator exists, the FAS synchronizer may temporarily align to the emulator. The FASRC will go
active indicating a search for a valid FAS has been activated.
Bit 0: CAS Resync Criteria Met Event (CASRC). Set when two consecutive CAS MF alignment words are
received in error.
Register Name:
TR.IIR1
Register Description:
Register Address:
Interrupt Information Register 1
14h
Bit #
Name
Default
7
SR8
0
6
SR7
0
5
SR6
0
4
SR5
0
3
SR4
0
2
SR3
0
1
SR2
0
0
SR1
0
Bits 0 – 7: Status Register 1 – 8 (SR1–SR8). When set to 1, these bits indicate that an enabled interrupt is active
in the associated T1/E1/J1 status register.
Register Name:
TR.IIR2
Register Description:
Register Address:
Interrupt Information Register 2
15h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
—
0
2
—
0
1
—
0
0
SR9
0
Bits 0: Status Register 9 (SR9). When set to 1, this bit indicates that an enabled interrupt is active in the
associated T1/E1/J1 status register.
214 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR1
Register Description:
Register Address:
Status Register 1
16h
Bit #
Name
Default
7
ILUT
0
6
TIMER
0
5
RSCOS
0
4
JALT
0
3
LRCL
0
2
TCLE
0
1
TOCD
0
0
LOLITC
0
Bit 7: Input Level Under Threshold (ILUT). This bit is set whenever the input level at RTIP and RRING falls
below the threshold set by the value in TR.CCR4.4 through TR.CCR4.7. The level must remain below the
programmed threshold for approximately 50ms for this bit to be set. This is a double interrupt bit (Section 9.7).
Bit 6: Timer Event (TIMER). Follows the error-counter update interval as determined by the ECUS bit in the error-
counter configuration register (TR.ERCNT).
T1: set on increments of 1 second or 42ms based on RCLKO
E1: set on increments of 1 second or 62.5ms based on RCLKO
Bit 5: Receive Signaling Change-of-State Event (RSCOS). Set when any channel selected by the receive
signaling change-of-state interrupt-enable registers (TR.RSCSE1 through TR.RSCSE4) changes signaling state.
Bit 4: Jitter Attenuator Limit Trip Event (JALT). Set when the jitter attenuator FIFO reaches to within 4 bits of its
useful limit. This bit is cleared when read. Useful for debugging jitter attenuation operation.
Bit 3: Line Interface Receive Carrier-Loss Condition (LRCL). Set when the carrier signal is lost. This is a
Bit 2: Transmit Current-Limit Exceeded Condition (TCLE). Set when the 50mA (RMS) current limiter is
activated, whether the current limiter is enabled or not. This is a double interrupt bit (Section 9.7).
Bit 1: Transmit Open-Circuit Detect Condition (TOCD). Set when the device detects that the TTIP and TRING
Bit 0: Loss of Line-Interface Transmit-Clock Condition (LOLITC). Set when TDCLKI has not transitioned for
215 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IMR1
Register Description:
Register Address:
Interrupt Mask Register 1
17h
Bit #
Name
Default
7
ILUT
0
6
TIMER
0
5
RSCOS
0
4
JALT
0
3
LRCL
0
2
TCLE
0
1
TOCD
0
0
LOLITC
0
Bit 7: Input Level Under Threshold (ILUT)
0 = interrupt masked
1 = interrupt enabled
Bit 6: Timer Event (TIMER)
0 = interrupt masked
1 = interrupt enabled
Bit 5: Receive Signaling Change-of-State Event (RSCOS)
0 = interrupt masked
1 = interrupt enabled
Bit 4: Jitter Attenuator Limit Trip Event (JALT)
0 = interrupt masked
1 = interrupt enabled
Bit 3: Line Interface Receive Carrier-Loss Condition (LRCL)
0 = interrupt masked
1 = interrupt enabled—generates interrupts on rising and falling edges
Bit 2: Transmit Current-Limit Exceeded Condition (TCLE)
0 = interrupt masked
1 = interrupt enabled—generates interrupts on rising and falling edges
Bit 1: Transmit Open-Circuit Detect Condition (TOCD)
0 = interrupt masked
1 = interrupt enabled—generates interrupts on rising and falling edges
Bit 0: Loss-of-Transmit Clock Condition (LOLITC)
0 = interrupt masked
1 = interrupt enabled—generates interrupts on rising and falling edges
216 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR2
Register Description:
Register Address:
Status Register 2
18h
Bit #
Name
Default
7
RYELC
0
6
RUA1C
0
5
FRCLC
0
4
RLOSC
0
3
RYEL
0
2
RUA1
0
1
FRCL
0
0
RLOS
0
Bit 7: Receive Yellow Alarm Clear Event (RYELC) (T1 Only). Set when the receive Yellow Alarm condition is no
longer detected.
Bit 6: Receive Unframed All-Ones Clear Event (RUA1C). Set when the unframed all 1s condition is no longer
detected.
Bit 5: Framer Receive Carrier-Loss Clear Event (FRCLC). Set when the carrier loss condition at RPOSI and
RNEGI is no longer detected.
Bit 4: Receive Loss-of-Sync Clear Event (RLOSC). Set when the framer achieves synchronization; remains set
until read.
Bit 3: Receive Yellow Alarm Condition (RYEL) (T1 Only). Set when a Yellow Alarm is received at RPOSI and
RNEGI.
Bit 2: Receive Unframed All-Ones (T1 Blue Alarm, E1 AIS) Condition (RUA1). Set when an unframed all 1s
code is received at RPOSI and RNEGI.
Bit 1: Framer Receive Carrier-Loss Condition (FRCL). Set when 255 (or 2048 if TR.E1RCR2.0 = 1) E1 mode or
192 T1 mode consecutive 0s have been detected at RPOSI and RNEGI.
Bit 0: Receive Loss-of-Sync Condition (RLOS). Set when the transceiver is not synchronized to the received
data stream.
217 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IMR2
Register Description:
Register Address:
Interrupt Mask Register 2
19h
Bit #
Name
Default
7
RYELC
0
6
RUA1C
0
5
FRCLC
0
4
RLOSC
0
3
RYEL
0
2
RUA1
0
1
FRCL
0
0
RLOS
0
Bit 7: Receive Yellow Alarm Clear Event (RYELC)
0 = interrupt masked
1 = interrupt enabled
Bit 6: Receive Unframed All-Ones Condition Clear Event (RUA1C)
0 = interrupt masked
1 = interrupt enabled
Bit 5: Framer Receive Carrier Loss Condition Clear (FRCLC)
0 = interrupt masked
1 = interrupt enabled
Bit 4: Receive Loss-of-Sync Clear Event (RLOSC)
0 = interrupt masked
1 = interrupt enabled
Bit 3: Receive Yellow Alarm Condition (RYEL)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
Bit 2: Receive Unframed All-Ones (Blue Alarm) Condition (RUA1)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
Bit 1: Framer Receive Carrier Loss Condition (FRCL)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
Bit 0: Receive Loss-of-Sync Condition (RLOS)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
218 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR3
Register Description:
Register Address:
Status Register 3
1Ah
Bit #
Name
Default
7
LSPARE
0
6
LDN
0
5
LUP
0
4
LOTC
0
3
LORC
0
2
V52LNK
0
1
RDMA
0
0
RRA
0
Bit 7: Spare Code Detected Condition (LSPARE) (T1 Only). Set when the spare code as defined in the
TR.RSCD1/2 registers is being received. See Section 10.19 for details. This is a double interrupt bit. See Section
9.7.
Bit 6: Loop-Down Code Detected Condition (LDN) (T1 Only). Set when the loop down code as defined in the
TR.RDNCD1/2 register is being received. See Section 10.19 for details. This is a double interrupt bit. See Section
9.7.
Bit 5: Loop-Up Code Detected Condition (LUP) (T1 Only). Set when the loop-up code as defined in the
TR.RUPCD1/2 register is being received. See Section 10.19 for details. This is a double interrupt bit. See Section
9.7.
Bit 4: Loss-of-Transmit Clock Condition (LOTC). Set when the TCLKT pin has not transitioned for one channel
time. Forces the LOTC pin high if enabled by TR.CCR1.0. This is a double interrupt bit. See Section 9.7.
Bit 3: Loss-of-Receive Clock Condition (LORC). Set when the RDCLKI pin has not transitioned for one channel
Bit 2: V5.2 Link Detected Condition (V52LNK) (E1 Only). Set on detection of a V5.2 link identification signal
Bit 1: Receive Distant MF Alarm Condition (RDMA) (E1 Only). Set when bit 6 of time slot 16 in frame 0 has
been set for two consecutive multiframes. This alarm is not disabled in the CCS signaling mode. This is a double
Bit 0: Receive Remote Alarm Condition (RRA) (E1 Only). Set when a remote alarm is received at RPOSI and
219 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IMR3
Register Description:
Register Address:
Interrupt Mask Register 3
1Bh
Bit #
Name
Default
7
LSPARE
0
6
LDN
0
5
LUP
0
4
LOTC
0
3
LORC
0
2
V52LNK
0
1
RDMA
0
0
RRA
0
Bit 7: Spare Code Detected Condition (LSPARE)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 6: Loop-Down Code-Detected Condition (LDN)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 5: Loop-Up Code-Detected Condition (LUP)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 4: Loss-of-Transmit Clock Condition (LOTC)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 3: Loss-of-Receive Clock Condition (LORC)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 2: V5.2 Link Detected Condition (V52LNK)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 1: Receive Distant MF Alarm Condition (RDMA)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 0: Receive Remote Alarm Condition (RRA)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
220 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR4
Register Description:
Register Address:
Status Register 4
1Ch
Bit #
Name
Default
7
RAIS-CI
0
6
RSAO
0
5
RSAZ
0
4
TMF
0
3
TAF
0
2
RMF
0
1
RCMF
0
0
RAF
0
Bit 7: Receive AIS-CI Event (RAIS-CI) (T1 Only). Set when the receiver detects the AIS-CI pattern as defined in
ANSI T1.403.
Bit 6: Receive Signaling All-Ones Event (RSAO) (E1 Only). Set when the contents of time slot 16 contains fewer
than three 0s over 16 consecutive frames. This alarm is not disabled in the CCS signaling mode.
Bit 5: Receive Signaling All-Zeros Event (RSAZ) (E1 Only). Set when over a full MF, time slot 16 contains
all 0s.
Bit 4: Transmit Multiframe Event (TMF)
E1 Mode: Set every 2ms (regardless if CRC4 is enabled) on transmit multiframe boundaries. Used to alert
the host that signaling data needs to be updated.
T1 Mode: Set every 1.5ms on D4 MF boundaries or every 3ms on ESF MF boundaries.
Bit 3: Transmit Align Frame Event (TAF) (E1 Only). Set every 250μs at the beginning of align frames. Used to
alert the host that the TR.TAF and TR.TNAF registers need to be updated.
Bit 2: Receive Multiframe Event (RMF)
E1 Mode: Set every 2ms (regardless if CAS signaling is enabled or not) on receive multiframe boundaries.
Used to alert the host that signaling data is available.
T1 Mode: Set every 1.5ms on D4 MF boundaries or every 3ms on ESF MF boundaries.
Bit 1: Receive CRC4 Multiframe Event (RCMF) (E1 Only). Set on CRC4 multiframe boundaries; continues to set
every 2ms on an arbitrary boundary if CRC4 is disabled.
Bit 0: Receive Align Frame Event (RAF) (E1 Only). Set every 250μs at the beginning of align frames. Used to
alert the host that Si and Sa bits are available in the TR.RAF and TR.RNAF registers.
221 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IMR4
Register Description:
Register Address:
Interrupt Mask Register 4
1Dh
Bit #
Name
Default
7
RAIS-CI
0
6
RSAO
0
5
RSAZ
0
4
TMF
0
3
TAF
0
2
RMF
0
1
RCMF
0
0
RAF
0
Bit 7: Receive AIS-CI Event (RAIS-CI)
0 = interrupt masked
1 = interrupt enabled
Bit 6: Receive Signaling All-Ones Event (RSAO)
0 = interrupt masked
1 = interrupt enabled
Bit 5: Receive Signaling All-Zeros Event (RSAZ)
0 = interrupt masked
1 = interrupt enabled
Bit 4: Transmit Multiframe Event (TMF)
0 = interrupt masked
1 = interrupt enabled
Bit 3: Transmit Align Frame Event (TAF)
0 = interrupt masked
1 = interrupt enabled
Bit 2: Receive Multiframe Event (RMF)
0 = interrupt masked
1 = interrupt enabled
Bit 1: Receive CRC4 Multiframe Event (RCMF)
0 = interrupt masked
1 = interrupt enabled
Bit 0: Receive Align Frame Event (RAF)
0 = interrupt masked
1 = interrupt enabled
222 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR5
Register Description:
Register Address:
Status Register 5
1Eh
Bit #
Name
Default
7
—
0
6
—
0
5
TESF
0
4
TESEM
0
3
TSLIP
0
2
RESF
0
1
RESEM
0
0
RSLIP
0
Bit 5: Transmit Elastic Store Full Event (TESF). Set when the transmit elastic store buffer fills and a frame is
deleted.
Bit 4: Transmit Elastic Store Empty Event (TESEM). Set when the transmit elastic store buffer empties and a
frame is repeated.
Bit 3: Transmit Elastic Store Slip-Occurrence Event (TSLIP). Set when the transmit elastic store has either
repeated or deleted a frame.
Bit 2: Receive Elastic Store Full Event (RESF). Set when the receive elastic store buffer fills and a frame is
deleted.
Bit 1: Receive Elastic Store Empty Event (RESEM). Set when the receive elastic store buffer empties and a
frame is repeated.
Bit 0: Receive Elastic Store Slip-Occurrence Event (RSLIP). Set when the receive elastic store has either
repeated or deleted a frame.
223 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IMR5
Register Description:
Register Address:
Interrupt Mask Register 5
1Fh
Bit #
Name
Default
7
—
0
6
—
0
5
TESF
0
4
TESEM
0
3
TSLIP
0
2
RESF
0
1
RESEM
0
0
RSLIP
0
Bit 5: Transmit Elastic Store Full Event (TESF)
0 = interrupt masked
1 = interrupt enabled
Bit 4: Transmit Elastic Store Empty Event (TESEM)
0 = interrupt masked
1 = interrupt enabled
Bit 3: Transmit Elastic Store Slip-Occurrence Event (TSLIP)
0 = interrupt masked
1 = interrupt enabled
Bit 2: Receive Elastic Store Full Event (RESF)
0 = interrupt masked
1 = interrupt enabled
Bit 1: Receive Elastic Store Empty Event (RESEM)
0 = interrupt masked
1 = interrupt enabled
Bit 0: Receive Elastic Store Slip-Occurrence Event (RSLIP)
0 = interrupt masked
1 = interrupt enabled
224 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR6, TR.SR7
Register Description:
HDLC #1 Status Register 6
HDLC #2 Status Register 7
20h, 22h
Register Address:
Bit #
Name
Default
7
—
0
6
TMEND
0
5
RPE
0
4
RPS
0
3
RHWM
0
2
RNE
0
1
TLWM
0
0
TNF
0
Bit 6: Transmit Message-End Event (TMEND). Set when the transmit HDLC controller has finished sending a
message. This is a latched bit and is cleared when read.
Bit 5: Receive Packet-End Event (RPE). Set when the HDLC controller detects either the finish of a valid
message (i.e., CRC check complete) or when the controller has experienced a message fault such as a CRC
checking error, or an overrun condition, or an abort has been seen. This is a latched bit and is cleared when read.
Bit 4: Receive Packet-Start Event (RPS). Set when the HDLC controller detects an opening byte. This is a
latched bit and is cleared when read.
Bit 3: Receive FIFO Above High-Watermark Condition (RHWM). Set when the receive 128-byte FIFO fills
beyond the high watermark as defined by the receive high-watermark register (TR.RHWMR).
Bit 2: Receive FIFO Not Empty Condition (RNE). Set when the receive 128-byte FIFO has at least 1 byte
available for a read.
Bit 1: Transmit FIFO Below Low-Watermark Condition (TLWM). Set when the transmit 128-byte FIFO empties
beyond the low watermark as defined by the transmit low-watermark register (TR.TLWMR).
Bit 0: Transmit FIFO Not Full Condition (TNF). Set when the transmit 128-byte FIFO has at least 1 byte
available.
225 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IMR6, TR.IMR7
Register Description:
HDLC # 1 Interrupt Mask Register 6
HDLC # 2 Interrupt Mask Register 7
21h, 23h
Register Address:
Bit #
Name
Default
7
—
0
6
TMEND
0
5
RPE
0
4
RPS
0
3
RHWM
0
2
RNE
0
1
TLWM
0
0
TNF
0
Bit 6: Transmit Message-End Event (TMEND)
0 = interrupt masked
1 = interrupt enabled
Bit 5: Receive Packet-End Event (RPE)
0 = interrupt masked
1 = interrupt enabled
Bit 4: Receive Packet-Start Event (RPS)
0 = interrupt masked
1 = interrupt enabled
Bit 3: Receive FIFO Above High-Watermark Condition (RHWM)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
Bit 2: Receive FIFO Not Empty Condition (RNE)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
Bit 1: Transmit FIFO Below Low-Watermark Condition (TLWM)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
Bit 0: Transmit FIFO Not Full Condition (TNF)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising edge only
226 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.INFO5, TR.INFO6
Register Description:
HDLC #1 Information Register
HDLC #2 Information Register
2Eh, 2Fh
Register Address:
Bit #
Name
Default
7
—
0
6
—
0
5
TEMPTY
0
4
TFULL
0
3
REMPTY
0
2
PS2
0
1
PS1
0
0
PS0
0
Bit 5: Transmit FIFO Empty (TEMPTY). A real-time bit that is set high when the FIFO is empty.
Bit 4: Transmit FIFO Full (TFULL). A real-time bit that is set high when the FIFO is full.
Bit 3: Receive FIFO Empty (REMPTY). A real-time bit that is set high when the receive FIFO is empty.
Bits 0 – 2: Receive Packet Status (PS0 to PS2). These are real-time bits indicating the status as of the last read
of the receive FIFO.
PS2
PS1
PS0
Packet Status
0
0
0
In Progress
0
0
0
1
0
1
1
0
1
0
1
0
Packet OK: Packet ended with correct CRC codeword
CRC Error: A closing flag was detected, preceded by a corrupt CRC
codeword
Abort: Packet ended because an abort signal was detected (seven
or more 1s in a row).
Overrun: HDLC controller terminated reception of packet because
receive FIFO is full.
Register Name:
TR.INFO4
Register Description:
Register Address:
HDLC Event Information Register #4
2Dh
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
H2UDR
0
2
H2OBT
0
1
H1UDR
0
0
H1OBT
0
Bit 3: HDLC #2 Transmit FIFO Underrun Event (H2UDR). Set when the transmit FIFO empties out without
having seen the TMEND bit set. An abort is automatically sent. This bit is latched and is cleared when read.
Bit 2: HDLC #2 Opening Byte Event (H2OBT). Set when the next byte available in the receive FIFO is the first
byte of a message.
Bit 1: HDLC #1 Transmit FIFO Underrun Event (H1UDR). Set when the transmit FIFO empties out without
having seen the TMEND bit set. An abort is automatically sent. This bit is latched and is cleared when read.
Bit 0: HDLC #1 Opening Byte Event (H1OBT). Set when the next byte available in the receive FIFO is the first
byte of a message.
227 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR8
Register Description:
Register Address:
Status Register 8
24h
Bit #
Name
Default
7
—
0
6
—
0
5
BOCC
0
4
RFDLAD
0
3
RFDLF
0
2
TFDLE
0
1
RMTCH
0
0
RBOC
0
Bit 5: BOC Clear Event (BOCC). Set when 30 FDL bits occur without an abort sequence.
Bit 4: RFDL Abort Detect Event (RFDLAD). Set when eight consecutive 1s are received on the FDL.
Bit 3: RFDL Register Full Event (RFDLF). Set when the receive FDL buffer (TR.RFDL) fills to capacity.
Bit 2: TFDL Register Empty Event (TFDLE). Set when the transmit FDL buffer (TR.TFDL) empties.
Bit 1: Receive FDL Match Event (RMTCH). Set whenever the contents of the TR.RFDL register matches
TR.RFDLM1 or TR.RFDLM2.
Bit 0: Receive BOC Detector Change-of-State Event (RBOC). Set whenever the BOC detector sees a change of
state to a valid BOC. The setting of this bit prompts the user to read the TR.RFDL register.
Register Name:
TR.IMR8
Register Description:
Register Address:
Interrupt Mask Register 8
25h
Bit #
Name
Default
7
—
0
6
—
0
5
BOCC
0
4
RFDLAD
0
3
RFDLF
0
2
TFDLE
0
1
RMTCH
0
0
RBOC
0
Bit 5: BOC Clear Event (BOCC)
0 = interrupt masked
1 = interrupt enabled
Bit 4: RFDL Abort Detect Event (RFDLAD)
0 = interrupt masked
1 = interrupt enabled
Bit 3: RFDL Register Full Event (RFDLF)
0 = interrupt masked
1 = interrupt enabled
Bit 2: TFDL Register Empty Event (TFDLE)
0 = interrupt masked
1 = interrupt enabled
Bit 1: Receive FDL Match Event (RMTCH)
0 = interrupt masked
1 = interrupt enabled
Bit 0: Receive BOC Detector Change-of-State Event (RBOC)
0 = interrupt masked
1 = interrupt enabled
228 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SR9
Register Description:
Register Address:
Status Register 9
26h
Bit #
Name
Default
7
—
0
6
BBED
0
5
BBCO
0
4
BEC0
0
3
BRA1
0
2
BRA0
0
1
BRLOS
0
0
BSYNC
0
Bit 6: BERT Bit-Error Detected (BED) Event (BBED). A latched bit that is set when a bit error is detected. The
receive BERT must be in synchronization for it to detect bit errors. Cleared when read.
Bit 5: BERT Bit-Counter Overflow Event (BBCO). A latched bit that is set when the 32-bit BERT bit counter
(BBC) overflows. Cleared when read and is not set again until another overflow occurs.
Bit 4: BERT Error-Counter Overflow (BECO) Event (BECO). A latched bit that is set when the 24-bit BERT error
counter (BEC) overflows. Cleared when read and is not set again until another overflow occurs.
Bit 3: BERT Receive All-Ones Condition (BRA1). A latched bit that is set when 32 consecutive 1s are received.
Bit 2: BERT Receive All-Zeros Condition (BRA0). A latched bit that is set when 32 consecutive 0s are received.
Bit 1: BERT Receive Loss-of-Synchronization Condition (BRLOS). A latched bit that is set whenever the
receive BERT begins searching for a pattern. Once synchronization is achieved, this bit remains set until read. This
Bit 0: BERT in Synchronization Condition (BSYNC). Set when the incoming pattern matches for 32 consecutive
bit positions. Refer to BSYNC in the TR.INFO2 register for a real-time version of this bit. This is a double interrupt
229 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IMR9
Register Description:
Register Address:
Interrupt Mask Register 9
27h
Bit #
Name
Default
7
—
0
6
BBED
0
5
BBCO
0
4
BEC0
0
3
BRA1
0
2
BRA0
0
1
BRLOS
0
0
BSYNC
0
Bit 6: Bit-Error Detected Event (BBED)
0 = interrupt masked
1 = interrupt enabled
Bit 5: BERT Bit-Counter Overflow Event (BBCO)
0 = interrupt masked
1 = interrupt enabled
Bit 4: BERT Error-Counter Overflow Event (BECO)
0 = interrupt masked
1 = interrupt enabled
Bit 3: Receive All-Ones Condition (BRA1)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 2: Receive All-Zeros Condition (BRA0)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 1: Receive Loss-of-Synchronization Condition (BRLOS)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
Bit 0: BERT in Synchronization Condition (BSYNC)
0 = interrupt masked
1 = interrupt enabled—interrupts on rising and falling edges
230 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.PCPR
Register Description:
Register Address:
Per-Channel Pointer Register
28h
Bit #
Name
Default
7
RSAOICS
0
6
RSRCS
0
5
RFCS
0
4
BRCS
0
3
THSCS
0
2
PEICS
0
1
TFCS
0
0
BTCS
0
Bit 7: Receive Signaling All-Ones Insertion Channel Select (RSAOICS)
Bit 6: Receive Signaling Reinsertion Channel Select (RSRCS)
Bit 5: Receive Fractional Channel Select (RFCS)
Bit 4: Bert Receive Channel Select (BRCS)
Bit 3: Transmit Hardware Signaling Channel Select (THSCS)
Bit 2: Payload Error Insert Channel Select (PEICS)
Bit 1: Transmit Fractional Channel Select (TFCS)
Bit 0: Bert Transmit Channel Select (BTCS)
See Section 10.2 for a general overview of per-channel operation. See Section 10.10 for more information on per-
channel idle code generation. See Section 10.6 for more information on per-channel loopback operation.
231 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.PCDR1
Register Description:
Register Address:
Per-Channel Data Register 1
29h
Bit #
7
6
5
4
3
2
1
0
Name
Default
—
CH8
—
CH7
—
CH6
—
CH5
—
CH4
—
CH3
—
CH2
—
CH1
Register Name:
TR.PCDR2
Register Description:
Register Address:
Per-Channel Data Register 2
2Ah
Bit #
Name
Default
7
—
CH16
6
—
CH15
5
—
CH14
4
—
CH13
3
—
CH12
2
—
CH11
1
—
CH10
0
—
CH9
Register Name:
TR.PCDR3
Register Description:
Register Address:
Per-Channel Data Register 3
2Bh
Bit #
Name
Default
7
—
CH24
6
—
CH23
5
—
CH22
4
—
CH21
3
—
CH20
2
—
CH19
1
—
CH18
0
—
CH17
Register Name:
TR.PCDR4
Register Description:
Register Address:
Per-Channel Data Register 4
2Ch
Bit #
Name
Default
7
—
CH32
6
—
CH31
5
—
CH30
4
—
CH29
3
—
CH28
2
—
CH27
1
—
CH26
0
—
CH25
See Section 10.2 for a general overview of per-channel operation. See Section 10.10 for more information on per-
channel idle code generation. See Section 10.6 for more information on per-channel loopback operation.
232 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.INFO7
Register Description:
Register Address:
Information Register 7 (Real-Time, Non-Latched Register)
30h
Bit #
Name
Default
7
CSC5
0
6
CSC4
0
5
CSC3
0
4
CSC2
0
3
CSC0
0
2
FASSA
0
1
CASSA
0
0
CRC4SA
0
Bits 3 – 7: CRC4 Sync Counter Bits (CSC0, CSC2 to CSC4). The CRC4 sync counter increments each time the
8ms CRC4 multiframe search times out. The counter is cleared when the framer has successfully obtained
synchronization at the CRC4 level. The counter can also be cleared by disabling the CRC4 mode (TR.E1RCR1.3 =
0). This counter is useful for determining the amount of time the framer has been searching for synchronization at
the CRC4 level. ITU G.706 suggests that if synchronization at the CRC4 level cannot be obtained within 400ms,
then the search should be abandoned and proper action taken. The CRC4 sync counter rolls over. CSC0 is the
LSB of the 6-bit counter. (Note: The bit next to LSB is not accessible. CSC1 is omitted to allow resolution to
>400ms using 5 bits.) These are read-only, non-latched, real-time bits. It is not necessary to precede the read of
these bits with a write.
Bit 2: FAS Sync Active (FASSA). Set while the synchronizer is searching for alignment at the FAS level. This is a
read-only, non-latched, real-time bit. It is not necessary to precede the read of this bit with a write.
Bit 1: CAS MF Sync Active (CASSA). Set while the synchronizer is searching for the CAS MF alignment word.
This is a read-only, non-latched, real-time bit. It is not necessary to precede the read of this bit with a write.
Bit 0: CRC4 MF Sync Active (CRC4SA). Set while the synchronizer is searching for the CRC4 MF alignment
word. This is a read-only, non-latched, real-time bit. It is not necessary to precede the read of this bit with a write.
Register Name:
Register Description:
TR.H1RC, TR.H2RC
HDLC #1 Receive Control
HDLC #2 Receive Control
31h, 32h
Register Address:
Bit #
Name
Default
7
RHR
0
6
RHMS
0
5
—
0
4
—
0
3
—
0
2
—
0
1
—
0
0
RSFD
0
Bit 7: Receive HDLC Reset (RHR). Resets the receive HDLC controller and flushes the receive FIFO. Must be
cleared and set again for a subsequent reset.
0 = normal operation
1 = reset receive HDLC controller and flush the receive FIFO
Bit 6: Receive HDLC Mapping Select (RHMS)
0 = receive HDLC assigned to channels
1 = receive HDLC assigned to FDL (T1 mode), Sa bits (E1 mode)
Bits 1 – 5: Unused, must be set to 0 or proper operation
Bit 0: Receive SS7 Fill-In Signal Unit Delete (RSFD)
0 = normal operation; all FISUs are stored in the receive FIFO and reported to the host.
1 = When a consecutive FISU having the same BSN the previous FISU is detected, it is deleted without
host intervention.
233 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.E1RCR1
Register Description:
Register Address:
E1 Receive Control Register 1
33h
Bit #
Name
Default
7
RSERC
0
6
RSIGM
0
5
RHDB3
0
4
RG802
0
3
RCRC4
0
2
FRC
0
1
SYNCE
0
0
RESYNC
0
Bit 7: RSERO Control (RSERC)
0 = allow RSERO to output data as received under all conditions
1 = force RSERO to 1 under loss-of-frame alignment conditions
Bit 6: Receive Signaling Mode Select (RSIGM)
0 = CAS signaling mode
1 = CCS signaling mode
Bit 5: Receive HDB3 Enable (RHDB3)
0 = HDB3 disabled
1 = HDB3 enabled
0 = do not force RCHBLK high during bit 1 of time slot 26
1 = force RCHBLK high during bit 1 of time slot 26
Bit 3: Receive CRC4 Enable (RCRC4)
0 = CRC4 disabled
1 = CRC4 enabled
Bit 2: Frame Resync Criteria (FRC)
0 = resync if FAS received in error three consecutive times
1 = resync if FAS or bit 2 of non-FAS is received in error three consecutive times
Bit 1: Sync Enable (SYNCE)
0 = auto resync enabled
1 = auto resync disabled
Bit 0: Resync (RESYNC). When toggled from low to high, a resync is initiated. Must be cleared and set again for a
subsequent resync.
Register Name:
TR.E1RCR2
Register Description:
Register Address:
E1 Receive Control Register 2
34h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
—
0
2
—
0
1
—
0
0
RCLA
0
Bit 0: Receive Carrier-Loss (RCL) Alternate Criteria (RCLA). Defines the criteria for a receive carrier-loss
condition for both the framer and LIU.
0 = RCL declared upon 255 consecutive 0s (125μs)
1 = RCL declared upon 2048 consecutive 0s (1ms)
234 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.E1TCR1
Register Description:
Register Address:
E1 Transmit Control Register 1
35h
Bit #
Name
Default
7
TFPT
0
6
T16S
0
5
TUA1
0
4
TSiS
0
3
TSA1
0
2
THDB3
0
1
TG802
0
0
TCRC4
0
Bit 7: Transmit Time Slot 0 Pass-Through (TFPT)
0 = FAS bits/Sa bits/remote alarm sourced internally from the TR.TAF and TR.TNAF registers
1 = FAS bits/Sa bits/remote alarm sourced from TSERI
Bit 6: Transmit Time Slot 16 Data Select (T16S)
0 = time slot 16 determined by the TR.SSIEx registers and the THSCS function in the TR.PCPR register
1 = source time slot 16 from TR.TS1 to TR.TS16 registers
Bit 5: Transmit Unframed All Ones (TUA1)
0 = transmit data normally
1 = transmit an unframed all-ones code at TPOSO and TNEGO
Bit 4: Transmit International Bit Select (TSiS)
0 = sample Si bits at TSERI pin
1 = source Si bits from TR.TAF and TR.TNAF registers (in this mode, TR.E1TCR1.7 must be set to 0)
Bit 3: Transmit Signaling All Ones (TSA1)
0 = normal operation
1 = force time slot 16 in every frame to all ones
Bit 2: Transmit HDB3 Enable (THDB3)
0 = HDB3 disabled
1 = HDB3 enabled
0 = do not force TCHBLK high during bit 1 of time slot 26
1 = force TCHBLK high during bit 1 of time slot 26
Bit 0: Transmit CRC4 Enable (TCRC4)
0 = CRC4 disabled
1 = CRC4 enabled
235 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.E1TCR2
Register Description:
Register Address:
E1 Transmit Control Register 2
36h
Bit #
Name
Default
7
-
0
6
-
0
5
-
0
4
-
0
3
-
0
2
AEBE
0
1
AAIS
0
0
ARA
0
Bit 2: Automatic E-Bit Enable (AEBE)
0 = E-bits not automatically set in the transmit direction
1 = E-bits automatically set in the transmit direction
Bit 1: Automatic AIS Generation (AAIS)
0 = disabled
1 = enabled
Bit 0: Automatic Remote Alarm Generation (ARA)
0 = disabled
1 = enabled
Register Name:
TR.BOCC
Register Description:
Register Address:
BOC Control Register
37h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
RBOCE
0
3
RBR
0
2
RBF1
0
1
RBF0
0
0
SBOC
0
Bit 4: Receive BOC Enable (RBOCE). Enables the receive BOC function. The TR.RFDL register reports the
received BOC code and two information bits when this bit is set.
0 = receive BOC function disabled
1 = receive BOC function enabled; the TR.RFDL register reports BOC messages and information
Bit 3: Receive BOC Reset (RBR). A 0-to-1 transition resets the BOC circuitry. Must be cleared and set again for a
subsequent reset.
Bits 1 – 2: Receive BOC Filter Bits (RBF0, RBF1). The BOC filter sets the number of consecutive patterns that
must be received without error prior to an indication of a valid message.
Consecutive BOC Codes for
Valid Sequence Identification
RBF1
RBF0
0
0
1
1
0
1
0
1
None
3
5
7
Bit 0: Send BOC (SBOC). Set = 1 to transmit the BOC code placed in bits 0 to 5 of the TR.TFDL register.
236 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
TR.RSINFO1, TR.RSINFO2, TR.RSINFO3, TR.RSINFO4
Register Name:
Register Description:
Register Address:
Receive Signaling Change-of-State Information
38h, 39h, 3Ah, 3Bh
(MSB)
CH8
(LSB)
CH1
CH7
CH6
CH5
CH4
CH3
CH2
RSINFO1
RSINFO2
RSINFO3
RSINFO4
CH16
CH24
CH15
CH23
CH14
CH22
CH30
CH13
CH21
CH29
CH12
CH20
CH28
CH11
CH19
CH27
CH10
CH18
CH26
CH9
CH17
CH25
When a channel’s signaling data changes state, the respective bit in registers TR.RSINFO1–4 is set. An interrupt is
generated if the channel was also enabled as an interrupt source by setting the appropriate bit in TR.RSCSE1–4.
The bit remains set until read.
Register Name:
Register Description:
Register Address:
TR.RSCSE1, TR.RSCSE2, TR.RSCSE3, TR.RSCSE4
Receive Signaling Change-of-State Interrupt Enable
3Ch, 3Dh, 3Eh, 3Fh
(MSB)
CH8
(LSB)
CH1
CH7
CH6
CH5
CH4
CH3
CH2
RSCSE1
RSCSE2
RSCSE3
RSCSE4
CH16
CH24
CH15
CH23
CH14
CH22
CH30
CH13
CH21
CH29
CH12
CH20
CH28
CH11
CH19
CH27
CH10
CH18
CH26
CH9
CH17
CH25
Setting any of the CH1–CH30 bits in the TR.RSCSE1– TR.RSCSE4 registers causes an interrupt when that
channel’s signaling data changes state.
237 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.SIGCR
Register Description:
Register Address:
Signaling Control Register
40h
Bit #
Name
Default
7
GRSRE
0
6
—
0
5
—
0
4
RFE
0
3
RFF
0
2
RCCS
0
1
TCCS
0
0
FRSAO
0
Bit 7: Global Receive Signaling Reinsertion Enable (GRSRE). This bit allows the user to reinsert all signaling
channels without programming all channels through the per-channel function.
0 = do not reinsert all signaling
1 = reinsert all signaling
0 = no freezing of receive signaling data occurs
1 = allow freezing of receive signaling data at RSIG (and RSERO if receive signaling reinsertion is
enabled)
Bit 3: Receive Force Freeze (RFF). Freezes receive-side signaling at RSIG (and RSERO if receive signaling
0 = do not force a freeze event
1 = force a freeze event
Bit 2: Receive Time Slot Control for CAS Signaling (RCCS). Controls the order that signaling is placed into the
receive signaling registers. This bit should be set = 0 in T1 mode.
0 = signaling data is CAS format
1 = signaling data is CCS format
Bit 1: Transmit Time Slot Control for CAS Signaling (TCCS). Controls the order that signaling is transmitted
from the transmit signaling registers. This bit should be set = 0 in T1 mode.
0 = signaling data is CAS format
1 = signaling data is CCS format
Bit 0: Force Receive Signaling All Ones (FRSAO). In T1 mode, this bit forces all signaling data at the RSIG and
RSERO pin to all ones. This bit has no effect in E1 mode.
0 = normal signaling data at RSIG and RSERO
1 = force signaling data at RSIG and RSERO to all ones
238 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.ERCNT
Register Description:
Register Address:
Error-Counter Configuration Register
41h
Bit #
Name
Default
7
—
0
6
MECU
0
5
ECUS
0
4
EAMS
0
3
VCRFS
0
2
FSBE
0
1
MOSCRF
0
0
LCVCRF
0
Bit 6: Manual Error-Counter Update (MECU). When enabled by TR.ERCNT.4, the changing of this bit from a 0 to
a 1 allows the next clock cycle to load the error-counter registers with the latest counts and reset the counters. The
user must wait a minimum of 1.5 RCLKO clock periods before reading the error count registers to allow for proper
update.
Bit 5: Error-Counter Update Select (ECUS)
T1 Mode:
0 = update error counters once a second
1 = update error counters every 42ms (333 frames)
E1 Mode:
0 = update error counters once a second
1 = update error counters every 62.5ms (500 frames)
Bit 4: Error-Accumulation Mode Select (EAMS)
0 = TR.ERCNT.5 determines accumulation time
1 = TR.ERCNT.6 determines accumulation time
Bit 3: E1 Line-Code Violation Count Register Function Select (VCRFS)
0 = count bipolar violations (BPVs)
1 = count code violations (CVs)
Bit 2: PCVCR Fs-Bit Error-Report Enable (FSBE)
0 = do not report bit errors in Fs-bit position; only Ft-bit position
1 = report bit errors in Fs-bit position as well as Ft-bit position
Bit 1: Multiframe Out-of-Sync Count Register Function Select (MOSCRF)
0 = count errors in the framing bit position
1 = count the number of multiframes out-of-sync
Bit 0: T1 Line-Code Violation Count Register Function Select (LCVCRF)
0 = do not count excessive 0s
1 = count excessive 0s
239 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.LCVCR1
Register Description:
Register Address:
Line-Code Violation Count Register 1
42h
Bit #
Name
Default
7
LCVC15
0
6
LCVC14
0
5
LCVC13
0
4
LCVC12
0
3
LCVC11
0
2
LCVC10
0
1
LCVC9
0
0
LCVC8
0
Bits 0 – 7: Line-Code Violation Counter Bits 8 to 15 (LCVC8 to LCVC15). LCVC15 is the MSB of the 16-bit
code violation count.
Register Name:
TR.LCVCR2
Register Description:
Register Address:
Line-Code Violation Count Register 2
43h
Bit #
Name
Default
7
6
5
4
3
2
LCVC3
0
1
LCVC2
0
0
LCVC7
0
LCVC6
0
LCVC5
0
LCVC4
0
LCVC1
0
LCVC0
0
Bits 0 – 7: Line-Code Violation Counter Bits 0 to 7 (LCVC0 to LCVC7). LCVC0 is the LSB of the 16-bit code
violation count.
Register Name:
TR.PCVCR1
Register Description:
Register Address:
Path Code Violation Count Register 1
44h
Bit #
Name
Default
7
PCVC15
0
6
PCVC14
0
5
4
3
2
1
0
PCVC13
0
PCVC12
0
PCVC11
0
PCVC10
0
PCVC9
0
PCVC8
0
Bits 0 – 7: Path Code Violation Counter Bits 8 to 15 (PCVC8 to PCVC15). PCVC15 is the MSB of the 16-bit
path code violation count.
Register Name:
TR.PCVCR2
Register Description:
Register Address:
Path Code Violation Count Register 2
45h
Bit #
Name
Default
7
PCVC7
0
6
PCVC6
0
5
PCVC5
0
4
PCVC4
0
3
PCVC3
0
2
PCVC2
0
1
PCVC1
0
0
PCVC0
0
Bits 0 – 7: Path Code Violation Counter Bits 0 to 7 (PCVC0 to PCVC7). PCVC0 is the LSB of the 16-bit path
code violation count.
240 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.FOSCR1
Register Description:
Register Address:
Frames Out-of-Sync Count Register 1
46h
Bit #
Name
Default
7
FOS15
0
6
FOS14
0
5
FOS13
0
4
FOS12
0
3
FOS11
0
2
FOS10
0
1
FOS9
0
0
FOS8
0
Bits 0 – 7: Frames Out-of-Sync Counter Bits 8 to 15 (FOS8 to FOS15). FOS15 is the MSB of the 16-bit frames
out-of-sync count.
Register Name:
TR.FOSCR2
Register Description:
Register Address:
Frames Out-of-Sync Count Register 2
47h
Bit #
Name
Default
7
FOS7
0
6
FOS6
0
5
FOS5
0
4
FOS4
0
3
FOS3
0
2
FOS2
0
1
FOS1
0
0
FOS0
0
Bits 0 – 7: Frames Out-of-Sync Counter Bits 0 to 7 (FOS0 to FOS7). FOS0 is the LSB of the 16-bit frames out-
of-sync count.
Register Name:
TR.EBCR1
Register Description:
Register Address:
E-Bit Count Register 1
48h
Bit #
Name
Default
7
EB15
0
6
EB14
0
5
EB13
0
4
EB12
0
3
EB11
0
2
EB10
0
1
EB9
0
0
EB8
0
Bits 0 – 7: E-Bit Counter Bits 8 to 15 (EB8 to EB15). EB15 is the MSB of the 16-bit E-bit count.
Register Name:
TR.EBCR2
Register Description:
Register Address:
E-Bit Count Register 2
49h
Bit #
Name
Default
7
EB7
0
6
EB6
0
5
EB5
0
4
EB4
0
3
EB3
0
2
EB2
0
1
EB1
0
0
EB0
0
Bits 0 – 7: E-Bit Counter Bits 0 to 7 (EB0 to EB7). EB0 is the LSB of the 16-bit E-bit count.
241 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.LBCR
Register Description:
Register Address:
Loopback Control Register
4Ah
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
LIUC
0
3
LLB
0
2
RLB
0
1
PLB
0
0
FLB
0
Bit 4: Line Interface Unit Mux Control (LIUC). This is a software version of the LIUC pin. When the LIUC pin is
connected high, the LIUC bit has control. When the LIUC pin is connected low, the framer and LIU are separated
and the LIUC bit has no effect.
0 = LIU internally connected to framer.
1 = LIU disconnected from framer. Use TPOSI/TNEGI/TDCLKI/RPOSI/RNEGI/RDCLKI pins
LIUC Pin
LIUC Bit
Condition
0
0
1
0
1
0
LIU and framer separated
LIU and framer separated
LIU and framer connected
LIU and framer separated
1
1
Bit 3: Local Loopback (LLB). When this bit is set to 1, data continues to be transmitted as normal through the
transmit side of the transceiver. Data being received at RTIP and RRING are replaced with the data being
transmitted. Data in this loopback passes through the jitter attenuator. See Figure 6-3 for more details.
Bit 2: Remote Loopback (RLB). When this bit is set to 1, data input by the RPOSI and RNEGI pins is transmitted
back to the TPOSO and TNEGO pins. Data continues to pass through the receive-side framer of the transceiver as
it would normally. Data from the transmit-side formatter is ignored. See Figure 6-2 for more details.
Bit 1: Payload Loopback (PLB). When set to 1, payload loopback is enabled and the following occurs:
1) Data is transmitted from the TPOSO and TNEGO pins synchronous with RCLKO instead of TCLKT.
2) All the receive side signals continue to operate normally.
3) Data at the TSERI, TDATA, and TSIG pins is ignored.
T1 Mode: Normally, this loopback is only enabled when ESF framing is being performed but can also be enabled in
D4 framing applications. The transceiver loops the 192 bits of payload data (with BPVs corrected) from the receive
section back to the transmit section. The FPS framing pattern, CRC6 calculation, and the FDL bits are not looped
back; they are reinserted by the transceiver.
E1 Mode: The transceiver loops the 248 bits of payload data (with BPVs corrected) from the receive section back
to the transmit section. The transmit section modifies the payload as if it was input at TSERI. The FAS word; Si,
Sa, and E bits; and CRC4 are not looped back; they are reinserted by the transceiver.
Bit 0: Framer Loopback (FLB). When this bit is set to 1, the transceiver loops data from the transmit side back to
the receive side. When FLB is enabled, the following occurs:
1) T1 Mode: An unframed all-ones code is transmitted at TPOSO and TNEGO.
E1 Mode: Normal data is transmitted at TPOSO and TNEGO.
2) Data at RPOSI and RNEGI is ignored.
3) All receive-side signals take on timing synchronous with TCLKT instead of RDCLKI.
Please note that it is not acceptable to have RCLKO connected to TCLKT during this loopback because this
causes an unstable condition.
242 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.PCLR1
Register Description:
Register Address:
Per-Channel Loopback Enable Register 1
4Bh
Bit #
Name
Default
7
CH8
0
6
CH7
0
5
CH6
0
4
CH5
0
3
CH4
0
2
CH3
0
1
CH2
0
0
CH1
0
Bits 0 – 7: Per-Channel Loopback Enable for Channels 1 to 8 (CH1 to CH8)
0 = loopback disabled
1 = enable loopback; source data from the corresponding receive channel
Register Name:
TR.PCLR2
Register Description:
Register Address:
Per-Channel Loopback Enable Register 2
4Ch
Bit #
Name
Default
7
CH16
0
6
CH15
0
5
CH14
0
4
CH13
0
3
CH12
0
2
CH11
0
1
CH10
0
0
CH9
0
Bits 0 – 7: Per-Channel Loopback Enable for Channels 9 to 16 (CH9 to CH16)
0 = loopback disabled
1 = enable loopback; source data from the corresponding receive channel
Register Name:
TR.PCLR3
Register Description:
Register Address:
Per-Channel Loopback Enable Register 3
4Dh
Bit #
Name
Default
7
CH24
0
6
CH23
0
5
CH22
0
4
CH21
0
3
CH20
0
2
CH19
0
1
CH18
0
0
CH17
0
Bits 0 – 7: Per-Channel Loopback Enable for Channels 17 to 24 (CH17 to CH24)
0 = loopback disabled
1 = enable loopback; source data from the corresponding receive channel
Register Name:
TR.PCLR4
Register Description:
Register Address:
Per-Channel Loopback Enable Register 4
4Eh
Bit #
Name
Default
7
CH32
0
6
CH31
0
5
CH30
0
4
CH29
0
3
CH28
0
2
CH27
0
1
CH26
0
0
CH25
0
Bits 0 – 7: Per-Channel Loopback Enable for Channels 25 to 32 (CH25 to CH32)
0 = loopback disabled
1 = enable loopback; source data from the corresponding receive channel
243 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.ESCR
Register Description:
Register Address:
Elastic Store Control Register
4Fh
Bit #
Name
Default
7
TESALGN
0
6
TESR
0
5
TESMDM
0
4
TESE
0
3
RESALGN
0
2
RESR
0
1
RESMDM
0
0
RESE
0
Bit 7: Transmit Elastic Store Align (TESALGN). Setting this bit from a 0 to a 1 forces the transmit elastic store’s
write/read pointers to a minimum separation of half a frame. No action is taken if the pointer separation is already
greater or equal to half a frame. If pointer separation is less than half a frame, the command is executed and the
data is disrupted. It should be toggled after TSYSCLK has been applied and is stable. It must be cleared and set
Bit 6: Transmit Elastic Store Reset (TESR). Setting this bit from a 0 to a 1 forces the read and write pointers into
opposite frames, maximizing the delay through the transmit elastic store. Transmit data is lost during the reset. It
should be toggled after TSYSCLK has been applied and is stable. See Section 10.12.3 for details. Do not leave
this bit set HIGH.
0 = elastic stores operate at full two-frame depth
1 = elastic stores operate at 32-bit depth
Bit 4: Transmit Elastic Store Enable (TESE)
0 = elastic store is bypassed
1 = elastic store is enabled
Bit 3: Receive Elastic Store Align (RESALGN). Setting this bit from a 0 to a 1 forces the receive elastic store’s
write/read pointers to a minimum separation of half a frame. No action is taken if the pointer separation is already
greater or equal to half a frame. If pointer separation is less than half a frame, the command is executed and the
data is disrupted. It should be toggled after RSYSCLK has been applied and is stable. Must be cleared and set
Bit 2: Receive Elastic Store Reset (RESR). Setting this bit from a 0 to a 1 forces the read and write pointers into
opposite frames, maximizing the delay through the receive elastic store. It should be toggled after RSYSCLK has
0 = elastic stores operate at full two-frame depth
1 = elastic stores operate at 32-bit depth
Bit 0: Receive Elastic Store Enable (RESE)
0 = elastic store is bypassed
1 = elastic store is enabled
244 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TS1 to TR.TS16
Register Description:
Register Address:
Transmit Signaling Registers (E1 Mode, CAS Format)
50h to 5Fh
(MSB)
(LSB)
0
0
0
0
X
Y
X
X
TS1
TS2
TS3
TS4
TS5
TS6
CH2-A
CH4-A
CH6-A
CH8-A
CH2-B
CH4-B
CH6-B
CH8-B
CH2-C
CH4-C
CH6-C
CH8-C
CH2-D
CH4-D
CH6-D
CH8-D
CH1-A
CH3-A
CH5-A
CH7-A
CH1-B
CH3-B
CH5-B
CH7-B
CH9-B
CH1-C
CH3-C
CH5-C
CH7-C
CH9-C
CH1-D
CH3-D
CH5-D
CH7-D
CH9-D
CH10-A CH10-B CH10-C CH10-D CH9-A
CH12-A CH12-B CH12-C CH12-D CH11-A CH11-B CH11-C CH11-D TS7
CH14-A CH14-B CH14-C CH14-D CH13-A CH13-B CH13-C CH13-D TS8
CH16-A CH16-B CH16-C CH16-D CH15-A CH15-B CH15-C CH15-D TS9
CH18-A CH18-B CH18-C CH18-D CH17-A CH17-B CH17-C CH17-D TS10
CH20-A CH20-B CH20-C CH20-D CH19-A CH19-B CH19-C CH19-D TS11
CH22-A CH22-B CH22-C CH22-D CH21-A CH21-B CH21-C CH21-D TS12
CH24-A CH24-B CH24-C CH24-D CH23-A CH23-B CH23-C CH23-D TS13
CH26-A CH26-B CH26-C CH26-D CH25-A CH25-B CH25-C CH25-D TS14
CH28-A CH28-B CH28-C CH28-D CH27-A CH27-B CH27-C CH27-D TS15
CH30-A CH30-B CH30-C CH30-D CH29-A CH29-B CH29-C CH29-D TS16
245 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TS1 to TR.TS16
Register Description:
Register Address:
Transmit Signaling Registers (E1 Mode, CCS Format)
50h to 5Fh
(MSB)
(LSB)
1
9
2
10
18
26
34
42
50
58
66
74
82
90
98
106
114
122
3
11
19
27
35
43
51
59
67
75
83
91
99
107
115
123
4
12
20
28
36
44
52
60
68
76
84
92
100
108
116
124
5
13
21
29
37
45
53
61
69
77
85
93
101
109
117
125
6
14
22
30
38
46
54
62
70
78
86
94
102
110
118
126
7
15
23
31
39
47
55
63
71
79
87
95
103
111
119
127
8
16
24
32
40
48
56
64
72
80
88
96
104
112
120
128
TS1
TS2
TS3
TS4
TS5
TS6
TS7
TS8
17
25
33
41
49
57
65
73
81
89
97
105
113
121
TS9
TS10
TS11
TS12
TS13
TS14
TS15
TS16
246 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TS1 to TR.TS12
Register Description:
Register Address:
Transmit Signaling Registers (T1 Mode, ESF Format)
50h to 5Bh
(MSB)
(LSB)
CH2-A
CH4-A
CH6-A
CH8-A
CH2-B
CH4-B
CH6-B
CH8-B
CH2-C
CH4-C
CH6-C
CH8-C
CH2-D
CH4-D
CH6-D
CH8-D
CH1-A
CH3-A
CH5-A
CH7-A
CH1-B
CH3-B
CH5-B
CH7-B
CH9-B
CH1-C
CH3-C
CH5-C
CH7-C
CH9-C
CH1-D
CH3-D
CH5-D
CH7-D
CH9-D
TS1
TS2
TS3
TS4
TS5
CH10-A CH10-B CH10-C CH10-D CH9-A
CH12-A CH12-B CH12-C CH12-D CH11-A CH11-B CH11-C CH11-D TS6
CH14-A CH14-B CH14-C CH14-D CH13-A CH13-B CH13-C CH13-D TS7
CH16-A CH16-B CH16-C CH16-D CH15-A CH15-B CH15-C CH15-D TS8
CH18-A CH18-B CH18-C CH18-D CH17-A CH17-B CH17-C CH17-D TS9
CH20-A CH20-B CH20-C CH20-D CH19-A CH19-B CH19-C CH19-D TS10
CH22-A CH22-B CH22-C CH22-D CH21-A CH21-B CH21-C CH21-D TS11
CH24-A CH24-B CH24-C CH24-D CH23-A CH23-B CH23-C CH23-D TS12
247 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TS1 to TR.TS12
Register Description:
Register Address:
Transmit Signaling Registers (T1 Mode, D4 Format)
50h to 5Bh
(MSB)
CH2-A
(LSB)
CH1-B
CH2-B
CH1-A
CH1-B
TS1
TS2
TS3
TS4
TS5
TS6
TS7
TS8
TS9
TS10
TS11
TS12
CH2-A
CH2-B
CH1-A
CH4-A
CH6-A
CH8-A
CH4-B
CH6-B
CH8-B
CH3-A
CH5-A
CH7-A
CH9-A
CH11-A
CH13-A
CH15-A
CH17-A
CH19-A
CH21-A
CH23-A
CH3-B
CH5-B
CH7-B
CH9-B
CH11-B
CH13-B
CH15-B
CH17-B
CH19-B
CH21-B
CH23-B
CH4-A
CH6-A
CH8-A
CH4-B
CH6-B
CH8-B
CH3-A
CH5-A
CH7-A
CH9-A
CH11-A
CH13-A
CH15-A
CH17-A
CH19-A
CH21-A
CH23-A
CH3-B
CH5-B
CH7-B
CH9-B
CH11-B
CH13-B
CH15-B
CH17-B
CH19-B
CH21-B
CH23-B
CH10-A
CH12-A
CH14-A
CH16-A
CH18-A
CH20-A
CH22-A
CH24-A
CH10-B
CH12-B
CH14-B
CH16-B
CH18-B
CH20-B
CH22-B
CH24-B
CH10-A
CH12-A
CH14-A
CH16-A
CH18-A
CH20-A
CH22-A
CH24-A
CH10-B
CH12-B
CH14-B
CH16-B
CH18-B
CH20-B
CH22-B
CH24-B
Note: In D4 format, TR.TS1– TR.TS12 contain signaling data for two frames. Bold type indicates data for second
frame.
248 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RS1 to TR.RS12
Register Description:
Register Address:
Receive Signaling Registers (T1 Mode, ESF Format)
60h to 6Bh
(MSB)
(LSB)
CH2-A
CH4-A
CH6-A
CH8-A
CH2-B
CH4-B
CH6-B
CH8-B
CH2-C
CH4-C
CH6-C
CH8-C
CH2-D
CH4-D
CH6-D
CH8-D
CH1-A
CH3-A
CH5-A
CH7-A
CH1-B
CH3-B
CH5-B
CH7-B
CH9-B
CH1-C
CH3-C
CH5-C
CH7-C
CH9-C
CH1-D
CH3-D
CH5-D
CH7-D
CH9-D
RS1
RS2
RS3
RS4
RS5
CH10-A CH10-B CH10-C CH10-D CH9-A
CH12-A CH12-B CH12-C CH12-D CH11-A CH11-B CH11-C CH11-D RS6
CH14-A CH14-B CH14-C CH14-D CH13-A CH13-B CH13-C CH13-D RS7
CH16-A CH16-B CH16-C CH16-D CH15-A CH15-B CH15-C CH15-D RS8
CH18-A CH18-B CH18-C CH18-D CH17-A CH17-B CH17-C CH17-D RS9
CH20-A CH20-B CH20-C CH20-D CH19-A CH19-B CH19-C CH19-D RS10
CH22-A CH22-B CH22-C CH22-D CH21-A CH21-B CH21-C CH21-D RS11
CH24-A CH24-B CH24-C CH24-D CH23-A CH23-B CH23-C CH23-D RS12
Register Name:
TR.RS1 to TR.RS12
Register Description:
Register Address:
Receive Signaling Registers (T1 Mode, D4 Format)
60h to 6Bh
(MSB)
(LSB)
CH1-B
CH3-B
CH5-B
CH7-B
CH2-A
CH4-A
CH6-A
CH8-A
CH2-B
CH4-B
CH6-B
CH8-B
CH1-A
CH3-A
CH5-A
CH7-A
CH1-B
CH3-B
CH5-B
CH7-B
RS1
RS2
RS3
RS4
RS5
RS6
RS7
RS8
RS9
RS10
RS11
RS12
CH2-A
CH4-A
CH6-A
CH8-A
CH2-B
CH4-B
CH6-B
CH8-B
CH1-A
CH3-A
CH5-A
CH7-A
CH10-A CH10-B
CH12-A CH12-B
CH14-A CH14-B
CH16-A CH16-B
CH18-A CH18-B
CH20-A CH20-B
CH22-A CH22-B
CH24-A CH24-B
CH9-A
CH9-B
CH10-A
CH12-A
CH14-A
CH16-A
CH18-A
CH20-A
CH22-A
CH24-A
CH10-B
CH12-B
CH14-B
CH16-B
CH18-B
CH20-B
CH22-B
CH24-B
CH9-A
CH9-B
CH11-A
CH13-A
CH15-A
CH17-A
CH19-A
CH21-A
CH23-A
CH11-B
CH13-B
CH15-B
CH17-B
CH19-B
CH21-B
CH23-B
CH11-A
CH13-A
CH15-A
CH17-A
CH19-A
CH21-A
CH23-A
CH11-B
CH13-B
CH15-B
CH17-B
CH19-B
CH21-B
CH23-B
Note: In D4 format, TR.TS1– TR.TS12 contain signaling data for two frames. Bold type indicates data for second
frame.
249 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RS1 to TR.RS16
Register Description:
Register Address:
Receive Signaling Registers (E1 Mode, CAS Format)
60h to 6Fh
(MSB)
(LSB)
0
0
0
0
X
Y
X
X
RS1
RS2
RS3
RS4
RS5
RS6
CH2-A
CH4-A
CH6-A
CH8-A
CH2-B
CH4-B
CH6-B
CH8-B
CH2-C
CH4-C
CH6-C
CH8-C
CH2-D
CH4-D
CH6-D
CH8-D
CH1-A
CH3-A
CH5-A
CH7-A
CH1-B
CH3-B
CH5-B
CH7-B
CH9-B
CH1-C
CH3-C
CH5-C
CH7-C
CH9-C
CH1-D
CH3-D
CH5-D
CH7-D
CH9-D
CH10-A CH10-B CH10-C CH10-D CH9-A
CH12-A CH12-B CH12-C CH12-D CH11-A CH11-B CH11-C CH11-D RS7
CH14-A CH14-B CH14-C CH14-D CH13-A CH13-B CH13-C CH13-D RS8
CH16-A CH16-B CH16-C CH16-D CH15-A CH15-B CH15-C CH15-D RS9
CH18-A CH18-B CH18-C CH18-D CH17-A CH17-B CH17-C CH17-D RS10
CH20-A CH20-B CH20-C CH20-D CH19-A CH19-B CH19-C CH19-D RS11
CH22-A CH22-B CH22-C CH22-D CH21-A CH21-B CH21-C CH21-D RS12
CH24-A CH24-B CH24-C CH24-D CH23-A CH23-B CH23-C CH23-D RS13
CH26-A CH26-B CH26-C CH26-D CH25-A CH25-B CH25-C CH25-D RS14
CH28-A CH28-B CH28-C CH28-D CH27-A CH27-B CH27-C CH27-D RS15
CH30-A CH30-B CH30-C CH30-D CH29-A CH29-B CH29-C CH29-D RS16
Register Name:
TR.RS1 to TR.RS16
Register Description:
Register Address:
Receive Signaling Registers (E1 Mode, CCS Format)
60h to 6Fh
(MSB)
(LSB)
1
9
2
10
18
26
34
42
50
58
66
74
82
90
98
106
114
122
3
11
19
27
35
43
51
59
67
75
83
91
99
107
115
123
4
12
20
28
36
44
52
60
68
76
84
92
100
108
116
124
5
13
21
29
37
45
53
61
69
77
85
93
101
109
117
125
6
14
22
30
38
46
54
62
70
78
86
94
102
110
118
126
7
15
23
31
39
47
55
63
71
79
87
95
103
111
119
127
8
16
24
32
40
48
56
64
72
80
88
96
104
112
120
128
RS1
RS2
RS3
RS4
RS5
RS6
RS7
RS8
17
25
33
41
49
57
65
73
81
89
97
105
113
121
RS9
RS10
RS11
RS12
RS13
RS14
RS15
RS16
250 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.CCR1
Register Description:
Register Address:
Common Control Register 1
70h
Bit #
Name
Default
7
MCLKS
0
6
CRC4R
0
5
SIE
0
4
ODM
0
3
DICAI
0
2
TCSS1
0
1
TCSS0
0
0
RLOSF
0
Bit 7: MCLK Source (MCLKS). Selects the source of MCLK
0 = MCLK is source from the MCLK pin
1 = MCLK is source from the TSYSCLK pin
Bit 6: CRC-4 Recalculate (CRC4R)
0 = transmit CRC-4 generation and insertion operates in normal mode
1 = transmit CRC-4 generation operates according to G.706 intermediate path recalculation method
Bit 5: Signaling Integration Enable (SIE)
0 = signaling changes of state reported on any change in selected channels
1 = signaling must be stable for three multiframes in order for a change of state to be reported
Bit 4: Output Data Mode (ODM)
0 = pulses at TPOSO and TNEGO are one full TCLKO period wide
1 = pulses at TPOSO and TNEGO are one-half TCLKO period wide
Bit 3: Disable Idle Code Auto Increment (DICAI). Selects/deselects the auto-increment feature for the transmit
0 = addresses in TR.IAAR register automatically increment on every read/write operation to the TR.PCICR
register
1 = addresses in TR.IAAR register do not automatically increment
Bit 2: Transmit Clock Source Select Bit 0 (TCSS1)
TCSS1
TCSS0
Transmit Clock Source
0
0
The TCLKT pin is always the source of transmit clock.
Switch to the clock present at RCLKO when the signal at the TCLKT pin
fails to transition after 1 channel time.
Use the scaled signal present at MCLK as the transmit clock. The
TCLKT pin is ignored.
Use the signal present at RCLKO as the transmit clock. The TCLKT pin
is ignored.
0
1
1
1
0
1
Bit 1: Transmit Clock Source Select Bit 0 (TCSS0)
Bit 0: Function of the RLOS/LOTC Output (RLOSF)
0 = receive loss of sync (RLOS)
1 = loss-of-transmit clock (LOTC)
251 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.CCR2
Register Description:
Register Address:
Common Control Register 2
71h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
—
0
2
BPCS1
0
1
BPCS0
0
0
BPEN
0
Bits 1 – 2: Backplane Clock Selects (BPCS0, BPCS1)
BPCS1
BPCS0
BPCLK Frequency (MHz)
0
0
1
1
0
1
0
1
16.384
8.192
4.096
2.048
Bit 0: Backplane Clock Enable (BPEN)
0 = disable BPCLK pin (pin held at logic 0)
1 = enable BPCLK pin
Register Name:
TR.CCR3
Register Description:
Register Address:
Common Control Register 3
72h
Bit #
Name
Default
7
6
5
—
0
4
—
0
3
TDATFMT
0
2
1
0
TMSS INTDIS
TGPCKEN
0
RDATFMT
0
RGPCKEN
0
0
0
Bit 7: Transmit Multiframe Sync Source (TMSS). Should be set = 0 only when transmit hardware signaling is
enabled.
0 = elastic store is source of multiframe sync
1 = framer or TSYNC pin is source of multiframe sync
Bit 6: Interrupt Disable (INTDIS). This bit is convenient for disabling interrupts without altering the various
interrupt mask register settings.
0 = interrupts are enabled according to the various mask register settings
1 = interrupts are disabled regardless of the mask register settings
Bit 3: Transmit Channel-Data Format (TDATFMT)
0 = 64kbps (data contained in all 8 bits)
1 = 56kbps (data contained in seven out of the 8 bits)
Bit 2: Transmit Gapped-Clock Enable (TGPCKEN)
0 = TCHCLK functions normally
1 = enable gapped bit-clock output on TCHCLK
Bit 1: Receive Channel-Data Format (RDATFMT)
0 = 64kbps (data contained in all 8 bits)
1 = 56kbps (data contained in seven out of the 8 bits)
Bit 0: Receive Gapped-Clock Enable (RGPCKEN)
0 = RCHCLK functions normally
1 = enable gapped bit-clock output on RCHCLK
252 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.CCR4
Register Description:
Register Address:
Common Control Register 4
73h
Bit #
Name
Default
7
RLT3
0
6
RLT2
0
5
RLT1
0
4
RLT0
0
3
—
0
2
—
0
1
—
0
0
—
0
Bits 4 – 7: Receive Level Threshold Bits (RLT0 to RLT3)
RLT3
RLT2
RLT1
RLT0
Receive Level (dB)
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Greater than -2.5
-2.5
-5.0
-7.5
-10.0
-12.5
-15.0
-17.5
-20.0
-22.5
-25.0
-27.5
-30.0
-32.5
-35.0
Less than -37.5
Register Name:
TR.TDS0SEL
Register Description:
Register Address:
Transmit Channel Monitor Select
74h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
TCM4
0
3
TCM3
0
2
TCM2
0
1
TCM1
0
0
TCM0
0
Bits 0 – 4: Transmit Channel Monitor Bits (TCM0 to TCM4). TCM0 is the LSB of a 5-bit channel select that
determines which transmit channel data appear in the TR.TDS0M register.
253 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TDS0M
Register Description:
Register Address:
Transmit DS0 Monitor Register
75h
Bit #
Name
Default
7
B1
0
6
B2
0
5
B3
0
4
B4
0
3
B5
0
2
B6
0
1
B7
0
0
B8
0
Bits 0 – 7: Transmit DS0 Channel Bits (B1 to B8). Transmit channel data that has been selected by the transmit
channel monitor select register. B8 is the LSB of the DS0 channel (last bit to be transmitted).
Register Name:
TR.RDS0SEL
Register Description:
Register Address:
Receive Channel Monitor Select
76h
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
RCM4
0
3
RCM3
0
2
RCM2
0
1
RCM1
0
0
RCM0
0
Bits 0 – 4: Receive Channel Monitor Bits (RCM0 to RCM4). RCM0 is the LSB of a 5-bit channel select that
determines which receive DS0 channel data appear in the TR.RDS0M register.
Register Name:
TR.RDS0M
Register Description:
Register Address:
Receive DS0 Monitor Register
77h
Bit #
Name
Default
7
B1
0
6
B2
0
5
B3
0
4
B4
0
3
B5
0
2
B6
0
1
B7
0
0
B8
0
Bits 0 – 7: Receive DS0 Channel Bits (B1 to B8). Receive channel data that has been selected by the receive
channel monitor select register. B8 is the LSB of the DS0 channel (last bit to be received).
254 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.LIC1
Register Description:
Register Address:
Line Interface Control 1
78h
Bit #
Name
Default
7
L2
0
6
L1
0
5
L0
0
4
EGL
0
3
JAS
0
2
JABDS
0
1
DJA
0
0
TPD
0
Bits 5 – 7: Line Build-Out Select (L0 to L2). When using the internal termination, the user needs only to select
000 for 75Ω operation or 001 for 120Ω operation below. This selects the proper voltage levels for 75Ω or 120Ω
operation. Using TT0 and TT1 of the TR.LICR4 register, the user can then select the proper internal source
termination. Line build-outs 100 and 101 are for backwards compatibility with older products only.
E1 Mode
L2
0
0
1
1
L1
0
0
0
0
L0
0
1
0
1
Application
N (1)
1:2
1:2
1:2
1:2
Return Loss
NM
Rt (1) (Ω)
0
0
6.2
11.6
75Ω normal
NM
21dB
21dB
120Ω normal
75Ω with high return loss*
120Ω with high return loss*
*TT0 and TT1 of LIC4 register must be set to 0 in this configuration.
T1 Mode
L2
0
0
0
0
1
1
1
1
L1
0
0
1
1
0
0
1
1
L0
0
1
0
1
0
1
0
1
Application
DSX-1 (0ft to 133ft) / 0dB CSU
DSX-1 (133ft to 266ft)
DSX-1 (266ft to 399ft)
DSX-1 (399ft to 533ft)
DSX-1 (533ft to 655ft)
-7.5dB CSU
N (1)
1:2
1:2
1:2
1:2
1:2
1:2
1:2
1:2
Return Loss
Rt (1) (Ω)
NM
NM
NM
NM
NM
NM
NM
NM
0
0
0
0
0
0
0
0
-15dB CSU
-22.5dB CSU
Bit 4: Receive Equalizer Gain Limit (EGL). This bit controls the sensitivity of the receive equalizer.
T1 Mode
E1 Mode
0 = -36dB (long haul)
1 = -15dB (limited long haul)
0 = -12dB (short haul)
1 = -43dB (long haul)
Bit 3: Jitter Attenuator Select (JAS)
0 = place the jitter attenuator on the receive side
1 = place the jitter attenuator on the transmit side
Bit 2: Jitter Attenuator Buffer Depth Select (JABDS)
0 = 128 bits
1 = 32 bits (use for delay-sensitive applications)
Bit 1: Disable Jitter Attenuator (DJA)
0 = jitter attenuator enabled
1 = jitter attenuator disabled
Bit 0: Transmit Power-Down (TPD)
0 = powers down the transmitter and tri-states the TTIP and TRING pins
1 = normal transmitter operation
255 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TLBC
Register Description:
Register Address:
Transmit Line Build-Out Control
7Dh
Bit #
Name
Default
7
—
0
6
AGCE
0
5
GC5
0
4
GC4
0
3
GC3
0
2
GC2
0
1
GC1
0
0
GC0
0
Bit 6: Automatic Gain Control Enable (AGCE).
0 = use Transmit AGC, TR.TLBC bits 0–5 are “don’t care”
1 = do not use Transmit AGC, TR.TLBC bits 0–5 set nominal level
Bits 0–5: Gain Control Bits (GC0–GC5). The GC0 through GC5 bits control the gain setting for the nonautomatic
gain mode. Use the tables below for setting the recommended values. The LB (line build-out) column refers to the
value in the L0–L2 bits in TR.LIC1 (Line Interface Control 1) register.
NETWORK MODE
LB
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
0
1
4
5
0
1
GC5
1
0
0
1
1
1
0
1
0
0
0
0
1
1
0
1
GC4
0
1
1
0
0
0
1
1
1
1
1
1
0
0
0
1
GC3
0
1
1
0
0
0
0
1
1
0
0
1
0
0
1
1
GC2
1
0
0
0
1
1
0
1
1
1
1
0
0
0
1
1
GC1
1
1
1
0
1
1
1
1
1
0
0
1
1
0
0
1
GC0
0
1
0
0
1
1
1
1
0
1
1
0
0
0
0
1
T1, Impedance Match Off
T1, Impedance Match On
1
1
1
1
0
0
0
0
0
0
1
1
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
0
1
1
1
1
0
0
0
0
E1, Impedance Match Off
E1, Impedance Match On
256 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.LIC2
Register Description:
Register Address:
Line Interface Control 2
79h
Bit #
Name
Default
7
ETS
0
6
LIRST
0
5
IBPV
0
4
TUA1
0
3
JAMUX
0
2
—
0
1
SCLD
0
0
CLDS
0
Bit 7: E1/T1 Select (ETS)
0 = T1 mode selected
1 = E1 mode selected
Bit 6: Line Interface Reset (LIRST). Setting this bit from a 0 to a 1 initiates an internal reset that resets the clock
recovery state machine and recenters the jitter attenuator. Normally this bit is only toggled on power-up. Must be
cleared and set again for a subsequent reset.
Bit 5: Insert BPV (IBPV). A 0-to-1 transition on this bit causes a single BPV to be inserted into the transmit data
stream. Once this bit has been toggled from a 0 to a 1, the device waits for the next occurrence of three
consecutive 1s to insert the BPV. This bit must be cleared and set again for a subsequent error to be inserted.
Bit 4: Transmit Unframed All Ones (TUA1). The polarity of this bit is set such that the device transmits an all-
ones pattern on power-up or device reset. This bit must be set to a 1 to allow the device to transmit data. The
transmission of this data pattern is always timed off of the JACLK.
0 = transmit all ones at TTIP and TRING
1 = transmit data normally
Bit 3: Jitter Attenuator Mux (JAMUX). Controls the source for JACLK.
0 = JACLK sourced from MCLK (2.048MHz or 1.544MHz at MCLK)
1 = JACLK sourced from internal PLL (2.048MHz at MCLK)
Bit 1: Short-Circuit Limit Disable (ETS = 1) (SCLD). Controls the 50mA (RMS) current limiter.
0 = enable 50mA current limiter
1 = disable 50mA current limiter
Bit 0: Custom Line Driver Select (CLDS). Setting this bit to a 1 redefines the operation of the transmit line driver.
When this bit is set to a 1 and TR.LIC1.5 = TR.LIC1.6 = TR.LIC1.7 = 0, the device generates a square wave at the
TTIP and TRING outputs instead of a normal waveform. When this bit is set to a 1 and TR.LIC1.5 = TR.LIC1.6 =
TR.LIC1.7 ≠ 0, the device forces TTIP and TRING outputs to become open-drain drivers instead of their normal
push-pull operation. This bit should be set to 0 for normal operation of the device.
257 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.LIC3
Register Description:
Register Address:
Line Interface Control 3
7Ah
Bit #
Name
Default
7
—
0
6
TCES
0
5
RCES
0
4
MM1
0
3
MM0
0
2
RSCLKE
0
1
TSCLKE
0
0
TAOZ
0
Bit 6: Transmit-Clock Edge Select (TCES). Selects which TDCLKI edge to sample TPOSI and TNEGI.
0 = sample TPOSI and TNEGI on falling edge of TDCLKI
1 = sample TPOSI and TNEGI on rising edge of TDCLKI
Bit 5: Receive-Clock Edge Select (RCES). Selects which RDCLKO edge to update RPOSO and RNEGO.
0 = update RPOSO and RNEGO on rising edge of RDCLKO
1 = update RPOSO and RNEGO on falling edge of RDCLKO
Bits 3 – 4: Monitor Mode (MM0 to MM1)
Internal Linear Gain Boost
MM1
MM0
(dB)
0
0
1
1
0
1
0
1
Normal operation (no boost)
20
26
32
Bit 2: Receive Synchronization G.703 Clock Enable (RSCLKE)
0 = disable 1.544MHz (T1)/2.048MHz (E1) synchronization receive mode
1 = enable 1.544MHz (T1)/2.048MHz (E1) synchronization receive mode
Bit 1: Transmit Synchronization G.703 Clock Enable (TSCLKE)
0 = disable 1.544MHz (T1)/2.048MHz (E1) transmit synchronization clock
1 = enable 1.544MHz (T1)/2.048MHz (E1) transmit synchronization clock
Bit 0: Transmit Alternate Ones and Zeros (TAOZ). Transmit a …101010… pattern (customer disconnect
indication signal) at TTIP and TRING. The transmission of this data pattern is always timed off of TCLKT.
0 = disabled
1 = enabled
258 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.LIC4
Register Description:
Register Address:
Line Interface Control 4
7Bh
Bit #
Name
Default
7
CMIE
0
6
CMII
0
5
MPS1
0
4
MPS0
0
3
TT1
0
2
TT0
0
1
RT1
0
0
RT0
0
Bit 7: CMI Enable (CMIE)
0 = disable CMI mode
1 = enable CMI mode
Bit 6: CMI Invert (CMII)
0 = CMI normal at TTIP and RTIP
1 = invert CMI signal at TTIP and RTIP
Bits 4 – 5: MCLK Prescaler
T1 Mode:
JAMUX
(TR.LIC2.3)
MCLK (MHz)
MPS1
MPS0
1.544
3.088
6.176
12.352
2.048
4.096
8.192
16.384
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
0
0
0
1
1
1
1
E1 Mode:
MCLK
(MHz)
2.048
JAMUX
(TR.LIC2.3)
MPS1
MPS0
0
0
1
1
0
1
0
1
0
0
0
0
4.096
8.192
16.384
Bits 2 – 3: Transmit Termination Select (TT0, TT1)
TT1
0
0
1
1
TT0
0
1
0
1
Internal Transmit-Termination Configuration
Internal transmit-side termination disabled
Internal transmit -side 75Ω enabled
Internal transmit -side 100Ω enabled
Internal transmit -side 120Ω enabled
Bits 0 – 1: Receive Termination Select (RT0, RT1)
RT1
0
0
RT0
0
1
Internal Receive-Termination Configuration
Internal receive-side termination disabled
Internal receive-side 75Ω enabled
1
0
Internal receive-side 100Ω enabled
1
1
Internal receive-side 120Ω enabled
259 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.IAAR
Register Description:
Register Address:
Idle Array Address Register
7Eh
Bit #
Name
Default
7
GRIC
0
6
GTIC
0
5
IAA5
0
4
IAA4
0
3
IAA3
0
2
IAA2
0
1
IAA1
0
0
IAA0
0
Bit 7: Global Receive-Idle Code (GRIC). Setting this bit causes all receive channels to be set to the idle code
written to the TR.PCICR register. This bit must be set = 0 for read operations. The value in bits IAA0–IAA5 must be
a valid transmit channel (01h to 20h for E1 mode; 01h to 18h for T1 mode).
Bit 6: Global Transmit-Idle Code (GTIC). Setting this bit causes all transmit channels to be set to the idle code
written to the PCICR register. This bit must be set = 0 for read operations. The value in bits IAA0–IAA5 must be a
valid transmit channel (01h to 20h for E1 mode; 01h to 18h for T1 mode).
GRIC
GTIC
FUNCTION
0
0
1
1
0
1
0
1
Updates a single transmit or receive channel
Updates all transmit channels
Updates all receive channels
Updates all transmit and receive channels
Bits 0 – 5: Channel Pointer Address Bits (IAA0 to IAA5). These bits select the channel to be programmed with
the idle code defined in the TR.PCICR register. IAA0 is the LSB of the 5-bit channel code. Channel 1 is 01h.
Register Name:
TR.PCICR
Register Description:
Register Address:
Per-Channel Idle Code Register
7Fh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Bits 0 – 7: Per-Channel Idle-Code Bits (C0 to C7). This register defines the idle code to be programmed in the
channel selected by the TR.IAAR register. C0 is the LSB of the idle code (this bit is transmitted last).
Register Name:
TR.TCICE1
Register Description:
Register Address:
Transmit-Channel Idle-Code Enable Register 1
80h
Bit #
Name
Default
7
CH8
0
6
CH7
0
5
CH6
0
4
CH5
0
3
CH4
0
2
CH3
0
1
CH2
0
0
CH1
0
Bits 0 – 7: Transmit Channels 1 to 8 Code Insertion Control Bits (CH1 to CH8)
0 = do not insert data from the idle-code array into the transmit data stream
1 = insert data from the idle-code array into the transmit data stream
260 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TCICE2
Register Description:
Register Address:
Transmit-Channel Idle-Code Enable Register 2
81h
Bit #
Name
Default
7
CH16
0
6
CH15
0
5
CH14
0
4
CH13
0
3
CH12
0
2
CH11
0
1
CH10
0
0
CH9
0
Bits 0 – 7: Transmit Channels 9 to 16 Code Insertion Control Bits (CH9 to CH16)
0 = do not insert data from the idle-code array into the transmit data stream
1 = insert data from the idle code-array into the transmit data stream
Register Name:
TR.TCICE3
Register Description:
Register Address:
Transmit-Channel Idle-Code Enable Register 3
82h
Bit #
Name
Default
7
CH24
0
6
CH23
0
5
CH22
0
4
CH21
0
3
CH20
0
2
CH19
0
1
CH18
0
0
CH17
0
Bits 0 – 7: Transmit Channels 17 to 24 Code Insertion Control Bits (CH17 to CH24)
0 = do not insert data from the idle-code array into the transmit data stream
1 = insert data from the idle code-array into the transmit data stream
Register Name:
TR.TCICE4
Register Description:
Register Address:
Transmit-Channel Idle-Code Enable Register 4
83h
Bit #
Name
Default
7
CH32
0
6
CH31
0
5
CH30
0
4
CH29
0
3
CH28
0
2
CH27
0
1
CH26
0
0
CH25
0
Bits 0 – 7: Transmit Channels 25 to 32 Code Insertion Control Bits (CH25 to CH32)
0 = do not insert data from the idle-code array into the transmit data stream
1 = insert data from the idle-code array into the transmit data stream
Register Name:
TR.RCICE1
Register Description:
Register Address:
Receive-Channel Idle-Code Enable Register 1
84h
Bit #
Name
Default
7
CH8
0
6
CH7
0
5
CH6
0
4
CH5
0
3
CH4
0
2
CH3
0
1
CH2
0
0
CH1
0
Bits 0 – 7: Receive Channels 1 to 8 Code Insertion Control Bits (CH1 to CH8)
0 = do not insert data from the idle-code array into the receive data stream
1 = insert data from the idle-code array into the receive data stream
261 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RCICE2
Register Description:
Register Address:
Receive-Channel Idle-Code Enable Register 2
85h
Bit #
Name
Default
7
CH16
0
6
CH15
0
5
CH14
0
4
CH13
0
3
CH12
0
2
CH11
0
1
CH10
0
0
CH9
0
Bits 0 – 7: Receive Channels 9 to 16 Code Insertion Control Bits (CH9 to CH16)
0 = do not insert data from the idle-code array into the receive data stream
1 = insert data from the idle-code array into the receive data stream
Register Name:
TR.RCICE3
Register Description:
Register Address:
Receive-Channel Idle-Code Enable Register 3
86h
Bit #
Name
Default
7
CH24
0
6
CH23
0
5
CH22
0
4
CH21
0
3
CH20
0
2
CH19
0
1
CH18
0
0
CH17
0
Bits 0 – 7: Receive Channels 17 to 24 Code Insertion Control Bits (CH17 to CH24)
0 = do not insert data from the idle-code array into the receive data stream
1 = insert data from the idle-code array into the receive data stream
Register Name:
TR.RCICE4
Register Description:
Register Address:
Receive-Channel Idle-Code Enable Register 4
87h
Bit #
Name
Default
7
CH32
0
6
CH31
0
5
CH30
0
4
CH29
0
3
CH28
0
2
CH27
0
1
CH26
0
0
CH25
0
Bits 0 – 7: Receive Channels 25 to 32 Code Insertion Control Bits (CH25 to CH32)
0 = do not insert data from the idle-code array into the receive data stream
1 = insert data from the idle-code array into the receive data stream
Register Name:
TR.RCBR1
Register Description:
Register Address:
Receive Channel Blocking Register 1
88h
Bit #
Name
Default
7
CH8
0
6
CH7
0
5
CH6
0
4
CH5
0
3
CH4
0
2
CH3
0
1
CH2
0
0
CH1
0
Bits 0 – 7: Receive Channels 1 to 8 Channel Blocking Control Bits (CH1 to CH8)
0 = force the RCHBLK pin to remain low during this channel time
1 = force the RCHBLK pin high during this channel time
262 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RCBR2
Register Description:
Register Address:
Receive Channel Blocking Register 2
89h
Bit #
Name
Default
7
CH16
0
6
CH15
0
5
CH14
0
4
CH13
0
3
CH12
0
2
CH11
0
1
CH10
0
0
CH9
0
Bits 0 – 7: Receive Channels 9 to 16 Channel Blocking Control Bits (CH9 to CH16)
0 = force the RCHBLK pin to remain low during this channel time
1 = force the RCHBLK pin high during this channel time
Register Name:
TR.RCBR3
Register Description:
Register Address:
Receive Channel Blocking Register 3
8Ah
Bit #
Name
Default
7
CH24
0
6
CH23
0
5
CH22
0
4
CH21
0
3
CH20
0
2
CH19
0
1
CH18
0
0
CH17
0
Bits 0 – 7: Receive Channels 17 to 24 Channel Blocking Control Bits (CH17 to CH24)
0 = force the RCHBLK pin to remain low during this channel time
1 = force the RCHBLK pin high during this channel time
Register Name:
TR.RCBR4
Register Description:
Register Address:
Receive Channel Blocking Register 4
8Bh
Bit #
Name
Default
7
CH32
0
6
CH31
0
5
CH30
0
4
CH29
0
3
CH28
0
2
CH27
0
1
CH26
0
0
CH25
0
Bits 0 – 7: Receive Channels 25 to 32 Channel Blocking Control Bits (CH25 to CH32)
0 = force the RCHBLK pin to remain low during this channel time
1 = force the RCHBLK pin high during this channel time
263 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TCBR1
Register Description:
Register Address:
Transmit Channel Blocking Register 1
8Ch
Bit #
Name
Default
7
CH8
0
6
CH7
0
5
CH6
0
4
CH5
0
3
CH4
0
2
CH3
0
1
CH2
0
0
CH1
0
Bits 0 – 7: Transmit Channels 1 to 8 Channel Blocking Control Bits (CH1 to CH8)
0 = force the TCHBLK pin to remain low during this channel time
1 = force the TCHBLK pin high during this channel time
Register Name:
TR.TCBR2
Register Description:
Register Address:
Transmit Channel Blocking Register 2
8Dh
Bit #
Name
Default
7
CH16
0
6
CH15
0
5
CH14
0
4
CH13
0
3
CH12
0
2
CH11
0
1
CH10
0
0
CH9
0
Bits 0 – 7: Transmit Channels 9 to 16 Channel Blocking Control Bits (CH9 to CH16)
0 = force the TCHBLK pin to remain low during this channel time
1 = force the TCHBLK pin high during this channel time
Register Name:
TR.TCBR3
Register Description:
Register Address:
Transmit Channel Blocking Register 3
8Eh
Bit #
Name
Default
7
CH24
0
6
CH23
0
5
CH22
0
4
CH21
0
3
CH20
0
2
CH19
0
1
CH18
0
0
CH17
0
Bits 0 – 7: Transmit Channels 17 to 24 Channel Blocking Control Bits (CH17 to CH24)
0 = force the TCHBLK pin to remain low during this channel time
1 = force the TCHBLK pin high during this channel time
Register Name:
TR.TCBR4
Register Description:
Register Address:
Transmit Channel Blocking Register 4
8Fh
Bit #
Name
Default
7
CH32
0
6
CH31
0
5
CH30
0
4
CH29
0
3
CH28
0
2
CH27
0
1
CH26
0
0
CH25
0
Bits 0 – 7: Transmit Channels 25 to 32 Channel Blocking Control Bits (CH25 to CH32)
0 = force the TCHBLK pin to remain low during this channel time
1 = force the TCHBLK pin high during this channel time
264 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.H1TC, TR.H2TC
Register Description:
HDLC #1 Transmit Control
HDLC #2 Transmit Control
90h, A0h
Register Address:
Bit #
Name
Default
7
NOFS
0
6
TEOML
0
5
THR
0
4
THMS
0
3
TFS
0
2
TEOM
0
1
TZSD
0
0
TCRCD
0
Bit 7: Number of Flags Select (NOFS)
0 = send one flag between consecutive messages
1 = send two flags between consecutive messages
Bit 6: Transmit End of Message and Loop (TEOML). To loop on a message, this bit should be set to a 1 just
before the last data byte of an HDLC packet is written into the transmit FIFO. The message repeats until the user
clears this bit or a new message is written to the transmit FIFO. If the host clears the bit, the looping message
completes, then flags are transmitted until a new message is written to the FIFO. If the host terminates the loop by
writing a new message to the FIFO, the loop terminates, one or two flags are transmitted, and the new message
starts. If not disabled through TCRCD, the transmitter automatically appends a 2-byte CRC code to the end of all
messages. This is useful for transmitting consecutive SS7 FISUs without host intervention.
Bit 5: Transmit HDLC Reset (THR). Resets the transmit HDLC controller and flushes the transmit FIFO. An abort
followed by 7Eh or FFh flags/idle is transmitted until a new packet is initiated by writing new data into the FIFO.
Must be cleared and set again for a subsequent reset.
0 = normal operation
1 = reset transmit HDLC controller and flush the transmit FIFO
Bit 4: Transmit HDLC Mapping Select (THMS)
0 = transmit HDLC assigned to channels
1 = transmit HDLC assigned to FDL (T1 mode), Sa bits (E1 mode)
Bit 3: Transmit Flag/Idle Select (TFS). This bit selects the intermessage fill character after the closing and before
the opening flags (7Eh).
0 = 7Eh
1 = FFh
Bit 2: Transmit End of Message (TEOM). Should be set to a 1 just before the last data byte of an HDLC packet is
written into the transmit FIFO at HxTF. If not disabled through TCRCD, the transmitter automatically appends a 2-
byte CRC code to the end of the message.
Bit 1: Transmit Zero-Stuffer Defeat (TZSD). The zero-stuffer function automatically inserts a 0 in the message
field (between the flags) after five consecutive 1s to prevent the emulation of a flag or abort sequence by the data
pattern. The receiver automatically removes (destuffs) any 0 after five 1s in the message field.
0 = enable the zero stuffer (normal operation)
1 = disable the zero stuffer
Bit 0: Transmit CRC Defeat (TCRCD). A 2-byte CRC code is automatically appended to the outbound message.
This bit can be used to disable the CRC function.
0 = enable CRC generation (normal operation)
1 = disable CRC generation
265 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
Register Description:
TR.H1FC, TR.H2FC
HDLC # 1 FIFO Control
HDLC # 2 FIFO Control
91h, A1h
Register Address:
Bit #
Name
Default
7
—
0
6
—
0
5
TFLWM2
0
4
TFLWM1
0
3
TFLWM0
0
2
1
0
RFHWM2 RFHWM1 RFHWM0
0
0
0
Bits 3 – 5: Transmit FIFO Low-Watermark Select (TFLWM0 to TFLWM2)
Transmit FIFO Watermark
TFLWM2
TFLWM1
TFLWM0
(bytes)
4
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
16
32
48
64
80
96
112
Bits 0 – 2: Receive FIFO High-Watermark Select (RFHWM0 to RFHWM2)
Receive FIFO Watermark
RFHWM2
RFHWM1
RFHWM0
(bytes)
4
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
16
32
48
64
80
96
112
266 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
TR.H1RCS1, TR.H1RCS2, TR.H1RCS3, TR.H1RCS4
Register Name:
TR.H2RCS1, TR.H2RCS2, TR.H2RCS3, TR.H2RCS4
HDLC # 1 Receive Channel Select
HDLC # 2 Receive Channel Select
92h, 93h, 94h, 95h
Register Description:
Register Address:
A2h, A3h, A4h, A5h
Bit #
Name
Default
7
RHCS7
0
6
RHCS6
0
5
RHCS5
0
4
RHCS4
0
3
RHCS3
0
2
RHCS2
0
1
RHCS1
0
0
RHCS0
0
Bit 7: Receive HDLC Channel Select Bit 7 (RHCS7). Select Channel 8, 16, 24, or 32.
Bit 6: Receive HDLC Channel Select Bit 6 (RHCS6). Select Channel 7, 15, 23, or 31.
Bit 5: Receive HDLC Channel Select Bit 5 (RHCS5). Select Channel 6, 14, 22, or 30.
Bit 4: Receive HDLC Channel Select Bit 4 (RHCS4). Select Channel 5, 13, 21, or 29.
Bit 3: Receive HDLC Channel Select Bit 3 (RHCS3). Select Channel 4, 12, 20, or 28.
Bit 2: Receive HDLC Channel Select Bit 2 (RHCS2). Select Channel 3, 11, 19, or 27.
Bit 1: Receive HDLC Channel Select Bit 1 (RHCS1). Select Channel 2, 10, 18, or 26.
Bit 0: Receive HDLC Channel Select Bit 0 (RHCS0). Select Channel 1, 9, 17, or 25.
267 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.H1RTSBS, TR.H2RTSBS
Register Description:
HDLC # 1 Receive Time Slot Bits/Sa Bits Select
HDLC # 2 Receive Time Slot Bits/Sa Bits Select
96h, A6h
Register Address:
Bit #
Name
Default
7
RCB8SE
0
6
RCB7SE
0
5
RCB6SE
0
4
RCB5SE
0
3
RCB4SE
0
2
RCB3SE
0
1
RCB2SE
0
0
RCB1SE
0
Bit 7: Receive Channel Bit 8 Suppress Enable (RCB8SE). MSB of the channel. Set to 1 to stop this bit from
being used.
Bit 6: Receive Channel Bit 7 Suppress Enable (RCB7SE). Set to 1 to stop this bit from being used.
Bit 5: Receive Channel Bit 6 Suppress Enable (RCB6SE). Set to 1 to stop this bit from being used.
Bit 4: Receive Channel Bit 5 Suppress Enable/Sa4 Bit Enable (RCB5SE). Set to 1 to stop this bit from being
used.
Bit 3: Receive Channel Bit 4 Suppress Enable/Sa5 Bit Enable (RCB4SE). Set to 1 to stop this bit from being
used.
Bit 2: Receive Channel Bit 3 Suppress Enable/Sa6 Bit Enable (RCB3SE). Set to 1 to stop this bit from being
used.
Bit 1: Receive Channel Bit 2 Suppress Enable/Sa7 Bit Enable (RCB2SE). Set to 1 to stop this bit from being
used.
Bit 0: Receive Channel Bit 1 Suppress Enable/Sa8 Bit Enable (RCB1SE ). LSB of the channel. Set to 1 to stop
this bit from being used.
268 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
TR.H1TCS1, TR.H1TCS2, TR.H1TCS3, TR.H1TCS4
Register Name:
TR.H2TCS1, TR.H2TCS2, TR.H2TCS3, TR.H2TCS4
HDLC # 1 Transmit Channel Select
HDLC # 2 Transmit Channel Select
97h, 98h, 99h, 9Ah
Register Description:
Register Address:
A7h, A8h, A9h, AAh
Bit #
Name
Default
7
THCS7
0
6
THCS6
0
5
THCS5
0
4
THCS4
0
3
THCS3
0
2
THCS2
0
1
THCS1
0
0
THCS0
0
Bit 7: Transmit HDLC Channel Select Bit 7 (THCS7). Select Channel 8, 16, 24, or 32.
Bit 6: Transmit HDLC Channel Select Bit 6 (THCS6). Select Channel 7, 15, 23, or 31.
Bit 5: Transmit HDLC Channel Select Bit 5 (THCS5). Select Channel 6, 14, 22, or 30.
Bit 4: Transmit HDLC Channel Select Bit 4 (THCS4). Select Channel 5, 13, 21, or 29.
Bit 3: Transmit HDLC Channel Select Bit 3 (THCS3). Select Channel 4, 12, 20, or 28.
Bit 2: Transmit HDLC Channel Select Bit 2 (THCS2). Select Channel 3, 11, 19, or 27.
Bit 1: Transmit HDLC Channel Select Bit 1 (THCS1). Select Channel 2, 10, 18, or 26.
Bit 0: Transmit HDLC Channel Select Bit 0 (THCS0). Select Channel 1, 9, 17, or 25.
269 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.H1TTSBS, TR.H2TTSBS
Register Description:
HDLC # 1 Transmit Time Slot Bits/Sa Bits Select
HDLC # 2 Transmit Time Slot Bits/Sa Bits Select
9Bh, ABh
Register Address:
Bit #
Name
Default
7
TCB8SE
0
6
TCB7SE
0
5
TCB6SE
0
4
TCB5SE
0
3
TCB4SE
0
2
TCB3SE
0
1
TCB2SE
0
0
TCB1SE
0
Bit 7: Transmit Channel Bit 8 Suppress Enable (TCB1SE). MSB of the channel. Set to 1 to stop this bit from
being used.
Bit 6: Transmit Channel Bit 7 Suppress Enable (TCB1SE). Set to 1 to stop this bit from being used.
Bit 5: Transmit Channel Bit 6 Suppress Enable (TCB1SE). Set to 1 to stop this bit from being used.
Bit 4: Transmit Channel Bit 5 Suppress Enable/Sa4 Bit Enable (TCB1SE). Set to 1 to stop this bit from being
used.
Bit 3: Transmit Channel Bit 4 Suppress Enable/Sa5 Bit Enable (TCB1SE). Set to 1 to stop this bit from being
used.
Bit 2: Transmit Channel Bit 3 Suppress Enable/Sa6 Bit Enable (TCB1SE). Set to 1 to stop this bit from being
used.
Bit 1: Transmit Channel Bit 2 Suppress Enable/Sa7 Bit Enable (TCB1SE). Set to 1 to stop this bit from being
used.
Bit 0: Transmit Channel Bit 1 Suppress Enable/Sa8 Bit Enable (TCB1SE). LSB of the channel. Set to 1 to stop
this bit from being used.
Register Name:
TR.H1RPBA, TR.H2RPBA
Register Description:
HDLC # 1 Receive Packet Bytes Available
HDLC # 2 Receive Packet Bytes Available
9Ch, ACh
Register Address:
Bit #
Name
Default
7
MS
0
6
RPBA6
0
5
RPBA5
0
4
RPBA4
0
3
RPBA3
0
2
RPBA2
0
1
RPBA1
0
0
RPBA0
0
Bit 7: Message Status (MS)
0 = bytes indicated by RPBA0 through RPBA6 are the end of a message. Host must check the INFO5 or
INFO6 register for details.
1 = bytes indicated by RPBA0 through RPBA6 are the beginning or continuation of a message. The host
does not need to check the INFO5 or INFO6 register.
Bits 0 – 6: Receive FIFO Packet Bytes Available Count (RPBA0 to RPBA6). RPBA0 is the LSB.
270 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.H1TF, TR.H2TF
Register Description:
HDLC # 1 Transmit FIFO
HDLC # 2 Transmit FIFO
9Dh, ADh
Register Address:
Bit #
Name
Default
7
THD7
0
6
THD6
0
5
THD5
0
4
THD4
0
3
THD3
0
2
THD2
0
1
THD1
0
0
THD0
0
Bit 7: Transmit HDLC Data Bit 7 (THD7). MSB of an HDLC packet data byte.
Bit 6: Transmit HDLC Data Bit 6 (THD6)
Bit 5: Transmit HDLC Data Bit 5 (THD5)
Bit 4: Transmit HDLC Data Bit 4 (THD4)
Bit 3: Transmit HDLC Data Bit 3 (THD3)
Bit 2: Transmit HDLC Data Bit 2 (THD2)
Bit 1: Transmit HDLC Data Bit 1 (THD1)
Bit 0: Transmit HDLC Data Bit 0 (THD0). LSB of an HDLC packet data byte.
Register Name:
Register Description:
TR.H1RF, TR.H2RF
HDLC # 1 Receive FIFO
HDLC # 2 Receive FIFO
9Eh, AEh
Register Address:
Bit #
Name
Default
7
RHD7
0
6
RHD6
0
5
RHD5
0
4
RHD4
0
3
RHD3
0
2
RHD2
0
1
RHD1
0
0
RHD0
0
Bit 7: Receive HDLC Data Bit 7 (RHD7). MSB of an HDLC packet data byte.
Bit 6: Receive HDLC Data Bit 6 (RHD6)
Bit 5: Receive HDLC Data Bit 5 (RHD5)
Bit 4: Receive HDLC Data Bit 4 (RHD4)
Bit 3: Receive HDLC Data Bit 3 (RHD3)
Bit 2: Receive HDLC Data Bit 2 (RHD2)
Bit 1: Receive HDLC Data Bit 1 (RHD1)
Bit 0: Receive HDLC Data Bit 0 (RHD0). LSB of an HDLC packet data byte.
271 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
TR.H1TFBA, TR.H2TFBA
Register Name:
Register Description:
HDLC # 1 Transmit FIFO Buffer Available
HDLC # 2 Transmit FIFO Buffer Available
9Fh, Afh
Register Address:
Bit #
Name
Default
7
TFBA7
0
6
TFBA6
0
5
TFBA5
0
4
TFBA4
0
3
TFBA3
0
2
TFBA2
0
1
TFBA1
0
0
TFBA0
0
Bits 0 – 7: Transmit FIFO Bytes Available (TFBAO to TFBA7). TFBA0 is the LSB.
Register Name:
TR.IBCC
Register Description:
Register Address:
In-Band Code Control Register
B6h
Bit #
Name
Default
7
TC1
0
6
TC0
0
5
RUP2
0
4
RUP1
0
3
RUP0
0
2
RDN2
0
1
RDN1
0
0
RDN0
0
Bits 6 – 7: Transmit Code Length Definition Bits (TC0 to TC1)
TC1
0
TC0
0
Length Selected (bits)
5
0
1
1
0
6/3
7
1
1
16/8/4/2/1
Bits 3 – 5: Receive Up-Code Length Definition Bits (RUP0 to RUP2)
RUP2
RUP1
RUP0
Length Selected (bits)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
7
8/16
Bits 0 – 2: Receive Down-Code Length Definition Bits (RDN0 to RDN2)
RDN2
RDN1
RDN0
Length Selected (bits)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
7
8/16
272 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TCD1
Register Description:
Register Address:
Transmit Code-Definition Register 1
B7h
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Bit 7: Transmit Code-Definition Bit 7 (C7). First bit of the repeating pattern.
Bits 3 – 6: Transmit Code-Definition Bits 3–6 (C3–C6)
Bit 2: Transmit Code-Definition Bit 2 (C2). A don’t care if a 5-bit length is selected.
Bit 1: Transmit Code-Definition Bit 1 (C1). A don’t care if a 5-bit or 6-bit length is selected.
Bit 0: Transmit Code-Definition Bit 0 (C0). A don’t care if a 5-, 6-, or 7-bit length is selected.
Register Name:
TR.TCD2
Register Description:
Register Address:
Transmit Code Definition Register 2
B8h
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Least significant byte of 16 bit code.
Bits 0 – 7: Transmit Code-Definition Bits 0–7 (C0–C7). A don’t care if a 5-, 6-, or 7-bit length is selected.
273 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RUPCD1
Register Description:
Register Address:
Receive Up-Code Definition Register 1
B9h
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Note: Writing this register resets the detector’s integration period.
Bit 7: Receive Up-Code Definition Bit 7 (C7). First bit of the repeating pattern.
Bit 6: Receive Up-Code Definition Bit 6 (C6). A don’t care if a 1-bit length is selected.
Bit 5: Receive Up-Code Definition Bit 5 (C5). A don’t care if a 1-bit or 2-bit length is selected.
Bit 4: Receive Up-Code Definition Bit 4 (C4). A don’t care if a 1-bit to 3-bit length is selected.
Bit 3: Receive Up-Code Definition Bit 3 (C3). A don’t care if a 1-bit to 4-bit length is selected.
Bit 2: Receive Up-Code Definition Bit 2 (C2). A don’t care if a 1-bit to 5-bit length is selected.
Bit 1: Receive Up-Code Definition Bit 1 (C1). A don’t care if a 1-bit to 6-bit length is selected.
Bit 0: Receive Up-Code Definition Bit 0 (C0). A don’t care if a 1-bit to 7-bit length is selected.
Register Name:
TR.RUPCD2
Register Description:
Register Address:
Receive Up-Code Definition Register 2
BAh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Bits 0 – 7: Receive Up-Code Definition Bits 0–7 (C0–C7). A don’t care if a 1-bit to 7-bit length is selected.
274 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RDNCD1
Register Description:
Register Address:
Receive Down-Code Definition Register 1
BBh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Note: Writing this register resets the detector’s integration period.
Bit 7: Receive Down-Code Definition Bit 7 (C7). First bit of the repeating pattern.
Bit 6: Receive Down-Code Definition Bit 6 (C6). A don’t care if a 1-bit length is selected.
Bit 5: Receive Down-Code Definition Bit 5 (C5). A don’t care if a 1-bit or 2-bit length is selected.
Bit 4: Receive Down-Code Definition Bit 4 (C4). A don’t care if a 1-bit to 3-bit length is selected.
Bit 3: Receive Down-Code Definition Bit 3 (C3). A don’t care if a 1-bit to 4-bit length is selected.
Bit 2: Receive Down-Code Definition Bit 2 (C2). A don’t care if a 1-bit to 5-bit length is selected.
Bit 1: Receive Down-Code Definition Bit 1 (C1). A don’t care if a 1-bit to 6-bit length is selected.
Bit 0: Receive Down-Code Definition Bit 0 (C0). A don’t care if a 1-bit to 7-bit length is selected.
Register Name:
TR.RDNCD2
Register Description:
Register Address:
Receive Down-Code Definition Register 2
BCh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Bits 0 – 7: Receive Down-Code Definition Bits 0–7 (C0–C7). A don’t care if a 1-bit to 7-bit length is selected.
275 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RSCC
Register Description:
Register Address:
In-Band Receive Spare Control Register
BDh
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
—
0
2
RSC2
0
1
RSC1
0
0
RSC0
0
Bits 3 – 7: Unused, must be set to 0 for proper operation
Bits 0 – 2: Receive Spare Code Length Definition Bits (RSC0 to RSC2)
RSC2
RSC1
RSC0
Length Selected (bits)
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
7
8/16
276 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RSCD1
Register Description:
Register Address:
Receive Spare-Code Definition Register 1
BEh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Note: Writing this register resets the detector’s integration period.
Bit 7: Receive Spare-Code Definition Bit 7 (C7). First bit of the repeating pattern.
Bit 6: Receive Spare-Code Definition Bit 6 (C6). A don’t care if a 1-bit length is selected.
Bit 5: Receive Spare-Code Definition Bit 5 (C5). A don’t care if a 1-bit or 2-bit length is selected.
Bit 4: Receive Spare-Code Definition Bit 4 (C4). A don’t care if a 1-bit to 3-bit length is selected.
Bit 3: Receive Spare-Code Definition Bit 3 (C3). A don’t care if a 1-bit to 4-bit length is selected.
Bit 2: Receive Spare-Code Definition Bit 2 (C2). A don’t care if a 1-bit to 5-bit length is selected.
Bit 1: Receive Spare-Code Definition Bit 1 (C1). A don’t care if a 1-bit to 6-bit length is selected.
Bit 0: Receive Spare-Code Definition Bit 0 (C0). A don’t care if a 1-bit to 7-bit length is selected.
Register Name:
TR.RSCD2
Register Description:
Register Address:
Receive Spare Code Definition Register 2
BFh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Bits 0 – 7: Receive Spare-Code Definition Bits 0–7 (C0–C7). A don’t care if a 1-bit to 7-bit length is selected.
277 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
TR.RFDL (TR.BOCC.4 = 1)
Register Name:
Register Description:
Register Address:
Receive FDL Register
C0h
Bit #
Name
Default
7
—
0
6
—
0
5
RBOC5
0
4
RBOC4
0
3
RBOC3
0
2
RBOC2
0
1
RBOC1
0
0
RBOC0
0
RFDL register bit definitions when TR.BOCC.4 = 1:
Bit 5: BOC Bit 5 (RBOC5)
Bit 4: BOC Bit 4 (RBOC4)
Bit 3: BOC Bit 3 (RBOC3)
Bit 2: BOC Bit 2 (RBOC2)
Bit 1: BOC Bit 1 (RBOC1)
Bit 0: BOC Bit 0 (RBOC0)
Register Name:
Register Description:
Register Address:
TR.RFDL (TR.BOCC.4 = 0)
Receive FDL Register
C0h
Bit #
Name
Default
7
RFDL7
0
6
RFDL6
0
5
RFDL5
0
4
RFDL4
0
3
RFDL3
0
2
RFDL2
0
1
RFDL1
0
0
RFDL0
0
The receive FDL register (TR.RFDL) reports the incoming FDL or the incoming Fs bits. The LSB is received first.
Bit 7: Receive FDL Bit 7 (RFDL7). MSB of the received FDL code.
Bit 6: Receive FDL Bit 6 (RFDL6)
Bit 5: Receive FDL Bit 5 (RFDL5)
Bit 4: Receive FDL Bit 4 (RFDL4)
Bit 3: Receive FDL Bit 3 (RFDL3)
Bit 2: Receive FDL Bit 2 (RFDL2)
Bit 1: Receive FDL Bit 1 (RFDL1)
Bit 0: Receive FDL Bit 0 (RFDL0). LSB of the received FDL code.
278 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TFDL
Register Description:
Register Address:
Transmit FDL Register
C1h
Bit #
Name
Default
7
TFDL7
0
6
TFDL6
0
5
TFDL5
0
4
TFDL4
0
3
TFDL3
0
2
TFDL2
0
1
TFDL1
0
0
TFDL0
0
Note: Also used to insert Fs framing pattern in D4 framing mode.
The transmit FDL register (TR.TFDL) contains the FDL information that is to be inserted on a byte basis into the
outgoing T1 data stream. The LSB is transmitted first.
Bit 7: Transmit FDL Bit 7 (TFDL7). MSB of the transmit FDL code.
Bit 6: Transmit FDL Bit 6 (TFDL6)
Bit 5: Transmit FDL Bit 5 (TFDL5)
Bit 4: Transmit FDL Bit 4 (TFDL4)
Bit 3: Transmit FDL Bit 3 (TFDL3)
Bit 2: Transmit FDL Bit 2 (TFDL2)
Bit 1: Transmit FDL Bit 1 (TFDL1)
Bit 0: Transmit FDL Bit 0 (TFDL0). LSB of the transmit FDL code.
Register Name:
Register Description:
TR.RFDLM1, TR.RFDLM2
Receive FDL Match Register 1
Receive FDL Match Register 2
C2h, C3h
Register Address:
Bit #
Name
Default
7
RFDLM7
0
6
RFDLM6
0
5
RFDLM5
0
4
RFDLM4
0
3
RFDLM3
0
2
RFDLM2
0
1
0
RFDLM1 RFDLM0
0
0
Bit 7: Receive FDL Match Bit 7 (RFDLM7). MSB of the FDL match code.
Bit 6: Receive FDL Match Bit 6 (RFDLM6)
Bit 5: Receive FDL Match Bit 5 (RFDLM5)
Bit 4: Receive FDL Match Bit 4 (RFDLM4)
Bit 3: Receive FDL Match Bit 3 (RFDLM3)
Bit 2: Receive FDL Match Bit 2 (RFDLM2)
Bit 1: Receive FDL Match Bit 1 (RFDLM1)
Bit 0: Receive FDL Match Bit 0 (RFDLM0). LSB of the FDL match code.
279 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RAF
Register Description:
Register Address:
Receive Align Frame Register
C6h
Bit #
Name
Default
7
Si
0
6
0
0
5
0
0
4
1
0
3
1
0
2
0
0
1
1
0
0
1
0
Bit 7: International Bit (Si)
Bit 6: Frame Alignment Signal Bit (0)
Bit 5: Frame Alignment Signal Bit (0)
Bit 4: Frame Alignment Signal Bit (1)
Bit 3: Frame Alignment Signal Bit (1)
Bit 2: Frame Alignment Signal Bit (0)
Bit 1: Frame Alignment Signal Bit (1)
Bit 0: Frame Alignment Signal Bit (1)
Register Name:
TR.RNAF
Register Description:
Register Address:
Receive Nonalign Frame Register
C7h
Bit #
Name
Default
7
Si
0
6
1
0
5
A
0
4
Sa4
0
3
Sa5
0
2
Sa6
0
1
Sa7
0
0
Sa8
0
Bit 7: International Bit (Si)
Bit 6: Frame Nonalignment Signal Bit (1)
Bit 5: Remote Alarm (A)
Bit 4: Additional Bit 4 (Sa4)
Bit 3: Additional Bit 5 (Sa5)
Bit 2: Additional Bit 6 (Sa6)
Bit 1: Additional Bit 7 (Sa7)
Bit 0: Additional Bit 8 (Sa8)
280 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RSiAF
Register Description:
Register Address:
Received Si Bits of the Align Frame
C8h
Bit #
Name
Default
7
SiF0
0
6
SiF2
0
5
SiF4
0
4
SiF6
0
3
SiF8
0
2
SiF10
0
1
SiF12
0
0
SiF14
0
Bit 7: Si Bit of Frame 0 (SiF0)
Bit 6: Si Bit of Frame 2 (SiF2)
Bit 5: Si Bit of Frame 4 (SiF4)
Bit 4: Si Bit of Frame 6 (SiF6)
Bit 3: Si Bit of Frame 8 (SiF8)
Bit 2: Si Bit of Frame 10 (SiF10)
Bit 1: Si Bit of Frame 12 (SiF12)
Bit 0: Si Bit of Frame 14 (SiF14)
Register Name:
TR.RSiNAF
Register Description:
Register Address:
Received Si Bits of the Nonalign Frame
C9h
Bit #
Name
Default
7
SiF1
0
6
SiF3
0
5
SiF5
0
4
SiF7
0
3
SiF9
0
2
SiF11
0
1
SiF13
0
0
SiF15
0
Bit 7: Si Bit of Frame 1 (SiF1)
Bit 6: Si Bit of Frame 3 (SiF3)
Bit 5: Si Bit of Frame 5 (SiF5)
Bit 4: Si Bit of Frame 7 (SiF7)
Bit 3: Si Bit of Frame 9 (SiF9)
Bit 2: Si Bit of Frame 11 (SiF11)
Bit 1: Si Bit of Frame 13 (SiF13)
Bit 0: Si Bit of Frame 15 (SiF15)
281 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RRA
Register Description:
Register Address:
Received Remote Alarm
Cah
Bit #
Name
Default
7
RRAF1
0
6
RRAF3
0
5
RRAF5
0
4
RRAF7
0
3
RRAF9
0
2
RRAF11
0
1
RRAF13
0
0
RRAF15
0
Bit 7: Remote Alarm Bit of Frame 1 (RRAF1)
Bit 6: Remote Alarm Bit of Frame 3 (RRAF3)
Bit 5: Remote Alarm Bit of Frame 5 (RRAF5)
Bit 4: Remote Alarm Bit of Frame 7 (RRAF7)
Bit 3: Remote Alarm Bit of Frame 9 (RRAF9)
Bit 2: Remote Alarm Bit of Frame 11 (RRAF11)
Bit 1: Remote Alarm Bit of Frame 13 (RRAF13)
Bit 0: Remote Alarm Bit of Frame 15 (RRAF15)
Register Name:
TR.RSa4
Register Description:
Register Address:
Received Sa4 Bits
CBh
Bit #
Name
Default
7
RSa4F1
0
6
RSa4F3
0
5
RSa4F5
0
4
RSa4F7
0
3
RSa4F9
0
2
RSa4F11
0
1
RSa4F13
0
0
RSa4F15
0
Bit 7: Sa4 Bit of Frame 1 (RSa4F1)
Bit 6: Sa4 Bit of Frame 3 (RSa4F3)
Bit 5: Sa4 Bit of Frame 5(RSa4F5)
Bit 4: Sa4 Bit of Frame 7 (RSa4F7)
Bit 3: Sa4 Bit of Frame 9 (RSa4F9)
Bit 2: Sa4 Bit of Frame 11 (RSa4F11)
Bit 1: Sa4 Bit of Frame 13 (RSa4F13)
Bit 0: Sa4 Bit of Frame 15 (RSa4F15)
282 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RSa5
Register Description:
Register Address:
Received Sa5 Bits
CCh
Bit #
Name
Default
7
RSa5F1
0
6
RSa5F3
0
5
RSa5F5
0
4
RSa5F7
0
3
RSa5F9
0
2
RSa5F11
0
1
RSa5F13
0
0
RSa5F15
0
Bit 7: Sa5 Bit of Frame 1 (RSa5F1)
Bit 6: Sa5 Bit of Frame 3 (RSa5F3)
Bit 5: Sa5 Bit of Frame 5 (RSa5F5)
Bit 4: Sa5 Bit of Frame 7 (RSa5F7)
Bit 3: Sa5 Bit of Frame 9 (RSa5F9)
Bit 2: Sa5 Bit of Frame 11 (RSa5F11)
Bit 1: Sa5 Bit of Frame 13 (RSa5F13)
Bit 0: Sa5 Bit of Frame 15 (RSa5F15)
Register Name:
TR.RSa6
Register Description:
Register Address:
Received Sa6 Bits
CDh
Bit #
Name
Default
7
RSa6F1
0
6
RSa6F3
0
5
RSa6F5
0
4
RSa6F7
0
3
RSa6F9
0
2
RSa6F11
0
1
RSa6F13
0
0
RSa6F15
0
Bit 7: Sa6 Bit of Frame 3(RSa6F3)
Bit 6: Sa6 Bit of Frame 4 (RSa6F4)
Bit 5: Sa6 Bit of Frame 5 (RSa6F5)
Bit 4: Sa6 Bit of Frame 7 (RSa6F7)
Bit 3: Sa6 Bit of Frame 9 (RSa6F9)
Bit 2: Sa6 Bit of Frame 11 (RSa6F11)
Bit 1: Sa6 Bit of Frame 13 (RSa6F13)
Bit 0: Sa6 Bit of Frame 15 (RSa6F15)
283 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.RSa7
Register Description:
Register Address:
Received Sa7 Bits
CEh
Bit #
Name
Default
7
RSa7F1
0
6
Rsa7F3
0
5
RSa7F5
0
4
RSa7F7
0
3
RSa7F9
0
2
RSa7F11
0
1
RSa7F13
0
0
RSa7F15
0
Bit 7: Sa7 Bit of Frame 1(RSa4F1)
Bit 6: Sa7 Bit of Frame 3 (RSa7F3)
Bit 5: Sa7 Bit of Frame 5 (RSa7F5)
Bit 4: Sa7 Bit of Frame 7 (RSa7F7)
Bit 3: Sa7 Bit of Frame 9 (RSa7F9)
Bit 2: Sa7 Bit of Frame 11 (RSa7F11)
Bit 1: Sa7 Bit of Frame 13 (RSa7F13)
Bit 0: Sa7 Bit of Frame 15 (RSa7F15)
Register Name:
TR.RSa8
Register Description:
Register Address:
Received Sa8 Bits
CFh
Bit #
Name
Default
7
RSa8F1
0
6
RSa8F3
0
5
RSa8F5
0
4
RSa8F7
0
3
RSa8F9
0
2
RSa8F11
0
1
RSa8F13
0
0
RSa8F15
0
Bit 7: Sa8 Bit of Frame 1 (RSa8F1)
Bit 6: Sa8 Bit of Frame 3 (RSa8F3)
Bit 5: Sa8 Bit of Frame 5 (RSa8F5)
Bit 4: Sa8 Bit of Frame 7 (RSa8F7)
Bit 3: Sa8 Bit of Frame 9 (RSa8F9)
Bit 2: Sa8 Bit of Frame 11 (RSa8F11)
Bit 1: Sa8 Bit of Frame 13 (RSa8F13)
Bit 0: Sa8 Bit of Frame 15 (RSa8F15)
284 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TAF
Register Description:
Register Address:
Transmit Align Frame Register
D0h
Bit #
Name
Default
7
Si
0
6
0
0
5
0
0
4
1
1
3
1
1
2
0
0
1
1
1
0
1
1
Bit 7: International Bit (Si)
Bit 6: Frame Alignment Signal Bit (0)
Bit 5: Frame Alignment Signal Bit (0)
Bit 4: Frame Alignment Signal Bit (1)
Bit 3: Frame Alignment Signal Bit (1)
Bit 2: Frame Alignment Signal Bit (0)
Bit 1: Frame Alignment Signal Bit (1)
Bit 0: Frame Alignment Signal Bit (1)
Register Name:
TR.TNAF
Register Description:
Register Address:
Transmit Nonalign Frame Register
D1h
Bit #
Name
Default
7
Si
0
6
1
1
5
A
0
4
Sa4
0
3
Sa5
0
2
Sa6
0
1
Sa7
0
0
Sa8
0
Bit 7: International Bit (Si)
Bit 6: Frame Nonalignment Signal Bit (1)
Bit 5: Remote Alarm [used to transmit the alarm (A)]
Bit 4: Additional Bit 4 (Sa4)
Bit 3: Additional Bit 5 (Sa5)
Bit 2: Additional Bit 6 (Sa6)
Bit 1: Additional Bit 7 (Sa7)
Bit 0: Additional Bit 8 (Sa8)
285 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TSiAF
Register Description:
Register Address:
Transmit Si Bits of the Align Frame
D2h
Bit #
Name
Default
7
TSiF0
0
6
TSiF2
0
5
TSiF4
0
4
TSiF6
0
3
TSiF8
0
2
TSiF10
0
1
TSiF12
0
0
TSiF14
0
Bit 7: Si Bit of Frame 0 (TSiF0)
Bit 6: Si Bit of Frame 2 (TSiF2)
Bit 5: Si Bit of Frame 4 (TSiF4)
Bit 4: Si Bit of Frame 6 (TSiF6)
Bit 3: Si Bit of Frame 8 (TSiF8)
Bit 2: Si Bit of Frame 10 (TSiF10)
Bit 1: Si Bit of Frame 12 (TSiF12)
Bit 0: Si Bit of Frame 14 (TSiF14)
Register Name:
TR.TSiNAF
Register Description:
Register Address:
Transmit Si Bits of the Nonalign Frame
D3h
Bit #
Name
Default
7
TSiF1
0
6
TSiF3
0
5
TSiF5
0
4
TSiF7
0
3
TSiF9
0
2
TSiF11
0
1
TSiF13
0
0
TSiF15
0
Bit 7: Si Bit of Frame 1 (TSiF1)
Bit 6: Si Bit of Frame 3 (TSiF3)
Bit 5: Si Bit of Frame 5 (TSiF5)
Bit 4: Si Bit of Frame 7 (TSiF7)
Bit 3: Si Bit of Frame 9 (TSiF9)
Bit 2: Si Bit of Frame 11 (TSiF11)
Bit 1: Si Bit of Frame 13 (TSiF13)
Bit 0: Si Bit of Frame 15 (TSiF15)
286 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TRA
Register Description:
Register Address:
Transmit Remote Alarm
D4h
Bit #
Name
Default
7
TRAF1
0
6
TRAF3
0
5
TRAF5
0
4
TRAF7
0
3
TRAF9
0
2
TRAF11
0
1
TRAF13
0
0
TRAF15
0
Bit 7: Remote Alarm Bit of Frame 1 (TRAF1)
Bit 6: Remote Alarm Bit of Frame 3 (TRAF3)
Bit 5: Remote Alarm Bit of Frame 5 (TRAF5)
Bit 4: Remote Alarm Bit of Frame 7 (TRAF7)
Bit 3: Remote Alarm Bit of Frame 9 (TRAF9)
Bit 2: Remote Alarm Bit of Frame 11 (TRAF11)
Bit 1: Remote Alarm Bit of Frame 13 (TRAF13)
Bit 0: Remote Alarm Bit of Frame 15 (TRAF15)
Register Name:
TR.TSa4
Register Description:
Register Address:
Transmit Sa4 Bits
D5h
Bit #
Name
Default
7
TSa4F1
0
6
TSa4F3
0
5
TSa4F5
0
4
TSa4F7
0
3
TSa4F9
0
2
TSa4F11
0
1
TSa4F13
0
0
TSa4F15
0
Bit 7: Sa4 Bit of Frame 1 (TSa4F1)
Bit 6: Sa4 Bit of Frame 3 (TSa4F3)
Bit 5: Sa4 Bit of Frame 5 (TSa4F5)
Bit 4: Sa4 Bit of Frame 7 (TSa4F7)
Bit 3: Sa4 Bit of Frame 9 (TSa4F9)
Bit 2: Sa4 Bit of Frame 11 (TSa4F11)
Bit 1: Sa4 Bit of Frame 13 (TSa4F13)
Bit 0: Sa4 Bit of Frame 15 (TSa4F15)
287 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TSa5
Register Description:
Register Address:
Transmitted Sa5 Bits
D6h
Bit #
Name
Default
7
TSa5F1
0
6
TSa5F3
0
5
TSa5F5
0
4
TSa5F7
0
3
TSa5F9
0
2
TSa5F11
0
1
TSa5F13
0
0
TSa5F15
0
Bit 7: Sa5 Bit of Frame 1 (TSa5F1)
Bit 6: Sa5 Bit of Frame 3 (TSa5F3)
Bit 5: Sa5 Bit of Frame 5 (TSa5F5)
Bit 4: Sa5 Bit of Frame 7 (TSa5F7)
Bit 3: Sa5 Bit of Frame 9 (TSa5F9)
Bit 2: Sa5 Bit of Frame 11 (TSa5F11)
Bit 1: Sa5 Bit of Frame 13 (TSa5F13)
Bit 0: Sa5 Bit of Frame 15 (TSa5F15)
Register Name:
TR.TSa6
Register Description:
Register Address:
Transmit Sa6 Bits
D7h
Bit #
Name
Default
7
TSa6F1
0
6
TSa6F3
0
5
TSa6F5
0
4
TSa6F7
0
3
TSa6F9
0
2
TSa6F11
0
1
TSa6F13
0
0
TSa6F15
0
Bit 7: Sa6 Bit of Frame 1 (TSa6F1)
Bit 6: Sa6 Bit of Frame 3 (TSa6F3)
Bit 5: Sa6 Bit of Frame 5 (TSa6F5)
Bit 4: Sa6 Bit of Frame 7 (TSa6F7)
Bit 3: Sa6 Bit of Frame 9 (TSa6F9)
Bit 2: Sa6 Bit of Frame 11 (TSa6F11)
Bit 1: Sa6 Bit of Frame 13 (TSa6F13)
Bit 0: Sa6 Bit of Frame 15 (TSa6F15)
288 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TSa7
Register Description:
Register Address:
Transmit Sa7 Bits
D8h
Bit #
Name
Default
7
TSa7F1
0
6
TSa7F3
0
5
TSa7F5
0
4
TSa7F7
0
3
TSa7F9
0
2
TSa7F11
0
1
TSa7F13
0
0
TSa7F15
0
Bit 7: Sa7 Bit of Frame 1 (TSa4F1)
Bit 6: Sa7 Bit of Frame 3 (TSa7F3)
Bit 5: Sa7 Bit of Frame 5 (TSa7F5)
Bit 4: Sa7 Bit of Frame 7 (TSa7F7)
Bit 3: Sa7 Bit of Frame 9 (TSa7F9)
Bit 2: Sa7 Bit of Frame 11 (TSa7F11)
Bit 1: Sa7 Bit of Frame 13 (TSa7F13)
Bit 0: Sa7 Bit of Frame 15 (TSa7F15)
Register Name:
TR.TSa8
Register Description:
Register Address:
Transmit Sa8 Bits
D9h
Bit #
Name
Default
7
TSa8F1
0
6
TSa8F3
0
5
TSa8F5
0
4
TSa8F7
0
3
TSa8F9
0
2
TSa8F11
0
1
TSa8F13
0
0
TSa8F15
0
Bit 7: Sa8 Bit of Frame 1 (TSa8F1)
Bit 6: Sa8 Bit of Frame 3 (TSa8F3)
Bit 5: Sa8 Bit of Frame 5 (TSa8F5)
Bit 4: Sa8 Bit of Frame 7 (TSa8F7)
Bit 3: Sa8 Bit of Frame 9 (TSa8F9)
Bit 2: Sa8 Bit of Frame 11 (TSa8F11)
Bit 1: Sa8 Bit of Frame 13 (TSa8F13)
Bit 0: Sa8 Bit of Frame 15 (TSa8F15)
289 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.TSACR
Register Description:
Register Address:
Transmit Sa Bit Control Register
DAh
Bit #
Name
Default
7
SiAF
0
6
SiNAF
0
5
RA
0
4
Sa4
0
3
Sa5
0
2
Sa6
0
1
Sa7
0
0
Sa8
0
Bit 7: International Bit in Align Frame Insertion Control Bit (SiAF)
0 = do not insert data from the TR.TSiAF register into the transmit data stream
1 = insert data from the TR.TSiAF register into the transmit data stream
Bit 6: International Bit in Nonalign Frame Insertion Control Bit (SiNAF)
0 = do not insert data from the TR.TSiNAF register into the transmit data stream
1 = insert data from the TR.TSiNAF register into the transmit data stream
Bit 5: Remote Alarm Insertion Control Bit (RA)
0 = do not insert data from the TR.TRA register into the transmit data stream
1 = insert data from the TR.TRA register into the transmit data stream
Bit 4: Additional Bit 4 Insertion Control Bit (Sa4)
0 = do not insert data from the TR.TSa4 register into the transmit data stream
1 = insert data from the TR.TSa4 register into the transmit data stream
Bit 3: Additional Bit 5 Insertion Control Bit (Sa5)
0 = do not insert data from the TR.TSa5 register into the transmit data stream
1 = insert data from the TR.TSa5 register into the transmit data stream
Bit 2: Additional Bit 6 Insertion Control Bit (Sa6)
0 = do not insert data from the TR.TSa6 register into the transmit data stream
1 = insert data from the TR.TSa6 register into the transmit data stream
Bit 1: Additional Bit 7 Insertion Control Bit (Sa7)
0 = do not insert data from the TR.TSa7 register into the transmit data stream
1 = insert data from the TR.TSa7 register into the transmit data stream
Bit 0: Additional Bit 8 Insertion Control Bit (Sa8)
0 = do not insert data from the TR.TSa8 register into the transmit data stream
1 = insert data from the TR.TSa8 register into the transmit data stream
Register Name:
TR.BAWC
Register Description:
Register Address:
BERT Alternating Word-Count Rate
DBh
Bit #
Name
Default
7
ACNT7
0
6
ACNT6
0
5
ACNT5
0
4
ACNT4
0
3
ACNT3
0
2
ACNT2
0
1
ACNT1
0
0
ACNT0
0
Bits 0 – 7: Alternating Word-Count Rate Bits 0 to 7 (ACNT0 to ACNT7). ACNT0 is the LSB of the 8-bit
alternating word-count rate counter.
290 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.BRP1
Register Description:
Register Address:
BERT Repetitive Pattern Set Register 1
DCh
Bit #
Name
Default
7
RPAT7
0
6
RPAT6
0
5
RPAT5
0
4
RPAT4
0
3
RPAT3
0
2
RPAT2
0
1
RPAT1
0
0
RPAT0
0
Bits 0 – 7: BERT Repetitive Pattern Set Bits 0 to 7 (RPAT0 to RPAT7) RPAT0 is the LSB of the 32-bit repetitive
pattern set.
Register Name:
TR.BRP2
Register Description:
Register Address:
BERT Repetitive Pattern Set Register 2
DDh
Bit #
Name
Default
7
RPAT15
0
6
RPAT14
0
5
RPAT13
0
4
RPAT12
0
3
RPAT11
0
2
RPAT10
0
1
RPAT9
0
0
RPAT8
0
Bits 0 – 7: BERT Repetitive Pattern Set Bits 8 to 15 (RPAT8 to RPAT15)
Register Name:
TR.BRP3
Register Description:
Register Address:
BERT Repetitive Pattern Set Register 3
DEh
Bit #
Name
Default
7
RPAT23
0
6
RPAT22
0
5
RPAT21
0
4
RPAT20
0
3
RPAT19
0
2
RPAT18
0
1
RPAT17
0
0
RPAT16
0
Bits 0 – 7: BERT Repetitive Pattern Set Bits 16 to 23 (RPAT16 to RPAT23)
Register Name:
TR.BRP4
Register Description:
Register Address:
BERT Repetitive Pattern Set Register 4
DFh
Bit #
Name
Default
7
RPAT31
0
6
RPAT30
0
5
RPAT29
0
4
RPAT28
0
3
RPAT27
0
2
RPAT26
0
1
RPAT25
0
0
RPAT24
0
Bits 0 – 7: BERT Repetitive Pattern Set Bits 24 to 31 (RPAT24 to RPAT31). RPAT31 is the LSB of the 32-bit
repetitive pattern set.
291 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.BC1
Register Description:
Register Address:
BERT Control Register 1
E0h
Bit #
Name
Default
7
TC
0
6
TINV
0
5
RINV
0
4
PS2
0
3
PS1
0
2
PS0
0
1
LC
0
0
RESYNC
0
Bit 7: Transmit Pattern Load (TC). A low-to-high transition loads the pattern generator with the pattern that is to
be generated. This bit should be toggled from low to high whenever the host wishes to load a new pattern. Must be
cleared and set again for subsequent loads.
Bit 6: Transmit Invert-Data Enable (TINV)
0 = do not invert the outgoing data stream
1 = invert the outgoing data stream
Bit 5: Receive Invert-Data Enable (RINV)
0 = do not invert the incoming data stream
1 = invert the incoming data stream
Bits 2 – 4: Pattern Select Bits (PS0 to PS2)
PS
PS1 PS0
Pattern Definition
2
0
0
0
0
0
1
0
1
0
Pseudorandom 2E7 - 1
Pseudorandom 2E11 - 1
Pseudorandom 2E15 - 1
Pseudorandom pattern QRSS. A 220 - 1 pattern with 14 consecutive zero
restrictions.
0
1
1
1
1
0
0
0
1
Repetitive pattern
Alternating word pattern
Modified 55 octet (Daly) pattern. The Daly pattern is a repeating 55 octet
pattern that is byte-aligned into the active DS0 time slots. The pattern is
defined in an ATIS (Alliance for Telecommunications Industry Solutions)
Committee T1 Technical Report Number 25 (November 1993).
Pseudorandom 2E9 – 1
1
1
1
1
0
1
Bit 1: Load Bit and Error Counters (LC). A low-to-high transition latches the current bit and error counts into
registers TR.BBC1/ TR.BBC2/ TR.BBC3/ TR.BBC4 and TR.BEC1/ TR.BEC2/ TR.BEC3 and clears the internal
count. This bit should be toggled from low to high whenever the host wishes to begin a new acquisition period.
Must be cleared and set again for subsequent loads.
Bit 0: Force Resynchronization (RESYNC). A low-to-high transition forces the receive BERT synchronizer to
resynchronize to the incoming data stream. This bit should be toggled from low to high whenever the host wishes
to acquire synchronization on a new pattern. Must be cleared and set again for a subsequent resynchronization.
292 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.BC2
Register Description:
Register Address:
BERT Control Register 2
E1h
Bit #
Name
Default
7
EIB2
0
6
EIB1
0
5
EIB0
0
4
SBE
0
3
RPL3
0
2
RPL2
0
1
RPL1
0
0
RPL0
0
Bits 5 – 7: Error Insert Bits 0 to 2 (EIB0 to EIB2). Automatically inserts bit errors at the prescribed rate into the
generated data pattern. Can be used for verifying error-detection features.
EIB2
EIB1
EIB0
Error Rate Inserted
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
No errors automatically inserted
10E-1
10E-2
10E-3
10E-4
10E-5
10E-6
10E-7
Bit 4: Single Bit-Error Insert (SBE). A low-to-high transition creates a single-bit error. Must be cleared and set
again for a subsequent bit error to be inserted.
Bits 0 – 3: Repetitive Pattern Length Bit 3 (RPL0 to RPL3). RPL0 is the LSB and RPL3 is the MSB of a nibble
that describes how long the repetitive pattern is. The valid range is 17 (0000) to 32 (1111). These bits are ignored if
the receive BERT is programmed for a pseudorandom pattern. To create repetitive patterns fewer than 17 bits in
length, the user must set the length to an integer number of the desired length that is less than or equal to 32. For
example, to create a 6-bit pattern, the user can set the length to 18 (0001) or to 24 (0111) or to 30 (1101).
Length
RPL3
RPL2
RPL1
RPL0
(bits)
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
293 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.BBC1
Register Description:
Register Address:
BERT Bit Count Register 1
E3h
Bit #
Name
Default
7
BBC7
0
6
BBC6
0
5
BBC5
0
4
BBC4
0
3
BBC3
0
2
BBC2
0
1
BBC1
0
0
BBC0
0
Bits 0 – 7: BERT Bit Counter Bits 0 to 7 (BBC0 to BBC7). BBC0 is the LSB of the 32-bit counter.
Register Name:
TR.BBC2
Register Description:
Register Address:
BERT Bit Count Register 2
E4h
Bit #
Name
Default
7
BBC15
0
6
BBC14
0
5
BBC13
0
4
BBC12
0
3
BBC11
0
2
BBC10
0
1
BBC9
0
0
BBC8
0
Bits 0 – 7: BERT Bit Counter Bits 8 to 15 (BBC8 to BBC15)
Register Name:
TR.BBC3
Register Description:
Register Address:
BERT Bit Count Register 3
E5h
Bit #
Name
Default
7
BBC23
0
6
BBC22
0
5
BBC21
0
4
BBC20
0
3
BBC19
0
2
BBC18
0
1
BBC17
0
0
BBC16
0
Bits 0 – 7: BERT Bit Counter Bits 16 to 23 (BBC16 to BBC23)
Register Name:
TR.BBC4
Register Description:
Register Address:
BERT Bit Count Register 4
E6h
Bit #
Name
Default
7
BBC31
0
6
BBC30
0
5
BBC29
0
4
BBC28
0
3
BBC27
0
2
BBC26
0
1
BBC25
0
0
BBC24
0
Bits 0 – 7: BERT Bit Counter Bits 24 to 31 (BBC24 to BBC31). BBC31 is the MSB of the 32-bit counter.
294 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.BEC1
Register Description:
Register Address:
BERT Error-Count Register 1
E7h
Bit #
Name
Default
7
EC7
0
6
EC6
0
5
EC5
0
4
EC4
0
3
EC3
0
2
EC2
0
1
EC1
0
0
EC0
0
Bits 0 – 7: Error Counter Bits 0 to 7 (EC0 to EC7). EC0 is the LSB of the 24-bit counter.
Register Name:
TR.BEC2
Register Description:
Register Address:
BERT Error-Count Register 2
E8h
Bit #
Name
Default
7
EC15
0
6
EC14
0
5
EC13
0
4
EC12
0
3
EC11
0
2
EC10
0
1
EC9
0
0
EC8
0
Bits 0 – 7: Error Counter Bits 8 to 15 (EC8 to EC15)
Register Name:
TR.BEC3
Register Description:
Register Address:
BERT Error-Count Register 3
E9h
Bit #
Name
Default
7
EC23
0
6
EC22
0
5
EC21
0
4
EC20
0
3
EC19
0
2
EC18
0
1
EC17
0
0
EC16
0
Bits 0 – 7: Error Counter Bits 16 to 23 (EC16 to EC23). EC0 is the MSB of the 24-bit counter.
295 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.BIC
Register Description:
Register Address:
BERT Interface Control Register
EAh
Bit #
Name
Default
7
—
0
6
RFUS
0
5
—
0
4
TBAT
0
3
TFUS
0
2
—
0
1
BERTDIR
0
0
BERTEN
0
Bit 6: Receive Framed/Unframed Select (RFUS)
0 = BERT is not sent data from the F-bit position (framed)
1 = BERT is sent data from the F-bit position (unframed)
Bit 4: Transmit Byte-Align Toggle (TBAT). A 0-to-1 transition forces the BERT to byte align its pattern with the
transmit formatter. This bit must be transitioned in order to byte align the Daly pattern.
Bit 3: Transmit Framed/Unframed Select (TFUS)
0 = BERT does not source data into the F-bit position (framed)
1 = BERT does source data into the F-bit position (unframed)
Bit 1: BERT Direction (BERTDIR)
0 = network
BERT transmits toward the network (TTIP and TRING) and receives from the network (RTIP and RRING). The
BERT pattern can be looped back to the receiver internally by using the framer loopback function.
1 = system
BERT transmits toward the system backplane (RSERO) and receives from the system backplane (TSERI).
Bit 0: BERT Enable (BERTEN)
0 = BERT disabled
1 = BERT enabled
296 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.ERC
Register Description:
Register Address:
Error-Rate Control Register
EBh
Bit #
Name
Default
7
WNOE
0
6
—
0
5
—
0
4
CE
0
3
ER3
0
2
ER2
0
1
ER1
0
0
ER0
0
Bit 7: Write NOE Registers (WNOE). If the host wishes to update to the TR.NOEx registers, this bit must be
toggled from a 0 to a 1 after the host has already loaded the prescribed error count into the TR.NOEx registers.
The toggling of this bit causes the error count loaded into the TR.NOEx registers to be loaded into the error-
insertion circuitry on the next clock cycle. Subsequent updates require that the WNOE bit be set to 0 and then 1
once again.
Bit 4: Constant Errors (CE). When this bit is set high (and the ER0 to ER3 bits are not set to 0000), the error-
insertion logic ignores the number-of-error registers (TR.NOE1, TR.NOE2) and generates errors constantly at the
selected insertion rate. When CE is set to 0, the TR.NOEx registers determine how many errors are to be inserted.
Bits 0 – 3: Error-Insertion Rate Select Bits (ER0 to ER3)
ER3
0
0
ER2
0
0
ER1
0
0
ER0
0
1
Error Rate
No errors inserted
1 in 16
0
0
1
0
1 in 32
0
0
1
1
1 in 64
0
1
0
0
1 in 128
0
1
0
1
1 in 256
0
1
1
0
1 in 512
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1 in 1024
1 in 2048
1 in 4096
1 in 8192
1 in 16,384
1 in 32,768
1 in 65,536
1 in 131,072
1 in 262,144
1
1
1
1
297 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Register Name:
TR.NOE1
Register Description:
Register Address:
Number-of-Errors 1
ECh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Bits 0 – 7: Number-of-Errors Counter Bits 0 to 7 (C0 to C7). Bit C0 is the LSB of the 10-bit counter.
Register Name:
TR.NOE2
Register Description:
Register Address:
Number-of-Errors 2
EDh
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
—
0
2
—
0
1
C9
0
0
C8
0
Bits 0 – 1: Number-of-Errors Counter Bits 8 to 9 (C8 to C9). Bit C9 is the MSB of the 10-bit counter.
298 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
11.7.1 Number-of-Errors Left Register
The host can read the TR.NOELx registers at any time to determine how many errors are left to be inserted.
Register Name:
TR.NOEL1
Register Description:
Register Address:
Number-of-Errors Left 1
EEh
Bit #
Name
Default
7
C7
0
6
C6
0
5
C5
0
4
C4
0
3
C3
0
2
C2
0
1
C1
0
0
C0
0
Bits 0 – 7: Number-of-Errors Left Counter Bits 0 to 7 (C0 to C7). Bit C0 is the LSB of the 10-bit counter.
Register Name:
TR.NOEL2
Register Description:
Register Address:
Number-of-Errors Left 2
EFh
Bit #
Name
Default
7
—
0
6
—
0
5
—
0
4
—
0
3
—
0
2
—
0
1
C9
0
0
C8
0
Bits 0 – 1: Number-of-Errors Left Counter Bits 8 to 9 (C8 to C9). Bit C9 is the MSB of the 10-bit counter.
299 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
12 FUNCTIONAL TIMING
12.1 Functional Serial I/O Timing
The Serial Interface provides flexible timing to interconnect with a wide variety of serial interfaces. TDEN is an
input signal that can be used to enable or block the TSERO data. The “shaded bits” are not clocked by the
DS33R11. The TDEN must occur one bit before the effected bit in the TSERO stream. Note that polarity of the
TDEN is selectable through LI.TSLCR. In the figure below, TDEN is active low, allowing the bits to clock and
inactive high, causing the next data bit not be clocked. TCLKE can be gapped as shown in the following figure.
Similarly, the receiver function is governed by RCLKI, RDEN and RSERI. RSERI data will not be provided to the
receiver for the bits blocked when RDEN is inactive. The RDEN polarity can be programmed by LI.RSLCR. The
RDEN signal must be coincident with the RSERI bit that needs to be blocked.
Figure 12-1. Tx Serial Interface Functional Timing
TCLKE
TDEN
TSERO
TCLKE Gapped
TSERO
Figure 12-2. Rx Serial Interface Functional Timing
RCLKI
RDEN
RSERI
RCLKI Gapped
RSERI
300 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
The DS33R11 provides the TBSYNC signal as a byte boundary indication to an external interface when X.86
(LAPS) functionality is selected. The functional timing of TBSYNC is shown in the following figure.TBSYNC is
active high on the last bit of the byte being shifted out, and occurs every 8 bits. For the serial receiver interface,
RBSYNC is used to provide byte boundary indication to the DS33R11 when X.86 (LAPS) mode is used. The
functional timing is shown in Figure 12-3. In X.86 Mode, the receiver expects the RBSYNC byte indicator as shown
Figure 12-3. Transmit Byte Sync Functional Timing
TCLKE
TBYSYNC
last bit
1st bit
TSERO
Figure 12-4. Receive Byte Sync Functional Timing
RCLKI
RBYSYNC
last bit
1st bit
RSERI
12.2 MII and RMII Interfaces
The MII Interface Transmit Port has its own TX_CLK and data interface. The data TXD [3:0] operates
synchronously with TX_CLK. The LSB is presented first. TX_CLK should be 2.5MHz for 10Mbit/s operation and
25MHz for 100Mbit/s operation. TX_EN is valid at the same time as the first byte of the preamble. In DTE Mode
TX_CLK is input from the external PHY. In DCE Mode, the DS33R11 provides TX_CLK, derived from an external
reference (SYSCLKI).
Figure 12-5. MII Transmit Functional Timing
TX_CLK
F
C
S
P
R
E
A
E
M
B
L
E
TXD[3:0]
TX_EN
301 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
In Half-Duplex (DTE) Mode, the DS33R11 supports CRS and COL signals. CRS is active when the PHY detects
transmit or receive activity. If there is a collision as indicated by the COL input, the DS33R11 will replace the data
nibbles with jam nibbles. After a “random“ time interval, the packet is retransmitted. The MAC will try to send the
packet a maximum of 16 times. The jam sequence consists of 55555555h. Note that the COL signal and CRS can
be asynchronous to the TX_CLK and are only valid in half duplex mode.
Figure 12-6. MII Transmit Half Duplex with a Collision Functional Timing
TX_CLK
P
R
E
A
M
B
L
E
J
J
J
J
J
J
J
J
TXD[3:0]
TX_EN
CRS
COL
Receive Data (RXD[3:0]) is clocked from the external PHY synchronously with RX_CLK. The RX_CLK signal is
2.5MHz for 10Mbit/s operation and 25MHz for 100Mbit/s operation. RX_DV is asserted by the PHY from the first
nibble of the preamble in 100 Mbit/s operation or first nibble of SFD for 10 Mbit/s operation. The data on RXD[3:0]
is not accepted by the MAC if RX_DV is low or RX_ERR is high (in DTE mode). RX_ERR should be tied low when
in DCE Mode.
Figure 12-7. MII Receive Functional Timing
RX_CLK
F
C
S
P
R
E
A
E
M
B
L
E
RXD[3:0]
In RMII Mode, TX_EN is high with the first bit of the preamble. The TXD[1:0] is synchronous with the 50MHz
REF_CLK. For 10 Mbit/s operation, the data bit outputs are updated every 10 clocks.
Figure 12-8. RMII Transmit Interface Functional Timing
REFCLK
P
R
E
A
M
B
L
E
F
C
S
TXD[1:0]
TX_EN
302 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
RMII Receive data on RXD[1:0] is expected to be synchronous with the rising edge of the 50 MHz REF_CLK. The
data is only valid if CRS_DV is high. The external PHY asynchronously drives CRS_DV low during carrier loss.
Figure 12-9. RMII Receive Interface Functional Timing
REFCLK
P
R
E
A
M
B
L
E
F
C
S
RXD[1:0]
CRS_DV
12.3 Transceiver T1 Mode Functional Timing
Figure 12-10. Receive-Side D4 Timing
1
FRAME#
RFSYNC
RSYNC1
RSYNC 2
RSYNC3
2
3
4
5
6
7
8
9
10 11 12
1
2
3
4
5
NOTE 1: RSYNC IN THE FRAME MODE (TR.IOCR1.5 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.6 = 0).
NOTE 2: RSYNC IN THE FRAME MODE (TR.IOCR1.5 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.6 = 1).
NOTE 3: RSYNC IN THE MULTIFRAME MODE (TR.IOCR1.5 = 1).
Figure 12-11. Receive-Side ESF Timing
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
FRAME#
RSYNC1
RFSYNC
RSYNC2
RSYNC3
NOTE 1: RSYNC IN FRAME MODE (TR.IOCR1.4 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.6 = 0).
NOTE 2: RSYNC IN FRAME MODE (TR.IOCR1.4 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.6 = 1).
NOTE 3: RSYNC IN MULTIFRAME MODE (TR.IOCR1.4 = 1).
303 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-12. Receive-Side Boundary Timing (Elastic Store Disabled)
RCLKO
CHANNEL 23
CHANNEL 24
CHANNEL 1
MSB
LSB
LSB MSB
F
RSERO
RSYNC
RFSYNC
CHANNEL 23
C/A
CHANNEL 24
C/A
CHANNEL 1
A
A
B
A
B
D/B
D/B
RSIG
RCHCLK
1
RCHBLK
NOTE 1: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
Figure 12-13. Receive-Side 1.544MHz Boundary Timing (Elastic Store Enabled)
RSYSCLK
CHANNEL 23
CHANNEL 24
CHANNEL 1
MSB
LSB
LSB MSB
F
RSERO
RSYNC1
RMSYNC
RSYNC2
CHANNEL 1
CHANNEL 23
C/A
CHANNEL 24
C/A
A
A
B
A
B
D/B
D/B
RSIG
RCHCLK
RCHBLK 3
NOTE 1: RSYNC IS IN THE OUTPUT MODE (TR.IOCR1.4 = 0).
NOTE 2: RSYNC IS IN THE INPUT MODE (TR.IOCR1.4 = 1).
NOTE 3: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
304 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-14. Receive-Side 2.048MHz Boundary Timing (Elastic Store Enabled)
RSYSCLK
CHANNEL 31
CHANNEL 32
CHANNEL 1
RSER O1
5
LSB
F
LSB MSB
2
RSYNC
RMSYNC
3
RSYNC
CHANNEL 1
CHANNEL 32
CHANNEL 31
C/A
C/A
A
B
A
B
D/B
D/B
RSIG
RCHCLK
RCHBLK4
NOTE 1: RSERO DATA IN CHANNELS 1, 5, 9, 13, 17, 21, 25, AND 29 ARE FORCED TO 1.
NOTE 2: RSYNC IS IN THE OUTPUT MODE (TR.IOCR1.4 = 0).
NOTE 3: RSYNC IS IN THE INPUT MODE (TR.IOCR1.4 = 1).
NOTE 4: RCHBLK IS FORCED TO 1 IN THE SAME CHANNELS AS RSERO (SEE NOTE 1).
NOTE 5: THE F-BIT POSITION IS PASSED THROUGH THE RECEIVE-SIDE ELASTIC STORE.
Figure 12-15. Transmit-Side D4 Timing
FRAME#
1
2
3
4
5
6
7
8
9
10 11 12
1
2
3
4
5
TSYNC1
TSSYNC
TSYNC2
TSYNC3
NOTE 1: TSYNC IN THE FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.1 = 0).
NOTE 2: TSYNC IN THE FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.1 = 1).
NOTE 3: TSYNC IN THE MULTIFRAME MODE (TR.IOCR1.2 = 1).
305 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-16. Transmit-Side ESF Timing
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
FRAME#
TSYNC1
TSSYNC
TSYNC2
TSYNC3
NOTE 1: TSYNC IN FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS NOT ENABLED (TR.IOCR1.3 = 0).
NOTE 2: TSYNC IN FRAME MODE (TR.IOCR1.2 = 0) AND DOUBLE-WIDE FRAME SYNC IS ENABLED (TR.IOCR1.3 = 1).
NOTE 3: TSYNC IN MULTIFRAME MODE (TR.IOCR1.2 = 1).
Figure 12-17. Transmit-Side Boundary Timing (with Elastic Store Disabled)
TCLKT
CHANNEL 1
CHANNEL 2
LSB
F
MSB
LSB MSB
LSB MSB
TSERI
TSYNC1
TSYNC2
CHANNEL 1
CHANNEL 2
D/B
A
B
C/A D/B
A
B
C/A D/B
TSIG
TCHCLK
TCHBLK3
NOTE 1: TSYNC IS IN THE OUTPUT MODE (TR.IOCR1.1 = 1).
NOTE 2: TSYNC IS IN THE INPUT MODE (TR.IOCR1.1 = 0).
NOTE 3: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 2.
306 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-18. Transmit-Side 1.544MHz Boundary Timing (Elastic Store Enabled)
TSYSCLK
CHANNEL 23
CHANNEL 24
CHANNEL 1
LSB MSB
LSB
F
MSB
TSERI
TSSYNC
CHANNEL 23
CHANNEL 24
CHANNEL 1
A
A
B
C/A D/B
A
B
C/A D/B
TSIG
TCHCLK
TCHBLK1
NOTE 1: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24 (IF THE TPCSI BIT IS SET, THEN THE SIGNALING DATA AT TSIG IS
IGNORED DURING CHANNEL 24).
Figure 12-19. Transmit-Side 2.048MHz Boundary Timing (Elastic Store Enabled)
TSYSCLK
CHANNEL 31
CHANNEL 32
CHANNEL 1
CHANNEL 1
F4
TSERI 1
TSSYNC
LSB MSB
LSB
CHANNEL 31
CHANNEL 32
A
B
C/A D/B
A
B
C/A D/B
A
TSIG
TCHCLK
TCHBLK2,3
NOTE 1: TSERI DATA IN CHANNELS 1, 5, 9, 13, 17, 21, 25, AND 29 IS IGNORED.
NOTE 2: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 31 (IF THE TPCSI BIT IS SET, THEN THE SIGNALING DATA AT TSIG WILL BE
IGNORED).
NOTE 3: TCHBLK IS FORCED TO 1 IN THE SAME CHANNELS AS TSERI IS IGNORED (SEE NOTE 1).
NOTE 4: THE F-BIT POSITION FOR THE T1 FRAME IS SAMPLED AND PASSED THROUGH THE TRANSMIT-SIDE ELASTIC STORE INTO THE MSB
BIT POSITION OF CHANNEL 1. (NORMALLY, THE TRANSMIT-SIDE FORMATTER OVERWRITES THE F-BIT POSITION UNLESS THE FORMATTER
IS PROGRAMMED TO PASS THROUGH THE F-BIT POSITION.)
307 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
12.4 E1 Mode
Figure 12-20. Receive-Side Timing
1
FRAME#
RFSYNC
RSYNC 1
RSYNC2
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
1
NOTE 1: RSYNC IN FRAME MODE (TR.IOCR1.5 = 0).
NOTE 2: RSYNC IN MULTIFRAME MODE (TR.IOCR1.5 = 1).
NOTE 3: THIS DIAGRAM ASSUMES THE CAS MF BEGINS IN THE RAF FRAME.
Figure 12-21. Receive-Side Boundary Timing (with Elastic Store Disabled)
RCLKO
CHANNEL 32
CHANNEL 1
CHANNEL 2
MSB
LSB Si
1
A
Sa4 Sa5 Sa6 Sa7 Sa8
RSERO
RSYNC
RFSYNC
CHANNEL 32
CHANNEL 1
CHANNEL 2
C
D
A
A
B
B
RSIG
RCHCLK
RCHBLK1
Note 4
NOTE 1: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 1.
NOTE 2: SHOWN IS A RNAF FRAME BOUNDARY.
NOTE 3: RSIG NORMALLY CONTAINS THE CAS MULTIFRAME ALIGNMENT NIBBLE (0000) IN CHANNEL 1.
308 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-22. Receive-Side Boundary Timing, RSYSCLK = 1.544MHz (E-Store Enabled)
RSYSCLK
CHANNEL 23/31
LSB MSB
CHANNEL 24/32
CHANNEL 1/2
RSERO1
RSYNC2
RMSYNC
RSYNC3
MSB
LSB
F
RCHCLK
RCHBLK 4
NOTE 1: DATA FROM THE E1 CHANNELS 1, 5, 9, 13, 17, 21, 25, AND 29 IS DROPPED (CHANNEL 2 FROM THE E1 LINK IS
MAPPED TO CHANNEL 1 OF THE T1 LINK, ETC.) AND THE F-BIT POSITION IS ADDED (FORCED TO ON 1).
NOTE 2: RSYNC IN THE OUTPUT MODE (TR.IOCR1.4 = 0).
NOTE 3: RSYNC IN THE INPUT MODE (TR.IOCR1.4 = 1).
NOTE 4: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
Figure 12-23. Receive-Side Boundary Timing, RSYSCLK = 2.048MHz (E-Store Enabled)
RSYSCLK
CHANNEL 31
CHANNEL 32
CHANNEL 1
LSB MSB
MSB
LSB
RSERO
RSYNC1
RMSYNC
2
RSYNC
CHANNEL 1
CHANNEL 32
CHANNEL 31
C
C
A
B
A
B
D
D
RSIG
RCHCLK
RCHBLK3
Note 4
NOTE 1: RSYNC IS IN THE OUTPUT MODE (TR.IOCR1.4 = 0).
NOTE 2: RSYNC IS IN THE INPUT MODE (TR.IOCR1.4 = 1).
NOTE 3: RCHBLK IS PROGRAMMED TO BLOCK CHANNEL 1.
NOTE 4: RSIG NORMALLY CONTAINS THE CAS MULTIFRAME ALIGNMENT NIBBLE (0000) IN CHANNEL 1.
309 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-24. G.802 Timing, E1 Mode Only
31 32 0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 0
1
2
TS #
RSYNC
TSYNC
RCHCLK
TCHCLK
RCHBLK
TCHBLK
RCLKO / RSYSCLK
TCLKT / TSYSCLK
CHANNEL 25
CHANNEL 26
NOTE: RCHBLK OR TCHBLK PROGRAMMED TO
PULSE HIGH DURING TIME SLOTS 1 THROUGH 15,
17 THROUGH 25, AND BIT 1 OF TIME SLOT 26.
MSB
LSB
RSERO / TSERI
RCHCLK / TCHCLK
RCHBLK / TCHBLK
Figure 12-25. Transmit-Side Timing
1
2
3
4
5
6
7
8
9
10 11 12 13
1
2
3
4
5
6
7
8
9
10
FRAME# 14 15 16
14 15 16
TSYNC1
TSSYNC
TSYNC2
NOTE 1: TSYNC IN FRAME MODE (TR.IOCR1.2 = 0).
NOTE 2: TSYNC IN MULTIFRAME MODE (TR.IOCR1.2 = 1).
NOTE 3: THIS DIAGRAM ASSUMES BOTH THE CAS MF AND THE CRC4 MF BEGIN WITH THE TAF FRAME.
310 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-26. Transmit-Side Boundary Timing (Elastic Store Disabled)
TCLKT
CHANNEL 1
CHANNEL 2
LSB
MSB
LSB MSB
Si
1
A
Sa4 Sa5 Sa6 Sa7 Sa8
TSERI
TSYNC1
TSYNC2
CHANNEL 1
CHANNEL 2
D
A
B
C
D
TSIG
TCHCLK
TCHBLK3
NOTE 1: TSYNC IS IN THE OUTPUT MODE (TR.IOCR1.1 = 1).
NOTE 2: TSYNC IS IN THE INPUT MODE (TR.IOCR1.1 = 0).
NOTE 3: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 2.
NOTE 5: THE SIGNALING DATA AT TSIG DURING CHANNEL 1 IS NORMALLY OVERWRITTEN IN THE TRANSMIT FORMATTER
WITH THE CAS MF ALIGNMENT NIBBLE (0000).
NOTE 6: SHOWN IS A TNAF FRAME BOUNDARY.
Figure 12-27. Transmit-Side Boundary Timing, TSYSCLK = 1.544MHz (Elastic Store
Enabled)
TSYSCLK
CHANNEL 23
CHANNEL 24
CHANNEL 1
TSERI1
LSB MSB
LSB
F
MSB
TSSYNC
TCHCLK
TCHBLK2
NOTE 1: THE F-BIT POSITION IN THE TSERI DATA IS IGNORED.
NOTE 2: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 24.
311 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 12-28. Transmit-Side Boundary Timing, TSYSCLK = 2.048MHz (Elastic Store
Enabled)
TSYSCLK
CHANNEL 31
CHANNEL 32
CHANNEL 1
CHANNEL 1
TSERI1
F4
LSB MSB
LSB
TSSYNC
CHANNEL 31
CHANNEL 32
A
B
C
D
A
B
C
D
A
TSIG
TCHCLK
TCHBLK
NOTE 1: TCHBLK IS PROGRAMMED TO BLOCK CHANNEL 31.
312 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13 OPERATING PARAMETERS
ABSOLUTE MAXIMUM RATINGS
Voltage Range on Any Lead with Respect to VSS (except VDD)….………………………………………..-0.5V to +5.5V
Supply Voltage (VDD3.3) Range with Respect to VSS……………..……………………………………….-0.3V to +3.6V
Supply Voltage (VDD1.8) with Respect to VSS………………………..…….……………………………….-0.3V to +2.0V
Ambient Operating Temperature Range………………………………...………………………………......-40°C to +85°C
Junction Operating Temperature Range…………………………………...………………………………-40°C to +125°C
Storage Temperature Range……………………………………………………………………………..…-55°C to +125°C
Soldering Temperature………………………………………………………....See IPC/JEDEC J-STD-020 Specification
These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operation
sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time can affect reliability.
Ambient Operating Temperature Range is assuming the device is mounted on a JEDEC standard test board in a convection cooled JEDEC test
enclosure.
Note: The “typ” values listed below are not production tested.
Table 13-1. Recommended DC Operating Conditions
(VDD3.3 = 3.3V ±5%, VDD1.8 = 1.8V ±5%, Tj = -40°C to +85°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Logic 1
Logic 0
VIH
2.35
-0.3
3.465
+0.75
3.465
1.89
V
V
V
V
VIL
Supply (VDD3.3) ±5%
Supply (VDD1.8) ±5%
VDD3.3
VDD1.8
3.135
1.71
3.300
1.8
Table 13-2. DC Electrical Characteristics
(VDD3.3 = 3.3V ±5%, VDD1.8 = 1.8V ±5%, Tj = -40°C to +85°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
I/O Supply Current
(VDD3.3 = 3.465V)
IDDIO
(Notes 1, 2)
100
mA
Core Supply Current
(VDD1.8 = 1.89V)
IDDCORE
(Notes 1, 2)
(Note 3)
30
7
mA
pF
μA
μA
Lead Capacitance
CIO
IIL
-10
-50
+10
-10
Input Leakage
IILP
ILO
Output Leakage (when High-Z)
(IOH = -4.0mA)
-10
+10
VOH
VOL
VOH
VOL
VIL
All outputs
All outputs
REF_CLKO
TSERO
2.35
(IOL = +4.0mA)
Output Voltage
0.75
V
V
(IOH = -8.0mA)
2.35
2.35
(IOL = +12.0mA)
0.75
0.75
Input Voltage
VIH
Typical power consumption is approximately 400mW.
Note 1:
Note 2:
Note 3:
All outputs loaded with rated capacitance; all inputs between VDD and VSS; inputs with pullups connected to VDD
Value guaranteed by design (GBD).
.
313 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.1 Thermal Characteristics
Table 13-3. Thermal Characteristics
PARAMETER
MIN
-40°C
TYP
MAX
+85°C
+125°C
Ambient Temperature (Note 1)
Junction Temperature (Note 2)
Theta-JA (θJA) in Still Air for 256-Pin
27mm BGA (Notes 2, 3)
+20.3°C/W
The package is mounted on a four-layer JEDEC standard test board.
Value guaranteed by design (GBD).
Note 1:
Note 2:
Note 3:
Theta-JA (θJA) is the junction to ambient thermal resistance, when the package is mounted on a four-layer JEDEC
standard test board.
Table 13-4. Theta-JA vs. Airflow
THETA-JA
256-PIN (27mm) BGA
20.3°C/W
AIR FLOW
0m/s (Note 1)
1m/s (Note 1)
2.5m/s (Note 1)
17.9°C/W
16.9°C/W
Value guaranteed by design (GBD).
Note 1:
314 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.2 MII Interface
Table 13-5. Transmit MII Interface
10Mbps
TYP
100Mbps
TYP
PARAMETER
TX_CLK Period
SYMBOL
UNITS
ns
MIN
MAX
MIN
MAX
t1
t2
t3
t4
400
40
TX_CLK Low Time
140
140
0
260
260
20
14
14
0
26
26
20
ns
TX_CLK High Time
ns
TX_CLK to TXD, TX_EN Delay
ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-1. Transmit MII Interface Timing
t1
t2
TX_CLK
t3
t4
t4
TXD[3:0]
TX_EN
315 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 13-6. Receive MII Interface
10Mbps
TYP
100Mbps
TYP
PARAMETER
RX_CLK Period
SYMBOL
UNITS
ns
MIN
MAX
MIN
MAX
t5
t6
t7
t8
t9
400
40
RX_CLK Low Time
RX_CLK High Time
140
140
5
260
260
14
14
5
26
26
ns
ns
RXD, RX_DV to RX_CLK Setup
Time
RX_CLK to RXD, RX_DV Hold
Time
ns
5
5
ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-2. Receive MII Interface Timing
t5
t7
RX_CLK
t6
t8
t8
t9
RXD[3:0]
RX_DV
t9
316 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.3 RMII Interface
Table 13-7. Transmit RMII Interface
10Mbps
TYP
50MHz
±50ppm
100Mbps
TYP
50MHz
±50ppm
PARAMETER
REF_CLK Frequency
REF_CLK Period
SYMBOL
UNITS
MIN
MAX
MIN
MAX
t1
t2
t3
t4
20
20
ns
ns
ns
ns
REF_CLK Low Time
7
7
5
13
13
10
7
7
5
13
13
10
REF_CLK High Time
REF_CLK to TXD, TX_EN Delay
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-3. Transmit RMII Interface Timing
t1
t2
REF_CLK
t3
t4
t4
TXD[1:0]
TX_EN
317 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 13-8. Receive RMII Interface
10Mbps
TYP
100Mbps
TYP
PARAMETER
SYMBOL
UNITS
MIN
MAX MIN
MAX
50MHz
±50ppm
50MHz
±50ppm
REF_CLK Frequency
MHz
REF_CLK Period
t1
t2
t3
t8
t9
20
20
ns
ns
ns
ns
ns
REF_CLK Low Time
REF_CLK High Time
7
7
5
5
13
13
7
7
5
5
13
13
RXD, CRS_DV to REF_CLK Setup
Time
REF_CLK to RXD, CRS_DV Hold
Time
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-4. Receive RMII Interface Timing
t5
t7
REF_CLK
t6
t8
t8
t9
RXD[3:0]
CRS_DV
t9
318 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.4 MDIO Interface
Table 13-9. MDIO Interface
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
MDC Frequency
MDC Period
1.67
600
300
300
MHz
ns
t1
t2
t3
t4
t5
t6
540
270
270
20
660
330
330
10
MDC Low Time
ns
MDC High Time
MDC to MDIO Output Delay
MDIO Setup Time
MDIO Hold Time
ns
ns
10
ns
20
ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-5. MDIO Interface Timing
t1
t2
MDC
t3
t4
MDIO
MDC
t6
t5
MDIO
319 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.5 Transmit WAN Interface
Table 13-10. Transmit WAN Interface
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
MHz
ns
TCLKE Frequency
52
TCLKE Period
t1
t2
t3
t4
t5
t6
t7
19.2
8
TCLKE Low Time
ns
TCLKE High Time
8
ns
TCLKE to TSERO Output Delay
TCLKE to TBSYNC Setup Time
TBSYNC Hold Time
3
10
ns
3.5
7
ns
ns
TCLKE to TDEN Output Delay
3.5
ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-6. Transmit WAN Interface Timing
t1
t2
TCLKE
t3
t4
TSERO
t7
TDEN
t5
TBSYNC
t6
320 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.6 Receive WAN Interface
Table 13-11. Receive WAN Interface
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
RCLKI Frequency
RCLKI Period
52
MHz
t1
t2
t3
t4
t4
t4
t4
t4
t5
t5
t5
t5
19.2
8
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
RCLKI Low Time
RCLKI High Time
RSERI Setup Time
RDEN Setup Time
RBSYNC Setup Time
RDEN Setup Time
RBSYNC Setup Time
RSERI Hold Time
RBSYNC Hold Time
RDEN Hold Time
RBSYNC Hold Time
8
7
7
7
7
7
2
2
2
2
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-7. Receive WAN Interface Timing
t1
t2
RCLKI
t3
t4
t5
RSERI
t4
t5
RDEN
t5
t4
RBSYNC
321 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.7 SDRAM Timing
Table 13-12. SDRAM Interface Timing
100 MHz
PARAMETER
SYMBOL
UNITS
ns
MIN
TYP
MAX
SDCLKO Period
t1
t2
9.7
10
10.3
SDCLKO Duty Cycle
4
6
7
ns
SDCLKO to SDATA Valid
Write to SDRAM
t3
t4
t5
t6
t7
t8
t9
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SDCLKO to SDATA Drive On
Write to SDRAM
4
3
SDCLKO to SDATA Invalid
Write to SDRAM
SDCLKO to SDATA Drive Off
Write to SDRAM
4
SDATA to SDCLKO Setup Time
Read from SDRAM
2
SDCLKO to SDATA Hold Time
Read from SDRAM
2
5
SDCLKO to SRAS, SCAS, SWE, SDCS Active
Read or Write to SDRAM
SDCLKO TO SRAS, SCAS, SWE, SDCS Inactive
Read or Write to SDRAM
t10
t11
t12
t13
t14
2
2
SDCLKO to SDA, SBA Valid
Read or Write to SDRAM
SDCLKO TO SDA, SBA Invalid
Read or write to SDRAM
7
5
SDCLKO to SDMASK Valid
Read or write to SDRAM
SDCLKO TO SDMASK Invalid
Read or write to SDRAM
2
Note 1: Timing parameters in this table are guaranteed by design (GBD).
322 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-8. SDRAM Interface Timing
t1
SDCLKO
(output)
t2
t3
t5
SDATA
(output)
t4
t6
t7
t8
SDATA
(input)
t9
t10
SRAS, SCAS,
SWE, SDCS
(output)
t11
t13
t12
t14
SDA, SBA
(output)
SDMASK
(output)
323 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.8 Microprocessor Bus AC Characteristics
Table 13-13. AC Characteristics—Microprocessor Bus Timing
(VDD3.3 = 3.3V ±5%, VDD1.8 = 1.8V ±5%, Tj = -40°C to +85°C.) (Note 1, Figure 13-9, Figure 13-10, Figure 13-11,
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
t1
0
ns
Setup Time for A[12:0] Valid to CS Active
t2
t3
t4
0
ns
ns
ns
Setup Time for CS Active to Either RD or WR Active
Delay Time from either RD or DS Active to DATA[7:0]
Valid
75
20
0
5
Hold Time from either RD or WR Inactive to CS Inactive
Hold Time from CS or RD or DS Inactive to DATA[7:0]
Tri-State
t5
ns
t6
t7
t8
t9
80
10
2
ns
ns
ns
ns
Wait Time from RW Active to Latch Data
Data Set Up Time to DS Active
Data Hold Time from RW Inactive
Address Hold from RW Inactive
0
Write Access to Subsequent Write/Read Access Delay
Time
t10
80
ns
Note 1: Timing parameters in this table are guaranteed by design (GBD).
324 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-9. Intel Bus Read Timing (MODEC = 00)
t9
Address Valid
ADDR[12:0]
DATA[7:0]
Data Valid
t5
WR
CS
t1
t2
t3
t4
RD
t10
Figure 13-10. Intel Bus Write Timing (MODEC = 00)
t9
Address Valid
ADDR[12:0]
DATA[7:0]
t7
t8
RD
t1
CS/CST
t2
t6
t4
WR
t10
325 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-11. Motorola Bus Read Timing (MODEC = 01)
t9
Address Valid
ADDR[12:0]
DATA[7:0]
Data Valid
t5
RW
t1
CS/CST
DS
t2
t3
t4
t10
Figure 13-12. Motorola Bus Write Timing (MODEC = 01)
t9
Address Valid
ADDR[12:0]
DATA[7:0]
t7
t8
RW
t1
CS/CST
t2
t6
t4
DS
t10
326 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.9 AC Characteristics: Receive-Side
Table 13-14. AC Characteristics: Receive Side
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
488 (E1)
648 (T1)
0.5 tLP
RDCLKO Period
tLP
tLH
ns
(Note 2)
200
RDCLKO Pulse Width
RDCLKO Pulse Width
ns
ns
tLL
tLH
tLL
(Note 2)
(Note 3)
(Note 3)
200
150
150
0.5 tLP
0.5 tLP
0.5 tLP
488 (E1)
648 (T1)
0.5 tCP
RDCLKI Period
tCP
ns
ns
tCH
tCL
20
20
RDCLKI Pulse Width
0.5 tCP
(Note 4)
(Note 5)
648
488
RSYSCLK Period
tSP
ns
ns
ns
tSH
tSL
20
20
0.5 tSP
0.5 tSP
RSYSCLK Pulse Width
RSYNC Setup to RSYSCLK Falling
RSYNC Pulse Width
tSU
20
50
ns
ns
tPW
RPOSI/RNEGI Setup to RDCLKI Falling
RPOSI/RNEGI Hold from RDCLKI Falling
RSYSCLK, RDCLKI Rise and Fall Times
Delay RDCLKO to RPOSO, RNEGO
Valid
tSU
tHD
20
20
ns
ns
ns
tR, tF
22
50
tDD
ns
Delay RCLKO to RSERO, RDATA, RSIG
Valid
tD1
50
ns
Delay RCLKO to RCHCLK, RSYNC,
RCHBLK, RFSYNC
tD2
tD3
tD4
50
22
22
ns
ns
ns
Delay RSYSCLK to RSERO, RSIG Valid
Delay RSYSCLK to RCHCLK, RCHBLK,
RMSYNC, RSYNC
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Note 2: Jitter attenuator enabled in the receive path.
Note 3: Jitter attenuator disabled or enabled in the transmit path.
Note 4: RSYSCLK = 1.544MHz.
Note 5: RSYSCLK = 2.048MHz.
327 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-13. Receive-Side Timing
RCLKO
t
D1
1ST FRAME BIT
RSERO / RDATA / RSIG
t
D2
D2
1
RSYNC
t
RFSYNC / RMSYNC
RCHCLK
t
D2
t
D2
RCHBLK
NOTE 1: RSYNC IS IN THE OUTPUT MODE.
NOTE 2: NO RELATIONSHIP BETWEEN RCHCLK AND RCHBLK AND OTHER SIGNALS IS IMPLIED.
328 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-14. Receive-Side Timing, Elastic Store Enabled
t
t
SL
SH
t
t
F
R
RSYSCLK
t
SP
t
D3
SEE NOTE 3
RSERO / RSIG
t
D4
RCHCLK
RCHBLK
RMSYNC
t
D4
t
t
D4
D4
1
RSYNC
t
HD
t
SU
2
RSYNC
NOTE 1: RSYNC IS IN THE OUTPUT MODE.
NOTE 2: RSYNC IS IN THE INPUT MODE.
NOTE 3: F-BIT WHEN MSTRREG.1 = 0, MSB OF TS0 WHEN MSTREG.1 = 1.
329 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.10 AC Characteristics: Backplane Clock Timing
Table 13-15. AC Characteristics: Backplane Clock Synthesis
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Delay RCLKO to BPCLK
tD1
10
ns
Note: Timing parameters in this table are guaranteed by design (GBD).
Figure 13-16. Receive Timing Delay RCLKO to BPCLK
RCLKO
t
D1
BPCLK
NOTE: IF RCLKO IS 1.544 MHZ, BPCLK WILL BE ASYNCHRONOUS.
331 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.11 AC Characteristics: Transmit Side
Table 13-16. AC Characteristics: Transmit Side
PARAMETER
TCLKT Period
SYMBOL
CONDITIONS
MIN
TYP (E1)
MAX
UNITS
488 (E1)
648 (T1)
0.5 tCP
tCP
ns
tCH
tCL
20
20
TCLKT Pulse Width
ns
0.5 tCP
488 (E1)
648 (T1)
0.5 tLP
0.5 tLP
648
TDCLKI Period
tLP
ns
ns
ns
ns
tLH
tLL
20
20
TDCLKI Pulse Width
TSYSCLK Period
TSYSCLK Pulse Width
(Note 2)
(Note 3)
tSP
448
0.5 tSP
20
20
tSP
0.5 tSP
TSYNC or TSSYNC Setup to TCLKT or
TSYSCLK Falling
tSU
20
50
ns
ns
TSYNC or TSSYNC Pulse Width
tPW
TSERI, TSIG, TDATA, TPOSI, TNEGI
Setup to TCLKT, TSYSCLK, TDCLKI
Falling
tSU
20
ns
TSERI, TSIG, TDATA Hold from TCLKT
or TSYSCLK Falling
tHD
tHD
20
20
ns
ns
TPOSI, TNEGI Hold from TDCLKI
Falling
TCLKT, TDCLKI or TSYSCLK Rise and
Fall Times
tR, tF
25
ns
Delay TCLKO to TPOSO, TNEGO Valid
Delay TCLKT to TESO, UT-UTDO Valid
tDD
tD1
50
50
ns
ns
Delay TCLKT to TCHBLK, TCHCLK,
TSYNC
tD2
tD3
50
22
ns
ns
Delay TSYSCLK to TCHCLK, TCHBLK
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Note 2: TSYSCLK = 1.544MHz.
Note 3: TSYSCLK = 2.048MHz.
332 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-17. Transmit-Side Timing
t
CP
t
t
CL
CH
t
t
F
R
TCLKT
t
D1
TESO
t
SU
TSERI / TSIG /
TDATA
t
t
HD
D2
TCHCLK
TCHBLK
t
D2
t
D2
t
1
TSYNC
t
HD
SU
2
TSYNC
t
D2
5
TLCLK
t
HD
TLINK
t
SU
NOTE 1: TSYNC IS IN THE OUTPUT MODE (IOCR1.1 = 1).
NOTE 2: TSYNC IS IN THE INPUT MODE (IOCR1.1 = 0).
NOTE 3: TSERI IS SAMPLED ON THE FALLING EDGE OF TCLKT WHEN THE TRANSMIT-SIDE ELASTIC STORE IS DISABLED.
NOTE 4: TCHCLK AND TCHBLK ARE SYNCHRONOUS WITH TCLKT WHEN THE TRANSMIT-SIDE ELASTIC STORE IS DISABLED.
333 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 13-18. Transmit-Side Timing, Elastic Store Enabled
t
SP
t
t
SL
SH
t
t
F
R
TSYSCLK
TSERI
t
SU
t
t
D3
HD
TCHCLK
TCHBLK
t
D3
t
HD
t
SU
TSSYNC
NOTE 1: TSERI IS ONLY SAMPLED ON THE FALLING EDGE OF TSYSCLK WHEN THE TRANSMIT-SIDE ELASTIC STORE IS ENABLED.
NOTE 2: TCHCLK AND TCHBLK ARE SYNCHRONOUS WITH TSYSCLK WHEN THE TRANSMIT-SIDE ELASTIC STORE IS ENABLED.
Figure 13-19. Transmit Line Interface Timing
TDCLKO
TPOSO, TNEGO
t
DD
t
LP
t
t
LL
LH
t
t
F
R
TDCLKI
t
SU
TPOSI, TNEGI
t
HD
334 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
13.12 JTAG Interface Timing
Table 13-17. JTAG Interface Timing
PARAMETER
SYMBOL
MIN
TYP
1000
500
MAX
UNITS
ns
JTCLK Clock Period
t1
t2 : t3
t4
JTCLK Clock High:Low Time (Note 2)
JTCLK to JTDI, JTMS Setup Time
JTCLK to JTDI, JTMS Hold Time
JTCLK to JTDO Delay
50
2
ns
ns
t5
2
ns
t6
2
50
50
ns
JTCLK to JTDO HIZ Delay
t7
2
ns
t8
100
ns
JTRST Width Low Time
Note 1: Timing parameters in this table are guaranteed by design (GBD).
Note 2: Clock can be stopped high or low
Figure 13-20. JTAG Interface Timing Diagram
t1
t2
t3
JTCLK
t4
t5
JTDI, JTMS
t6
t7
JTD0
t8
335 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14 JTAG INFORMATION
The DS33R11 contains two JTAG ports. Port 1 is for the Ethernet Mapper, and Port 2 is for the T1/E1/J1
Transceiver. Because of this, this device requires special consideration during JTAG test design. For more
The device supports the standard instruction codes SAMPLE:PRELOAD, BYPASS, and EXTEST. Optional public
instructions included are HIGHZ, CLAMP, and IDCODE. See Table 14-1. The DS33R11 contains the following as
required by IEEE 1149.1 Standard Test Access Port and Boundary Scan Architecture.
Test Access Port (TAP)
TAP Controller
Instruction Register
Bypass Register
Boundary Scan Register
Device Identification Register
The Test Access Port has the necessary interface pins: JTRST, JTCLK, JTMS, JTDI, and JTDO. See the pin
descriptions for details. Refer to IEEE 1149.1-1990, IEEE 1149.1a-1993, and IEEE 1149.1b-1994 for details about
the Boundary Scan Architecture and the Test Access Port.
Figure 14-1. JTAG Functional Block Diagram
Boundary Scan
Register
Identification
Register
Bypass
Register
Instruction
Register
Select
Test Access Port
Controller
Tri-State
10K
10K
10K
JTDI
JTMS
JTCLK
JTDO
JTRST
336 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14.1 JTAG TAP Controller State Machine Description
This section covers the details on the operation of the Test Access Port (TAP) Controller State Machine. The TAP
controller is a finite state machine that responds to the logic level at JTMS on the rising edge of JTCLK.
TAP Controller State Machine
The TAP controller is a finite state machine that responds to the logic level at JTMS on the rising edge of JTCLK.
Test-Logic-Reset
Upon power up, the TAP Controller is in the Test-Logic-Reset state. The Instruction register will contain the
IDCODE instruction. All system logic of the device will operate normally.
Run-Test-Idle
The Run-Test-Idle is used between scan operations or during specific tests. The Instruction register and test
registers will remain idle.
Select-DR-Scan
All test registers retain their previous state. With JTMS LOW, a rising edge of JTCLK moves the controller into the
Capture-DR state and will initiate a scan sequence. JTMS HIGH during a rising edge on JTCLK moves the
controller to the Select-IR-Scan state.
Capture-DR
Data may be parallel-loaded into the test data registers selected by the current instruction. If the instruction does
not call for a parallel load or the selected register does not allow parallel loads, the test register will remain at its
current value. On the rising edge of JTCLK, the controller will go to the Shift-DR state if JTMS is LOW or it will go
to the Exit1-DR state if JTMS is HIGH.
Shift-DR
The test data register selected by the current instruction is connected between JTDI and JTDO and will shift data
one stage towards its serial output on each rising edge of JTCLK. If a test register selected by the current
instruction is not placed in the serial path, it will maintain its previous state.
Exit1-DR
While in this state, a rising edge on JTCLK will put the controller in the Update-DR state, which terminates the
scanning process, if JTMS is HIGH. A rising edge on JTCLK with JTMS LOW will put the controller in the Pause-
DR state.
Pause-DR
Shifting of the test registers is halted while in this state. All test registers selected by the current instruction will
retain their previous state. The controller will remain in this state while JTMS is LOW. A rising edge on JTCLK
with JTMS HIGH will put the controller in the Exit2-DR state.
Exit2-DR
A rising edge on JTCLK with JTMS HIGH while in this state will put the controller in the Update-DR state and
terminate the scanning process. A rising edge on JTCLK with JTMS LOW will enter the Shift-DR state.
337 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Update-DR
A falling edge on JTCLK while in the Update-DR state will latch the data from the shift register path of the test
registers into the data output latches. This prevents changes at the parallel output due to changes in the shift
register.
Select-IR-Scan
All test registers retain their previous state. The instruction register will remain unchanged during this state. With
JTMS LOW, a rising edge on JTCLK moves the controller into the Capture-IR state and will initiate a scan
sequence for the instruction register. JTMS HIGH during a rising edge on JTCLK puts the controller back into the
Test-Logic-Reset state.
Capture-IR
The Capture-IR state is used to load the shift register in the instruction register with a fixed value. This value is
loaded on the rising edge of JTCLK. If JTMS is HIGH on the rising edge of JTCLK, the controller will enter the
Exit1-IR state. If JTMS is LOW on the rising edge of JTCLK, the controller will enter the Shift-IR state.
Shift-IR
In this state, the shift register in the instruction register is connected between JTDI and JTDO and shifts data one
stage for every rising edge of JTCLK towards the serial output. The parallel register, as well as all test registers,
remains at their previous states. A rising edge on JTCLK with JTMS HIGH will move the controller to the Exit1-IR
state. A rising edge on JTCLK with JTMS LOW will keep the controller in the Shift-IR state while moving data one
stage thorough the instruction shift register.
Exit1-IR
A rising edge on JTCLK with JTMS LOW will put the controller in the Pause-IR state. If JTMS is HIGH on the rising
edge of JTCLK, the controller will enter the Update-IR state and terminate the scanning process.
Pause-IR
Shifting of the instruction shift register is halted temporarily. With JTMS HIGH, a rising edge on JTCLK will put the
controller in the Exit2-IR state. The controller will remain in the Pause-IR state if JTMS is LOW during a rising
edge on JTCLK.
Exit2-IR
A rising edge on JTCLK with JTMS LOW will put the controller in the Update-IR state. The controller will loop back
to Shift-IR if JTMS is HIGH during a rising edge of JTCLK in this state.
Update-IR
The instruction code shifted into the instruction shift register is latched into the parallel output on the falling edge of
JTCLK as the controller enters this state. Once latched, this instruction becomes the current instruction. A rising
edge on JTCLK with JTMS held low will put the controller in the Run-Test-Idle state. With JTMS HIGH, the
controller will enter the Select-DR-Scan state.
338 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Figure 14-2. TAP Controller State Diagram
Test Logic
Reset
1
0
0
1
1
1
Run Test/
Idle
Select
Select
DR-Scan
IR-Scan
0
0
1
1
Capture DR
Capture IR
0
0
Shift DR
Shift IR
0
1
0
1
1
1
Exit DR
Exit IR
0
0
Pause DR
Pause IR
0
0
1
1
0
0
Exit2 DR
Exit2 IR
1
1
Update DR
Update IR
1
0
1
0
14.2 Instruction Register
The instruction register contains a shift register as well as a latched parallel output and is 3 bits in length. When
the TAP controller enters the Shift-IR state, the instruction shift register is connected between JTDI and JTDO.
While in the Shift-IR state, a rising edge on JTCLK with JTMS LOW will shift the data one stage towards the serial
output at JTDO. A rising edge on JTCLK in the Exit1-IR state or the Exit2-IR state with JTMS HIGH will move the
controller to the Update-IR state. The falling edge of that same JTCLK will latch the data in the instruction shift
register to the instruction parallel output. Instructions supported by the DS26521 and its respective operational
339 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
Table 14-1. Instruction Codes for IEEE 1149.1 Architecture
INSTRUCTION
SELECTED REGISTER
INSTRUCTION CODES
SAMPLE:PRELOAD
BYPASS
Boundary Scan
Bypass
Boundary Scan
Bypass
010
111
000
011
100
001
EXTEST
CLAMP
HIGHZ
IDCODE
Bypass
Device Identification
SAMPLE:PRELOAD
This is a mandatory instruction for the IEEE 1149.1 specification. This instruction supports two functions. The
digital I/Os of the device can be sampled at the boundary scan register without interfering with the normal
operation of the device by using the Capture-DR state. SAMPLE:PRELOAD also allows the device to shift data
into the boundary scan register via JTDI using the Shift-DR state.
BYPASS
When the BYPASS instruction is latched into the parallel instruction register, JTDI connects to JTDO through the
one-bit bypass test register. This allows data to pass from JTDI to JTDO not affecting the device’s normal
operation.
EXTEST
This allows testing of all interconnections to the device. When the EXTEST instruction is latched in the instruction
register, the following actions occur. Once enabled via the Update-IR state, the parallel outputs of all digital output
pins are driven. The boundary scan register is connected between JTDI and JTDO. The Capture-DR will sample
all digital inputs into the boundary scan register.
CLAMP
All digital outputs of the device will output data from the boundary scan parallel output while connecting the bypass
register between JTDI and JTDO. The outputs will not change during the CLAMP instruction.
HIGHZ
All digital outputs of the device are placed in a high-impedance state. The BYPASS register is connected between
JTDI and JTDO.
IDCODE
When the IDCODE instruction is latched into the parallel instruction register, the identification test register is
selected. The device identification code is loaded into the identification register on the rising edge of JTCLK
following entry into the Capture-DR state. Shift-DR can be used to shift the identification code out serially via
JTDO. During Test-Logic-Reset, the identification code is forced into the instruction register’s parallel output. The
ID code will always have a ‘1’ in the LSB position. The next 11 bits identify the manufacturer’s JEDEC number and
number of continuation bytes followed by 16 bits for the device and 4 bits for the version.
340 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14.3 JTAG ID Codes
Table 14-2. ID Code Structure
REVISION
DEVICE
DEVICE CODE
ID[27:12]
MANUFACTURER’S CODE
ID[11:1]
REQUIRED
ID[0]
ID[31:28]
Ethernet
Mapper
0000
0000
0000 0000 0110 0001
0000 0000 0001 0000
000 1010 0001
000 1010 0001
1
1
T1/E1/J1
Transceiver
14.4 Test Registers
IEEE 1149.1 requires a minimum of two test registers: the bypass register and the boundary scan register. An
optional test register has been included with the DS26521 design. This test register is the identification register
and is used in conjunction with the IDCODE instruction and the Test-Logic-Reset state of the TAP controller.
14.4.1 Boundary Scan Register
This register contains both a shift register path and a latched parallel output for all control cells and digital I/O cells
and is n bits in length.
14.4.2 Bypass Register
This is a single one-bit shift register used in conjunction with the BYPASS, CLAMP, and HIGHZ instructions, which
provides a short path between JTDI and JTDO.
14.4.3 Identification Register
The identification register contains a 32-bit shift register and a 32-bit latched parallel output. This register is
selected during the IDCODE instruction and when the TAP controller is in the Test-Logic-Reset state.
341 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
14.5 JTAG Functional Timing
This functional timing for the JTAG circuits shows:
•
•
•
•
•
The JTAG controller starting from reset state.
Shifting out the first 4 LSB bits of the IDCODE.
Shifting in the BYPASS instruction (111) while shifting out the mandatory X01 pattern.
Shifting the TDI pin to the TDO pin through the bypass shift register.
An asynchronous reset occurs while shifting.
Figure 14-3. JTAG Functional Timing
IDCODE
(INST)
(STATE)
JTCLK
IDCODE
BYPASS
Update
DR
Shift IR
Test
Logic Idle
Run Test Select DR
Idle Scan
Capture
DR
Exit1
DR
Select DR
Scan
Select IR
Scan
Capture
IR
Exit1
IR
Update
IR
Select DR
Scan
Capture
DR
Shift
DR
Reset
Shift
DR
JTRST
JTMS
X
X
X
JTDI
X
X
JTDO
X
Output
Pin
Output pin level change if in "EXTEST" instruction mode
342 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
15 PACKAGE INFORMATION
(The package drawing(s) in this data sheet may not reflect the most current specifications. The package number provided for
each package is a link to the latest package outline information.)
343 of 344
Download from Www.Somanuals.com. All Manuals Search And Download.
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
16 DOCUMENT REVISION HISTORY
REVISION
DESCRIPTION
072105
New product release.
(Page 28) Corrected pin description of REF_CLK.
(Page 28) Clarified text regarding use of REF_CLKO in DCE and RMII modes.
(Page 29) Corrected pin description of MDC.
(Page 43) In Section 9.1, removed from third bullet the sentence “The user can utilize the built-
in REF_CLKO output clock to drive this input.” Also removed from the fifth bullet the sentence
“This output clock can be used as an input to REF_CLK, allowing the user to have one less
oscillator for the system.”
(Page 45) In Section 9.1.1, updated the section to show that in DCE and RMII operating modes,
the REF_CLKO signal should not be used to provide an input to REF_CLK, due to the reset
requirements in these operating modes.
(Page 46) In Section 9.2, corrected low-power mode information.
(Page 56) In Section 9.14, removed the following sentence from the first paragraph: “The
REF_CLKO output can be used to source the REF_CLK input.”
030807
(Page 68) In Section 9.19, clarified X.86 mode synchronization.
(Page 123) In Table 11-7, corrected SU.MACCR register map.
(Page 173) Corrected SU.GCR.H10S bit definition.
(Page 183) Corrected default value for RMPS (bit 0) in the SU.RMFSRL register definition.
(Page 183) Corrected the SU.RQLT and SU.RQHT default values to zero.
(Page 186) Corrected SU.MACCR.PM and SU.MACCR.PAM bit definitions.
(Page 319) In Table 13-10, added TCLKE to TBSYNC Setup Time Minimum of 3.5ns.
(Page 334) Added a note regarding the special considerations required for dual JTAG
controllers.
344 of 344
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2007 Maxim Integrated Products
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.
Download from Www.Somanuals.com. All Manuals Search And Download.
|