Matsushita Laptop CF 18NHHZXBM User Manual
ORDER NO. CPD0604070C1  
Notebook Computer  
CF-18  
This is the Service Manual for  
the following areas.  
M …for U.S.A. and Canada  
Model No. CF-18NHHZXBM  
© 2006 Matsushita Electric Industrial Co., Ltd. All rights reserved.  
Unauthorized copying and distribution is a violation of law.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LASER SAFETY INFORMATION  
For U.S.A.  
Class 1 LASER-Product  
This product is certified to comply with DHHS Rules 21 CFR Subchapter J.  
This product complies with European Standard EN60825 (or IEC Publication 825)  
For all areas  
This equipment is classified as a class 1 level LASER product and there is no hazardous LASER radiation.  
Caution:  
(1) Use of controls or adjustments or performance of procedures other than those specified herein may result in  
hazardous radiation exposure.  
(2) The drive is designed to be incorporated into a computer-based system or unit which has an enclosing cover.  
It should never be used as a stand alone drive.  
Danger:  
The serviceman should not remove the cover of drive unit and should not service because the drive unit is a non-  
serviceable part.  
Please check DANGER label on PD-drive unit.  
• Unplug the AC power cord to the equipment before opening the top cover of the drive.  
When the power switch it on, do not place your eyes close to the front panel door to look into the interior of the unit.  
LASER Specification  
Class 1 level LASER Product  
Wave Length: DVD 658±8 nm  
CD 775~815 nm  
Laser safety information is appropriate only when drive with laser is installed.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
1 Diagnosis Procedure ······································································································1-1  
2 Power-On Self Test (Boot Check) ··················································································2-1  
3 List of Error Codes ··········································································································3-1  
4 Diagnostic Test ···············································································································4-1  
5 Self Diagnosis Test ·········································································································5-1  
6 Wiring Connection Diagram ···························································································6-1  
7 Disassembly/Reassembly ······························································································7-1  
8 Exploded View ················································································································8-1  
9 Replacement Parts List ··································································································9-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Diagnosis Procedure  
1.1. Basic Procedure  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.2. Troubleshooting  
Please take note of the following two points with regard to troubleshooting:  
1. Know-how of diagnosis upon occurrence of heavy troubles, e.g. ‘Set cannot be turned ON’, ‘Set fails to start’, ‘No display on  
screen’, etc.  
2. Explanation of each trouble, mainly symptom of trouble in operation.  
Flow Chart  
Pay attention to the following points when in pursuit of the cause of a troubleshooting.  
1. Peripheral apparatus connected with the set should all be removed before operation check.  
2. Make sure that cables, boards, etc. are not coming off, and recheck the contact condition.  
START  
AC  
NG  
Set cannot be supplied with current.  
Power lamp fails to light up.  
Adaptor/Battery  
Output voltage  
Replace AC Adaptor/Battery  
OK  
Check contact condition of power input terminal. Replace if  
defective.  
Check Power SW. Replace if defective.  
NO  
YES  
NG  
Power lamp  
check  
Dark display on screen.  
Screen fails to display.  
Replace inverter board.  
Check inverter cable continuity. Replace if defective  
Inverter board  
OK  
NO  
NG  
LCD back  
Replace LCD back light.  
light lighting  
YES  
LCD unit  
check  
Replace LCD unit.  
OK  
NO  
BIOS operation  
check  
Replace main board (Check fuse at power source).  
Failure in starting  
YES  
NG  
OK  
NG  
Refer to POST  
error code table.  
Result of  
POST  
Replace main board.  
Heavy trouble e.g.,  
Set-up utility  
starting  
Replace main board.  
‘Set cannot be turned  
ON’, ‘Set fails to start’,  
‘No display on  
OK  
Return set-up utility setpoint to the state of ‘delivery from factory’.  
screen’, etc.  
Check HDD cable connection and continuity.  
NO  
Replace if defective.  
Replace HDD & Reinstall.  
Replace main board.  
HDD access  
YES  
NG  
Main board  
check  
Replace main board  
Not displayed properly on screen.  
Some or all keys cannot be input.  
OK  
Make sure of contact of K/B connector in use.  
Replace keyboard or main board.  
Each kind of  
trouble in  
operation.  
Check if there are any flaws on DVD or CD  
media. Since flaws may appear on specific  
media, DVD or CD media can be defective.  
NO  
Trouble  
symptoms on some  
of DVD or CD  
DVD/CD CALL not practicable.  
YES  
Replace DVD drive.  
Replace main board.  
*Clean DVD-ROM drive with an applicator.  
Starts but operates unstably.  
Reinstall HDD.  
Replace main board.  
END  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 Power-On Self Test (Boot Check)  
Outline of POST  
The set has a boot check function called POST (Power-On Self Test) in it. The condition of the main body is diagnosed by checking  
beep sound or error code.  
Start .............Test begins automatically when power switch is set to ON.  
Normal finish .....After memory checking, a beep sound is issued once and the set is placed into automatic stop.  
Note: If no error occurs, nothing is displayed. (No display of OK, etc.)  
Error Diagnosis by Checking Beep Signal Sound  
The beep sound is as follows:  
(1 (long sound) -2-3-4)  
(Length of bar shows length of sound.)  
= long sound (about 0.4 sec.),  
= short sound (about 0.2 sec.), Length between sounds is about 0.1 sec.  
Table of errors classified by beep sounds  
Diagnosis  
Beep signal sound  
Error message  
BIOS ROM error  
Main board  
1(long sound)-2  
1-2-2-3  
BIOS ROM error  
1-3-1-1  
RAM error  
1-3-1-3  
Keyboard controller error  
RAM error  
1-3-4-1  
1-3-4-3  
RAM error  
1-4-1-1  
RAM error  
2-1-2-3  
BIOS ROM error  
2-2-3-1  
Occurrence of unexpected offering  
(Note) A beep sound is also issued in case of other I/O trouble.  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. ListofErrorCodes<Only when the port replicator is connected>  
The following is a list of the messages that BIOS can display. Most of them occur during POST.  
Some of them display information about a hardware device, e.g., the amount of memory  
installed. Others may indicate a problem with a device, such as the way it has been configured.  
Following the list are explanations of the messages and remedies for reported problems.  
If your system displays one of except the messages marked below with an asterisk (*), write  
down the message and contact Panasonic Technical Support. If your system fails after you make  
changes in the Setup menus, reset the computer, enter Setup and install Setup defaults or correct  
the error.  
0200 Failure Fixed Disk  
Fixed disk in not working or not configured properly. Check to see if fixed disk is attached  
properly. Run Setup. Find out if the fixed-disk type is correctly identified.  
0210 Stuck key  
Stuck key on keyboard.  
0211 Keyboard error  
Keyboard not working.  
0212 Keyboard Controller Failed  
Keyboard controller failed test. May require replacing keyboard controller.  
0213 Keyboard locked - Unlock key switch  
Unlock the system to proceed.  
0230 System RAM Failed at offset: nnnn  
System RAM failed at offset nnnn of in the 64k block at which the error was detected.  
0231 Shadow RAM Failed at offset: nnnn  
Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.  
0232 Extended RAM Failed at offset: nnnn  
Extended memory not working or not configured properly at offset nnnn.  
0250 System battery is dead - Replace and run SETUP  
The CMOS clock battery indicator shows the battery is dead. Replace the battery and run  
Setup to reconfigure the system.  
*0251 System CMOS checksum bad - Default configuration used  
System CMOS has been corrupted or modified incorrectly, perhaps by an application  
program that changes data stored in CMOS. The BIOS installed Default SETUP Values.  
If you do not want these values, enter Setup and enter your own values. If the error persists,  
check the system battery or contact Panasonic Technical Support.  
0260 System timer error  
The timer test failed. Requires repair of system board.  
0270 Real time clock error  
Real-time clock fails BIOS test. May require board repair.  
*0280 Previous boot incomplete - Default configuration used  
Previous POST did not complete successfully. POST loads default values and offers to run  
Setup. If the failure was caused by incorrect values and they are not corrected, the next boot  
will likely fail. On systems with control of wait states, improper Setup settings can also  
terminate POST and cause this error on the next boot. Run Setup and verify that the  
wait-state configuration is correct. This error is cleared the next time the system is booted.  
0281 Memory Size found by POST differed from EISA CMOS  
Memory size found by POST differed from EISA CMOS.  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
02D0 System cache error - Cache disabled  
Contact Panasonic Technical Support.  
02F0: CPU ID:  
CPU socket number for Multi-Processor error.  
02F4: EISA CMOS not writable  
ServerBIOS2 test error: Cannot write to EISA CMOS.  
02F5: DMA Test Failed  
ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.  
02F6: Software NMI Failed  
ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).  
02F7: Fail - Safe Timer NMI Failed  
ServerBIOS2 test error: Fail-Safe Timer takes too long.  
device address Conflict  
Address conflict for specified device.  
Allocation Error for: device  
Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device.  
Failing Bits: nnnn  
The hex number nnnn is a map of the bits at the RAM address which failed the memory test.  
Each 1 (one) in the map indicates a failed bit. See error 230,231 or 232 for offset address of  
the failure in System, Extended or Shadow memory.  
Invalid System Configuration Data  
Problem with NVRAM (CMOS) data.  
I/O device IRQ conflict  
I/O device IRQ conflict error.  
Operating System not found  
Operating system cannot be located on either drive A: or drive C: Enter Setup and see if  
fixed disk and drive A: are properly identified.  
Parity Check 1 nnnn  
Parity error found in the system bus. BIOS attempts to locate the address and display it on  
the screen. If it cannot locate the address, it displays ????. Parity is a method for checking  
errors in binary data. A parity error indicates that some data has been corrupted.  
Parity Check 2 nnnn  
Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the  
screen. If it cannot locate the address, it displays ????.  
Press <F1> to resume, <F2> to Setup  
Displayed after any recoverable error message. Press <F1> to start the boot process or <F2>  
to enter a Setup and change the settings. Write down and follow the information shown on  
the screen.  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Diagnostic Test  
4.1 Equipment  
(1) Test Computer ································································································ 1 unit  
(2) External Floppy Disk Drive ············································································· 1 unit  
(3) AC Adapter ····································································································· 1 pc.  
(4) Loopback Plug (Serial Port Test for RS232C) [ P/N: DFWV95C0067 ] ········· 1 pc.  
(5) Floppy Disk containg file DIAG ······································································· 1 pc.  
4.2 Preparation  
(1) Connect the AC Adapter and External Equipments.  
(2) The System Setup should be set to the factory setting values by executing the “SETUP  
UTILITY” which can be invoked by F2 key at the POST.  
If not, the messages and items of the diagnostic test may not be displayed properly on the  
LCD.  
(3) The serial port must be enabled in the “SETUP UTILITY” in order to execute the “1st SERIAL  
PORT” test.  
(4) Connect the serial loopback plug.  
4-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5 Self Diagnosis Test  
Floppy disk is Included for the self-diagnostic tests that should be performed before using this product.  
Important notice  
1. System password  
If the password function has been turned on, you will need to ask the user for the password  
before performing the self-diagnostics.  
2. FDD test  
Performing the FDD test will erase the contents of the floppy disk you insert into the drive. Use  
a formatted disk that has no contents or whose contents are not required. This product has a  
password function. However, if this function is turned on, the self-diagnostics tests will not work.  
5.1. Outline of Self Diagnostic Tests  
Insert the diagnostics floppy disk  
Starting up the setup utility  
Turn on the power.  
When "Panasonic Press F2 to enter setup" appears  
on the screen, press F2.  
Press " " to select Exit  
Press " " to select Get default value  
Press Enter.  
Return the setup  
contents to default  
Choose Yes for "Load default Configuration now?"  
Select "Save Values & Exit" and press Enter.  
Choose Yes for "Save Configuration changes and exit now?"  
and press Enter.  
Menu Screen  
Choose test from  
(
)
1. DIAG on FD CF-18 XP/2000 Model  
the menu screen  
to start the test.  
(
)
2. DIAG on FD CF-18 Tablet Model  
3. LAN Test  
4. Modem Test  
(
)
5. Wireless LAN test Wireless LAN Model only  
6. Button Test  
Caution:  
After completing repairs, be sure  
to carry out the Automatic test  
and Peripheraltest.  
Q. Quit  
Select please [ 1, 2, 3, 4, 5, 6, Q ] ?  
<Automatic test>  
<Peripheral test>  
<Test selection>  
Tests selected (O) from the test  
item list will be performed in  
succession.  
The parallel port and CD-ROM Specifc tests required can  
drive can be tested.  
(See 5.3 for details.)  
be freely selected and  
performed from the test item  
list.  
3. LAN Test  
DIAG on FD  
4. Modem Test  
5. Wireless LAN test Wireless LAN Model only  
6. Button Test  
Be sure to carry out the Selection  
test only when necessary.  
(
)
Problems in the unit are located and divided according  
to error messages that occur during testing.  
5-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.1.1 List of main test items  
The Selection item displays the items selected under Automatic test. If you select Automatic test, these test items  
will be performed automatically. You can use Selection test to choose items from the menu screen that you want to  
have tested.  
These items are shown below.  
1
SPEAKER TEST  
Speaker test  
2
VESA MODE TEST  
A20 GATE TEST  
VESA mode test  
CPU  
3
Address A20 line  
(CPU related)  
4
CACHE ON/OFF TEST  
NPU OPERAND TEST  
RAM STANDARD TEST  
DMA PAGE REG TEST  
DMA REGISTER TEST  
DMAC TRANSFER TEST  
PIC HALT INSTRUCTION TEST  
PIC REGISTER TEST  
RTC CMOS RAM TEST  
RTC TEST  
Cache memory on/off test  
Floating point processor function test  
Memory standard test  
DMA page register test  
DAM register test  
5
RAM (Memory related)  
CONTROL  
(Control ICs on the main  
board, etc.)  
6
7
8
9
DAM transfer test  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
Interrupt controller halt instruction test  
Interrupt controller register test  
Real time clock CMOS test  
Real time clock test  
interrupt timer CH0  
PIT CH0 TEST  
PIT CH1 TEST  
interrupt timer CH1  
PIT CH2 TEST  
interrupt timer CH2  
IO  
KEYBOARD REG TEST  
PS/2 MOUSE REG  
SERIAL WRAP TEST  
SERIAL ALL INTERNAL TEST  
PARALLEL REGISTER R/W  
PCIC ALL TEST  
Keyboard test  
(Input-output)  
Mouse registration test  
Serial loop back (jig required)  
Serial port interior test  
Parallel register R/W test  
PCIC test  
COMMUNICATION  
AUX  
(Auxiliary functions)  
Card Bus Reg  
Card Bus register test  
USB register test  
USB Reg  
VIDEO  
(Display related)  
VGA ALL TEST  
VGA test  
SVGA RAM TEST  
SVGA RAM test  
DISK  
(FDD, HDD)  
FD WT/RD/WP TEST  
HDD ALL TEST  
FD WT, RD WP test  
Only HDD lead test selected  
ECP register R/W test  
EPP register R/W test  
Extension CMOS R/W test  
UNIQUE  
(Individual functions)  
ECP REGISTER R/W  
EPP REGISTER R/W  
EXT. CMOS R/W TEST  
Test function settings  
Test condition save/play  
Test automatic execute  
Error display (Paging style)  
Following file command  
Test executed on run settings by selecting command  
Select displayed items Error, Log, Option  
5.2. Automatic Test  
Test execution  
From the menu screen shown below For Celeron models Select and press Enter for DIAG on FD  
(
)
1. DIAG on FD CF-18 XP/2000 Model  
(
)
2. DIAG on FD CF-18 Tablet Model  
3. LAN Test  
4. Modem Test  
5. Wireless LAN test Wireless LAN Model only  
6. Button Test  
(
)
Q. Quit  
Select please [ 1, 2, 3, 4, 5, 6, Q ] ?  
menu screen  
5-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker test, VESA test  
The speaker test involves listening to music and choosing OK or Not okay. The VESA test involves looking at  
the display to see if it is satisfactory then choosing OK or Not okay.  
Serial loop back test  
The Automatic test’s initial settings are set so that the serial loop back test will be executed. Connect the serial  
loop back jig and then perform the test.  
(This test is not executed on default mode)  
Diagnostics result  
If no errors occur. The screen shows the word "Pass" in large letters.  
If errors occur. The test is stopped when an error occurs and the error message is displayed.  
For explanations of error messages, see Error Messages and Problem Categories (section 5.5).  
Quitting the test  
At the screen shown below, simultaneously press the ALT and X keys.  
Input screen  
5.3. Peripheral Test  
Test execution  
From the menu screen shown below, be sure to choose the following items and press Enter.  
(
)
1. DIAG on FD CF-18 XP/2000 Model  
(
)
2. DIAG on FD CF-18 Tablet Model  
3. LAN Test  
4. Modem Test  
5. Wireless LAN test Wireless LAN Model only  
6. Button Test  
(
)
Q. Quit  
Select please [ 1, 2, 3, 4, 5, 6, Q ] ?  
menu screen  
3. LAN Test  
4. Modem Test  
5. Wireless LAN Test  
(
)
Wireless LAN Model only.  
This test checks for internal LAN device.  
Choose LAN test and press Enter.  
5-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5 .4. Test Selection  
Starting up the input menu  
1. From the menu screen shown below, choose Quit and press Enter.  
(
)
1. DIAG on FD CF-18 XP/2000 Model  
(
)
2. DIAG on FD CF-18 Tablet Model  
3. LAN Test  
4. Modem Test  
5. Wireless LAN test Wireless LAN Model only  
6. Button Test  
(
)
Q. Quit  
Select please [ 1, 2, 3, 4, 5, 6, Q ] ?  
menu screen  
2. When A: \DIAG appears, input "JDG_185" and press Enter.  
3. The input screen shown below will appear.  
To choose menu items, hold down "ALT" and press the selection key.  
5-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Example:  
"ALT" + "F" brings up the File menu.  
Input screen  
Order of test flow selection  
Input screen startup  
1. Reading the test conditions settings file  
If the test condition settings  
file is not read, this means  
Press "AL T" and "F".  
Press "L".  
the test program is not running correctly  
.
Press "AL T" and "C".  
2. setting the test items  
Press "AL T" and "S".  
Saving selected test items  
If you change the file name when  
saving the file in step , you can  
create test condition settings for  
custom test items.  
Press "S".  
Choose the test item and press Enter  
Choose the test whose settings are  
to be changed, press "A" for Additional  
and "R" for Erase.  
.
Example:  
CF-18  
TEST1.  
.
All initial V Alues are "0" so set  
tests other than the necessary ones to "1".  
Press "C" twice to return the menu screen.  
To save the selected list, press "AL T" and "F" at the file menu.  
Starting the test  
Press "AL T" and "R".  
Press "R".  
This will start the test.  
End of test  
5-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.5. Error Messages and Troubleshooting  
The table below explains the parts that may be faulty or damaged should an error message occur while performing the  
various test items of the self diagnostics program.  
Test classification  
CPU  
(CPU related)  
Screen display test items  
A20 GATE TEST  
CACHE ON/OFF  
NPU OPERAND TEST  
RAM STANDARD  
DMA PAGE REG TEST  
DMA REGISTER TEST  
DMAC Transfer TEST  
PIC HALT INSTRUCTION TEST  
PIC REGISTER TEST  
RTC CMOS RAM TEST  
Contents  
Address 20 line  
Cache memory on/off  
Floating point processor function  
Memory standard  
DMA page register  
DAM register  
DAM transfer test  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
RAM (Memory related)  
CONTROL  
(Control ICs on the  
main board, etc.)  
Interrupt controller  
Interrupt controller  
Real time clock CMOS  
SPEAKER TEST  
PIT CH0 TEST  
PIT CH1 TEST  
PIT CH2 TEST  
KEYBOARD REG TEST  
PS/2 MOUSE REG  
SERIAL WRAP TEST  
SERIAL ALL INTERNAL TEST  
PARALLEL REGISTER R/W  
PCIC ALL TEST  
Speaker  
Interrupt timer CH0  
Interrupt timer CH1  
Interrupt timer CH2  
Keyboard  
16 IO  
17 (Input-output)  
18 COMMUNICATION  
Mouse  
Serial loop back (jig required)  
Serial port  
Parallel register  
PCIC  
19  
20  
AUX  
21  
Card Bus REG  
USB REG  
Card Bus port  
USB port  
(Auxiliary functions)  
VGA ALL TEST  
VGA  
22 VIDEO  
SVGA RAM TEST  
VESA MODE TEST  
FD WT/RD/WP TEST  
HDD ALL TEST  
ECP REGISTER R/W  
EPP REGISTER R/W  
EXT. CMOS R/W TEST  
SVGA RAM  
VESA mode  
FD write/read/write protection  
Only HDD lead selected  
Parallel port  
23 (Display related)  
24  
25 DISK  
26 (FDD, HDD)  
27 UNIQUE  
28 (Individual functions)  
29  
Parallel port  
Extension CMOS R/W test  
5-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6 Wiring Connection Diagram  
INVERTER PCB  
BACK LIGHT  
LCD  
CN1 CN2  
EXTERNAL  
DISPLAY  
PORT  
TS PS2 PCB  
SERIAL PORT  
CN881  
CN880  
CN901  
I/O PCB  
Touch  
Screen  
Panel  
CN883  
JK880  
CN900  
CN880  
DC-IN  
RTC  
BATTERY  
I/F PCB  
H/P MIC  
CN850  
JK902 JK901  
CN900  
CN16  
CN27  
CN902  
CN14  
CN3  
CN9  
CN6  
CN901  
USB PORT  
CN25  
AUDIO PCB  
CN18  
CN11  
USB PORT  
SD PCB  
CN7  
KEYBOARD  
CN17  
CN8  
CN24  
CN891  
CN5  
LAN PORT  
SPEAKER  
MAIN PCB  
CN12  
CN37  
CN4  
J1  
WIRELESS  
MODULE  
CN21  
HDD  
J5  
LAN-  
AUX  
J1  
MAIN  
BATTERY  
CN30  
J6  
CN35  
J2  
MODEM  
PORT  
CN23  
PMCIA UNIT  
SW4  
POWER  
MODEM PCB  
CN800  
ANT PCB  
PAD PCB  
CN1  
CN2  
GPRS  
CN4  
CN5  
CN801  
LAN-  
MAIN  
CN3  
CN802  
LED PCB  
TOUCH PAD  
SW PCB  
CN841  
CN950  
6-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7 Disassembly/Reassembly  
Note:  
Power off the computer. Do not shut down to the Suspend or hibernation mode.  
Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.  
7.1. Disassembly Instructions  
4. Remove the HDD Pack.  
7.1.1.  
Preparation  
Before disassembling, be sure to make the following prepara-  
tions.  
HDD Case B  
Hooks  
• Shut down Windows and turn off the power.  
• Disconnect the AC adaptor.  
HDD FPC  
• Remove the optional DIMM memory card and PCMCIA card  
if they are connected.  
HDD  
Hooks  
• Remove other devices if they are connected.  
Attention:  
• Please execute writing BIOS ID when you exchange the  
Main Board.  
• Parts (Sheet and rubber) etc. related various the Conductive  
Cloth and Heat Spreader cannot be recycled. Use new parts.  
Heater  
<A>  
<A>  
7.1.2.  
Removing the Battery Pack and  
HDD Pack  
HDD Case A  
5. Remove the two Screws <A>.  
6. Remove the HDD Case A and the HDD Case B.  
7. Remove the HDD.  
1
3
2
Screws <A>:DFHE5025XA  
7.1.3.  
Removing the Touch Pad and Key-  
board  
KBD Plate  
<B>  
<B>  
KBD Plate  
<B>  
Palm Rest Ass'y  
<B>  
HDD Pack  
Battery Pack  
1. Open the Battery Cover.  
2. Remove the Battery Pack.  
3. Open the HDD Cover.  
1. Remove the Palm Rest Ass'y.  
Note:  
The Palm Rest Ass'y is firmly fixed with two-sided  
tape.  
Carefully remove the Palm Top Cover Sheet not to  
damage it.  
2. Remove the four Screws <B>.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-1  
3. Remove the KBD Plate.  
9. Remove the TP Tape.  
10. Disconnect the Cable from Connector (CN800).  
11. Remove the Touch Pad and Click Button Plate.  
Screws <B>:DRSB2+5FKL  
Screws <C>:DFHE5025XA  
1
7.1.4.  
Removing the Speaker Angle and  
DIMM Lid  
2
<D>  
<D>  
<D>  
<E>  
<E>  
<D>  
DIMM Lid  
Speaker  
Waterproof  
Sheet  
DIMM LID Sheet  
Keyboard  
Speaker Unit  
4. Lift the far side of the Keyboard and slide it to backward,  
and then turn the Keyboard over frontward.  
Speaker Washer  
Speaker Cable  
Tube  
<C>  
Speaker Angle  
Connector (CN37)  
KBD  
Connector  
Cover  
1. Remove the four Screws <D>.  
2. Disconnect the Cable from Connector (CN37).  
3. Remove the DIMM Lid.  
4. Remove the two Screws <E>.  
5. Remove the Speaker Angle.  
5. Remove the three Screws <C>.  
6. Remove the KBD Connector Cover.  
Screws <D>: DRQT2+D2FKL  
Screws <E>: DRHM5025YA  
Keyboard  
7.1.5.  
Removing the Rear Cabinet  
Keyboard  
FPC  
TP Tape  
<F>  
<F>  
<F>  
<F>  
<F>  
Touch Pad  
<F>  
<F>  
<F>  
<F>  
<F>  
Click Button  
Plate  
<F>  
<F>  
<F>  
Connector  
Connector  
(CN800)  
(CN18)  
1. Remove the thirteen Screws <F>.  
2. Open the LID Rubbers.  
3. Remove the Rear Cabinet.  
7. Disconnect the Cable from Connector (CN18).  
8. Remove the Keyboard.  
Screws <F>:DRHM0061ZA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-2  
7.1.6.  
Removing the DU Lid Unit  
7.1.8.  
Removing the Wireless Module,  
Port PCB and Modem  
<G>  
<G>  
<G>  
<G>  
<J>  
<J>  
<G>  
DU LID Angle  
<K>  
<K>  
<I>  
<I>  
<I>  
Modem  
Port PCB  
DU LID  
Bat Con Angle  
Wireless Module  
Connector (J5)  
Connector (J6)  
1. Remove the five Screws <G>.  
2. Remove the DU Lid Angle and DU Lid.  
Note:  
This procedure is not necessary if the computer is not  
equipped with Wireless Module or Modem PCB.  
1. Disconnect the two Antenna Cables from two Connectors  
(J5, J6).  
Screws <G>:DRHM5025YA  
7.1.7.  
Removing the Audio PCB  
Audio PCB  
<H>  
2. Remove the Wireless Module.  
3. Remove the three Screws <I>.  
4. Remove the Port PCB.  
5. Remove the two Screws <J>.  
6. Remove the Modem.  
Connector (CN901)  
7. Disconnect the Modem cable from the connector.  
8. Remove the two Screws <K>.  
9. Remove the BAT CON angle.  
Screws <I>:DRSB2+5FKL  
Screws <J>:XSB2+4FNL  
Screws <K>:DRSB2+5FKL  
7.1.9.  
Removing the SD PCB  
1. Remove the two Screws <H>.  
2. Disconnect the Cable from a Connector (CN901).  
3. Remove the Audio PCB.  
<h>  
<h>  
<h>  
Screws <H>:DRSB2+5FKL  
SD PCB  
Connector (CN21)  
1. Disconnect the Cable from Connector(CN21).  
2. Remove the three Screws <h>  
3. Remove the SD PCB.  
Screws <h>:DXQN2+A22FNL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-3  
5. Remove the two Screws <Q>.  
6. Remove the I/O PCB.  
7.1.10. Removing the Main PCB and Lith-  
ium Battery  
Screws <O>:DFHE5025XA  
Screws <P>:DFHE5058ZB  
Screws <Q>:DRSB2+5FKL  
Lithium Battery  
<M>  
<M>  
<L>  
HDD Guid Plate  
Connector (CN17)  
Connector (CN8)  
Connector (CN3)  
Connector (CN9)  
Connector (CN14)  
LAN Cable  
<N>  
7.1.12. Removing LED PCB and Switch  
PCB  
Connector (CN36)  
<N>  
Connector  
(CN23)  
LED PCB  
LED Waterproof Sheet  
<N>  
Main PCB  
Connector (CN35)  
Connector (CN30)  
Connector (CN12)  
<N>  
Power  
Switch  
Knob  
PCMCIA Unit  
to Connector (CN17)  
to Connector (CN8)  
Switch PCB  
Operation Sheet  
1. Remove the LED Waterproof Sheet.  
2. Remove the LED PCB.  
1. Disconnect the Cable from Connector(CN3).  
2. Remove the Lithium Battery.  
3. Remove the Switch PCB.  
4. Remove the Power Switch.  
3. Disconnect the seven Cables from seven Connectors  
(CN9, CN12, CN14, CN23, CN30, CN35, CN36).  
4. Remove the Screw <L>.  
7.1.13. Removing the CPU Heat Plate  
5. Remove the two Screws <M>.  
6. Disconnect the two Cables from two Connectors (CN8,  
CN17).  
7. Remove the four Screws <N>.  
<R>  
<R>  
<R>  
CPU Heat Plate  
8. Remove the Main PCB.  
9. Remove the PCMCIA Unit.  
Screw <L>:DRSB2+5FKL  
Screws <M>:DXYN2+J12FNL  
Screws <N>:DXYN2+J18FNL  
7.1.11. Removing the PAD PCB and I/O  
PCB  
<O>  
I/O PCB  
<Q>  
<Q>  
<O>  
<O>  
PAD PCB  
Connector  
(CN801)  
1. Remove the three Screws <R>.  
2. Remove the CPU Heat Plate.  
<P>  
Screws <R>:DFHE5025XA  
1. Disconnect the Cable from Connector (CN801).  
2. Remove the three Screws <O>.  
3. Remove the PAD PCB.  
4. Remove the four Screws <P>.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-4  
7.1.14. Removing the Display unit  
7.1.15. Removing the LCD Rear Case  
<S>  
<X>  
<X>  
<S>  
<W>  
LCD Rear Case  
<W>  
<X>  
<X>  
<X>  
<X>  
LCD Hinge Cover  
<X>  
<X>  
Antenna Cover  
<V>  
<V>  
<X>  
<X>  
<V>  
<V>  
<S>  
<S>  
<V>  
<V>  
<V>  
<V>  
1. Remove the four Screws <S>.  
2. Remove the LCD Hinge Cover.  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
Antenna Cover  
<V>  
<V>  
Tablet Latch Cover  
1. Remove the eight Screws <V> on the front side of Display  
unit.  
2. Remove the eight Screws <V> on the back side of Dis-  
play unit.  
3. Remove Antenna Cover and Tablet Latch Cover.  
4. Remove the two Screws <W>.  
5. Remove the ten Screws <X>.  
6. Remove the LCD Rear Case.  
<T>  
Hinge Cover  
<T>  
Screws <V> : DRQT26+E5FKL  
Screws <W> : DXYN3+J10FNL  
Screws <X> : DXYN2+J6FNL  
3. Display unit is half-rotated and removes the two Screws  
7.1.16. Removing the LCD Hinge  
<T>.  
4. Remove the four Screws <U>.  
Cable  
<Y>  
Holder  
Cable  
<Y>  
Plate  
<U>  
<U>  
<U>  
<U>  
Holder  
Plate  
LCD  
Hinge  
Cable  
Holder  
LCD Cable  
Holder  
Sheet  
Cable Holder  
Plate  
Cable  
Holder  
5. Turn the computer over.  
6. Remove the Display Unit.  
Screws <S> : DFHE5025XA  
Screws <T> : DRSB2+5FKL  
Screws <U> : DXYN4+J8FNL  
1. Remove the Cable Holder.  
2. Remove the two Screws <Y>.  
3. Remove the Cable Holder Plate and LCD Hinge.  
Screws <Y> : DXYN3+J8FNL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-5  
7.1.17. Removing Inverter PCB and LCD 7.1.19. Removing the Each Cover  
Unit  
<f>  
Inverter Case  
DC IN LID Rubber  
Connector (CN2)  
USB LID Rubber  
Inverter PCB  
LAN LID Rubber  
Moden/LAN LID Rubber  
Connector (CN1)  
Connector (CN901)  
TS PS2 PCB  
Connector (CN900)  
Audio  
HDD LID ASS’Y  
Battery  
LID Rubber  
<f>  
<f>  
RGB  
LID ASS’Y  
<e>  
LID Rubber  
<e>  
<e>  
<e>  
<f>  
<f>  
<f>  
<f>  
Serial  
LID Rubber  
<e>  
1. Disconnect the two Cables from two Connectors (CN1,  
CN2).  
2. Remove the Inverter Case and Inverter PCB.  
3. Disconnect the two Cable from two connector (CN900,  
CN901).  
PCMCIA LID ASS’Y  
1. Remove the 12 Screws <f>.  
2. Remove the Moden/LAN LID Rubber, LAN LID Rubber,  
USB LID Rubber, DC IN LID Rubber, Serial LID Rubber,  
RGB LID Rubber and Audio LID Rubber.  
3. Remove the Rear Cabinet.  
(Refer to 7.1.5 Removing the Rear Cabinet)  
4. Remove the six Screws <e>.  
4. Remove the TS PS2 PCB, then remove the LCD unit.  
7.1.18. Removing GPRS Antenna PCB,  
LAN1-BT PCB, LAN2-BT PCB, Wide  
Area Aux PCBand Pen Holder  
5. Remove the Battery LID ASS'Y, HDD LID ASS'Y and  
PCMCIA LID ASS'Y.  
<b>  
Wide Area  
Aux PCB  
Pen  
<b>  
Pen Holder  
LAN1-BT  
Antenna PCB  
<a>  
<a>  
<a>  
Screws <e>:DRQT26+D3FKL  
Screws <f>:DRHM5025YA  
<a>  
<a>  
<a>  
LAN2-BT  
Antenna PCB  
<a>  
GPRS  
Antenna PCB  
<a>  
1. Remove the two Screws <a>.  
2. Remove the GPRS Antenna PCB  
3. Remove the two Screws <a>.  
4. Remove the LAN1-BT PCB.  
5. Remove the two Screws <a>.  
6. Remove the LAN2-BT PCB.  
7. Remove the two Screws <a>.  
8. Remove the Wide Area Aux PCB.  
9. Remove the Pen  
10. Remove the two Screws <b>.  
11. Remove the Pen Holder.  
Screws <a> : DFHE5025XA  
Screws <b> : DRHM5025YA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-6  
7.2. Reassembly Instructions  
7.2.1.  
Attention when CF-18 series is repaired  
• Please execute writing BIOS ID when you exchange the Main Board.  
• Parts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.  
7.2.2.  
Setting up the LCD UNIT  
1. Set the LCD UNIT to the LCD FRONT CABINET/TS  
Inverter Case  
Connector (CN2)  
Inverter PCB  
Connector (CN1)  
PANEL.  
2. Fix the LCD Back Damper using the 2 Screws. <Z>  
3. Set the TS PS2 PCB on the LCD Back Damper, and con-  
nect the 2 Cables to the Connectors (CN900 and CN901).  
4. Set the INVERTER PCB to the LCD Back Damper, and  
connect the 2 Cables to the Connectors (CN1 and CN2).  
Connector (CN901)  
TS PS2 PCB  
Connector (CN900)  
Screws <Z> :DXHM0042ZA  
! Assembly of LCD Back Damper (Applicable Model : Touch Screen Model)  
Detail of "B"  
0~1mm  
Detail of "C"  
0~1mm  
Detail of "D"  
0~1mm  
0~0.5mm  
Pass the Cable under  
the protrusion.  
Pass the Cable  
through the space.  
LCD Back Cushion S  
Pass the Cable under  
the protrusion.  
0~0.5mm  
1~1.5mm  
B
LCD Back Cushion L  
C
D
Set the LCD Back Dumper,  
and then screw it.  
Screw<Z>  
Set the LCD Back Dumper,  
and then screw it.  
LCD Back Cushion S  
Detail of "A"  
0~3mm  
Screw<Z>  
A
LCD Back Dumper  
0~0.5mm  
0~0.5mm  
Remove the Release Paper  
on the back side and attach it.  
Crosswise: Match to the middle line.  
Holder Sheet  
Holder Sheet  
Lengthwise: Match to the LCD Frame.  
LCD Back Cushion Side  
0~0.5mm  
LCD Back Cushion Side  
(0~0.5mm)  
(0~0.5mm)  
Hide the hook of the LCD FRAME.  
Hide the hook of the LCD FRAME.  
LCD Side Cushion A  
Attach it to the side surface of the Frame.  
(Match to the end of the Frame  
(0~0.5mm)  
Fit Holder Sheet&LCD Back Cushion Side  
to the leftside end of LCD FRAME.  
(0~0.5mm)  
Fit Holder Sheet&LCD Back Cushion Side  
to the rightside end of LCD FRAME.  
within 0 to 0.5 mm at the far side.)  
LCD PCB SPACER ASSY  
Insert this between LCD PCB & LCD FARME.  
Screw<Z>  
Screw<Z>  
Screw the Board  
Screw the Board  
and the Spacer together.  
and the Spacer together.  
LCD Side Cushion C  
0±0.5mm  
LCD Side Cushion D  
LCD Side Cushion C  
LCD PCB SPACER ASSY  
Spacer Sheet  
LCD PCB Spacer  
Spacer Sheet  
0±0.5mm  
Asymmetric shape  
0±0.5mm  
The form of the left and  
the right isn't symmetrical.  
0±0.5mm  
0±0.5mm  
0±0.5mm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-7  
! Assembly of LCD Back Damper (Applicable Model : Digitizer Model)  
Detail of "A/B/C"  
Pass the Cable  
0~0.5mm  
under the protrusion.  
LCD Back Cushion DG CCFL  
A
B
C
Screw the Digitizer  
Screw the  
and the LCD Back Dumper together.  
Digitizer and  
the LCD Back  
Dumper together.  
Screw  
Screw  
0~3mm  
Digitizer PCB Assy  
LCD Back Dumper  
LCD Back  
Cushion  
DG Side  
Remove the Release Paper on the back side and attach it.  
Lengthwise: Match to the LCD Frame.  
2±0.5mm  
4±0.5mm  
Digitizer  
Crosswise: Match to the middle line.  
Handle it carefully.  
Digitizer PCB Assy  
LCD Side  
Cushion A  
Attach it to the side  
surface of the Frame.  
(Match to the end of  
Digitizer Sheet  
Tape  
2±0.5mm LCD Back Cushion DG Side  
Ensure the  
Connector is  
connected  
securely.  
Fold back the half length,  
and attach to the LCD side.  
0~0.5mm  
10±2mm  
the Frame within 0 to 0.5 mm  
at the far side.)  
10±2mm  
0~0.5mm  
Fold back the surplus length.  
Screw the Board together.  
Screw  
Screw the Board together.  
Screw  
0±0.5mm  
0±0.5mm  
LCD Side Cushion D  
LCD Side Cushion C  
0±0.5mm  
LCD Side  
Cushion C  
0±0.5mm  
0±0.5mm  
0±0.5mm  
! Assembly of Inverter PCB (Applicable Model : Touch Screen Model)  
Safety Working  
LCD Side Cushion E  
Prevent FPC from coming off.  
Avoid any stress on the Cable  
when connecting it  
Insert between  
the ribs.  
Insulation Parts  
12  
Connector  
to the Inverter.  
LCD Side Cushion E  
Insert between the ribs.  
PWB  
FPC  
(Hold the Connector part  
when connecting  
/disconnecting.)  
Caution High  
Voltage Label  
LCD Side Cushion F  
TS PWB  
Insert between the ribs.  
Insert  
0~3mm  
Inverter Assy  
0~0.5mm  
Connect the Cable to the left  
and right Connectors.  
PET TAPE 1  
Tape  
Inverter Assy  
Avoid any stress on the Cable  
Attach so the Inverter Assy  
comes at the center,  
and attach the left and right  
LCD REAR Side  
when connecting it to the Inverter.  
(Hold the Connector part  
Pay attention to the direction of  
the INVERTER PCB when doing  
this installation.  
when connecting/disconnecting.)  
surplus length to the Back Dumper  
as illustrated below.  
LCD Cable  
INV MIL Sheet  
Carefully attach Tape  
Tape  
Safety Working  
30~35mm  
Sield Sheet  
pasted on the connector  
after it is wound around  
the cable twice.  
Inverter Assy  
LCD Back Dumper  
Inverter Case MIL  
Insulation Parts  
Fix the two Cables.  
("Gap side" is front.)  
INV MIL Cover  
0~3mm  
Avoid getting under the Sheet.  
INV Sheet 1  
(Black)  
Detail of "A"  
Safety Working  
6–2mm from  
the branch point  
A
Confirm a "Insulation  
Parts" isn’t frayed.  
Insert  
5~6mm  
LCD Cable Connector side  
Inverter  
Insert  
Conductive Tape  
ANT Cable Cushion  
Wrap.  
CCFL  
Don’t give stress to LCD TAB.  
Wrap over the Antenna Cable  
Cushion and the Cable.  
Connector  
5~6mm  
side  
1~2  
mm  
INV Sheet 2  
(Translucence)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-8  
! Assembly of Inverter PCB (Applicable Model : Digitizer Model)  
Safety Working  
Avoid any stress on the Cable  
when connecting it to the Inverter.  
(Hold the Connector part  
Avoid any stress on the Cable  
when connecting/disconnecting.)  
when connecting it to the Inverter.  
(Hold the Connector part  
when connecting/disconnecting.)  
LCD Side Cushion E  
Insert between the ribs.  
LCD Side Cushion F  
Insert between the ribs.  
LCD Side Cushion E  
Insert between  
the ribs.  
Caution High Voltage Label  
0~3mm  
Tape  
Inverter Assy  
Attach so the Inverter Assy  
comes at the center.  
Connect the Cable to the left  
and right Connectors.  
Inverter Assy  
(Top/Bottom: -2 to +2 mm,  
Left/Right: -3 to +3 mm)  
LCD Rear Side  
Carefully attach Tape.  
Pay attention to the direction of  
the INVERTER PCB when doing  
this installation.  
Tape  
0~0.5mm  
PET Tape2  
Inverter Assy  
LCD Back Dumper  
Sield Sheet  
LCD Cable  
Match to the  
Inverter  
Case MIL  
left end of  
the square  
hole of the  
Connector.  
pasted on the connector  
after it is wound around  
the cable twice.  
0~0.5mm  
Safety Working  
INV MIL Cover  
Insulation Parts  
0~3mm  
5~6mm  
Detail of "A"  
Safety Working  
Confirm a  
"ANT Cable Cushion"  
isn’t frayed.  
Avoid getting under the Sheet.  
Insert  
Insert  
6–2mm from  
the branch point  
A
LCD Cable  
Connector side  
INV Sheet 1 Inverter  
(Black)  
5~6mm  
Conductive Tape  
INV Sheet 2(Translucence)  
Don’t give stress to LCD TAB.  
Avoid any stress on the TAB  
part of the LCD Module.  
ANT Cable Cushion  
Wrap.  
CCFL Connector side  
1~2  
mm  
Wrap over the Antenna Cable  
Cushion and the Cable.  
! Assembly of Touch Screen (Applicable Model : Touch Screen Model)  
Detail of "A"  
Back side  
A
Touch Screen Assy  
6–0.5mm  
Protect Sheet  
Remove it parallel to the Touch Screen.  
TS FPC  
Spacer  
Attach the surface  
at the center of  
the display.  
OK  
Laminate film  
(Using the jig)  
Dimensional tolerance  
:–0.2  
Touch Sreen  
Laminate film  
NG  
0~0.5mm  
Touch Sreen  
Touch  
Screen  
0~0.5mm  
Place this to the wall of cabinet.  
TS Spacer A  
0~1mm  
0~1mm  
Attach the surface to the LCD Front.  
–0.5mm  
Fit this to the  
line of cabinet.  
TS Spacer B  
TS Spacer B  
LCD Side  
Cushion B  
Be free of overhang..  
TS Spacer A /TS Spacer B:  
Don’t get into a LCD indication range.  
TS Spacer A  
0~1mm  
Touch Screen Assy  
0~1mm  
–0.5mm  
Fit this to the  
line of cabinet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-9  
! Assembly of Glass (Applicable Model : Digitizer Model)  
Glass Assy  
AR Film  
Attach so it comes at the center part  
when the LCD Unit is completely assembled.  
Protection Sheet  
Attach it to the front side. (Using the jig)  
Paste this to frontside.  
Attach it to the back side.  
(Using the jig)  
Paste this to backside.  
Attach it at the center.  
Dimensional tolerance:  
Detail of "A"  
Attach it at the center.  
Dimensional tolerance:  
0~0.5mm  
–0.2  
–0.2  
0.5~1.0mm  
Glass (Digitizer)  
TS Spacer A  
0~0.5mm  
Place this to the wall of cabinet.  
A
0.5~1mm  
Attach the surface to the LCD Front.  
–0.5mm  
Fit this to the  
line of cabinet.  
TS Spacer B  
TS Spacer B  
0.5mm  
LCD Side  
Cushion B  
Be free of overhang..  
TS Spacer A / TS Spaser B:  
Don’t get into a LCD indication range.  
0.5mm  
Glass Assy  
TS Spacer A  
0.5~1mm  
–0.5mm  
Fit this to the  
line of cabinet.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-10  
7.2.3.  
Assembling GPRS Antenna PCB, LAN1-BT PCB, LAN2-BT PCB, Wide Area Aux  
PCB, and Pen Holder  
1. Fix the Pen Holder using the 2 Screws. <b>  
<b>  
Wide Area  
Aux PCB  
2. Fix the Wide Area Aux PCB using the 2 Screws. <a>  
3. Fix the LAN2-BT PCB using the 2 Screws. <a>  
4. Fix the LAN1-BT PCB using the 2 Screws. <a>  
5. Fix the GPRS Antenna PCB using the 2 Screws. <a>  
Pen  
<b>  
Pen Holder  
LAN1-BT  
Antenna PCB  
<a>  
<a>  
<a>  
<a>  
Screws <a> : DFHE5025XA  
Screws <b> : DRHM5025YA  
<a>  
<a>  
LAN2-BT  
Antenna PCB  
<a>  
GPRS  
Antenna PCB  
<a>  
! Line processing of Antenna Cable  
Safety Working  
Detail of "B"  
Detail of "A"  
Safety Working  
Be free of overhang..  
Be free of overhang..  
B B  
A
Screw<a>  
Screw<a>  
Cable Cushion  
GPRS Antenna PCB  
Bundle and wind 3 cables.  
Safety Working  
LAN1-BT  
Antenna PCB  
Cable Cushion  
Insert this between two ribs after pasting  
Cable Cushion.  
Be free of overhang..  
Detail of "D"  
Screw<a>  
Screw<a>  
Insert cables between four pins.  
Hook it.  
Screw<a>  
Screw<a>  
Wide Area Aux  
PCB  
Attach it to the inner  
side of the right rib.  
Cable Cushion  
LAN2-BT Antenna PCB  
Screw<a>  
Screw<a>  
Detail of "C"  
C
0~1mm  
0–3mm  
Be free of overhang..  
D
Ensure the white Cable is coming out  
by 31 cm or more from the right edge (  
of the Front Case.  
More than 31cm from  
)
Sheet(For EMI)  
Tape  
Bundle and wind 2 cables.  
Safety Working  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-11  
7.2.4.  
Setting up the LCD Hinge  
1. Wind the Cable coming out of the LCD Unit conterclock-  
Cable  
Holder  
Plate  
<Y>  
wise to the LCD Hinge.  
Cable  
Holder  
Plate  
<Y>  
2. Set the Lock Plate and the Hinge Top Cover, and rotate  
the LCD Hinge to turn the Display Unit to front  
3. Put the LCD Cable and the Antenna Cable in the Cable  
Holder.  
LCD  
Hinge  
Cable  
Holder  
4. Fit another Cable Holder and clamp the Cable Holders in  
the LCD Hinge.  
5. Fix the LCD Hinge using the 2 Screws <Y> and the 2  
Cable Holder Plates.  
LCD Cable  
Holder  
Cable Holder  
Plate  
Sheet  
Cable  
Holder  
Screws <Y> : DXYN3+J8FNL  
! Assembly of LCD Hinge  
Safety Working  
Ensure the "C" side  
comes to the lower  
right corner when  
Ensure it comes  
over the Cable Hold Tape.  
Not necessary if the Cable  
is not passed under  
the Cable Hold Plate.  
viewing from above.  
A
Cable Hold Plate  
Safety Working  
Avoid catching the Cable.  
Be free of pinching cables.  
Avoid running over  
Screw<Y>  
Screw<Y>  
LCD Hinge  
A
the Hinge and the rib.  
Cable Hold Plate  
Using the fixing jig when fixing the Hinge  
Tighten.  
Initial condition of LCD Hinge.  
Tighten.  
Fix.  
Avoid catching the Cable (when repairing or when not using the jig).  
Temporarily fix the both sides ("A") of the Hinge using  
the Screw <W>, and fix the Cable Hold Plate.  
After fixing the Cable Hold Plate, remove the Screw <W>  
from the both sides ("A").  
Cable Hold Plate is installed after it is kept in A  
If you arrange the Cable in the area,  
you do not need to use the fixing jig.  
The direction which can rotate  
temporarily.(using Screw<W>)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-12  
! Line processing of Antenna Cable and LCD Cable  
Safety Working  
Pinch and curl it in the arrow  
direction to avoid coming off.  
Cable  
You will hear the sound when they are firmly jointed.  
Holder  
Allow some cable margin.  
LCD  
Cable  
Holder  
Sheet  
LCD Cable Holder  
Sheet  
ANT Cable  
LCD Front side  
Turn the Cable  
360 degree.  
Direction of rotation  
Lock Plate  
Assy  
Wind antena cables first.  
Lock Spring Lock spring is inserted,  
LCD Rear Side  
Cable Holder  
Hinge Cover Assy  
and Lock plate is inserted more.  
Pass the Cables through it,  
and then fix it to the Hinge.  
(Fix directly the other side.)  
For fixing, hold the Hinge parallel to the LCD.  
Parallel with LCD  
RELEASE  
Cable Stopper Tape  
HIinge Cover  
Cable Stopper Tape  
Release Label  
Fit it to the concave portion.  
* Avoid running over the parts.  
LCD Cable  
Pull and hold the LCD Cable, and attach the Tape.  
(Wrap the LCD Cable only.)  
Protect Sheet  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-13  
7.2.5.  
Assembling the Anntena Cover, the Tablet Latch Cover and the LCD Rear Case  
1. Fix the LCD Rear Case using the 10 Screws <X> and the  
<X>  
2 Screws <W>.  
2. Attach the Antenna Covers and the Tablet Latch Cover to  
the Display Unit.  
3. Tighten the 8 Screws <V> on the back of the Display Unit.  
4. Turn the Display Unit over, and tighten the 8 Screws. <V>  
<X>  
<W>  
LCD Rear Case  
<W>  
<X>  
<X>  
<X>  
<X>  
Screws <V> : DRQT26+E5FKL  
Screws <W> : DXYN3+J10FNL  
Screws <X> : DXYN2+J6FNL  
<X>  
<X>  
Antenna Cover  
<V>  
<V>  
<X>  
<X>  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
<V>  
Antenna Cover  
<V>  
<V>  
Tablet Latch Cover  
! Assembly of LCD Front Case  
LCD Front Assy  
Magnet Assy  
Magnet Tape  
0~0.5mm  
Magnet  
0~1mm  
–1mm (Both on the top and the side)  
Be free of overhang..  
Be free of overhang.  
Be free of overhang..  
TS Tape  
Note for attachment  
Ensure it does not come over the display part.  
Don’t get into a LCD indication range.  
Attach and apply the load 30 to 40N (3.0 to 4.0 Kgf).  
Position of pasting TS Tape.  
0~0.5mm  
Place this to the ribs.  
0~0.5mm  
0~0.5mm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-14  
! Assembly of LCD Rear Case (Applicable Model : Touch Screen Model)  
LCD Rear Cushion F  
LCD Rear Cushion A  
LCD Rear Cushion F  
LCD Rear Cushion F  
LCD Rear Cushion A  
0–0.5mm  
Marking line  
–0.5mm  
Attach it between the marking lines.  
0~5mm  
LCD Rear Cushion G  
Marking line  
–0.5mm  
0~5mm  
Shift it to the center side by  
0 to 1 mm from one of the lines.  
Marking line  
–0.5mm  
0~5mm  
0~5mm  
LCD Rear Assy  
LCD Rear Cushion G  
0~5mm  
LCD Rear Cushion B  
0~5mm  
Marking line  
–0.5mm  
LCD Rear Cushion B  
Marking line  
–0.5mm  
LCD Rear Cushion C  
LCD Rear Cushion C  
Marking line  
0~1mm  
0~5mm  
0~5mm  
0~5mm  
LCD Rear Cushion E  
LCD Rear Cushion D  
LCD Rear Cushion E  
! Assembly of LCD Rear Case (Applicable Model : Digitizer Model)  
LCD Rear Cushion A  
LCD Rear Cushion F  
LCD Rear Cushion A  
LCD Rear Cushion F  
LCD Rear Cushion F  
0–0.5mm  
0~5mm  
Marking line  
–0.5mm  
Marking line  
–0.5mm  
fitted the center  
Attach it between the marking lines.  
LCD  
Rear  
Shift it to the center side  
by 0 to 1 mm from one of the lines.  
Cushion C  
Marking line  
–0.5mm  
0~5mm  
0~5mm  
LCD Rear Assy  
Marking line  
–0.5mm  
LCD  
Rear  
Cushion B  
LCD  
Rear  
Cushion B  
LCD  
Rear  
Cushion C  
0~5mm  
0~5mm  
0~5mm  
0~3mm  
LCD  
Rear  
Cushion C  
LCD Rear Cushion D  
LCD Rear Cushion E  
LCD Rear Cushion E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-15  
! Assembly of Tablet Latch Cover and Antenna Cover  
Tablet Lacth Cover  
Press and hold it against the cabinet,  
and fix it using the Screw.  
ANT Cover  
Press and hold it against the cabinet,  
and fix it using the Screw.  
Places of tighten a screws  
10 Places  
Screw<X>  
ANT Cover  
Press and hold it  
against the cabinet,  
and fix it using the Screw.  
16 Places  
Screw<V>  
in numerical order  
(same the frontside)  
Don’t forget screws  
Screw<W>  
Screw<W>  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-16  
7.2.6.  
Setting the Display Unit  
1. Fix the Display Unit using the 2 Screws <T>.  
3. Turn the computer over and fix the LCD Hinge Cover  
using the 2 Screws <S>.  
4. Open the Display Unit and fix the LCD Hinge Cover using  
the 2 Screws <S>.  
Screws <S> : DFHE5025XA  
Screws <T> : DRSB2+5FKL  
Screws <U> : XYN4+J8FNL  
<T>  
Hinge Cover  
<T>  
<S>  
<S>  
LCD Hinge Cover  
2. Close the Display Unit and turn the computer over, and  
then fix the Display Unit using the 4 Screws <U>.  
<U>  
<U>  
<U>  
<U>  
<S>  
<S>  
! Assembly of Display Unit  
Safety Working  
Note  
Screw<U>  
Screw<U>  
Screw<U>  
Screw<U>  
Avoid any stress on the Cable.  
Detail of "A"  
Hinge Cover  
< Order of fixing screw>  
Cable  
Cushion  
LCD Cable  
white/black  
blue/ glay/brown  
Close the LCD and  
turn it over.  
LCD UNIT  
Top Case Assy  
Take out the Cables.  
A
Pass all of the Cables into the KBD Hole.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-17  
7.2.7.  
Setting the CPU Heat Plate  
1. Fix the CPU Heat Plate using the three Screws<R>.  
<R>  
<R>  
<R>  
Screws <R>:DFHE5025XA  
CPU Heat Plate  
! Line Processing of the Modem Cable, and putting of the Heatsink Rubber.  
MODEM Cable  
Attach the PET Tapes on the both sides  
to completely cover the thin cable.  
Modem Cable  
MODEM Cable  
0~1mm  
Sub material:  
PET TAPE 2  
0~1mm  
(10 mm width x 3 cm)  
Heatsink Rubber  
0~0.5mm  
5~0.5mm  
0~1mm  
Tape  
0~1mm  
0~0.5mm  
Tape  
0~0.5mm  
Cover the  
hole.  
Lead the Cable along the surface.  
0~1mm  
Safety Working  
0~1mm  
Sub material:  
PET TAPE 2  
(10 mm width x 3 cm)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-18  
7.2.8.  
Setting the LED PCB and the Switch PCB  
1. Set the Power Switch.  
2. Set the Switch PCB.  
LED PCB  
LED Waterproof Sheet  
3. Set the LED PCB.  
4. Attach the new LED Waterproof Sheet.  
Power  
Switch  
Knob  
Switch PCB  
Operation Sheet  
! Assembly of the LED PCB and the Switch PCB  
LED PCB  
LED PCB Tape  
Ensure it does not come  
0~5mm  
over the end of the Board by 0.5 mm or more.  
Back side  
LED Light Guide Sheet  
Avoid running over the LED.  
0~3mm  
Sub material:  
PET TAPE 1  
(19 mm width x 3 cm)  
Connector surface  
Fold back and attach.  
Allowable misalignment  
of the edges  
LED FFC  
SW PCB  
0~1.5mm  
Operation Tape  
Match the frame  
edges  
Confirm the direction  
when attaching.  
CN bracket is on the back side.  
and attach them.  
Avoid coming  
off of the LED part,  
or running over the LED part.  
Operation Sheet  
SW PCB  
Perform the operation check for a few times,  
and ensure the smooth operation without noise.  
Power SW Knob  
Match to the upper left corner.  
0 to 0.5 mm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-19  
7.2.9.  
Setting the PAD PCB and the I/O PCB  
1. Fix the I/O PCB using the four Screws<P> and the two  
<O>  
<O>  
I/O PCB  
<Q>  
Screws<Q>.  
<Q>  
<O>  
PAD PCB  
2. Fix the PAD PCB using the three Screws<O>.  
3. Connect the SW Cable to the Connector (CN801) of the  
PAD PCB.  
Connector  
(CN801)  
<P>  
Screws <O>:DFHE5025XA  
Screws <P>:DFHE5058ZB  
Screws <Q>:DRSB2+5FKL  
! Assembly of PAD PCB  
Sub material:  
PET TAPE 1  
(19 mm width x 3 cm)  
For models with  
measures against  
whiskers, use  
the Tape of  
PAD PCB  
0~1mm  
19 mm width x 2 cm  
Fold back and attach.  
Allowable misalignment  
of the edges  
0~1.5mm  
FFC CN Stopper  
Match to the center  
of the Connector.  
PAD FFC  
Connector surface  
SW FFC  
Connector surface  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-20  
! Putting of the PAD Insulation Sheet  
TOP Case Assy  
0~0.5mm  
Front side  
TP Bottom Tape  
Right side  
Don’t overflow.  
Core side  
PAD Card Insulation Sheet  
Core side  
0~0.5mm  
! Assembly of TOP CASE ASSY  
Remove the Release Paper  
and attach it to the Top Case.  
Kensington Plate  
0~0.5mm  
0~0.5mm  
0~0.5mm  
Kensington Plate  
Tape  
0~0.5mm  
0~0.5mm  
Kensington Lock Plate  
Keep the 1 mm space between  
the Top Case and the rib.  
Gasket  
0~0.5mm  
Gasket  
Attach to the indent portions  
for the USB.  
Touch PAD  
Remove the Release  
Paper and attach it.  
After attaching it,  
HDD Side Spacer  
connect to the Connector.  
Attach here.  
(0 ~ 0.3mm)  
LED PCB  
Fit it to the pin  
and attach it.  
0~0.5mm  
0~0.5mm  
0~0.5mm  
0~0.5mm  
Safety Working  
Screw  
PAD PCB  
Check a lock after the insertion  
SW Spring  
Detail of "A"  
Click Button Sheet  
Avoid running over the side.  
Apply the load to attach.  
30 to 40N (3.0 to 4.0Kgf)  
Check a lock after the insertion  
A
After connecting the FFC  
Details of cable arrangement  
PCMCIA Cushion  
Hook on the protrusions of the boss and the Power Switch.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-21  
7.2.10. Setting the Main PCB and the Lithium Battery  
1. Set the PCMCIA Unit to Main PCB  
Lithium Battery  
<M>  
<M>  
2. Mount the HDD Guide Plate and set the Main PCB.  
3. Fix the Main PCB using the four Screws <N> and the two  
Screws <M>.  
<L>  
HDD Guid Plate  
Connector (CN17)  
Connector (CN8)  
Connector (CN3)  
Connector (CN9)  
Connector (CN14)  
LAN Cable  
<N>  
4. Fix the Main PCB using the Screw <L>.  
5. Connect the seven Cables to the corresponding Connec-  
tors (CN9,CN12,CN14,CN23,CN30,CN35,CN36).  
Connector (CN36)  
<N>  
6. Turn the computer over and connect the two Cables to  
the corresponding Connectors (CN8, CN17).  
7. Connect the Cable to the Connector (CN3), and fix the  
Lithium Battery.  
Connector  
(CN23)  
<N>  
Main PCB  
Connector (CN35)  
Connector (CN30)  
Connector (CN12)  
<N>  
Screw <L>:DRSB2+5FKL  
Screws <M>:DXYN2+J12FNL  
Screws <N>:DXYN2+J18FNL  
PCMCIA Unit  
to Connector (CN17)  
to Connector (CN8)  
! Line Processing of the Antenna Cable  
Tape  
Use the Tape only for  
the position with the  
Antenna Cable.  
Avoid running over  
the Connector  
Draw it out of the cabinet.  
Antenna Cable (Gray)  
If no Gray Cable, use  
the Brown Cable.  
Draw it out of the cabinet.  
Antenna Cable  
(black)  
and the bis.  
Antenna Cable  
(blue)  
Screw  
Screw  
Sub material:  
PET TAPE 1  
(19 mm width x 3 cm)  
CPU Heat Plate  
Pass it between  
the bosses.  
Sub material is not  
necessary if the Tape  
and the Cable Holder  
(CAP) are not used.  
Heat Dissipation  
Rubber  
0~2mm  
Arrange the Cables,  
and then set it.  
Tape  
Avoid running  
over the boss.  
0~2mm  
Cable Holder(Cap)  
0~1mm  
Pass it beside  
0~1mm  
Draw it out of the cabinet.  
Tape  
)
the pin.  
Details for attachment  
1~2mm  
Antenna Cable  
(white)  
Safety Working  
Draw it out of the cabinet.  
Attach as shown above  
to avoid coming off.  
Screw  
Heat Dissipation Rubber  
Match the left end to the marking line.  
Fit it lengthwise in the frame.  
(0 to 0.5 mm from the  
end of the cabinet)  
Check a position of  
power swich knob.(right)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-22  
! Line Processing of Main Unit  
Screw(D Sub)  
Screw  
Screw  
I/O PCB ASSY  
Screw  
Tape  
Safety Working  
Connect.  
Insert the surplus  
length between the Modem  
Connector and  
Safety Working  
the LAN Connector.  
Screw  
Modem  
Connector  
HDD Guide Plate  
When inserting,  
use the jig to receive  
the Cable.  
Screw  
Between the Main Board  
and the Top Case  
LAN  
Connector  
MAIN PCB  
White  
Avoid running over  
the Modem Connector  
and the LAN Connector  
(yellow area).  
Screw  
Connect it first when  
setting the Main Board.  
Then attach the Coin Battery  
to the Top Case.  
0~0.5mm  
Bat Cushion  
Screw  
0~2mm  
FFC CN  
Stopper  
MAIN PCB  
Main PCB Switch  
Bat Con Angle  
0~0.5mm  
Connect the FFC.  
Match to  
the edge  
of the  
Attach before  
setting  
the Main PWB.  
Tape  
Board.  
Screw  
Wipe off using alcohol  
before attaching.  
After connecting  
the FFC, shape  
it over the Board.  
Then insert the  
shaped part to the  
BAT Connector.  
FFC Spacer  
! Line Processing of the Lithium Battery  
Lithum Battery  
Connect the Cable to the Connector CN3 of the Board.  
(Right angle type)  
After attaching the Cushion for Lithum Battery,  
set the Lithum Battery as shown below.  
CN3  
Safety Working  
Attach the Lithum Battery on the Cushion.  
Draw the Lead Wire toward the end of the Board.  
Arrange the surplus length of the Lead Wire  
as shown below.  
Cushion for Lithum Battery  
Attach on the IC14 (Super I/O).  
Attach the white adhesive surface to the IC side.  
Pass the Lead Wire through  
the notch of the Board.  
End of the Board.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-23  
7.2.11. Setting the SD PCB  
1. Fix the SD PCB using the three Screws <h>.  
2. Connect the Cable to the Connector (CN21).  
<h>  
<h>  
<h>  
Screws<h>:DXQN2+A22FNL  
SD PCB  
Connector (CN21)  
! Assembly of SD PCB  
SD ANGLE Assy  
0~0.5mm  
SD Angle  
Spacer 2  
0~0.5mm  
0~0.5mm  
0~0.5mm  
SD Angle  
SD Angle Spacer 1  
0~0.5mm  
Insert it into the boss  
as it comes over the Cable.  
Cable Holder Sheet  
0~0.5mm  
Screw  
Screw  
Screw  
SD PCB  
Avoid running  
over the positioning  
pin of the SD Angle.  
Screw  
Only for the Antenna Cable  
Insert the surplus length  
under the Board.  
SD ANGLE  
ASSY  
Do not insert the Coin  
Battery Cable underthe Board.  
FFC  
Avoid running  
over the Cable.  
Sub material:  
PET TAPE 2  
0~3mm  
(10 mm width x 3 cm)  
Do not bend on the stiffening plate.  
(Bend it at 1 mm away  
from the stiffening plate.)  
Note for cable  
arrangement  
DIMM Holder  
Set the SD Board and then connect  
to the DIMM Connector.  
*Before connecting, confirm  
the Spacer is not attached  
on the Main Board.  
Not necessary for model  
without the Antenna Cable  
0~0.5mm  
Only for model with DIMM  
Release the Hooks  
on the both sides  
before setting the DIMM Holder.  
SD Sheet  
0~0.5mm  
Two-sided tape  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-24  
7.2.12. Setting the Wireless Module, the Port PCB, and the Modem  
1. Fix the Battery Connect Angle using the two Screws <K>.  
2. Connect the Modem cable to the Connector, and fix the  
<J>  
<J>  
Modem on the Main PCB using the two Screws <J>.  
3. Fix the Port PCB on the Main PCB using the three  
Screws <I>.  
4. Connect the Wireless Module to the Main PCB, and con-  
nect the two Antenna Cables (J5, J6) to the Wireless  
Module.  
<K>  
<K>  
<I>  
<I>  
<I>  
Modem  
Port PCB  
Bat Con Angle  
Wireless Module  
Screws <I>:DRSB2+5FKL  
Screws <J>:XSB2+4FNL  
Screws <K>:DRSB2+5FKL  
Connector (J5)  
Connector (J6)  
! Assembly of the Port PCB  
Portre Sheet  
Ensure it does not come  
over the end of the Board  
by 0.5 mm or more.  
Port PCB  
Ensure the Board does not  
run over the dowel.  
0~0.5mm  
0~0.5mm  
DU Connetor Angle  
Match the center of the Sheet  
to the end of the DU Connector.  
(-1 to +1 mm)  
Tape  
Attach the surplus  
Back side  
length to the edge of the Board.  
DU Sponge B  
Antenna PCB  
DU Sponge  
D
Match to the center  
of the Board.  
0~0.5mm  
(-1 to +1 mm)  
0~0.5mm  
0~0.5mm  
Match to the center  
of the Board.  
(-1 to +1 mm)  
DU Sponge B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-25  
! Line Processing of the Wireless Module,Port PCB and Modem  
Insert it into the boss  
as it comes over the Cable.  
Cable Holder Sheet  
Details of cable  
arrangement  
Tape  
Safety Working  
DU PCB ASSY  
Safety Working  
1
Pass it under the Coin  
Battery Cable and fix it.  
Pass the Cable  
under the card.  
Tape up  
to the  
far side.  
Cable  
Details of cable  
arrangement  
Insert the end of the Sheet  
into the space between the Main Board  
and the bottom of the LAN Connector.  
0~0.5mm  
0~0.5mm  
..  
Pass the Black Cable over  
the Gray Cable and connect  
them. Draw them sideways  
in parallel as shown above.  
Side surface  
PCMCIA Sheet  
Wind the coil  
securely to avoid  
coming off.  
Pass it at the right of the Coil.  
Sub material:  
Safety Working  
PET TAPE 1  
(19 mm width x 4 cm)  
Modem Cable  
0~1mm  
DU Sponge A  
0~1mm  
0~0.5mm  
Screw  
Pass the Cables through the notch  
of the Board.  
0~0.5mm  
DU Sponge C  
0~0.5mm  
*Do not bend sharply.  
Avoid rubbing against the Board  
and damaging of the Cable.  
Tape  
Attach the insulation sheet  
for the Modem Cable.  
Remove the Modem PCB before using  
the Tape and the Screw.  
Mini PCI Card Sheet  
Ensure it is set  
in the Hooks  
Screw  
on the both sides  
of the receiving Connector.  
5–2mm  
(Not necessary for model  
without W-LAN Module)  
Fold back and attach.  
Gasket  
Sub material:  
1~2mm  
PET TAPE 1  
(19 mm width x 4 cm)  
1~2mm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-26  
7.2.13. Setting the Audio PCB  
1. Connect the Cable to the Connector of the Audio PCB  
(CN901), and fix the Audio PCB using the two  
Screws<H>.  
Audio PCB  
<H>  
Screws<H>:DRSB2+5FKL  
Connector (CN901)  
! Putting of the Sheet  
Confirm the direction of the FFC when connecting.  
Connector surface  
Sheet(for EMI)  
Audio PCB  
Back side  
Attach it along the  
surface of the Connector  
and the FPC.  
Audio FFC  
Ensure it does  
not run over  
the Connector  
Sub material:  
by 0.1 mm or more.  
PET TAPE 1  
(19 mm width x 5.5 cm)  
7.2.14. Assembling the DU Lid Unit  
1. Fix the DU Lid Angle and the DU Lid using the five  
Screws<G>.  
<G>  
<G>  
<G>  
<G>  
Screws <G>:DRHM5025YA  
<G>  
DU LID Angle  
DU LID  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-27  
7.2.15. Setting the Rear Cabinet  
1. Fix the Rear Cabinet on the computer using the 13  
Screws <F>. No1 to No13  
2. Close the LID Rubbers.  
Note:  
<F>:No3  
<F>:No11  
<F>:No7  
<F>:No9  
<F>:No12  
<F>:No2  
Tighten the Screws in the numbered order (No1 to No13).  
<F>:No10  
<F>:No5  
Screws<F>:DRHM0061ZA  
<F>:No13  
<F>:No1  
<F>:No6  
<F>:  
No8  
<F>:No4  
! Cautions for Setting the Rear Cabinet  
Bottom Rubber  
DU Stopper  
Tape  
Potre Blind Sheet  
Bottom Rubber  
Safety Working  
0~1mm  
0~1mm  
DU Sponge  
Tape  
0~0.5mm  
0~0.5mm  
Information Label  
0~0.5mm  
0~0.5mm  
Note for attachment  
:
Avoid running over the frame.  
Avoid air leaking into it.  
SD Under Spacer  
Spacer Spacer  
0~0.5mm  
Bottom Rubber  
0~1mm  
Match to the  
center of the  
Screw hole.  
Bottom Rubber  
Bottom Case Assy  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-28  
7.2.16. Setting the Speaker and Dimm Lit  
1. Fix the Speaker Angle to the DIMM Lit using the two  
Screws <E>.  
<D>:No1  
2. Connect the Speaker Cable to the Connector (CN37) of  
the Main PCB.  
3. Fix the DIMM Lit using the four Screws<D>. No1 to No4  
<D>:  
No4  
<D>:No3  
<D>:  
No2  
<E>  
DIMM Lid  
DIMM LID Sheet  
<E>  
Speaker  
Screws<D>:DRQT2+D2FKL  
Screws<E>:DRHM5025YA  
Waterproof  
Sheet  
Speaker Unit  
Speaker Washer  
Speaker Cable  
Tube  
Speaker Angle  
Connector (CN37)  
! Cautions for Setting the DIMM Lit  
DIMM Lid Assy  
DIMM Thermal Rubber  
Allowable  
right/left  
displacement:  
max. 1 mm  
DIMM Lid  
Confirm the direction  
of the Connector  
when connecting.  
Avoid catching  
the Cable.  
Safety Working  
When removing the Bottom Case Assy,  
be sure to remove the DIMM Lid Assy.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-29  
7.2.17. Setting the Touch Pad and the Keyboard  
1. Connect the Cable to the Connector (CN800), and attach  
the Touch Pad to the computer.  
7. Set the Keyboard to the computer.  
2. Set the Click Button Plate.  
3. Attach the new TP Tape over the Touch Pad.  
4. Attach the Palm Rest Ass'y on the computer.  
2
1
Palm Rest Ass’y  
TP Tape  
Touch Pad  
Keyboard  
8. Fix the KBD Plate using the four Screws<B>.  
Click Button  
Plate  
Screws<B>:DRSB2+5FKL  
Screws<C>:DFHE5025XA  
KBD Plate  
<B>  
Connector  
(CN800)  
<B>  
KBD Plate  
<B>  
5. Connect the Cable of the Keyboard to the Connector  
(CN18) on the Main PCB.  
<B>  
6. Fix the KBD Connector Cover using the three  
Screws<C>.  
<C>  
KBD  
Connector  
Cover  
Keyboard  
Connector  
(CN18)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-30  
! Putting of the Sheet  
GASKET E  
Fit the surplus length into  
the groove of the Hinge.  
LCD Cushion Sheet  
LCD Cushion Sheet  
Ensure it does not come over  
the end of the rib.  
Ensure it does not  
come over the end  
of the rib.  
0~0.5mm  
0~0.5mm  
0~0.5mm  
0~0.5mm  
KBD Waterproof Sheet R  
0~1mm  
Avoid coming over.  
0~0.5mm  
0~0.5mm  
KB CNT Hole  
Cushion  
0~0.5mm  
Match to the circles.  
Match to the circles.  
0~0.5mm  
0~0.5mm  
KBD Waterproof Sheet L  
KBD Waterproof Sheet C  
Avoid coming over.  
0~0.5mm  
Avoid coming over.  
0~0.5mm  
Avoid coming over.  
0~0.5mm  
Avoid running over.  
0.5~1mm  
Avoid running over.  
0.5~1mm  
Click Button Plate  
0~0.5mm  
0~0.5mm  
TP Tape  
Avoid coming over.  
0~0.5mm  
0.5~1.5mm  
0.5~1.5mm  
Palmrest Sheet R  
LED Waterproof Sheet  
Tape  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-31  
! Cautions for Setting the Keyboard  
Keyboard  
KBD Connector Cover  
LCD CABLE  
Apply the load to attach. 30 to 40N  
(3.0 to 4.0 Kgf)  
Keyboard  
KBD Tape  
KBD Connector Cover  
KBD Tape  
Connect the Connector to the part  
with dotted frame.  
(Note  
Lengthwise:  
KBD Tape  
0–0.5mm  
Hold the Connector part when  
connecting/disconnecting.  
Do not bend at the foot  
of stiffening plate.)  
Match to the center line.  
Crosswise:  
Lengthwise:  
Match to the end of the KBD.  
Match to the center line.  
Crosswise:  
8~  
10mm  
Match to the end of the KBD.  
KBD Tape  
0~1mm  
0~1mm  
KBD Connector Cover Sheet  
Touch Panel model  
Lengthwise: Match to the top end of the KBD.  
Push the Cushion of the jig into the part with dotted frame ("A"),  
and press on the jig until the both ends of jig fit to the Top Case ("B").  
HINGE COVER  
Jig  
B
A
KBD CNT LID CUSHION  
B
Connector for the KBD FFC.  
Digitizer Model  
Screw  
Screw  
Screw  
Screw  
Screw  
KBD Connector Cover  
Connector for the KBD FFC.  
KBD Plate(L)  
Fix from the  
Hinge side.  
Screw  
Set it and then press it using the jig.  
(Insert the Hook first.)  
Safety Working  
Screw  
Before setting the KBD Plate (L)  
and the KBD Plate (R),  
press on the positions (four)  
with the two-sided tapes.  
30N(3.0Kgf)  
Connect the KBD FFC.  
KBD Plate(R)  
Fix from  
the Hinge side.  
! Putting of the Palm Rest ASSY  
5~7mm  
3~5mm  
3~5mm  
Windows Logo Label  
intel Label  
4~6mm  
Energy Star Label  
Remove the Release Paper, and then attach the Palmrest Assy.  
Remove the two-sided tape on the back side and attach it.  
Attach and apply the load 30 to 40N (3.0 to 4.0 Kgf).  
Palm rest Assy  
Set the four Hooks.  
LED Waterproof Sheet  
Match to the upper left corner. 0 to 0.3 mm  
Avoid running over when attaching.  
Don’t overflow.  
Release Paper  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-32  
7.2.18. Setting the Battery Pack and the HDD Pack  
1. Set the HDD in the HDD Case and fix it using the two  
3. Open the Battery Cover and set the Battery.  
Screws<A>.  
Screws<A>: DFHE5025XA  
HDD Case B  
Hooks  
HDD FPC  
HDD  
1
Hooks  
3
2
Heater  
<A>  
<A>  
HDD Case A  
2. Open the HDD Cover and set the HDD Pack.  
HDD Pack  
Battery Pack  
! Assembly of the HDD ASSY  
HDD Damper  
HDD Cushion Spacer  
HDD Case B(Assy)  
Set the FPC under the Damper.  
0~0.5mm  
Attach under the FPC  
(between the FPC  
and the HDD).  
Heater Insulation  
Sheet  
Avoid coming over the  
conductive part (metallic part)  
of the Heater.  
Remove the Release Papers  
(three) and attach them.  
Attach on the surface.  
HDD Case  
Tab  
0~1mm  
Attach on the inner  
side of the HDD  
Case A.  
HDD Case A  
0~1mm  
0~1mm  
Attach the HDD Case A,  
and then connect it.  
(Four joints)  
HDD GUIDE PIN  
Set the FFC to the pin of the HDD,  
and connect the Connector of the Heater  
to the FFC, and then attach them.  
Crosswise:  
-3 to +3 mm of  
the center of the  
HDD Guide  
Pin Plate  
HDD Guide  
Pin Plate  
0~0.5mm  
Sub material:  
HDD GUIDE PIN Assy  
inserted into pins  
PET TAPE 2  
(10 mm width x 3 cm)  
Lengthwise:  
Insulation Parts  
Cover the sensor  
of the FPC.  
Adheisive  
Tape  
Avoid coming over  
the HDD Guide  
Pin Plate.  
Shield Sheet  
(For GPS)  
0~0.5mm  
Safety Working  
Crosswise:  
-1 to +1 mm of  
Match to the  
center of the  
HDD Damper.  
0~5mm  
Fold it back once  
the center of  
and adjust the length.  
the HDD Guide Pin Plate  
0~0.5mm  
FPC ASSY  
Lengthwise:  
-0.5 to +0.5 mm  
ofthe center  
of the HDD Guide  
Pin Plate  
Completely cover the hole of the Case.  
Press and hold the leveled part, and attach it.  
HDD Guide  
Plate Spacer  
Insulation Parts  
Set the Hooks of the HDD Case A inside.  
FPC Assy  
0~0.5mm  
Ensure you can see it  
from the slit space of  
the HDD after assembly.  
Revision Label  
5–1mm  
FPC(HDD)  
HDD Spacer C  
5–1mm  
Insulation  
Parts  
Heater  
Press and  
hold it  
vertically,  
and screw it.  
0~0.5mm  
HDD  
Screw  
Use the jig.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-33  
7.2.19. Assembling the Each Cover  
1. Fix the Battery LID Ass'y, the HDD LID Ass'y, and the  
PCMCIA LID Ass'y using the six Screws<e>.  
<f>:No6  
<f>:No5  
<f>:No4  
<f>:No3  
<f>:No2  
<f>:No1  
2. Set the Rear Cabinet.  
3. Fix the Modem/LAN LID Rubber, the LAN LID Rubber, the  
USB LID Rubber, the DC IN LID Rubber, the Serial LID  
Rubber, the RGB LID Rubber,and the Audio LID Rubber  
using the 12 Screws<f>. No1 to No12  
DC IN LID Rubber  
USB LID Rubber  
LAN LID Rubber  
Moden/LAN LID Rubber  
Note:  
Tighten the Screws in the numbered order (No1 to No12).  
HDD LID ASS’Y  
Audio  
RGB  
LID Rubber  
LID Rubber  
<f>:  
Battery  
LID ASS’Y  
Screws <e>:DRQT26+D3FKL  
Screws <f>:DRHM5025YA  
<f>:  
No12  
<f>:No10  
No11  
<e>  
<e>  
<e>  
<e>  
<f>:No9  
<f>:No8  
<f>:No7  
Serial  
LID Rubber  
<e>  
PCMCIA LID ASS’Y  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7-34  
8 Exploded View  
K608  
A
K406  
K42  
K81  
K92  
K89  
A
K406  
E34  
A
K406  
K24  
K301  
K50  
K25  
K44  
K219  
K55  
K55  
K55  
K38  
E18  
A
K400  
A
K400  
K51  
A
K400  
K53  
K67  
K19  
K84  
K37  
K77  
F
K601  
K33  
K606  
K66  
F
K601  
K709  
K66  
K1  
K1-12  
K1-4  
K708  
K1-9  
K1-2  
K1-11  
K1-14  
K1-1  
K83  
K1-5  
K1-2  
K1-7  
E32  
K1-15  
Screw tightening torque  
A 0.2 _ 0.02N m  
+
K1-2  
(2.0 _ 0.2kgf cm)  
+
A
F 0.8 _ 0.02N m  
+
K1-6  
K1-10  
K1-8  
(8.0 _ 0.2kgf cm)  
+
K1-3  
CF-18NHHZXBM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B K83-4-2  
K83-4-1  
B
K83-4-5  
K83-4-6  
K83-5  
B
K83-4-2  
K83-4-1  
K83-4-4  
K71  
A
K83-4-3  
K83-3-8  
K83-3-9  
B
A
K83-5  
K83-3-3  
K83-3-4  
K83-4-9  
K83-4-7  
K83-4-3  
A
K83-3-9  
K83-4-8  
A K83-4-9  
K83-3-3  
K83-3-7  
K83  
K83-3-1  
B
K83-4  
K83-3  
K83-3-2  
B
K83-5  
K52  
K2  
E19  
K43  
E20  
K83-3-1  
K3  
K83-3-6  
B
K36  
K83-3-2  
B
K4  
K47  
K83-5  
K83-3-5  
E6  
K45  
K64  
E24  
K501  
B
K405  
K86  
K602  
K78  
K34  
K83-7  
K83-1  
A
A
K83-2-10  
A
K83-2  
K84  
K83-2-8  
C K83-6  
K83-2-9  
K83-2-3  
K83-2-4  
K503  
B
K686  
K40  
K405  
E
K410  
E
E5  
K83-2-9  
K410  
K49  
K83-2-3  
K83-2-7  
BT1  
K39  
K83-2-1  
B
K84  
B
K83-2-2  
Screw tightening torque  
A 0.2 _ 0.02N m  
+
K83-5  
(2.0 _ 0.2kgf cm)  
+
K83-2-1  
K83-2-6  
B K83-2-2  
B 0.3 _ 0.03N m  
+
(3.0 _ 0.3kgf cm)  
+
B
K83-5  
C 0.4 _ 0.05N m  
+
(4.0 _ 0.5kgf cm)  
+
K83-2-5  
E 1.50 _ 0.15N m  
+
(15.0 _ 1.5kgf cm)  
+
CF-18NHHZXBM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K402  
K83  
E3  
K406  
A
E26  
A
K406  
E42  
E1  
K5  
K57  
K696  
E27  
K76  
K687  
K604  
A
K406  
K84  
A
K408  
a
K607  
K620  
K685  
E2  
K408  
A
A
K408  
K718  
A
K406  
E36  
K32  
K15  
K18  
K550  
E150  
A
K414  
K84  
A
K407  
K31  
K59  
K17  
K26  
K60  
A
K406  
A
K41  
K406  
K671  
E35  
A
A
K551  
A
K406  
E11  
E151  
K16  
K414  
A
K414  
K85  
K58  
K400  
A
a
K697  
K698  
K698  
K688  
K690  
E210  
E4  
K35  
K84  
K35  
K695  
E208  
A
K400  
K689  
A
K400  
K689  
E25  
K620  
A
K400  
Screw tightening torque  
E22  
K699  
A 0.2 _ 0.02N m  
+
(2.0 _ 0.2kgf cm)  
+
CF-18NHHZXBM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K83  
K85  
K85  
K59  
K31  
A
K82-2  
K82  
A
A
K8  
K82-2  
K10  
K82-2  
K9  
K13  
K500  
K82-1  
A
K11  
K28  
K82-2  
K28  
A
K20  
K401  
K56  
K82-4  
K7  
K600  
A
K401  
A
K6  
K409  
K693  
K82-3  
K80  
A
K401  
K80-9  
K21  
K80-14  
K80-15  
K80-10  
K401  
A
K80-16  
K80-3  
K6  
K702  
A
K80-7  
K409  
A
K409  
K80-13  
K6  
K80-6  
K80-1  
K409  
A
A
A
K409  
K401  
A
K409  
K6  
K80-4  
A
K409  
K87  
K80-5  
K80-2  
A
K404  
D
Screw tightening torque  
A
K404  
A 0.2 _ 0.02N m  
+
K504  
K80-8  
A
K505  
(2.0 _ 0.2kgf cm)  
+
K80-8  
D
D 0.12 _ 0.01N m  
+
(1.2 _ 0.1kgf cm)  
K404  
+
CF-18NHHZXBM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K210  
K200-30  
K211  
K210  
K200-30-4  
K200-30-35  
K200-30-3  
K200-30-30  
K200-30-35-1  
K200-30-4  
E33  
B
K400  
K200-30-3  
B
K23  
K218  
K400  
K200-30-31  
D
K228  
K208  
K224  
K205  
K224  
K79  
E16  
D
K228  
K207  
K202  
K209  
E16-1  
K200-1-5  
K200-1-6  
K205  
B
K229  
K217  
K200-2  
K200-1-1  
K200-1-7  
K200-3  
K206  
K200-1-8  
K200-1-6  
K200-1-5  
K200  
-1-4  
K200  
-1-2  
E16-2  
K200-1-2  
K200-1-4  
K222  
K206  
K229  
E14-1  
K212  
E209-1  
E209  
B
K203  
K206  
K200-1-3  
B
K703  
K229  
E14  
E17  
K200-1  
B
K229  
Screw tightening torque  
K200  
K200-1-3  
B 0.2 _ 0.02N m  
+
(2.0 _ 0.2kgf cm)  
+
D 0.8 _ 0.08N m  
+
E17-1  
(8.0 _ 0.8kgf cm)  
+
CF-18NHHZXBM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K252  
E28  
K223  
K214  
K253  
K213  
E33  
K705  
E33-32  
E100  
A E33-5  
K704  
E29  
K222  
E33-31  
E33-32  
E33-6  
A
E33-5  
E33-35  
K222  
E33-1  
E33-30  
E33-34  
E33-1-2  
A
E33-5  
E33-34  
E33-1-1  
E33-33  
E33-35  
E33-30  
E33-7  
K220  
E33-8  
A
E33-5  
E33-9  
E33-8  
Screw tightening torque  
A 0.18 _ 0.02N m  
+
(1.8 _ 0.2kgf cm)  
+
CF-18NHHZXBM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C K225  
K215  
C
K225  
K216  
C
K225  
C K225  
K225  
C
C
K225  
K225  
C
B K226  
C K225  
K230  
K201  
B K226  
K201-1-4  
K201-1-2  
K201 -1-6  
K226  
B
K201-1-1  
K201-1  
K201-1-4  
K201-1-2  
K201-1-5  
K201-1-3  
D
K227  
B
K201-4  
K226  
K201-2  
D
K227  
K201-30  
K201-1-5  
K201  
-1-6  
B
K226  
K201-7  
K201-3  
K201-1  
-3  
K201-4  
K201-30  
K201-7  
C
K225  
K201-5  
K201-6  
K201-5  
C K225  
K201-6  
K215  
K201-5  
Screw tightening torque  
C
K225  
B 0.2 _ 0.02N m  
+
(2.0 _ 0.2kgf cm)  
+
C 0.3 _ 0.03N m  
+
(3.0 _ 0.3kgf cm)  
+
C K225  
D 0.8 _ 0.08N m  
+
(8.0 _ 0.8kgf cm)  
+
CF-18NHHZXBM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9 Replacement Parts List  
Note: Important Safety Notice  
Components identified by  
mark have special characteristics important for safety.  
When replacing any of these components, use only manufacturer's specified parts.  
CF-18NHHZXBM  
REF.NO. and AREA  
Main Block Unit  
E1  
PART NO.  
DL3U11471CAA  
DESCRIPTION  
Q'TY  
PCB, MAIN  
PCB, AUDIO  
PCB, I/O  
RTL  
RTL  
RTL  
RTL  
RTL  
RTL  
RTL  
RTL  
1
E2  
DL3U21471CAA  
DL3U31471CAA  
DL3U1B482AAA  
DL3U2B482AAA  
DL3U3B482AAA  
DL3U4B482AAA  
DL3U11490AAA  
DFJS834YA  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
2
2
1
3
1
2
1
2
2
1
1
1
1
1
1
1
E3  
E4  
PCB, PAD  
E5  
PCB, SWITCH  
PCB, LED  
E6  
E11  
PCB, PORT  
E14  
PCB, WIDE AREA ANTENNA  
GPRS CABLE, GRAY  
PCB, BT-LAN2 ANTENNA  
LAN MAIN CABLE, BLACK  
BT CABLE, BLUE  
PCB, LAN2 ANTENNA  
LAN SUB CABLE, WHITE  
TOUCH PAD  
E14-1  
E16  
DL3U31490AAA  
DFJS837YA  
RTL  
RTL  
E16-1  
E16-2  
E17  
DFJS835YA  
DL3U41490AAA  
DFJS836YA  
E17-1  
E18  
N2EABEC00006  
DFJS827YA  
E19  
CABLE, MODEM  
CABLE, LAN  
E20  
DFJS828YA  
E22  
DFJK08T024DB  
DFJK10T053DB  
DFJK12T034DB  
DFJK24T034DB  
DFJK40T072CB  
N0GB1J000018  
DFJS923YA  
FFC, SW  
E24  
FFC, LED  
E25  
FFC, PAD  
E26  
FFC, IO  
E27  
FFC, AUDIO  
E28  
INVERTER  
E29  
CABLE, LCD TS  
E32  
N3CABSD00008  
DFWV08A0076  
DL3DW0180AAA  
A2CA00000056  
DFHM0290ZA  
DXHM0042ZA  
DFHR3C08ZA  
DFHR3B64ZA  
DFHR3506YA  
DFHR3507YA  
DFHR3453YA  
DFHR3570YA  
DFHR3571YA  
DFHR3612ZA  
DFHR3647YA  
DFHR3648ZA  
N2ABAJ000001  
N5HAZ0000013  
N5HZC0000014  
K1YYZZ000058  
DL3U5B482AAA  
DL3UP1282AAA  
DFJS877YA  
HDD  
E33  
LCD UNIT ASS'Y  
LCD ASS'Y  
E33-1  
E33-1-1  
E33-1-2  
E33-5  
E33-6  
E33-7  
E33-8  
E33-9  
E33-30  
E33-31  
E33-32  
E33-33  
E33-34  
E33-35  
E34  
LCD BACKLIGHT, CCFL  
REFLECTION ANGLE  
SCREW  
LCD BACK DAMPER  
LCD SIDE CUSHION A  
LCD SIDE CUSHION C  
LCD SIDE CUSHION D  
LCD BACK CUSHION SIDE  
LCD BACK CUSHION  
LCD BACK CUSHION S  
LCD PWB SPACER  
SPACER SHEET  
HOLDER SHEET B  
KEYBOARD, US  
MDC MODEM  
E35  
E36  
WIRELESS LAN MODULE  
CARD BUS SOCKET  
PCB, TS PS2  
E42  
E100  
E150  
E151  
RTL  
RTL  
PCB, ANTENNA  
CABLE, ANTENNA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E208  
DFJK13T024DB  
DL3U21490AAA  
DFJS977ZA  
FFC, PAD  
1
1
1
1
E209  
PCB, WIDE AREA AUX ANTENNA  
CABLE, WIDE AREA AUX ANT. BROWN  
PCB, SD  
RTL  
RTL  
E209-1  
E210  
DL3U7B482AAA  
Accessories  
A1  
CF-AA1623AM6  
K2CG3DR00003  
DFQX5561YA  
CGR-B/6D8A  
DFJS954ZA  
AC ADAPTOR  
AC CABLE  
1
1
1
1
1
1
1
1
A2  
A3  
MANUAL  
A4  
BATTERY PACK  
MODEM CABLE  
CLOTH ASS'Y  
SHOULDER BELT ASS'Y  
TETHER  
A6  
A7  
DFHS9017ZA  
DFQC9006ZB-0  
DFME0134ZA  
A25  
A26  
Packing Material  
P1  
DFPK1147QA  
DFPE0599ZA  
DFPE0733YA  
CASE, PACKING  
HOLDER  
1
1
1
P2  
P3  
ACCESSORIES BOX  
Mechanical Parts  
K1  
DFWV99A0104  
L9DZAA000004  
DFMX0383TA  
DFHM0280YA  
DFHM0313ZA  
DFHM9007ZA  
DFHE5025XA  
DFHR3443XA  
DFHR3589ZA  
DFHR3601ZA  
DFHR3627YA  
DL3UP1279BAA  
DFHP7124ZA  
DFHR3A10ZA  
DFMX1207ZA  
DFHE0326XA  
DFHE0519XA  
DFHE0811YA  
DFHE0815ZA  
DFHG1209ZA  
DFHG1630ZA-0  
DFHG1632XA-0  
DFHG1638ZA-0  
DFHG1639ZA-0  
DFHG1641ZB-0  
DFHG1660ZA-0  
DFHG427YA  
HDD MOUNTING KIT  
HEATER  
1
1
3
1
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
4
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
K1-1  
K1-2  
K1-3  
K1-4  
K1-5  
K1-6  
K1-7  
K1-8  
K1-9  
K1-10  
K1-11  
K1-12  
K1-14  
K1-15  
K2  
INSULATION SHEET  
HDD CASE A  
MDD GUIDE PIN PLATE  
HDD CASE B  
SCREW  
HDD DAMPER  
HDD CASE TAB  
HDD GUIDE PLATE SPACER  
HDD CUSHION SPACER  
FPC ASS'Y, HDD  
TAPE  
HDD SPACER C  
INSULATION SHEET, HDD HEATER  
GASKET  
K3  
GASKET E  
K4  
GASKET  
K5  
CONDUCTIVE SHEET  
RUBBER, FOOT  
K6  
K7  
AUDIO LID RUBBER  
DC IN LID RUBBER  
MODEM/LAN LID RUBBER  
USB LID RUBBER  
RGB LID RUBBER  
LAN LID RUBBER  
ANTENNA CAP  
K8  
K9  
K10  
K11  
K13  
K15  
K16  
K17  
K18  
K19  
K20  
K21  
K23  
K24  
K25  
K26  
K28  
DFHM0379ZA  
DFHM0276SA  
DFHM0282YA  
DFHM0284XA  
DFHM0286YB  
DFHM0288ZB  
DFHM0296XA-0  
DFHM0302YA-0  
DFHM0303YA-0  
DFHM0307YA  
DFHM0311ZB  
CPU HEAT PLATE  
DU CNT ANGLE  
HDD GUIDE PLATE ASM  
KB CNT LID  
LID RUBBER PLATE A  
LID RUBBER PLATE C  
LCD HINGE COVER  
KBD PLATE (L)  
KBD PLATE (R)  
BAT CON ANGLE  
LID RUBBER PLATE B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K31  
DFHR3262ZA  
DFHR3301YA  
DFHR3438ZA  
DFHR3808ZA  
DFHR3445YA  
DFHR3450ZA  
DFHR3451ZB  
DFHR3474YA  
DFHR3483SA  
DFHR3485ZA  
DFHR3487ZA  
DFHR3510ZA  
DFHR3B11YA  
DFHR3512ZA  
DFHR3513ZA  
DFHR3536YA  
DFHR3551YA  
DFHR3581YA  
DFHR3582ZA  
DFHR3583ZA  
DFHR3584ZA  
DFHP7106YA  
DFHR3622ZA-0  
DFHR3623ZA  
DFHR3624ZA  
DFHR3625ZA  
DFHR3626ZA  
DFHR3636ZA  
DFHR3642YA  
DFHR3643ZA  
DFHR3655YA  
DFHR3677ZA  
DFHR6044XA  
DFHR6052XB-0  
DFHR9081ZA  
DFKE9078YA-0  
L0AA04A00022  
DFHM0275ZB  
DFHM0298YA  
DFHR3439ZA  
DFHR3471ZA  
DFHR3520ZA  
DFHR3535ZA  
DRHM5025YA  
DFMX1070ZA  
DFHM0377YA  
DFMX1197ZA  
DFHR3C04ZA  
DFHR3C05ZA  
DFHR8509ZA  
DFKE9065WA-0  
DFKM9030ZA-0  
DFHM0277YA  
DRHM5025YA  
DFHR3441ZA  
DFHR6045ZA  
MODEM TAPE  
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
2
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
5
1
1
K32  
MINI PCI CARD SHEET  
CLICK BUTTON SHEET  
GPS HOLE SHEET  
HEAT DISSIPATION RUBBER  
KB CNT HOLE CUSHION  
KB CNT LID SHEET  
TP TAPE  
K33  
K34  
K35  
K36  
K37  
K38  
K39  
OPERATION SHEET  
OPERATION TAPE  
PORTRE SHEET  
K40  
K41  
K42  
LED SHEET  
K43  
SHEET, PCMCIA  
K44  
LED WATERPROOF SHEET  
LED PWB TAPE  
K45  
K47  
LED LIGHT GUIDE SHEET  
COIN BATTERY SHEET  
KBD WATERPROOF SHEET L  
KBD WATERPROOF SHEET R  
KBD WATERPROOF SHEET C  
PALMREST SHEET R  
TAPE  
K49  
K50  
K51  
K52  
K53  
K55  
K56  
DU STOPPER  
K57  
DU STOPPER A  
K58  
DU STOPPER B  
K59  
DU STOPPER C  
K60  
DU STOPPER D  
K64  
CABLE HOLD SHEET  
LCD CUSHION SHEET  
TP BOTTOM TAPE  
HDD CASE SPACER  
INSULATION SHEET  
CLICK BUTTON PLATE  
POWER SW KNOB  
PEN  
K66  
K67  
K71  
K76  
K77  
K78  
K79  
K80  
DIMM LID ASSY SD  
SPEAKER UNIT  
K80-1  
K80-2  
K80-3  
K80-4  
K80-5  
K80-6  
K80-7  
K80-8  
K80-9  
K80-10  
K80-13  
K80-14  
K80-15  
K80-16  
K81  
DIMM LID  
SPEAKER ANGLE  
DIMM LID SHEET  
SP WATERPROOF SHEET  
SPEAKER WASHER  
SPEAKER CABLE TUBE  
SCREW  
FDD INSULATION SHEET (2)  
DIMM HEAT SINK PLATE  
SPEAKER INSULATION SHEET  
DIMM CARD INSULATION SHEET  
DIMM TIP INSULATION SHEET  
DIMM PLATE SPACER  
PALM REST ASS'Y  
BOTTOM CASE ASS'Y  
DU LID ANGLE  
K82  
K82-1  
K82-2  
K82-3  
K82-4  
SCREW  
DU LID WATERPROOF SHEET  
DU LID  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K83  
DFKM9034XA-0  
DFKE9073YA-0  
DFKE9071ZA-0  
DFBH3030ZA  
DRQT26+D3FKL  
DFHM0310YA  
DFHM0315YC  
DFHR3509YA  
DFKE0799ZA-0  
DFUN0068XA  
DFUS0292ZB  
DRHM5025YA  
DXQT2+F3FNLT  
DFKE9072ZB-0  
DFBH3030ZA  
DRQT26+D3FKL  
DFHM0310YA  
DFHM0285XC  
DFHR3508YA-0  
DFKE0799ZA-0  
DFUN0068XA  
DFUS0292ZB  
DRHM5025YA  
DFKE9075XA-0  
DFBH3030ZA  
DRQT26+D3FKL  
DFHM0310YA  
DFHM0285XC  
DFHR3588WA-0  
DFKE0799ZA-0  
DFUN0068XA  
DFUS0292ZB  
DRHM5025YA  
DRQT26+D3FKL  
DXQT3+F4FNLT  
DFHR3480ZA  
DFMX0383TA  
DFHR7518ZA  
DFUQ0101YA  
DFGT1054ZA  
DFQT9675ZA  
DFQT9948ZA  
DFWV80A0354  
DFKF9031ZA-0  
DRHM5025YA  
DFHG1634YA-0  
DFHG1635ZA-0  
DFHM0319YA  
DFHM0321ZA  
DFHM0322ZA  
DFHR3469ZA  
DFHR6051ZE  
DFHE0805ZA  
DFHP7149ZA  
DFWV84A0261  
DFHR3476ZA  
TOP CASE ASS'Y  
TABLET LATCH ASS'Y  
BATT LID ASS'Y  
LID HINGE  
1
1
1
2
2
2
1
1
1
1
1
2
1
1
2
2
2
1
1
1
1
1
3
1
2
2
2
1
1
1
1
1
3
6
2
1
10  
3
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
2
K83-1  
K83-2  
K83-2-1  
K83-2-2  
K83-2-3  
K83-2-4  
K83-2-5  
K83-2-6  
K83-2-7  
K83-2-8  
K83-2-9  
K83-2-10  
K83-3  
SCREW  
WASHER  
LID LATCH PLATE BATT  
BAT COVER SHEET  
TABLE LATCH KNOB  
LID KNOB SPRING  
LID KNOB SPRING PLATE  
SCREW  
SCREW  
HDD LID ASS'Y  
K83-3-1  
K83-3-2  
K83-3-3  
K83-3-4  
K83-3-5  
K83-3-6  
K83-3-7  
K83-3-8  
K83-3-9  
K83-4  
LID HINGE  
SCREW  
WASHER  
LID LATCH PLATE  
HDD COVER SHEET  
TABLE LATCH KNOB  
LID KNOB SPRING  
LID KNOB SPRING PLATE  
SCREW  
PCMCIA LID ASS'Y  
LID HINGE  
K83-4-1  
K83-4-2  
K83-4-3  
K83-4-4  
K83-4-5  
K83-4-6  
K83-4-7  
K83-4-8  
K83-4-9  
K83-5  
SCREW  
WASHER  
LID LATCH PLATE  
PCMCIA COVER SHEET SD  
TABLE LATCH KNOB  
LID KNOB SPRING  
LID KNOB SPRING PLATE  
SCREW  
SCREW  
K83-6  
SCREW  
K83-7  
WL DUMMY SHEET  
INSULATION SHEET  
H CABLE SHEET  
SW SPRING  
K84  
K85  
K86  
K87  
RATED LABEL  
K89  
ENERGY STAR LABEL  
CENTRINO LABEL  
LCD FRONT CABINET/TS PANEL ASS'Y  
FRONT CASE ASS'Y  
SCREW  
K92  
K200  
K200-1  
K200-1-1  
K200-1-2  
K200-1-3  
K200-1-4  
K200-1-5  
K200-1-6  
K200-1-7  
K200-1-8  
K200-2  
K200-3  
K200-30  
K200-30-3  
LCD CABINET CUSHION A  
LCD CABINET CUSHION B  
LCD ELE PASS  
D WASHER  
SPRING WASHER  
PEN FRICTION SHEET  
PEN HOLDER  
MAGNET  
MAGNET TAPE  
TOUCH SCREEN PANEL KIT  
SPACER A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K200-30-4  
K200-30-30  
K200-30-31  
K200-30-35  
K200-30-35-1  
K201  
DFHR3477ZA  
DFHR3630ZA  
DFHR3674YA  
DL3DV0180AAA  
DFHR9071ZA  
DFWV80C0497  
DFKM9032ZA-0  
DFHR3468ZA-0  
DFHG1634YA-0  
DFHG1635ZA-0  
DFHM0319YA  
DFHM0321ZA  
DFHM0322ZA  
DFHR3563YA  
DFHR3564YA  
DFHR3565YA  
DFHR3566YA  
DFHR3460YA  
DFHR3461YA  
DFHR3567YA  
DFBH3029VA  
DFHE0814ZA  
DFHM0325ZA  
DFHR3432ZA  
DFHR3464WA  
DFHR3516ZA  
DFHR3572YA  
DFHR3573YA  
DFHR3574YA  
DFHR3614ZA  
DFHR3631YA  
DFHR3A65ZA  
DFHR6193YA-1  
DFHR6106ZC-1  
DFHR6081ZA-0  
DFKE9059YA  
DFKE9074ZA-0  
DFMC0685ZA  
DFMX0383TA  
DFQT6077YA  
DFUQ0100ZA  
DRQT26+E5FKL  
DXYN2+J6FNL  
DXYN3+J10FNL  
DXYN3+J8FNL  
DFHE5025XA  
DFHR3472ZA-0  
DFMC0808ZA  
DFMC0816ZA  
DFQT9869ZA-0  
DFHE5025XA  
DRHM5025YA  
DFHE5058ZB  
DRQT2+D2FKL  
DXQT3+D4FKNL  
DRSB2+5FKL  
SPACER B  
2
1
TS FPC SPACER  
TS TAPE  
1
TS PANEL ASS'Y  
PROTECTION FILM  
LCD REAR CABINET ASS'Y  
REAR CASE ASS'Y  
PANA BADGE  
1
1
1
K201-1  
K201-1-1  
K201-1-2  
K201-1-3  
K201-1-4  
K201-1-5  
K201-1-6  
K201-2  
K201-3  
K201-4  
K201-5  
K201-6  
K201-7  
K201-30  
K202  
1
1
LCD CABINET CUSHION A  
LCD CABINET CUSHION B  
LCD ELE PASS  
2
2
2
D WASHER  
2
SPRING WASHER  
LCD REAR CUSHION C  
LCD REAR CUSHION D  
LCD REAR CUSHION E  
LCD REAR CUSHION F  
LCD REAR CUSHION A  
LCD REAR CUSHION B  
LCD REAR CUSHION G  
LCD HINGE  
2
2
1
2
3
2
2
2
1
K203  
CONDUCTIVE SHEET  
CABLE HOLD PLATE  
ANT CABLE CUSHION  
LCD SIDE CUSHION B TP  
PROTECT SHEET, SCREW  
LCD CABLE HOLDER SHEET  
LCD SIDE CUSHION E  
LCD SIDE CUSHION F  
CABLE STOPPER TAPE  
INVERTER CASE  
INSULATION SHEET INV. CASE  
ANTENNA COVER  
TABLET LATCH COVER  
CABLE HOLDER  
1
K205  
2
K206  
3
K207  
2
K208  
1
K209  
1
K210  
2
K211  
1
K212  
1
K213  
1
K214  
1
K215  
2
K216  
1
K217  
2
K218  
LOCK PLATE ASSY  
HINGE TOP COVER ASSY  
CONDUCTIVE SHEET, LCD  
INSULATION SHEET  
CAUTION LABEL, LCD  
LOCK SPRING  
1
K219  
1
K220  
1
K222  
4
K223  
1
K224  
2
K225  
SCREW  
16  
10  
2
K226  
SCREW  
K227  
SCREW  
K228  
SCREW  
2
K229  
SCREW  
8
K230  
TOUGH BADGE  
1
K252  
INVERTER MIL COVER  
INVERTER MIL SHEET  
RELEASE LABEL  
SCREW  
1
K253  
1
K301  
1
K400  
13  
13  
4
K401  
SCREW  
K402  
SCREW, DSUB  
K404  
SCREW  
4
K405  
SCREW  
2
K406  
SCREW  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
K407  
K408  
K409  
K410  
K414  
K500  
K501  
K503  
K504  
K505  
K550  
K551  
K600  
K601  
K602  
K604  
K606  
K607  
K608  
K620  
K671  
K685  
K686  
K687  
K688  
K689  
K690  
K693  
K695  
K696  
K697  
K698  
K699  
K702  
K703  
K704  
K705  
K708  
K709  
K718  
DXYN2+J12FNL  
DXYN2+J18FNL  
DRHM0061ZA  
DXYN4+J8FNL  
XSB2+4FNL  
SCREW  
2
3
13  
4
4
1
1
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
3
1
1
1
2
1
2
1
2
1
1
1
1
1
1
SCREW  
SCREW  
SCREW  
SCREW  
DFHG1633ZB-0  
DFHR3539YA  
DFHR3644ZA  
DFQT6255ZA  
DFQT6311ZA  
DFHR3488ZA  
DFHE5108ZA  
DFMY0419ZA  
DRYN3+J6FKL  
DFHR3809ZB  
DFHR3969ZA  
DFQC9009ZC-0  
DFHR8516ZA  
DFQT9974ZA  
DFHR3741ZA  
DFHG1790ZA  
DFMC0848YA  
DFMX1200ZA  
DFMY0248YA  
DFHM0378ZA  
DXQN2+A22FNL  
DXSN2+18FNL  
DFHR3859ZA  
DFHR3B12ZA  
DFHR3B65ZA  
DFHR3B84YA  
DFHR3B85ZA  
DFHR3B87ZA  
DFHR8517ZA  
DFHE0915ZA  
DFHR3C06ZA  
DFHR3C07ZA  
DFMD3125ZA  
DFHP7200ZA  
DFHR6220ZA  
RUBBER, SERIAL LID  
SHEET, HEAD SET DUMMY  
TAPE, SIMM DUMMY  
LABEL, W-LAN  
LABEL, FCC ID  
SHEET, EXT ANTENNA  
SCREW  
DIMM THERMAL RUBBER  
SCREW  
GPS HOLE SHEET B  
PCMCIA SHEET 3  
STRAP BG ASS'Y  
FFC SPACER  
WINDOS XP LABEL (FOR NOTE)  
FFC CN STOPPER  
BAT CUSHION  
GASKET  
INS. SHEET, TOUCH PAD CARD  
CPU HEATSINK RUBBER  
SD ANGLE  
SCREW  
SCREW  
DC IN SHEET  
SHEET, SD BOARD  
CUSHION, HDD PACK  
SPACER, SD ANGLE (1)  
SPACER, SD ANGLE (2)  
SHEET, SD FFC  
CUSHION, HDD  
SHEET  
INVERTER SHEET (1)  
INVERTER SHEET (2)  
BACK PLATE, KENSINGTON 2  
TAPE, AHDESIVE  
DIMM HOLDER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts List  
Note: Important Safety Notice  
Components identified by  
mark have special characteristics important for safety.  
When replacing any of these components use only manufacturer's specified parts.  
CF-18NHHZXBM  
REF. NO and AREA  
MAIN PCB  
BT 1  
C 2  
PART NO.  
DESCRIPTION  
Q'TY  
CR2032/S5W  
F1J0J106A016  
RTC BATTERY  
CAPACITOR, 6.3V, 10µF  
1
76  
C 3  
C 4  
C 6  
C 7  
C 8  
C 11  
C 12  
C 13  
C 15  
C 16  
C 17  
C 19  
C 20  
C 21  
C 23  
C 24  
C 25  
C 26  
C 29  
C 30  
C 31  
C 32  
C 34  
C 35  
C 36  
C 37  
C 40  
C 41  
C 42  
C 43  
C 45  
C 46  
C 47  
C 48  
C 49  
C 54  
C 62  
C 63  
C 64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 70  
C 77  
C 85  
C 86  
C 96  
C 98  
C 99  
C 102  
C 103  
C 107  
C 165  
C 170  
C 176  
C 177  
C 180  
C 252  
C 253  
C 278  
C 287  
C 290  
C 303  
C 304  
C 314  
C 316  
C 328  
C 329  
C 335  
C 341  
C 343  
C 348  
C 352  
C 353  
C 369  
C 392  
C 396  
C 692  
C 5  
EEFCD0D151ER  
F1G1C104A042  
CAPACITOR, 2V, 150µF  
CAPACITOR, 16V, 0.1µF  
4
C 208  
C 214  
C 688  
C 9  
159  
C 10  
C 14  
C 18  
C 22  
C 27  
C 33  
C 38  
C 39  
C 44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 60  
C 61  
C 65  
C 67  
C 68  
C 69  
C 74  
C 75  
C 76  
C 78  
C 79  
C 82  
C 88  
C 97  
C 100  
C 106  
C 109  
C 111  
C 112  
C 115  
C 116  
C 117  
C 118  
C 121  
C 122  
C 123  
C 124  
C 127  
C 128  
C 130  
C 131  
C 134  
C 135  
C 140  
C 148  
C 149  
C 150  
C 151  
C 156  
C 157  
C 158  
C 159  
C 160  
C 161  
C 162  
C 163  
C 167  
C 191  
C 192  
C 193  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 196  
C 198  
C 199  
C 202  
C 203  
C 206  
C 207  
C 209  
C 210  
C 211  
C 213  
C 216  
C 217  
C 218  
C 219  
C 224  
C 225  
C 226  
C 227  
C 228  
C 229  
C 230  
C 231  
C 232  
C 233  
C 235  
C 237  
C 238  
C 242  
C 243  
C 247  
C 254  
C 255  
C 256  
C 261  
C 262  
C 263  
C 264  
C 266  
C 267  
C 268  
C 274  
C 276  
C 280  
C 282  
C 284  
C 285  
C 286  
C 288  
C 289  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 291  
C 292  
C 293  
C 311  
C 312  
C 313  
C 315  
C 318  
C 321  
C 322  
C 326  
C 336  
C 345  
C 346  
C 349  
C 350  
C 351  
C 354  
C 361  
C 362  
C 363  
C 364  
C 365  
C 366  
C 367  
C 368  
C 377  
C 382  
C 383  
C 384  
C 388  
C 389  
C 391  
C 393  
C 394  
C 395  
C 399  
C 400  
C 430  
C 432  
C 433  
C 434  
C 435  
C 436  
C 601  
C 607  
C 629  
C 635  
C 636  
C 50  
F1G1E103A062  
CAPACITOR, 25V, 0.01µF  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 166  
C 168  
C 169  
C 171  
C 174  
C 175  
C 178  
C 179  
C 197  
C 215  
C 234  
C 245  
C 246  
C 265  
C 269  
C 270  
C 271  
C 296  
C 299  
C 307  
C 309  
C 347  
C 375  
C 600  
C 628  
C 630  
C 689  
C 55  
F1G1H222A496  
F1G1A104A014  
CAPACITOR, 50V, 2200pF  
CAPACITOR, 10V, 0.1µF  
1
7
C 56  
C 57  
C 187  
C 330  
C 331  
C 332  
C 333  
C 66  
F1H0J1050022  
CAPACITOR, 6.3V, 1µF  
13  
C 84  
C 108  
C 141  
C 164  
C 181  
C 249  
C 251  
C 272  
C 317  
C 319  
C 360  
C 390  
C 71  
F1G1H102A496  
CAPACITOR, 50V, 1000pF  
20  
C 275  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 277  
C 281  
C 283  
C 339  
C 344  
C 378  
C 379  
C 380  
C 419  
C 420  
C 616  
C 623  
C 637  
C 638  
C 659  
C 666  
C 677  
C 684  
C 72  
EEFCX0D331R  
CAPACITOR, 2V, 330µF  
8
C 73  
C 80  
C 81  
C 83  
C 650  
C 651  
C 652  
C 87  
F1G1A474A018  
CAPACITOR, 10V, 0.47µF  
7
C 89  
C 90  
C 91  
C 93  
C 94  
C 95  
C 92  
F1G0J224A001  
CAPACITOR, 6.3V, 0.22µF  
CAPACITOR, 2V, 100µF  
2
4
C 105  
C 101  
C 653  
C 671  
C 693  
C 104  
C 110  
C 113  
C 114  
C 119  
C 120  
C 125  
C 126  
C 129  
C 132  
C 133  
EEFCD0D101ER  
EEFCX0D221R  
F1H1A1050015  
CAPACITOR, 2V, 220µF  
CAPACITOR, 10V, 1µF  
1
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 152  
C 153  
C 154  
C 155  
C 188  
C 194  
C 195  
C 244  
C 603  
C 640  
C 698  
C 799  
C 136  
C 137  
C 142  
C 143  
C 398  
C 172  
C 173  
C 183  
C 279  
C 387  
C 612  
C 641  
C 642  
C 643  
C 657  
C 668  
C 686  
C 186  
C 189  
C 257  
C 258  
C 294  
C 295  
C 297  
C 298  
C 618  
C 619  
C 625  
C 661  
C 662  
C 674  
C 679  
C 680  
C 323  
C 325  
C 327  
C 337  
C 606  
F1G1H3R3A543  
F1G1H150A542  
CAPACITOR, 50V, 3.3pF  
CAPACITOR, 50V, 15pF  
2
3
F1G1H270A451  
F1G1H1010005  
CAPACITOR, 50V, 27pF  
CAPACITOR, 50V, 100pF  
2
10  
F1G1H5R0A452  
EEFUD0J151ER  
F1G1H221A495  
CAPACITOR, 50V, 5pF  
CAPACITOR, 6.3V, 150µF  
CAPACITOR, 50V, 220pF  
2
2
12  
F1G1H6R0A452  
CAPACITOR, 50V, 6pF  
2
F1L3D102A003  
F1H1H104A748  
CAPACITOR, 2000V, 1000pF  
CAPACITOR, 50V, 0.1µF  
1
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 613  
C 615  
C 622  
C 655  
C 658  
C 665  
C 673  
C 675  
C 676  
C 683  
C 694  
C 695  
C 697  
C 699  
C 700  
C 355  
C 356  
C 358  
C 359  
C 604  
C 374  
C 632  
C 633  
C 634  
C 376  
C 411  
C 412  
C 608  
C 609  
C 611  
C 626  
C 648  
C 649  
C 654  
C 669  
C 672  
C 687  
C 701  
C 614  
C 624  
C 617  
C 620  
C 660  
C 663  
C 678  
C 681  
C 621  
C 646  
C 664  
C 682  
F1J1E105A009  
F1G1C473A004  
CAPACITOR, 25V, 1µF  
5
4
CAPACITOR, 16V, 0.047µF  
F1G1A683A014  
F1G1H100A544  
CAPACITOR, 10V, 0.068µF  
CAPACITOR, 50V, 10pF  
1
2
EEFCX0J101R  
F1L1E106A017  
CAPACITOR, 6.3V, 100µF  
CAPACITOR, 25V, 10µF  
2
9
F1H1H103A748  
F1G1H220A542  
CAPACITOR, 50V, 0.01µF  
CAPACITOR, 50V, 22pF  
2
6
F1J0J475A009  
CAPACITOR, 6.3V, 4.7µF  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 627  
C 639  
C 644  
C 645  
C 656  
C 667  
C 670  
C 685  
C 696  
C 702  
C 703  
C 704  
EEFCX0G151R  
F1G1H471A496  
F1G1H681A496  
F1J1E334A081  
F1H1H182A748  
CAPACITOR, 4V, 150µF  
CAPACITOR, 50V, 470pF  
CAPACITOR, 50V, 680pF  
CAPACITOR, 25V, 0.33µF  
CAPACITOR, 50V, 1800pF  
1
1
1
1
2
EEFCD0G101ER  
F1H1E472A050  
F1G1H152A496  
F1K1E1060001  
CAPACITOR, 4V, 100µF  
CAPACITOR, 25V, 4700pF  
CAPACITOR, 50V, 1500pF  
CAPACITOR, 25V, 10µF  
1
1
1
2
EEFCD0J470ER  
D4CC1103A038  
CAPACITOR, 6.3V, 47µF  
THERMISTOR  
1
2
CF 1  
CF 6  
CN 6  
CN 7  
CN 2  
CN 3  
CN 4  
CN 5  
CN 8  
CN 9  
CN 11  
CN 12  
CN 14  
CN 15  
CN 16  
CN 17  
CN 18  
CN 20  
CN 21  
CN 23  
CN 24  
CN 25  
CN 27  
CN 30  
CN 37  
CN 35  
D 1  
K1FB104B0055  
CONNECTOR  
2
K1MML0B00004  
K1KA02BA0014  
K1NAF0D00003  
K1KB50BA0001  
K1KA20AA0261  
K1MN24BA0059  
K1MMC4B00013  
K1KA08AA0266  
K1KA02B00247  
K1KA10B00213  
K1MN50AA0018  
K1KA11AA0267  
K1MN26AA0074  
K1MY04AA0041  
K1MN12AA0018  
K1MN13AA0018  
K1KB30A00171  
K1KAA0A00143  
K1MY40BA0098  
K1MN06AA0058  
K1KA02AA0229  
K1MN10AA0018  
MA2J72900L  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
DIODE  
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
D 2  
D 3  
D 11  
D 4  
B0JDBE000002  
MA3J14700L  
DIODE  
DIODE  
DIODE  
3
3
3
D 6  
D 625  
D 7  
D 8  
D 9  
D 10  
B0JCPD000023  
D 600  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D 799  
D 12  
B0KB00000044  
B0ADDH000004  
DIODE  
DIODE  
2
3
D 13  
D 601  
D 602  
D 603  
D 604  
D 605  
D 606  
D 622  
D 608  
D 609  
D 611  
D 626  
D 628  
D 629  
D 631  
D 632  
D 610  
D 627  
D 630  
D 612  
D 613  
D 614  
D 615  
D 617  
D 618  
D 616  
D 619  
D 621  
D 620  
D 623  
D 624  
F 1  
MAZ81200ML  
MAZ81800ML  
MA3S132E0L  
DIODE  
DIODE  
DIODE  
1
1
2
B0JCQD000001  
B0JCMD000014  
DIODE  
DIODE  
1
7
B0JDAE000004  
MAZ80510ML  
DIODE  
DIODE  
3
6
MAZ80620ML  
MA2S111-TX  
DIODE  
DIODE  
1
2
B2ABAM000002  
B0JCCE000008  
DEDRB081L20  
K5H502Z00003  
K5H202Z00005  
DIODE  
1
1
1
1
4
DIODE  
DIODE  
FUSE, 5A  
FUSE, 2A  
F 2  
F 3  
F 4  
F 6  
IC 1  
C2GBC0000263  
C1DB00001476  
C1DB00001359  
C0JBZZ000327  
C0JBAZ002423  
C0DBZHG00043  
IC, CPU  
1
1
1
1
1
2
IC 2  
IC, CHIP SET  
IC 3  
IC, CHIP SET  
IC 4  
IC, THERMAL SENSOR  
IC, CLOCK GENERATOR  
IC, USB POWER CONTROL  
IC 9  
IC 10  
IC 13  
IC 11  
IC 12  
IC 14  
IC 15  
IC 16  
C1DB00001182  
C3EBCG000100  
C1DB00001159  
C0EBE0000460  
IC, LAN CONTROLLER  
IC, EEPROM  
1
1
1
3
IC, PERIPHERAL LSI  
IC  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IC 17  
IC 18  
IC 19  
IC 20  
IC 33  
IC 39  
IC 44  
IC 650  
IC 21  
IC 23  
IC 24  
IC 28  
IC 29  
IC 26  
IC 27  
IC 30  
IC 31  
IC 32  
IC 37  
IC 34  
IC 36  
IC 35  
IC 41  
IC 38  
IC 42  
IC 43  
IC 46  
IC 60  
IC 61  
IC 62  
IC 63  
IC 64  
IC 65  
IC 66  
IC 67  
IC 600  
IC 601  
IC 602  
IC 603  
IC 604  
IC 605  
IC 607  
IC 608  
IC 610  
IC 611  
IC 612  
L 1  
C2CBJA000003  
C0CBCBC00137  
C0JBAA000347  
IC, MICON  
1
1
5
IC, REGURATOR  
IC, 1 GATE LOGIC  
C0JBAS000215  
DA2205IDBLET  
C0JBAS000218  
IC, GATE LOGIC  
IC, BIPOLAR LOGIC  
IC, LOGIC  
1
1
3
C0ZBZ0000978  
C0JBAB000619  
C3FBLC000040  
C1CB00002268  
C0JBAC000338  
IC  
1
1
1
1
2
IC, GATE LOGIC  
IC, FLASH MEMORY  
IC, SECURITY CHIP  
IC, GATE LOGIC  
C0JBAA000348  
C0JBAE000306  
IC, 1 GATE LOGIC  
IC,  
2
2
C0JBAC000339  
C1DB00001179  
C0EBH0000457  
C0JBAA000362  
C3ABSG000029  
IC,  
1
1
1
1
8
IC, LSI  
IC  
IC, LOGIC  
IC, DDR2 SDRAM  
C0ABZA000047  
C0ABBA000093  
C0DBAFH00029  
C0JBAD000182  
C0JBAB000622  
C0DBEFH00002  
C0EBE0000333  
C0DBDJH00009  
C0DBALH00003  
IC, AMP  
1
1
1
1
1
1
1
1
3
IC, OP AMP  
IC  
IC, LOGIC  
IC, 1 GATE LOGIC  
IC, REGURATOR  
IC  
IC, LINEAR  
IC  
G1C100Z00013  
G1C1R0Z00002  
INDUCTOR  
INDUCTOR  
2
5
L 2  
L 3  
L 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
L 5  
L 7  
L 8  
L 6  
G1C91NM00001  
J0JJC0000015  
J0MAB0000116  
INDUCTOR  
INDUCTOR  
INDUCTOR  
1
1
4
L 9  
L 10  
L 11  
L 25  
L 26  
L 12  
L 13  
L 14  
L 15  
L 16  
L 17  
L 18  
L 21  
L 22  
L 27  
L 28  
L 600  
L 601  
L 602  
L 603  
L 605  
L 604  
L 606  
L 607  
J0JHC0000074  
INDUCTOR  
4
J0MAB0000169  
J0JDC0000045  
INDUCTOR  
INDUCTOR  
2
5
DDAZS100MT3T  
G1C100MA0106  
G1C1R6Z00001  
G1C4R7MA0106  
INDUCTOR  
INDUCTOR  
INDUCTOR  
INDUCTOR  
1
1
1
2
G1C220MA0077  
G1C4R7MA0022  
G1A160H00001  
K5J1AB000001  
UNR9214J0L  
INDUCTOR  
INDUCTOR  
INDUCTOR  
POLY SW  
1
1
1
PA 1  
1
Q 1  
TRANSISTOR  
12  
Q 4  
Q 5  
Q 11  
Q 15  
Q 35  
Q 611  
Q 627  
Q 636  
Q 641  
Q 642  
Q 643  
Q 2  
B1DHDC000028  
TRANSISTOR  
11  
Q 3  
Q 8  
Q 14  
Q 16  
Q 19  
Q 22  
Q 24  
Q 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Q 31  
Q 625  
Q 6  
B1MBBCA00003  
TRANSISTOR  
4
Q 7  
Q 9  
Q 10  
Q 12  
B1CFFB000001  
XP0421300L  
TRANSISTOR  
TRANSISTOR  
2
Q 13  
Q 17  
10  
Q 21  
Q 25  
Q 612  
Q 617  
Q 618  
Q 619  
Q 621  
Q 623  
Q 626  
Q 23  
B1DHFD000015  
UNR9213J0L  
TRANSISTOR  
TRANSISTOR  
2
6
Q 604  
Q 28  
Q 29  
Q 30  
Q 34  
Q 607  
Q 620  
Q 32  
XP0411300L  
XP0421400L  
TRANSISTOR  
TRANSISTOR  
2
3
Q 33  
Q 600  
Q 601  
Q 602  
Q 603  
Q 606  
Q 608  
Q 634  
Q 638  
Q 609  
Q 610  
Q 633  
Q 635  
Q 613  
Q 614  
Q 616  
Q 622  
Q 615  
Q 631  
Q 639  
Q 640  
Q 628  
Q 630  
B1CHRD000001  
B1CFGD000003  
TRANSISTOR  
TRANSISTOR  
2
3
B1MBEDA00017  
TRANSISTOR  
4
DETA144EETL  
B1DHFB000003  
TRANSISTOR  
TRANSISTOR  
1
3
B1DBGD000006  
B1CFGD000004  
TRANSISTOR  
TRANSISTOR  
4
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Q 644  
Q 629  
Q 632  
Q 637  
Q 645  
R 1  
XP0450100L  
TRANSISTOR  
1
1
1
1
2
B1DFGD000032  
B1MBEDA00018  
B1MBEDA00008  
ERJ2GEJ681X  
TRANSISTOR  
TRANSISTOR  
TRANSISTOR  
RESISTOR, 1/16W, 680Ω  
R 258  
R 2  
ERJ2RKF27R4X  
ERJ2RKF54R9X  
RESISTOR, 1/16W, 27.4Ω  
3
5
R 15  
R 16  
R 4  
RESISTOR, 1/16W, 54.9Ω  
R 17  
R 18  
R 35  
R 36  
R 5  
ERJ2RKF39R2X  
ERJ2GEJ151X  
ERJ3GEY0R00V  
RESISTOR, 1/16W, 39.2Ω  
RESISTOR, 1/16W, 150Ω  
RESISTOR, 1/16W, 0Ω  
1
1
3
R 6  
R 11  
R 437  
R 438  
R 12  
R 43  
R 13  
R 14  
R 27  
R 29  
R 31  
R 32  
R 23  
R 636  
R 690  
R 712  
R 731  
R 24  
R 732  
R 25  
R 26  
R 348  
R 609  
R 612  
R 613  
R 749  
R 28  
R 33  
R 39  
R 34  
R 40  
R 42  
R 37  
R 38  
ERJ2RKF2000X  
ERJ2GEJ560X  
RESISTOR, 1/16W, 200Ω  
2
6
RESISTOR, 1/16W, 56Ω  
ERJ3GEYJ100V  
ERJ2RKF1001X  
RESISTOR, 1/16W, 10Ω  
5
2
RESISTOR, 1/16W, 1KΩ  
ERJ2RKF2001X  
ERJ2GEJ562X  
RESISTOR, 1/16W, 2KΩ  
1
6
RESISTOR, 1/16W, 5.6KΩ  
ERJ2GEJ750X  
ERJ2RKF2210X  
RESISTOR, 1/16W, 75Ω  
1
2
RESISTOR, 1/16W, 221Ω  
ERJ2RKF1000X  
ERJ2RKF24R9X  
RESISTOR, 1/16W, 100Ω  
3
4
RESISTOR, 1/16W, 24.9Ω  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 62  
R 231  
R 41  
ERJ2GE0R00X  
RESISTOR, 1/16W, 0Ω  
60  
R 110  
R 111  
R 112  
R 113  
R 114  
R 115  
R 116  
R 117  
R 118  
R 119  
R 120  
R 121  
R 122  
R 123  
R 124  
R 125  
R 126  
R 127  
R 128  
R 129  
R 130  
R 131  
R 132  
R 133  
R 134  
R 135  
R 143  
R 159  
R 223  
R 228  
R 234  
R 235  
R 245  
R 246  
R 311  
R 314  
R 322  
R 323  
R 324  
R 325  
R 332  
R 370  
R 371  
R 376  
R 393  
R 396  
R 410  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 427  
R 428  
R 443  
R 455  
R 475  
R 604  
R 700  
R 702  
R 703  
R 706  
R 722  
R 753  
R 47  
ERJ2RKF80R6X  
ERJ2GEJ103X  
RESISTOR, 1/16W, 80.6Ω  
2
R 48  
R 49  
RESISTOR, 1/16W, 10KΩ  
58  
R 145  
R 188  
R 189  
R 196  
R 219  
R 221  
R 224  
R 229  
R 242  
R 247  
R 283  
R 292  
R 293  
R 300  
R 303  
R 304  
R 306  
R 309  
R 310  
R 320  
R 347  
R 365  
R 372  
R 378  
R 379  
R 380  
R 387  
R 388  
R 402  
R 411  
R 412  
R 431  
R 436  
R 457  
R 458  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 461  
R 462  
R 464  
R 467  
R 469  
R 471  
R 472  
R 615  
R 635  
R 640  
R 641  
R 677  
R 707  
R 711  
R 715  
R 716  
R 721  
R 730  
R 735  
R 736  
R 741  
R 745  
R 50  
ERJ2GEJ222X  
ERJ2GEJ101X  
RESISTOR, 1/16W, 2.2KΩ  
4
R 51  
R 294  
R 295  
R 52  
RESISTOR, 1/16W, 100Ω  
24  
R 202  
R 225  
R 227  
R 241  
R 307  
R 330  
R 331  
R 344  
R 354  
R 397  
R 398  
R 399  
R 429  
R 430  
R 602  
R 603  
R 657  
R 658  
R 659  
R 662  
R 663  
R 664  
R 665  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 53  
ERJ2RKF1002X  
RESISTOR, 1/16W, 10KΩ  
3
R 401  
R 643  
R 57  
D1H82224A024  
ERJ2RKF1501X  
ERJ2GEJ390X  
RESISTOR ARRAY  
1
1
2
R 58  
RESISTOR, 1/16W, 1.5KΩ  
RESISTOR, 1/16W, 39Ω  
R 59  
R 60  
R 61  
ERJ2RKF2550X  
ERJ2GEJ100X  
RESISTOR, 1/16W, 255Ω  
1
R 63  
RESISTOR, 1/16W, 10Ω  
17  
R 315  
R 316  
R 632  
R 633  
R 645  
R 646  
R 675  
R 676  
R 708  
R 709  
R 719  
R 720  
R 727  
R 728  
R 739  
R 740  
R 64  
ERJ2GEJ201X  
D1HG2208A001  
RESISTOR, 1/16W, 200Ω  
4
8
R 66  
R 68  
R 70  
R 76  
RESISTOR ARRAY  
R 77  
R 78  
R 79  
R 104  
R 105  
R 106  
R 107  
R 80  
ERJ2GEJ220X  
RESISTOR, 1/16W, 22Ω  
24  
R 81  
R 82  
R 83  
R 84  
R 85  
R 86  
R 87  
R 88  
R 89  
R 90  
R 91  
R 92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 93  
R 94  
R 95  
R 96  
R 97  
R 98  
R 99  
R 100  
R 101  
R 102  
R 103  
R 108  
R 109  
R 136  
R 137  
R 138  
R 139  
R 140  
R 147  
R 148  
R 166  
R 169  
R 273  
R 280  
R 321  
R 335  
R 366  
R 381  
R 382  
R 451  
R 459  
R 460  
R 686  
R 149  
R 173  
R 150  
R 151  
R 152  
R 153  
R 154  
R 155  
R 192  
R 193  
R 194  
R 195  
R 349  
R 350  
R 351  
R 352  
R 446  
D1HA56080001  
RESISTOR ARRAY  
7
ERJ2GEJ102X  
RESISTOR, 1/16W, 1KΩ  
15  
ERJ2GEJ2R2X  
ERJ2RKF49R9X  
RESISTOR, 1/16W, 2.2Ω  
2
RESISTOR, 1/16W, 49.9Ω  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 447  
R 163  
R 164  
R 165  
R 175  
R 176  
R 177  
R 178  
R 179  
R 180  
R 182  
R 183  
R 184  
R 185  
R 186  
R 187  
R 190  
R 191  
R 218  
R 269  
R 270  
R 271  
R 272  
R 274  
R 275  
R 373  
R 374  
R 474  
R 167  
R 172  
R 174  
R 248  
R 198  
R 217  
R 220  
R 222  
R 262  
R 407  
R 408  
R 452  
R 463  
R 216  
R 276  
R 277  
R 278  
R 279  
R 282  
R 296  
R 297  
R 301  
ERJ2GEJ330X  
RESISTOR, 1/16W, 33Ω  
27  
D1H83304A024  
ERJ2RKF4750X  
ERJ2GEJ1R0X  
RESISTOR ARRAY  
1
1
2
RESISTOR, 1/16W, 475Ω  
RESISTOR, 1/16W, 1Ω  
D1H81034A024  
RESISTOR ARRAY  
9
ERJ2GEJ104X  
RESISTOR, 1/16W, 100KΩ  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 302  
R 308  
R 313  
R 334  
R 336  
R 340  
R 343  
R 362  
R 364  
R 617  
R 619  
R 620  
R 621  
R 650  
R 651  
R 654  
R 656  
R 661  
R 230  
R 232  
R 259  
R 260  
R 261  
R 369  
R 383  
R 384  
R 385  
R 386  
R 389  
R 390  
R 391  
R 403  
R 404  
R 405  
R 406  
R 233  
R 699  
R 757  
R 236  
R 237  
R 238  
R 353  
R 618  
R 649  
R 652  
R 660  
R 689  
R 694  
R 249  
R 250  
ERJ2RKF22R6X  
DEARA8AJ103M  
RESISTOR, 1/16W, 22.6Ω  
1
RESISTOR ARRAY  
16  
ERJ2GEJ472X  
RESISTOR, 1/16W, 4.7KΩ  
3
ERJ2GEJ203X  
ERJ2GEJ106X  
ERJ2GEJ105X  
RESISTOR, 1/16W, 20KΩ  
RESISTOR, 1/16W, 10MΩ  
RESISTOR, 1/16W, 1MΩ  
1
1
8
ERJ2GEJ121X  
RESISTOR, 1/16W, 120Ω  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 266  
R 267  
R 268  
R 449  
R 616  
R 630  
R 670  
R 698  
R 284  
R 285  
R 286  
R 287  
R 288  
R 290  
R 291  
R 799  
R 289  
R 338  
R 346  
R 355  
R 356  
R 357  
R 358  
R 359  
R 666  
R 367  
R 368  
R 395  
R 400  
R 423  
R 634  
R 710  
R 729  
R 601  
R 701  
R 605  
R 608  
R 606  
R 611  
R 638  
R 679  
R 688  
R 607  
R 610  
R 750  
R 614  
R 622  
R 623  
R 624  
R 625  
ERJ2GEJ473X  
RESISTOR, 1/16W, 47KΩ  
8
ERJ2GEJ181X  
ERJ2GEJ221X  
RESISTOR, 1/16W, 180Ω  
1
7
RESISTOR, 1/16W, 220Ω  
ERJ2GEJ471X  
ERJ2GEJ334X  
ERJ2RHD562X  
EXBV8V750JV  
ERJ2GEJ223X  
RESISTOR, 1/16W, 470Ω  
RESISTOR, 1/16W, 330KΩ  
RESISTOR, 1/16W, 5.6KΩ  
RESISTOR ARRAY  
1
1
1
1
5
RESISTOR, 1/16W, 22KΩ  
D1H81024A024  
RESISTOR ARRAY  
2
ERJ2RKF5602X  
ERJ2RKF3901X  
ERJ2GEJ153X  
RESISTOR, 1/16W, 56KΩ  
RESISTOR, 1/16W, 3.9KΩ  
RESISTOR, 1/16W, 15KΩ  
1
1
4
D1ZZ00000046  
ERJ2RHD103X  
ERJ2RKF1003X  
RESISTOR, 1W, 5mΩ  
2
2
5
RESISTOR, 1/16W, 10KΩ  
RESISTOR, 1/16W, 100KΩ  
ERJ2RKF1503X  
RESISTOR, 1/16W, 150KΩ  
3
ERJ3GEYJ3R3V  
D1BDR1000002  
RESISTOR, 1/16W, 3.3Ω  
1
2
RESISTOR, 1/8W, 0.1Ω  
D1BDR2700001  
ERJ2RKF1102X  
RESISTOR, 1/8W, 0.27Ω  
1
1
RESISTOR, 1/16W, 11KΩ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 627  
R 682  
R 628  
R 629  
R 704  
R 705  
R 726  
R 743  
R 631  
R 747  
R 797  
R 637  
R 639  
R 733  
R 642  
R 644  
R 647  
R 648  
R 725  
R 742  
R 744  
R 758  
R 653  
R 655  
R 667  
R 668  
R 669  
R 673  
R 681  
R 674  
R 678  
R 680  
R 693  
R 717  
R 684  
R 738  
R 685  
R 687  
R 691  
R 692  
R 695  
R 696  
R 713  
R 714  
R 737  
R 718  
R 734  
R 723  
R 746  
R 748  
ERJ2RKF1302X  
D1BDR0220001  
RESISTOR, 1/16W, 13KΩ  
2
6
RESISTOR, 1/8W, 0.022Ω  
ERJ2GEJ474X  
RESISTOR, 1/16W, 470KΩ  
3
ERJ2RHD752X  
ERJ2RKF2002X  
RESISTOR, 1/16W, 7.5KΩ  
1
2
RESISTOR, 1/16W, 20KΩ  
ERJ2RKF3002X  
ERJ2RHD102X  
D1BDR0330001  
RESISTOR, 1/16W, 30KΩ  
RESISTOR, 1/16W, 1KΩ  
RESISTOR, 1/8W, 0.033Ω  
1
1
6
ERJ2GEJ684X  
ERJ2GEJ225X  
ERJ6GEYJ561V  
ERJ6GEYJ222V  
RESISTOR, 1/16W, 680KΩ  
RESISTOR, 1/16W, 2.2MΩ  
RESISTOR, 1/10W, 560Ω  
RESISTOR, 1/10W, 2.2KΩ  
1
1
1
2
ERJ2RKF1004X  
RESISTOR, 1/16W, 1MΩ  
2
ERJ2RHD223X  
ERJ2RHD333X  
ERJ2RKF5102X  
RESISTOR, 1/16W, 22KΩ  
RESISTOR, 1/16W, 33KΩ  
RESISTOR, 1/16W, 51KΩ  
1
1
3
ERJ2RHD123X  
RESISTOR, 1/16W, 12KΩ  
2
ERJ2RHD222X  
ERJ2RHD132X  
ERJ2GEJ302X  
ERJ2GEJ154X  
RESISTOR, 1/16W, 2.2KΩ  
RESISTOR, 1/16W, 1.3KΩ  
RESISTOR, 1/16W, 3KΩ  
RESISTOR, 1/16W, 150KΩ  
1
1
1
2
ERJ3GEYJ1R0V  
ERJ2RKF4701X  
ERJ2RKF1502X  
RESISTOR, 1/16W, 1.0Ω  
RESISTOR, 1/16W, 4.7KΩ  
RESISTOR, 1/16W, 15KΩ  
1
1
2
ERJ2RKF2402X  
RESISTOR, 1/16W, 24KΩ  
2
D1BDR0470002  
ERJ2RHD104X  
ERJ2RHD3652X  
RESISTOR, 1/8W, 0.047Ω  
RESISTOR, 1/16W, 100KΩ  
RESISTOR, 1/16W, 36.5KΩ  
1
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
R 751  
R 752  
R 754  
R 755  
R 756  
ERJ2RHD302X  
ERA3YKB104V  
RESISTOR, 1/16W, 3KΩ  
2
2
RESISTOR, 1/16W, 100KΩ  
ERA3YEB333V  
K0D112A00096  
G5BYC0000010  
H0J143500040  
H0J327200115  
H0J250500025  
H2D800400015  
RESISTOR, 1/16W, 33KΩ  
SW  
1
1
1
1
1
1
1
SW 1  
T 1  
X 1  
TRANCE  
OSCILLATOR, 14.318MHz  
OSCILLATOR, 32.768KHz  
OSCILLATOR, 25MHz  
OSCILLATOR, 8MHz  
X 2  
X 4  
X 5  
AUDIO PCB  
C 900  
C 901  
C 902  
C 905  
C 907  
C 909  
C 921  
C 923  
C 926  
C 903  
C 914  
C 922  
C 924  
C 904  
C 908  
C 941  
C 942  
C 906  
C 916  
C 918  
C 910  
C 912  
C 915  
C 917  
C 925  
C 927  
C 928  
C 932  
C 934  
C 913  
C 919  
C 920  
C 933  
C 929  
C 935  
C 930  
C 936  
C 939  
F1G1H120A542  
F1G1H150A542  
F1G1C104A042  
CAPACITOR, 50V, 12pF  
CAPACITOR, 50V, 15pF  
CAPACITOR, 16V, 0.1µF  
1
1
7
F1J0J106A024  
F1G1H102A496  
CAPACITOR, 6.3V, 10µF  
CAPACITOR, 50V, 1000pF  
4
4
F1G1E103A062  
F1G0J224A001  
CAPACITOR, 25V, 0.01µF  
CAPACITOR, 6.3V, 0.22µF  
3
9
F1H1A1050015  
F1G1H1010005  
CAPACITOR, 10V, 1µF  
4
2
CAPACITOR, 50V, 100pF  
F1G1H471A496  
EEFCD0J470ER  
CAPACITOR, 50V, 470pF  
CAPACITOR, 6.3V, 47µF  
1
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
C 940  
C 937  
CN 900  
CN 901  
D 900  
IC 900  
IC 901  
IC 902  
IC 903  
JK 901  
JK 902  
L 900  
L 901  
L 902  
L 903  
Q 900  
Q 901  
R 900  
R 901  
R 903  
R 905  
R 909  
R 910  
R 915  
R 918  
R 926  
R 932  
R 933  
R 934  
R 936  
R 911  
R 916  
R 925  
R 914  
R 939  
R 919  
R 920  
R 930  
R 921  
R 922  
R 923  
R 924  
R 927  
R 931  
R 928  
R 929  
R 935  
R 937  
R 938  
R 940  
F1H0J1050022  
K1MN10BA0070  
K1MY40BA0098  
B0JCMD000014  
C1BB00000868  
C0CBCBC00130  
C1BB00000873  
C0ABBA000093  
K2HC103B0197  
CAPACITOR, 6.3V, 1µF  
CONNECTOR  
CONNECTOR  
DIODE  
1
1
1
1
1
1
1
1
2
IC, AC97 CODEC  
IC, REGURATOR  
IC, AUDIO AMP  
IC, OP AMP  
JK  
J0JDC0000045  
J0MAB0000174  
INDUCTOR  
INDUCTOR  
2
2
UNR9211J0L  
XP0421300L  
ERJ2GEJ220X  
TRANSISTOR  
1
1
2
TRANSISTOR  
RESISTOR, 1/16W, 22Ω  
ERJ2GEJ101X  
ERJ2GEJ330X  
ERJ2GEJ103X  
RESISTOR, 1/16W, 100Ω  
RESISTOR, 1/16W, 33Ω  
RESISTOR, 1/16W, 1KΩ  
1
1
9
ERJ2GEJ473X  
RESISTOR, 1/16W, 47KΩ  
3
ERJ2GEJ472X  
ERJ2GEJ273X  
RESISTOR, 1/16W, 4.7KΩ  
2
3
RESISTOR, 1/16W, 27KΩ  
ERJ2GEJ471X  
ERJ2GEJ222X  
RESISTOR, 1/16W, 470Ω  
1
2
RESISTOR, 1/16W, 2.2KΩ  
ERJ2GEJ683X  
ERJ2GEJ104X  
RESISTOR, 1/16W, 68KΩ  
1
2
RESISTOR, 1/16W, 100KΩ  
ERJ2RKF1002X  
RESISTOR, 1/16W, 10KΩ  
2
ERJ2RKF223X  
ERJ2GEJ102X  
RESISTOR, 1/16W, 22KΩ  
1
2
RESISTOR, 1/16W, 1KΩ  
D1H81034A024  
RESISTOR, ARRAY  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
X 900  
I/O PCB  
C 880  
C 883  
C 884  
C 885  
C 886  
C 887  
C 888  
C 889  
C 890  
C 891  
C 892  
C 893  
CN 880  
CN 881  
CN 882  
CN 883  
D 880  
D 881  
JK 880  
L 880  
H0J245500044  
OSCILLATOR, 24.576MHz  
1
F1H1H104A748  
F1L1E106A017  
F1G1H330A542  
CAPACITOR, 50V, 0.1µF  
CAPACITOR, 25V, 10µF  
CAPACITOR, 50V, 33pF  
1
1
7
F1G1C104A042  
EZASCE101M  
CAPACITOR, 16V, 0.1µF  
CAPACITOR ARRAY  
1
2
K1MN24AA0018  
K1FA209BA004  
K1FB115BA014  
DFJS830YA  
CONNECTOR  
CONNECTOR  
CONNECTOR  
CONNECTOR  
DIODE  
1
1
1
1
1
1
1
1
7
B0JCPD000023  
MA2J72900L  
DIODE  
K2EZ2B000046  
J0JKC0000007  
J0JCC0000186  
JK  
INDUCTOR  
INDUCTOR  
L 881  
L 882  
L 883  
L 884  
L 885  
L 886  
L 887  
PA 880  
R 800  
R 881  
R 882  
R 883  
R 884  
R 885  
R 886  
PAD PCB  
C 800  
C 801  
C 802  
C 803  
C 804  
C 805  
CN 800  
CN 801  
CN 802  
IC 800  
IC 801  
Q 800  
K5J1BB000001  
ERJ2RKF1102X  
D1BDR4700001  
ERJ2RKF75R0X  
POLY SW  
1
1
1
3
RESISTOR, 1/16W, 11KΩ  
RESISTOR, 1/8W, 0.47Ω  
RESISTOR, 1/16W, 75Ω  
ERJ2GEJ222X  
F1G1H681A450  
RESISTOR, 1/16W, 2.2KΩ  
2
2
CAPACITOR, 50V, 680pF  
F1G1E103A062  
F1G1C104A042  
CAPACITOR, 25V, 0.01µF  
CAPACITOR, 16V, 0.1µF  
1
2
F1J0J1060004  
K1MY04BA0104  
K1MN08AA0068  
K1MN13AA0018  
C0EBH0000457  
C1DB00001417  
B1GKCFJN0004  
CAPACITOR, 6.3V, 10µF  
CONNECTOR  
1
1
1
1
1
1
2
CONNECTOR  
CONNECTOR  
IC  
IC, FLAT PAD CONTROLLER  
TRANSISTOR  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Q 801  
R 800  
ERJ2GEJ273X  
ERJ2GEJ822X  
RESISTOR, 1/16W, 27KΩ  
1
2
R 801  
RESISTOR, 1/16W, 8.2KΩ  
R 802  
R 803  
ERJ2GEJ105X  
ERJ2GEJ103X  
RESISTOR, 1/16W, 1MΩ  
1
2
R 804  
RESISTOR, 1/16W, 10KΩ  
R 805  
RA 800  
SW 800  
SW 801  
SW 802  
SW 803  
X 800  
D1H81034A024  
K0ZZ00000618  
RESISTOR ARRAY  
SW  
1
2
EVQPLDA15  
SW  
2
1
H2D400400012  
OSCILLATOR, 4MHz  
SWITCH PCB  
CN 950  
LD 951  
R 951  
K1MN08AA0068  
B3ACB0000105  
ERJ2GEJ221X  
EVQPLDA15  
CONNECTOR  
1
1
1
6
LED  
RESISTOR, 1/16W, 220Ω  
SW 950  
SW 951  
SW 952  
SW 953  
SW 954  
SW 955  
LED PCB  
CN 841  
LD 840  
LD 841  
LD 842  
LD 843  
LD 844  
LD 845  
LD 846  
PORT PCB  
C 851  
SW  
K1MN10AA0058  
B3AGB0000040  
B3ABB0000210  
CONNECTOR  
LED  
1
1
5
LED  
B3ADB0000065  
F1J1A1050021  
LED  
1
3
CAPACITOR, 10V, 1µF  
C 852  
C 854  
C 855  
J0MAB0000146  
J0HABC000004  
INDUCTOR  
3
6
C 856  
C 857  
CA 851  
CA 852  
CA 854  
CA 857  
CA 858  
CA 859  
CN 850  
CN 851  
L 850  
CAPACITOR ARRAY  
K1KBA0A00102  
K1KAA0AA0244  
J0MAB0000116  
DDB5Z031J-L  
CONNECTOR  
CONNECTOR  
INDUCTOR  
1
1
1
2
L 852  
INDUCTOR  
L 853  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TS PS2 PCB  
C 900  
C 907  
C 908  
C 909  
C 901  
C 905  
C 913  
C 902  
C 903  
C 906  
C 910  
C 912  
C 911  
CN 900  
CN 901  
IC 900  
IC 901  
Q 900  
Q 902  
Q 901  
R 900  
R 903  
R 901  
R 904  
R 902  
R 905  
R 906  
R 908  
R 909  
X 900  
F1G1C104A042  
F1G1E472A062  
CAPACITOR, 16V, 0.1µF  
CAPACITOR, 25V, 4700pF  
4
3
F1G1E103A062  
F1G1H681A450  
CAPACITOR, 25V, 0.01µF  
CAPACITOR, 50V, 680pF  
1
2
F1G1H560A451  
CAPACITOR, 50V, 56pF  
2
F1J1A1050021  
K1MN04B00073  
K1KA07BA0014  
C0EBH0000457  
C1DB00001351  
XP0431200L  
CAPACITOR, 10V, 1µF  
CONNECTOR  
CONNECTOR  
IC  
1
1
1
1
1
2
IC  
TRANSISTOR  
UNR9113J0L  
TRANSISTOR  
1
2
ERJ2GEJ102X  
RESISTOR, 1/16W, 1KΩ  
ERJ2GEJ822X  
RESISTOR, 1/16W, 8.2KΩ  
2
ERJ2GEJ303X  
ERJ2GE0R00X  
RESISTOR, 1/16W, 30KΩ  
1
2
RESISTOR, 1/16W, 0Ω  
ERJ2GEJ103X  
H2D100500002  
RESISTOR, 1/16W, 10KΩ  
2
1
OSCILLATOR, 10MHz  
SD PCB  
C 891  
CN 890  
CN 891  
D 890  
Q 890  
R 890  
R 891  
R 892  
F1G1H330A451  
K1NA09E00076  
K1MN12BA0059  
B3ACB0000020  
UNR9113J0L  
CAPACITOR, 50V, 33pF  
CONNECTOR  
1
1
1
1
1
1
1
1
CONNECTOR  
DIODE  
TRANSISTOR  
ERJ6GEYJ101V  
ERJ2GE0R00X  
ERJ2GEJ103X  
RESISTOR, 1/10W, 100Ω  
RESISTOR, 1/16W, 0Ω  
RESISTOR, 1/16W, 1KΩ  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Lawn Mower FDR2560 User Manual
Leviton Telephone LE 47609EMP User Manual
LG Electronics Kitchen Entertainment Center L1717S User Manual
Life Fitness Treadmill tr 8500 User Manual
Lightolier Indoor Furnishings WLRN124120SB User Manual
LST Smoke Alarm M201E 240 DIN User Manual
Makita Home Safety Product BML185 User Manual
Manitowoc Ice Ice Maker K00022 User Manual
Mattel Doll BBV41 0520 User Manual
Melissa Toaster 243 015 User Manual