Marvel 60RD
Installation
Operation &
Maintenance
Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Select Location
The proper location will ensure peak perform-
ance of your drawer refrigerator. Choose a loca-
tion away from heat and out of direct sunlight.
Best performance will be maintained when
installed within the following parameters:
Electrical Connection
Ideal Ambient Temperature Range*
Check the serial nameplate for the correct power
supply. Use only the electrical power supply spec-
ified on the serial nameplate. Do not use an exten-
sion cord.
built-in
55-80°F
55-90°F
freestanding
* Drawer Refrigerator will not perform correctly in ambient temperatures less than 55°F.
Cabinet Clearance
25.82
23.88
21.81
Ventilation is required for the bottom front section of
the unit where the grille is located. Keep this area
open and clear of any obstructions. Adjacent cabi-
nets and countertop can be installed on top, back
and sides of the unit as long as grille and drawer
access remain unobstructed. An opening of 24” is
required between cabinets with a depth of 24”.
23.88
15.13
15.13
Adjacent cabinets and countertop can be installed
on top, back and sides of the unit as long as the
grille and drawer access remain unobstructed.
Ventilation is required for the bottom front section
of the unit where the grille is located. Keep this
area open and clear of any obstructions.
34.00
3.5
Make certain that the leveling legs supplied with
the drawer refrigerator are installed according to
the instructions. Leveling adjustments can be
made by raising or lowering the glides on the bot-
tom of the unit.
Grounding Method
This drawer refrigerator is equipped with a power
supply cord with ground. It must be plugged into a
mating grounding type receptacle in accordance
with the National Electrical Code and applicable
local codes and ordinances. It is the customer’s
responsibility to provide the proper grounding type
receptacle. Do not alter the plug in any way.
DISCONNECT POWER SOURCE BEFORE
ADJUSTING LEVELING LEGS
Important Safety Issue
A cabinet “anti-tip” device is mounted to the back
of your drawer refrigerator. If your installation is a
built-in undercounter application, you do not need
to apply this feature. If your installation is a free-
standing application with no counter top directly
above the top of the drawer refrigerator, you must
apply this feature to prevent the unit from tipping
forward when the drawers are pulled out. The
“anti-tip” device is attached at the back of each
cabinet. Please see installation instructions sup-
plied with the “anti-tip” device.
THIS UNIT SHOULD NOT, UNDER ANY
CIRCUMSTANCES, BE UNGROUNDED.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Control Panel
The temperature of your drawer unit ranges from
32°F to 47°F (0°C to 8°C. The temperature can be
adjusted using the control panel located on the
inside of the top drawer. To change the tempera-
ture setting, press the warmer or cooler pads until
the display shows the desired temperature. After a
few seconds the display will return to the actual
temperature of the unit. An empty unit will stabilize
in six to eight hours.
TEMPERATURE CONTROL
COOLER
WARMER
Your drawer refrigerator’s control leaves the facto-
ry preset to display its temperature in degrees
Fahrenheit. To change the display to show Celsius
temperatures, simply press the warmer and cold-
er key pads simultaneously. The display will
change within a few seconds.
The on/off key pad stops and starts the cooling of
the unit. This can be used when your drawer
refrigerator will not be used for extended periods
of time. The LED light will continue to operate
when the drawers are opened as long as the unit
is connected to a power source.
ON
OFF
At time of initial start up the control panel display
will show “OR” for “Out of Range” until the unit
reaches the desired temperature. At any time the
unit’s interior temperature reaches 9 degrees
below or above its setpoint this code will also be
displayed.
Gastronorm Container Systems
For additional convenience, optional Gastronorm
food storage containers can be purchased from
your dealer. These stainless steel containers can
be used to easily access smaller food items and
are dishwasher safe. For further information visit
Drawer Organizer
The Drawer Organizer is designed to be fully
adjustable to compensate for bottles and other
items of different sizes. The drawer Organizer can
be adjusted left and right, up and down by turning
the knob counter clockwise.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING OF YOUR DRAWER REFRIGERATOR
Condenser
The condenser tubing inside the cabinet does not
require frequent cleaning; however, satisfactory
cooling depends on adequate ventilation over the
coils. Be sure that nothing obstructs the required
air flow openings in front of the cabinet. At least
once or twice a year brush or vacuum lint and dirt
from the grille. Also at least once or twice a year
brush or vacuum lint and dirt from the condenser
for efficient performance by unscrewing the grille
on the bottom front of the cabinet.
Interior
Care of Unit
1. Avoid leaning on the drawer fronts, you may
Clean the drawer gaskets as well as inside the
drawers with mild soap and water. Do not use an
abrasive powder, solvent, polish cleaner or undi-
bend the door hinge or tip the unit.
luted detergent.
2. Exercise caution when sweeping, vacuuming,
or mopping near the front of the unit. Damage
to the grille can occur.
Cabinet
The painted cabinet can be washed with mild
soap and water and thoroughly rinsed with clear
water. Never use abrasive scouring powders.
Care and Cleaning of Your Drawer Refrigera-
3. Periodic cleaning of the inside of the unit. (See
tor section).
Interior
Wash interior compartments with mild soap and
4. Periodic checking and/or cleaning of the front
water. Do not use an abrasive powder, solvent,
grille and condenser coils as needed.
polish cleaner or undiluted detergent.
Normal Responsibilities of the Owner
• All freight charges
Door Gasket
The vinyl gasket may be cleaned with mild soap
and water, a baking soda solution or a mild scour-
ing powder.
• Damage sustained in transit
• Mileage charge(s) for service calls
• Proper installation including installation of lev-
eling legs.
• Leveling of unit.
• Alterations to original equipment
• Cleaning and normal maintenance outlined in
this manual.
Help Prevent Tragedies
Each year, children die because they climb inside
a discarded refrigeration product, get trapped
inside and suffocate. Take precautions to prevent
such tragedies by removing the door, taping or
chaining it shut before discarding.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 1:
Wood Screws Required
1. A #8 pan head wood screw should be used to
properly secure the overlay panel. A total of 8
screws will be needed.
2. Use only pan head screws.
5/16 PHILLIPS HEAD SCREWS
HOLDING DRAWER FRONT
3. Do not select a screw that is longer than the
wood thickness at the screw locations.
4. Use recommended pilot holes for the frame
material (see chart below).
Pilot Hole Drill Sizes for Wood Screws
Wood Screw Size
GASKET
Work Material
Hardwood
Softwood
8
3/32
5/64
Step 2:
Remove Drawer Fronts
(Note: The overlay panel may be installed without
removing the drawer fronts from the drawer bod-
ies, but the full drawer assembly is not as easy to
handle as the drawer front alone.)
1. Remove drawer from unit. Begin by pulling out
the drawer. Locate the drawer lock which can be
found on the outside of the cabinet slide (fig. 1).
Push the back of the drawer lock forward and
then down, releasing the drawer from the cabinet
slide (fig. 2). Repeat this on the opposite side of
the drawer. Lift the drawer up from the slides at
90° to fully extricate the drawer from the cabinet
(fig. 3).
figure 2
2. Remove drawer fronts. Do this by removing
the 8 phillips screws and washers securing the
drawer front to the drawer body. Mark lightly with
an erasable marker the position of the stainless
drawer liner as it secured to the stainless drawer
before removing screws.
figure 1
3. Remove the gasket from the drawer front. Do
this by pulling the gasket out of the channel that
holds it to the drawer front .This will expose the
clearance holes for mounting the overlay panel.
figure 3
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS
Step 3:
Sizing the Overlay Panel
23.63
14.63
15.19
7.59
.56
.56
11.81
23.06
Step 6:
Reinstall the Drawer
1. Fully extend drawer slides and place drawer on
slides. Be sure that drawer sits evenly on both
slides.
Step 4:
Attaching the Overlay Panel to the Door
1. Set overlay panel on drawer front face and
align edges. Clamp panel in position and mark
pilot hole locations. See step 3 for nominal size
and hole locations. Drill pilot holes (remove panel
if necessary, re-align and re-clamp overlay to
drawer face).
2. Lock drawers into drawer slides. Push drawer
locks down and then back to relock the drawer
into the slide.
2. Insert wood screws through clearance holes
and tighten to secure overlay panel.
Step 7:
Adjust Drawer Front
1. Adjust drawer front to achieve a 1/8" gap from
the top of the drawer front to the top of the cabi-
net or (for bottom drawers) 1/8" from the top of
the drawer front to the bottom of the top drawer,
the drawer front should be centered between the
cabinet edges.
3. Reinstall gasket into channel. Make sure the
corners are inserted fully.
Step 5:
Reattach Drawer Front to Drawer Body
1. Align mounting holes on drawer body with
mounting holes on drawer front. Align the door
liner to the front flanges by using the erasable
marker alignment lines that were applied prior to
removing the door from the drawer. Reinstall
phillips head screws and washers. Snug down,
but do not tighten fully, final adjustment of drawer
front will be done after reinstalling the drawer.
2. Fully tighten phillips head screws.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
CORRECTION
Odor in cabinet
Noisy operation
Unit vibrates
• Clean inside of unit. See “Care and Cleaning” pg. 7.
• Adjust leveling legs. See leveling leg instructions.
• Adjust leveling legs. See leveling leg instructions.
• Rebuild floor or move to a different location.
• Replace LED light.
• Unit interior needs cleaned.
• Unit not level.
• Unit not level.
• Weak floor.
Interior light not working
Appliance will not run.
• LED light burned out.
• No power at outlet.
• Control Panel turned “OFF”.
• Test outlet with lamp.
• Turn unit on with on/off pad on Control Panel.
• Plug unit into power source.
• Line Cord not plugged into power
source.
• House fuse blown.
• Reset house fuse.
Appliance runs too long.
• Prolonged door openings.
• Control Panel set too cold.
• Condenser needs cleaning.
• Too many door openings.
• Prolonged door openings.
• Hot, humid weather increases
condensation.
• Reduce number and/or duration of door openings.
• Raise temperature of unit via Control Panel.
• Clean condenser. See “Care of Unit” pg 7.
• Reduce number and/or duration of door openings.
• Reduce number and/or duration of door openings.
Moisture collects inside of unit
• As humidity decreases, moisture will disappear.
• Move unit to cooler location.
• As humidity decreases, moisture will disappear.
• Move unit to cooler location.
Moisture collects on outside
surface of the unit.
• Hot, humid weather increases
condensation.
• Reset to slightly warmer temperature.
• Reset control to desired temperature.
• Recheck with second thermometer.
• Control improperly set.
• Control improperly set.
• Faulty thermometer.
Interior too hot/too cold
Diagnostic LED
In the back in the grille there is a diagnostic/status
LED. This led is used to help diagnosis any problems
with the unit and to tell its status.
LED Status
Not on
Code/Problem
Unit does not have power
Continuously on
Unit is "ON" and operating correctly
For shorted or open thermistor
Disconnected Display Board
Compressor is locked out
1 Blink and pause
2 Blink and pause
3 Blink and pause
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING SERVICE
Before Calling for Service
Before calling for service, check the following
items:
3. In all correspondence regarding service, be
sure to give the model number, serial num-
ber and proof of purchase.
• Make sure unit is plugged into outlet.
4. Try to have information or description of the
nature of the problem, how long the unit has
been running, the room temperature and
any additional information that may be help-
ful in quickly solving the problem.
• Check the outlet for power. Test outlet with
lamp to make certain outlet has power.
• Make sure drawer refrigerator is “ON”. Dis-
play will show.
Every new drawer refrigerator that leaves the factory
contains this Owner's Guide. Keep this Owner's
Guide in a safe place for convenient reference.
• Make certain unit is level from front to back
and side to side.
• Use troubleshooting guide, page 7 for other
diagnosis.
SEND IN YOUR WARRANTY RECORD CARD
IMMEDIATELY AFTER TAKING DELIVERY OF
YOUR DRAWER REFRIGERATOR.
If you are not able to correct the problem, contact
your dealer or the manufacturer. Be sure to have
the model number and the serial number handy
before you call. The model and the serial number
are located somewhere on your drawer refrigera-
tor.
For Your Records
How to Obtain Service
Date of Purchase
Dealer's Name
Your drawer refrigerator requires little service
because the best and most up-to-date materials,
equipment and quality control methods are
employed throughout the manufacturing process.
Dealer's Address
If trouble occurs during normal operation, read
"Things to remember" section first and, if neces-
sary, check the troubleshooting guide. If service
becomes necessary:
Dealer's city
Dealer's State
Zip
1. Contact the dealer where your appliance
was purchased or the manufacturer for the
name of the nearest authorized service rep-
resentative. The service representative will
have full authority to make any repairs
deemed necessary.
Appliance Serial Number
Model Number
Date Warranty Card Mailed (within 10 days of purchase)
2. If you are in an area where there is no serv-
ice representative, write or call the manufac-
turer directly. We will make recommenda-
tions as to the proper procedure for correc-
tion. Service work and replacement parts, if
required, will be provided as covered by your
limited warranty.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Entire Product
Parts or Service
Limited One Year Parts and Labor Warranty
Marvel warrants that it will supply all necessary
parts and labor to repair or replace in the end
user's home or office, any component which
proves to be defective in material or workmanship,
subject to the condition and exclusions stated
below, for a period of one year from the date of
purchase by the end user.
Not Supplied or Designated by Marvel
The above warranties also do not apply if:
The original bill of sale, deliver date or serial num-
ber cannot be verified.
Defective parts are not returned for inspection if so
requested by Marvel.
The refrigeration equipment is not in the posses-
sion of the original end use purchaser.
Additional Second Through Fifth Year
Limited Parts Only Warranty
During the four years following expiration of the
one year limited warranty, Marvel will supply
replacement parts for the hermetically sealed
refrigeration system which consists of the com-
pressor, condenser, drier, accumulator, by-pass
valve, connecting tubing and the evaporator that
are proven to be defective due to workmanship or
materials subject to the conditions and exclusions
below.
The warranties set forth herein are the only war-
ranties extended by Marvel Industries. Any implied
warranties, including the implied warranty of mer-
chantability, are limited to the duration of these
express warranties. In no event shall Marvel
Industries be liable for any consequential or inci-
dental damages or expenses resulting from
breach of these or any other warranties, whether
express or implied.
The above warranties do not cover:
Some states do not allow the exclusion or limita-
tion of consequential damages or a limitation on
how long an implied warranty lasts, so the above
exclusion or limitation may not apply to you. This
warranty gives you specific legal rights and you
may have other rights that may vary from state to
state.
• Shipping costs of replacement parts or returned
defective parts.
• Customer education or instructions on how to
use the appliance.
• Any content loss due to product failure.
• Removal or installation.
No person, firm, or corporation is authorized to
make any other warranty or assume any other
obligation for Marvel Industries. These warranties
apply only to products used in any of the fifty
states of the United States and the District of
Columbia.
Nor do the above warranties cover failure of this
product or its components due to:
1.Transportation or subsequent damages.
To obtain performance of this warranty, report any
defects to:
2.Use commercially or use other than normal
household or small office.
Marvel Industries
P.O. Box 997
Richmond, Indiana 47375-0997
Phone: 765-962-2521
3.Improper installation, misuse, abuse, accident
or alteration, use on wiring not conforming to
electrical codes, low or high voltages, failure to
provide necessary maintenance, or other unrea-
sonable use.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
11
Download from Www.Somanuals.com. All Manuals Search And Download.
W W W . M A R V E L I N D U S T R I E S . C O M
Phone: (765) 962-2521 Fax: (765) 962-2493
MARVEL
I
N
D
U
S
T
R
I
E
S
233 Industrial Parkway
P.O. Box 997
Richmond, IN 47375-0997
41009143A
Download from Www.Somanuals.com. All Manuals Search And Download.
|