310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 1
!
!
WARNING DANGER
EN
OWNER’S MANUAL and SAFETY INSTRUCTIONS
BLADES ARE EXTREMELY SHARP.
TO AVOID INJURY WHEN UNPACKING
THE HEDGE TRIMMER,
Double Edged (Models DEHT19, DEHT24)
Electric Hedge Trimmers
DO NOT GRASP THE BLADES.
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 3
II. GENERAL SAFETY RULES
12) Do not overreach.
Keep proper footing and balance at all times.
13) Maintain tool with care.
Warning: When using electric tools, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, electric shock and
personal injury.
Keep cutting tools sharp and clean for better and
safer performance. Follow instructions for
lubrication and changing accessories. Inspect tool
cord periodically and if damaged have it repaired
by Mantis. Inspect extension cords periodically
and replace, if damaged. Keep handles dry, clean
and free from oil and grease.
Read all these instructions before operating this
product and save these instructions.
For safe operations:
1) Keep work area clean.
14) Disconnect tools.
Cluttered areas and benches invite injuries.
2) Consider work area environment.
Do not expose power tools to rain. Do not use
power tools in damp or wet locations. Keep work
area well lit. Do not use power tools where there
is risk of fire or explosion.
When not in use, before servicing and when
changing accessories such as blades, bits and
cutters.
15) Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
3) Guard against electric shock.
Avoid body contact with earthed or grounded
surfaces e.g. pipes, radiators, ranges, refrigerators.
4) Keep children away.
Do not let visitors touch the tool or extension
cord. All visitors should be kept away from area.
5) Store idle tools.
When not in use, tools should be stored in a dry,
high or locked up place, out of reach of children.
6) Do not force the tool.
16) Avoid unintentional starting.
Do not carry a plugged in tool with a finger on the
switch. Ensure switch is off when plugging in.
17) Use outdoor extension leads.
When tool is used outdoors, use only extension
cords intended for outdoor use.
18) Stay alert.
Watch what you are doing . Use common sense.
Do not operate tool when you are tired.
19) Check damaged parts.
It will do the job better and safer at the rate for
which it was intended.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operated properly and
perform its intended function. Check for
alignment of moving parts, free running of moving
parts, breakage of parts, mounting and any other
conditions that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by Mantis unless otherwise
indicated in this instruction manual. Have
defective switches replaced by Mantis. Do not use
the tool if the switch does not turn it on and off.
20) Warning.
7) Use the right tool.
Do not force small tools or attachments to do the
job of a heavy duty tool. Do not use tools for
purposes not intended; for example, do not use
circular saws to cut tree limbs or logs.
8) Dress properly.
Do not wear loose clothing or jewelry that can be
caught in moving parts. Rubber gloves and non-
skid footwear are recommended when working
outdoors. Wear protective hair covering to contain
long hair.
9) Use safety glasses.
Use face or dust mask if the cutting operation is
The use of any accessory or attachment, other
than those recommended in this instruction
manual, may present a risk of personal injury.
21) Have your tool repaired by a qualified person.
This electric tool conforms to relevant safety
requirements. Repairs should only be carried out
by qualified persons using original spare parts,
otherwise this may result in considerable danger
to the user.
dusty.
10) Do not abuse the cord.
Never carry the tool by the cord or yank it to
disconnect if from the socket. Keep the cord away
from heat, oil and sharp edges.
11) Secure work.
Use a vice to clamp the frame bar while adjusting
blades. It is safer than using your hand and it frees
both hands to operate the tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 4
!
!
WARNING
DANGER
!
!
WARNING
DANGER
TO REDUCE THE POTENTIAL FOR
ACCIDENTS, COMPLY WITH THE
SAFETY INSTRUCTIONS IN THIS
MANUAL. FAILURE TO COMPLY MAY
RESULT IN SERIOUS PERSONAL
INJURY AND OR EQUIPMENT AND
PROPERTY DAMAGE.
THIS SYMBOL POINTS OUT
IMPORTANT SAFETY INSTRUCTIONS.
!
WHEN YOU SEE THIS SYMBOL,
HEED IT’S WARNING!!
STAY ALERT!!
!
A. SAFETY DECALS AND MOLDED SYMBOLS
Important parts of the safety system incorporated in
Double Edge trimmers are the warning and
informational decals and molded-in symbols found on
various parts of the trimmer. These decals must be
replaced in time due to abrasion, etc.
It is your responsibility to replace thedecals or molded
housing when they become hard to read. The locations
of these safety features are shown below. See page 11
for their part numbers when ordering replacements.
Double Edge Trimmer
Loop Handle
Rear Handle
Guard
On/Off Switch
On/Off
Switch
Safety Symbols
(Molded into Part No. 310400 Main Housing Set}
!
B. SAFETY SYMBOLS IDENTIFICATION
1
2
3
4
WHAT THE SYMBOLS MEAN:
1. Read the instructions.
2. Do not expose to rain.
3. Remove plug from main (electric
power source) immediately if cable is
damaged or cut.
4. Double insulated.
!
!
WARNING DANGER
IF TRIMMER IS USED IMPROPERLY OR SAFETY PRECAUTIONS ARE NOT FOLLOWED,
THE USER RISKS SERIOUS INJURY TO THEMSELVES AND OTHERS.
READ AND UNDERSTAND THE RULES FOR SAFE OPERATION AND ALL
INSTRUCTIONS IN THIS MANUAL.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 5
have come to a complete stop before letting go of a
handle.
C. SPECIAL SAFETY RULES
!
1. Read and understand the owner’s manual. Pay
particular attention to all sections regarding safety.
3. Maintain a firm footing and good balance; do not
overreach while trimming. Before you start to trim,
check the work area for obstacles that might cause
you to lose your footing, balance or control of the
machine.
2. Always keep a firm grip on both handles while the
blades are moving and/or the motor is running. On
Double Edged units, one hand grasps the front
‘loop’ handle, while the other hand grasps the rear
handle.
4. Keep area clear of children, pets, and bystanders.
BE AWARE!! The blades coast after triggers are
released or motor is switched off. Make sure blades
jammed material before switching the motor off and
making sure the blades have stopped completely.
D. WARNINGS — DON’TS
!
Don’t use trimmer with one hand, keep both hands on
handles with fingers and thumbs encircling the handles,
while blades are moving, and motor is running.
Don’t over-ride safety features.
Don’t allow children or incapable people to operate this
trimmer.
Don’t overreach or stand on unstable support. Do not
stand on the top of a ladder while trimming. Use proper
equipment for reaching higher heights. Keep a good
footing at all times.
Don’t operate this hedge trimmer while under the
influence of alcohol or drugs.
Don’t ever grasp cutting blades for any reason.
Don’t attempt to repair this hedge trimmer. Have
repairs made by Mantis. See that only original Mantis
parts are used.
Don’t attempt to clear cut material while blades are
moving, and the motor is running. Never try to remove
Always keep children, pets, and incapable persons
away.
E. WARNINGS — DO’S
!
Always read and follow all instructions.
Always use trimmer properly. Cut only types and size
of growth described in the Trimming section of this
manual. Overloading or abusing your hedge trimmer
can cause premature failure and can result in injury.
Use common sense.
Always stay alert. Watch what you are doing and use
common sense. Do not operate unit when fatigued.
Always dress properly. Do not wear loose clothing or
jewelry, they might get caught in moving parts. Use
sturdy proper fitting, non-slip gloves. Gloves reduce the
transmission of vibration to your hands. Prolonged
exposure to vibration can cause numbness and other
ailments. Wear non-skid foot wear to ensure secure and
proper footing.
Always keep a safe distance between two or more
operators when working together simultaneously.
Always inspect your unit before each use and ensure
that all handles, guards, safety devices and fasteners are
secure, operating, and in place.
Always wear ear and eye protection. Eye protection
must meet ANSI Z 87.1. To avoid hearing damage we
recommend hearing protection be worn whenever using
the equipment.
Always maintain and examine your trimmer with care.
Follow maintenance instructions given in manual.
Always store trimmer in a sheltered area (a dry place)
not accessible to children. The hedge trimmer should
not be stored in a house.
Always keep both hands on both handles when
trimmer is running. Severe injuries can result if you
try to use the hedge trimmer with only one hand or
with an insecure grip.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 6
III. UNPACKING AND ASSEMBLY INSTRUCTIONS
!
!
WARNING DANGER
!
!
WARNING DANGER
BLADES ARE EXTREMELY SHARP. TO
AVOID INJURY WHEN UNPACKING THE
HEDGE TRIMMER, DO NOT GRASP THE
BLADES.
IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR LOCAL DEALER
Your Mantis hedge trimmer has been assembled for
you at the factory. Before operating be sure all fasteners
are secure, and all guards and safety devices are in place
and operating properly.
IV. OPERATION
!
!
WARNING DANGER
THE OPERATOR OF THIS HEDGE TRIMMER IS RESPONSIBLE FOR
ACCIDENTS OR HAZARDS OCCURRING TO HIMSELF, OTHER
PEOPLE OR THEIR PROPERTY.
A. INSTRUCTIONS FOR PROPER OPERATION
Securing the
extension cord.
!
!
WARNING DANGER
Bend the extension
cord about 6" from
the plug end. Push
that bend through
the oblong opening
in the back of the
handle. Then loop
the bend under the
cord retaining clips
as shown. This will
prevent the extension
cord from detaching
from the hedge
BLADES COAST AFTER RELEASING THE
SWITCHES
KEEP A FIRM GRIP WITH ONE HAND
ON EACH HANDLE WHILE BLADES ARE
MOVING AND/OR MOTOR IS
RUNNING.
DO NOT STAND ON THE TOP OF A
LADDER WHILE TRIMMING.
MAKE SURE YOUR LADDER OR OTHER
SUPPORT IS STABLE AND ON FIRM
GROUND.
trimmer plug.
KEEP A SURE FOOTING.
DO NOT OVERREACH.
Misuse of this Hedge Trimmer will void the warranty.
ie: cutting hedges or shrubs over 1/2" in diameter or
foreign objects such as wires, rocks, or fences. Before
trimming check work area for foreign objects such as
wires, cords, glass, fences, or rocks. Be sure to remove
any foreign objects from the work area. Failure to
properly maintain this hedge trimmer will void the
warranty.
IF YOUR TRIMMER BECOMES JAMMED,
TURN OFF THE HEDGE TRIMMER.
MAKE SURE BLADES HAVE STOPPED
COMPLETELY, THEN REMOVE
THE OBSTRUCTION.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 7
1. Read care and safety instructions carefully before
attempting to use this trimmer. Only after you are
familiar with your hedge trimmer and all of its controls
and the functions should you start the trimmer.
5. Keep extension cord behind trimmer. Never drape
extension cord over hedge being trimmed. On 115V
units, use 16 gauge wire extension cord up to 100 feet.
Over 100 feet use 14 or heavier gauge wire or extension
cord. The use of light gauge lamp cords or sizes lighter
than those specified above will result in loss of power,
possible motor failure, overheating of cord and the
possibility of fire.
2. Before plugging into an electric circuit, be sure that the
voltage supply is as specified on hedge trimmer.
Models DEHT19 and DEHT24 are rated at 390 watts at
115 volts.
6. Warning! These trimmers have been designed so they
can only be operated when using both hands. Do not
attempt to override this important safety feature in any
way.
3. Be sure the switches are in the “off” (not depressed)
position before connecting unit to the applicable
current. (120V AC or 220V/240V AC.) Do not carry a
plugged -in trimmer with a finger on the switch.
7. Hold trimmer firmly. For Double Edge Models, you can
place either hand on either handle. Squeeze both
switches.
4. The electricity for this hedge trimmer should be
supplied through a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. These
protective devices are also known as Residual Current
Circuit Breakers (RCCBs) or Earth Leakage Circuit
Breakers (ELCBs).
Tilt trimmer so cutting tooth is angled slightly toward
the hedge or shrub and proceed to cut. Use
overlapping sweeping motions away from your body to
achieve a safe and even cut. The unit is designed to cut
any type of hedge or shrub; however, thickness of
cut should not exceed 1/2 inch
in diameter.
1/2"
V. MAINTENANCE
Remove the plug from the socket before carrying out any adjustment, servicing, or maintainence.
A. LUBRICATION AND MAINTENANCE
4. Gear housing and motor bearings have been
1. A few drops of light (#10) oil should be placed on
the back edge of each blade at each adjusting
screw after approximately every four hours of
normal operation.
permanently lubricated with a special grease
which should last for the life of the trimmer. When
blades are replaced, or any other time that the
bottom cover plate is removed, the grease must be
checked for proper amount (approximately 3/4 full
in the area of the gears), and a new gasket and new
screws must be used to insure proper seating of
cover plate. Use only Lubrico M3-3K9K grease in
the gear housing. Lubrico M24M is to be used on
the motor bearings.
2. To obtain trouble free trimming, it is necessary to
keep the blades lubricated and clean. The gum
that collects and builds up on the blades can be
removed with 50-50 mixture of kerosene and #10
oil. Since a petroleum product can shorten the life
of some plastics, it is necessary to remove excess
oil-kerosene mixture from the plastic parts. Blades
must be clean before they can be adjusted.
5. Before each use, inspect to be sure handles, safety
devices and fasteners are secure and in place, and
cord is not frayed. If the supply cord is damaged, it
must be replaced by the manufacturer, its service
agent or similarly qualified person in order to
avoid a hazard.
Caution! Kerosene and oil are flammable.
3. A few drops of light (#10) or 3-in-1 oil should be
put in the hole indicated on the bottom cover
plate. This is necessary only at the beginning of a
day’s operation.
B. SERVICE MAINTENANCE GUIDE
Area
Maintenance
Frequency
Monthly
Gear Housing
Check Grease
Blades
Fasteners
Labels
Handles
Inspect / Clean / Lubricate
Inspect / Tighten / Replace
Inspect / Replace
Inspect / Replace
Inspect / Replace
After Each Use
Before Each Use
Before Each Use
Before Each Use
Before Each Use
Guards / Safety Devices
IMPORTANT- Time intervals shown are maximum. Actual use and your experience will determine the
frequency of required maintenance.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 8
VI. SERVICE
A. TROUBLE SHOOTING
Problem
Cause
Remedy
1. Blades don’t cut cleanly.
Blades are dull or not adjusted
properly.
Have blades sharpened and
adjusted.
2. Blades don’t move when
turned on.
Blades are adjusted too tight.
Worn brushes.
Re-adjust blades following
service instructions.
3. Excessive electrical arcing
from vents in top of
trimmer.
Replace brushes - follow
service instructions.
B. BLADE ADJUSTMENT
The care and adjustment of the blades is very important
to the efficient operation of the trimmer and especially
to the long life of the motor.
Double Edged trimmer can just be moved with
finger pressure. (A .0015" (1 1/2 thou.) feeler gauge
just slips under the blade guard or comb when
properly adjusted.) Tighten the locknuts while
holding the screw stationary in its correct adjusted
position. Re-check to make sure the blade guard or
comb can still be moved.
Make sure the trimmer is NOT plugged in!
1. Turn trimmer upside down. Place trimmer in vice,
clamping on the sides of frame bar. Be careful!
Blades are sharp!
4. Repeat Step 3 on each screw in turn until all are
correctly adjusted.
2. Using a 7/16” wrench, loosen all blade locknuts
and unscrew the large head screws by two turns.
NOTE: CORRECT BLADE ADJUSTMENT CAN
ONLY BE ACHIEVED ON CLEAN, OILED BLADES.
3. Starting with the screw nearest the gear housing,
tighten the screw until the protective comb of the
!
!
WARNING DANGER
KEEP HANDS AWAY FROM THE BLADES WHILE SERVICING THE HEDGE TRIMMER.
BE SURE TRIMMER IS SECURED, UNPLUGGED, AND BLADES ARE GUARDED
WHILE MAKING ADJUSTMENTS
DOUBLE EDGED
8
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 9
VII. PARTS EXPLOSION
Double Edge Assembly
KEY # PART #
DESCRIPTION
QTY.
1
2
2
3
310100
16-54B
16-54B
300300
NA
1
6
5
1
1
1
1
1
1
1
1
1
1
3
2
2
1
Gear Housing Assembly (including pressed in pins)
Nut Lock 1/4-28 whiz Flange (for model DEHT24) 24” DE
Nut Lock 1/4-28 whiz Flange (for model DEHT19) 19” DE
Frame Bar Support
4
Loop Handle Assembly (See individual part numbers)
Frame Bar assembly (for model DEHT24) 24” DE
Frame Bar assembly (for model DEHT19) 19” DE
Inside Blade (for models DEHT24) 24” DE
Inside Blade (for model DEHT19) 19” DE
Outside Blade (for model DEHT24) 24” DE
Outside Blade (for model DEHT19) 19” DE
24” Comb (for model DEHT24) 24” DE
19” Comb (for model DEHT19) 19” DE
Large Head Phillips Screw (for model DEHT24) 24” DE
Large Head Phillips Screw (for model DEHT19) 19” DE
Screw, Plas-Tite #8 x 3/4”
5
5
6
6
7
7
8
310320
310315
24-2D
19-2D
24-1D
19-1D
24-42
8
19-42
9
9
10
11
16-54A
16-54A
310500
310505
Screw, 1/4-28 x 1” Large Head
9
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 10
Gear/Motor Assembly
KEY # PART #
DESCRIPTION
QTY.
1
1
310100
16-57A
310407
D16-71
16-62
Gear Housing Assembly
Gear Housing Cover Plate
Grommet Rubber
Gasket Cover Plate
Eccentric Gear
2
3
1
4
1
1
4
5
6
7
D16-59
16-64
1
1
Cluster Gear
Connecting Rod
8
9
16-65
16-67
1
1
Spacer Connecting Rod
Felt
10
11
12
13
14
15
17
18
19
20
21
22
16-81-1
310503
3042
D16-56F
310903
310108
16-69D
310901
16-69E
3025
8
2
4
1
1
1
1
1
1
2
2
2
Screw 6-32 x 5/16
Motor Bolt 8-32 x 2 1/2
Machine Screw
Wear Plate
Stator 120V (For Models DEHT24 and DEHT19)
Motor Housing Base and Cap Set with Brush Holder
Bearing Lower
Armature 120V (For Models DEHT24 and DEHT19)
Bearing Upper
Brush Holder (not shown)
Brush
Brush Retaining Plate
310105
3026
10
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 11
Double Edge Front Loop Handle Assembly
KEY # PART #
DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
3033
1
1
1
1
1
3
2
1
Switch Normally Open
Switch Normally Closed
Loop Handle Trigger Set
Loop Handle Set
310405
310219
310203
310207
310504
310500
310218
Shield
Screw Plasti-Tite #8 x 1”
Screw Plasti-Tite #8 x 3/4”
Loop Handle Trigger Strap
Main Housing Assembly
KEY # PART #
DESCRIPTION
QTY.
1
2
5
6
310450
310403
310437
310209
3033
1
1
1
1
1
1
6
3
1
1
1
Main Housing Set Mantis
Housing Brush Cap Cover Plate
PC Board Assembly (for Models DEHT19, DEHT24)
Trigger Rear Housing
Switch Normally Open
Switch Normally Closed
7
8
310405
9
310500 Screw, Plasti-tite #8 x 3/4”
Screw, Plasti-tite #8 x 1”
120V Cord Assembly
Warning Label
10
11
12
13
310504
310410
310600
310217
Grommet, Conduit
11
Download from Www.Somanuals.com. All Manuals Search And Download.
310706 Electric Trimmer EN_310700 Electric Trimmer.qxd 7/28/10 3:01 PM Page 12
VIII. SPECIFICATIONS
The A-weighted emission sound pressure level at the
Cutting Length
cm (in.)
Weight
kg (lb)
Model
PA
operator position has been measured at: L = 80 dB(A).
These measurements were made in accordance with
EN ISO 11201:1996 under no-load conditions.
DEHT19
DEHT24
48 (19)
61 (24)
3.89 (8.6)
4.04 (8.9)
The Hand-Arm weighted r.m.s. vibration measured at
the handles in accordance with EN 50144-1 part 13.3
All listed hedge trimmers are rated for
230 volts AC at 50 hertz.
2
at rated conditions, no load was:1.0 m/s .
MANTIS HEDGE TRIMMER LIMITED WARRANTY
MANTIS extends this limited warranty against defects in
material and workmanship for a period of two (2) years for
normal residential purposes and one (1) year for commercial
use from the date of purchase, to the first retail purchaser and
each subsequent owner, during the warranty period. This
warranty covers all portions of the MANTIS HEDGE TRIMMER.
altered, used for other than normal or intended purposes. This
warranty does not cover damage due to normal wear and tear.
You must maintain your MANTIS HEDGE TRIMMER by
following the maintenance procedures described in the owner’s
manual. Such routine maintenance, whether performed by you
or a dealer, is at your expense.
MANTIS will repair or replace, at its option, any part or parts
of the product proven to be defective in material or
MANTIS MAKES NO EXPRESS OR IMPLIED WARRANTIES
OR REPRESENTATIONS EXCEPT THOSE CONTAINED
HEREIN. THE DURATION OF ANY IMPLIED WARRANTY,
INCLUDING MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IS LIMITED TO THE DURATION
OF THIS WRITTEN LIMITED WARRANTY. MANTIS
DISCLAIMS ALL LIABILITY FOR INDIRECT, INCIDENTAL
AND/OR CONSEQUENTIAL DAMAGES IN CONNECTION
WITH THE USE OF THE MANTIS PRODUCTS COVERED BY
THIS WARRANTY. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THAT ABOVE LIMITATIONS AND
EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY
GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATES TO
STATE.
workmanship under normal usage during the warranty period.
Warranty repairs and replacements will be made without
charge for parts or labor. All parts replaced under warranty will
be considered as part of the original product, and any warranty
on the replaced parts will expire coincident with the original
product warranty. If you think your MANTIS HEDGE TRIMMER
is defective in material or workmanship, you must send it,
along with your proof of purchase (sales receipt) to:
Mantis
1028 Street Road
Southampton, PA 18966
You are responsible for pickup and delivery charges; the
product must be returned to us postage paid.
MANTIS assumes no responsibility in the event that the
product was not assembled or used in compliance with any
assembly, care, safety, or operating instructions contained in
the Owner’s Manual or accompanying the product; was not
used with reasonable care or requires replacement or repair due
to accidents or lack of proper maintenance; or was misused,
MANTIS
1028 Street Road
Southampton, PA 18966
(215) 355-9700
Specifications, descriptions, and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice.
Manufactured by:
1028 STREET ROAD, P.O. BOX 38
SOUTHAMPTON, PA 18966
PHONE 215-357-5110 • FAX 215-357-8045
P/N 310706
© 2010 Schiller Grounds Care, Inc. All Rights Reserved.
7/10
Download from Www.Somanuals.com. All Manuals Search And Download.
|