Makita Saw 4101RH User Manual

Tile Cutter  
125 mm (5”)  
MODEL 4101RH  
003504  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
w w w. m a k i t a t o o l s . c o m  
Download from Www.Somanuals.com. All Manuals Search And Download.  
to whether the outlet is properly  
grounded. If the tools should electrically mal-  
function or break down, grounding provides a  
low resistance path to carry electricity away  
from the user.  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enables better control of the tool in  
unexpected situations.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
Tool Use and Care  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked W-A”  
or W. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
tenance performed by unqualified personnel  
could result in a risk of injury.  
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
USE PROPER EXTENSION CORD: Use only three-wire extension cords that have three-  
prong grounding-type plugs and three-pole receptacles that accept the tool's plug. Make  
sure your extension cord is in good condition. Replace or repair damaged or worn cord  
immediately. When using an extension cord, be sure to use one heavy enough to carry the  
current your product will draw. An undersized cord will cause a drop in line voltage resulting  
in loss of power and overheating. Table 1 shows the correct size to use depending on cord  
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the  
gage number, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
GROUNDING INSTRUCTIONS  
This tool should be grounded while in use to protect the operator from electric shock. The  
tool is equipped with a three-conductor cord and three-prong grounding type plug to fit the  
proper grounding type receptacle. The green (or green and yellow) conductor in the cord is  
the grounding wire. Never connect the green (or green and yellow) wire to a live terminal.  
Your unit is for use on 120 volts and has a plug that looks like Fig. A.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
An adapter Fig. Band Cis available for connecting Fig. Atype plugs to two-prong  
receptacles. The green-colored rigid ear, lug, etc., extending from the adapter must be con-  
nected to a permanent ground, such as a properly grounded outlet box.  
Adapter  
Grounding Means  
Cover of Grounded  
Grounding  
Blade  
Outlet Box  
Fig. A  
Fig. B  
Fig. C  
SPECIFIC SAFETY RULES  
USB071-1  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to cutter safety rules. If  
you use this tool unsafely or incorrectly, you can suffer serious  
personal injury.  
1. DANGER! Keep hands away from cutting  
area and wheel. Keep your second hand  
on auxiliary handle or motor housing. If  
both hands are holding the tool, they cannot  
be cut by the wheel.  
down on bench or floor. A coasting wheel  
will cause the tool to walk backwards, cutting  
whatever is in its path. Be aware of the time it  
takes for the wheel to stop after switch is  
released.  
2. Keep your body positioned to either side  
of the wheel, but not in line with the wheel.  
KICKBACK could cause the tool to jump  
backwards. (See Causes and Operator Pre-  
vention of Kickback)  
5. NEVER hold piece being cut in your hands  
or across your leg. It is important to support  
the work properly to minimize body exposure,  
wheel binding, or loss of control.  
6. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a livewire will  
also make exposed metal parts of the tool  
liveand shock the operator.  
3. Do not reach underneath the work. Do not  
attempt to remove cut material when wheel is  
moving.  
CAUTION: Wheels coast after turn off.  
4. Always observe that the wheel has  
stopped spinning before placing tool  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. When ripping always use a rip fence or  
straight edge guide. This improves the  
accuracy of cut and reduces the chance for  
wheel binding.  
BACK may occur. Investigate and take  
corrective actions to eliminate the cause of  
wheel binding.  
When restarting a tool in the workpiece,  
center the wheel in the kerf and check that  
teeth are not engaged into the material. If  
wheel is binding, it may walk up or KICK-  
BACK from the workpiece as the tool is  
restarted.  
Support large panels to minimize the risk  
of wheel pinching and KICKBACK. Large  
panels tend to sag under their own weight.  
Supports must be placed under the panel on  
both sides, near the line of cut and near the  
edge of the panel.  
8. Always use wheels with correct size and  
shape (diamond vs. round) arbor holes.  
Wheels that do not match the mounting hard-  
ware of the tool will run eccentrically, causing  
loss of control.  
9. Never use damaged or incorrect wheel  
washers or bolts. The wheel washers and  
bolt were specially designed for your tool, for  
optimum performance and safety of opera-  
tion.  
To minimize the risk of wheel pinching and  
kickback. When cutting operation requires  
the resting of the tool on the workpiece, the  
tool shall be rested on the larger portion and  
the smaller piece cut off.  
Do not use dull or damaged wheel.  
Unsharpened or improperly set wheels pro-  
duce narrow kerf causing excessive friction,  
wheel binding and KICKBACK.  
Wheel depth and bevel adjusting locking  
levers must be tight and secure before  
making cut. If wheel adjustment shifts while  
cutting, it may cause binding and KICKBACK.  
Use extra caution when making a Pocket  
Cutinto existing walls or other blind  
areas. The protruding wheel may cut objects  
that can cause KICKBACK.  
NEVER place your hand or fingers behind  
the tool. If kickback occurs, the tool could  
easily jump backwards over your hand, lead-  
ing to serious personal injury.  
10. Causes and Operator Prevention of Kick-  
back:  
Kickback is a sudden reaction to a pinched,  
bound, or misaligned wheel, causing an  
uncontrolled tool to lift up and out of the work-  
piece toward the operator.  
When the wheel is pinched or bound tightly  
by the kerf closing down, the wheel stalls and  
the motor reaction drives the unit rapidly back  
toward the operator.  
If the wheel becomes twisted or misaligned in  
the cut, the teeth at the back edge of the  
wheel can dig into the top surface of the  
material being cut causing the wheel to climb  
out of the kerf and jump back toward the  
operator.  
Kickback is the result of tool misuse and/or  
incorrect operating procedures or conditions  
and can be avoided by taking proper precau-  
tions as given below:  
Maintain a firm grip on the tool and posi-  
tion your body and arm to allow you to  
resist KICKBACK forces. KICKBACK forces  
can be controlled by the operator, if proper  
precautions are taken.  
When wheel is binding, or when interrupt-  
ing a cut for any reason, release the trig-  
ger and hold the tool motionless in the  
material until the wheel comes to a com-  
plete stop. Never attempt to remove the  
tool from the work or pull the tool back-  
ward while the wheel is in motion or KICK-  
11. When operating the tool, keep the cord  
away from the cutting area and position it  
so that it will not be caught on the work-  
piece during the cutting operation. Oper-  
ate with proper hand support, proper  
workpiece support, and supply cord rout-  
ing away from the work area.  
WARNING: It is important to support the  
workpiece properly and to hold the tool  
firmly to prevent loss of control which  
could cause personal injury.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
12. Use only diamond wheels. NEVER use  
tool with wood cutting blades or other  
sawblades. Such blades when used on  
this tool frequently kick and cause loss of  
control leading to personal injury.  
serious accidents, because it is extremely  
dangerous.  
19. Do not stop the wheel by lateral pressure  
on the disc.  
20. Some material contains chemicals which  
may be toxic. Take caution to prevent dust  
inhalation and skin contact. Follow mate-  
rial supplier safety data.  
13. Check the wheel carefully for cracks or  
damage  
before  
operation.  
Replace  
cracked or damaged wheel immediately.  
14. Use only flanges specified for this tool.  
21. If the plug or receptacle does get wet, DO  
NOT unplug the cord. Disconnect the fuse  
or circuit breaker that supplies power to  
the tool. Then unplug and examine for  
presence of water in the receptacle.  
15. Be careful not to damage the spindle,  
flanges (especially the installing surface)  
or bolt. Damage to these parts could  
result in wheel breakage.  
16. Make sure the wheel is not contacting the  
workpiece before the switch is turned on.  
Wait until the wheel attains full speed  
before cutting.  
22. WARNING: To reduce the risk of electro-  
cution when using an extension cord,  
keep ALL connections dry and off the  
ground.  
17. Stop operation immediately if you notice  
23. Ground Fault Circuit Interrupter (GFCI)  
protection should be provided on the cir-  
cuit(s) or outlet(s) to be used for the tool.  
Receptacles are available having built-in  
GFCI protection and may be used for this  
measure of safety.  
anything abnormal.  
18. Never attempt to cut with the tool held  
upside down in a vise. This can lead to  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SYMBOLS  
USD101-2  
The followings show the symbols used for tool.  
V .......................volts  
................alternating current  
....................no load speed  
A .......................amperes  
n
˚
Hz .....................hertz  
.../min................revolutions or reciprocation per  
minute  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
003508  
Ground Fault Circuit Interrupter  
R
1
2
T
3
Connect the tool to a power supply and test the Ground Fault  
Circuit Interrupter (GFCI) before using the tool. Push the  
RESET (R) button and confirm that the pilot lamp lights.  
Push the TEST (T) button and confirm that the pilot lamp  
goes out. Push the RESET (R) button again to use the tool.  
WARNING:  
1. RESET (R) Button  
2. Pilot lamp  
Do not use the tool if the pilot lamp does not go out when  
the TEST (T) button is pushed.  
3. TEST (T) Button  
003510  
Adjusting the depth of cut  
Loosen the wing bolt on the depth guide and move the base  
up or down. At the desired depth of cut, secure the base by  
tightening the wing bolt.  
1
2
1. Wing bolt  
2. Base  
003515  
Bevel cutting  
Loosen the wing nut on the bevel scale plate on the front of  
the base. Set for the desired angle (0° - 45° ) by tilting  
accordingly, then tighten the wing nut securely.  
1
1. Wing nut  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
003516  
Loosen the wing bolt on the depth guide and move the base  
so that the end of the blade case is above the red line on the  
depth guide. Then tighten the wing bolt to secure the base.  
1
NOTE:  
If the end of the blade case is under the red line on the  
depth guide, the outer flange may hit the workpiece  
when you perform the bevel cut.  
2
3
1. Wing bolt  
2. End of blade case  
3. Red line  
003520  
Sighting  
1
For straight cuts, align the A position on the front of the base  
with your cutting line. For 45° bevel cuts, align the B position  
with it.  
A
B
2
1. Base  
2. Top guide  
003523  
Switch action  
CAUTION:  
1
2
Before plugging in the tool, always check to see that the  
switch trigger actuates properly and returns to the OFF”  
position when released.  
To prevent the switch trigger from being accidentally pulled, a  
lock-off button is provided.  
To start the tool, depress the lock-off button and pull the  
switch trigger. Release the switch trigger to stop.  
1. Switch trigger  
2. Lock-off button  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
003528  
Installing or removing diamond wheel  
Hold the outer flange with the wrench and loosen the hex  
socket head bolt clockwise with the hex wrench. Then  
remove the hex socket head bolt and outer flange.  
2
1
1. Wrench 22  
2. Hex wrench  
003529  
Install the diamond wheel, outer flange and hex socket head  
bolt onto the spindle. Hold the outer flange with the wrench  
and tighten the hex socket head bolt counterclockwise with  
the hex wrench. BE SURE TO TIGHTEN THE HEX SOCKET  
HEAD BOLT SECURELY.  
1
2
3
4
CAUTION:  
Use only the Makita wrench to install or remove the  
wheel.  
1. Inner flange  
2. Diamond wheel  
3. Outer flange  
4. Hex socket head bolt  
Pressure regulator assembly  
Use the pressure regulator assembly to connect to water  
source. It consists of the following parts.  
Part name  
Description  
Preset at about 15 psi.  
3/4female hose thread (inlet) x 3/4male hose thread (outlet)  
Flow capacity: Maximum 390 GPH, minimum 10 GPH  
Inlet pressures: Maximum 100 psi, minimum 25 psi.  
For connecting 1/4vinyl tube to a faucet  
3/4swivel x 1/4adaptor  
Pressure regulator  
Adaptor  
Vinyl tube  
Water pipe  
1/4in outer diameter x 11/16in inner diameter x 18in length  
For adjusting the amount of water flow  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
003535  
Assemble the above parts hand tight as follows.  
1
2
1. Cut the vinyl tube at an angle for easier insertion. Push  
the end of the vinyl tube into the end of the adaptor using  
a combination pushing and twisting motion.  
3
4
2. Screw the pressure regulator tight on a the adaptor.  
3. Connect the vinyl tube firmly to the water pipe.  
5
1. Pressure regulator assembly  
2. Pressure regulator  
3. Adaptor  
4. Vinyl tube  
5. Water pipe  
003536  
Installing water pipe  
1
First, unplug the tool. Loosen the wing bolt on the depth  
guide and move the base down. Install the water pipe on the  
blade case using the screw.  
2
3
1. Wing bolt  
2. Blade case  
3. Water pipe  
003537  
Screw the pressure regulator tight on a faucet.  
Adjust the amount of water flow by simply adjusting the water  
cock.  
1
2
CAUTION:  
Do not connect the adaptor directly to a faucet. If you do  
so, the vinyl tube may come off the water pipe during  
operation.  
3
4
1. Faucet  
2. Pressure regulator assembly  
3. Water cock  
4. Water pipe  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
003543  
Installing cover (A)  
Install the cover (A) on the tool so that its side with Upside  
mark faces upward.  
1
2
1. Clamp  
2. Cover (A)  
OPERATION  
003545  
Adjust the amount of water flow. Hold the tool firmly. Set the  
base plate on the workpiece to be cut without the wheel mak-  
ing any contact. Then turn the tool on and wait until the  
wheel attains full speed. Now simply move the tool forward  
over the workpiece surface, keeping it flat and advancing  
smoothly until the cutting is completed. Keep your cutting line  
straight and your speed of advance uniform.  
CAUTION:  
THIS TOOL SHOULD ONLY BE USED ON  
HORIZONTAL SURFACES.  
Be sure to move the tool forward in a straight line and  
gently. Forcing and exerting excessive pressure or  
allowing the wheel to bend, pinch or twist in the cut can  
cause overheating of the motor and dangerous kickback  
of the tool.  
Since excessive cutting may cause overload of the  
motor, the depth of cut should not be more than 20 mm  
(13/16) at a pass. When you wish to cut more than  
20 mm (13/16) deep, make a couple of passes with  
progressively deeper settings.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
Dressing diamond wheel  
If the cutting action of the diamond wheel begins to diminish,  
use an old discarded coarse grit bench grinder wheel or con-  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
crete block to dress the diamond wheel. To do this, tightly  
secure the bench grinder wheel or concrete block and cut in  
it.  
After use  
Blow away dust from the inside of the tool by running the tool  
at an idle for a while. Brush off accumulation of dust on the  
base. Accumulation of dust in the motor or on the base may  
cause a malfunction of the tool.  
003543  
Cleaning covers  
When accumulation of dust on the cover (A) looks excessive,  
loosen the clamp and remove the cover (A). Wash off accu-  
mulation of dust inside the cover (A) and wipe it. Then install  
1
the cover (A) on the tool so that its side with Upside  
mark faces upward. Push the cover (A) toward the motor as  
far as it will go and secure it by tightening the clamp.  
2
1. Clamp  
2. Cover (A)  
003549  
When changing the wheel, clean the cover (B) at the same  
time. Loosen the screw securing the cover (B) and remove  
the cover (B). Wash off accumulation of dust inside the cover  
(B) and wipe it. Then attach the cover (B) to the tool by tight-  
ening the screw. Accumulation of dust inside the covers may  
cause a malfunction of the tool.  
1
2
CAUTION:  
1. Cover (B)  
2. Screw  
When using the tool, be sure to attach the covers (A)  
and (B).  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
First, remove the cover (A).  
1. Limit mark  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
003550  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
1
2
1. Brush holder cap  
2. Screwdriver  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Diamond wheels  
Hex wrench 5  
Wrench 22  
Rip fence (guide rule)  
Pressure regulator assembly  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Class  
Postage  
Required  
Post Office will  
not deliver  
without proper  
postage.  
Makita U.S.A., Inc.  
14930 Northam Street  
La Mirada, CA 90638-5753  
Fold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIL THIS PORTION  
Your answers to the following questions are appreciated.  
1.This product was purchased from:  
3. How did you learn about this product:  
Home Center  
Other (  
)
Magazine  
Radio  
Hardware/Lumber Store  
Tool Distributor  
From Dealer  
Newspaper  
Store Display  
Catalog  
Exhibition  
From Friend  
Previous Usage  
Other (  
Industrial Supply  
Construction Supply  
)
2. Use of the product is intended for:  
4. Most favored points are:  
Construction Trade  
Industrial Maintenance  
Home Maintenance  
Hobby  
Design  
Repair Service  
Durability  
Power  
Features  
Size  
Price  
Other (  
)
Other (  
)
Makita Brand  
5. Any comments:  
DATE PURCHASED  
MONTH  
MODEL NO.  
DAY  
YEAR  
SERIAL NO.  
STATUS  
SEX  
Married Single  
M
F
INTL.  
LAST NAME / COMPANY NAME  
STREET ADRESS  
CITY  
AREA  
CODE  
STATE  
ZIP CODE  
PHONE  
40-49  
Under 19  
20-29  
30-39  
50-60  
Over 60  
AGE:  
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.  
Please return this portion by facsimile or mail.  
Facsimile No: (714) 522-8133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
FACTORY SERVICE CENTERS  
1-800-4-MAKITA  
RETAIN THIS PORTION FOR YOUR RECORDS  
ALABAMA  
COLORADO  
KENTUCKY  
NEW MEXICO  
PUERTO RICO  
2365 Pelham Parkway  
Pelham, AL 35124  
(205) 620-1791  
11839 E. 51st Ave.  
Denver, CO 80239-2709  
(303) 371-2850  
1215 S. Hurstbourne Parkway  
Louisville, KY 40222  
(502) 326-3740  
5805 Menaul Blvd. NE  
Albuquerque, NM 87110  
(505) 881-4619  
200 Guayama St.  
Hato Rey, PR 00917  
(787) 250-8776  
ARIZONA  
CONNECTICUT  
508 Spring St.  
Windsor Locks, CT 06096  
(860) 292-6405  
LOUSIANA  
NEWYORK  
TENNESSEE  
3707 E. Broadway Rd., Ste. 6  
Phoenix, AZ 85040  
(602) 437-2850  
5626 Jefferson Hwy.  
Harahan, LA 70123  
(504) 733-4138  
4917 Genessee Street  
Cheektowaga, NY 14225  
(716) 685-9503  
4655 Nolensville Rd.  
Nashville, TN 37211  
(615) 331-9922  
131-35 31st Ave.  
Flushing, NY 11354  
(718) 886-0971  
ARKANSAS  
FLORIDA  
MARYLAND  
TEXAS  
Shackleford Shopping Center  
240 South Shackleford Rd.,  
Ste. C  
620 Douglas Ave. Suite 1302  
Altamonte Springs, FL 32714  
(407) 774-6000  
7541 - 45 Ritchie Highway  
Glen Burnie, MD 21061  
(410) 590-0160  
12801 Stemmons Fwy Ste. 809  
Farmers Branch, TX 75234  
(972) 243-1150  
Little Rock, AR 72211  
(501) 224-5733  
NORTH CAROLINA  
3501-G S. Tryon St.  
Charlotte, NC 28217  
(704) 527-0611  
750 East Sample Road  
Pompano Beach, FL 33064  
(954) 781-6333  
12701 Directors Dr.  
Stafford, TX 77477-3701  
(281) 565-8665  
MASSACHUSETTS  
232 Providence Hwy.  
Westwood, MA 02090  
(617) 461-9754  
CALIFORNIA  
41850 Christy St.  
Fremont, CA 94538-5107  
(510) 657-9881  
Thompson Center Waters  
5501 W. Waters Ave., Ste. 406  
Tampa, FL 33634  
3453 IH-35 North, Ste. 101  
San Antonio, TX 78219  
(210) 228-0676  
OHIO  
6253 E. Main St.  
Columbus, OH 43213  
(614) 860-0222  
(813) 886-8292  
MICHIGAN  
1421 N. Clovis Ave., Ste. 112  
Fresno, CA 93727  
(559) 252-5166  
37454 Ann Arbor Trail  
Livonia, MI 48150  
(313) 432-1012  
UTAH  
GEORGIA  
6379 Pearl Road  
Parma Heights, OH 44130  
(440) 843-7555  
145 E. 1300 S., Ste. 101  
Salt Lake City, UT 84115  
(801) 359-3410  
4680 River Green Parkway  
Duluth, GA 30096-2566  
(770) 476-8911  
14930 Northam St.  
La Mirada, CA 90638-5753  
(714) 522-8088  
MINNESOTA  
6427 Penn Ave. South  
Richfield, MN 55423  
(612) 869-5199  
1617 E. Kemper Rd.  
Sharonville, OH 45246  
(513) 771-0788  
VIRGINIA  
5760 Northampton Blvd,. Ste.  
102  
Virginia Beach, VA 23455  
(757) 460-0280  
1970 Fulton Avenue  
Sacramento, CA 95825  
(916) 482-5197  
HAWAII  
4510 Salt Lake Blvd., Suite A7  
Honolulu, HI 96818  
(808) 847-0038  
MISSOURI  
OKLAHOMA  
1440 South EStreet  
San Bernardino, CA 92408  
(909) 885-1289  
9876 Watson Road  
St. Louis, MO 63126-2221  
(314) 909-9889  
552 E. Memorial Road  
Oklahoma City, OK 73114  
(405) 752-2655  
ILLINOIS  
WASHINGTON  
1450 Feehanville Dr.  
Mt. Prospect, IL 60056-6011  
(847) 297-3100  
22220 84th Ave. So., Bldg. A  
Kent, WA 98032  
(253) 395-8055  
7674 Clairemont Mesa Blvd.  
San Diego, CA 92111  
(858) 278-4471  
NEBRASKA  
OREGON  
4129 S. 84th St.  
Omaha, NE 68127  
(402) 597-2925  
828 19th Avenue., N.W.  
Portland, OR 97209  
(503) 222-1823  
1714 E.McFadden Ave., Unit M  
Santa Ana, CA 92705  
(714) 667-5066  
INDIANA  
WISCONSIN  
8403 Michigan Road, Unit 1  
Indianapolis, IN 46268  
(317) 334-9980  
Lincoln Plaza Shopping Ctr.  
2245 S. 108th St. West Allis, WI  
53227  
NEVADA  
3375 S. Decatur Blvd.  
Suites. 22 - 24  
Las Vegas, NV 89102  
(702) 368-4277  
PENNSYLVANIA  
Springwater Plaza  
364 Wilmington W. Chester  
Pike  
Glen Mills, PA 19342  
(610) 459-4122  
1565 Winchester B.  
Campbell, CA 95008-0501  
(408) 379-0377  
(414) 541-4776  
KANSAS  
8819 W. 95th St.  
Overland Park, KS 66212  
(913) 642-1111  
16735 Saticoy St., Ste. 105  
Van Nuys, CA 91406  
(818) 782-2440  
NEW JERSEY  
6200 Babcock Blvd  
Pittsburgh, PA 15237  
(412) 366-6363  
251 Herrod Blvd.  
Dayton, NJ 08810-1539  
(609) 655-1212  
CUSTOMERS RECORD  
Date Purchased  
When you need service: Send  
complete tool (prepaid) to one  
of the Makita Factory Service  
Centers listed, or to an Authorized  
Makita Service Center. Be sure  
to attach a letter to the outside of  
the carton detailing the problem  
with your tool.  
Dealers Name & Address  
Model No.  
Serial No.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
lead from lead-based paints,  
crystalline silica from bricks and cement and other masonry products, and  
arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of  
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.  
Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of  
Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective  
workmanship or material, Makita will repair (or at our option, replace) without charge.  
This Warranty does not apply where:  
repairs have been made or attempted by others:  
repairs are required because of normal wear and tear:  
the tool has been abused, misused or improperly maintained:  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING  
AND AFTER THE TERM OF THIS WARRANTY.  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF  
"MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE-YEAR TERM OF  
THIS WARRANTY.  
This Warranty gives you specific legal rights, and you may also have other rights which vary form state to state.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
884156D067  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Leica Microscope Magnifier MZ16 F User Manual
LG Electronics Refrigerator E16B User Manual
Lincoln Automobile 2009 MKX User Manual
Lindy Switch CPU Switch Duo User Manual
Linksys Network Router RT41P2 AT User Manual
Louisville Tin and Stove Electric Heater VFM103 User Manual
Mabe Canada Microwave Oven JVM1620 User Manual
Magnavox Flat Panel Television 17MD250V User Manual
Makita Power Hammer BHR240 User Manual
Mellerware Toaster 2 5 2 0 09 0 0 W User Manual