VENT FREE
INFRA RED HEATERS
INSTALLATION AND
OPERATION INSTRUCTIONS
P/N 88900 / REV. 02/04
R
MODEL NUMBERS
NATURAL GAS
PROPANE GAS
MANUAL MODELS
VFM63, VFM103, VFM203, VFM303 VFT101, VFT201, VFT301
VFM64, VFM104, VFM204, VFM304 VFT102, VFT202, VFT302
THERMOSTAT MODELS
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury, or loss of life.
-
Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
-
WHAT TO DO IF YOU SMELL GAS:
•
•
Do not try to light any appliance.
Do not touch any electrical switch; do not use any
phone in your building.
•
•
Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire
department.
INSTALLER: Leave this manual
with the appliance.
CONSUMER: Retain this
manual for future reference.
INSTALLER MUST SHOW
HOMEOWNER PROPER
LIGHTING AND OPERATION
OF HEATER. HAVE THEM
COMPLETE AND RETURN
THE WARRANTY CARD.
-
INSTALLATION AND SERVICE MUST BE
PERFORMED BY A QUALIFIED
INSTALLER, SERVICE AGENCY OR THE
GAS SUPPLIER.
This is an unvented gas fired heater. It uses air (oxygen) from the room in which it is installed. Provisions
for adequate combustion and ventilation air must be provided. See Pg. 4 & 5.
This unit is not approved for installation in greenhouses,or environments involving dusty, wet,
corrosive, or explosive conditions. Such conditions will invalidate the warranty and may create
unsafe conditions.
This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) home,
where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other gases.
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION – CONT’D.
For your protection this heater is equipped with an Oxygen Depletion Sensor (ODS) pilot system. Never operate heater if
ODS has been damaged or tampered with as this could expose you to Carbon Monoxide (a colorless, odorless gas) that
could result in injury or death. Early signs of Carbon Monoxide poisoning resemble influenza, with headaches, dizziness,
or nausea. If you develop these symptoms GET FRESH AIR AT ONCE. Turn off heater and call a qualified serviceman to
check heater. Some people are more affected by Carbon Monoxide than others: Including pregnant women, persons with
a heart or lung disease, anemia, those under the influence of alcohol, and those at high altitudes.
OPERATION
Infrared heaters “heat like the sun” with almost instantaneous, safe, clean burning “waves” of infrared heat. Like the sun,
they must “see” the object to be heated. Make sure they are installed away from furniture or any other object which
might block the infrared “waves”. The Cozy thermostatically controlled units offer the additional benefit of automatically
cycling the heating to maintain just the right room temperature. Ventfree gas room heaters are designed strictly for
“supplemental” room heat use and should never be installed as “sole source heating”.
ROOM HEATER SPECIFICATIONS
Your room heater comes packed in a single carton. Before installation, check the rating plate to verify that the Model
Number is correct and that the room heater is equipped for the type gas you intend to use.
MODELNUMBER
NATURALGAS
PROPANEGAS
TYPE CONTROL
MANUAL MODELS
THERMOSTAT MODELS
VFM63
VFM64
MAN.
VFM103
VFM104
MAN.
VFM203
VFM204
MAN.
VFM303
VFM304
MAN.
VFT101 VFT201
VFT102 VFT202
VFT301
VFT302
T-STAT
BULB
T-STAT
BULB
22-1/2”
14-9/16”
7”
T-STAT
BULB
HEIGHT
22-1/2”
11-1/2”
7”
22-1/2”
14-9/16”
7”
22-1/2”
22-1/2”
26-13/16”
7”
22-1/2”
20-11/16”
7”
22-1/2”
26-13/16”
7”
WIDTH
20-11/16”
7”
DEPTH
INPUT (BTU/HR.)
5,500
10,000
LO / 10,000
HI / 20,000
LO / 10,000
MED./20,000
HI / 30,000
½”
10,000
20,000
30,000
Gas Supply Line Size
Optional CVF Blower
Optional Floor Stand
Bathroom Installation
Bedroom Installation
Piezo Ignitor
½”
½”
½”
½”
½”
½”
NO
NO
YES
YES
NO
YES
NO
YES
YES
NO
YES
YES
NO
NO
YES
NO
YES
YES
NO
YES
YES
YES
16 LB.
NO
YES
YES
22 LB.
NO
NO
YES
YES
22 LB.
NO
NO
YES
30 LB.
YES
YES
30 LB.
YES
35 LB.
Shipping Weight
35 LB.
As applicable:
1. An unvented room hetaer having an input rating of more than 10,000 Btu per hour shall not be installed in a bedroom
or bathroom; or
2. An unvented room heater having an input rating of more than 6,000 Btu per hour shall not be installed in a bathroom.
SAFETY INSTRUCTIONS
1) Keep burner and control compartment clean.
2) Due to high temperatures, the heater should be located out of traffic and away from furniture and draperies.
3) Children and adults should be alerted to the hazard of high surface temperature and should stay away to avoid burns
or clothing ignition.
4) Young children should be carefully supervised then they are in the same room with this heater.
5) Do not place clothing or other flammable material on or near the heater.
6) Any safety screen or guard removed for servicing must be replaced prior to operating the heater.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS - CONTINUED
7) Installation and repair should be done by a qualified service person. The heater should be inspected before use
and at least annually by a professional service person. More frequent cleaning may be required due to excessive
lint from carpeting, bedding, material, etc. It is imperative that control compartments, burners, and circulating air
passageways of the heater be kept clean.
8) “WARNING: Any changes to this heater or its controls can be dangerous”.
9) Do not use this heater if any part has been under water. Immediately call a qualified service person to inspect the
heater and to replace any part of the control system and any gas control which has been under water.
10) Due to high surface and radiated temperatures, keep children, clothing, and furniture away.
11) Do not install this heater in a recreational vehicle.
12) Never use a match, candle, flame or other source of ignition to check for gas leaks. Use only soapy water or
liquid detergent.
13) Before cleaning or servicing, turn off the gas and allow heater to cool.
14) Do not put objects around the heater that will obstruct the flow of combustion and ventilation air.
15) When installing the heater allow adequate accessibility clearances for servicing and proper operation.
16) Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.
17) Do not install in a residential or commercial garage.
18) WARNING: Do not use a blower or other accessory not approved for use with this heater.
19) “WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property
damage.”
20) “WARNING: Do not allow fans to blow directly into the appliance. Avoid any drafts that alter burner flame
patterns.”
21) This appliance is intended for supplemental heating.
FRESH AIR FOR COMBUSTION, VENTILATION AND HEAT DISTRIBUTION
With todays energy efficient homes, it is possible to make your home so air tight that it can result in stale air, dry rot, mold
development and host of other related problems. Gas burning appliances need fresh air for combustion as well as for
good distribution of heated air throughout the home. The following guide provides good general rules for classifying and
properly ventilating most homes.
“The National Fuel Gas Code ANSI Z223.1/NFPA54 defines a confined space as a space whose volume is less than 50
cubic feet per 1,000 Btu per hour (4.8m³ per Kw) of the aggregate input rating of all appliances installed in that space and
an unconfined space as a space whose volume is equal to or greater than 50 cubic feet per 1,000 Btu per hour (4.8m³ per
Kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space
in which the appliance is installed, through openings not furnished with doors, are considered a part of the unconfined
space.”
“This heater shall not be installed in a confined space or unusually tight construction unless provisions for adequate
combustion and ventilation air are made. Use the following example to determine if the heater is being installed in a
confined or unconfined space.”
STEP 1. First find the cubic feet of area to be heated length x width x height. NOTE: Include any adjoining rooms that
cannot be separated by closing a door or that have a air exchange grille that cannot be closed between rooms.
EXAMPLE: Area size 25 ft. x 15 ft. x 7-1/2 ft. = 2,812.5 cubic feet.
STEP 2. Divide area cubic feet by 50. EXAMPLE: 2,812.5 ) 50 = 56.25. Multiply this number by 1,000 for total Btu input
room can support. E XAMPLE: 56.25 x 1,000 = 56,250 Btu.
STEP 3. List all gas burning appliances in this area and total the combined Btu input. EXAMPLE:
Cozy vent free heater……………………..
Gaswaterheater…………………………..
Gas range (all burners & oven on)………..
20,000 Btu
58,000 Btu
28,000 Btu
106,000 Btu
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
FRESH AIR FOR COMBUSTION, VENTILATION AND HEAT DISTRIBUTION - CONT’D.
STEP 4. Compare the total Btu the area can support (from Step 2) to the total Btu in the area the heater will be installed
(from Step 3). If the total from Step 2 is larger this is considered an unconfined space, if Btu total from Step 3 is larger this
is considered a confined space and provisions must be made for additional combustion and ventilation air. EXAMPLE:
Btu area can support is 56,250, total Btu in area is 106,000 – this would be a confined space.
NOTE: A third construction class is one with unusually tight construction, defined as, construction where: (A) Walls
and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of 1 per (6x10-11 Kg
per pa-sec-m²) or less with openings gasketed or sealed, and, (B) Weatherstripping has been added on openable windows
and doors, and , (C) Caulking or sealants are applied to areas such as joints around window and door frames, between
sole plates and floors, between wall ceiling joints, between wall panels, at penetration for plumbing, electrical, and gas
lines, and at other openings.
“WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space, or if the
building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods
described in the National Fuel Gas Code, ANSI Z223.1/NFPA54, Section 5.3 or applicable local codes.” Examples would
be to provide two permanent openings either to an adjoining room, or to the outside. See the National Fuel Gas Code for
details. See Figure 9 & Figure 10 below.
Chimney or gas vent
Chimney or gas vent
Ventilation louvers
(each end of attic)
Opening
Outlet Air
Water
Heater
Furnace
Furnace Water
Heater
Inlet Air
Alternate
air inlet
Opening
Equipment located in confined
spaces; all air from inside the
building. See 5.3.3(a).
Ventilation louvers for
unheated crawl space
Equipment located in confined spaces; all air from
outdoors - inlet air from ventilated crawl space and
outlet air to ventilated attic. See 5.3.3(b).
FIGURE 9
FIGURE 10
INSTALLATION
Installation and service must be performed by a qualified installer, service agency or the gas supplier.
LOCATION
1)
2)
For most efficient performance, locate heater as centrally as possible in the area to be heated.
Do not install heater in a closet, alcove or small hallway where the heater could be isolated from the space to be
heated and adequate combustion air by closing a door.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION - CONTINUED
3)
4)
Protect heater from wind, high traffic areas, and drafts (such as doorways, locations that get direct air from a ceiling
fan, etc.) as this will cause nuisance pilot outage.
All models may be wall mounted. Model No. VFM10, VFT10, VFM20, VFT20, VFM30 & VFT30 may be free
standing by adding optional VF-FSK floor stand kit. These floor mounted units must also have an approved, fire
resistant floor base (available from factory) and must be hard piped.
5)
If optional blower is to be added, locate heater so there is safe access to an electrical outlet.
CLEARANCES
1)
Maintain adequate accessibility clearances for
36”
servicing and proper operation.
2)
Minimum clearances as viewed from front of
heater. 3” clearance below heater shall be
measured from top surface of carpeting, tile,
etc.
3)
If VF-FSK Free Standing Kit is used and the
heater is installed directly on carpeting, tile, or
other combustible material other than wood
8”
8”
flooring, the appliance shall be installed on a
metal or wood panel extending the full width
and depth of the appliance, such as a stove
board.
TOOLS AND ADDITIONAL SUPPLIES
REQUIRED
3”
CLEARANCES
1)
2)
3)
4)
Pipe wrenches (2).
Phillip head screwdriver or screwgun.
Pressure test gauge.
An A.G.A. certified manual shut off valve
with 1/8” NPT pressure tap.
Union connector for type of piping used
(check local codes).
5)
6)
7)
8)
9)
Pipe sealant certified for use with L.P. gas.
Components to assemble a drip leg.
Level.
Drill (if anchors are required).
ROUGH-INGASSUPPLY
1)
2)
Determine location of heater. (See
“Operation”, “Fresh Air”, and “Safety
Instructions” for details.
Install at least a ½” diameter gas supply line.
(Gas supply can enter through bottom or
back of heater). See Figure 1.
1-5/8”
13-1/16”
FIGURE 1
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 1 – first stage pipe sizing
PROPANE GAS
10 PSIG Inlet with a 1 PSIG Pressure Drop
Maximum capacity of pipe or tubing, in thousands of BTU/hr. of L.P. Gas
Size of Pipe
Or Copper
Tubing, Inches
LENGTH OF PIPE OR TUBING, FEET*
10
20
30
40
50
60
70
80
90
100
3/8
558
383
309
265
235
213
196
182
171
161
Copper
½
1387
2360
3993
3339
6982
13153
27004
40461
77924
870
700
599
531
481
443
412
386
365
Tubing 5/8
1622
2475
2295
4799
9040
18560
27809
53556
1303
2205
1843
3854
7259
14904
22331
43008
1115
1887
1577
3298
6213
12756
19113
36809
988
896
824
767
719
679
1149
961
2009
3785
7770
11642
22422
(O.D.)
¾
1672
1398
2923
5507
11306
16939
32623
1515
1267
2649
4989
10244
15348
29559
1394
1165
2437
4590
9424
14120
27194
1297
1084
2267
4270
8767
13136
25299
1217
1017
2127
4007
8226
12325
23737
½
Pipe
Size
¾
1
1-1/4
1-1/2
2
125
150
175
200
225
250
275
300
350
400
3/8
½
142
130
118
111
104
90
89
89
82
76
Copper
323
601
293
269
251
235
222
211
201
185
172
Tubing 5/8
546
502
467
438
414
393
375
345
321
(O.D.)
¾
1018
852
1780
3354
6887
10318
19871
923
843
790
740
700
664
634
584
543
½
772
710
660
619
585
556
530
488
454
Pipe
Size
¾
1613
3039
6240
9349
18005
1484
2796
5741
8601
16564
1381
2601
5340
8002
15410
1296
2441
5011
7508
14459
1224
2305
4733
7092
13658
1162
2190
4495
6735
12971
1109
2089
4289
6426
12375
1020
1922
3945
5911
11385
949
1
1788
3670
5499
10591
1-1/4
1-1/2
2
*Total length of piping from outlet of first stage regulator to inlet of second stage regulator (or to inlet of second stage regulator furthest
away).
Notes:
1) To allow 2 PSIG pressure drop, multiply total gas demand by .707, and use capacities from table.
2) For different first stage pressures, multiply total gas demand by the following factors, and use capacities from table.
First State Pressure PSIG
20
21
Multiply by
.844
.912
Data Calculated per NFPA #54 & 58.
TABLE 4 – Second, Single, or Integral Twin Stage Pipe Sizing
11 Inches Water Column Inlet with a ½ Inch Water Column Drop
Maximum capacity of pipe or tubing in thousands of BTU/hr of LP-Gas
PROPANE GAS
Size of Pipe
Or Copper
LENGTH OF PIPE OR TUBING, FEET*
Tubing, Inches
10
20
30
40
50
60
70
80
90
100
3/8
Copper 1/2
Tubing 5/8
49
34
27
23
20
19
—
—
—
—
110
206
348
536
291
608
1146
2353
3525
6789
76
61
52
46
42
38
36
33
32
141
239
368
200
418
788
1617
2423
4666
114
192
296
161
336
632
1299
1946
3747
97
86
78
71
67
62
59
(O.D.)
3/4
7/8
1/2
3/4
1
164
253
137
287
541
1111
1665
3207
146
224
122
255
480
985
1476
2842
132
203
110
231
435
892
1337
2575
120
185
102
212
400
821
1230
2369
113
174
94
105
161
87
100
154
84
Pipe
Size
198
372
764
1144
2204
185
349
717
1074
2068
175
330
677
1014
1954
1-1/4
1-1/2
2
125
—
150
—
175
—
200
—
225
—
250
—
275
—
300
—
350
—
400
—
3/8
Copper 1/2
Tubing 5/8
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
(O.D.)
3/4
7/8
1/2
3/4
1
1-1/4
1-1/2
2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
74
67
62
58
54
51
48
46
43
40
Pipe
Size
155
292
600
899
1731
141
265
544
815
1569
129
244
500
749
1443
120
227
465
697
1343
113
213
437
654
1260
107
201
412
618
1190
101
191
392
587
1130
97
89
83
182
374
560
1078
167
344
515
992
156
320
479
923
*Total length of piping from outlet of regulator to appliance furthest away.
Data Calculated per NFPA #54 & 58.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING HEATER
WALL MOUNT
(VFM20, VFT20, VFM30, VFT30)
WALL MOUNT (VFM6, VFM10, VFT10)
STEP 1. Remove wall mounting bracket from back of
heater.
STEP 2. Locate two studs.
STEP 3. Attach wall mounting bracket to wall studs with
top at desired height using (2) wood screws provided.
Make sure top of bracket is level. See Figure 4.
STEP 4. Hang top of heater over wall mounting bracket.
STEP 5. Remove bottom front panel.
STEP 1. Remove wall mounting bracket from back of
heater.
STEP 2. Locate wall stud.
STEP 3. Attach wall mounting bracket to wall stud
with top at desired height, using (2) screws provided.
Make sure top of bracket is level. See Figure 2.
STEP 4. Hang top of heater on wall mounting bracket.
STEP 5. Remove bottom front panel.
STEP 6. Secure back of heater to wall, utilizing anchors (if
necessary) or wood screws. See Figure 3.
STEP 6. Secure back of heater to wall, utilizing
anchors (if necessary) or wood screws. See Figure 3.
WALL STUD
WALL
MOUNTING
BRACKET
Wall Stud
Wall Mounting Bracket
FIGURE 4
INSTALLING VF-FSK FLOOR BASE KIT
STEP 1. Remove floor base from carton.
STEP 2. Align screw holes in base to holes in heater
bottom.
FIGURE 2
STEP 3. Make sure that cut-out in top of floor base aligns
with cut-out in bottom of heater and the other cut-out in
bottom of heater and the other cut-out in base if facing
towards back of unit (see illustration below).
STEP 4. Attach floor base to bottom of heater using four
#8 screws (provided).
NOTE: Floor bases are for use on VFM10, VFT10, VFM-
20, VFT-20, VFM30 and VFT30 only. The VFM6 Series has
no base and is not approved for use with one.
HEATER
HOLES FOR MOUNTING BACK OF
HEATER TO WALL
FIGURE 3
Make sure this cut-out
faces back of heater.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS CONNECTION
STEP 1.
NOTE:
Make the gas connection between the manual shut off valve and regulator located inside
heater cabinet. Hold regulator when tightening connection to prevent damage to regulator
and internal tubing. See Figure 5 for completed installation.
All piping and connection must be checked for leaks by the installer. If connections are not
exposed, a pressure test must be run. The appliance and its individual shut off valve must
be disconnected from the gas supply piping system during any pressure testing at pressures
in excess of ½ psig (3.5 kPa). The appliance must be isolated from the gas supply piping
system by closing its individual manual shut off valve during any pressure testing of the gas
supply piping system at test pressures equal to or less than ½ psig (3.5kPa).
Manual
Cut off
Valve
Internal Regulator
Outside Reg.
Supplied
by Gas Co.
(Supplied)
Manual Shut Off
Union
1/8” NPT
Pressure
Plug
Drip
Leg
Drip Leg
1/8” NPT Plug
GAS PIPING WITH VF-FSK KIT
FIGURE 5
FIGURE 5A
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
VFM63, VFM103 - NATURAL GAS
VFM64, VFM104 - L.P. GAS
FOR YOUR SAFETY READ BEFORE LIGHT
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A
FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS OF LIFE.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these
instructions exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle
on the floor.
•
If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don’t try to repair it, call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
WHAT TO DO IF YOU SMELL GAS:
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
•
•
Do not try to light any appliance.
Do not touch any electric switch, do not use any
phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
•
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this
label.
2. Depress gas control knob slightly and turn
clockwise
to “OFF”.
3. Turn off all electric power to the appliance.
7. Turn gas control knob counterclockwise
“PILOT”.
to
Gas
Control
Knob
8. Depress gas control knob and hold in. Immediately
begin alternately pushing and releasing piezo
ignitor button, observing pilot, until pilot is lit.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release the gas
control knob and it will pop back up. Pilot should
remain lit. If pilot goes out, repeat steps 2 thru 7.
• If knob does not pop up when released, STOP and
immediately call your service technician or gas
supplier.
NOTE: Knob can not be turned from “PILOT” to
“OFF” unless knob is depressed slightly. Do not force.
4. Wait five (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
STOP! Follow “B” in the safety information above
on this label. If you don’t smell gas, go to the next
step.
• If the pilot will not stay lit after several tries, turn the
gas control knob to “OFF” and call your service
technician or gas supplier.
9. Turn gas control knob counterclockwise
“ON”.
to
5. Locate pilot in the cut-out below the burner.
6. Locate piezo ignitor button on top of heater.
TO TURN OFF GAS TO APPLIANCE
1.
Depress gas control knob slightly and turn clockwise
to “OFF”.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
VFM203 - NATURAL GAS
VFM204 - L.P. GAS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A
FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PER-
SONAL INJURY OR LOSS OF LIFE.
•
If you cannot reach your gas supplier, call the
fire department.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instruc-
tions exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle
on the floor.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it, call a
qualified service technician. Force or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system and any gas control
which has been under water.
WHAT TO DO IF YOU SMELL GAS:
•
•
Do not try to light any appliance.
Do not touch any electric switch, do not use any
phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
•
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this
label.
2. Depress gas control knob slightly and turn clockwise
to “OFF”.
3. Turn off all electric power to the appliance.
7. Turn gas control knob counterclockwise
“PILOT”.
to
Gas
8. Depress gas control knob and hold in. Immediately
begin alternately pushing and releasing piezo
ignitor button, observing pilot, until pilot is lit.
Continue to hold the control knob in for about
one (1) minute after the pilot is lit. Release the
gas control knob and it will pop back up. Pilot
should remain lit. If pilot goes out, repeat steps
2 thru 7.
Control
Knob
NOTE: Knob can not be turned from “PILOT” to “OFF” unless
knob is depressed slightly. Do not force.
• If knob does not pop up when released, STOP and
immediately call your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your
service technician or gas supplier.
4. Wait five (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
STOP! Follow “B” in the safety information above
on this label. If you don’t smell gas, go to the next
step.
5. Locate pilot in the cut-out below the burner.
6. Locate piezo ignitor button on top of heater.
9. Turn on all electric power to the appliance.
10. Turn gas control knob counterclockwise
desired “LO” or “HI” setting.
to
TO TURN OFF GAS TO APPLIANCE
1.
2.
Depress gas control knob slightly and turn clockwise
to “OFF”.
Turn off all electric power to the appliance if service is to be performed.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
VFM303 - NATURAL GAS
VFM304 - L.P. GAS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR
EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR
LOSS OF LIFE.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instruc-
tions exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle
on the floor.
•
If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, don’t try to repair it, call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
WHAT TO DO IF YOU SMELL GAS:
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
•
•
Do not try to light any appliance.
Do not touch any electric switch, do not use any
phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
•
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this
label.
2. Depress gas control knob slightly and turn
clockwise
to “OFF”.
3. Turn off all electric power to the appliance.
7. Turn gas control knob counterclockwise
“PILOT”.
to
Gas
Control
8. Depress gas control knob and hold in. Immediately
begin alternately pushing and releasing piezo
ignitor button, observing pilot, until pilot is lit.
Continue to hold the control knob in for about one
(1) minute after the pilot is lit. Release the gas
control knob and it will pop back up. Pilot should
remain lit. If pilot goes out, repeat steps 2 thru 7.
• If knob does not pop up when released, STOP and
immediately call your service technician or gas
supplier.
Knob
NOTE: Knob can not be turned from “PILOT” to “OFF”
unless knob is depressed slightly. Do not force.
4. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the safety information
above on this label. If you don’t smell gas, go to
the next step.
• If the pilot will not stay lit after several tries, turn the
gas control knob to “OFF” and call your service
technician or gas supplier.
9. Turn on all electric power to the appliance.
5. Locate pilot in the cut-out below the burner.
6. Locate piezo ignitor button on top of heater.
10. Turn gas control knob counterclockwise
desired temperature setting.
to
TO TURN OFF GAS TO APPLIANCE
1.
2.
Depress gas control knob slightly and turn clockwise
to “OFF”.
Turn off all electric power to the appliance if service is to be performed.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
VFT101, VFT201, VFT301 - NAT. GAS /VFT102, VFT202, VFT302 - L.P.
GAS
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A
FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PER-
SONAL INJURY OR LOSS OF LIFE.
•
If you cannot reach your gas supplier, call the
fire department.
A. This appliance has a pilot which must be lighted by
hand. When lighting the pilot, follow these instruc-
tions exactly.
B. BEFORE LIGHTING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle
on the floor.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will
not push in or turn by hand, don’t try to repair it,
call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been
under water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system and any gas
control which has been under water.
WHAT TO DO IF YOU SMELL GAS:
•
•
Do not try to light any appliance.
Do not touch any electric switch, do not use any
phone in your building.
•
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this
label.
2. Depress gas control knob slightly and turn clockwise
to “OFF”.
3. Turn off all electric power to the appliance.
Gas
Control
Knob
7. Turn gas control knob counterclockwise
“PILOT”.
to
8. Depress gas control knob and hold in.
Immediately begin alternately pushing and
releasing piezo ignitor button, observing pilot,
until pilot is lit. Continue to hold the control
knob in for about one (1) minute after the pilot
is lit. Release the gas control knob and it will
pop back up. Pilot should remain lit. If pilot
goes out, repeat steps 2 thru 7.
NOTE: Knob can not be turned from “PILOT” to “OFF” unless
knob is depressed slightly. Do not force.
4. Wait five (5) minutes to clear out any gas. Then smell
for gas, including near the floor. If you smell gas,
STOP! Follow “B” in the safety information above
on this label. If you don’t smell gas, go to the next
step.
• If knob does not pop up when released, STOP
and immediately call your service technician or
gas supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your
service technician or gas supplier.
5. Locate pilot in the cut-out below the burner.
6. Locate piezo ignitor button on top of heater.
9. Turn on all electric power to the appliance.
10. Turn gas control knob counterclockwise
desired temperature setting.
to
TO TURN OFF GAS TO APPLIANCE
1.
2.
Depress gas control knob slightly and turn clockwise
to “OFF”.
Turn off all electric power to the appliance if service is to be performed.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
PROPER OPERATION
ODS / PILOT FLAME
The pilot pressure has been pre-set at the factory and with proper supply pressure will provide a safe,
reliable ignition source. See Figure 6.
INCORRECT -
LOW PRESSURE
INCORRECT - OXYGEN
LEVEL DROPPING
CORRECT
BURNER FLAME
All orificing and pressure setting was done at the factory and, with proper supply pressure, will provide a safe, efficient
source of heat. However, if any questions about manifold pressure, have a qualified serviceman check with a manometer,
Natural Gas will be 5”, L.P. Gas will be 10” w.c. A proper burner flame (See Figure 7) will produce a reddish-orange flow on
the surface of the ceramic burner plaques. If the burner flame has blue streamers or the flame is floating off the surface of
the plaques, turn heater off and call a qualified service person. Do not operate heater if all plaques are not glowing.
NOTE: There will be approximately ¼” space on the sides and top of the burner that will not glow.
VFM20: When turned to the “LO” setting the two middle plaques will light and glow. When valve is turned to “HI” then
FIGURE 7
CORRECT FLAME
INCORRECT FLAME
all four plaques will be lit.
VFM20 / CORRECT FLAME
“LO”
VFM20 / CORRECT FLAME
“HI”
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
The entire heater should be checked and cleaned by a qualified service person before the start of each
heating season. More frequent cleaning may be required due to excessive lint conditions from carpeting,
bedding material, etc.
CABINET
To clean the cabinet and hearth and jamb assemblies of your heater, turn off and allow to cool, then wipe
with a soft damp cloth. This will remove any dust. Never use metal polish, furniture wax, or any type of
cleaning solution as this could cause odors when the heater is turned back on.
MAIN BURNER
Burners may be cleaned by using a low pressure air hose, or soft brush. Be careful not to damage the
ceramic plaque.
ODS/PILOT
STEP 1.
STEP 2.
STEP 3.
Remove bottom front panel.
Disconnect pilot line from pilot.
Use a low pressure air hose to blow through pilot and through ODS opening in side of pilot.
WARNING: Never insert anything into any of the openings in the pilot as this could damage the Oxygen
Depletion System and expose the homeowner to Carbon Monoxide poisoning.
STEP 3 - PILOT CLEANING
WARNING: After any servicing or cleaning make sure heater is completely re-assembled and check for
gas leaks.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
BLOWER INSTRUCTIONS
INSTALLINGTHEVFBBLOWER
STEP 1. Remove blower assembly from shipping carton.
STEP 2. Insert blower assembly into upper back of heater (See Figure 8).
STEP 3. Secure blower to heater using three #8 screws (provided) through holes pre-punched in heater back.
STEP 4. Locate mounting holes for switchbox (See Figure 8).
STEP 5. Secure switchbox to heater using two #8 screws (provided).
STEP 6. Plug power cord into 115 volt three-prong grounded receptacle.
CAUTION:
Always unplug power cord before servicing or cleaning heater. This appliance is equipped with a three-
prong (grounding) plug for your protection against shock hazard and should be plugged directly into a
properly grounded three-prong receptacle.
Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation after servicing.
Switchbox
Blower Assembly
Blower
Motor
Fan
Switch
FIGURE 8
Black
White
If any of the original wire supplied
with the appliance must be re-
placed, it must be replaced with a
wire of at least a 105/C tempera-
ture rating.
WIRING DIAGRAM / VFB BLOWER
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL MODELS
VENT FREE INFRA-RED HEATER
MANUAL CONTROL
PARTS LIST
NAT. GAS
VFM63
L.P. GAS
VFM64
VFM103
VFM203
VFM303
VFM104
VFM204
VFM304
Prices and specifications subject to change
without notice. All prices are F.O.B. factory.
12
11
Blower
Parts
16
10
13
20
32
33
7
18
30
17
31
19
24
21
2
14
15
22
26
9
5
23
25
6
1
3
VFM63,
VFM64
VFM303, VFM304
VFM203, VFM204
VFM103,
VFM104
“MED.”
3 a, b, c
“LO”
“LO”
3 a, b
3
“HI”
“HI”
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS LIST. TOORDERREPLACEMENTPARTSYOUMUSTGIVEMODELNUMBER, SERIAL
NUMBER, TYPE OF GAS USED, PART DESCRIPTION AND PART NUMBER.
MODEL NUMBERS NATURAL
MODEL NUMBERS PROPANE
VFM63
VFM64
VFM103
VFM104
VFM203
VFM204
VFM303
VFM304
REF. PART
LIST
PART
NO.
88290
LIST
PART
NO.
88291
LIST
PART
LIST
PART DESCRIPTION
Valve, CPMM-21400/17
ODS/Pilot (NAT. GAS)
ODS/Pilot (L.P. GAS)
Manifold
NO.
1
NO.
88290
PRICE
$40.60
$41.90
$36.20
$10.10
N/A
PRICE
$40.60
$41.90
$36.20
$20.10
N/A
PRICE
$42.00
$41.90
$36.20
N/A
NO.
88177
PRICE
$41.30
2
88169
88168
88147
N/A
88169
88168
88148
N/A
88169
88168
N/A
88169
88168
N/A
$41.90
$36.20
N/A
2
3
Manifold “LO”
3a
3b
3c
5
88155
88156
N/A
$18.40
$17.90
N/A
88157
88159
88158
88021
88020
88031
88032
$18.80
$18.80
$18.80
$3.40
Manifold “HI”
N/A
N/A
N/A
N/A
Manifold “MEDIUM”
Burner Orifice (NAT. GAS)
Burner Orifice (L.P. GAS)
Gas Regulator (NAT. GAS)
Gas Regulator (L.P. GAS)
Burner Assembly
N/A
N/A
N/A
N/A
88021
88020
88035
88036
88150
88045
88019
88075
35220
80016
88070
88013
88018
35165
35060
35070
35045
35080
35100
88100
35200
35185
35240
91370
$3.40
$3.40
$17.50
$17.50
$42.20
$2.80
$11.70
$4.00
$7.00
$5.70
$2.80
$4.70
$1.10
$16.90
$13.10
$13.10
$14.90
$10.10
$43.40
$21.40
$2.60
$2.90
$5.00
$2.80
88021
88020
88035
88036
88151
88066
88019
88075
35220
80016
88070
88013
88018
35425
35060
35070
35340
35360
35380
88101
35460
N/A
$3.40
$3.40
$17.50
$17.50
$79.70
$4.20
$11.70
$4.00
$7.00
$5.70
$2.80
$4.70
$1.10
$19.30
$13.10
$13.10
$16.20
$10.70
$46.80
$23.00
$2.90
N/A
88021
88020
88031
88032
$3.40
5
$3.40
$3.40
6
$17.50
$17.50
$17.50
$17.50
6
7
88152 $145.50
88153 $197.40
Gas Supply Tube
Control Rod
9
88066
88019
88008
35960
80016
88070
88013
88018
35925
35060
35070
35870
35860
35880
88105
35940
35185
35240
91371
$4.20
$11.70
$5.90
88049
88019
88010
35960
80016
88070
88013
88018
36425
35060
35070
36340
36360
36380
88104
36440
35185
35480
91380
$4.70
$11.70
$6.60
10
11
12
13
14
Control Knob
Wall Mounting Bracket
Piezo
$8.60
$8.60
$5.70
$5.70
Electrode Wire 30"
$2.80
$2.80
Pilot Tubing Assy.24"Nat.&L.P. 15
$4.70
$4.70
Control Rod Grommet
Casing Back
16
17
18
19
20
21
22
23
24
25
26
$1.10
$1.10
$20.00
$13.10
$13.10
$12.70
$12.40
$51.70
$26.60
$4.00
$25.90
$13.10
$13.10
$21.20
$13.80
$58.30
$33.40
$4.60
Casing Left Side
Casing Right Side
Top Front Panel
Bottom Front Panel
Bezel Assembly
Wire Guard
Heat Shield
Valve Support Bracket
Regulator Support Bracket
Lighting Instruction Assembly
$2.90
$2.90
35480
91370
$4.00
$2.80
$5.00
$4.00
$2.80
$4.50
BLOWER PARTS VF-B
Blower/Motor Assembly
Blower Housing
Fan Switch
30
31
32
33
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
88250
37025
88240
80202
37075
37085
$58.60
$13.00
$5.90
$4.20
$6.10
$7.80
88250
37025
88240
80202
37075
37085
$58.60
$13.00
$5.90
$4.20
$6.10
$7.80
Power Cord
Junction Box
Junction Box Cover
* TWO REQUIRED
Mr. Contractor, we only sell parts through our wholesalers, but the prices listed above are for your convenience.
For prompt parts service, contact the wholesaler from which you purchased your Cozy heater. NOTE: Parts &
MARCH 2005
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
THERMOSTAT MODELS
VENT FREE INFRA-RED HEATER
THERMOSTAT CONTROL
PARTS LIST
NAT. GAS
VFT101
VFT201
VFT302
L.P. GAS
VFT102
VFT202
VFT302
Prices and specifications subject to change
without notice. All prices are F.O.B. factory.
Blower
Parts
12
16
13
20
32
33
7
18
30
17
19
31
24
21
2
14
2
22
5
23
6
9
1
VFT101, VFT102
VFT201, VFT202
VFT301, VFT302
3
Mr. Contractor, we only sell parts through
our wholesalers, but the prices listed are for
your convenience. For prompt parts
service, contact the wholesaler from which
you purchased your Cozy heater. NOTE:
Parts & schematic drawings on current
models are shown at www.cozyheaters.com.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS LIST. TOORDERREPLACEMENTPARTSYOUMUSTGIVEMODELNUMBER, SERIAL
NUMBER, TYPE OF GAS USED, PART DESCRIPTION AND PART NUMBER.
MODEL NUMBERS NATURAL
MODEL NUMBERS PROPANE
VFT101
VFT102
VFT201
VFT202
VFT301
VFT302
REF.
PART
NO.
88179
LIST
PART
NO.
88179
LIST
PART
NO.
LIST
PRICE
$88.10
PART DESCRIPTION
Valve, VT-23100/18
ODS/Pilot (NAT. GAS)
ODS/Pilot (L.P. GAS)
Manifold
NO.
1
PRICE
PRICE
$88.10
$88.10
88179
2
88169
88168
88041
88021
88020
88035
88036
88151
88046
35220
80016
88070
88013
88005
35425
35060
35070
35345
35360
35380
88101
35460
35480
91373
$41.90
$36.20
$22.80
$3.40
88169
88168
88490
88021
88020
88031
88032
88152
88046
35960
80016
88070
88013
88005
35925
35060
35070
35855
35860
35880
88105
35940
35480
91373
$41.90
$36.20
$24.60
$3.40
88169
88168
88491
88021
88020
88031
88032
88153
88046
35960
80016
88070
88013
88005
36425
35060
35070
36355
36360
36380
88104
36440
35480
91373
$41.90
$36.20
$35.30
$3.40
2
3
Burner Orifice (NAT. GAS)
Burner Orifice (L.P. GAS)
Gas Regulator (NAT. GAS)
Gas Regulator (L.P. GAS)
Burner Assembly
5
5
$3.40
$3.40
$3.40
6
$17.50
$17.50
$79.70
$6.10
$17.50
$17.50
$145.50
$6.10
$17.50
$17.50
$197.40
$6.10
6
7
Gas Supply Tube
Wall Mounting Bracket
Piezo
9
12
13
14
$7.00
$8.60
$8.60
$5.70
$5.70
$5.70
Electrode Wire 30"
$2.80
$2.80
$2.80
Pilot Tubing Assy.24"Nat.&L.P. 15
$4.70
$4.70
$4.70
Control Rod Grommet
Casing Back
16
17
18
19
20
21
22
23
24
26
$1.20
$1.20
$1.20
$19.30
$13.10
$13.10
$16.20
$10.70
$46.80
$23.00
$2.90
$20.00
$13.10
$13.10
$18.80
$12.40
$51.70
$26.60
$4.00
$25.90
$13.10
$13.10
$21.10
$13.80
$58.30
$33.40
$4.60
Casing Left Side
Casing Right Side
Top Front Panel
Bottom Front Panel
Bezel Assembly
Wire Guard
Heat Shield
Regulator Support Bracket
Lighting Instruction Assembly
$4.00
$4.00
$4.00
$2.80
$2.80
$2.80
BLOWER PARTS VF-B
Blower/Motor Assembly
Blower Housing
Fan Switch
30
31
32
33
N/A
N/A
N/A
N/A
N/A
N/A
88250
37025
88240
80202
37075
37085
$58.60
$13.00
$5.90
$4.20
$6.10
$7.80
88250
37025
88240
80202
37075
37085
$58.60
$13.00
$5.90
$4.20
$6.10
$7.80
Power Cord
Junction Box
Junction Box Cover
Mr. Contractor, we only sell parts through our wholesalers, but the prices listed above are for your convenience.
For prompt parts service, contact the wholesaler from which you purchased your Cozy heater. NOTE: Parts &
MARCH 2005
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING GUIDE
(for qualified serviceman)
SYMPTOM
POSSIBLE CAUSES
CORRECTIVE ACTION
No spark at ODS1.
Ignitor wire off ODS or Piezo.
2. Ignitor wire shorting out on casing.
3. Defective piezo ignitor.
1. Check and re-attach ignitor wire.
2. Move ignitor wire.
3. Replace Piezo ignitor.
4. Set gap at 3/16”.
4. Wrong gap from electrode.
Spark but no ignition
at ODS
1. No gas to heater.
2. Air in gas line.
3. Blocked ODS orifice.
1. Check and turn on gas.
2. Hold in pilot knob to bleed air from gas line.
3. Blow out ODS with low pressure air hose.
ODS will not remain
lit when control
knob is released
1. Safety interlock system activated.
1. Wait five minutes between re-ignition
attempts.
2. Control knob not held in long
enough.
3. Control knob not in “PILOT”
position.
2. Press in control knob, light ODS and hold
control knob in for one minute.
3. Turn control knob to “OFF” then without
pushing down turn knob counterclockwise
until knob stops turning. Push
knob down completely at this point.
4. Tighten thermocouple into gas valve.
5. Replace thermocouple (hand tighten plus
1/4 turn with wrrench).
4. Thermocouple loose.
5. Defective thermocouple.
6. Defective gas valve.
7. Air in line.
6. Replace gas valve.
7. Bleed all air from gas line.
ODS lights but main
burner does not
1. Control knob not in “ON” position.
2. Burner orifice blocked.
1. Turn control knob to “ON”.
2. Clean burner orifice with low pressure
air hose.
3. Gas supply pressure low.
4. Weak thermocouple.
5. Defective gas valve.
3. Check supply pressure. Call gas supplier.
4. Replace thermocouple.
5. Replace gas valve.
Delayed ignition
1. Low gas supply pressure.
1. Check supply pressure. Call gas supplier.
2. Clean burner orifice with low pressure
air hose.
3. Check and replace regulator if necessary.
4. Make sure ODS is properly mounted to
burner bracket.
2. Burner orifice blocked at ODS.
3. Low manifold pressure.
4. ODS not in correct location.
Flashback
1. Broken or defective plaque.
2. Gas supply pressure low.
1. Discontinue use and replace burner assembly.
2. Check supply pressure. Call gas supplier.
One or more plaques
not glowing
1. Burner orifice blocked.
1. Clean burner orifice with low pressure
air hose.
2. Discontinue use and replace burner assembly.
3. Check supply pressure. Call gas supplier.
2. Broken or defective plaque.
3. Low gas supply pressure.
Heater shuts off during 1. Blocked ODS.
normal operation 2. Low gas supply presure.
1. Clean ODS. See maintenance section.
2. Check supply pressure. Call gas supplier.
3. See “Provisions for adequate combustion
and ventilation air” on Page 3 of
instructions.
3. Not an adequate supply of
combustion and ventilation air.
4. Heater located in drafty area.
4. Re-locate heater.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY BULLETIN ON YOUR GAS CONTROL AND PILOT LIGHT
SYSTEM FOR HEATING EQUIPMENT
WHAT YOU DON’T KNOW CAN HURT YOU.
Your pilot light system has been designed for safe and reliable operation. Although safety mechanisms are
built-in, the potential for hazard exists. This information is intended to help you avoid these hazards.
YOUR GAS CONTROL AND PILOT LIGHT
WHAT TO DO IF YOU SMELL GAS . . .
•
Do not try to light any appliance.
Do not touch any electrical switch; do not use
any phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call the
fire department.
SYSTEM
•
Your gas control and pilot light system has a
safety device whose purpose is to shut-off the
gas supply to the appliance if the pilot light goes
out. If you have trouble lighting the pilot or
keeping it lit, it may mean that this safety
device is warning you that there is a problem
with your system. Inspection and repairs or
replacement must be made by a trained gas
service technician.
•
•
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
CRITICAL SAFETY POINTS TO
REMEMBER . . .
TAMPERING IS DANGEROUS
The pilot safety system may also not work if
you do not follow the lighting instructions
carefully or if you tamper with the gas control
that you use to light the pilot. Tampering with
the gas control, particularly with tools, can
damage the safety mechanism in the control
and can allow gas to leak. This can result in a
fire or explosion causing property damage,
personal injury or death.
•
Your gas has been odorized so that you can
smell it. Always smell around for gas before
lighting your appliance.
•
Sniff for L.P.-gas at floor level. LP-gas is
heavier than air and may temporarily exist at
floor level.
IF YOU SMELL GAS, DON’T LIGHT IT
•
•
If you smell gas, do not attempt to light the
pilot. Do not cause a spark by turning on or
off electrical switches or appliances or by
using the phone. Turn off the gas to the
appliances and call your gas supplier from
another location.
If your gas control has gotten wet as the result
of flooding or other wetting, it must be
replaced immediately by a trained gas service
technician. Water can lead to damage of the
internal safety mechanism in the gas control
and can create a hazardous condition.
IF YOU CAN’T LIGHT IT,
DON’T FIGHT IT!
THIS IS NOT AN ADVERTISEMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
should write directly to the manufacturer, and the
name of an alternative service source will be supplied.
The product safety registration card
(packed inside the appliance) must be completed and
returned to the factory.
The Louisville Tin & Stove Co. warrants to
the original user the accompanying product for the period
specified herein, provided said product is installed,
operated, maintained, serviced, and used according to
the instructions and specifications accompanying the
product. AS OUTLINED IN OUR INSTRUCTIONS,
ANY WARRANTY CONSIDERATIONS ARE
CONTINGENT ON INSTALLATION BY A
QUALIFIED INSTALLER (CONTRACTOR).
SELF-INSTALLATION IS NOT RECOMMENDED
AND MAY INVALIDATE YOUR WARRANTY.
If within a period of one year from the date of
installation of the product, any part supplied by the
manufacturer proves to be defective due to workmanship
or material, it will replace such part, provided parts
have not been subjected to misuse, alteration, neglect, or
accidents. The term of the warranty for the heat
exchanger is covered in Table A below. Any claim not
made within ten (10) days after the expiration of the
warranty period shall be deemed waived by the user.
The manufacturer shall have no liability or be
THIS WARRANTY IS EXPRESSLY IN
LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED (WHETHER WRITTEN OR ORAL).
ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR OF FITNESS FOR A
PARTICULAR PURPOSE IS EXPRESSLY
LIMITED TO THE DURATION OF THE
MANUFACTURER’S EXPRESS, WRITTEN
WARRANTY.
UNDER NO CIRCUMSTANCES SHALL
THE MANUFACTURER BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL
DAMAGES OR EXPENSES ARISING DIRECTLY
OR INDIRECTLY FROM ANY COMPONENT OR
FROM THE USE THEREOF. THE REMEDIES
SET FORTH HEREIN SHALL BE THE
EXCLUSIVE REMEDIES AVAILABLE TO THE
USER AND ARE IN LIEU OF ALL OTHER
REMEDIES.
required to perform any obligation under this warranty
unless, when requested, the user returns, at the user’s
expense, the component or product claimed defective,
to the manufacturer for inspection, to enable the
manufacturer to determine if the claimed defect is covered
by this warranty.
SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO YOU.
No charges for freight, labor or other
expenses incurred in the repair, removal, or
replacement of any product or component claimed to
be defective, will be paid by the manufacturer to the
user, and the manufacturer will not be liable for any
expenses incurred, by the user, in remedying any
defect in the product.
THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY
ALSO HAVE OTHER RIGHTS, WHICH VARY,
FROM STATE TO STATE.
Service under this warranty is the
responsibility of the installer. In the event service
under this warranty is needed, the user of the product
shall request such service directly from the installer.
If the user is unable to locate the installer, the user
TABLE A
Warranty for gas appliance heat exchangers only.
Product
Cozy Gas Fired Floor Furnace
Cozy Gas Fired Wall Furnace
Cozy Gas Fired Vented Console Heater
Cozy Gas Fired Direct Vent Heater
Cozy Gas Fired Counterflow Furnace
Cozy Gas Fired Counterflow Direct Vent Furnace
Cozy Gas Fired Mobile Home Direct Vent Furnace
Cozy Gas Fired Hi-Efficient Direct Vent Wall Furnace
Warranty Period
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
10 Years
LOUISVILLE TIN & STOVE COMPANY
P.O. BOX 2767
-
LOUISVILLE, KENTUCKY 40201-2767
Download from Www.Somanuals.com. All Manuals Search And Download.
|