Makita Power Hammer HR4040C User Manual

Rotary Hammer  
40 mm (1 - 9/16”)  
MODEL HR4040C  
003100  
DOUBLE  
INSULATION  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
w w w. m a k i t a t o o l s . c o m  
Download from Www.Somanuals.com. All Manuals Search And Download.  
change the plug in any way. Double insula-  
tion eliminates the need for the three wire  
grounded power cord and grounded power  
supply system.  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enables better control of the tool in  
unexpected situations.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
Tool Use and Care  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked “W-A”  
or “W”. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or long  
hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
tenance performed by unqualified personnel  
could result in a risk of injury.  
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.  
When using an extension cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of  
power and overheating. Table 1 shows the correct size to use depending on cord length and  
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-  
ber, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
SPECIFIC SAFETY RULES  
USB010-2  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to rotary hammer safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. Hold tools by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a livewire will  
make exposed metal parts of the tool live”  
and shock the operator.  
to high intensity noise can cause hearing  
loss.  
3. Wear a hard hat (safety helmet), safety  
glasses and/or face shield. Ordinary eye  
or sun glasses are NOT safety glasses. It  
is also highly recommended that you wear  
a dust mask and thickly padded gloves.  
2. Wear ear protectors when using the tool  
for extended periods. Prolonged exposure  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Be sure the bit is secured in place before  
operation.  
8. Hold the tool firmly with both hands.  
9. Keep hands away from moving parts.  
5. Under normal operation, the tool is  
designed to produce vibration. The  
screws can come loose easily, causing a  
breakdown or accident. Check tightness  
of screws carefully before operation.  
10. Do not leave the tool running. Operate the  
tool only when hand-held.  
11. Do not point the tool at any one in the area  
when operating. The bit could fly out and  
injure someone seriously.  
6. In cold weather or when the tool has not  
been used for a long time, let the tool  
warm up for a while by operating it under  
no load. This will loosen up the lubrica-  
tion. Without proper warm-up, hammering  
operation is difficult.  
12. Do not touch the bit or parts close to the  
bit immediately after operation; they may  
be extremely hot and could burn your  
skin.  
13. Some material contains chemicals which  
may be toxic. Take caution to prevent dust  
inhalation and skin contact. Follow mate-  
rial supplier safety data.  
7. Always be sure you have a firm footing.  
Be sure no one is below when using the  
tool in high locations.  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
SYMBOLS  
USD202-2  
The followings show the symbols used for tool.  
V .......................volts  
....................no load speed  
n
˚
A .......................amperes  
....................Class II Construction  
Hz .....................hertz  
.../min................revolutions or reciprocation per  
minute  
................alternating current  
................number of blow  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
003112  
Switch action  
CAUTION:  
1
Before plugging in the tool, always check to see that the  
switch trigger actuates properly and returns to the OFF”  
position when released.  
To start the tool, simply pull the switch trigger. Release the  
switch trigger to stop.  
1. Switch trigger  
003119  
Speed change  
The revolutions and blows per minute can be adjusted just by  
turning the adjusting dial. The dial is marked 1 (lowest  
speed) to 6 (full speed).  
1
Refer to the table below for the relationship between the  
number settings on the adjusting dial and the revolutions/  
blows per minute.  
1. Adjusting dial  
Number on adjusting dial  
Revolutions per minute  
Blows per minute  
2,500  
6
5
4
3
2
1
450  
430  
370  
310  
250  
230  
2,350  
2,050  
1,700  
1,400  
1,250  
CAUTION:  
If the tool is operated continuously at low speeds for a  
long time, the motor will get overloaded, resulting in tool  
malfunction.  
The speed adjusting dial can be turned only as far as 6  
and back to 1. Do not force it past 6 or 1, or the speed  
adjusting function may no longer work.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the action mode  
Rotation with hammering  
003130  
1
2
For drilling in concrete, masonry, etc., depress the lock but-  
ton and rotate the change lever so that the pointer points to  
the  
symbol. Use a tungsten-carbide tipped bit.  
3
1. Change lever  
2. Pointer  
3. Lock button  
003135  
Hammering only  
1
2
For chipping, scaling or demolition operations, depress the  
lock button and rotate the change lever so that the pointer  
points to the  
chisel, etc.  
symbol. Use a bull point, cold chisel, scaling  
CAUTION:  
Do not rotate the change lever when the tool is running  
under load. The tool will be damaged.  
1. Pointer  
2. Change lever  
To avoid rapid wear on the mode change mechanism, be  
sure that the change lever is always positively located in  
one of the two action mode positions.  
Torque limiter  
The torque limiter will actuate when a certain torque level is  
reached. The motor will disengage from the output shaft.  
When this happens, the bit will stop turning.  
CAUTION:  
As soon as the torque limiter actuates, switch off the tool  
immediately. This will help prevent premature wear of the  
tool.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
003138  
Indicator lamp  
2
The green power-ON indicator lamp lights up when the tool is  
switched ON. If the indicator lamp is lit but the tool does not  
start, the carbon brushes may be worn out, or the electric cir-  
cuit or the motor may be defective. If the indicator lamp does  
not light up and the tool does not start, the ON/OFF switch or  
the mains cord may be defective.  
1
The red service indicator lamp lights up when the carbon  
brushes are nearly worn out to indicate that the tool needs  
servicing. After approx. 8 hours of use, the motor will auto-  
matically be shut off.  
1. Service indicator lamp (red)  
2. Power-ON indicator lamp (green)  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
003139  
Side handle  
CAUTION:  
Use the side handle only when chipping, scaling or  
demolishing. Do not use it when drilling in concrete,  
masonry, etc. The tool cannot be held properly with this  
side handle when drilling.  
The side handle can be swung 360° on the vertical and  
secured at any desired position. It also secures at eight dif-  
ferent positions back and forth on the horizontal. Just loosen  
the clamp nut to swing the side handle to a desired position.  
Then tighten the clamp nut securely.  
003582  
1
2
1. Side handle  
2. Clamp nut  
003147  
Side grip  
The side grip swings around to either side, allowing easy  
handling of the tool in any position. Loosen the side grip by  
turning it counterclockwise, swing it to the desired position  
and then tighten it by turning clockwise.  
1
1. Side grip  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Bit grease (optional accessory)  
Coat the bit shank head beforehand with a small amount of  
bit grease (about 0.5 -1 g; 0.02 - 0.04 oz.). This chuck lubri-  
cation assures smooth action and longer service life.  
003151  
Installing or removing the bit  
1
Clean the bit shank and apply bit grease before installing the  
bit.  
3
2
4
1. Bit for drilling  
2. Bit shank  
3. Bit grease  
4. Bit for chipping, scaling or demol-  
ishing  
003155  
CAUTION:  
Never use A-type shank bits. They can cause damage to  
the tool.  
37  
27  
38.5  
37  
19  
19  
16ø  
A
B
003156  
Make sure that the  
mark is visible on the top end of the  
tool. If the  
mark is not visible, pull the chuck cover down  
1
until it is visible.  
2
1.  
Mark  
2. Chuck cover  
003162  
For drilling  
1
Insert the bit into the tool. Turn the bit and push it in until it  
engages.  
2
1. Bit  
2. Chuck cover  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
003164  
For chipping, scaling or demolishing  
With the cut in the bit shank aligned with the notch in the tool  
holder cap, insert the bit into the tool holder.  
1
The chuck cover will slide up automatically and cover the  
mark.  
2
After installing, always make sure that the bit is securely held  
in place by trying to pull it out.  
1. Cut in bit shank  
2. Notch in tool holder cap  
003169  
To remove the bit, pull the chuck cover down all the way and  
pull the bit out.  
1
2
1. Bit  
2. Chuck cover  
003173  
Bit angle (when chipping, scaling or demolishing)  
1
The bit can be secured at 12 different angles. To change the  
bit angle, depress the lock button and rotate the change lever  
so that the pointer points to the Osymbol. Turn the bit to  
the desired angle.  
2
3
4
1. Lock button  
2. Change lever  
3. Pointer  
4. Osymbol  
003177  
Depress the lock button and rotate the change lever so that  
the pointer points to the  
symbol. Then make sure that the  
1
bit is securely held in place by turning it slightly.  
2
1. Change lever  
2. Pointer  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
003185  
Depth gauge  
The depth gauge is convenient for drilling holes of uniform  
depth. Insert the depth gauge into the hole in the grip base.  
Adjust the depth gauge to the desired depth and then tighten  
the clamp screw to secure the depth gauge.  
2
1
NOTE:  
The depth gauge cannot be used at the position where  
the depth gauge strikes against the tool body.  
1. Depth gauge  
2. Clamp screw  
OPERATION  
003201  
Hammer drilling operation  
Set the change lever to the  
symbol.  
Position the bit at the desired location for the hole, then pull  
the switch trigger. Do not force the tool. Light pressure gives  
best results. Keep the tool in position and prevent it from slip-  
ping away from the hole.  
Do not apply more pressure when the hole becomes clogged  
with chips or particles. Instead, run the tool at an idle, then  
remove the bit partially from the hole. By repeating this sev-  
eral times, the hole will be cleaned out and normal drilling  
may be resumed.  
CAUTION:  
There is a tremendous and sudden twisting force  
exerted on the tool/bit at the time of hole break-through,  
when the hole becomes clogged with chips and  
particles, or when striking reinforcing rods embedded in  
the concrete. Always use the side grip (auxiliary handle)  
and firmly hold the tool by both side grip and switch  
handle during operations. Failure to do so may result in  
the loss of control of the tool and potentially severe  
injury.  
002449  
Blow-out bulb (optional accessory)  
After drilling the hole, use the blow-out bulb to clean the dust  
out of the hole.  
1
1. Blow-out bulb  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
003207  
Chipping/Scaling/Demolition  
Set the change lever to the  
symbol.  
Hold the tool firmly with both hands. Turn the tool on and  
apply slight pressure on the tool so that the tool will not  
bounce around, uncontrolled. Pressing very hard on the tool  
will not increase the efficiency.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
001146  
Replacing carbon brushes  
When the resin insulating tip inside the carbon brush is  
exposed to contact the commutator, it will automatically shut  
off the motor. When this occurs, both carbon brushes should  
be replaced. Keep the carbon brushes clean and free to slip  
in the holders. Both carbon brushes should be replaced at  
the same time. Use only identical carbon brushes.  
2
3
1
1. Commutator  
2. Insulating tip  
3. Carbon brush  
003226  
Use a screwdriver to remove the brush holder cover.  
1
2
1. Screwdriver  
2. Brush holder cover  
003232  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
1
2
1. Screwdriver  
2. Brush holder cap  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Lubrication  
CAUTION:  
This servicing should be performed by Makita  
Authorized or Factory Service Centers only.  
003237  
This tool requires no hourly or daily lubrication because it  
has a grease-packed lubrication system. It should be relubri-  
cated after every 6 months of operation. Send the complete  
tool to Makita Authorized or Factory Service Center for this  
lubrication service. However, if circumstances require that  
you should lubricate it by yourself, proceed as follows.  
1
Run the tool for several minutes to warm it up. Switch off and  
unplug the tool.  
1. Screws  
Loosen the six screws and remove the handle. Note that the  
top screws are different from other screws.  
003241  
Disconnect the two terminals (white and black) by pulling  
them.  
1
2
3
1. Black  
2. Terminals  
3. White  
003243  
Remove the crank cap using a hex wrench. Rest the tool on  
the table with the bit end pointing upwards. This will allow the  
old grease to collect inside the crank housing.  
1
2
1. Hex wrench  
2. Crank cap  
003247  
Wipe out the old grease inside and replace with a fresh  
grease (60 g; 2 oz). Use only Makita genuine hammer  
grease (optional accessory). Filling with more than the spec-  
ified amount of grease (approx. 60 g; 2 oz) can cause faulty  
hammering action or tool failure. Fill only with the specified  
amount of grease.  
1
Reinstall the crank cap and tighten with the hex wrench.  
1. Hammer grease  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
003249  
Connect the two terminals and reinstall the handle.  
CAUTION:  
1
Do not tighten the crank cap excessively. It is made of  
resin and is subject to breakage.  
3
Be careful not to damage the terminals or lead wires  
especially when wiping out the old grease or installing  
the handle.  
2
1. Terminals  
2. White  
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
3. Black  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory  
or attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Spline shank Carbide-tipped bits  
Bull point  
Cold chisel  
Scaling chisel  
Clay spade  
Grooving chisel  
Rammer  
Bushing tool  
Spline shank to A-Taper adapter  
Spline shank to SDS adapter  
Core bit  
Hammer grease  
Bit grease  
Side handle  
Side grip  
Depth gauge  
Blow-out bulb  
Safety goggles  
Plastic carrying case  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Class  
Postage  
Required  
Post Office will  
not deliver  
without proper  
postage.  
Makita U.S.A., Inc.  
14930 Northam Street  
La Mirada, CA 90638-5753  
Fold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIL THIS PORTION  
Your answers to the following questions are appreciated.  
1.This product was purchased from:  
3. How did you learn about this product:  
Home Center  
Other (  
)
Magazine  
Radio  
Hardware/Lumber Store  
Tool Distributor  
From Dealer  
Newspaper  
Store Display  
Catalog  
Exhibition  
From Friend  
Previous Usage  
Other (  
Industrial Supply  
Construction Supply  
)
2. Use of the product is intended for:  
4. Most favored points are:  
Construction Trade  
Industrial Maintenance  
Home Maintenance  
Hobby  
Design  
Repair Service  
Durability  
Power  
Features  
Size  
Price  
Other (  
)
Other (  
)
Makita Brand  
5. Any comments:  
DATE PURCHASED  
MONTH  
MODEL NO.  
DAY  
YEAR  
SERIAL NO.  
STATUS  
SEX  
Married Single  
M
F
INTL.  
LAST NAME / COMPANY NAME  
STREET ADRESS  
CITY  
AREA  
CODE  
STATE  
ZIP CODE  
PHONE  
40-49  
Under 19  
20-29  
30-39  
50-60  
Over 60  
AGE:  
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.  
Please return this portion by facsimile or mail.  
Facsimile No: (714) 522-8133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
FACTORY SERVICE CENTERS  
1-800-4-MAKITA  
RETAIN THIS PORTION FOR YOUR RECORDS  
ARIZONA  
FLORIDA  
MISSOURI  
PENNSYLVANIA  
1704 Babcock Blvd.  
Pittsburgh, PA 15209  
(412) 822-7370  
3707 E. Broadway Rd., Ste. 6  
Phoenix, AZ 85040  
(602) 437-2850  
750 East Sample Road  
Pompano Beach, FL 33064  
(954) 781-6333  
9876 Watson Road  
St. Louis, MO 63126-2221  
(314) 909-9889  
CALIFORNIA  
GEORGIA  
NEBRASKA  
PUERTO RICO  
41850 Christy St.  
Fremont, CA 94538-5107  
(510) 657-9881  
4680 River Green Parkway NW  
Duluth, GA 30096  
(770) 476-8911  
4129 S. 84th St.  
Omaha, NE 68127  
(402) 597-2925  
200 Guayama St.  
Hato Rey, PR 00917  
(787) 250-8776  
14930 Northam St.  
La Mirada, CA 90638-5753  
(714) 522-8088  
ILLINOIS  
NEVADA  
3375 S. Decatur Blvd.  
Suites. 22 - 24  
Las Vegas, NV 89102  
(702) 368-4277  
TENNESSEE  
1120 Elm Hill P.  
Suile 170 Nashville, TN 372  
(615) 248-3321  
1450 Feehanville Dr.  
Mt. Prospect, IL 60056-6011  
(847) 297-3100  
1970 Fulton Avenue  
Sacramento, CA 95825  
(916) 482-5197  
MARYLAND  
TEXAS  
7674 Clairemont Mesa Blvd.  
San Diego, CA 92111  
(858) 278-4471  
7397 Washington Boulevard,  
Suite 104 Elkridge, MD 21075  
(410) 796-4401  
NEW JERSEY  
12801 Stemmons Fwy Ste. 809  
Farmers Branch, TX 75234  
(972) 243-1150  
251 Herrod Blvd.  
Dayton, NJ 08810-1539  
(609) 655-1212  
16735 Saticoy St., Ste. 105  
Van Nuys, CA 91406  
(818) 782-2440  
12701 Directors Dr.  
Stafford, TX 77477-3701  
(281) 565-8665  
MASSACHUSETTS  
232 Providence Hwy.  
Westwood, MA 02090  
(781) 461-9754  
NEWYORK  
4917 Genessee Street  
Cheektowaga, NY 14225  
(716) 685-9503  
3453 IH-35 North, Ste. 101  
San Antonio, TX 78219  
(210) 228-0676  
COLORADO  
11839 E. 51st Ave.  
Denver, CO 80239-2709  
(303) 371-2850  
MINNESOTA  
6427 Penn Ave. South  
Richfield, MN 55423  
(612) 869-5199  
OREGON  
828 19th Avenue, N.W.  
Portland, OR 97209  
(503) 222-1823  
WISCONSIN  
Lincoln Plaza Shopping Ctr.  
2245 S. 108th St. West Allis, WI  
53227  
(414) 541-4776  
CUSTOMER’S RECORD  
Date Purchased  
When you need service: Send  
complete tool (prepaid) to one  
of the Makita Factory Service  
Centers listed, or to an Authorized  
Makita Service Center. Be sure  
to attach a letter to the outside of  
the carton detailing the problem  
with your tool.  
Dealer’s Name & Address  
Model No.  
Serial No.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
lead from lead-based paints,  
crystalline silica from bricks and cement and other masonry products, and  
arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of  
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.  
Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of  
Makitas Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective  
workmanship or material, Makita will repair (or at our option, replace) without charge.  
This Warranty does not apply where:  
repairs have been made or attempted by others:  
repairs are required because of normal wear and tear:  
the tool has been abused, misused or improperly maintained:  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING  
AND AFTER THE TERM OF THIS WARRANTY.  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS  
WARRANTY.  
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
884254C067  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Kuppersbusch USA Oven EEB 68008 User Manual
KVH Industries Satellite TV System eTrac User Manual
LeapFrog Handheld Game System 39700 User Manual
Liebherr Refrigerator 7082 133 00 User Manual
Life Fitness Exercise Bike 95C User Manual
Magnavox VCR MSC455 User Manual
Manitowoc Ice Ice Maker B1300 User Manual
Marantz GPS Receiver ES7001 User Manual
Marantz Home Theater System XV 5270 User Manual
Marmitek Universal Remote Easycontrol 6 User Manual