Installation instructions
for NoFrost combined refrigerator-freezers
Page 12
GB
7082 133-00
ECN 61 111
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Installation dimensions
The socket must be positioned within the areas marked in grey or
above the installation recess.
The ice maker is fitted in the freezer compartment of the combined
refrigerator-freezer. It must be connected to the mains water sup-
ply to work.
The water shut-off valve must be positioned within the areas
marked in grey.
WARNING!
The water shut-off valve must not sit directly above the
socket!
Thegapbetweenthewatershut-offvalveandthesocket
mustcomplywiththeregulationsofthecountryinwhich
the appliance is used!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the anti-tipping device
WARNING!
Connection to the water supply
Safety instructions and warnings
• Donotconnecttothewatersupplywhilethecombinedrefrigerator-
freezer is connected to the electricity supply.
The supplied anti-tipping bracket must be installed in all
cases. This prevents the appliance from tipping over when
the fully loaded door is opened.
• The connection to the mains water supply may only be
made by trained personnel.
Installation:
• The water quality must comply with the drinking water
1. Mark the centre line of the appliance on the floor.
directives of the country in which the appliance is used.
Align the anti-tipping bracket centre to the centre line.
• The ice maker is designed exclusively to make ice cubes in
quantities required by a household and may only be operated
with water suitable for this purpose.
CAUTION!
• All repairs and work on the ice maker may only be carried out by
Ensure that there are no electric cables or water pipes in the
wallsectiontowhichtheanti-tippingbracketistobesecured.
These could be damaged during installation.
customer service personnel or other trained personnel.
• Themanufacturercannotacceptliabilityfordamagecaused
by a faulty connection to the mains water supply.
2. Secure the anti-tipping bracket to the floor using the 3 screws
(6 mm x 60 mm) included in the accessory pack.
The distance between the leading edge of the body of the unit
and the rear edge of the anti-tipping bracket is 610 mm.
Water pressure
The water pressure must be between 0.15 and 0.6 MPa (1.5 -
Important!
6 bar).
When securing the anti-tipping bracket to a concrete floor,
use suitable plugs!
Important:
If the water filter is inserted in the appliance, the water
pressure must lie between 0.3 and 0.6 MPa (3 - 6 bar).
If the water pressure with the inserted water filter is too low,
this may cause the ice maker to malfunction.
The water supply to the appliance must be through a cold
water pipe that can withstand
the operating pressure and
complies with the hygiene
regulations. For this, use the
stainless steel hose supplied
(length 3 m).
Wall
Installation
1. Place the appliance in front of the installation recess.
2. Apply the cover strips to the left and right side walls of the ap-
pliance.
2.
2.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
3. Insert the bent section of the hose through
the opening at the rear of the appliance.
7. Push the appliance slowly into the recess until the compressor
mounting plate touches the anti-tipping bracket.
WARNING!
Topreventtheappliancefromtippingforwards,thecompres-
sormountingplatemustbetouchingtheanti-tippingbracket!
Wall
Appliance
4. Connect the hose to the solenoid valve
at the front side of the appliance.
Anti-tipping bracket
Compressor mounting
plate
5. Route the mains cable towards the socket.
6. Route the water hose towards the water shut-off valve.
8. Connect the hose to the shut-off tap.
Open the shut-off tap and check the system for leakage.
WARNING!
Important!
Do not connect the appliance to the power supply until the
installation is completed.
After the ice maker has been switched on, the water supply system
must be bled. See the section Bleeding the ice maker in the
operating instructions.
CAUTION!
Lay the mains cable and the water hose in such a way that
they will not be damaged when the appliance is slid into
the installation recess.
5.
6.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Levelling the appliance
Fastening the appliance in the recess
1. Adjust the height of the appliance at the front by twisting the
1
Once in the recess, secure the appliance to the body of the unit
using the securing plates (4 x 16 screws). Then click the covers
supplied into place.
adjustable feet
(A/F 27).
Caution!
The front feet of the appliance must be firmly placed on the
floor.
2. Adjusttheheightoftheappliance
attherearbyturningtheadjusting
2
bars
(A/F 5).
Turn the adjusting bars clock-
wiseuntilthecompressormount-
ingplatetouchestheanti-tipping
bracket.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Before fitting the door panels
Panel dimensions
Min. panel thickness = 16 mm
Max. panel thickness = 19 mm
1
Remove the cover
and unscrew the top and bottom attach-
2
ment brackets
from the refrigerator door. These attachment
brackets will be mounted onto the refrigerator door panel.
Maximum panel weight
Refrigerator panel = 27 kg
Important!
Freezer drawer panel = 10 kg
The securing nuts are needed for re-mounting the pre-
assembled door panel onto the refrigerator door.
Unscrewtheattachmentbracketsfromthefreezerdrawers.These
attachment brackets will be mounted onto the freezer panels.
Important!
The screws are needed for re-mounting the pre-assembled
freezer panels onto the freezer drawers.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the attachment brackets onto the door panels
1. Draw a line 1041 mm from the bottom side of the door panel.
2. Draw a further line 107.5 mm from the bottom side of the door panel.
3. Align one of the refrigerator door attachment brackets to the top line, as shown in the illustration below, and secure with at least 6
4 x 14 screws.
4. Align the second refrigerator door attachment bracket to the bottom line, as shown in the illustration below, and secure with at least
6 4 x 14 screws.
5. Secure each of the attachment brackets that have been removed from the freezer drawers using 3 4 x 14 screws, as shown in the
illustration below.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Mounting the refrigerator panel
1. Screw in the adjusting pins on the underside of the refrigerator
4. Close the refrigerator door and check the height of the panel.
door completely (fig. A).
5. Adjust the height of the panel if necessary. Undo the securing
nuts and use the adjusting pins to adjust (fig. C).
fig. C
fig. A
6. Adjust the panel horizontally (using the long slots in the attach-
ment bracket) (fig. D).
7. Tighten the securing nuts.
2. Open the refrigerator door and suspend the refrigerator panel
on the top adjusting pins (fig. B).
3. Screwsecuringnutsontotheadjustingpinsandslightlytighten
(fig. B).
fig. B
fig. D
19
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Undo the three screws on the top of the attachment bracket,
adjust the door panel as displayed in fig. G and then retighten
the screws. The same procedure can be carried out for the
bottom attachment bracket.
8. Remove the adjusting pins (bottom of the refrigerator door)
until these touch the attachment bracket (fig. E).
fig. E
fig. G
9. Screw on the securing nuts and tighten (fig. F).
11. Click the top and bottom covers into place (fig. H).
fig. F
fig. H
20
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Mounting the dust filter
Mounting the freezer panels
Thesupplieddustfilterpreventsthatdirtentersthemotorcompart-
ment, reducing the refrigeration performance. Therefore always
install the dust filter.
1. Pulloutthetopfreezerdrawerandscrewonthepre-assembled
panel. The same screws must be used as those used to screw
on the attachment brackets (3.5 x 13).
1. Pull the bottom freezer drawer right out.
2. Close the freezer drawer and check the position of the panel.
Adjust the height of the panel by undoing the left and right
screws. Tighten the screws.
2. Remove the protective film from the dust filter. Insert the filter at
the bottom, press the button down and click the filter into place.
3. Pull out the bottom freezer drawer and mount the panel in the
same way.
4. For both drawers, cover the gap between the drawer and the
panel with the cover strips supplied. Remove the protective
film from the trim and insert into the gap at the top.
Mounting the ventilation grille
Important!
To ensure fault-free operation of the appliance, you must
install the supplied ventilation grille.
Donotobstructtheventilationopeningorcoveritwithapanel!
3.5 x 13 mm
Changing over door hinges
Door hinges should only be changed by a trained expert.
WARNING!
Do not try to change over the door hinges yourself. The
refrigerator door hinges are fitted with strong closing
springs. If the hinge accidentally snaps shut, this can lead
to serious injury.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|