INSTRUCTION MANUAL
Rotary Hammer /
Combination Hammer
HR2300
HR2310T
HR2600
HR2601
HR2610
HR2610T
HR2611F
HR2611FT
010712
DOUBLE INSULATION
IMPORTANT: Read Before Using.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
Do not expose power tools to rain or wet
conditions. Water entering power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
Power tool use and care
a
18. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
19. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
20. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
8.
9.
21. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
22. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
10. Use of power supply via a RCD with a rated
residual current of 30mA or less is always
recommended.
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication.
A
moment of inattention while
operating power tools may result in serious
personal injury.
12. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
13. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
Service
25. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
26. Follow instruction for lubricating and
changing accessories.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
17. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
27. Keep handles dry, clean and free from oil and
grease.
GEB007-7
ROTARY HAMMER SAFETY
WARNINGS
1.
2.
3.
Wear ear protectors. Exposure to noise can
cause hearing loss.
Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
3
Download from Www.Somanuals.com. All Manuals Search And Download.
wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
FUNCTIONAL DESCRIPTION
CAUTION:
4.
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun
glasses are NOT safety glasses. It is also
highly recommended that you wear a dust
mask and thickly padded gloves.
•
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on
the tool.
Switch action
5.
6.
Be sure the bit is secured in place before
operation.
1. Switch trigger
2. Lock button
Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
1
2
7.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
010720
•
CAUTION:
Before plugging in the tool, always check to see
that the switch trigger actuates properly and returns
to the "OFF" position when released.
8.
9.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop. For continuous
operation, pull the switch trigger, push in the lock button
and then release the switch trigger. To stop the tool from
the locked position, pull the switch trigger fully, then
release it.
Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
only when hand-held.
12. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
Lighting up the lamps
13. Do not touch the bit or parts close to the bit
immediately after operation; they may be
extremely hot and could burn your skin.
14. Some material contains chemicals which may
be toxic. Take caution to prevent dust
inhalation and skin contact. Follow material
supplier safety data.
For Models HR2611F, HR2611FT
1. Lamp
1
SAVE THESE INSTRUCTIONS.
010721
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
CAUTION:
•
Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger to
turn it off.
NOTE:
•
Use a dry cloth to wipe the dirt off the lens of lamp.
Be careful not to scratch the lens of lamp, or it may
lower the illumination.
•
Do not use thinner or gasoline to clean the lamp.
Such solvents may damage it.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the quick change drill chuck
1. Spindle
Reversing switch action
1. Reversing switch
lever
2. Quick change
drill chuck
1
B
2
3. Change cover
line
A
4. Change cover
4
1
3
011562
010722
Check the line of the quick change drill chuck shows the
symbol. Grasp the change cover of the quick change
CAUTION:
•
•
Always check the direction of rotation before
operation.
drill chuck and set the line to the
symbol.
Place the quick change drill chuck on the spindle of the
tool.
Grasp the change cover of the quick change drill chuck
Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.
If the switch trigger can not be depressed, check to
see that the reversing switch is fully set to
and turn the change cover line to the
click can clearly be heard.
symbol until a
•
Selecting the action mode
For Models HR2300, HR2600, HR2601
position
(A side) or (B side).
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the position
(A side) for clockwise rotation or the position (B side)
for counterclockwise rotation.
1
1. Rotation with
hammering
2. Rotation only
3. Action mode
changing knob
Changing the quick change chuck for
SDS-plus
For Models HR2310T, HR2610T, HR2611FT
The quick change chuck for SDS-plus can be easily
exchanged for the quick change drill chuck.
Removing the quick change chuck for SDS-plus
2
3
010723
This tool employs an action mode changing knob. Select
one of the two modes suitable for your work needs by
using this knob.
For rotation only, turn the knob so that the arrow on the
knob points toward the symbol on the tool body.
For rotation with hammering, turn the knob so that the
arrow on the knob points toward the symbol on the tool
body.
1. Quick change
chuck for
SDS-plus
2. Change cover
line
1
3. Change cover
3
2
011561
CAUTION:
•
•
Always set the knob fully to your desired mode
symbol. If you operate the tool with the knob
positioned halfway between the mode symbols, the
tool may be damaged.
Use the knob after the tool comes to a complete
stop.
CAUTION:
•
Before removing the quick change chuck for
SDS-plus, always remove the bit.
Grasp the change cover of the quick change chuck for
SDS-plus and turn in the direction of the arrow until the
change cover line moves from the
symbol to the
symbol. Pull forcefully in the direction of the arrow.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
For Models HR2310T, HR2610, HR2610T, HR2611F,
HR2611FT
Rotation with hammering
may no longer move in the
this time, turn the tool on or turn the chuck by hand
in the symbol position and then rotate the
symbol position. At
action mode changing knob. Forcing the action
mode changing knob may cause tool damage.
1
1. Rotation with
hammering
2. Action mode
changing knob
Torque limiter
The torque limiter will actuate when a certain torque level
is reached. The motor will disengage from the output
shaft. When this happens, the bit will stop turning.
CAUTION:
2
•
•
As soon as the torque limiter actuates, switch off
the tool immediately. This will help prevent
premature wear of the tool.
Bits such as hole saw, which tend to pinch or catch
easily in the hole, are not appropriate for this tool.
This is because they will cause the torque limiter to
actuate too frequently.
010724
For drilling in concrete, masonry, etc., rotate the action
mode changing knob to the
tungsten-carbide tipped bit.
Rotation only
symbol. Use
a
1. Rotation only
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
1
Side grip (auxiliary handle)
010726
For drilling in wood, metal or plastic materials, rotate the
1. Protrusions
2. Grooves
1
action mode changing knob to the
twist drill bit or wood bit.
Hammering only
symbol. Use a
1. Hammering only
2
010713
CAUTION:
•
Always use the side grip to ensure operating safety.
Install the side grip so that the protrusions on the grip fit
in between the grooves on the tool barrel. Then tighten
the grip by turning clockwise at the desired position. It
may be swung 360° so as to be secured at any position.
1
010725
For chipping, scaling or demolition operations, rotate the
action mode changing knob to the
point, cold chisel, scaling chisel, etc.
symbol. Use a bull
Bit grease
Coat the bit shank head beforehand with a small amount
CAUTION:
of bit grease (about 0.5 - 1 g).
•
•
Do not rotate the action mode changing knob when
the tool is running under load. The tool will be
damaged.
To avoid rapid wear on the mode change
mechanism, be sure that the action mode changing
knob is always positively located in one of the three
action mode positions.
This chuck lubrication assures smooth action and longer
service life.
•
When changing from the
symbol mode to the
symbol mode, the action mode changing knob
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The bit can be secured at the desired angle. To change
the bit angle, rotate the action mode changing knob to
the O symbol. Turn the bit to the desired angle.
Rotate the action mode changing knob to the symbol.
Then make sure that the bit is securely held in place by
turning it slightly.
Installing or removing the bit
1. Bit shank
2. Bit grease
2
1
003150
Clean the bit shank and apply bit grease before installing
the bit.
1. Bit
010728
Depth gauge
The depth gauge is convenient for drilling holes of
1
uniform depth.
1. Grip base
2. Lock button
3. Depth gauge
1
2
010714
Insert the bit into the tool. Turn the bit and push it in until it
engages.
3
After installing, always make sure that the bit is securely
held in place by trying to pull it out.
To remove the bit, pull the chuck cover down all the way
and pull the bit out.
010716
Press the lock button on the grip base in the direction of
arrow shown in the figure and with the lock button being
pressed insert the depth gauge into the hex. hole in the
grip base
1. Bit
2. Chuck cover
1
2
1. Toothed side of
hex hole
1
marking on the
grip base
2. Toothed side of
2
010715
the depth gauge
Bit angle (when chipping, scaling or
demolishing)
For Models HR2310T, HR2610, HR2610T, HR2611F,
HR2611FT
010717
At this time, the depth gauge needs to be inserted so that
its toothed side is directed to the toothed side of hex hole
marking on the grip base as shown in the figure.
1. Action mode
changing knob
1
010727
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing or removing the dust cup
1. Lock button
1
1.
2. Grooves
3. Dust cup
symbol
1
2
010718
3
011506
Adjust the depth gauge to the desired depth by moving it
back and forth while pressing the lock button. After the
adjustment, release the lock button to lock the depth
gauge.
Before installing the dust cup, remove the bit from the
tool if installed on the tool. Install the dust cup
(accessory) on the tool so that the
symbol on the
dust cup is aligned with the grooves in the tool.
1. Toothed side of
hex hole
2
1. Bit
2. Chuck cover
1
marking on the
grip base
2. Toothed side of
the depth gauge
1
2
010719
010733
NOTE:
To remove the dust cup, pull the chuck cover in the
direction as shown in the figure and with the chuck cover
pulled take the bit out of the tool.
•
Inserting the depth gauge with its toothed side not
directed to the toothed side of hex hole marking on
the grip base as shown in the figure does not allow
the depth gauge to be locked.
1. Attachment at
1
the foot of dust
cup
Dust cup
1. Dust cup
1
010734
And then grab the attachment at the foot of dust cup and
take it out.
010731
Use the dust cup to prevent dust from falling over the tool
and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in the
figure. The size of bits which the dust cup can be
attached to is as follows.
1. Bellows
2. Attachment
1
Bit diameter
Dust cup 5
Dust cup 9
6 mm - 14.5 mm
12 mm - 16 mm
2
011507
006406
There is another type of dust cup (accessory) which
helps you prevent dust from falling over the tool and on
yourself when performing overhead drilling operations.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Inside periphery
2. Carved side
3. Attachment
4. Cap
OPERATION
1
Always use the side grip (auxiliary handle) and firmly
hold the tool by both side grip and switch handle during
operations.
5. Groove
Hammer drilling operation
3
2
4
5
012895
1. Cap
2. Attachment
1
010729
Set the action mode changing knob to the
symbol.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position and
prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at an
idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
2
012896
NOTE:
•
When installing or removing the dust cup, the cap
may come off the dust cup. At that time, proceed as
follows. Remove the bellows from the attachment
and fit the cap from the side shown in the figure with
its carved side facing upward so that the groove in
the cap fits in the inside periphery of the attachment.
Finally, mount the bellows that has been removed.
Set the action mode changing knob to the
symbol.
CAUTION:
•
There is a tremendous and sudden twisting force
exerted on the tool/bit at the time of hole
break-through, when the hole becomes clogged
with chips and particles, or when striking reinforcing
rods embedded in the concrete. Always use the
side grip (auxiliary handle) and firmly hold the tool
by both side grip and switch handle during
operations. Failure to do so may result in the loss of
control of the tool and potentially severe injury.
011505
NOTE:
If you connect a vacuum cleaner to your hammer,
NOTE:
•
Eccentricity in the bit rotation may occur while operating
the tool with no load. The tool automatically centers itself
during operation. This does not affect the drilling
precision.
cleaner operations can be performed. Dust cap
needs to be removed from the dust cup before the
connection.
Blow-out bulb (optional accessory)
1. Blow-out bulb
1
002449
9
Download from Www.Somanuals.com. All Manuals Search And Download.
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
1. Spindle
2. Quick change
drill chuck
3. Change cover
line
1
2
Chipping/Scaling/Demolition
For Models HR2310T, HR2610, HR2610T, HR2611F,
HR2611FT
4. Change cover
4
3
011562
Use the quick change drill chuck as standard equipment.
When installing it, refer to "changing the quick change
chuck for SDS-plus " described on the previous page.
1. Sleeve
2. Ring
1
011564
Set the action mode changing knob to the
symbol.
3. Quick change
drill chuck
Hold the tool firmly with both hands. Turn the tool on and
apply slight pressure on the tool so that the tool will not
bounce around, uncontrolled. Pressing very hard on the
tool will not increase the efficiency.
3
2
Drilling in wood or metal
For Models HR2300, HR2600, HR2601, HR2610,
HR2611F
011563
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as it
will go. Hold the ring firmly and turn the sleeve clockwise
to tighten the chuck. To remove the bit, hold the ring and
turn the sleeve counterclockwise.
1. Chuck adapter
2. Keyless drill
chuck
1
Set the action mode changing knob to the
symbol.
You can drill up to 13 mm diameter in metal and up to 32
mm diameter in wood.
2
CAUTION:
•
•
Never use "rotation with hammering" when the
quick change drill chuck is installed on the tool. The
quick change drill chuck may be damaged.
Also, the drill chuck will come off when reversing
the tool.
Pressing excessively on the tool will not speed up
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
There is a tremendous twisting force exerted on the
tool/bit at the time of hole breakthrough. Hold the
tool firmly and exert care when the bit begins to
break through the workpiece.
A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you
do not hold it firmly.
011560
Use the optional drill chuck assembly. When installing it,
refer to "Installing or removing the bit" described on the
previous page.
For Models HR2310T, HR2610T, HR2611FT
1. Quick change
chuck for
SDS-plus
2. Change cover
line
1
•
•
•
3. Change cover
3
2
011561
Always secure small workpieces in a vise or similar
hold-down device.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Diamond core drilling
When performing diamond core drilling operations,
OPTIONAL ACCESSORIES
always set the change lever to the
"rotation only" action.
position to use
CAUTION:
•
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
CAUTION:
•
If performing diamond core drilling operations using
"rotation with hammering" action, the diamond core
bit may be damaged.
Operation when using the dust cup
(accessory)
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SDS-Plus Carbide-tipped bits
Core bit
Bull point
Diamond core bit
Cold chisel
Scaling chisel
Grooving chisel
Drill chuck assembly
Drill chuck S13
Chuck adapter
Chuck key S13
Bit grease
Side grip
Depth gauge
Blow-out bulb
Dust cup
Dust extractor attachment
Safety goggles
Plastic carrying case
Keyless drill chuck
1. Dust cap
1
010736
Operate the tool with the dust cup against the ceiling
surface.
NOTE:
•
The dust cup (accessory) is intended only for
drilling in the ceramic workpiece such as concrete
and mortar. Do not use the tool with the dust cup
when drilling in metal or similar. Using the dust cup
for drilling in the metal may damage the dust cup
due to the heat produced by small metal dust or
similar.
•
•
Empty the dust cup before removing a drill bit.
When using the dust cup, make sure that the dust
cap is mounted on it securely.
NOTE:
Some items in the list may be included in the tool
•
package as standard accessories. They may differ
from country to country.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
•
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Makita Corporation
884939A3
Download from Www.Somanuals.com. All Manuals Search And Download.
|