Makita Impact Driver 6952 User Manual

Impact Driver  
MODEL 6952  
004352  
DOUBLE  
INSULATION  
I N S T R U C T I O N M A N U A L  
WARNING:  
For your personal safety, READ and UNDERSTAND before using.  
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
w w w. m a k i t a t o o l s . c o m  
Download from Www.Somanuals.com. All Manuals Search And Download.  
still does not fit, contact a qualified elec-  
trician to install a polarized outlet. Do not  
change the plug in any way. Double insula-  
13. Do not overreach. Keep proper footing  
and balance at all times. Proper footing and  
balance enables better control of the tool in  
unexpected situations.  
tion  
eliminates the need for the three wire  
grounded power cord and grounded power  
supply system.  
14. Use safety equipment. Always wear eye  
protection. Dust mask, non-skid safety  
shoes, hard hat, or hearing protection must  
be used for appropriate conditions. Ordinary  
eye or sun glasses are NOT eye protection.  
5. Avoid body contact with grounded sur-  
faces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of  
electric shock if your body is grounded.  
Tool Use and Care  
6. Do not expose power tools to rain or wet  
conditions. Water entering a power tool will  
increase the risk of electric shock.  
15. Use clamps or other practical way to  
secure and support the workpiece to a  
stable platform. Holding the work by hand or  
against your body is unstable and may lead  
to loss of control.  
7. Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
16. Do not force tool. Use the correct tool for  
your application. The correct tool will do the  
job better and safer at the rate for which it is  
designed.  
8. When operating a power tool outside, use  
an outdoor extension cord marked “W-A”  
or “W”. These cords are rated for outdoor  
use and reduce the risk of electric shock.  
17. Do not use tool if switch does not turn it  
on or off. Any tool that cannot be controlled  
with the switch is dangerous and must be  
repaired.  
Personal Safety  
18. Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
9. Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
19. Store idle tools out of reach of children  
and other untrained persons. Tools are  
dangerous in the hands of untrained users.  
10. Dress properly. Do not wear loose cloth-  
ing or jewelry. Contain long hair. Keep  
your hair, clothing, and gloves away from  
moving parts. Loose clothes, jewelry, or  
long hair can be caught in moving parts.  
20. Maintain tools with care. Keep cutting  
tools sharp and clean. Properly maintained  
tools with sharp cutting edges are less likely  
to bind and are easier to control.  
21. Check for misalignment or binding of  
moving parts, breakage of parts, and any  
other condition that may affect the tools  
operation. If damaged, have the tool ser-  
viced before using. Many accidents are  
caused by poorly maintained tools.  
11. Avoid accidental starting. Be sure switch  
is off before plugging in. Carrying tools with  
your finger on the switch or plugging in tools  
that have the switch on invites accidents.  
12. Remove adjusting keys or wrenches  
before turning the tool on. A wrench or a  
key that is left attached to a rotating part of  
the tool may result in personal injury.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
22. Use only accessories that are recom-  
mended by the manufacturer for your  
model. Accessories that may be suitable for  
one tool, may become hazardous when used  
on another tool.  
tenance performed by unqualified personnel  
could result in a risk of injury.  
24. When servicing a tool, use only identical  
replacement parts. Follow instructions in  
the Maintenance section of this manual.  
Use of unauthorized parts or failure to follow  
Maintenance instructions may create a risk of  
electric shock or injury.  
SERVICE  
23. Tool service must be performed only by  
qualified repair personnel. Service or main-  
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition.  
When using an extension cord, be sure to use one heavy enough to carry the current your  
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of  
power and overheating. Table 1 shows the correct size to use depending on cord length and  
nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage num-  
ber, the heavier the cord.  
Table 1: Minimum gage for cord  
Volts  
120 V  
Total length of cord in feet  
Ampere Rating  
25 ft.  
50 ft.  
100 ft.  
150 ft.  
More Than  
Not More Than  
AWG  
0
6
10  
12  
6
18  
18  
16  
14  
16  
16  
16  
12  
16  
14  
14  
14  
12  
12  
10  
12  
16  
Not Recommended  
SPECIFIC SAFETY RULES  
USB057-2  
DO NOT let comfort or familiarity with product (gained from  
repeated use) replace strict adherence to impact driver safety  
rules. If you use this tool unsafely or incorrectly, you can suffer  
serious personal injury.  
1. Hold tool by insulated gripping surfaces  
when performing an operation where the  
cutting tool may contact hidden wiring or  
its own cord. Contact with a ivewire will  
make exposed metal parts of tool liveand  
shock the operator.  
3. Hold the tool firmly.  
4. Always be sure you have a firm footing.  
Be sure no one is below when using the  
tool in high locations.  
2. Hearing protection should be worn when  
operating in impact conditions.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAVE THESE INSTRUCTIONS  
WARNING:  
MISUSE or failure to follow the safety rules stated in this  
instruction manual may cause serious personal injury.  
SYMBOLS  
USD202-2  
The followings show the symbols used for tool.  
V .......................volts  
....................no load speed  
n
˚
A .......................amperes  
....................Class II Construction  
Hz .....................hertz  
.../min................revolutions or reciprocation per  
minute  
................alternating current  
................number of blow  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FUNCTIONAL  
DESCRIPTION  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before adjusting or checking function on the  
tool.  
004353  
Switch action  
CAUTION:  
Before plugging in the tool, always check to see that the  
switch trigger actuates properly and returns to the OFF”  
position when released.  
1
To start the tool, simply pull the switch trigger. Tool speed is  
increased by increasing pressure on the switch trigger.  
Release the switch trigger to stop.  
1. Switch trigger  
Electric brake  
This tool is equipped with an electric brake. If the tool consis-  
tently fails to quickly stop after switch trigger release, have  
tool serviced at a Makita service center.  
004354  
Reversing switch action  
This tool has a reversing switch to change the direction of  
rotation. Depress the reversing switch lever from the A side  
for clockwise rotation or from the B side for counterclockwise  
rotation.  
A
B
1
CAUTION:  
Always check the direction of rotation before operation.  
1. Reversing switch lever  
Use the reversing switch only after the tool comes to a  
complete stop. Changing the direction of rotation before  
the tool stops may damage the tool.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before carrying out any work on the tool.  
001266  
Installing or removing driver bit or socket bit  
Use only the driver bit or socket bit shown in the figure. Do  
not use any other driver bit or socket bit.  
12 mm  
(15/32)  
9 mm  
(3/8)  
001267  
To install the bit, pull the sleeve in the direction of the arrow  
and insert the bit into the sleeve as far as it will go. Then  
release the sleeve to secure the bit.  
To remove the bit, pull the sleeve in the direction of the arrow  
and pull the bit out firmly.  
1
2
NOTE:  
If the bit is not inserted deep enough into the sleeve, the  
sleeve will not return to its original position and the bit  
will not be secured. In this case, try re-inserting the bit  
according to the instructions above.  
1. Bit  
2. Sleeve  
Hook  
The hook is convenient for temporarily hanging the tool. This  
can be removed without using a tool.This can be installed on  
either side of the tool.  
004355  
Installing and removing hook  
Expand the upper part of the hook in both directions and  
remove it. To install the hook, follow the removal procedure  
in reverse.  
1
1. Hook  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hold the tool firmly and place the point of the driver bit in the  
screw head. Apply forward pressure to the tool to the extent  
that the bit will not slip off the screw. Start the tool slowly and  
then increase the speed gradually. Release the switch trig-  
ger just as the screw bottoms out.  
OPERATION  
004356  
The proper fastening torque differs depending upon the kind  
or size of the screw/bolt, the material of the workpiece to be  
fastened, etc. Refer to the figure for the relation between fas-  
tening time and wood screw size. (Material to be fastened:  
Lauan)  
(S)  
12  
10  
8
NOTE:  
6
Use the proper bit for the head of the screw/bolt that you  
wish to use.  
4
When fastening tool screws in a steel plate, the proper  
fastening torque can be obtained in an extremely short  
time (approx. 0.1 - 0.2 seconds). Turn the tool off as  
soon as the impact sound is heard.  
2
0
4.2  
X65 X90 X125 X150  
mm  
5.0  
4.9  
5.7  
Screw size  
Hold the tool pointed straight at the screw or the screw  
and/or bit may be damaged.  
When driving wood screws, predrill pilot holes to make  
driving easier and to prevent splitting of the workpiece.  
The pilot holes should be slightly smaller than the wood  
screws in diameter.  
The size of wood screw which can be fastened with this  
tool may differ depending upon the type of material to be  
fastened. Always perform a test operation to determine  
the size of wood screw.  
When fastening bolts or nuts, always perform a test  
operation to verify the adequate fastening time for your  
bolt or nut. Excessive fastening torque may damage the  
bolt/nut or socket bit.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CAUTION:  
Always be sure that the tool is switched off and  
unplugged before attempting to perform inspection or  
maintenance.  
001145  
Replacing carbon brushes  
Remove and check the carbon brushes regularly. Replace  
when they wear down to the limit mark. Keep the carbon  
brushes clean and free to slip in the holders. Both carbon  
brushes should be replaced at the same time. Use only iden-  
tical carbon brushes.  
1
1. Limit mark  
004357  
Use a screwdriver to remove the brush holder caps. Take out  
the worn carbon brushes, insert the new ones and secure  
the brush holder caps.  
2
After replacing brushes, plug in the tool and break in brushes  
by running tool with no load for about 10 minutes. Then  
check the tool while running and electric brake operation  
when releasing the switch trigger. If electric brake is not  
working well, ask your local Makita service center for repair.  
1
1. Screwdriver  
2. Brush holder cap  
To maintain product SAFETY and RELIABILITY, repairs, any  
other maintenance or adjustment should be performed by  
Makita Authorized or Factory Service Centers, always using  
Makita replacement parts.  
ACCESSORIES  
CAUTION:  
These accessories or attachments are recommended for  
use with your Makita tool specified in this manual. The  
use of any other accessories or attachments might  
present a risk of injury to persons. Only use accessory or  
attachment for its stated purpose.  
If you need any assistance for more details regarding these  
accessories, ask your local Makita service center.  
Screw bits  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
First-Class  
Postage  
Required  
Post Office will  
not deliver  
without proper  
postage.  
Makita U.S.A., Inc.  
14930 Northam Street  
La Mirada, CA 90638-5753  
Fold  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIL THIS PORTION  
Your answers to the following questions are appreciated.  
1.This product was purchased from:  
3. How did you learn about this product:  
Home Center  
Other (  
)
Magazine  
Radio  
Hardware/Lumber Store  
Tool Distributor  
From Dealer  
Newspaper  
Store Display  
Catalog  
Exhibition  
From Friend  
Previous Usage  
Other (  
Industrial Supply  
Construction Supply  
)
2. Use of the product is intended for:  
4. Most favored points are:  
Construction Trade  
Industrial Maintenance  
Home Maintenance  
Hobby  
Design  
Repair Service  
Durability  
Power  
Features  
Size  
Price  
Other (  
)
Other (  
)
Makita Brand  
5. Any comments:  
DATE PURCHASED  
MONTH  
MODEL NO.  
DAY  
YEAR  
SERIAL NO.  
STATUS  
SEX  
Married Single  
M
F
INTL.  
LAST NAME / COMPANY NAME  
STREET ADRESS  
CITY  
AREA  
CODE  
STATE  
ZIP CODE  
PHONE  
40-49  
Under 19  
20-29  
30-39  
50-60  
Over 60  
AGE:  
BE SURE TO COMPLETE THE CUSTOMERS PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS.  
Please return this portion by facsimile or mail.  
Facsimile No: (714) 522-8133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
Paste  
FACTORY SERVICE CENTERS  
1-800-4-MAKITA  
RETAIN THIS PORTION FOR YOUR RECORDS  
ARIZONA  
FLORIDA  
MISSOURI  
PENNSYLVANIA  
1704 Babcock Blvd.  
Pittsburgh, PA 15209  
(412) 822-7370  
3707 E. Broadway Rd., Ste. 6  
Phoenix, AZ 85040  
(602) 437-2850  
750 East Sample Road  
Pompano Beach, FL 33064  
(954) 781-6333  
9876 Watson Road  
St. Louis, MO 63126-2221  
(314) 909-9889  
CALIFORNIA  
GEORGIA  
NEBRASKA  
PUERTO RICO  
41850 Christy St.  
Fremont, CA 94538-5107  
(510) 657-9881  
4680 River Green Parkway NW  
Duluth, GA 30096  
(770) 476-8911  
4129 S. 84th St.  
Omaha, NE 68127  
(402) 597-2925  
200 Guayama St.  
Hato Rey, PR 00917  
(787) 250-8776  
14930 Northam St.  
La Mirada, CA 90638-5753  
(714) 522-8088  
ILLINOIS  
NEVADA  
3375 S. Decatur Blvd.  
Suites. 22 - 24  
Las Vegas, NV 89102  
(702) 368-4277  
TENNESSEE  
1120 Elm Hill P.  
Suile 170 Nashville, TN 372  
(615) 248-3321  
1450 Feehanville Dr.  
Mt. Prospect, IL 60056-6011  
(847) 297-3100  
1970 Fulton Avenue  
Sacramento, CA 95825  
(916) 482-5197  
MARYLAND  
TEXAS  
7674 Clairemont Mesa Blvd.  
San Diego, CA 92111  
(858) 278-4471  
7397 Washington Boulevard,  
Suite 104 Elkridge, MD 21075  
(410) 796-4401  
NEW JERSEY  
12801 Stemmons Fwy Ste. 809  
Farmers Branch, TX 75234  
(972) 243-1150  
251 Herrod Blvd.  
Dayton, NJ 08810-1539  
(609) 655-1212  
16735 Saticoy St., Ste. 105  
Van Nuys, CA 91406  
(818) 782-2440  
12701 Directors Dr.  
Stafford, TX 77477-3701  
(281) 565-8665  
MASSACHUSETTS  
232 Providence Hwy.  
Westwood, MA 02090  
(781) 461-9754  
NEWYORK  
4917 Genessee Street  
Cheektowaga, NY 14225  
(716) 685-9503  
3453 IH-35 North, Ste. 101  
San Antonio, TX 78219  
(210) 228-0676  
COLORADO  
11839 E. 51st Ave.  
Denver, CO 80239-2709  
(303) 371-2850  
MINNESOTA  
6427 Penn Ave. South  
Richfield, MN 55423  
(612) 869-5199  
OREGON  
828 19th Avenue, N.W.  
Portland, OR 97209  
(503) 222-1823  
WISCONSIN  
Lincoln Plaza Shopping Ctr.  
2245 S. 108th St. West Allis, WI  
53227  
(414) 541-4776  
CUSTOMER’S RECORD  
Date Purchased  
When you need service: Send  
complete tool (prepaid) to one  
of the Makita Factory Service  
Centers listed, or to an Authorized  
Makita Service Center. Be sure  
to attach a letter to the outside of  
the carton detailing the problem  
with your tool.  
Dealer’s Name & Address  
Model No.  
Serial No.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Some dust created by power sanding, sawing, grinding, drilling, and other  
construction activities contains chemicals known to the State of California  
to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
lead from lead-based paints,  
crystalline silica from bricks and cement and other masonry products, and  
arsenic and chromium from chemically-treated lumber.  
Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well  
ventilated area, and work with approved safety equipment, such as those  
dust masks that are specially designed to filter out microscopic particles.  
MAKITA LIMITED ONE YEAR WARRANTY  
Warranty Policy  
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of  
defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.  
Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of  
Makitas Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective  
workmanship or material, Makita will repair (or at our option, replace) without charge.  
This Warranty does not apply where:  
repairs have been made or attempted by others:  
repairs are required because of normal wear and tear:  
the tool has been abused, misused or improperly maintained:  
alterations have been made to the tool.  
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL  
DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING  
AND AFTER THE TERM OF THIS WARRANTY.  
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF  
MERCHANTABILITYAND FITNESS FOR A SPECIFIC PURPOSE,AFTER THE ONE YEAR TERM OF THIS  
WARRANTY.  
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
Makita Corporation  
3-11-8, Sumiyoshi-cho,  
Anjo, Aichi 446-8502 Japan  
884513-069  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Laser Network Cables CB USBT R02 User Manual
LOREX Technology DVR DXR209161 User Manual
Mackie Stereo Amplifier 400F User Manual
Magnadyne Computer Monitor MV750G Gray User Manual
Magnasonic MP3 Docking Station MiDK101 User Manual
Makita Cordless Saw LXMT025 User Manual
Makita Impact Driver 6932FD User Manual
Marcum Technologies Radar Detector LX i User Manual
Martin Fireplaces Indoor Fireplace B36LA User Manual
Maytag Range CHG9800B User Manual