ECHNICAL INFORMATION
PRODUCT
T
P 1/ 8
Models No.
Description
9556HN, 9557HN, 9558HN
Angle Grinders 100mm (4"), 115mm (4-1/2"), 125mm (5")
L
CONCEPT AND MAIN APPLICATIONS
These angle grinders have been developed as sister models
of 9556NB series.
Features machined bevel gears more durable than sintered
bevel gears used for 9556NB series models.
H
W
9556HN is also available with plastic carrying case as
Model 9556HNK.
Dimensions: mm (")
9557HN is also available with plastic carrying case or
steel carrying case as Model 9557HNK.
9558HN is also available with steel carrying case as
Model 9558HNK.
Model No.
Length (L)
9556HN
9557HN
271 (10-5/8)
9558HN
Width (W) 118 (4-5/8) 129 (5-1/8) 139 (5-1/2)
Height (H) 97 (3-13/16)
106 (4-3/16)
AC/DC switch is used for the tools for USA and other
North American countries.
Specification
Continuous Rating (W)
Voltage (V)
Cycle (Hz)
Max. Output (W)
Current (A)
Input
840
840
840
840
840
Output
500
500
110
120
220
230
240
8.0
7.5
4.0
3.8
3.7
50/60
50/60
50/60
50/60
50/60
1,000
1,000
1,000
1,000
1,000
500
500
500
Model No.
Depressed center wheel
Capacity: mm (") Wire cup brush
Abrasive disc
Specification
9556HN
100 (4)
75 (3)
9557HN
9558HN
125 (5)
115 (4-1/2)
90 (3-1/2)
115 (4-1/2)
11,000
90 (3-1/2)
125 (5)
100 (4)
No load speed*1: min.-1 = rpm
Protection against electric shock
Power supply cord: m (ft)
Net weight*2: kg (lbs)
Double insulation
Australia, New Zealand: 2.0 (6.6), Other countries: 2.5 (8.2)
1.9 (4.2) 2.0 (4.4) 2.1 (4.6)
*1 North America: 10,000
*2 Weight according to EPTA-Procedure 01/2003
Standard equipment
9556HN
9557HN
9558HN
Depressed center wheel 100-36 .... 1 Depressed center wheel 115-36 .... 1 Depressed center wheel 125-36 .... 1
Lock nut wrench 20 ...................... 1 Lock nut wrench 28 ...................... 1 Lock nut wrench 35 ...................... 1
Grip 36 complete .......................... 1 Grip 36 complete .......................... 1 Grip 36 complete .......................... 1
Plastic or steel carrying case ......... 1 (for 9556HNK, 9557HNK, 9558HNK only)
Note: The standard equipment for the tool shown above may vary by country.
Optional accessories
Wheel covers, Depressed center wheels, Abrasive discs, Rubber pads (for abrasive discs), Sanding lock nuts,
Cut-off wheels, Super flanges (for 9557HN, 9558HN only), Wire cup brushes, Wire bevel brush (for 9556HN only),
Dust collecting wheel guards
Download from Www.Somanuals.com. All Manuals Search And Download.
P 3/ 8
Repair
[3] -1. Armature and Small Spiral Bevel Gear (cont.)
ASSEMBLING
Do the reverse of the disassembling steps.
Note: Use arbor press and Bearing Setting Plate (of proper size ) when fitting Ball bearing 629LLB
in Gear housing cover. (Fig. 4)
Important: Assemble Gear housing to Motor housing so that Switch lever can be operated with right thumb
as illustrated in Fig. 5.
Fig. 4
Fig. 5
[View from rear cover side]
Ball bearing 629LLB
Gear housing cover
Power supply cord
Switch lever
Rear cover
Tapping screw
4x18
Spindle
(Wheel)
Bearing setting plate
(of proper size)
[3] -2. Spiral Bevel Gear 37 and Ball Bearing 6201DDW
DISASSEMBLING
1) Remove Bearing box from Gear housing by unscrewing four M4x14 Pan head screws.
2) Remove Retaining ring S-12 and Wave washer 12 from Spindle with Retaining Ring S and R Pliers (No.1R291).
3) Spiral bevel gear 37 can now be removed by hand. Then remove Woodruff key 4. (Fig. 6)
4) Remove Spindle using Gear Extractor, large (No.1R045). Labyrinth ring can now be removed. (Fig. 7)
Fig. 6
Fig. 7
Spiral bevel gear 37
Gear Extractor, large (No.1R045)
Woodruff key 4
Bearing box
Labyrinth
ring
Spindle
Fig. 8
5) Remove Retaining ring R-32 from Bearing box
with Retaining Ring S and R Pliers (No.1R291).
6) By striking Bearing box against the surface of
a work bench, Ball bearing 6201DDW and Flat
washer 12 can be removed from Bearing box
as illustrated in Fig. 8.
Bearing box
If it is difficult to remove the ball bearing,
remove using arbor press.
Flat washer 12
Ball bearing
6201DDW
Download from Www.Somanuals.com. All Manuals Search And Download.
P 4/ 8
Repair
[3] -2. Spiral Bevel Gear 37 and Ball Bearing 6201DDW (cont.)
ASSEMBLING
Do the reverse of the disassembling steps.
Important: Do not to forget to install Labyrinth ring because it is an important part that prevents dust from entering
into Bearing box. (Fig. 9)
How to fit Retaining ring S-12 in place
See Fig. 10.
After installing Spiral bevel gear 37 and Wave washer 12 on Spindle;
1) Put Retaining ring S-12 on Retaining Ring Setting Jig (No.1R343) from the tapered end of the jig.
2) Put the jig onto Spindle, then put Bearing Setting Pipe 20-12.2 (No.1R028) over the jig.
3) Using arbor press, press down the pipe till the retaining ring is securely fitted in place on Spindle with a snap.
Fig. 9
Fig. 10
No.1R028
Labyrinth ring
Spindle
Retaining
ring S-12
Retaining
ring S-12
No.1R343
Bearing box
[3] -3. Disassembling/Assembling Shaft Lock Mechanism
DISASSEMBLING
Fig. 11
1) Remove Bearing box from Gear housing.
2) Pull off Shoulder pin 4 with pliers while pushing Pin cap with
finger. (Fig. 11)
Note: Do not pull off Shoulder pin 4 without holding Pin cap
because Compression spring 8 would sling Pin cap.
Shoulder pin 4
Gear housing
Compression
spring 8
ASSEMBLING
Push Shoulder pin 4 through Gear housing and Compression spring 8
into Pin cap.
Note: Do not reuse removed Pin cap because removal of Shoulder
pin 4 damages the inside surface of Pin cap, producing plastic
dust. Therefore, be sure to use a new Pin cap for replacement
and to remove all the plastic dust on Shoulder pin 4.
Pin cap
[3] -4. Tightening Tapping Screws That Fasten the Field
Tighten the two tapping screws that fasten Baffle plate and Field to the recommended torque of 1.1 - 1.3 Nm.
Download from Www.Somanuals.com. All Manuals Search And Download.
P 5/ 8
Circuit diagram
Color index of lead wires' sheath
Black
Red
Clear
Earth terminal (Ground terminal)
on the lead wire of Noise suppressor
Noise suppressor*
Brush holder A
Power supply
cord
Field
Switch
Brush holder B
*Some countries do not use noise suppressor
Brush holder A
Brush holder B
Download from Www.Somanuals.com. All Manuals Search And Download.
P 6/ 8
Wiring diagram
[1] Connecting Lead Wires of Power Supply Cord with Switch
Connect the lead wires with Switch as illustrated in Fig. 12.
Fig. 12
[When Spacer is used]
[When Spacer is not used]
Power supply cord
Switch button
Switch
Spacer
[2] Wiring of Field Lead Wires in the Rear of Motor Housing
[2] -1. Rear End
Route Field lead wires as illustrated in Figs. 13 - 16.
Fig. 13
[Lead Wires of Field]
Lead wire (black)
[Motor Housing with Field]
(view from Rear cover side)
Earth terminal on the lead wire (clear)
of Noise suppressor* has to be connected
to this portion.
Connect to Brush holder A.
Field
Brush holder A
Lead wire
(black)
Lead wire (white)
Switch lever
Lead wire (white)
Lead wire (black)
Connect to
Switch terminals.
Connect to Brush holder B.
Brush holder B
Spindle
*Some countries do not use noise suppressor.
Download from Www.Somanuals.com. All Manuals Search And Download.
P 7/ 8
Wiring diagram
[2] Wiring of Field Lead Wires in the Rear of Motor Housing (cont.)
[2] -2. Right Side and Bottom
Fig. 14
Right side view
Motor housing
Motor housing
Boss A
Bottom view
Boss A
Route the lead wire of Power supply cord to
Switch terminal No.2 so that it runs around the boss A.
Boss A
Boss A
Noise suppressor*
Switch
Switch
Field lead wire
(black)
Field lead wires
(white)
Motor housing,
viewed from right side
Motor housing,
viewed from bottom
Make sure that Field lead wires
are tight in Motor housing.
*Some countries do not use noise suppressor.
Download from Www.Somanuals.com. All Manuals Search And Download.
P 8/ 8
Wiring diagram
[2] Wiring of Field Lead Wires in the Rear of Motor Housing (cont.)
[2] -3. Left Side
Fig. 15
Earth terminal on the lead wire (clear)
of Noise suppressor* has to be connected
to this portion.
Left side view
Noise suppressor*
Make sure that Field lead wires
are tight in Motor housing.
*Some countries do not use noise suppressor.
[2] -4. Top
Fig. 16
Top view
Noise suppressor*
Earth terminal on
the lead wire (clear)
of Noise suppressor*
has to be connected
to this portion.
Sensor-matic tag
(anti-theft tag)
Put Sensor-matic tag** in this space.
*Some countries do not use noise suppressor.
**Some countries do not use sensormatic tag.
Download from Www.Somanuals.com. All Manuals Search And Download.
|