MAGNASONIC® WARRANTY
Consumer Electronics, Home Appliances and Home Office Products
For customer Assistance Call:
1-800-663-5954
Thank you for choosing MAGNASONIC®!
SYNNEX Canada Limited gives the following express warranty to the original consumer purchaser or gift recipient for this
MAGNASONIC product, when shipped in its original container and sold or distributed in Canada by SYNNEX Canada Limited or
by an Authorized MAGNASONIC Dealer:
SYNNEX Canada Limited warrants that this product is free, under normal use and maintenance, from any defects in material and
workmanship. If any such defects should be found in this product within the applicable warranty period, SYNNEX Canada Limited
shall, at its option, repair or replace the product as specified herein. Replacement parts furnished in connection with this warranty
shall be warranted for a period equal to the unexpired portion of the original equipment warranty.
PF0901M
This warranty shall not apply to:
9” Digital Photo Frame
a.
b.
c.
d.
Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or
inappropriate use as outlined in the owner's manual.
Any MAGNASONIC product tampered with, modified, adjusted or repaired by any party other than SYNNEX Canada
Limited or MAGNASONIC's Authorized Service Centres.
Damage caused or repairs required as a result of the use with items not specified or approved by SYNNEX Canada
Limited, including but not limited to head cleaning tapes and chemical cleaning agents.
Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the
product including but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus,
trays, filters, cables, paper, cabinet, cabinet parts, knobs, buttons, baskets, stands, shelves, cookware and cooking
utensils.
e.
f.
Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
Any damage caused by external or environmental conditions, including but not limited to transmission line/power line
voltage or liquid spillage.
Instruction Manual
g.
h.
i.
Any product received without appropriate model, serial number and CSA /cUL /cULus /cETL /cETLus markings.
Any products used for rental or commercial purposes.
Any installation, setup and/or programming charges.
Should this MAGNASONIC product fail to operate during the warranty period, warranty service may be obtained upon delivery of
the MAGNASONIC product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized
MAGNASONIC Service Centre. In-home warranty service may be provided at SYNNEX Canada Limited's discretion on any
MAGNASONIC television with the screen size of 27” or larger. This warranty constitutes the entire express warranty granted by
SYNNEX Canada Limited and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or
transfer this warranty on behalf of SYNNEX Canada Limited. To the extent the law permits, SYNNEX Canada Limited disclaims
any and all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of
profits resulting from a defect in material or workmanship relating to the product, including damages for the loss of time or use of
this MAGNASONIC product or the loss of information. The purchaser will be responsible for any removal, reinstallation,
transportation and insurance costs incurred. Correction of defects, in the manner and period of time described herein, constitute
complete fulfillment of all obligations and responsibilities of SYNNEX Canada Limited to the purchaser with respect to the product
and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
CARRY-IN PARTS & LABOUR WARRANTY PERIODS:
·Audio Products: 1 Year (Remote Control, if applicable – 90 Days)
·DVD Products: 1 Year (Remote Control – 90 Days)
·LCD & Plasma Display TV: 1 Year (Remote Control – 90 Days)
·Television Products: 1 Year (Remote Control – 90 Days)
·VCR Products: 1 Year (Remote Control – 90 Days, Video Heads – 6 Months)
·Home Appliances: 1 Year
o
o
Microwave Magnetron parts only additional 3 Years
Refrigerator / Freezer Compressor parts only, additional 4 years
·Heating / Cooling & Humidification Products: 1 Year (Remote Control – 90 Days)
Compressor parts only (if applicable), additional 4 years
o
·Home Office: 1 Year
To obtain the name and address of the nearest Authorized MAGNASONIC Service Centre or for more information on this warranty
-
-
Mail your inquiry to
SYNNEX Canada Limited
MAGNASONIC Customer Service
200 Ronson Drive, Toronto, ON M9W 5Z9; or
Call toll free 1-800-663-5954, Monday to Friday 9:00am – 5:00pm Eastern Time.
-
Thank you for your purchase of this Magnasonic product. Please read this Instruction Manual carefully
before using product to ensure proper use. Keep this manual in a safe place for future reference.
MAGNASONIC is a registered trade-mark
of SYNNEX Canada Limited
08.2007
Download from Www.Somanuals.com. All Manuals Search And Download.
Movie
Favorite - Used to view photos stored on the internal memory
Press the NAVIGATION buttons to select movie, then press ENTER To confirm the selection. After the
Picture Frame reads the files for several seconds, it begins to play the movie automatically. Press the
STOP button to return to the main menu during movie playback. Press PLAY/PAUSE to pause and
resume playback. NOTE: This unit supports MPEG4 format.
Use the NAVIGATION buttons to select the favorites option. Press ENTER to confirm the selection. This
begins to browse the files saved in the internal memory one by one. During playback press PLAY/ PAUSE
to pause or resume playback. Press the NAVIGATION buttons to rotate the picture. During a slide show,
press the STOP button, this enters Thumbnail Mode. To exit this option, press the MENU button.
Setup
Calendar
Select the setup option to display the setup menu. Use the NAVIGATION UP/DOWN keys to select the
desired item. Then press the NAVIGATION RIGHT button, the sub-options for each item will appear on the
right side of the screen.
Use the NAVIGATION buttons to select the CALENDAR function. Press ENTER to confirm the selection.
The calendar will be shown on the display. You can adjust the calendar by pressing the NAVIGATION
BUTTONS. Use the NAVIGATION LEFT/RIGHT buttons to adjust the year. Then use the NAVIGATION
UP/DOWN buttons to adjust the month. Use the STOP button to confirm your selection. Use the
NAVIGATION buttons to select the date, then press ENTER to confirm. To exit this function, press the
MENU button.
Photo Setting
Interval Time: To browse pictures at interval times, there are several options for you to set as follows:
off/5sec./10sec./15sec./30sec./1min./3min.
Transition Effect: Used to select one of the effects when changing from one picture to another. The
different settings are as follows: No effect/Cover up/Cover down/Cover left/Cover right/Uncover up/
Uncover down/Uncover left/Uncover right/Wipe up/Wipe down/Wipe left/Wipe right/Push up/Push down
/Push left/Push right/Random.
Clock
Use the NAVIGATION buttons to select the CLOCK Function. Then press ENTER to confirm the selection.
The current time will be shown on the screen in big characters; and the current date, month, year and
week will be shown under the time in small characters.
Auto Play
The options of auto play include photo and movie.
Alarm
Use the NAVIGATION buttons to select the ALARM function. Press ENTER to confirm the selection.
The options for the ALARM are as follows:
Display Setup
Enable: Press the NAVIGATION UP/DOWN button to make a selection between the two options (on/ off).
Set time: select this option to set the alarm time after the alarm is enabled. Use the NAVIGATION UP/
DOWN button to select the SET TIME option. Press ENTER to confirm the selection. Use the
NAVIGATION LEFT/RIGHT buttons to highlight the desired time to set. Then use NAVIGATION UP/
DOWN buttons to make the adjustments. Press the NAVIGATION RIGHT button to confirm and press
ENTER to exit the alarm time set mode. The Buzzer will sound at the pre-set alarm time (only if alarm is
enabled). NOTE: After the alarm buzzes and is turned off, it is required to turn the alarm back on again.
Otherwise, the alarm will not sound again once it reaches the pre-set time.
Use the following settings to change the display appearance:
TFT Brightness: to set TFT Brightness until desired effect is reached.
TFT Contrast: to set the TFT Contrast until desired effect is reached.
TFT Saturation: to set the TFT Saturation until desired effect is reached.
Custom Setup
OSD Language: The OSD language options are dependant on the software.
Style: Select one of following styles to display different setup menu styles. The options of styles are as
follows: Style 1/Style 2/Style 3/Style 4.
Copy/ Delete - Used to copy photos only onto the internal memory (approx. 15 photos max)
Use the NAVIGATION buttons to select the Copy/Delete function. Press ENTER to confirm the selection.
Select COPY or DELETE to enter the corresponding window where the file to be copied or deleted are.
Repeat Mode: Select one of following options to perform in repeat mode: off/one/folder/all.
Default: Select read to restore the setting.
Set Time: Use the NAVIGATION UP/DOWN buttons to select the SET TIME option, press ENTER to
confirm the selection. Use the NAVIGATION LEFT/RIGHT buttons to set the desired time. Then use the
NAVIGATION UP/DOWN buttons to adjust the time. After you have selected the desired time, press the
NAVIGATION RIGHT button to confirm the selection. Press ENTER To exit the clock time set and return to
the main menu.
Copy Function: when copy function is selected, all JPEG files in the USB Travel Drive or memory card
will be displayed in the file manager. use the NAVIGATION UP/DOWN buttons to select the files and
press ENTER to confirm the selection. The selected file will be highlight in a rectangle frame. When the
selection is finished, use the NAVIGATION buttons to select SAVE to save the selected files onto the
internal memory of the unit.
Exit
Select this option to exit the setup menu.
Delete Function: When DELETE is selected, all JPEG files saved will be displayed. Use NAVIGATION
buttons to select the files that you want to delete from the internal memory and press ENTER to confirm
the selection. The file you selected will be deleted.
Delete All: Press the NAVIGATION buttons to select delete all in the bottom menu. All the files in the
internal memory will be deleted.
Sort Mode: When Sort Mode is selected, use the NAVIGATION buttons to select the file that you want to
move and press ENTER to confirm. Then press the LEFT NAVIGATION button to move the picture up in
the sequence. (For example, move its sequence from 3rd position to 2nd position). Press the RIGHT
NAVIGATION button to move the picture down in the sequence. (For example, move its sequence from
3rd position to 4th position).
Press the NAVIGATION buttons to select RETURN to return to the edit mode. Select SLIDE SHOW to
browse the pictures one by one.
Remote Function Illustration
Power Button: Press this button to power on or off the player.
Mode Button: Press the MODE button once to display the clock time. Press this button twice to display
the calendar. Press this button three times to exit.
OSD Button: This button will display file/folder information on the screen (current file number, total files
number, current file name, and/or play time during movie playback mode).
Menu: Press MENU button during playback to return the main menu.
Play/Pause Button: Press PLAY/PAUSE button to pause during playback. Pressing this button again will
resume playback.
NOTE: The saving process may take some time to finish. Larger file sizes will take more time. Please don't
remove the USB Travel Drive or memory card, or turn off the power while saving. Doing so may case loss
or damage in the data on the USB Travel Drive, memory card, or internal memory.
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigation Buttons: Press the NAVIGATION buttons to select the desired items or to rotate the picture
during picture playback.
Interchangeable Faceplate
Enter Button: Press this button to confirm selection.
Stop: Press the STOP button to stop playback. Press PLAY/ PAUSE to resume playback.
F.BWD/ Previous: Pressing this button once during playback will skip a file or picture backwards.
Pressing and holding this button during normal playback of video or audio files will speed up the cycle with
each press as: 2X, 4X, 8X, 16X, 32X, Normal
Press PLAY to resume normal playback.
Faceplate
F.FWD/ Next: Press this button once during playback to skip a file or picture ahead. Press and holding this
button during normal playback of video or audio files will speed up the cycle with each press as:
2X, 4X, 8X, 16X, 32X, Normal
Press PLAY to resume normal playback.
Mute: Pressing the MUTE button, the audio output of the main unit will shut off. Pressing this button again
or the VOLUME buttons will resume the audio output.
Volume “+” & volume “-”: Press the volume “+” button to increase the volume level, and press the
volume “-” button to decrease the volume level.
Cleaning the Digital Photo Frame
1. Please make sure that you have turned off and unplugged the digital photo frame from the AC outlet
before cleaning it.
2. Don't put any liquid on the screen or the cabinet directly.
Insert
Cleaning the screen
1. Gently wipe the screen with a soft, lint-free cloth to remove dust and other particles that can scratch the
screen.
2. To clean the tough areas, use a soft, lint-free cloth with a few drops of water to remove stubborn dirt.
3. Never apply any pressure to the surface of the screen.
Pin
Cleaning the cabinet
1. Use a soft, dry cloth to clean the cabinet.
2. To clean the tough areas, use a soft, lint-free cloth with a few drops of water to remove stubborn dirt.
Hole (optional)
Hole (optional)
Please follow the above illustrations for proper assembly or disassembly of the face plates.
Assembly panel: To install the faceplate, locate the faceplate to the photo frame by aligning them point to
point as displayed above in the illustration. Clasp the panel slightly to assembly it into place.
Disassembly: To remove the faceplate, insert the provided metal tool (or other pointed metal object) into
each of two holes (optional) to release. Then lift the faceplate from the screen. If optional holes are
unavailable, then lift the faceplate from the screen directly.
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|