Magnadyne Automobile Alarm X7 User Manual

Owner’s  
Manual  
Model: X7  
For Technical Assistance, please call (800) 638-3600,  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Congratulations on your purchase of a quality Marksman automotive security and remote start  
system. Marksman automotive security products have been designed to provide the consumer with  
a product that is technologically superior and will provide years of trouble free operation. The  
information enclosed will provide a ready reference of the operation and maintenance of your new  
Marksman security and remote start system.  
Quick Reference Remote Transmitter Operation  
Use these illustrations as a reference while  
reading through the operating procedures.  
Transmitter  
Button  
System Function  
Remark  
Lock Doors and Arms System  
Arms and Deletes the Shock Sensor  
Press Twice within 5 Seconds.  
-
Car Locator  
Available 30 Seconds after System is Armed  
Press and Hold for 3 Seconds  
Panic Function (On-Off)  
Unlock Doors and Disarm System  
Two Steps Door Unlock and Disarm System Press Twice within 3 Seconds  
-
Silent Arming/Disarming  
Channel 3 (Trunk) Timer Control  
Passive Arming By-Pass  
Activate Remote Starter  
Press both at the same time  
+
Press and Hold for 1.5 Seconds  
While the System Disarmed.  
-
Press / Hold for 1 Second Release. Repeat  
Press / Hold for 1 Second Release. Repeat  
Press and Release for Car #2 Operation  
-
Turn Off the Remote Start  
Second System Operation  
-
II  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Security System Operation  
Manual Lock/Arm  
Using The Transmitter To Lock/Arm The Security System  
1. Press the  
button on the transmitter.  
2. The horn and parking lights will chirp/flash once indicating that the system is now armed.  
The vehicle’s doors will lock upon arming when interfaced with the security system.  
Silent Arming/Disarming:  
Pressing the  
button on the transmitter will arm or disarm your security system, no chirp  
+
sound will be heard, arm/disarm confirmation will be through the vehicles parking lights only.  
Defective Sensor Reminder:  
If the siren chirps 3 times, you have left open a hood, door or trunk.  
Shock Sensor Optional Sensor By-Pass:  
Press the  
button once, the siren chirps once, the security system is now armed. Press the  
button a second time within 5 seconds, the siren chirps twice, the shock sensor is now  
bypassed. The sensor bypass feature is programmed to activate for one arming cycle only. The  
security system will return to normal operation during the next arming cycle.  
Automatic Arming (Optional)  
The X7 is equipped with an optional automatic arming feature, which allows the security system  
to automatically arm itself 30 seconds after the last door is closed.  
1. Turn “OFF” the ignition key and exit the vehicle.  
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you  
re-open any protected entrance, the security system LED will stop flashing. It will begin  
flashing again when the vehicles entrances are closed.  
3. After the 30 second timer has elapsed, the security system will automatically “Arm”. The  
siren will chirp once and the parking lights will flash once.  
Automatic Arming with Automatic Door Locking: (Additional Option)  
With this option active, the vehicle’s doors will automatically lock after the automatic arming  
cycle has been completed.  
Automatic Arming Bypass:  
While the LED is flashing for automatic arming or automatic re-arm, press the  
button twice,  
the security system will respond with 1 chirp and LED will turn “On”. The security system will  
remain in this temporary state for as long as you wish. To exit passive bypass, press the  
“Lock” or “Unlock” button and the system will return to normal status.  
Note: While in Automatic Arming Bypass mode, you will be required to manually arm you  
system. Following the “Manual Lock/Arm” procedure above.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Security System Operation (continued)  
Manual Unlock/Disarm  
Using The Transmitter To Unlock/Disarm The Security System  
1. Press the  
button on the transmitter.  
2. The horn will chirp once and parking lights will flash once indicating that the system is now  
disarmed. The vehicle’s door will unlock upon arming when interfaced with the security  
system.  
Tamper Disarming:  
If the security system has been tampered with and activated, the siren will chirp 4 times and  
the parking lights will flash 3 times.  
Pathway Illumination: (Optional Feature)  
This feature turns ”On” the parking lights for 30 seconds upon disarming of the security  
system. Arming the security system will leave the parking lights on for 10 seconds.  
Two Step Door Unlocking: (Optional Feature)  
This feature will independently unlock the driver’s door only when disarming the security system.  
Pushing the “Unlock” button a second time within 3 seconds will unlock the entire vehicle.  
Automatic Re-Arm: (Optional Feature)  
If this feature is selected, the security system will automatically re-arm itself 60 seconds after  
disarming with the remote transmitter. Automatic re-arm will cancel if any door is opened  
before the 60 second timer has elapsed. Automatic re-arm will also re-lock the doors.  
Valet Mode Operation  
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand  
your transmitter to a parking attendant or garage mechanics. When the security system is in “Valet”  
mode, all functions and remote start functions are bypassed however, the remote panic feature and  
remote door locks will remain operational. To use the “Valet” mode, the security system must first be  
disarmed either by using your remote transmitter or by operating the manual override sequence.  
Enter Valet Mode:  
1. From the disarmed condition, turn the ignition to the “On” position.  
2. Push and hold valet switch for 2 seconds or until the “LED” turns on solid. The LED will  
remain on as long as the system is in “Valet” mode.  
Exit Valet Mode:  
1. To return to normal operation, turn the ignition switch “On”.  
2. Push and hold the valet switch for 2 seconds and the “LED” will turn off. This indicates the  
security system is out of the “Valet” mode.  
Emergency Override Operation  
The override function may be used if the remote transmitter is lost or inoperative.  
1. Enter the vehicle and turn the ignition switch to “On” position.  
2. Within 10 seconds push and release the valet switch, the security system will enter the  
“Emergency Override” mode. You can now start and operate the vehicle normally.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Security System Operation (continued)  
Remote Panic Alarm Operation  
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of  
emergency.  
1. Press and hold the  
button for 3 seconds. The alarm will immediately sound.  
button on the transmitter.  
button is pressed for panic, the car finder feature will trigger first then the  
2. To stop the security system from the “Panic” mode, press the  
Note: When the  
panic function will activate.  
Trigger the System (Shock Sensor and Entrance Protection)  
When the X7 is armed, your vehicle is protected by the shock sensor as follows:  
1. Light impacts to the vehicle body will trigger the pre-warning signal from the shock sensor.  
A long chirp from siren/horn.  
2. Heavy impacts, a door is opened, the hood is opened, the trunk is opened or the ignition key  
is turned on will trigger the horn/siren. The starter disable relay (if installed) will prevent the  
vehicle’s starter from cranking. The trigger cycle will last for 30 seconds then it will stop and  
automatically re-set and re-arm. If one of the sensors or detectors are still active the security  
system will sound a maximum of 6 times for a 30 second cycles.  
Interior Light Convenience Supervision (Option)  
If this option has been installed, it will operate in the following manner:  
1. Upon disarming, the interior lights will remain on for 30 seconds.  
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.  
Note: Turn on the ignition switch or arm the security system and it will turn off the dome light.  
Ignition Key Lock Control (Option)  
If the vehicles door locks have been interfaced to the security system, the security system will  
automatically lock the vehicle’s doors when the ignition is turned “On” and/or unlock the vehicle’s  
door when the ignition is turned “Off”. (Programming is required for this feature to be active).  
Trunk Release (Option)  
Press and hold the  
button on the transmitter for 1.5 seconds to activate the trunk release or  
other electronic devices.  
Car Locator  
The car locator feature of the X7 is progressive. After the X7 has been armed for 30 seconds,  
press the button to activate the car locator function. The siren/horn will sound 2 times and  
pause then sound two more times. The parking lights will flash 3 + 3 times. Press the  
button a  
second time and the siren/horn will sound 3 times and pause then sound four more times. The  
parking lights will flash 3 + 3 times. Press the button a third time and the siren/horn will sound  
6 times The parking lights will flash 6 times.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Start Operation  
User Warnings  
As with any product that performs automatic functions, there are certain safety precautions that  
you must practice and be aware of.  
1. Keep the transmitter out of reach of children.  
2. DO NOT leave anyone in the vehicle while running on remote control.  
3. Alert any service personal that the vehicle can be started automatically.  
4. DO NOT start the vehicle by remote while it’s in an enclosed area or garage.  
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.  
6. Should the unit malfunction, disconnect the fuse until the problem is corrected.  
7. The use and operations of this security system is the sole responsibility of the  
owner/operator of the vehicle.  
8. Some areas may have local ordinances that prohibit leaving a vehicle running on public  
streets. Check your local laws and ordinances.  
How to Remote Start Your Vehicle  
1. Press the  
button twice on the transmitter for about 1 second.  
2. The parking lights will activate to indicate the remote start signal has been received.  
3. The engine will start in approximately 5 seconds.  
4. Once the engine is running, after 11 seconds the parking lights will turn on again and climate  
controls will activate and adjust the vehicle’s interior temperature to your preset setting.  
5. The vehicle will run for 5 to 30 minute cycle and automatically shut down.  
Note: The remote start unit will not start the vehicle if any one of the following conditions exists:  
1. The hood is open.  
2. The brake pedal is pressed.  
3. Move the optional remote start enable switch to “Off” position (if installed).  
4. The gear selector is in any gear other than “Park” or “Neutral”.  
How to Operate the Vehicle While Running on Remote Start  
1. Insert the ignition key and turn it to the “On” position. Be sure you DO NOT turn the ignition  
key all the way to the “Start” position. This can cause severe damage to all the starter  
components on your vehicle.  
2. Press the brake pedal.  
Note: If the brake pedal is pressed before the key is in the “On” position, the engine will  
automatically shut down.  
Temporary Stop Operation  
This feature allows the vehicle to remain running after the key has been removed from the  
ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short  
periods of time but, would like to leave the motor running and climate control on.  
1. Before turning off the engine, press the  
button twice on the transmitter and the LED  
indicator will flash 3 times to confirm mode entry.  
2. Turn the ignition key to “Off” position (The engine will stay running).  
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Start Operation (continued)  
Timer Starting  
This unit can be programmed to start and run the engine every 2 or 3 hours. The engine will run  
for the programmed run time and then shut down. This feature is designed for an extreme cold  
climate. The system will automatically start the vehicle every 2 or 3 hours to prevent engine from  
cold hard to start and freezing over. A MAXIMUM OF SIX CYCLES CAN OCCUR.  
Important: Timer start should be used in open areas, never start and run the vehicle in enclosed  
spaces as a garage or carport  
To Activate the Start Timer:  
1. Press the  
the parking lights have turned on or flashing.  
2. Immediately depress the button then depress the  
button twice to remote start the vehicle. As soon as the vehicle is running and  
button. The parking lights will flash  
(3) times. The siren or horn chirps (3) times. The vehicle is now programmed to start  
every 2 or 3 hours.  
3. Press the brake pedal to stop the vehicle from running.  
Note: Unless the installer of this remote start system has reprogrammed the start timer for a 2 hour  
duration, the default programmed start time is set to 3 hours.  
Exit the Timer Start:  
Timer start can be exited manually as follows:  
1. Make sure the remote start system is not operating the engine.  
2. Turn the ignition to the “On” position. The LED and parking lights will flash (4) times. The  
horn or siren chirps (4) times.  
or  
1. Press the  
the parking lights have turned on or flashing.  
2. Immediately depress the button then press and hold the  
button twice to remote start the vehicle. As soon as the vehicle is running and  
button for 2 seconds. The  
parking lights will flash (4) times. The siren or horn chirps (4) times. The vehicle is no  
longer programmed to start automatically.  
Shut-Down Inputs for Remote Starter  
If any of the following conditions exist while the system is operating, the engine will not start or  
will shut down:  
1. The hood is open.  
2. The brake pedal is pressed.  
3. Move the optional remote start enable toggle switch to “Off” position (If installed).  
4. Engine is over-revved (Tachometer Checking Type).  
5. The pre-programmed run time 5-10-20-30 minutes has elapsed.  
6. Transmitter  
button is pressed twice.  
7. The vehicle refused to start running after 3 unsuccessful attempts.  
Disabling the Remote Start System  
This feature allows your security system’s remote start unit to be temporarily disabled to prevent  
the vehicle from being remote started accidentally. This feature is useful if the vehicle is being  
serviced or stored in an enclosed area. To disable the remote start, move the optional remote  
start enable toggle switch to the “Off” position. (If installed)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Start Operation (continued)  
Turbo Timer Mode (Also See Installation Manual)  
Turbo Timer mode keeps the engine running after arriving at you destination for a programmable  
time period of 1, 3 or 5 minutes. This allows the system’s time to conveniently cool down the  
turbo after you have left the vehicle.  
To Activate:  
1. While the engine is running, set the emergency brake and place the transmission to "Park".  
2. Before turning off the engine, press and release and buttons at the same time. The light  
will flash to indicate the remote start has entered “Turbo Timer” mode.  
3. Remove the “Ignition Key” from the key cylinder. The engine will keep running.  
4. Exit and secure the vehicle. The engine continues running until the pre-programmed time  
elapsed.  
Chirp Status Indications  
Parking Light Flash Indications  
Chirp  
Function  
Parking Lights  
1 Flash  
Function  
1 Chirp  
2 Chirps  
3 Chirps  
4 Chirps  
6 Chirps  
Arm  
Arm  
Disarmed  
2 Flashes  
Disarmed  
Defective Reminder  
Disarm / Triggered  
Car Locator  
3 Flashes  
Disarm / Triggered  
Car Locator  
Under Remote Control  
12 Flashes  
Constant On  
Alarm Operating Conditions  
Siren, Horn  
Parking Light LED  
Doors  
Starter  
Disable  
Dome Light  
1. Arming  
1 or 3 Chirps 1 Flash  
Slow Flash Locking  
2. Disarming 2 or 4 Chirps 2 or 3 Flashes Fast Flash  
Unlocking  
Turns on for 30 Seconds  
3. Trigger  
4. Panic  
Alarming  
Alarming  
Flashes  
Slow Flash  
Disable Flashes  
Flashes  
Flashes  
5. Car Locator 6 Chirps  
12 Flashes  
LED Status Indications  
LED  
Function  
LED  
Function  
Off  
Disarmed  
Armed  
2 Flashes... pause  
3 Flashes... pause  
4 Flashes... pause  
5 Flashes... pause  
Zone 2: Trigger on Trunk/Hood  
Zone 3: Trigger on Door Switch  
Zone 4: Trigger on Optional Sensor  
Zone 5: Trigger on Ignition Switch  
Slow Flash  
Fast Flash  
On (Solid)  
Passive Arming  
Valet Mode  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts and Accessories for  
Remote Mobile Security Systems  
DESCRIPTION  
MODEL #  
$ PRICE  
ORDER BY MAIL  
Uses 3 volt CR2032 Lithium Battery (2 pcs.)  
Replacements:  
CR2032  
Radio Shack: #23-162 (CR22032)  
Duracell: #DL2032  
Eveready: #ECR2032  
Panasonic: # CR2032  
4-Button Transmitter with SAW  
Technology for:  
X7RF  
$44.95 ea.  
X7 Remote Start Security System.  
6-Tone, 118dB Siren: For use with all  
Remote Mobile Security Systems.  
ALA115  
ALA125  
$34.95 ea.  
$39.95 ea.  
6-Tone, 130dB Siren: For use with all  
Remote Mobile Security Systems.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts and Accessories Order Form  
Mail to: Magnadyne Corporation  
Credit Card or Money Order Only  
ATTN: Consumer Parts Sales  
P.O. Box 5365  
Carson, CA 90749-5365  
(Sorry No Cash, C.O.D. or personal checks accepted)  
SHIP TO: (No P.O. Boxes)  
LAST NAME  
FIRST NAME  
INITIAL  
STREET ADDRESS  
ADDITIONAL ADDRESS  
ADDITIONAL ADDRESS  
CITY  
STATE  
ZIP CODE  
DAY TIME PHONE NUMBER  
CREDIT CARD INFORMATION  
VISA  
MC  
CREDIT CARD N0.  
CARD HOLDER’S LAST NAME  
STREET ADDRESS  
CITY  
EXPIRATION DATE  
FIRST NAME  
INITIAL  
STATE  
QTY.  
ZIP CODE  
PART #  
DESCRIPTION  
PRICE EACH  
TOTAL  
Shipping and Handling  
Sales Subtotal = ________ . ______  
Up to $20.00  
20.01 to 30.00  
30.01 to 45.00  
45.01 to 70.00  
Over 70.01  
$5.00  
5.95  
6.50  
6.95  
7.95  
California Residents Add Sales Tax = ________ . ______  
Shipping and Handling (See Chart) = ________ . ______  
TOTAL = ________ . ______  
On regular orders please allow 4-5 weeks for delivery.  
Please give a shipping address where this order may be delivered between the hours of 9 a.m. and 5 p.m. weekdays.  
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Lifetime Warranty  
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original  
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the  
option of the Magnadyne Corporation or its authorized agents, if said product or part is found  
defective in materials or workmanship, when properly connected and operating on the correct  
power requirements designated for the specific product. This warranty and Magnadyne Corporation  
or its authorized agents obligations, hereunder do not apply where the product was: damaged while  
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably  
maintained, utilized in commercial or industrial operation, or serviced by anyone other than  
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken  
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its  
authorized agents do not assume any labor costs for the removal and reinstallation of any product  
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized  
agents. Such costs are the sole responsibility of the purchaser.  
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories  
used in connection with the product resulting from improper installation, alteration, accident, misuse,  
abuse or acts of nature.  
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither  
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile  
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness  
or any accessory item are covered by our standard 12 month limited warranty.  
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential  
or incidental damages or claims that may arise due to failure of product to operate properly  
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,  
replacement of the product as stated above if all conditions of the warranty are met. No  
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does  
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or  
against the loss or damage to the contents of any vehicle in which a security system is installed.  
Magnadyne security systems are only a deterrent against possible theft.  
This warranty extends only to the original purchaser of the product and for the vehicle in which it  
was originally installed. This warranty is not transferable or assignable to any person or vehicle.  
Defective merchandise should be returned to the original point of purchase or secondly to  
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must  
be obtained before sending, or merchandise may be refused.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© Copyright 2008 Magnadyne Corporation  
X7-UM 3-11-08 Rev. A  
Download from Www.Somanuals.com. All Manuals Search And Download.  

LaCie Computer Drive Little Big Disk Thunderbolt Series User Manual
Land Pride Compact Loader SR2572 User Manual
Liebherr Refrigerator CS 1601 User Manual
Life Fitness Elliptical Trainer 91XW 0XXX 01 User Manual
Lincoln Kitchen Utensil Countertop Impinger User Manual
Lindy Network Card 42982V0 User Manual
Magnavox DVD Player MWD200F User Manual
Maretron Network Router IPG100 User Manual
Market Forge Industries Cookware ST 3E User Manual
McCulloch Lawn Mower 532 43 45 09 Rev 1 User Manual