User’s Manual
Model: M8a
For Technical Assistance, please call (800) 638-3600,
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard Remote Transmitter Operation
Transmitter Button
System Function
Remark
Lock Doors & Arm System
Arm and Delete the 2 Stage Shock Sensor
Arm System and Hidden Alarm Function
Car Locator
Press Twice within 3 Seconds
Press within 3 Seconds
-
-
When System is Armed
(3 Second)
Panic Function
Press and Hold for 3 seconds
Ignition in "Off" Position
Silent Arming / Disarming
Active Anti-Car Jacking Mode
+
Ignition in "On" Position Press and
Hold for 2 seconds
+
(2 Second)
Unlock Doors & Disarm System
Two Steps Door Unlock & Disarm System
Trunk Release (Channel 3)
Press Twice within 3 Seconds
Press and Hold for 2 Seconds
While the System is Disarmed
Press Twice within 3 Seconds
-
(2 Second)
Passive Arming By-pass
-
-
+
Activate or Turn Off The Remote Start
Channel # 4 Timer Output (4)
Channel # 5 Timer Output (5)
Channel # 6 Timer Output (6)
Switch Code for Second Car Control
+
+
2-Way LED Remote Control Transceiver Operation Only
Transmitter Button
System Function
Remark
Button Lock
Press within 3 Seconds and Hold
Button for 2 Seconds
-
(2 Second)
-
-
(C) System’s Status Check
Optional Driving Pager
Melody Sound On / Off
Press within 3 Seconds
Press within 3 Seconds
-
Press within 3 Seconds and Hold
Buttons for 2 Seconds
-
(2 Second)
(M)
Last Trigger Memory Retrieval
Power Save Mode
Press within 3 Seconds
-
-
Press within 3 Seconds and Hold
Buttons for 3 Seconds
(3 Second)
Switching Code for 2nd/1st Car Operation
Press within 3 Seconds and Hold
+
-
and
Buttons for Together
(2 Second)
for 2 Seconds
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The factory default setting at “Power Save Mode”, before operation the 2-way LED remote
control transmitter, press the button first, within 3 seconds press and hold the button
for 3 seconds, with two beeping sound to indicate exit the “Power Save Mode” and all remote
transmitter is on function.
Power Save Mode
The power save mode allows you to temporarily bypass all remote transmitter functions. While in
power save mode, the LED remote transmitter uses no current in order to save the battery power,
and the “beep” sound will always be muted .
Entry: Press the
button first, within 3 seconds press and hold the
button for 3
seconds, with long beeping sound to indicate entry into the “Power Save Mode” and all remote
transmitter functions will be temporarily bypassed.
Exit: Press the
button first, within 3 seconds press and hold the
button for 3
seconds, with two beeping sound to indicate exit of the “Power Save Mode” and all remote
transmitter functions return.
Button Lock
Button lock is useful if you want to temporarily disable the transmission function of the remote
control to prevent any inadvertent pressing of buttons. Press the
button first, within 3
seconds press and hold the
button for 2 seconds to activate or cancel the “Button Lock”
function. The “beep” sound is muted while buttons are pressed, and the LED will flash for a few
seconds to show the remote control transmitter is in “Button Lock” mode.
Out of Range Indication: (Also See Installation Manual)
The system will automatically check the range every 20 minutes after being armed. If user is out
of range, the transmitter will emit five short “Beep” sounds.
LED Display
LED
Function
Off
System is Disarmed
Slow Flash
Fast Flashing
On Solid
System is Armed
System in Passive Arming
System in Valet Mode
Zone 1 - Warn Away Trigger
Zone 2 - Trigger on Trunk/Hook
Zone 3 - Trigger on Door Switch
Zone 4 - Trigger on Shock Sensor
Zone 5 - Trigger on Ignition Switch
2 Flashes - Pause
3 Flashes - Pause
4 Flashes - Pause
5 Flashes - Pause
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chirp Indicators
Chirp
Parking Lights
Chirp
Function
Function
1 Chirp
System is Armed
System is Disarmed
Door Ajar Warning
Disarm/Triggered
Car Locator
1 Flash
System is Armed
System is Disarmed
Disarmed/Triggered
Car Locator
2 Chirps
2 Flashes
3 Chirps
3 Flashes
4 Chirps
12 Flashes
Constant On
6 Chirps
Under Remote Start
Alarm Operating Condition
Siren/Horn
Parking Light
LED
Doors
Starter
Dome Light
1. Arming
1 or 3 Chirps
2 or 4 Chirps
1 Flash
Slow Flash
Locking
Disabled
Turns on for
30 Seconds
2. Disarming
2 or 3 Flashes
Unlocking
3. Trigger
Alarming
Alarming
Alarming
6 Chirps
Flashes
Flashes
Slow Flash
Disabled
Disabled
Flashes
Flashes
Flashes
4. Panic
5. Car Jacking
6. Car Locator
Flashes
12 Flashes
Locking
Active Arming (Lock and Arm)
1. Press the button on the transmitter.
2. The siren will chirp once and parking light will flash once indicating that the system is now
armed. The vehicle door will lock upon arming when interfaced with the security system.
Actions of the 2-Way LED Remote Control Transceiver
ARM
LED
Melody Sound
One Chirp
Arm
LED turns on for 2 seconds
LED flash for 15 seconds
LED flash for 15 seconds
Arm and Hood / Trunk Ajar
Arm and Door Ajar
Three Chirps
Three Chirps
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ajar Warning:
If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar (Depending on how
your system is programmed, you will hear the chirps immediately or within 30 seconds).
Silent Arming/Disarming:
Press the transmitter
and
button at the same time to arm or disarm your security system.
No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking
lights only.
Shock Sensor By-Pass:
Press the button on the transmitter two times within 3 seconds to arm the security system and
bypass the shock sensor. The system will chirp one additional time to confirm the sensor bypass
mode was activated. The sensor bypass feature is programmed to activate for one arming cycle
only. The security system will return to normal operation during the next arming cycle.
Hidden Alarm Function:
Press the
button first, within 3 seconds press the
button to activate the hidden alarm
function. The security system will arm with “Hidden Alarm Function”. The siren / horn will be
silenced even if the sensor is triggered in the armed status.
Passive Arming
Active arming / disarming is controls your security system via the remote transmitter. This security
system is equipped with an optional Passive Arming feature, which allows the security system to
arm 30 seconds after the last door is closed. Operation is as follows:
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you
reopen any door / hood / trunk, the security system LED will stop flashing. It will begin
flashing again once all the vehicle’s entrances are closed.
3. After the 30-second timer has elapsed, the security system will automatically “ARM”. The
siren will chirp 1 time and the parking lights will flash 1 time.
Passive Arming with Passive Door Locking: (See Installation Manual)
The vehicle doors will automatically lock after passive arming cycle has been completed.
Passive Arming By-Pass:
While the system is disarmed, press the
button twice, the security will respond with 1 chirp
and the LED will turn “ON”. The security system will remain in this temporary state for as long as
you wish. Press the transmitter
to normal status.
or button to exit passive bypass, and the system will return
Active Disarming (Unlock and Disarm)
1. Press button on the transmitter.
2. The siren will chirp twice and parking lights will flash twice to indicating that the security system
is now disarmed. The vehicle’s door will unlock and dome light turns on for 30 seconds upon
disarming when interfaced with the security system.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Actions of the 2-Way LED Remote Control Transceiver
LED
Melody Sound
2 Chirps
Disarm
LED turns on for 2 seconds
LED flash for 15 seconds
LED flash for 15 seconds
LED flash for 15 seconds
LED flash for 15 seconds
Hood / Trunk Trigger
Door Trigger
4 Chirps
4 Chirps
Shock Sensor Trigger
Ignition Trigger
4 Chirps
4 Chirps
Tamper Disarming:
If the alarm is triggered upon disarming the system, the siren will chirp 4 times and the parking
light flash 3 times.
Pathway Illumination: (See Installation Manual)
This feature turns the parking lights “ON” for 30 seconds upon a unlock signal, and for 10
seconds upon the lock signal.
Two Step Door Unlock: (See Installation Manual)
This feature will independently unlock the driver’s door only when disarming the security system.
Pushing the button a second time within 3 seconds will unlock the other doors.
Automatic Re-Arm: (See Installation Manual)
If this feature is selected, the security system will automatically re-arm itself in 60 seconds after
disarming with the remote transmitter. Automatic rearm will cancel if any door is opened before
the 60 second timer has elapsed.
Second Vehicle System Control
Standard 5-Button Transmitter
The transmitter supplied can operate a second system in another vehicle by repeating the following steps:
1. Press the
button one time prior to attempting control of the second vehicle system. The
LED indicator on the transmitter will be on for 2 seconds.
2. Press the button on the transmitter to perform the function you want (arm/disarm, open the
trunk, etc.). Each time you press the
function.
button, you will have 2 seconds to activate one
2-Way LED Transmitter
Unlike the standard transmitter, the LED transmitter can be permanently switched over to control a
second vehicle for any length of time by performing these steps:
1. Press and release the button, then press the and buttons together and hold them for 2
seconds. The transmitter will beep 2 times, and the
and
LEDs will slowly flash.
2. Press the button that you want to control the second vehicle function. While in the 2nd car
mode, each time you press a control button, the transmitter will beep 2 times indicating a
second car function.
3. To return to primary vehicle control, repeat Step 1 above. The transmitter will beep 1 time to
indicate that it is back to controlling the primary vehicle. When any function button on the
transmitter is pressed, the transmitter will beep 1 time to indicate first car function control.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Disarming without a Transmitter
The override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to the “ON” position (alarm will sound).
2. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter
the disarm mode. You can now start and operate the vehicle normally.
Valet Mode (System in Disarm or Valet Mode)
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to give
your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all
alarm functions and remote start functions are bypassed. However, the remote panic feature and
remote door locks will remain operational. To use the valet mode, the system must be disarmed
either by using you remote transmitter, or by operating the manual override sequence.
Enter Valet Mode:
1. From the disarmed mode, turn the ignition to the “ON” position.
2. Push and hold the valet switch for 2 seconds until the LED turns on. The LED will remain on
as long as the system is in “Valet Mode”.
Exit Valet Mode:
1. To return to normal operation, turn ignition “ON”.
2. Push and hold valet switch for 2 seconds. The LED will turn off indicating the system is
exiting the valet mode.
Actions of the 2-Way LED Remote Control Transceiver
LED
Melody Sound
Remote Door Lock
Zzz LED turns on for 2 seconds
1 Chirp
Remote Door Unlock
Zzz LED turns on for 2 seconds
2 Chirps
Car Locator
When armed, press the button to active car locator function. The siren will then chirp 6 times and
the parking lights will flash 12 times.
Actions of the 2-Way LED Remote Control Transceiver Melody Sound
Melody Sound
Car Locator
One “Activate” Melody Sound
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Panic Function (Also See Installation Manual)
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of
emergency:
1. Press and hold the button for 3 seconds. The alarm will immediately sound.
2. During panic mode, the normal function of this transmitter button will be suspended. The
transmitter and buttons can be used to lock and unlock the door (if the option is installed).
However, once the button is pressed, the vehicle’s starter disable device, (when installed)
will enable the vehicle to start.
3. To stop the alarm, press and hold the transmitter or button again for 3 seconds. Also, if
any transmitter button other than or button is pressed and released, the panic mode will
be turned off immediately.
4. If the button is not pressed, the alarm will automatically stop after 30 seconds.
Trigger the System
When armed, your vehicle is protected as follows:
1. Light impact will trigger the warn-away signal.
2. Heavy Impacts / Doors Open / Hood Open / Trunk Open / Turning on the Ignition Key will
trigger the programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren,
horn, parking lights and dome light will turn on to alert of an intrusion for 30 seconds. Then it
will stop and automatic reset and rearm. If any one of sensors or detectors are still active, the
alarm system will sound a maximum of 6 times of 30 seconds cycles.
Actions of the 2-Way LED Remote Control Transceiver
LED
Melody Sound
Hood / Trunk Trigger
Door Trigger
LED flash for 15 seconds
LED flash for 15 seconds
“Zone 2” Melody Sound for 10 seconds
“Zone 3” Melody Sound for 10 seconds
One Warning Sound
Warn-Away Trigger
Shock Sensor Trigger
Ignition Trigger
LED flash for 15 seconds
LED flash for 15 seconds
“Zone 4” Melody Sound for 10 seconds
“Zone 5” Melody Sound for 10 seconds
Noise Abatement Circuit:
The Noise Abatement Circuit prevents annoying repetitive trigger sequences due to faulty door
pin switches or environmental conditions such as thunder, airport noise, etc.
The alarm triggers 5 times. Each time, the same sensor / switch is triggering the alarm. The
Noise Abatement Circuit will interpret this pattern of triggers as a false alarm. After the fifth
trigger, the Noise Abatement Circuit ignores, or bypasses, that sensor / switch until the other
sensor / switch is triggered.
The Noise Abatement Circuit covers doors (hood / trunk) differently: If the alarm is triggered by
an open door for six full cycles, the doors will be bypassed until the trigger ceases.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Anti-Car Jacking
Warning: If you don't require the anti-car jacking function in this alarm system, be sure that it is set
to “OFF”. The default setting for anti-car jacking is “OFF” (See Installation Guide).
Active Anti-Car Jacking:
1. Press and hold the transmitter
and
button at the same time for 2 seconds while the
vehicle’s ignition is ON. The parking lights will turns on for 1.5 seconds to indicate the system
has entered the anti-car jacking mode.
2. If you are forced from the vehicle while in the anti-car jacking mode, the system will be
triggered when the door is opened and closed while the ignition is “ON”.
Passive Anti-Car Jacking:
1. Turn the ignition switch to the “ON” position. The system will then enter the anti-car jacking mode.
2. Once in the anti-car jacking mode, and you are forced from the vehicle, the system will trigger
when the door is opened and closed while the ignition is “ON”.
Trigger the Anti-Car Jacking Mode:
1. 50 seconds after the system has been triggered, the siren will start chirping for 15 seconds.
2. During this 15 second period of chirping, you will be alerted to push the valet switch once to
turn off the anti-car jacking feature. If not, it will enter a second timer car jacking.
3. 65 seconds after the system has beer triggered, the siren starts sounding and the parking
lights start flashing.
4. 90 seconds after the system has been triggered:
A. The siren will still be sounding and the parking lights start flashing.
B. The starter disable will be activated to prevent the vehicle from starting.
C. It will remain active until the vehicle's battery power is exhausted.
Override the System to Turn Off Anti-Car Jacking:
Turn the ignition switch from “OFF” to “ON”, and within 10 seconds push valet switch, the siren
will stop and the system will be disarmed.
Last Trigger Memory Retrieval (For 2-Way Transceiver Operation Only)
If you are out of range and you want to retrieve last trigger’s memory storage in the 2-way remote
control transceiver, press the
button first within 3 seconds, then press the
(M) button. One
melody sound and the last trigger’s memory storage in the transmitter will immediately be
displayed on the LED.
Actions of the 2-Way LED Remote Control Transceiver
LED
Hood / Trunk Trigger
Door Trigger
LED flash for 15 seconds
LED flash for 15 seconds
LED flash for 15 seconds
LED flash for 15 seconds
Shock Sensor Trigger
Ignition Trigger
10
Download from Www.Somanuals.com. All Manuals Search And Download.
System Status Check (For 2-Way Transceiver Operation Only)
Press the
button twice to check the system’s present status through the 2-way transceiver, then
within 3 seconds press the (C) button. One melody sound and all the system’s present status will
immediately displayed on the LED.
Actions of the 2-Way LED Remote Control Transceiver
LED
Armed
LED turns on for 5 seconds
LED turns on for 5 seconds
Disarmed
Valet Mode
Engine Running
Hood/Trunk Ajar
Door Open
Zzz LED turns on for 5 seconds
LED Fast flash for 15 seconds
LED flash for 15 seconds
LED flash for 15 seconds
Driver Paging (For 2-Way Transceiver Operation Only)
Driver Paging is useful in the event that someone wants to page the driver of the parked vehicle.
Indoor Driving Paging:
With the ignition switch “OFF”, press and hold the valet switch for 2 seconds to page the driver.
One chirp sound shall be emitted from the vehicle and the paging melody sound continues
sounding from your 2-way remote control transceiver.
Outdoor Driving Paging:
If someone tries to page you by tapping the optional paging (knock) sensor, which is usually
mounted on the lower part of front windshield, the paging melody sound continues sounding
from your 2-way remote control transceiver.
1. Press the
button first, within 3 seconds press the
button to activate outdoor driver
paging function. It responds with chirps from the vehicle, and a melody sound from the
remote control transceiver to confirm the function is on.
2. When tapping the paging sensor, one chirp sound shall be emitted from the vehicle and the
paging melody sound continues sounding for 15 seconds from your 2-way remote control
transceiver.
3. Turn “ON” the ignition switch; OR press the button to arm the system; OR press the button
to disarm the system, the outdoor driver paging function will exit.
Actions of the 2-Way LED Remote Control Transceiver
Melody Sound
Driver Paging
“Telephone” Melody Sound for 10 Seconds
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Dome Light Convenience Delay and Supervision
The alarm has a unique feature which will turn on your vehicle dome light as follows:
1. Upon disarming, the interior light will remain on for 30 seconds.
2. If the vehicle is intruded, the interior light will flash for the same duration as the siren.
Note: To turn off the dome light, turn on the ignition switch or arm the alarm.
(Also See Installation Manual)
Ignition Control Door Lock/Unlock
If the vehicle’s door locks have been interfaced to the security system, the system will
automatically lock the vehicle's doors when the ignition is turned “ON” and / or unlock the
vehicle’s doors when the ignition is turned “OFF”.
Trunk Release (Channel 3) Output
Press and hold the
other electric devices.
button on the transmitter for two seconds to active the trunk release or
(Also See Installation Manual)
Channel 4 Timer Control Output
Press the transmitter
(4) and
(4) button at the same time to activate Channel 4 function.
Channel 4 is user-programmable timer output. You may program the built-in timer to send a
ground signal for any time duration from 1 to 120 seconds. For instance, this timer output may
be used to turn on the headlights, power windows or sunroof (factory defaults setting at
momentary output).
Channel 5 Timer Control Output
Press the transmitter
(5) and
(5) buttons at the same time to active Channel 5 function.
Channel 5 is user-programmable timer output. You may program the built-in timer to send a
ground signal for any time duration from 1 to 120 seconds. For instance, this timer output may
be used to turn on the headlights, power windows or sunroof (factory defaults setting at
momentary output).
(Also See Installation Manual)
Channel 6 Timer Control Output
Press the transmitter
(6) and
(6) buttons at the same time to active Channel 6 function.
Channel 6 is user-programmable timer output. You may program the built-in timer to send a
ground signal for any time duration from 1 to 120 seconds. For instance, this timer output may
be used to turn on the headlights, power windows or sunroof (factory defaults setting at
momentary output).
Power On Memory
This security system is equipped with circuitry that will allow the unit to remember its alarm
state if the power is lost and then reconnected.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE START OPERATION
To Remote Start the Vehicle
1. Press the
button twice on the transmitter.
2. The parking lights will be activated, indicating the remote start received the signal.
3. The engine will start approximately 5 seconds.
4. Once the engine is running, after a couple seconds the parking light will turn on again and
climate controls will activate and adjust the vehicles interior temperature to your preset setting.
5. The vehicle will run for a 5 to 30 minute cycle and automatically shut down.
Note: The Remote Start Unit will not start the vehicle if any one of the following conditions exist:
A. The hood is opened.
B. The brake pedal is pressed.
C. Move the optional remote start enable switch to “OFF” position (If installed).
D. The gear selector is in any gear other then “PARK” or “NEUTRAL”.
Actions of the 2-Way LED Remote Control Transceiver
LED
LED Fast Flash for 2 Seconds
LED Fast Flash for 60 Seconds
Melody Sound
Activate Remote Start
Engine Running
One “Activate” Melody Sound
“Beep Sound” for 5 Seconds
One “Stop” Melody Sound
Stop The Remote Start
(Also See Installation Manual)
Safe Start
Press the button twice on the transmitter to start the vehicle (factory default setting). If your
transmitter has been programmed to the “Safe Start” feature, press the
same time to remotely start the vehicle.
and buttons at the
To Operate the Vehicle While Running on the Remote Start
1. Insert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the “ON” position, the engine will shut
down.
Temporary Stop Feature
This feature allows the vehicle to remain running after the key has been removed from the
ignition. It is useful when you wish to exit and lock the vehicle for short periods of time, but
would like to leave the motor running and the climate control on.
1. Before turning off the engine, press the
indicator will flash 3 times to confirm.
button twice on the transmitter and the LED
2. Turn the ignition key to the “OFF” position (the engine will stay running).
3. The engine will run until the pre-programmed time elapsed or shutdown input is received.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
(Also See Installation Manual)
Turbo Timer Mode
Turbo Timer Mode keeps the engine running after arriving at you destination for a programmable
time period of 1, 3 or 5 minutes. This allows the system’s time to conveniently cool down the turbo
after you have left the vehicle.
To Activate:
1. While the engine is running, set the emergency brake and place the transmission to "Park".
2. Before turning off the engine, press and release and buttons at the same time. The light
will flash to indicate the remote start has entered turbo charge mode.
3. Remove the “Ignition Key” from the key cylinder. The engine will keep running.
4. Exit and secure the vehicle. The Engine continues running until the pre-programmed time
elapsed.
Timer/Temperature Start
This unit can be programmed to start and run the engine every 3 hours. The engine will run for the
programmed time and then shut down.
IMPORTANT: Timer Start should be used only in open areas. Never start and run a vehicle in an
enclosed space such as a garage or carport.
3-Hour Timer Start with Temperature Control “OFF”:
This feature is designed for use in a extremely cold climate. The system will auto start the vehicle
every 3 hours to help prevent the engine from freezing. A Maximum of Six Cycles Can Occur.
3-Hour Timer Start with Temperature Control: (Also See Installation Manual)
The system can be programmed to automatically start the vehicle engine whenever the
temperature inside the vehicle reaches or drops below the preprogrammed temperature level.
The system will monitor the air temperature every 3 hours and will only start the engine during
extremely cold temperatures. There are three temperature level to choose from (see installation
manual).
Enter the Timer Start:
1. Press the
button twice to remote start the vehicle.
2. As soon as the vehicle is running and the parking lights have turned on or have flashed, within
2 seconds press the
3. Rapidly press the
button once.
button (or depresses
+
buttons, if you have programmed these
buttons for "Safe Start"). The parking light will flash 3 times. The siren or horn will chirp 3
times. The vehicle is now programmed to start every 3 hours.
4. Press the brake pedal to stop the vehicle running.
Exit the Timer Start:
1. Make sure the remote start system is not operating the engine.
2. Turn the ignition on. The LED and parking light will flash 4 times. The horn will chirp 4 times.
Or
1. Press the
2. As soon as the vehicle is running and the parking lights have turned on or flash, immediately
press the button, then press and hold the button for 2 seconds (or press buttons,
button twice to remote start the vehicle.
+
if you programmed these buttons to = the Start / Stop button). The parking lights will flash 4
times. The siren or horn chirps 4 times. The vehicle is now no longer programmed to start
automatically.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
To Turn Off the Remote Start
To stop the engine that is running by remote start:
1. Press the
button twice on the remote transmitter in the Remote Start Mode.
2. Move the optional remote start enable toggle switch to the “OFF” position (if installed).
3. Press the brake pedal.
The vehicle will shut down and turn off the parking lights indicating the engine has stopped.
Shut-Down Input for Remote Starter
If any of the following conditions exist while the system is operating, the engine will not start or will
shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. Engine is over-revved (“Tachometer checking type” only).
4. The pre-programmed run time (5 / 10 / 20 / 30 minutes) has elapsed.
5. Press the
button twice on the remote transmitter under remote start mode.
6. Move the optional remote start enable toggle switch to the “OFF” position (if installed).
7. The vehicle refused to start running after 3 unsuccessful attempts.
(If Installed)
Disabling the Remote Start System
This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle
from being remote started accidentally. This feature is useful if the vehicle is being serviced or
stored in an enclosed area. To disable the remote start, move the optional remote start enable
toggle switch to the “OFF” position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmitter Battery Replacement
Regular Remote Transmitter:
If the range of your transmitter deteriorates, it is possible that the battery needs to be replaced.
1. Remove upper transmitter case.
2. Remove old battery.
3. Install two new CR2016 battery (3 volt), noting the (+) and (-) marks.
4. Replace upper transmitter case with care, trying not to damage the inside components.
2-Way LED Remote Transceiver:
When the power of the battery weakens, the remote will emit three short “Beep” sounds and the
LED symbol will flash for 5 seconds after pressing any button on the remote transmitter.
This will remind the user to replace the battery.
1. Remove the small phillips head screw from the bottom cover of the transceiver.
2. Remove lower transmitter case.
3. Remove old the battery.
4. Install a new CR2450 battery (3 volt), noting the (+) and (-) marks.
5. Replace lower transmitter case with care, don't damage the inside components.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACEMENT PARTS AND ACCESSORIES
TRANSMITTERS
DESCRIPTION
MODEL NO.
PRICE
2-Way LED Remote Transceiver
M8ARF-LED
$89.95 ea.
Remote Transmitter
M5ARF
$46.96 ea.
BATTERIES
DESCRIPTION
CR2450 - 3 Volt Lithium Battery
Replacements:
RadioShack: #CR2450
Duracell: #DL2450
Eveready: #ECR2450
Panasonic: #CR2450
CR2016 - 3 Volt Lithium Battery
Replacements:
RadioShack: #CR2016
Duracell: #DL2016
Eveready: #ECR2016
Panasonic: #CR2016
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND ACCESSORIES ORDER FORM
Mail to: Magnadyne Corporation
Credit Card or Money Order Only
(Sorry No Cash, C.O.D. or personal checks accepted)
Call: (310) 884-7777 Fax: (310) 637-9542
ATTN: Consumer Parts Sales
P.O. Box 5365
Carson, CA 90749-5365
SHIP TO: (No P.O. Boxes)
LAST NAME
FIRST NAME
INITIAL
STREET ADDRESS
ADDITIONAL ADDRESS
ADDITIONAL ADDRESS
CITY
STATE
ZIP CODE
DAY TIME PHONE NUMBER
CREDIT CARD INFORMATION
VISA
MC
CREDIT CARD N0.
CARD HOLDER’S LAST NAME
STREET ADDRESS
CITY
EXPIRATION DATE
FIRST NAME
INITIAL
STATE
QTY.
ZIP CODE
PART #
DESCRIPTION
PRICE EACH
TOTAL
Shipping and Handling
Sales Subtotal = ________ . ______
Up to $20.00
20.01 to 30.00
30.01 to 45.00
45.01 to 70.00
Over 70.01
$5.00
5.95
6.50
6.95
7.95
California Residents Add Sales Tax = ________ . ______
Shipping and Handling (See Chart) = ________ . ______
TOTAL = ________ . ______
On regular orders please allow 4-5 weeks for delivery.
Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED LIFETIME WARRANTY
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the
option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective
in materials or workmanship, when properly connected and operating on the correct power
requirements designated for the specific product. This warranty and Magnadyne Corporation or its
authorized agents obligations, hereunder do not apply where the product was: damaged while in the
possession of the consumer, subjected to unreasonable or unintended use, not reasonably maintained,
utilized in commercial or industrial operation, or serviced by anyone other than Magnadyne
Corporation or its authorized agent, or where the warning seal on the product is broken or the power
plugs or wires are detached from the unit. Magnadyne Corporation or any of its authorized agents do
not assume any labor costs for the removal and reinstallation of any product found to be defective, or
the cost of transportation to Magnadyne Corporation or its authorized agents. Such costs are the sole
responsibility of the purchaser.
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories used
in connection with the product resulting from improper installation, alteration, accident, misuse, abuse
or acts of nature.
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither the
siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness or
any accessory item are covered by our standard 12 month limited warranty.
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential or
incidental damages or claims that may arise due to failure of product to operate properly except
those accorded by law. Magnadyne's or its authorized agents liability to the repair, replacement of
the product as stated above if all conditions of the warranty are met. No expressed warranty or
implied warranty is given except those set forth herein. Magnadyne does not warrant or guarantee
against break in damage or the theft of the vehicle in part or whole, or against the loss or damage
to the contents of any vehicle in which a security system is installed. Magnadyne security systems
are only a deterrent against possible theft.
This warranty extends only to the original purchaser of the product and for the vehicle in which it was
originally installed. This warranty is not transferable or assignable to any person or vehicle. Defective
merchandise should be returned to the original point of purchase or secondly to Magnadyne
Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must be obtained
before sending, or merchandise may be refused.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
M8A-UM 12-18-03 Rev. A
© Copyright 2004 Magnadyne Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
|