Owner’s Manual
AVP2
Audio Video
Preamplifier
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Please read all instructions and precautions carefully and completely before operating your Proceed
component.
1. ALWAYS disconnect your entire system from the AC mains before connecting or disconnecting
any cables, or when cleaning any component.
2. This product is equipped with a three-conductor AC mains power cord which includes an earth
ground connection. To prevent shock hazard, all three connections must ALWAYS be used. If your
electrical outlets will not accept this type of plug, an adapter may be purchased. If an adapter is
necessary, be sure it is an approved type and is used properly, supplying an earth ground. If you
are not sure of the integrity of your home electrical system, contact a licensed electrician for assis-
tance.
3. ALWAYS keep electrical equipment out of the reach of children.
4. AC extension cords are not recommended for use with this product. If an extension cord must be
used, be sure it is an approved type and has sufficient current-carrying capacity to power this
product.
5. NEVER use flammable or combustible chemicals for cleaning audio components.
6. NEVER operate this product with any covers removed.
7. NEVER wet the inside of this product with any liquid.
8. NEVER pour or spill liquids directly onto this unit.
9. NEVER block air flow through ventilation slots or heatsinks.
10. NEVER bypass any fuse.
11. NEVER replace any fuse with a value or type other than those specified.
12. NEVER attempt to repair this product. If a problem occurs, contact your Proceed® dealer.
13. NEVER expose this product to extremely high or low temperatures.
14. NEVER operate this product in an explosive atmosphere.
15. ALWAYS unplug sensitive electronic equipment during lightning storms.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Maximizing the Value of Your Purchase..................................................... 7
send in that warranty card! ............................................................................... 7
Unpacking and Placement ........................................................................ 8
unpacking the audio video preamplifier......................................................... 8
remote control .................................................................................................... 8
placement .......................................................................................................... 8
ventilation............................................................................................................ 8
custom installations............................................................................................. 8
serial number ...................................................................................................... 9
register your purchase!....................................................................................... 9
Operating Voltage & Frequency ...............................................................10
warm up/break-in period ................................................................................ 10
A Word About Installation .......................................................................... 11
The Quickest Start: CD & DVD ....................................................................12
A Quick Start For CD ..................................................................................13
A Quick Start For DVD ............................................................................... 14
Special Design Features ............................................................................15
powerful hardware........................................................................................... 15
software updatable ......................................................................................... 15
multichannel ..................................................................................................... 15
Front Panel ..................................................................................................16
Viewing Simulcasts ............................................................................................17
tip: saving delay settings .......................................................................... 20
tip: saving input level settings ...................................................................21
Rear Panel ................................................................................................. 23
optional six channel input ........................................................................ 24
controlling remote zone volume...................................................................... 27
Building PHAST cables ............................................................................... 29
IR input tip polarity .................................................................................... 30
The Remote Control .................................................................................. 33
Using The Menu System ............................................................................ 35
to enter the menu system ................................................................................ 35
to exit the menu system ................................................................................... 36
to select a menu item ...................................................................................... 36
to change a menu item .................................................................................. 36
to save changes............................................................................................... 36
to “escape” or “cancel” without saving any changes.................................. 36
front panel equivalents .................................................................................... 36
The Operate Menu .................................................................................... 38
auto migration .................................................................................................. 38
migrating to analog .................................................................................. 39
forced/manual migration ......................................................................... 39
simulcast............................................................................................................ 39
setup: locked/unlocked .................................................................................. 40
display preferences .......................................................................................... 40
display position ................................................................................................. 40
on screen status................................................................................................ 40
status preferences..............................................................................................41
display timeout..................................................................................................41
display of text.....................................................................................................41
display background color ................................................................................41
volume preferences ......................................................................................... 42
4
Download from Www.Somanuals.com. All Manuals Search And Download.
volume display ................................................................................................. 42
volume speed .................................................................................................. 42
volume mute level ............................................................................................ 42
maximum volume ............................................................................................ 43
late night ........................................................................................................... 43
The Setup Menu......................................................................................... 44
define source buttons ...................................................................................... 45
example: setting up a cd transport ................................................................ 45
renaming source buttons................................................................................. 46
defining the input type .................................................................................... 46
setting audio delay .......................................................................................... 47
choosing a 2-channel mode .......................................................................... 47
multichannel THX .............................................................................................. 48
is it a recording device? .................................................................................. 48
how many input connectors? ......................................................................... 48
defining input connectors ............................................................................... 49
example: setting up a laserdisc player .......................................................... 49
defining the video connection ....................................................................... 50
defining multiple audio connections ............................................................. 50
setting & saving input levels .............................................................................51
set more buttons............................................................................................... 52
set speakers ...................................................................................................... 53
set configuration............................................................................................... 55
important note........................................................................................... 56
about your subwoofer: ............................................................................ 56
set distance ....................................................................................................... 57
set distance menu .................................................................................... 57
set levels ............................................................................................................ 58
set levels menu .......................................................................................... 58
bass level manager ......................................................................................... 59
bass level manager menu ....................................................................... 59
surround mode defaults................................................................................... 60
before you use surround mode defaults ................................................. 60
The Custom Menu ..................................................................................... 64
teach IR commands to your remote............................................................... 65
remote only menu ..................................................................................... 66
surround, path and more inputs menus .................................................. 67
misc control menus ................................................................................... 67
trigger settings .................................................................................................. 68
rear ir input menu ............................................................................................. 69
MP-8/9 Link........................................................................................................ 70
Link Master ........................................................................................................ 70
The About… Menu .....................................................................................71
Using the Special Menu ............................................................................ 72
special key actions menu ........................................................................ 72
sample status display screen ................................................................... 73
Using the AVP2 ............................................................................................74
setting the volume............................................................................................ 74
surround off ....................................................................................................... 74
THX Ultra® .......................................................................................................... 74
Dolby Digital ...................................................................................................... 75
Dolby Digital Surround EX................................................................................. 75
DTS...................................................................................................................... 75
DTS-ES Matrix ..................................................................................................... 76
DTS-ES Discrete .................................................................................................. 76
dolby pro logic ................................................................................................. 77
dolby pro logic II............................................................................................... 77
5
Download from Www.Somanuals.com. All Manuals Search And Download.
stereo surround ................................................................................................. 77
mono surround ................................................................................................. 77
mono on fronts ................................................................................................. 78
mono center only ............................................................................................. 78
automatic migration ........................................................................................ 78
forced/manual migration ................................................................................ 78
watching a simulcast ....................................................................................... 78
System Planning Guide............................................................................. 80
video placement ............................................................................................. 80
electronics placement..................................................................................... 80
speaker placement ......................................................................................... 80
additional notes on speaker placement.........................................................81
Your System Settings.................................................................................. 82
the about… menu ........................................................................................... 82
operate menu settings ..................................................................................... 82
vcr 1 button defaults......................................................................................... 83
disc 1 button defaults ....................................................................................... 83
vcr2/disc2 button defaults............................................................................... 83
tv/aux button defaults ..................................................................................... 84
satellite button defaults .................................................................................... 84
cd button defaults............................................................................................ 84
tape button defaults ........................................................................................ 85
aux button defaults .......................................................................................... 85
tuner button defaults........................................................................................ 85
more button defaults .................................................................................. 86-88
crossover settings.............................................................................................. 88
set distance ....................................................................................................... 88
set levels ............................................................................................................ 89
bass level manager ......................................................................................... 89
surround mode defaults.............................................................................. 89-90
control trigger 1................................................................................................. 90
control trigger 2 ................................................................................................ 90
rear ir in.............................................................................................................. 90
MP-8/9 Link........................................................................................................ 90
Link Master ........................................................................................................ 90
Troubleshooting ..........................................................................................91
Care and Maintenance ............................................................................ 93
U.S. and Canadian Warranty .................................................................... 94
90-day limited warranty ................................................................................... 94
five year extended warranty ........................................................................... 94
Obtaining Service ..................................................................................... 95
Specifications ............................................................................................ 96
Dimensions ................................................................................................ 97
Rack Mount Kit .......................................................................................... 98
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Maximizing the Value
of Your Purchase
Congratulations on choosing a superb product. Your Proceed Audio Video Pream-
plifier (AVP2) is designed to give you many years of outstanding performance,
and we are confident you will be happy with it.
We value our relationship with our customers, and often are in a position to help
you enjoy your home entertainment system even more—if we have some way of
contacting you.
send in that warranty card! Sending in your warranty card registers your product with us so that warranty
service in the U.S. and Canada (see the warranty policy at the end of this
manual) can be obtained easily and quickly even if you have lost your original
sales slip. (And how many of us are organized enough to retain all those sales
slips?) Moreover, for customers in the U.S. and Canada, sending in the card auto-
matically extends the warranty from 90 days to five years, at no cost to you.
Please send it in soon, before you forget.
But there are even more benefits to sending in your registration card:
✓ software update notices
✓ performance upgrade notices
7
We occasionally offer software updates to our products, providing new features
and control options. In the case of the Audio Video Preamplifier, these updates
are easily done without even opening up the unit, via flash-memory. If they in-
clude features you would like to have, you can get them—if you know about
them.
We also try to offer hardware-oriented performance upgrades and/or conversions
to make upgrading within a family of products as cost-effective as possible for
our customers. While not all upgrades can be inexpensive, we work to ensure
that they all represent excellent values to you—if you know about them.
So please, take a few minutes to fill out the warranty
registration card, and drop it in the mail.
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking and Placement
unpacking the Unpack your Audio Video Preamplifier and remove all accessories from the
audio video preamplifier carton.
Important!
Keep all packing materials for future transport of your Audio
Video Preamplifier. Shipping your new component in anything
other than its purpose-designed packing material may result
in damage that is not covered by the warranty.
remote control Your AVP2 includes a small remote control that covers the basics of turning the
unit on and off, selecting something to listen to or to watch, and adjusting vol-
ume. It is designed to make day-to-day operation of the system as simple as
possible.
Alternatively, you may decide that you would prefer to have a more powerful or
versatile remote control. Your dealer can assist you in selecting a learning remote
control that is appropriate to your needs, and can then teach the new remote
control all the necessary AVP2 commands from the AVP2 itself. The AVP2 can
transmit as well as receive IR commands, and its menu system contains an exten-
sive list of available commands for learning remote controls (going far beyond
what is normally available in such products).
8
placement Place the Audio Video Preamplifier near the digital sources, thus keeping inter-
connecting cables reasonably short. It may be placed on a shelf or in a cabinet
where it’s convenient to operate.
Note that adequate clearance for the AC cord and connecting
cables must be left behind the Audio Video Preamplifier. We suggest
leaving at least three inches of free space behind the Audio Video
Preamplifier to allow all cables sufficient room to bend without
crimping or undue strain.
ventilation It is normal and perfectly safe for your Audio Video Preamplifier to run warm. Be
sure to allow 2 to 3 inches of clearance above it to allow heat dissipation through
air circulation. The vents on both the bottom and the top of the Audio Video
Preamplifier must be kept free from any obstruction which would reduce the
flow of air through the unit. Avoid placement on soft surfaces that would restrict
airflow (such as carpeting).
custom installations Drawings are included in this manual to facilitate special installations and custom
cabinetry (see Dimensions). An optional, purpose-designed rack mount kit is
Download from Www.Somanuals.com. All Manuals Search And Download.
available for this product, drawings of which are also included at the end of this
manual (see Rack Mount Kit).
serial number The serial number for your Audio Video Preamplifier is found on the bottom of
the unit. Please note and record this number for your future reference.
register your purchase! Having found the serial number, now would be a good time to fill out the regis-
tration card. Please register your purchase so we can advise you of software up-
dates and other items of interest.
In the U.S. and Canada, registering your purchase also automatically ex-
tends your warranty from 90 days to five years. It will take only a minute
or so. Please complete the card now, before you forget.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Voltage
& Frequency
The Audio Video Preamplifier is set at the factory (internally) for 100V, 120V, 220V,
230V, or 240V and either 50 or 60 Hz AC mains operation, as appropriate for the
country in which it is to be sold. (230V/50Hz only in European Union countries,
in compliance with CE regulations.) Neither the voltage nor the line frequency
setting may be changed by the user.
Make sure that the label on the rear panel of the Audio Video Preamplifier (above
the AC input receptacle) indicates the correct AC operating voltage for your loca-
tion. Attempting to operate the Audio Video Preamplifier at an incorrect voltage
can damage the unit.
Warning:
Neither the voltage nor the line frequency settings of your
Audio Video Preamplifier may be changed by the user. There
are no user-serviceable parts within the unit. Please refer any
problems to an authorized Proceed service center.
If the AC mains voltage or frequency indicated on your Audio Video Preamplifier
is incorrect, please contact your local, authorized Proceed dealer or distributor.
10
The Audio Video Preamplifier can easily be powered by a normal 15-ampere AC
mains line. If other devices are also powered from the same AC line, their addi-
tional power consumption should be taken into account.
warm up/break-in period Although your Proceed Audio Video Preamplifier delivers outstanding perfor-
mance straight out of the box, you should expect to hear it continue to improve
as it reaches its normal operating temperatures and its various components
“break-in.” It has been our experience that the greatest changes occur within the
first 300 hours as the AVP2 reaches thermal equilibrium and the capacitors fully
form. After this initial break-in period, the performance of your new product
should remain quite consistent for years to come.
The only exception to this rule is if power is removed from the unit for an ex-
tended period of time, allowing it to cool down. Depending on the degree of
cooling involved, you should expect a brief warm-up period before the Audio
Video Preamplifier’s sound quality is at its best. Unless your Audio Video Pream-
plifier was allowed to become quite chilled, subsequent thermal re-stabilization
should not take long.
Download from Www.Somanuals.com. All Manuals Search And Download.
A Word About Installation
Every effort has been made to make the Proceed AVP2 simple and straightfor-
ward to install and use.
Still, we have no way to evaluate many other variables such as the size and shape
of your room, its acoustics, and the associated equipment you have chosen to use
with your AVP2. All of these factors influence the ultimate performance of your
system. Moreover, the AVP2 incorporates many system-specific adjustments which
enhance its performance with the widest possible range of associated compo-
nents.
For this reason, we strongly encourage you to have your
system installed and calibrated by your dealer, whose
experience, training, and specialized equipment can make a
profound difference in the final performance of the system.
The AVP2 features the ability to “remember” the carefully calibrated settings cho-
sen by your installer. You may adjust any or all of these settings to suit your taste
for a particular recording, either from the front panel or from the remote control.
When you want to return to the calibrated settings (which most accurately repro-
duce the widest variety of program material), simply press recall on the remote
control, or on the front panel. In this way, you can feel free to experiment a bit
without worrying about losing the “correct” settings.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The Quickest Start: CD & DVD
The AVP2 is an exciting system, and we understand that many owners will be
anxious to get it up and running as quickly as possible. What follows is not a
replacement for a complete setup of the system. Rather, it is provided so
you can get some music and movies playing as quickly as possible. It assumes
that your system is already set up in other respects (speakers connected to power
amps, etc.). Once done, please read up on how to do a complete setup and cali-
bration in order to get the most from your investment (or have your dealer/in-
staller do it for you).
We have shipped the AVP2 with two input buttons already pre-programmed for
the sources most likely to be found in an AVP2-based system: CD and DVD. Hav-
ing done this, all you have to do is hook them up to the right connectors and
press the button to get going.
This “quickest start” assumes that your CD transport has a coaxial (RCA) digital
output, and that your DVD player has both composite video output and a coaxial
(RCA) digital output. If not, proceed to the next sections, A Quick Start For CD
and A Quick Start For DVD.
1
MAKE THE PHYSICAL CONNECTIONS; TURN EVERYTHING ON
Connect the outputs of the AVP2 to your power amplifier(s), as indicated
(front, rear, center, sub); ensure that the main video output of the AVP2 is
connected to your television (so you can see the on screen menus). Once
this is done, turn on all the components involved (CD transport, AVP2, tele-
vision, amplifiers). Turn the amps on last—always a good habit with any
audio system.
12
2
3
CONNECT YOUR CD TRANSPORT TO DIGITAL INPUT #2 ON THE AVP2
Doing so will give you access to your CD transport via the CD button on
the AVP2.
CONNECT AN S/PDIF (RCA/COAXIAL) AUDIO OUTPUT FROM YOUR
DVD PLAYER TO DIGITAL INPUT #4, AND CONNECT THE COMPOSITE
OUTPUT OF YOUR DVD PLAYER TO THE “COMPOSITE 1” VIDEO INPUT ON
THE AVP2
You might also take the time to set the digital output of your DVD player to
“AC-3” instead of “PCM/Pro Logic.” It will still output PCM digital audio if
you play a CD, but setting it to “AC-3” allows it to give you the discrete mul-
tichannel digital AC-3 standard. The AVP2 will automatically sense the na-
ture of the signal it receives, and will switch accordingly.
We chose the composite output for the initial default simply because it is
the output on DVD players that you can always depend on. (Many DVD
players have a switch that chooses between either S-video or component—if
the switch happens to be in the wrong position, you would end up with no
picture at all.)
4
PRESS EITHER CD OR DISC 1AND START ENJOYING YOUR AVP2
Download from Www.Somanuals.com. All Manuals Search And Download.
A Quick Start For CD
There is a reasonable chance that either your CD transport or your DVD player
may have a different set of output connectors than what we have assumed it
might have in the “quickest start” section. In that case, setting up the AVP2 to take
advantage of your particular equipment is still quite simple, though it will require
a couple extra steps.
1
MAKE THE PHYSICAL CONNECTIONS; TURN EVERYTHING ON
Connect the outputs of the AVP2 to your power amplifier(s), as indicated
(front, rear, center, sub); connect a CD transport to any matching digital in-
put connector on the AVP2, noting which connector you use; ensure that
the main video output of the AVP2 is connected to your television (so you
can see the on screen menus). Once this is done, turn on all the compo-
nents involved (CD transport, AVP2, television, amplifiers). Turn the amps
on last (always a good habit with any audio system).
2
3
PRESS AND HOLD THE CD BUTTON ON THE FRONT OF THE AVP2
This shortcut of pressing and holding an input button will take you directly
to the define button menu for that button.
TELL THE AVP2 WHICH CONNECTOR YOU USED FOR YOUR CD
TRANSPORT IN STEP 1
13
We have no way of knowing what sort of digital interface your particular
CD transport might use (AES/EBU? RCA? BNC? EIA-J?), but logically, you’d like to
be able to use your main CD transport with the button labeled cd. This
step allows you to use whatever connector you need to use in conjunction
with the button you’d like to use.
Using the volume ± button on the remote (or the volume knob), move the
arrow cursor down to the line that reads “audio connectors” and press en-
ter (or mute on the front panel). Press volume – to move to 1: Digital 2 and
press enter (mute) again. Then move the arrow cursor down to the line that
defines which connector is being used, and press enter (mute) again. With
→
the cursor changed to an arrow within a diamond ( ) instead of an ar-
row, the volume ± buttons or the knob will allow you to select whatever
digital input connector you used in Step 1. When done, press enter (mute)
again to save your change.
4
PRESS MENU THREE TIMES TO EXIT THE MENU SYSTEM, AND ENJOY
Make sure the volume is on at a low level before you fire up your CD
player, press the cd button, and raise the volume to a comfortable level. Ac-
cording to the factory defaults (which you can easily change), cd is preset
to come on in 2-channel/surround off. You should properly calibrate the
system so all speakers are playing at the proper volumes before you listen
critically to multichannel audio. Performing this calibration only takes only a
few more minutes, but you should read up on it a bit first. You can enjoy
the AVP2 in regular stereo until then.
Download from Www.Somanuals.com. All Manuals Search And Download.
A Quick Start For DVD
We understand: you’re in a rush to hear Dolby Digital on your new system. Re-
member: What follows is not a replacement for a complete setup of the
system. We will assume here that you have already done the CD setup on the
previous page. To get a DVD player playing:
1
MAKE THE PHYSICAL CONNECTIONS
Noting which connectors you use, connect a digital output of your DVD to
any matching digital input on the AVP2, and a video output of your DVD to a
corresponding video input on the AVP2. Turn everything on.
2
3
PRESS AND HOLD THE DISC 1 BUTTON ON THE AVP2
This shortcut of pressing and holding an input button will take you directly
to the Define Button menu for that button, disc 1 in this case .
TELL THE SYSTEM WHICH CONNECTORS YOU USED FOR YOUR DVD
PLAYER IN STEP 1
Using the volume ± buttons (or the volume knob), move the arrow cursor
down to the line that defines your video connection and press enter (or
mute on the front panel). Make sure the AVP2 knows where you plugged
in your DVD player’s video output. Change the video: setting to the correct
video input, and press enter to save any changes you need to make.
14
Similarly, set up your audio connection: move the arrow cursor down
(volume ±) to the audio connectors line and press enter; move to the line
that reads 1: digital 3, and press enter again. Move down to the connector
line, press enter and with the cursor changed to an arrow within a diamond
→
(
), the volume ± buttons will allow you to select whatever digital input
you used when hooking up the system.
4
PRESS MENU A FEW TIMES TO EXIT THE MENU SYSTEM, AND ENJOY
Make sure the volume is on at a low level before you fire up your DVD
player; press the disc button once, and raise the volume to a moderate/
comfortable level. Important: you should properly calibrate the system so
all speakers are playing at the proper volumes before you listen critically to
multichannel audio. Performing this calibration only takes only a few more
minutes, but you should read up on it first. Please review the chapter on
The Setup Menu for more information, beginning on p. 44.
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Design Features
Congratulations on your purchase of the Proceed Audio Video Preamplifier
(AVP2). We have gone to great lengths to ensure that the AVP2 remains
“future-proof” even in these times of change. As a result, you will be able to en-
joy the outstanding performance of the Audio Video Preamplifier for many years.
In case you are interested in technical details, what follows is a brief outline of
some of the key technologies in your new product.
powerful hardware The AVP2 shares the same type of powerful DSP engine used in the Mark
Levinson Nº40 Media Console, employing multiple Analog Devices SHARC DSP
chips in a Madrigal-designed operating system. This DSP engine has sufficient
power to handle the decoding requirements of Dolby Digital, DTS, MPEG2, THX,
and many other decoding schemes. In addition, its power and flexibility provide
for future updates to handle as-yet-undefined digital audio standards that may be
adopted in the future, such as a secure digital interface for DVD-Audio or SACD
(should the recording industry ever manage to agree on such a thing).
The AVP2 includes eight channels of digital to analog conversion, all of which
can process and convert 192 kHz digital information. In addition, all volume con-
trols within the AVP2 are implemented in the analog domain, allowing the DACs
to run at their maximum resolution at all times. (This approach stands in contrast
to digital volume controls, which operate by requiring the converters to operate at
less than their maximum capabilities. After all, what would be the point of having
24 bit/192 kHz music formats if you end up throwing away much of the improve-
ment in a digital volume control?)
15
software updatable All the software that the AVP2 uses is stored in special “flash” memory that can
easily be updated as improvements are made available. These improvements can
affect both operational and performance enhancements, and can accommodate
new industry standards for digital audio (which seem to proliferate with every
passing every year).
With a simple software download a short time after such a new digital audio
standard is announced, your Audio Video Preamplifier would be able to decode
and play back the new digital signal. The previous generation of AVP, for example,
saw several significant software updates that provided support for both new sig-
nal formats and important feature enhancements.
multichannel The Audio Video Preamplifier is designed to be flexible with respect to its audio
configurations, as well. In its standard configuration, it provides the standard 5.1
channel selection of outputs made popular by home theater. However, it also in-
cludes an extra two channels that may be used in any of several ways, whether
to accommodate larger rooms (separate side and rear speakers) or more sophisti-
cated audio processing (Dual Drive™ surrounds, for example).
It is just a matter of what you want the system to do. You can have the system
work the way you want it to work, rather than being limited to the way we
thought you’d want it to work. (After all, a no-compromise, high performance au-
dio system should not be “one size fits all.”)
Download from Www.Somanuals.com. All Manuals Search And Download.
2
4
6
9
14 15 16 17 19
E
S
X
U
T
E
R
N
D
U
E
N
D
D
P
R
O
L
O
G
I
C
I
I
b a l a n c e
R
O
THX SURROUND EX
m a s te r
c e n te r
v c r
1
d i s c
1
v c r 2 / d i s c
2
t v / a u x
s a te l l i te
audio video
preamplifier
s u r ro u n d
c d
t a p e
a u x
t u n e r
m o re
s u r ro u n d m o d e
L A S E R
2 9 . 0
s u b
re c a l l
d e l a y
i n p u t l eve l
m u te
s t a n d by
p a t h
m a i n re m o te b o t h
d i s p l a y
i n te n s i t y
p owe r
PR O C E E D
1
3
5
7
8
10 11
12
13
18
Front Panel
1
STANDBY BUTTON AND INDICATOR
Pressing this button places the AVP2 in standby mode, turning off the dis-
play, disengaging all control functions, and turning off all outputs to the
main zone (remote zone functions remain available). The internal circuitry
remains on in order to maximize performance on demand, by virtue of all
circuits remaining thermally stable. Lest you think this wasteful, you should
know that the AVP2 draws about the same power as a light bulb, whether
in standby or fully on. The benefits of having it always warmed up and
ready to go (not to mention being able to respond to remote control com-
mands) far outweigh the small amount of power used. We recommend us-
ing the front panel power switch (13) only when you will be away from
your home for an extended period of time, such as during a vacation.
16
There is another good reason for using the AVP’s standby mode. The AVP2
will generate a full-frame, grey video signal during standby, rather than
passing no signal at all. This is particularly helpful with many CRT-based
projection televisions, since it gives them an ideal signal with which to
warm up. Turning on the projector 15-20 minutes before you begin your
movie, while leaving the AVP2 in standby, will allow your projector to look
its best right from the opening credits.
2
AUDIO/VIDEO SOURCES
These five buttons are generally used to select both the video and associ-
ated audio signals from any of the defined A/V inputs. (See define source
buttons in The Setup Menu section of this manual.) To use these Selection
Buttons, choose the appropriate path (see path, below). (For your music/
home theater room, “main” would be appropriate.) Then make your selec-
tion. The sophisticated switching system employed in the AVP2 allows si-
multaneous, independent routing of both audio and video signals the two
signal paths: main, and remote/record.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
AUDIO SOURCES
These four buttons are generally used to select audio signals from among
the defined audio-only inputs. (See define source buttons in The Setup
Menu section of this manual.) To use these selection buttons, choose the
appropriate path (see path, below), and then make your selection.
Viewing Simulcasts
The AVP2 has the ability to provide “simulcasts.” When this feature is turned
on, selecting any audio source after having selected a video source will
cause the newly-selected audio signal to “override” the audio portion of the
video selection (leaving the video signal unaffected). Thus, to enjoy a si-
mulcast, merely select the desired picture followed by the desired sound. To
revert to the regularly-used sound of the video input, just press the video
input button again. (Note that this “simulcast” feature can be turned on and
off in the Operate Menu, according to your personal preference. See The
Operate Menu, starting on p. 38.)
4
“MORE” SOURCES
With five A/V sources and four audio source buttons, most people will find
the AVP’s source selection capabilities more than adequate. However, the
AVP2 provides a maximum of fifteen audio inputs (eight analog pairs and
seven digital), in order to accommodate differing connection standards that
may be used on your source components. In addition, there are eight video
inputs available for use. Rather than allowing these extra connectors to re-
main unused after the initial nine primary source buttons are defined, we
have provided a more button to access additional, less frequently-used
sources.
To define additional sources that will be accessed by the more button, simply
use the menu system to define “more” sources: either a/v or audio-only. (See
set more buttons in The Setup Menu section of this manual.) You can teach a
learning remote control a direct-access command for any of these “extra”
sources, or use the more button to cycle through them.
17
5
PATH BUTTON AND INDICATORS
Pressing this button cycles among your various signal path options:
• main — the main room/home theater; this path determines
which video and audio sources are sent to the Main outputs on
the back of the AVP2. Sources selected for the main path are indi-
cated in yellow on the front panel LEDs.
• remote — determines which video and audio sources are sent to
the Record and Remote outputs on the back of the AVP2, to be
recorded or sent to another system elsewhere in the house. The
source selected on the remote path is indicated in red on its
front panel LED.
• both — the audio and video signals for both main and remote
paths may be selected at the same time, for your convenience; as
when entertaining, perhaps, for whole-house background music.
Any source selected for “both” main and remote paths will be
indicated by a green LED.
Tip:
To avoid any possibility of running into a “Tape Loop” conflict
(where the AVP2 prevents you from choosing what you want,
Download from Www.Somanuals.com. All Manuals Search And Download.
in order to protect the system from possible damage), simply
select a non-recording source on the record path.
6
SURROUND MODE
Pressing this button cycles among the various surround modes of the AVP2.
Note that the list of available surround modes is somewhat context-sensi-
tive, according to the signal being received.
For example: when you are playing a Dolby Digital 5.1 channel signal, you
are given only choices that make sense when playing such a signal (Dolby
Digital with and without THX); when listening to a “normal” stereo digital
signal such as you would get from a CD, you are presented with many
more options.
• THX Ultra — THX Ultra processing is used for movies which were
originally created for theatrical release; THX may be added to any
multichannel mode associated with movies (Dolby Digital/AC-3,
Dolby Pro Logic, Dolby Pro Logic II Movie, DTS, MPEG).
• Pro Logic — manually selecting Pro Logic may be needed when
listening to a conventional (PCM) digital signal, as from a
laserdisc player, which does not have an identifying “flag” to indi-
cate whether it is simply stereo, or Dolby Surround encoded. (In
the case of AC-3, DTS, or MPEG, the AVP2 will know positively
what sort of decoding is required and will provide it automati-
cally.)
• Pro Logic + THX — adds THX Ultra II post processing to the basic
Pro Logic decoding.
18
• Pro Logic II Movie — employs the more advanced Dolby Pro
Logic II algorithm for decoding Dolby-encoded movie
soundtracks. “DPL II” often yields sound that is surprisingly close
to a discrete multichannel signal such as Dolby Digital 5.1 from
older movies that lack the discrete multichannel soundtrack. (Note
that the soundtrack should be encoded as a “2.0 Dolby Surround”
signal for best results.)
• Pro Logic II + THX — adds THX Ultra II post-processing to Dolby
Pro Logic II Movie decoding.
• Pro Logic II Music— a somewhat different configuration of the
Pro Logic II algorithm which is optimized for use with ordinary
stereo music recordings (that are not specially encoded to the 2.0
Dolby Surround standard). This configuration often provides stun-
ning multichannel sound from ordinary stereo recordings.
• stereo surround — for enjoying two-channel stereo recordings
using all loudspeakers; this is an ambience extraction mode that
uses the natural ambience in the recording itself, rather than syn-
thesizing something artificial. The stereo surround mode tends to
be somewhat more subtle than Dolby Pro Logic II. Use it if the
PDL II Music mode seems a bit heavy-handed.
• mono surround — for monophonic recordings which would ben-
efit from some degree of additional ambience or spaciousness,
such as many classic movies and some sporting events.
• mono on center — a “true” mono, reproduced only through the
center channel speaker (and subwoofer, if you have one). Noisy
mono soundtracks often enjoy significant noise reduction by be-
ing reproduced in this mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
• mono on front — the same as mono on center, above, but the
sound is reproduced through all three front speakers.
• 2-ch/surround off — limits the system to two-channel stereo us-
ing only the Left and Right speakers (and subwoofer, if you have
one).
When decoding Dolby Digital™ 5.1-channel source material, clicking the
Surround mode button will toggle you between the two available Dolby
Digital modes:
• Dolby Digital: straight Dolby Digital decoding without further
processing.
• Dolby Digital + THX: the same as above, but with the additional
post-processing offered by THX 5.1; usually the best choice for
Dolby Digital-encoded movie soundtracks.
In addition, when decoding DTS™ source material, clicking the Surround
mode button will cycle you through the available DTS modes:
• DTS: straight DTS decoding without further processing
• DTS + THX: DTS decoding, plus the additional post-processing of-
fered by THX 5.1; usually the best choice for DTS-encoded move
soundtracks
7
8
DISPLAY INTENSITY
Pressing the display intensity button will cycle the AVP2’s display through
the four available levels of brightness: high, medium, low, and off. For ex-
ample, during bright daytime hours you may wish to use high; in the
evening, in a dimly-lit room, low is probably easier on the eyes.
19
RECALL
Pressing the recall button restores the AVP2 to its calibrated reference set-
tings for the relative output of all speakers. This is especially helpful after
having experimented with various settings of balance, center, rear, or sub,
or when comparing a modified surround default to “flat” balance, since one
touch of a button will restore your preamplifier to its original state (as de-
termined by the setup calibrations stored in memory; see System Setup &
Calibration and Using the AVP2 for more details).
9
MAIN DISPLAY
The main display provides information pertaining to the operation of the
AVP2 including selected source, surround mode, and volume levels. At all
volumes above a relatively quiet background level, and in all modes, the
volume control enjoys a resolution of 0.5 dB. Thus a change of 9.5 decibels
would be indicated by a change of 9.5 in the display.
Download from Www.Somanuals.com. All Manuals Search And Download.
The main display indicates the selected source and master volume by de-
fault, and can also display the following offsets when chosen: balance,
center, rear, sub. In addition, it can also display the input level (used in cali-
brating the input level to the analog to digital converter on analog sources
only) and the overall system (lip-sync) delay in milliseconds. Right- and
Left-facing arrows are provided to indicate the direction of the balance off-
set. Finally, the infrared receiver and transmitter for the remote control are
positioned on the left side of the main display.
10 DELAY
Pressing this button allows you to adjust (using the volume knob) the sys-
tem delay introduced to the audio, in milliseconds (mS). This delay is used
to restore the proper “lip sync” between the audio and video signals, espe-
cially when a video processor of some sort is being used to enhance the
picture.
The most common application of this is when displaying a “normal” inter-
laced video signal on a progressively-scanned digital television. The “line
doublers” or deinterlacers used always introduce a certain amount of video
delay while accumulating the information they need to display the video
progressively. Using the delay control, you can delay the audio until it
sounds in sync with the video again.
tip: saving delay settings
As a shortcut, you may save the current delay setting for the currently-se-
lected input by pressing and holding the delay button for a few seconds.
This serves as a shortcut to the menu item for the current input.
20
11
INPUT LEVEL
Pressing this button adjusts the input level of the selected signal to the ana-
log to digital converter. It may be used to compensate for variations in level
among sources. This adjustment is only important for analog sources (since
digital sources were effectively “level adjusted” when they were first con-
verted to digital).
If overload should occur, the AVP2 will indicate it by displaying ADC
CLIPPING on the screen (and “Clip!” in the main display). Pressing the input
level button followed by turning the volume knob counterclockwise will
reduce the input level by the number of decibels shown in the main dis-
play. Do so only until there is no indication of clipping, even during the
loudest passages.
You can also create a different, default input level setting for each analog
source defined in the menu system. If you can generate a 1 kHz, 0 dB ref-
erence signal in the source component (for example, a cassette tape record-
ing of a 1 kHz test tone, with the recording meters showing 0 dB), use this
signal to calibrate the input. With the volume of the AVP2 turned down,
play the 0 dB test tone, and adjust the input level until the display indicates
“Clip!” Reduce the input level setting a few decibels to allow for peaks
above 0 dB, and then press and hold the input level button to save the cur-
rent input level setting for the currently-selected input. (You may repeat this
procedure for each analog source.)
Download from Www.Somanuals.com. All Manuals Search And Download.
tip: saving input level settings
As a shortcut, you may save the current input level setting for the currently-
selected input by pressing and holding the input level button for a few sec-
onds. This serves as a shortcut to the menu item for the current input.
12 MUTE
Pressing the mute button will reduce the main output level of the preampli-
fier by a user-modifiable amount, ranging from 0.5 to 60 decibels. Pressing
the mute button a second time without adjusting the volume will return it
to its previous setting.
If you adjust the volume with either the front panel buttons or the remote
control while in the mute mode, the preamplifier will adjust its volume
from the muted volume and disengage the mute function.
The factory default setting of the mute circuit is -20 dB. (See Using the
AVP2 for information on changing the factory default setting.)
13 POWER BUTTON AND INDICATOR
Assuming that the Audio Video Preamplifier’s power cord is connected to
AC power, pressing this latching power button connects the AVP2 to the AC
mains and turns on the unit. When power is restored after an interruption,
the AVP2 will enter standby after a few moments’ delay to allow its circuits
to stabilize.
If AC power is being supplied to the Audio Video Preamplifier, the LED
above the power button is amber. Naturally, when AC power is discon-
nected, the LED is off.
21
14 MASTER
Normally, any adjustment made with the volume knob will be applied to all
loudspeakers equally, including Center, Rears, and Subwoofer(s), thus raising
or lowering the overall volume without changing the relative balance of the
various speakers. This is the default mode of operation for the volume con-
trol, to which the AVP2 automatically returns after you make other adjust-
ments (after a brief delay).
If you have changed the relative volume by adjusting balance, center, rear,
or subs, and wish to return more quickly to the normal master volume
control, pressing this button will override the usual delay and return you
immediately to master volume control operation.
15 BALANCE
Pressing this button followed by adjusting the volume knob will alter the
relative volume of the Front Left and Front Right speakers. The direction of
the perceived image shift is indicated by the arrowhead indicators in the
main display, as well as by the on screen display. When the balance is “cen-
tered” (favoring neither side over the other), the display will read
< – – EVEN – – >.
Turning the knob clockwise in the balance mode will shift the image to the
right; turning the knob counterclockwise will shift the image to the left.
Download from Www.Somanuals.com. All Manuals Search And Download.
16 CENTER
Pressing this button followed by adjusting the volume knob (or volume ±
on the remote control) will alter the volume of the Center speaker relative
to its normal, calibrated setting. The resulting offset will be indicated in the
main display, as well as by the on screen display, until the volume control
reverts to its normal, master mode.
As an example, increasing the center channel volume by three decibels
would result in a +3.0 being displayed until the volume control reverted to
normal operation, at which point the display would again indicate the over-
all volume setting.
17 SURROUND
Pressing this button once followed by adjusting the volume knob (or
volume ± on the remote control) will alter the relative volume of the sur-
round speakers relative to all others. The resulting offset will be indicated in
the main display, as well as by the on screen display.
If additional surround speakers are defined (either a single back center, or a
pair of back speakers), pressing this button a second time will allow you to
change the offset of the back channel(s).
18 SUB
Pressing this button followed by adjusting the volume knob (or volume ±
on the remote control) will alter the volume of the Subwoofer(s) relative to
all other speakers. The resulting offset will be indicated in the main display,
as well as by the on screen display, until the display returns to its normal,
master volume display.
22
19 VOLUME KNOB
This knob is used to make most adjustments on the AVP2. While the vol-
ume knob normally controls the master volume of the music/home theater
system (main path), it can be used in concert with other buttons to control
almost any aspect of system performance (as indicated above), and when
navigating the menu system from the front panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
1
2
3
4
a n a l o g i n p u t s
d i g i t a l i n p u t s
2 3
v i d e o
i n p u t s
1
2
3
4
5
6
7
8
1
R
L
L
L
1
2
1
2
1
2
5
6
7
8
3
3
3
R
R
m a i n
v i d e o
4
5
6
7
o u t p u t s
remote/record
a n a l o g o u t p u t s
re m o te
L
re co rd
video outputs
R
C
L
R
PUSH
L
C
S
L R
R R
A 1
L
L
R S -
2 32
t r i g g e r s
o u t p u t s
c o n t ro l p o r t s
P HA S T L i n k
™
c o m p a t i b l e
i r
i n p u t
2
1
2
1
2
1
2
1
2
3
1
1
2
3
3
3
3
R
A 2
R
R
d i g i t a l
o u t p u t
c
o
n
t
r
o
l
~
A
C
m
a
i
n
s
a u d i o v i d e o p re a m p l i f i e r
m a d e i n u. s. a.
by b
PR O C
E
E D
8
9
10
11 12
14
15
17
19
13
16
18
Rear Panel
Please remember to make a note of what sources you connect to which inputs.
You will need to set up the relationships between front panel buttons and rear
panel connectors later, in the setup menu.
23
For now, you can connect any source to any compatible connector—just keep a
list of what-goes-where. (Just such a list is waiting for you at the end of this
manual. You might want to photocopy it in order to keep the original clean for
future use.)
Caution!
Disconnect all associated equipment from the AC mains
BEFORE making any signal connections and applying power
to the Audio Video Preamplifier.
1
BALANCED ANALOG INPUT1
This input accepts right-channel and left-channel signals from source
equipment with balanced outputs.
The pin assignments of these XLR-type female input connectors are:
Pin 1: Signal ground
Pin 2: Signal + (non-inverting)
Pin 3: Signal – (inverting)
Connector ground lug: chassis ground
These pin assignments are consistent with the standards adopted by the
Audio Engineering Society. Refer to the operating manuals of your bal-
anced-output line-level sources to verify that the pin assignments of their
Download from Www.Somanuals.com. All Manuals Search And Download.
output connectors correspond to the AVP2. If not, wire the cables so that
the appropriate output pin connects to the equivalent input pin.
Connect the right-channel and left-channel balanced outputs of your source
components to the corresponding balanced inputs on the AVP2.
• Note: If you do not have balanced sources and need another
single-ended input, it is possible to fabricate a cable to connect
line-level sources with single-ended output to these balanced in-
puts:
1
2
3
22-gauge
bus wire
Male RCA
(connect to source)
Male XLR
(connect to AVP)
2
SINGLE-ENDED ANALOG INPUTS 2-5 AND 6-8
These inputs normally accept right-channel and left-channel audio signals
from source equipment with single-ended (RCA) outputs. Single-ended au-
dio inputs are provided for a total of seven components. Note that the
video portion of the signal from any video source (VCR, laserdisc, TV)
would be connected on the right side of the rear panel, in the Video Input
section. (See below.)
Connect the right-channel and left-channel single-ended outputs of your
various source components to the corresponding inputs on the AVP2.
24
optional six channel input
If you have the “AVP2 Plus,” then inputs 6-8 may be “ganged together” to
form a single, high quality, six-channel input for DVD-Audio or SACD. Sig-
nificantly, all of the AVP2’s powerful bass management options remain avail-
able for this multichannel analog input.
3
AES/EBU DIGITAL INPUT1
Digital Input 1 accepts digital audio in the professional 110Ω AES/EBU digital
interface standard (via a cable equipped with XLR-type connectors) from a
digital satellite receiver, compact disc, laserdisc, DVD or other digital source
component. Connect the AES/EBU digital output of your source component
to the AES/EBU input of the AVP2 using a high quality 110Ω AES/EBU cable
such as Madrigal MDC-1.
The pin assignments of these AES/EBU XLR-type female input connectors are:
PUSH
Pin 1: Shield
Pin 2: Digital + (non-inverting)
Pin 3: Digital – (inverting)
2
1
3
Connector ground lug: chassis ground
These pin assignments are consistent with the standards adopted by the
Audio Engineering Society and the European Broadcast Union. Refer to the
operating manuals of your digital sources to verify that the pin assignments
of their output connectors correspond to the Audio Video Preamplifier. If
not, wire the cables so that the appropriate output pin connects to the
equivalent input pin.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
S/PDIF (ON RCA) DIGITAL INPUTS 2-5
Digital Inputs 2-5 accept digital audio conforming to the 75Ω S/PDIF digital
interface standard (via 75Ω cables equipped with RCA-type connectors)
from a digital satellite receiver, compact disc, laserdisc, DVD or other digital
source component. Connect the 75Ω S/PDIF output of your source compo-
nent to either of this input of the AVP2, using a high quality 75Ω cable
such as Madrigal MDC-2.
If you have the optional internal RF demodulator installed in your Audio
Video Preamplifier, Digital Input 3 is dedicated to that RF connection and
can only be used for that purpose. Connect the RF (Dolby Digital/AC-3)
output from your laserdisc player to Digital Input 3 if you have the internal
RF demodulator installed.
5
S/PDIF (ON BNC) DIGITAL INPUT 6
Digital Input 6 accepts digital audio conforming to the 75Ω S/PDIF digital in-
terface standard (via 75Ω cables equipped with BNC-type connectors) from
a digital satellite receiver, compact disc, laserdisc, DVD or other digital
source component. Connect the 75Ω S/PDIF output of your source compo-
nent to either of these inputs of the Audio Video Preamplifier, using a high
quality 75Ω cable such as Madrigal MDC-2.
6
7
EIAJ OPTICAL DIGITAL INPUT 7
Digital Input 7 accepts digital audio in the EIAJ optical (sometimes called
“Toslink™”) digital interface standard from a digital satellite receiver, com-
pact disc, laserdisc, DVD or other digital source component. Connect the
EIAJ digital output of your source component to the EIAJ input of the Audio
Video Preamplifier using a high quality EIAJ optical cable.
25
VIDEO INPUTS
The AVP2 includes four composite and four S-video inputs. Any combina-
tion of the available inputs may be used, and for your convenience, conver-
sion from S-video to composite is provided on both the main and the
record/remote paths.
Thus S-video sources may be viewed via either the S-video or the compos-
ite outputs; composite sources are only available on the composite output.
(If viewed via the S-video output, the composite signal will be in black and
white.)
Composite video inputs use RCA connectors. S-video inputs utilize “S” con-
nectors:
S-video connector
Connect the video outputs of your video components to appropriate video
inputs on the AVP2. (See The Setup Menu for more information on pro-
gramming your input buttons for either composite or S-video use.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Note:
S-video (Y/C) signals are more susceptible to degradation
over long wire runs. The quality of wire used makes a
significant difference, but regardless, it is generally
inadvisable to run S-video cables more than twenty feet (6
meters). Composite video signals tend to hold up better over
longer runs, especially when high quality 75Ω cable such as
Madrigal MDC-2 is used.
8
BALANCED MAIN OUTPUTS (L, C, R)
The pin assignments of these XLR-type male outputs conform to the inter-
national AES standard, and are as follows:
Pin 1: Signal ground
Pin 2: Signal + (non-inverting)
Pin 3: Signal – (inverting)
1
2
3
Connector ground lug: chassis ground
Refer to your power amplifier’s operating manual to verify that the pin as-
signments of its input connectors correspond to the Audio Video Preampli-
fier. If not, wire the cable so that the appropriate output pin connects to the
equivalent input pin, or reverse the leads of both your speaker cables to “re-
verse the reversal” and restore correct polarity.
High quality single-ended outputs are also provided for compatibility with
power amplifiers lacking balanced inputs.
26
Connect the left-front, center and right-front outputs of the Audio Video
Preamplifier to the corresponding inputs on your power amplifier(s).
9
SINGLE-ENDED MAIN OUTPUTS (ALL CHANNELS)
The first six of these eight RCA connectors provide the main 5.1 channels
normally associated with a high quality multichannel system: the left-front,
center and right-front outputs of the AVP2 are duplicated here in single-
ended form (for compatibility with power amplifiers lacking any balanced
input capabilities), along with the left-surround, right-surround and
subwoofer channels. Connect these outputs to the corresponding power
amplifier channels.
In addition, two “auxiliary” output channels are provided, labelled aux 1
and aux 2. These channels are used for any of several applications such as
support for 7.1 channel systems (using either separate side and rear chan-
nels Dual Drive™ surrounds), or as additional subwoofer channels. Select
the best use for your particular system in the Setup Menu, according to
your speaker configuration.
10 REMOTE ZONE OUTPUTS
The AVP2 includes a second signal path (beyond the primary one used in
the main listening room) that can feed a remote zone, or a record path for
making recordings, or both. There is one limitation: the remote and record
outputs always contain the same signal.
Download from Www.Somanuals.com. All Manuals Search And Download.
Thus you can watch one program while recording another; or watch one
program while sending a different one to another part of the house; or you
can watch what is being recorded from either another part of the house or
from within the main room. But there is a limit: you cannot have three in-
dependent programs running simultaneously on the main, remote and
record paths, because the remote and record paths always share a single
source.
The main difference between the remote output and the record outputs is
that the remote outputs include a high quality analog volume control; the
record path remains at a fixed, line level at all times.
The AVP2 can distribute either analog or digital sources to a remote zone
or recording devices without your having to think about the details of
whether the signal originates from an analog or a digital source. Multichan-
nel signals automatically will be downmixed to two analog channels for
use in the remote zone; if you have a second home theater in the house,
you can even use the AVP2’s digital output to forward the original multi-
channel digital signal to that remote home theater “zone.”
controlling remote
zone volume
The volume of the remote zone is controlled by selecting the remote path on
the front panel and then adjusting volume conventionally, using the knob; al-
ternatively, it may be adjusted by simply sending an infrared volume command
to the rear panel ir input, when that input is configured to receive only re-
mote zone signals.
If you are using a remote zone, connect either the balanced (preferred, espe-
cially for long runs of cable) or the single-ended remote outputs to the ampli-
fier serving your remote zone.
27
11
RECORD OUTPUTS
The AVP2 includes a second signal path (beyond the primary one used in
the main listening room) that can feed a remote zone, or a record path for
making recordings, or both. There is one limitation: the remote and record
outputs always contain the same signal.
Thus you can watch one program while recording another; or watch one
program while sending a different one to another part of the house; or you
can watch what is being recorded from either another part of the house or
from within the main room. But there is a limit: you cannot have three in-
dependent programs running simultaneously on the main, remote and
record paths, because the remote and record paths always share a single
source.
The main difference between the remote output and the record outputs is
that the remote outputs include a high quality analog volume control; the
record path remains at a fixed, line level at all times.
The AVP2 can distribute either analog or digital sources to a remote zone
or recording devices without your having to think about the details of
whether the signal originates from an analog or a digital source. Multichan-
nel signals automatically will be downmixed to two analog channels for
use in the remote zone; if you have a digital recorder such as a DVD-RW,
you can even use the AVP2’s digital output to copy the original multichan-
nel digital signal to your recorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you wish to make recordings to a recording device such as a cassette deck
or VCR, connect the record outputs to the record inputs of that device. Be
sure to tell the AVP2 that the device is capable of recording in the define
buttons menu, within the setup menu, during initial setup of the system. (See
The Setup Menu.)
12 DIGITAL OUTPUT
The (S/PDIF on an RCA) digital output allows you to distribute a digital source
in its original, unprocessed digital form. For example, if you had another
multichannel system elsewhere in the home, you could forward a Dolby
Digital bitstream to the other system from this one—running a single digital
cable instead of five or six analog cables for surround sound applications.
Alternatively, you could use this digital output to make digital recordings.
Note that this output will not contravene any copy protection systems, and
you should only make copies of recordings for which you have legal rights
to do so. (You always read the FBI warning at the beginning of movies,
right?)
The digital output always tracks whatever source is selected in on the main
path (as opposed to the remote/record path).
13 REAR PANEL ACCESS DOOR
This small, removable panel is reserved for possible future applications as
hardware standards evolve.
28
14 PHASTLink™ CONTROL PORTS
These two communications ports provide for sophisticated inter-component
communications between the AVP2 and certain compatible Proceed prod-
ucts. To access the built-in intelligence of these communications capabilities,
simply “daisy chain” your various PHAST™-capable Proceed components
together using eight conductor “straight-through” cables with RJ-45 connec-
tors at both ends. You can buy these cables from your dealer as an acces-
sory item.
Thus, if the only other Proceed PHAST-compatible component you have is
the Five Channel Amplifier, you should connect one of the AVP’s comm
ports to the power amplifier’s comm port using a “straight-through” RJ-45
cable. If there are additional Proceed PHAST-compatible components in the
system, daisy chain them in a similar way, going from comm port to comm
port.
The RJ-45 cable needed for the connection between the AVP2 and other
PHAST-compatible Proceed components may be purchased from your Pro-
ceed dealer. It may also be easily and inexpensively made to length using
two RJ-45 connectors and the appropriate length (up to 100 feet/30 meters)
of RJ-45 (flat, eight conductor) cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
RJ-45 cables and connectors are used throughout the world for both tele-
communications and computers, and are widely available at low cost. The
connectors are crimped on to the ends of the cable such that pin 1 at one
end is connected to pin 1 at the other end. Such a “straight-through” con-
nection is (counter-intuitively) made by introducing a 180° twist in the
cable between the two ends, as shown below.
Building PHAST cables
To PHASTLink compatible component
To AVP
Locking tab
Locking tab
Connecting the communication ports other than as
described in this manual may damage the AVP2 and the
associated components, and will void those products’
warranties.
These ports also provide for extensive home automation flexibility via the
PHAST™ protocols, should you be interested in integrating other brands of
products into the system in a more comprehensive control system. Your
dealer can assist you in taking advantage of these advanced features.
15 RS-232 PORT
29
The AVP2 also includes an RS-232 port, which may be used in conjunction
with external control systems such as Audioaccess, AMX, or Crestron. Your
dealer can assist you in taking advantage of these advanced features.
This RS-232 port may also be used to update the operating software of the
AVP2, so that your system will be able to handle new digital audio formats
as they are introduced. (Think of updating the software in the AVP2 as be-
ing like installing new software in your computer… only much less pain-
ful.) Once again, your dealer can assist you in taking advantage of these
advanced features, should the need arise.
The “pinout” connections used on the RJ-11 connector used for the RS-232
port is as follows:
R S -
2 32
t r i g g e r s
o u t p u t s
c o n t ro l p o r t s
RS-232 pin configuration:
pin 2 = Rx from PC
pin 3 = Tx to PC
P HA S T L i n k ™ c o m p a t i b l e
i r
i n p u t
1
2
1
2
3
4
5
6
pin 5 = ground
c
o
n
t
r
o
l
Note that only qualified technicians should attempt to make use of the spe-
cial capabilities afforded by this communications port.
Download from Www.Somanuals.com. All Manuals Search And Download.
16 IR INPUT
A 1⁄8" “mini” jack labeled ir input near the lower right corner of the rear
panel provides direct access to the infrared control circuitry of the AVP2. It
may be configured during setup (in an on screen menu) to interpret in-
coming signals in either of two ways:
• Remote: when in Remote mode, the AVP2 will interpret any com-
mand entering through the remote IR jack as being intended to
affect the record/remote path only. This feature allows easy ac-
cess to all sources connected to the AVP2 from elsewhere in the
house with the addition of any commercially-available IR repeater.
• Local: when in the Local mode the remote IR jack responds to
all commands, as the infrared receiver in the main display of the
front panel would. This mode is most often used with an IR re-
peater when the AVP2 and other components are placed inside
of cabinets (preventing the normal IR receiver from receiving re-
mote commands). (See The Setup Menu.)
The incoming signal for the remote IR input should conform to widely-ac-
cepted IR repeater standards: that is, the signal present should be between
3-15 volts DC at less than 100 mA current, with a positive tip polarity, as
shown below:
IR input tip polarity
– +
5-12 volts @ less
than 100 mA
30
Your Proceed dealer can help you take advantage of these design features
to maximize your system’s versatility.
17 DC TRIGGERS
Each of the two remote on/off triggers can be configured by your installer
to provide either 5V or 12V DC trigger signals, either in response to the
AVP2 coming out of standby into operate, or in response to an indepen-
dent IR command. The tip polarity for each of these triggers is as shown
below:
– +
5-12 volts @ less
than 100 mA
These triggers provide some degree of control and automation over prod-
ucts that lack more sophisticated communications capabilities. For example,
you could have one of these triggers toggle your amplifier(s) on and off ac-
cording to the operational status of the AVP2, while the other served to lower
the screen for your projection television when a particular IR command was
received.
By default, these triggers are programmed to provide 12V “level” signals that
are tied to the state of the AVP2: 12V when operational, and 0V when in
standby.
Download from Www.Somanuals.com. All Manuals Search And Download.
18 VIDEO OUTPUTS
The AVP2 includes a total of four composite video outputs and two S-video
outputs. One of each is used for the main outputs to your display device;
the rest are available for either remote zone or recording applications. Any
combination of the available outputs may be used.
For your convenience, conversion from S-video to composite is provided on
both the main and the record/remote paths. Thus S-video sources may be
viewed via either the S-video or the composite outputs; composite sources
are only available on the composite output. (They will display in black and
white on the S-video output.)
Composite video outputs use RCA connectors. S-video outputs utilize “S”
connectors:
S-video connector
The main output (either or both composite and S-video, depending on
what you need to use) should be connected to your video monitor in the
main home theater system.
The record/remote outputs can be used to feed video signals to another
system elsewhere in the house, or for making recordings on VCRs, much as
you would make audio cassette recordings with a traditional preamplifier or
receiver. Connect them to the corresponding inputs on the back of those
video tape recorders.
Installation Note:
S-video (Y/C) signals are more susceptible to degradation
over long wire runs. The quality of wire used makes a
significant difference, but regardless, it is generally
inadvisable to run S-video cables more than twenty feet (6
meters). Composite video signals hold up better over longer
runs, especially when high quality 75Ω cable such as
Madrigal MDC-2 is used. Therefore we strongly suggest you
use a composite to run video to a remote zone, and save the
S-video output for a local S-capable VCR.
31
19 ~AC MAINS INPUT
The latching AC power switch on the front panel disconnects the AVP2
from the wall outlet’s AC power. Check to ensure that the power switch is
disengaged (protruding from the front panel), then plug the supplied three-
prong power cord into the AC mains receptacle before plugging the power
cord into the wall. (If a longer AC power cord is required for your applica-
tion, be sure to use a three-conductor power cord which conforms to IEC
standards.) Once the connections are all firmly made, switch on power at
the front panel. After a few moments to initialize, the AVP2 will be ready for
use.
The AVP2 is designed to be left in Standby when not in use, rather than
completely “off.” Being in Standby allows it to respond to commands from
the remote control and maintains a stable operating temperature at all
times for optimal performance and longevity.
Download from Www.Somanuals.com. All Manuals Search And Download.
The Proceed AVP2 has been safety-tested and is designed
for operation with a three-conductor power cord. Do not
defeat the “third pin” or earth ground of the AC power cord.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
special
surround
standby
volume
+
+
–
–
video
menu
audio
enter
mute
R
PR O C
E
E
D
Madrigal Audio Laboratories, Inc.
The Remote Control
The AVP2 itself is capable of teaching sophisticated learning remote controls a
wide range of highly specialized functions, if you feel you need such capabilities.
For example, if you want to create infrared macros commands (a series of com-
mands that will be transmitted, one after another, at the touch of a single button),
we suggest you purchase an appropriate macro-capable remote control from any
of a number of companies that specialize in such products, and then teach it the
commands you need from the AVP2 itself.
The AVP2 contains many highly specialized commands designed to simplify cus-
tom, home-automation installations. Including all of these commands in the stan-
dard remote control would have resulted in an excessively complex, intimidating
remote that many people would find too complicated.
33
By contrast, the standard remote control supplied with the AVP2 is small and
simple, yet it allows you to control all routine operations from the comfort of
your chair. These include source selection, volume adjustment, surround modes,
menu navigation and standby/operate switching.
The buttons on the standard remote control provide for these functions:
special: displays and executes a list of special functions, any of which you might
want to be able to control from your chair. By pressing and holding the special
button, you can have the AVP2 display this list on the screen. Once displayed, you
can use the volume ± button to move the cursor up or down the list to the item
you want to control. Press enter to toggle the value and leave the list, or press
special again to simply leave the list. From then on, simply pressing the special
button toggles the last-selected function on the “special” list. For more informa-
tion, please refer to Using the Special Menu, starting on page 72.
surround: allows you to cycle among whatever surround modes are appropriate to
the signal being received. For example, you would not be allowed to decode
Dolby Digital with the DTS algorithm (nor would you want to try!); but you
would be allowed to toggle THX on and off, and you would have several options
for a plain two channel signal, including Dolby Pro Logic II Music and Stereo Sur-
round for music, and Pro Logic II (with or without THX) for movies.
standby: toggles the AVP2 in and out of standby.
Download from Www.Somanuals.com. All Manuals Search And Download.
video: cycles among the defined audio/video sources from the first to the last,
returning to the first. If you have A/V buttons that are defined as “unused” in
their Define Button menus, they will be omitted from the list of A/V sources ac-
cessed by this button. Since this button acts as a rocker switch, you can move
either forward or backward within the list of defined A/V sources.
audio: cycles among the defined audio-only sources from the first to the last, re-
turning to the first. If you have audio buttons that are defined as “unused” in
their Define Button menus, they will be omitted from the list of audio sources
this button accesses. Since this button acts as a rocker switch, you can move ei-
ther forward or backward within the list of defined audio sources.
volume: this button normally adjusts the overall system volume up or down, al-
though it is also used in conjunction with other buttons and/or menu items to
vary most of the available system adjustments. When navigating within the on-
screen menu system, the volume ± button will either:
• move the cursor up or down
[when the “select-it” cursor (✓) is displayed]
• increment/decrement the value of a selected menu item
→
[when the “change-it” cursor ( ) is displayed]
menu: when the on screen menu is not displayed, pressing this button will bring
up the main menu. Once in the menu system, pressing menu will exit your current
level without making any permanent changes, returning you to the next-higher level.
Repeated pushes of menu will ultimately take you out of the menu system entirely
(e.g., will exit the topmost level of the menu system, taking you out of the menus en-
tirely).
34
enter: when navigating through the on-screen menus, the enter button serves two
purposes: indicating that something is to be changed, and then confirming the
change. When the “select-it” cursor (✓) is pointing to an item that has a sub-menu,
pressing enter will take you to that sub-menu. Otherwise, pressing enter will change
→
the “select-it” cursor (✓) to the “change-it” cursor ( ) so the menu item may
be changed directly. (At this point, using the volume ± buttons will change the
value of the item in question.) Either way, pressing enter after changing a value
confirms the change.
mute: pressing this button duplicates the function of the mute button on the
front panel, reducing the volume of the main system by a user-selectable amount
when the main path is selected; when the remote path has been selected, it will
mute the remote outputs only, by the same user-selectable amount.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using The Menu System
The AVP2 uses a dynamically-updated menu system that operates more intelli-
gently than most such systems. For example, when configuring inputs, the menu
options change according to the selections you have already made. In effect, the
AVP2 only asks you for relevant information, thereby minimizing confusion.
Four buttons on the remote control are used to navigate through its extensive on
screen menu system: menu, enter, volume +, volume –.
You may also navigate the menus from the front panel. The volume knob on the
may be used interchangeably with the volume ± buttons on the remote. If you
are more comfortable navigating the menu from the front panel, pressing and
holding recall will get you into the menu system (much as pressing menu would
from the remote); once in the menu system, recall continues to serve as menu
would (though you no longer have to press and hold it). Finally, while in the
menu system, pressing mute on the front panel has the same effect as pressing
enter on the remote. Thus:
• volume ± = volume knob
• menu
=
recall (must press and hold to enter menu system)
• enter
=
mute
For clarity’s sake, in most of the rest of the manual will refer to the labelled re-
mote control commands only, rather than always making awkward references to
menu (recall) or similar constructions. Just remember that you can use the
menus just as easily from the front panel as from the remote control.
35
to enter the menu system Pressing menu once will display the AVP2 Main Menu of the on screen menu
system. Note that the front panel display of the AVP2 shows –SETUP MENU– when
you enter the on screen menu system (to encourage you to look on screen,
where the important information is). The main menu provides access to the three
major function areas of the menu system:
• The Operate Menu is where user preferences are set. These items
tailor the way the system interacts with you to suit your personal
preferences, but do not effect the actual performance of the system
in any substantive way.
• The Setup Menu is normally used only by the installer at the time
of the initial system setup. Many of the items in this menu have
significant impact on the actual performance and functionality of
the system, and should be changed only by those who have taken
the time to learn the way the system works. (Reading this manual
should do the trick.)
• The Custom Menu is also used by your installer to customize your
system even further. Whereas every system must be properly setup
using the Setup Menu, the items in the Custom Menu are more
rarely needed—primarily in systems that employ home automation.
Once again, the items contained within this menu should be used
and/or changed only by those who have taken the time to learn
the way the system works (which you can do by reading this
manual thoroughly, if you wish).
• The About… menu describes the various parts of the operating
Download from Www.Somanuals.com. All Manuals Search And Download.
software being used by the AVP2, and is used only as a reference
should you ever need to call for technical support. You might want
to copy these (somewhat arcane) numbers down in the Your Set-
tings section of this manual for future reference.
to exit the menu system From the AVP2 Main Menu, pressing menu again will exit the menu system. Since
pressing menu (once within the menu system) also cancels current actions and
moves you up one level in the menu hierarchy, you can leave the menu system
by pressing menu repeatedly—no matter where you are within the system.
to select a menu item Once within the menu system, an arrow (✓) indicates the currently-selected item
on the menu. This arrow can be thought of as the “select-it” cursor. It can be
moved up or down with the volume knob or volume ± buttons on the remote
control.
to change a menu item Having selected the item you wish to work with, pressing enter will allow you to
work with it.
When changing the item in question can be displayed on the current menu
screen, the “select-it” arrow cursor changes to a “change-it” cursor: an arrow
→
within a diamond ( ). When the “change-it” cursor is displayed next to an item,
using the volume knob or volume ± buttons on the remote control will now in-
crement or decrement the value of the item in question.
Some of the changes called for by a particular menu item require more space
than is available at the end of the current line. In this case, pressing enter still al-
lows you to work with the item in question, by taking you to the next-lower
screen in the hierarchy. A case in point: there are several display preferences you
can modify to suit your needs; pressing enter when the cursor is next to display
preferences takes you to another screen that describes them in more detail.
36
to save changes Having changed/edited an item, you can save your changes by pressing enter
again. This both saves the change and returns you to where you were just prior
to making the change (either changing back to the “select-it” cursor or moving up
one level to the previous menu, as appropriate).
to “escape” or “cancel” If you wish to cancel any changes you might have made, exiting the currently-
without saving any changes modifiable menu item without saving any changes, simply press menu. This acts
like the Escape key or Cancel button on a computer, and will return you to
where you were just prior to making the change you decided not to save.
front panel equivalents In a pinch, you may need to navigate the menu system as outlined above, but
without using the remote control. (An example would be when teaching a learn-
ing remote commands, since it might learn the command being sent from the
AVP2 remote rather than the intended one.)
As described earlier, you can do this by pressing and holding the recall button
on the front panel for about three seconds; this serves as a front panel equivalent
of menu on the remote. Once in the menu system, the recall button on the front
panel can be clicked (without holding it each time), and the menu will respond
as though the menu button had been pushed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Once in the menu system, the front panel equivalents are:
• menu
• enter
• volume ±
= recall
= mute
= volume knob
(to cancel an action, or move up a level)
(to save a change and/or move up a level)
(to move up or down in a menu, or in-
crease/decrease a value)
As with the menu button on the remote control, clicking recall on the front
panel when the main menu is displayed will exit the menu system.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN MENU
OPERATE
SETUP
CUSTOM
ABOUT...
OPERATE
DISPLAY PREFERENCES
VOLUME PREFERENCES
AUTO MIGRATION: VISIBLE
SIMULCAST: OFF
DISPLAY PREFERENCES
DISPLAY POSITION
SET DISPLAY POSITION
ON SCREEN STATUS: YES
STATUS PREFERENCES
TIMEOUT: 3 SECONDS
CHARACTERS: NORMAL
BACKGROUND COLOR: BLUE
SETUP: UNLOCKED
→ DISPLAY
←
VOLUME PREFERENCES
→ DISPLAY: ABSOLUTE
SPEED: FAST
STATUS PREFERENCES
MUTE LEVEL: -20.0
MAX VOLUME: 91.0
LATE NIGHT: HIGH
- REFERENCE LEVEL 70.0 -
SOURCE INFO: ON
SIGNAL INFO: ON
MODE INFO: ON
RATE INFO: ON
SUB INFO: ON
VOLUME INFO: ON
↓ MIGRATION INFO: ON
RECORD INFO: ON
The Operate Menu
38
The operate menu and its sub-menus give you control over the way the system
displays information; over the details of how volume-related functions are
handled; and a couple other details pertaining to how you would like the system
to work.
OPERATE
DISPLAY PREFERENCES
VOLUME PREFERENCES
AUTO MIGRATION: VISIBLE
SIMULCAST: OFF
It also allows you to lock the setup settings (preventing access to the Setup and
Custom Menus) to minimize the chance of unwanted tampering with settings
that alter the way the system performs. By contrast, the operate menu provides
access to preferential settings that change the behavior, not the performance, of
the system.
SETUP: UNLOCKED
Before continuing on to the two major submenus of the operate menu, let’s take
care of the items on the menu itself that can be changed without having to ac-
cess submenus.
auto migration The AVP2 allows multiple connectors to be associated with a single input button
on the front panel, often simplifying the use of components such as laserdisc
players that may need as many as three different types of connection in order to
work reliably with all discs. During setup, you (or your installer) establish which
connectors should be associated with which buttons; and where multiple con-
nections are used, what priority should be given to them. The ability to automati-
cally select from among the available connections is called automatic migration.
There are three possible settings for automatic migration:
• visible: auto-migrates (displays on screen notices when it does so)
• on: auto-migrates (without any on screen notices)
• off: no auto-migration (forced/manual migration only; see below)
Download from Www.Somanuals.com. All Manuals Search And Download.
If you choose to turn off automatic migration in this section of the operate menu,
you will have to cycle among multiple inputs manually by pressing the front
panel input button repeatedly.
As shipped from the factory, the AVP2 automatically tries to give you your “pre-
ferred” audio connection, whenever it is available. Thus if for laserdisc you have a
Dolby Digital RF connection as your “first choice,” followed by a normal digital
connection, followed by the analog connection (all specified in your set source
button screen), the system will automatically “migrate” down to the digital when
the RF signal is not available, and migrate back “up” to the RF output when it be-
comes available once again. (This example assumes you have the optional RF de-
modulator, of course.)
migrating to analog If the automatic migration feature moves to an analog connection, it will stay
there until you either force a manual migration (see below) or select a different
input. This is due to the fact that the hardware that would normally be detecting
a restored digital signal is already fully occupied receiving your analog signal af-
ter it has been converted to digital. With most laserdisc players, this is not a prob-
lem; nor is it a problem with other sources, whose digital outputs are always
available. However, certain combination DVD/laserdisc players mute their digital
outputs when in pause or stop, forcing the AVP2 to “look elsewhere” for a usable
signal.
In these cases, it is generally best to set up a separate button (perhaps a more
button) dedicated to the analog connection from these combi players. Ordinarily,
you would use this connection only when playing old laserdisc that had only
analog soundtracks.
39
forced/manual migration Additionally, even when auto migration is set to either on or visible, you can al-
ways temporarily engage manual migration simply by pushing the same input
button repeatedly (which cycles through the connections associated with that
button). As soon as you select any other input button, automatic migration will
reengage.
Important Note:
Even with automatic migration on and/or visible, once you
force a “manual” migration by re-selecting the same input
button, the AVP2 has no way of knowing when you would like
to return to automatic migration. Thus, it automatic migration
will remain off until you change inputs, when it reverts to the
preference you established in the Operate Menu.
simulcast A “simulcast” is defined as simultaneously watching a picture from one source
while listening to the audio from another source.
The most common example given of why one might wish to do this is for watch-
ing a nationally-television sporting event, while listening to the local radio broad-
cast of the same event, rather than to the national sportscaster. (Presumably, your
local sportcaster will favor the local team more overtly than the national fellow,
who must maintain some impartiality.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Another example might be creating “video wallpaper” during a party, wherein
you display a slide show or movie in the background, accompanied by music of
your choice.
If the ability to create such simulcasts whenever you might want them appeals to
you, change the simulcast setting of this menu to on. You may then select the
simulcast you want by choosing the picture, followed by the sound that you
would like.
By default, whenever a video source is selected, the audio that normally would
accompany that source is automatically selected with it. Your second selection
overrides this default. Both indicator LEDs will illuminate to indicate your selec-
tion.
If you find the possibility of having more than a single source selected at once
somewhat confusing, simply change the simulcast setting back to off.
setup: locked/unlocked Once the AVP2 is completely setup, calibrated and ready to go, you may want to
change this setting from setup: unlocked to setup: locked to make it more diffi-
cult to accidently disturb the carefully calibrated settings in the Setup and Custom
Menus. Toggle the lock on and off by moving the “select-it” cursor to this item,
changing to the “change-it” cursor by pressing enter, and pressing either volume
+ or volume – (with only two settings, either plus or minus will work). Then save
your change by pressing enter.
40
display preferences Pressing enter while the cursor is at this line will take you to a submenu that
provides several controls that affect the behavior of the on screen display of the
AVP2. The items on this submenu are detailed below.
DISPLAY PREFERENCES
DISPLAY POSITION
ON SCREEN STATUS: YES
STATUS PREFERENCES
TIMEOUT: 3 SECONDS
CHARACTERS: NORMAL
BACKGROUND COLOR: BLUE
display position The displayed position of the on screen messages for volume changes, surround
mode changes, etc., can be moved up or down to suit the needs of your system.
This flexibility allows you to place your AVP’s on screen information where it
won’t conflict with other on screen information. As an example, you may want to
place the on screen display near the middle of the screen so that changing aspect
ratios on a digital television doesn’t place information off the edge of the view-
able area..
on screen status Normally, the AVP2 will display on screen messages to keep you informed as to
the current status of the system. These include on screen displays of things such
as changes in volume, input, and surround mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you find these on screen messages distracting or intrusive, you may turn them
off simply by moving to the on screen status line of the display preferences
→
menu, pressing enter to toggle to the “change it” cursor ( ), and turning it off.
You may, of course, turn it back on at any time by repeating the process.
status preferences The AVP2 can display a wealth of information about the source and nature of the
signal being listened to, any signal processing going on, and other details about
the operation of the system. (See Using the Special Menu for more details.) How-
ever, if you find that this display is more than you need or want, you can turn off
individual lines of the display in this submenu.
The information that can be displayed includes:
• source info
• signal info
• mode info
• rate info
the source(s) providing the sound and picture
the nature of the incoming signal
the surround processing mode being used
the bit rate of the incoming audio signal, or
the output sampling rate of the AVP2’s DACs
whether one or more subwoofers is active
the current volume setting
STATUS PREFERENCES
SOURCE INFO: ON
SIGNAL INFO: ON
MODE INFO: ON
RATE INFO: ON
SUB INFO: ON
• sub info
• volume info
• migration info
• record info
whether automatic or manual migration is active
the source selected on the record path
VOLUME INFO: ON
↓ MIGRATION INFO: ON
Simply move the cursor to the status preferences line and press enter. Then
move the cursor to whichever item you prefer to leave off, press enter, and turn it
on or off with the volume ± buttons; then press enter again to save your change.
You may, of course, change anything again at a later time by repeating the pro-
cess.
RECORD INFO: ON
41
Note that a downward-pointing arrow at the bottom line shown on the screen
indicates that there is more to the menu below the bottom of what can be dis-
played on your screen. You can scroll down to this part of the menu simply by
moving the cursor past the last item shown on the list. Once this is done, there
will be an upward-pointing arrow to indicate that the first line has now moved
off the top of the screen.
display timeout This setting controls the duration of these on screen messages generated by the
AVP2 when you change something. (Remember that you can disable the on
screen display entirely by turning off the on screen status item on the menu.) You
can set it for 2, 3, 4, or 5 seconds, according to your preference.
display of text On screen messages are normally displayed with a black fringe around their
white letters when superimposed on live video signals. This display method is
easy on the eyes and almost always easily read. However, you can opt to have the
on screen messages displayed within a black box to ensure legibility even against
extremely bright backgrounds, when white letters might otherwise be difficult to
read.
display background color The default background color for the screen when lacking a live video signal, or
when in the menu system, is blue. This blue screen serves as a reminder that
your television is on when in fact you may prefer to turn it off.
Download from Www.Somanuals.com. All Manuals Search And Download.
Some people may prefer a green screen to differentiate the screen generated by
the AVP2 from other components in their system. Still others may prefer to leave
their projection televisions on in order to keep them warmed up and ready to
use, in which case a dark grey screen might be more desirable. (A dark grey
screen would facilitate listening to music in a darkened room, for example, and
saves unnecessary wear on the phosphors within the projector while keeping it
warmed up and ready to go.)
This menu item allows you to choose the best mode for your system, blue, green
or dark grey.
VOLUME PREFERENCES
→ DISPLAY: ABSOLUTE
SPEED: FAST
MUTE LEVEL: -20.0
MAX VOLUME: 91.0
LATE NIGHT: HIGH
- REFERENCE LEVEL 70.0 -
volume preferences The second item on the main operate menu is volume preferences. This
submenu contains several items pertaining to how volume is controlled within
the system, which are detailed below.
volume display You have the option of displaying your volume settings either of two ways:
42
• absolute—on a scale of 0.0 (no sound) to 91.0 (extremely loud); or
• relative—on a scale which is measured “plus or minus,” relative to
the calibrated reference volume (established during calibration).
As an example, if your calibrated reference level is 70, the display would read 0 in
the relative mode when it would read 70 in the absolute mode. Most people find
absolute more intuitive, while some people find relative more informative. (For
example, those who have made many recordings, and are accustomed to VU
meters that read ± relative to a calibrated zero point, may prefer the relative set-
ting.)
When the cursor is on the volume display line, an extra line will appear at the
bottom of the menu to show you how the calibrated, reference volume would be
displayed for the current setting of either absolute or relative. This serves as a
reminder, should you forget which is which. It also disappears when you move
the cursor on to another line, so as to avoid confusion.
volume speed You may select either slow or fast response for the rate at which the volume
change accelerates when pressing and holding the volume ± keys. In all cases,
single taps of the volume keys result in single incremental steps in volume. The
volume speed chosen affects the amount of time it takes to reach maximum
speed while holding a volume ± button down.
volume mute level The magnitude of volume reduction introduced by pressing the mute key is user-
definable in increments of 0.5 dB, from -0.5 to -60.0 decibels. The factory preset is
for -20.0 (-20 dB).
Download from Www.Somanuals.com. All Manuals Search And Download.
maximum volume You may set a maximum volume allowed for your system to minimize the oppor-
tunity for damage, either to your system or to better relations with your neigh-
bors. Simply choose the maximum volume setting you would like to be able to
use and save the change (by pressing enter, as always). If you decide to change it
again, simply revisit this menu item and reset it.
late night Modern movie soundtracks, especially those of action movies, often have enor-
mous dynamic range. There are times when this extraordinary dynamic range is
a problem rather than a benefit—for example, when listening late at night while
others in the home are sleeping, or in an apartment building when neighbors are
at home and prefer not to be disturbed.
Simply turning the volume down may not be an adequate solution in these cases,
as it may make dialog so quiet as to be unintelligible, and obscure important but
subtle cues in the soundtrack. The solution to this problem makes use of some
specific information provided by Dolby Digital (AC-3) soundtracks to provide ap-
propriate compression to reduce the dynamic range to something better suited to
the environment. Since this feature depends on information only available within
AC-3 soundtracks, it is only available when the AVP2 is decoding AC-3.
The late night feature may be toggled on and off on by using the special button
on the remote control (see Using the Special Menu); this item on the volume
preference menus determines how much compression is used. Your choices are
either low or high levels of compression, which may be selected according to
what works best in your particular situation.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
SET DIRECT BUTTONS
DEFINE BUTTON VCR2/DISC2
SET DIRECT BUTTONS
SET MORE BUTTONS
SET SPEAKERS
VCR 1
DISC 1
VCR 2/DISC 2
TV/AUX
SATELLITE
CD
↓ TAPE
NAME: LD
TYPE: A/V
VCR2/DISC2 AUDIO CONNECTORS
VIDEO: COMPOSITE 4
AUDIO DELAY: 0 MS
2-CH: PRO LOGIC II + THX
MULTI-CH THX: FORCE ON
↓RECORD DEVICE: NO
AUDIO CONNECTORS: 3
1: DIGITAL 3 RF
2: DIGITAL 2
SURROUND DEFAULTS
3: ANALOG 2
AUX
TUNER
AUDIO CONNECTORS
DEFINE BUTTON CD
CD AUDIO CONNECTORS
AUDIO CONNECTORS: 1
1: DIGITAL 1
NAME:
TYPE: AUDIO
CD
AUDIO DELAY: O MS
2-CH: 2-CH/SURROUND OFF
MULTI-CH THX: FORCE OFF
RECORD DEVICE: NO
AUDIO CONNECTORS
SET MORE BUTTONS
DEFINE BUTTON MORE 1
MORE-1 AUDIO CONNECTORS
MORE 1
MORE 2
MORE 3
MORE 4
MORE 5
MORE 6
↓ MORE 7
NAME: 8-TRACK
TYPE: AUDIO
AUDIO CONNECTORS: 1
1: ANALOG 8
AUDIO DELAY: 0 MS
2-CH: STEREO SURROUND
MULTI-CH THX: NOT USED
RECORD DEVICE: NO
AUDIO CONNECTORS
MORE 8
SET SPEAKERS
SET CONFIGURATION
SET CONFIGURATION
SET DISTANCE
SET LEVELS
FRONT L&R: 70Hz HPF
CENTER: 80Hz HPF
REAR L&R: 80Hz HPF
SUBS: LOW PASS
BASS LEVEL MANAGER
AUX1: RIGHT BACK
AUX2: LEFT BACK
RESET CONFIG FOR THX
SET DISTANCE
SURROUND MODE DEFAULTS
SET LEVELS
LEFT: 10.0 ft
CENTER: 10.0 ft
RIGHT: 10.0 ft
RIGHT BACK: 10.0 ft
R SURROUND: 10.0 ft
L SURROUND: 10.0 ft
LEFT BACK: 10.0 ft
DEFAULTS: ENABLED
DOLBY DIGITAL
DTS
LEFT: 0.0 dB
CENTER: 0.0 dB
RIGHT: 0.0 dB
RIGHT BACK: 0.0 dB
R SURROUND: 0.0 dB
L SURROUND: 0.0 dB
LEFT BACK: 0.0 dB
SUB: 0.0 dB
MPEG
44
2-CH/SURROUND OFF
DOLBY PRO LOGIC
↓ PRO LOGIC + THX
SUBWOOFER: 10.0 ft
UNITS: ENGLISH
PRO LOGIC II MOVIE
PRO LOGIC II + THX
PRO LOGIC II MUSIC
STEREO SURROUND
MONO SURROUND
MONO CENTER ONLY
MONO FRONTS
BASS LEVEL MANAGER
TEST SIGNAL: OFF
TEST/NEW LEVEL: 35.0
DOLBY DIGITAL
SAVED LEVEL: 65.0
CENTER:
SURROUNDS:
BACKS:
0.0
0.0
0.0
0.0
SUB:
SUB MODE: FORCE ON
THX: ON
The Setup Menu
As you might surmise from the menu system shown above, the setup menu is
where you define what associated equipment you are using with your AVP2, and
how you want the system to work for you.
Download from Www.Somanuals.com. All Manuals Search And Download.
To take a common but surprisingly complex example, imagine:
• that you have a laserdisc player that has an RF Dolby Digital
(AC-3) output, a digital output, and analog outputs;
• that you usually listen to it in THX cinema mode, whether using
discrete digital soundtracks or Dolby Pro Logic soundtracks;
• and that you prefer to use a subwoofer for movies for the extra
impact, but prefer not to use it when listening to music.
The setup menu is where you “explain” all this to the AVP2, so that all you have
to do when you want to watch a laserdisc is press a single button. The system
can easily do everything else for you. It even figures out which of the three con-
nections (AC-3, normal digital, and analog) it needs to use without you having to
read the fine print on the back of the laserdisc jacket.
We’ll take each of the submenus in turn.
define source buttons Each of the buttons on the on the top row of the front of the AVP2 may be asso-
ciated with any of the audio and video connectors on the rear of the AVP2. In
fact, each button can be associated with a maximum of three audio connections
(the AC-3 RF input if you have the RF demodulator, plus a digital input, plus a set
of analog inputs on the AVP2), and one video connection.
The reason for this extraordinary flexibility is that we want you to be able to use
the button that makes sense for each component, regardless of the type of con-
nector it may require. By manually associating whatever connector you need to
use with the button you want to use, you can make the system work the way
you want it to work.
45
Moreover, we feel the system should handle the day-to-day details of sorting out
RF AC-3, digital and analog soundtracks for you, rather than you having to read
the fine print on each disc you own. By assigning more than one connector to a
given button (as needed), the system can search for a usable signal rather than
making you do it, according to the list you give it during setup.
Thus, we give you a scrolling list of all ten input buttons, and give you the op-
portunity to tell the AVP2 which connectors you would like it to use when you
press that button. Your first connector is also your “first choice,” the priority con-
nection; second choice is second priority; and third connector selection is the
“last resort.” (That is, when there is nothing to listen to on the first and second
choices.)
example: setting up A couple examples will help. With a simple CD transport, you might set up your
a cd transport default selections as follows:
Download from Www.Somanuals.com. All Manuals Search And Download.
SET DIRECT BUTTONS
DEFINE BUTTON CD
CD AUDIO CONNECTORS
VCR 1
DISC 1
NAME:
TYPE: AUDIO
CD
AUDIO CONNECTORS: 1
1: DIGITAL 1
VCR 2/DISC 2
TV/AUX
SATELLITE
CD
AUDIO DELAY: O MS
2-CH: 2-CH/SURROUND OFF
MULTI-CH THX: FORCE OFF
RECORD DEVICE: NO
AUDIO CONNECTORS
↓ TAPE
AUX
TUNER
renaming source buttons Your first decision: would you like the on screen display to identify your CD
transport with something more specific than a generic cd name? If so, enter the
characters one at a time, up to a maximum length of seven.
1
MOVE THE SELECT-IT CURSOR BESIDE “NAME:” AND PRESS ENTER TO
ALLOW FOR CHANGES TO BE MADE.
A blinking box indicates the first available space for your new name. If you
need to move it, press any AVP2 button on the remote other than the usual
four you use for navigating menus. The audio button will do nicely, and is
conveniently nearby on the remote control.
2
USE THE VOLUME ± BUTTONS TO SCROLL THROUGH THE LIST OF
AVAILABLE CHARACTERS UNTIL YOU SEE THE ONE YOU NEED
This system works similarly to the titling feature on many camcorders. Avail-
able characters include the alphabet, all numbers, and various punctuation
marks, including blank spaces for separating words.
46
3
4
MOVE ON TO THE NEXT CHARACTER BY PRESSING ANY AVP2 BUTTON
ON THE REMOTE OTHER THAN THE FOUR YOU USE FOR NAVIGATING
MENUS.
As before, the audio button will do nicely, and is conveniently nearby.
REPEAT UNTIL YOU HAVE THE ON SCREEN NAME YOU WANT THE SYSTEM
TO USE; WHEN DONE, PRESS ENTER TO SAVE THE NAME
As always, enter saves a change. If you get part way through the process of
changing the name (or any other adjustment in the menu system) and
change your mind, you can cancel your changes by pressing menu. This
will leave the name unchanged from what it had been before you started.
defining the input type In the case of setting up your CD transport, defining an input type is pretty
simple: it can be either an audio input, or unused. (You should choose the latter
for any input buttons that are, in fact, unused in your system. Doing so will re-
mind the casual user of the system of this fact when they press the wrong button
by accident, by displaying a message on screen: input not used. The main display
on the AVP2 will also display not used. The AVP2 will also remove unused inputs
from the list when scrolling through availabe inputs using the next or previous
input buttons on the remote control.)
Download from Www.Somanuals.com. All Manuals Search And Download.
1
MOVE TO THE “TYPE:” ITEM IN THE MENU, PRESS THE ENTER BUTTON,
AND USE THE VOLUME ± BUTTONS TO CHOOSE “AUDIO”; PRESS ENTER
AGAIN TO SAVE THE CHANGE
In reality, this is how the unit is shipped from the factory anyway, but while
you are here you may as well see what your options are by using the
volume ± buttons to cycle through the choices. Choose audio before you
finish up, or press menu to cancel without making any changes.
setting audio delay The AVP2 allows you to introduce an overall audio delay from 0-99 milliseconds
(ms), in 1 ms increments. This is normally used for A/V sources, especially when
external video processing may delay the video signal. Rather than having poor
“lip sync” between the auio and the video, you can delay the audio to once again
match up with the video. (This can also be done in an ad hoc way, using the de-
lay button on the front panel.)
For audio-only sources like CD, you will probably leave this set to 0 ms (no de-
lay).
choosing a 2-channel mode The AVP2 also lets you choose a default surround processing mode that will au-
tomatically be applied when a plain “stereo” signal is received from this source.
For example, if you find yourself using the stereo surround mode for most of
your music listening, you can have this mode selected automatically when chang-
ing to your CD input.
Note:
These “surround modes” refer to what the system does when
given a generic, two-channel input signal, whether analog or
digital.
47
Dolby Surround encoded signals are an example of such a
two-channel signal as they enter the Audio Video
Preamplifier, one that has been encoded to provide multiple
channels when properly decoded.
Discrete multichannel signals (such as those provided by
Dolby Digital, DTS, or MPEG) will override these surround
preferences and use processing applicable to the signal
type.
If you already know what your preference is, you might as well program it in
now. If you aren’t sure, we suggest leaving the default surround mode for your CD
transport as stereo surround for now. You can always change it later.
1
MOVE TO THE “2-CH:” ITEM IN THE MENU, PRESS THE ENTER BUTTON,
AND USE THE VOLUME ± BUTTONS TO REVIEW YOUR AVAILABLE
SURROUND MODES; CHOOSE THE ONE YOU WANT AUTOMATICALLY
ENGAGED; PRESS ENTER AGAIN TO SAVE THE CHANGE
Of course, during day to day operation, you can easily override this default
selection by simply pressing the mode button on the remote control (or the
surround mode button on the front panel) at any time. Doing so will cycle
you through the available surround modes.
Download from Www.Somanuals.com. All Manuals Search And Download.
multichannel THX The AVP2 also allows you to specify, on a source-by-source basis, whether you
would like to apply THX Ultra II post processing to any multichannels signals
(like Dolby Digital or DTS) that are received from this source component. You
can always toggle THX on and off using the special button on the remote (see
The Special Menu for more details)—this setting merely determines the default
settings you would like to use most of the time.
Since the only multichannel signal likely to be received from a CD player is a
DTS music recording, you would probably want to force off THX when using
your CD player. Other options include force on and use default, the latter indicat-
ing that the AVP2 should continue doing whatever it would have been doing
prior to receiving the multichannel signal.
is it a recording device? If this component were capable of recording (a CD-R, tape deck, VCR, etc.), and
assuming you wanted to make recordings through the system, you would need to
make another connection to provide for making those recordings. Specifically, you
would need to use the record output on the AVP2 to feed the recording device a
signal to be recorded.
Moreover, the system needs to know which sources are hooked up in this way to
ensure that you do not accidently send a source back to itself to be recorded—a
situation that can produce unpleasant and even speaker-threatening feedback
loops. For these reasons, we need to let the system know which of our sources
are connected to a record output.
48
1
MOVE TO THE “REC OUT:” ITEM IN THE MENU, PRESS THE ENTER BUTTON,
AND USE THE VOLUME ± BUTTONS TO INFORM THE SYSTEM WHETHER A
RECORD OUTPUT IS BEING USED WITH THIS SOURCE COMPONENT;
PRESS ENTER AGAIN TO SAVE THE CHANGE
Your choices are no, warn, and prohibit. For a CD transport, you’ll probably
leave it at no. If you were setting up a cassette deck, you should choose
prohibit, which would ensure that you do not accidently send a source
back to itself to be recorded.
The warn option is for sophisticated users who understand the potential
dangers of feedback loops and how to avoid them, but wish to have the
ability to set up such a potential situation for a specific reason. In this case,
the AVP2 will put up an on screen warning about the record loop, but al-
low it to be selected nonetheless.
Note:
We do not recommend the use of the “warn” feature for most
users or situations, but provide it to solve specific problems
sometimes encountered with outboard equalizers, etc.
how many input connectors? How many physical connections does this component require? (A stereo pair of
analog signals is considered “one connection” for the purposes of this discus-
sion.) In the case of a CD transport, the answer is easy. All you have is a digital
output to accommodate, so the answer is one. A laserdisc player is the most com-
plicated, since it might have three sets of signals: RF Dolby Digital (AC-3), normal
Download from Www.Somanuals.com. All Manuals Search And Download.
(S/PDIF) digital, and a pair of analog outputs for the occasional old disc that has
only analog soundtracks. (This would be a pretty old disc, but they do exist.…) In
this extreme case, you would need three sets of connections. We’ll come back to
laserdisc later—for now, let’s stick with your CD transport, with its single connec-
tion.
1
MOVE TO THE “AUDIO CONNECTORS:” ITEM IN THE MENU, PRESS THE
ENTER BUTTON, AND USE THE VOLUME ± BUTTONS TO INFORM THE
SYSTEM HOW MANY CONNECTIONS ARE NEEDED; PRESS ENTER AGAIN
TO SAVE THE CHANGE
As you work with the menu system a bit, the habit of pressing enter to
work with an item and then pressing it again to save your work becomes
second nature.
defining input connectors Once the AVP2 knows how many connections you need for this particular com-
ponent, it updates its menu to provide for defining those connections. With only
a single digital connection (for your CD transport), this is pretty simple. Just tell
the system which digital input connector you used when you hooked up the CD
transport.
1
MOVE TO THE “1:” ITEM IN THE MENU, PRESS THE ENTER BUTTON
Since there are actually two things the system needs to know, and they
would not have fit on a single line without confusion, you will be taken to
the next-lower screen, which shows two items: audio and conn (short for
“connector”).
49
CD-AUDIO INPUT 1
2
PRESS ENTER AGAIN TO WORK WITH “AUDIO:” AND CYCLE THROUGH
YOUR OPTIONS WITH THE VOLUME BUTTONS; CHOOSE DIGITAL AND
PRESS ENTER TO SAVE
AUDIO: DIGITAL
CONN: DIGITAL 1
Once again, this is the factory default setting. Were you setting up a CD
player that had only analog outputs, though, you would want to change this
to analog and use a set of analog connectors on the AVP2 instead.
3
MOVE TO “CONN:” WITH THE VOLUME BUTTONS, PRESS ENTER TO WORK
WITH IT, AND CYCLE THROUGH THE LIST OF CONNECTORS UNTIL YOU
SEE THE ONE YOU USED; PRESS ENTER TO SAVE THIS SETTING, AND
MENU TO RETURN TO THE PREVIOUS/HIGHER MENU
As mentioned during the Quick Start for CD, you can connect any source
component to any appropriate connector, and then simply tell the system
what you have done. It is helpful to have written down what components
are connected where during initial hookup, so you don’t have to try to peer
around the back of the system with a flashlight later. A form for this pur-
pose is included at the back of this manual. (Use a pencil, in case some-
thing changes in the future.)
example: setting up As mentioned earlier, a laserdisc player has several more connections that must
a laserdisc player be accommodated than does a simple CD transport. We will run through these
additional settings next, without repeating the sections that remain the same.
Download from Www.Somanuals.com. All Manuals Search And Download.
SET DIRECT BUTTONS
DEFINE BUTTON VCR2/DISC2
VCR2/DISC2 AUDIO CONNECTORS
VCR 1
DISC 1
VCR 2/DISC 2
TV/AUX
SATELLITE
CD
↓ TAPE
NAME: LD
TYPE: A/V
AUDIO CONNECTORS: 3
1: DIGITAL 3 RF
2: DIGITAL 2
VIDEO: COMPOSITE 4
AUDIO DELAY: 0 MS
2-CH: PRO LOGIC II + THX
MULTI-CH THX: FORCE ON
↓RECORD DEVICE: NO
3: ANALOG 2
AUX
AUDIO CONNECTORS
TUNER
(As a reminder, the path to the define button vcr 2/disc 2 menu shown above is
main menu/setup/set source buttons/vcr 2/disc 2—but you can get there faster
by pressing and holding the vcr 2/disc 2 button for several seconds.)
defining the video connection The appropriate type: from the define button vcr 2/disc 2 menu this time is a/v.
After having changed type: to a/v and saved the change, you will see an addi-
tional item immediately below type. The video: item establishes which video
connector you wish to associate with a particular button.
1
2
MOVE TO THE “VIDEO:” ITEM IN THE MENU, PRESS THE ENTER BUTTON
→
The arrow cursor will change to the “change-it” cursor ( ).
CYCLE THROUGH THE AVAILABLE INPUTS UNTIL YOU SEE THE ONE YOU
USED WHEN HOOKING UP YOUR LASERDISC PLAYER
The AVP2 will cycle through the entire list of available video inputs.
50
Note:
In this and other menus, connectors that are already
associated with another, different button are displayed in
yellow letters instead of white. This is done to keep you
informed as to what inputs might be available.
Now the system knows which video connector to look at when you want to
watch a laserdisc. Next, let’s move to the audio connectors. (You can change the
surround mode default along the way if you like… but you already know how to
do that.)
defining multiple The laserdisc has the greatest potential for confusion, having as it does three pos-
audio connections sible connections that may be needed. In addition, multiple versions of the
soundtrack are often present on a single laserdisc requiring some sort of decision
as to which should be used.
Ideally, the system would be able to automatically select the best available
soundtrack and give it to you without your having to become involved personally
in reading the fine print on the laserdisc jacket (and then pushing additional but-
tons) every time you watch a movie.
Download from Www.Somanuals.com. All Manuals Search And Download.
The AVP2 can provide this automatic searching for and selection of the best avail-
able soundtrack for you, according to priorities you establish during setup. In es-
sence, you are about to describe the order in which you want the AVP2 to look
for signals, establishing your first, second and third choice. Typically, this will be
RF (AC-3, Dolby Digital), normal digital (which might be a digital version of
Dolby Pro Logic, DTS discrete digital, MPEG/Musicam, or ordinary two-channel
digital stereo), and finally analog (if there is no digital signal available).
Let’s get started.
1
2
3
MOVE TO THE “AUDIO CONNECTORS:” ITEM IN THE MENU, PRESS THE
ENTER BUTTON, AND USE THE VOLUME ± BUTTONS TO INFORM THE
SYSTEM HOW MANY CONNECTIONS ARE NEEDED; PRESS ENTER AGAIN
TO SAVE THE CHANGE
Choose 3 audio connectors if you have an AC-3 RF output on your
laserdisc player, 2 audio connectors if you have only analog and digital out-
puts. Once the AVP2 knows how many connections you need for this par-
ticular component, it updates its menu to provide for defining those con-
nections.
DEFINE CONNECTOR “1:” AS YOU DID FOR THE CD TRANSPORT, USING
YOUR FIRST CHOICE CONNECTION PREFERENCES FOR LASERDISC;
SAVE YOUR CHOICES BY PRESSING ENTER
If you have an RF (AC-3)-equipped laserdisc player and the Audio Video
Preamplifier’s optional internal RF demodulator installed, this choice should
be digital (vs. analog) and dig 3 RF. Otherwise, you probably have only two
connections that need to be made, digital and analog; in this case, you’ll
want to choose digital and whatever input you used during hookup for
your laserdisc player’s digital output.
51
REPEAT THIS PROCESS FOR YOUR SECOND CHOICE (2:) AND THIRD
CHOICE (3:) CONNECTIONS AS NEEDED
With three connections, your second choice will be digital, with the third
choice being analog. If you chose to set up two connections (lacking an RF
output), then your second connection will be your analog hookup. Choose
audio: analog in the submenu, and then choose the analog input where
you hooked up the analog connections from your laserdisc player). Save
your choices by pressing enter.
setting & saving input levels The AVP2 includes a high quality analog to digital converter (ADC). Since all pro-
cessing in the AVP2 is handled in the digital domain, analog signals that are to be
changed in any way (other than volume) must first be converted to digital form.
It is extremely important to avoid overloading or “clipping” the ADC, since doing
so results in a nasty burst of distortion that sounds similar to a power amplifier
clipping. Unlike power amplifiers, this sort of clipping can occur at any volume
level, since the ADC is being clipped well before the volume control in the signal
path.
Fortunately, the AVP2 can detect when its ADC is being clipped, and posts a no-
tice to that effect in its front panel display and on the on screen display. If over-
load should occur, the AVP2 will indicate it by displaying ADC CLIPPING on the
screen (and “Clip!” in the main display). If you see such a message, you should
turn down the input level on the AVP2 (which turns down the volume of the sig-
Download from Www.Somanuals.com. All Manuals Search And Download.
nal going into the ADC). You should also probably save this new setting as the
default setting for that input, which will save you from running into this problem
again—unless you later play something that is even louder. (In which case, you
simply repeat the process outlined below.)
1
TURN THE MASTER VOLUME CONTROL ON THE AVP2 DOWN
When the analog to digital converter clips, it distorts the waveform much as
a power amplifier does when it clips. This is both unpleasant to hear and
potentially dangerous to speakers at high volumes. Turn the volume down
to a quiet, but still audible level just to be on the safe side, but so you can
still hear what you are doing.
2
3
PLAY THE LOUDEST SELECTION YOU CAN FIND ON THE ANALOG
SOURCE IN QUESTION
Mind you, you are not playing this “loud section” loudly: keep it quiet, but
play the biggest musical crescendo or movie explosion available on the
source at hand.
PRESS INPUT LEVEL ON THE FRONT PANEL OF THE AVP2 AND RAISE/
LOWER THE INPUT LEVEL WITH THE VOLUME KNOB UNTIL THE DISPLAY
JUST READS “ADC CLIPPING”; THEN LOWER THE INPUT LEVEL BY1-2 DB.
The goal here is to give yourself just a little “headroom” in case the next
recording you play is a bit louder than the one you are using for this ad-
justment. Note that some source components may have lower-than-normal
output voltages, in which case you will end up “turning up” the input level
setting to compensate.
52
4
CONTINUE TO MONITOR THE RECORDING THROUGH ONE OR TWO
MORE LOUD PASSAGES TO ENSURE THAT THE ADC DOES NOT CLIP;
SAVE THE NEW DEFAULT VALUE BY PRESSING AND HOLDING THE INPUT
LEVEL BUTTON
When you press and hold the input level button on the AVP2, the current
value for the input level adjustment is automatically entered as the default
input level setting for the currently selected analog source. (You can check
this for yourself by going into the define button menu for that input, and
checking the analog connection.) Whenever you select this input in the fu-
ture, this setting will be loaded for you to protect against harsh-sounding
ADC overload.
set more buttons When you are all done defining how you want to us the nine input buttons on
the AVP2, you may discover that you have some input connectors on the rear that
are as yet unused. Since different people require different complements of con-
nectors; we provide some redundant ones to ensure that everyone was likely to
have what they needed. As a result, the AVP2 has nine input buttons, but fifteen
audio inputs (eight analog pairs plus seven digital inputs of various types).
If you have additional sources beyond the nine most commonly used ones that
you would also like to have as part of your AVP2-based system, you can access
“virtual input buttons” via the more button (and by cycling through the defined
inputs on the remote control).
Download from Www.Somanuals.com. All Manuals Search And Download.
The process of defining a more “virtual” button is the same as that for a normal
button, with two exceptions:
• since it is only a virtual button, you cannot access the define button
menu by the press-and-hold shortcut;
• similarly, since there is no simple way to force migration between
multiple audio connections, more buttons can accept only a single
audio connection.
To define a more button, navigate through the menu system as you normally do,
down the hierarchy along the path main menu/setup/set more buttons. Then
pick a button (more 1, more 2, etc.) and define it as you would any other.
Once you have saved your “virtual button” definition, you may access it by press-
ing the more button on the front panel, or by cycling through the appropriate in-
puts from the remote (either video or audio). If you set up more than one virtual
button, pressing the more button repeatedly will cycle among them.
set speakers Having set up all of your sources, the next step is to tell the AVP2 more about
the speakers in the system. This allows the AVP2 to tailor its performance to the
needs and capabilities of your loudspeakers. Adjustments include (see next
page):
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SET CONFIGURATION
SET SPEAKERS
FRONT L&R: 70Hz HPF
CENTER: 80Hz HPF
REAR L&R: 80Hz HPF
SUBS: LOW PASS
SET CONFIGURATION
SET DISTANCE
SET LEVELS
BASS LEVEL MANAGER
AUX1: RIGHT BACK
AUX2: LEFT BACK
RESET CONFIG FOR THX
SET DISTANCE
LEFT: 10.0 ft
CENTER: 10.0 ft
RIGHT: 10.0 ft
RIGHT BACK: 10.0 ft
R SURROUND: 10.0 ft
L SURROUND: 10.0 ft
LEFT BACK: 10.0 ft
SUBWOOFER: 10.0 ft
UNITS: ENGLISH
SET LEVELS
LEFT: 0.0 dB
CENTER: 0.0 dB
RIGHT: 0.0 dB
RIGHT BACK: 0.0 dB
R SURROUND: 0.0 dB
L SURROUND: 0.0 dB
LEFT BACK: 0.0 dB
SUB: 0.0 dB
BASS LEVEL MANAGER
54
TEST SIGNAL: OFF
TEST/NEW LEVEL: 35.0
SAVED LEVEL: 65.0
• set configuration: informs the system about important characteris-
tics of the speakers being used
• set distance: to time-align the different speakers, correcting for
their various distances from the listening position (so sounds that
are supposed to reach the listener at the same time actually do)
• set levels: to adjust the loudness of the speakers relative to each
other to correct for differences in sensitivity, placement, etc.
• bass level manager: provides a convenient way to limit the
amount of deep bass that might otherwise be sent to your
subwoofer at high volumes (discrete digital soundtracks can some-
times be quite extreme in their deep bass requirements)
Each of these areas will be addressed in more detail, in turn.
Download from Www.Somanuals.com. All Manuals Search And Download.
set configuration This is where you tell the system about the bass capabilities of your speakers, as
well as how many you are using in the system.
The main speakers may be defined as full range, meaning that they can repro-
SET CONFIGURATION
duce any deep bass that might be sent to them to your satisfaction. Alternatively,
you can select a frequency from 30 to 100 Hz (in 10 Hz increments). In this case,
the front speakers will receive only information from that frequency and higher;
the lower frequencies will be re-routed to the subwoofer and/or to any full range
speakers in the system.
FRONT L&R: 70Hz HPF
CENTER: 80Hz HPF
REAR L&R: 80Hz HPF
SUBS: LOW PASS
AUX1: RIGHT BACK
AUX2: LEFT BACK
RESET CONFIG FOR THX
In the case of the center, surround and subwoofer channels, there is an additional
option: none (meaning there is no such speaker is connected to the system). Any
information designed to be reproduced by speakers you do not have will be re-
directed to available speakers so that you will hear everything you should.
(Though, of course, having more speakers is better than “faking it.”)
The aux1 and aux 2 settings refers to the 7th and 8th “auxiliary channels” included
in your AVP2. These “extra” channels may be used in any of several ways:
• Dual Drive™: if you have Dual Drive surround speakers, you can
use the Aux channels to drive the rear halves of your surrounds
while the surround outputs produce the signal for the front halves.
A special infrared command may be taught to a learning remote to
toggle between bipole and dipole modes of operation,or you may
set up your preferences in the mode defaults menu.
• Left & Right Back: if you have a large room, you may find it benefi-
cial to have two pairs of surround speakers, one pair to the sides
of the listening area and the other pair behind the listening area.
This arrangement can provide a more uniform and enveloping sur-
round field. If you select to use the Aux channels for Back speak-
ers, corresponding adjustments will appear in other menus (e.g.,
the set distance and set levels menus).
55
• Center Back: the aux1 channel may also be used for a center back
channel, in support of 6.1 channel surround modes like Surround
EX and DTS ES.
• Left Stereo Sub: you may also elect to use stereo subwoofers, in
which case the regular sub output will handle the right subwoofer
and aux 1 handles the right. Specifically, any bass information in a
“left” speaker (front, side or rear) that has been set to anything
other than full range will be reproduced in the left subwoofer;
likewise for the “right” speakers and the right subwoofer. Bass from
either the low frequency effects channel (also called the “.1” chan-
nel) or from a bass-limited center speaker will be split evenly be-
tween the left and right subwoofers.
• Extra Mono Sub: alternatively, you can use aux2 for a second mono
subwoofer output. This output contains the same information
found in the regular subwoofer output, but benefits from having
independent level and distance settings. Using a second subwoofer
in this manner is often the best way to get the smoothest. most
accurate bass in many rooms.
• Not Used: if you are not using the auxiliary channels, you should
turn them off. Doing so returns the AVP2 to a more common, 5.1
channel configuration.
Download from Www.Somanuals.com. All Manuals Search And Download.
special tip:
If you have THX-certified speakers all around, a shortcut for
setting the configuration to the THX standard is provided.
Simply move your cursor to the bottom line and press enter.
This will set the menus for all the appropriate crossover
settings at one touch. You may still select your own preference
for the Auxiliary channels, however.
If you do not have THX speakers, define which (if any) of your speakers is full
range, and select an appropriate crossover frequency for the others, below which
bass is redirected to bass-capable speakers.
1
2
3
ENTER THE SET CONFIGURATION MENU AND DEFINE HOW YOU WANT
YOUR FRONT L&R SPEAKERS TREATED
Using enter and the volume ± buttons, choose either full rng or an appro-
priate crossover frequency for your front left and right speakers. Save your
selection (enter).
REPEAT THIS PROCESS FOR THE CENTER AND REAR SPEAKERS
Remember that you have an additional option with the center speaker of
none (e.g., a phantom center channel). Similarly, if you do not yet have sur-
round speakers installed, you can select none for them as well, and the in-
formation intended for them will be mixed into the front channels.
56
DEFINE YOUR SUBWOOFER APPROPRIATELY AND RETURN TO THE SET
SPEAKERS MENU
You have the choice of full range (use this only if you intend to use the
crossover in the subwoofer instead of the one in the AVP2); low pass
(which will give the subwoofer any bass the other speakers cannot handle,
plus the “.1” low frequency effects channel); or not used if you do not have
a subwoofer. Note that without a subwoofer, the “.1” low frequency effects
channel will be redirected to any speakers defined as full range.
4
CHOOSE WHAT YOU WANT TO DO WITH YOUR AUXILIARY CHANNELS, IF
ANYTHING
As notes above, your options include dual drive, stereo backs, center
back, stereo subs, extra mono sub or not used. Note that whether dual
drive or sides, using the aux channels for surround speakers will result in
them having the same crossover characteristics as those defined for the sur-
round speakers.
important note If you define all of your speakers as full range (as in the example above), the
about your subwoofer: only signal left for the subwoofer to reproduce is the low frequency effects (LFE)
or “.1” channel in discrete multichannel formats such as AC-3. Thus your
subwoofer will normally remain inactive during other surround modes such as
pro logic and stereo surround.
If you want your subwoofer to be contributing to the overall performance of your
system more consistently, you need to give it something to do—by defining at
Download from Www.Somanuals.com. All Manuals Search And Download.
least some of your speakers as something other than full range, or by using the
extra bass feature of the AVP2’s special menu. This feature places “redundant”
bass in the subwoofer, duplicating low bass information from other channels.
set distance In order to provide optimal performance, the AVP2 needs to know where your
speakers are located relative to the primary listening position. With this informa-
tion, it can adjust the timing of the delivery of the various channels of sound so
that sounds that are supposed to reach you at the same time actually do so—
even though the speakers from which those sounds emanate may be at signifi-
cantly different distances from the listening position.
By now you should be quite comfortable navigating the AVP2 menus, so we will
simplify the “how-to” explanations. If you are coming directly to this portion of
the manual without having read the previous sections, please review those sec-
tions before proceeding. They contain important information you need to know
about, in addition to detailing the menu navigation system. Try starting at Using
the Menu System.
1
ENTER THE SET DISTANCE MENU
You will see a screen which should look something like the following:
set distance menu
SET DISTANCE
LEFT: 10.0 ft
CENTER: 10.0 ft
RIGHT: 10.0 ft
RIGHT BACK: 10.0 ft
R SURROUND: 10.0 ft
L SURROUND: 10.0 ft
LEFT BACK: 10.0 ft
57
SUBWOOFER: 10.0 ft
UNITS: ENGLISH
Note that this menu updates dynamically to reflect the choices you made in
the Set Configuration menu. For example, if you are using Dual Drive sur-
rounds, you will be given a single distance for each surround speaker, rather
than separate distances for sides and back surround speakers.
(If you prefer to use the metric system, move down to units: and toggle it
from english to metric. The rest of the screen will then update to suit your
preference.)
2
3
MEASURE THE DISTANCE FROM EACH SPEAKER TO THE MAIN LISTENING
POSITION; ENTER THESE DISTANCES INTO THE TABLE DISPLAYED ON
SCREEN
Using a tape measure, measure these distances to the nearest 0.5 feet (or
0.2 meters). Use the volume ± buttons to move the values up or down as
needed; enter each as you go along.
MAKE A NOTE OF THESE SETTINGS UNDER “YOUR SYSTEM SETTINGS” IN
THE BACK OF THIS MANUAL
Having these settings handy will prove helpful should anyone ever tamper
with your careful calibrations. Of course, you should re-calibrate the system
if you move the speakers or listening position significantly.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SAVE ALL YOUR CHANGES AND RETURN TO THE SET SPEAKERS MENU
Once you have each channel adjusted properly, press menu to return to the
set speakers menu so you can continue the initial setup of your system.
set levels The AVP2 incorporates level controls for each channel. These allow you to com-
pensate for differences in amplifier and speaker sensitivities, and for placement
variations in different rooms. These adjustments are essential for reproduc-
ing proper soundstaging and image localization. Fortunately, they are nor-
mally a onetime adjustment during setup, and only need to be revisited if ampli-
fiers or speakers change.
The simplest and best way to adjust the output level controls is by using an
Sound Pressure Level (SPL) meter and the internal test tone generator. The goal is
to set the volume at the primary listening position to read 75 dB SPL (C-weight-
ing, slow response mode) from each speaker in sequence, using the individual
output level controls. An appropriate SPL meter can be purchased from Radio
Shack for about $35 U.S. (tip: buy the analog meter rather than the digital one).
You should point the meter at the ceiling in order to avoid inadvertently favoring
one speaker over another.
In the absence of an SPL meter, it is possible (though less desirable) to set the
output level controls by ear. Use the built-in pink noise generator in the AVP2 to
adjust all volumes to sound the same as they cycle around the various speakers.
(This signal uses bandwidth-limited pink noise to limit the problem of timbre shifts
between speakers influencing the setting of levels.) The system will then be rea-
sonably well balanced, although of course it is not “calibrated.” We urge you to
use an SPL meter as soon as practical.
58
1
ENTER THE SET LEVELS MENU
Select set levels in the set speakers menu and press enter. You will then
see a screen which should look something like the following:
set levels menu
SET LEVELS
LEFT: 0.0 dB
CENTER: 0.0 dB
RIGHT: 0.0 dB
RIGHT BACK: 0.0 dB
R SURROUND: 0.0 dB
L SURROUND: 0.0 dB
LEFT BACK: 0.0 dB
SUB: 0.0 dB
As with the Set Distance menu, the Set Levels menu is dynamically updated
to reflect the choices you have made in the Set Configurations menu. For
example, Dual Drive speakers are sent identical amplitude signals to both
front and rear halves during calibration, avoiding the need for separate cali-
bration.
2
RAISE OR LOWER THE LEFT FRONT SPEAKER’S VOLUME TO 75 DB SPL AS
MEASURED AT THE PRIMARY LISTENING POSITION
Select the left front speaker by moving the cursor to that line; you can then
modify the setting by pressing enter. Use volume ± to adjust the volume of
that particular channel. Remember that you should be using the “C” weight-
ing curve and the “Slow” ballistics of the SPL meter in order to get an accu-
rate reading. Save your change by pressing enter again.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
REPEAT THIS PROCESS FOR EACH SPEAKER IN TURN
Pressing volume ± will move the cursor (and the test noise) on to the next
speaker. When adjusting the subwoofer level, be sure to get up and walk all
around the listening area, watching for the magnitude of the variations in-
troduced by room modes at low frequencies. If more than 3-4 decibel
variations are seen within the listening area, consider relocating your
subwoofers for more consistent results. (See Planning Your Installation for
specific suggestions on subwoofer placement.)
4
5
MAKE A NOTE OF THESE SETTINGS UNDER “YOUR SYSTEM SETTINGS” IN
THE BACK OF THIS MANUAL
Having these settings handy will prove helpful should anyone ever tamper
with your careful calibrations. Of course, you should re-calibrate the system
whenever changing amplifiers and/or speakers, or when something has a
noticeable effect on room acoustics (such as rearranging the furnishings).
SAVE ALL YOUR CHANGES AND RETURN TO THE SETUP MENU
Once you have each channel adjusted properly, press menu to return to the
set speakers menu so you can continue the initial setup of your system.
bass level manager Some powered subwoofers have built-in protection against overload, or have am-
plifiers designed to be incapable of destroying the subwoofer driver itself. If your
system enjoys this sort of protection, leave the Audio Video Preamplifier’s bass
level manager at its maximum (and therefore effectively disabled) setting. After
all, the speaker designer knows the limitations of his/her product better than ei-
ther you or we can. It’s best to let the speaker designer decide.
59
However, many subwoofers lack any protection against being overdriven other
than your own discretion in using the volume control. While this discretion is al-
ways a good thing — if your system starts to sound distorted, “fuzzy” or garbled
at high volumes, turn it down! — some people might prefer to have the system
itself provide a measure of additional protection. This task falls to the bass level
manager.
With the advent of discrete multichannel digital audio, it is possible to have six
(or more) channels of information that contains deep bass frequencies. In many
cases, the only speaker in the system that can reproduce deep bass is a single
subwoofer. If one subwoofer is expected to do the work of six speakers, and the
listener-controlled volume is turned up fairly high, it is easy to imagine the
woofer being taken beyond its limits. (Incidentally, there are significant sonic ad-
vantages to having multiple subwoofers when possible, in addition to simply in-
creasing the maximum volume that can safely be enjoyed. You may want to con-
sider using two subwoofers.)
bass level manager menu
BASS LEVEL MANAGER
TEST SIGNAL: OFF
TEST/NEW LEVEL: 35.0
SAVED LEVEL: 65.0
Download from Www.Somanuals.com. All Manuals Search And Download.
With the bass level manager, you are given an opportunity to establish a maxi-
mum volume beyond which you do not want your subwoofers to go. If you are
reasonably judicious with your main volume control during listening, you do not
have to perform this adjustment at all. It is provided to give you the option of
imposing an artificially low upper limit on bass transients (explosions, etc.), with-
out affecting the perceived balance of bass at normal volumes.
1
ENTER THE BASS LEVEL MANAGER MENU AND CHOOSE
TEST SIGNAL: ON
You have the option of setting the bass level manager volume level arbi-
trarily, without the benefit of listening to a test signal; or by listening to a
low-frequency (bandwidth-limited) pink noise signal through the
subwoofer(s). After experimenting with the bass level manager, you might
want to reset it to its maximum setting (effectively disabling it). This would
be best done without having to endure an extremely loud test signal (e.g.,
test signal: off).
When you choose to use the test signal by changing test signal: from off to
on, the low frequency test signal will be sent to your subwoofer(s) at a
modest volume. Regardless of the previous setting, the initial setting of the
bass level manager when you enter its menu is a low value of 30. This is
done to avoid a sudden, potentially speaker-endangering level of the test
signal being sent to your subwoofer(s).
2
RAISE THE VOLUME OF THIS TEST SIGNAL TO THE LOUDEST LEVEL YOU
ARE LIKELY TO WANT TO HEAR FROM YOUR SUBWOOFERS, BEING
CAREFUL NOT TO OVERDRIVE THEM; SAVE THIS SETTING
60
This is a potentially tricky area, since you don’t want to limit the perfor-
mance of your subwoofers unnecessarily. At the same time, neither do you
want to overdrive them during the calibration of the system! (One way out:
have your dealer do the calibration, since he or she is more familiar with
the capabilities of the speakers you purchased.) Save the setting by pressing
enter, which also turns off the test signal and resets its next turn-on level to
30. (This last step on the AVP’s part ensures that the test signal always starts
out at a modest volume.)
surround mode defaults The AVP2 also allows you to customize its default configuration for each surround
mode. Although the most accurate reproduction will be achieved by leaving these
adjustments disabled, their inclusion does allow you the option of tailoring the
sound of various surround modes to suit your individual taste. For example, if
you find yourself turning up the rear speakers whenever you watch a movie, and
then turning them back down to their normal, calibrated setting for music, you
may want to set the defaults for Dolby Digital (e.g. AC-3) and stereo surround ac-
cordingly, to automate those changes.
before you use
surround mode defaults
We recommend living with the AVP2 and using it in its calibrated
settings for a while before changing these defaults. There is an ad-
justment period people go through when their system is upgraded,
during which it is difficult to make an accurate decision about
sound quality. The best-known example of this is when someone
first owns a high quality subwoofer: the tendency is to turn it up
too loud initially (so one can “hear it”); as time goes by, most
Download from Www.Somanuals.com. All Manuals Search And Download.
people find themselves gradually turning it down until it is ad-
justed to a more accurate level that blends appropriately with the
rest of the system. Similarly, there is a tendency to exaggerate the
bass and surround channels in surround systems before one ad-
justs to a high quality multichannel experience.
Remember that ad hoc adjustments (to compensate for a poor recording, for ex-
ample) on the system are always easy to make. Simply touch the button for the
speaker(s) you wish to adjust, and then raise or lower the volume. These offsets
from the calibrated settings remain active until you change them again, or until
you press recall to restore the AVP2 to its calibrated settings, or until the AVP2
locks onto a new signal (as when you change inputs).
The surround mode defaults simply automate the manual process. For each of
the surround modes of the AVP2, you may create default offsets for center, sur-
rounds, backs, and sub channels (as appropriate for the system configuration you
have set up). The system will simply enter these default settings for you as it
switches from one surround mode to the next. As always, you may alter these set-
tings as you see fit from the front panel or from the remote control. You may also
return to the calibrated (no offsets) setting by pressing recall.
In addition to leaving the subwoofer in its default setting (as determined by the
set speakers menu settings), you may also elect to force on or force off the
subwoofer. This effectively allows you to change the speaker configuration for
each surround mode, at least as far as bass management is concerned. Thus, if
you prefer to use a pair of high quality speakers full range for music, but wish to
add a subwoofer only for movies, you can have the system handle these details
for you automatically when switching among surround modes.
61
In addition, you may select to operate the AVP2 in an extra bass mode, wherein
all deep bass is sent to all speakers capable of reproducing it. This may in fact
exaggerate the deep bass somewhat, as compared to the director’s intention. But
it also solves the problem of your subwoofer having nothing to do during a
Dolby Pro Logic soundtrack, when the main speakers are all designated as full
range.
If you are using Dual Drive™ surround speakers, you may also set a default of
either bipole or dipole for each surround mode, as appropriate.
To change the default offsets for your various surround modes, you must first en-
able this special feature for all surround modes, then alter each as you like:
1
FROM THE SETUP MENU, SELECT “SURROUND DEFAULTS” AND ENABLE
THE FEATURE
After selecting surround defaults from the setup menu, you will see a
screen that looks like this:
SURROUND MODE DEFAULTS
DEFAULTS: DISABLED
Download from Www.Somanuals.com. All Manuals Search And Download.
You must first engage this feature by pressing enter, then volume ± to toggle
DISABLED to ENABLED. This enables a menu that in turn has several
submenus, examples of which are shown below:
SURROUND MODE DEFAULTS
DOLBY DIGITAL
DEFAULTS: ENABLED
DOLBY DIGITAL
DTS
CENTER:
SURROUNDS:
BACKS:
0.0
3.0
3.0
3.0
MPEG
SUB:
2-CH/SURROUND OFF
DOLBY PRO LOGIC
↓ PRO LOGIC + THX
SUB MODE: FORCE ON
THX: ON
PRO LOGIC II MOVIE
PRO LOGIC II + THX
PRO LOGIC II MUSIC
STEREO SURROUND
MONO SURROUND
STEREO SURROUND
CENTER:
SURROUNDS:
BACKS:
0.0
0.0
0.0
0.0
MONO CENTER ONLY
MONO FRONTS
SUB:
SUB MODE: FORCE ON
This extra step ensures that any automated changes of output levels are
consciously chosen and therefore less likely to cause surprises. It also allows
you to disable all the surround mode defaults in one easy step, should you
decide at some future date to return to the calibrated settings for all your
routine listening.
62
2
SELECT THE SURROUND MODE YOU WOULD LIKE TO MODIFY
For example, when you have selected the Dolby Digital mode, you might
see a screen that looks something like this:
DOLBY DIGITAL
CENTER:
SURROUNDS:
BACKS:
0.0
0.0
0.0
0.0
SUB:
SUB MODE: FORCE ON
THX: ON
Other surround modes may have fewer items, since only those adjustments
that are appropriate to a given surround mode are displayed. Thus, (for ex-
ample) center, surrounds and backs are omitted on 2-ch/surround off.
3
ADJUST THE LEVEL OF CENTER, REAR AND SUB CHANNELS RELATIVE TO
THE FRONT LEFT AND RIGHT SPEAKERS TO SUIT YOUR PREFERENCE
Using the volume ± buttons, move the cursor to the item you wish to ad-
just; press enter; then adjust the setting with the volume ± buttons. Save
each setting as you go along by pressing enter.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SELECT “NO CHANGE,”“FORCE ON,”“FORCE OFF” OR “EXTRA BASS”
AS THE SETTING FOR YOUR SUBWOOFER IN THIS SURROUND MODE
If you select no change as the sub mode for all your surround modes, the
AVP2 will leave the AVP2’s bass management settings as they had been
prior to selecting this surround mode. This no change setting is best used
on all surround modes or none; if you elect to specify force on or force off
in some modes, you should probably do so for all modes.
If (for example) you prefer to ensure that a subwoofer is included for mov-
ies and removed when listening to music, you should set speakers for a
biamplified system (with whatever crossover frequency best supports your
speakers); then set the movie-related surround modes for sub mode: force
on; and set the music-oriented surround modes to sub mode: force off.
This way, your subwoofer will automatically be engaged or disengaged as
you change between (for example) Dolby Digital and stereo surround.
The extra bass setting sends all deep bass information to both the full
range Left and Right speakers and to the subwoofer. Technically, this is “re-
dundant” bass, though in some situations it may result in smoother in-room
bass response, due to the way your speakers are interacting with the room’s
acoustics. Consult with your dealer on how best to use this feature, or
whether it even applies to your situation.
5
6
IF YOU HAVE DUAL DRIVE SURROUND SPEAKERS, SELECT EITHER
“DIPOLE” OR “BIPOLE” FOR THE DEFAULT SETTING OF YOUR SPEAKERS
FOR THIS SURROUND MODE
If you have not already selected dual drive as the way you wish to utilize
your auxiliary channels (in the set speakers menu), this option will not
even appear. This is normal, and intended to avoid misleading you, since
the setting would have no meaning without dual drive speakers.
63
PRESS “ENTER” TO SAVE YOUR CHANGES; REPEAT FOR ALL OTHER
SURROUND MODES, AS NEEDED
Note that if you change only a single surround mode, the others will re-
mains at their factory default settings of no offsets and sub mode = default.
This will cause even offsets entered at the front panel to be reset to all ze-
ros when selecting surround modes other than the one you altered. (All the
more reason to live with the system for a while before electing to customize
it in this way. You should know your preferences with a fair degree of cer-
tainty before automating them to this extent.)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAIN MENU
OPERATE
SETUP
CUSTOM
ABOUT...
CUSTOM
TEACH REMOTE
TEACH REMOTE
TRIG 1 SOURCE: STANDBY
TRIG 1 TYPE: PULSE
TRIG 2 SOURCE: STANDBY
TRIG 2 TYPE: LEVEL
REAR IR IN: REMOTE
MP-8/9 LINK: ON
PANEL BUTTONS
REMOTE ONLY
DIRECT ACCESS
SPECIAL
PANEL BUTTONS
LINK MASTER: ON
PRESS FRONT PANEL KEY
REMOTE ONLY
DIRECT ACCESS
SPECIAL
SURROUND MODES
PATH
MORE INPUTS
MISC CONTROL
NEXT VIDEO
PREV VIDEO
NEXT AUDIO
PREV AUDIO
VOLUME UP
SURROUND MODES
SURROUND OFF
DOLBY PRO LOGIC
PRO LOGIC + THX
PRO LOGIC II MOVIE
PRO LOGIC II + THX
PRO LOGIC II MUSIC
↓ STEREO SURROUND
PATH
↓ VOLUME DOWN
MAIN
REMOTE
BOTH
PRESS MUTE TO TEACH
MENU
ENTER
DISPLAY
PRESS MUTE TO TEACH
STATUS
MONO SURROUND
MONO FRONTS
MONO CENTER ONLY
LATE NIGHT
THX TOGGLE
DUAL DRIVE TOGGLE
PRESS MUTE TO TEACH
MORE INPUTS
SPECIAL
MORE 1
MORE 2
MORE 3
MORE 4
MORE 5
MORE 6
↓ MORE 7
CONTROL TRIGGER 1 ON
CONTROL TRIGGER 1 OFF
CONTROL TRIGGER 2 ON
CONTROL TRIGGER 2 OFF
SUB/CROSSOVER
64
PRESS MUTE TO TEACH
MORE 8
PRESS MUTE TO TEACH
MISC CONTROL
FAVORITE VOLUMES
OPERATE
STANDBY
MUTE ON
VOLUME A: 20.0
VOLUME B: 25.0
VOLUME C: 30.0
VOLUME D: 35.0
VOLUME E: 40.0
MUTE OFF
LATE NIGHT ON
LATE NIGHT OFF
↓ THX ON
ENTER TO SET NEW VOLUME.
ENTER AGAIN TO TEACH
PRESS MUTE TO TEACH
THX OFF
FAVORITE VOLUMES
The Custom Menu
If the setup menu is where you go in order to perform routine setups, the
custom menu is the destination for unusual situations and needs. In many cases,
these needs are the result of the requirements of a custom installation, one in
which home automation equipment may figure heavily. For example, if you want
to control your AVP2 from a centralized controller such as those from
Audioaccess, AMX, Crestron, or Elan, this is the place to come. In this menu you
will find the specific functions you need for systems like these.
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are the owner of the AVP2 (rather than a professional installer), this sec-
tion is likely to be of little interest. It’s the one section you should feel free to
skip entirely. In it, we will cover:
• teaching new IR commands from the AVP2 to a learning remote
control
• programming the two DC “trigger” outputs on the Audio Video
Preamplifier
• the use of the rear panel IR input
• the use of the rear panel RS-232 port
• integrating the AVP2 into a PHAST home automation system
• using the AVP2 with other Madrigal “PHAST-Linked” products
In short, you may have to be a bit of a gearhead to enjoy this section. Feel free to
skip it if this sort of thing puts you to sleep.
teach IR commands The AVP2 itself can transmit all of the IR commands to which it can respond
to your remote from its main display window, enabling you to teach a learning remote both the
standard commands available from the AVP2 remote and a number of other, op-
tional commands which you might find useful.
When using the AVP2 itself to teach new commands to your remote control, your
remote will (obviously) have to be in its learning mode. Therefore, to avoid inad-
vertently learning menu-navigation commands from the AVP2 remote, you must
navigate the on screen menus by using the buttons on the front panel of the
AVP2. The buttons on the front panel you need to use are as follows:
65
• recall: the menu function is provided by the recall button. In order
to activate the on screen menus rather than simply recalling the
calibrated output level settings, press and hold the recall button un-
til the front panel lights are turned off (about ten seconds). From
this point on until you exit the menu system, the recall button will
perform exactly as the menu button on the remote control would.
• volume knob: the front panel volume knob operates in the same
fashion as volume ± buttons on the remote control.
• mute: the enter function is provided by the standby button on the
front panel (when the AVP2 is in menu mode).
1
2
3
ENTER THE SETUP MENU
SELECT “CUSTOM,” AND THEN “TEACH REMOTE”
TO RELEARN THOSE FUNCTIONS WHICH HAVE CORRESPONDING
FRONT PANEL BUTTONS, CHOOSE “PANEL BUTTONS”
The on screen display will prompt you to press any button. Line up the IR
window of the AVP2 remote control with the right side of the main display
of the AVP2, at a distance of approximately 6"-12". Select the to-be-learned
button on the remote, then press the corresponding button on the AVP2.
The display will generate a marquis to let you know that the IR signal has
been transmitted. You may repeat this process until all buttons have been
learned.
To exit, press and hold the recall button (which serves as a menu button
when you use front panel controls within the menu system—merely press-
ing it in this case will result in the recall command being transmitted).
Download from Www.Somanuals.com. All Manuals Search And Download.
4
TO RELEARN BUTTONS WHICH EXIST ONLY ON THE REMOTE CONTROL,
SELECT “REMOTE ONLY”
From the teach remote menu, select remote only. The on screen display
will now look something like this:
remote only menu
REMOTE ONLY
SPECIAL
NEXT VIDEO
PREV VIDEO
NEXT AUDIO
PREV AUDIO
VOLUME UP
↓ VOLUME DOWN
PRESS MUTE TO TEACH
MENU
ENTER
DISPLAY
STATUS
LATE NIGHT
THX TOGGLE
DUAL DRIVE TOGGLE
This menu also scrolls, since there are more commands than will fit in one
screen. Press the appropriate button on your learning remote control (while
in learning mode), and then use the front panel volume knob and mute
button to select and “fire” the appropriate IR command from the main dis-
play of the AVP2 into the remote control. Repeat as necessary.
Most of these commands simply duplicate the corresponding commands on
the AVP2 remote control. The last four provide direct control over four func-
tions normally handled by the special button on the remote:
66
• status
displays the status screen
• late night
• THX toggle
• dual drive toggle
toggles the late night feature on and off
toggles Home THX processing on and off
toggles between dipolar and bipolar re-
sponse in dual drive surround speakers.
5
TO LEARN COMMANDS THAT GIVE DIRECT ACCESS TO SURROUND
MODES, SIGNAL PATHS, “MORE” INPUTS AND POSITIVE CONTROL OVER
TOGGLE FUNCTIONS, SELECT “DIRECT ACCESS” ON THE TEACH REMOTE
MENU
You may also teach special commands to a learning remote control which
allow direct access to the various surround modes, signal path and control
options.
For example, you may find that you use the pro logic II music, stereo sur-
round and surround off modes most frequently. You could assign a button to
each of these and never have to cycle through the other options again. You
could also assign specific output paths to other buttons to allow direct,
“non-toggled” access from the remote control. Another: definite “on” and
“off” commands for standby and mute (rather than toggles) offer improved
control over the AVP2 when operated from a remote zone or as part of an
IR macro.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Note:
All toggled controls (such as “on/off”) on the AVP2 have
positive control alternatives (e.g., “on” and “off” as two
separate commands). This practice supports proper design
and operation of macros. These commands are available in
both IR and RS-232 forms.
The Surround, Path and More Inputs menus under the Direct Access menus
are as follows:
SURROUND MODES
PATH
INPUTS
MORE 1
surround, path and
more inputs menus
SURROUND OFF
MAIN
DOLBY PRO LOGIC
PRO LOGIC + THX
PRO LOGIC II MOVIE
PRO LOGIC II + THX
PRO LOGIC II MUSIC
↓ STEREO SURROUND
REMOTE
BOTH
MORE 2
MORE 3
MORE 4
MORE 5
MORE 6
↓ MORE 7
PRESS MUTE TO TEACH
PRESS MUTE TO TEACH
PRESS MUTE TO TEACH
MONO SURROUND
MONO FRONTS
MONO CENTER ONLY
Use the front panel volume knob and mute button to select and “fire” the
appropriate IR command from the main display of the AVP2 into the learn-
ing remote control. Repeat as necessary.
misc control menus
MISC CONTROL
FAVORITE VOLUMES
67
OPERATE
STANDBY
MUTE ON
VOLUME A: 20.0
VOLUME B: 25.0
VOLUME C: 30.0
VOLUME D: 35.0
VOLUME E: 40.0
MUTE OFF
LATE NIGHT ON
LATE NIGHT OFF
↓ THX ON
PRESS MUTE TO TEACH
THX OFF
FAVORITE VOLUMES
The misc control menu provides positive control commands for functions
that are normally toggled between two states; use the front panel volume
knob and mute button to select and “fire” the appropriate IR commands as
needed.
Favorite volume provides a method for directly accessing any volume set-
ting, something that owners of home automation systems such as
Audioaccess, AMX, Crestron and Elan can use in their macros. For example,
a macro called “Background Music” might be written that would
• select a particular music program on a 100-disc CD changer;
• select cd on the AVP2;
• select Dolby Pro Logic II Music;
• and change the volume setting to 35.0 (regardless of where the
volume had been set previously).
Download from Www.Somanuals.com. All Manuals Search And Download.
Five different volume settings may be stored and recalled directly, without
having to ramp through the intervening volume settings. These favorite vol-
umes may be changed and saved in the usual way; when enter is pressed,
it will both save the change and fire the command for that particular favor-
ite volume.
6
TO LEARN OTHER SPECIAL COMMANDS, SELECT “SPECIAL” ON THE
TEACH REMOTE MENU
Finally, the AVP2 provides several special commands that offer home enter-
tainment enthusiasts and home automation designers more specialized con-
trol over their systems.
SPECIAL
CONTROL TRIGGER 1 ON
CONTROL TRIGGER 1 OFF
CONTROL TRIGGER 2 ON
CONTROL TRIGGER 2 OFF
SUB ON/OFF TOGGLE
PRESS MUTE TO TEACH
Control trigger 1&2 on and control trigger 1&2 off make it possible to con-
trol one or both of the remote turn-on trigger outputs on the rear panel of
the Audio Video Preamplifier independently of the system itself. For ex-
ample, should you decide to use one of these trigger outputs to control am-
plifiers in the remote zone rather than the local amplifiers, learning these IR
commands would allow you to turn the remote amplifiers on and off (even
from across the house) without affecting the operational status of the main
home theater.
68
The sub on/off toggle feature will toggle between the configuration estab-
lished during initial setup and using the front three loudspeakers full-range,
without any help from the subwoofer(s). (Specifically, it turns off the cross-
over and the subwoofer output when sub/crossover off is selected.) This fea-
ture may be used to compare the performance of the system configured
with and without the subwoofer(s). (Note that pressing recall will always
return the system to its calibrated setup configuration, regardless of its cur-
rent status.)
trigger settings Having gotten through the nearly endless teach remote capabilities of the AVP2,
the remainder of the custom menu is used to configure how the AVP2 communi-
cates with other products. When you enter this menu, you see something like
this:
CUSTOM
TEACH REMOTE
TRIG 1 SOURCE: STANDBY
TRIG 1 TYPE: PULSE
TRIG 2 SOURCE: STANDBY
TRIG 2 TYPE: LEVEL
REAR IR IN: REMOTE
MP-8/9 LINK: ON
LINK MASTER: ON
Download from Www.Somanuals.com. All Manuals Search And Download.
A trigger source refers to what the trigger takes it cue from: either the system
changing back and forth from standby to operate, or an independent
IR command (learned in the teach remote menu). Each of the two hardware
triggers may be set independently of the other.
The type refers to whether the output of the trigger is a level (constant) trigger
or a pulse (simulating the action of a momentary-closure contact switch). The
vast majority of trigger-compatible equipment on the market today is looking for
a level (continuous when “on”) trigger; the pulse option is provided for the occa-
sional exception to this rule.
Internal settings within the Audio Video Preamplifier determine whether the elec-
trical result of these triggers is a nominal 5V or 12V, or even the closing of a dry
contact relay (should you require to source more current or a higher voltage than
the Audio Video Preamplifier can provide). If this last is the case, you can use
control trigger 1 as a switch by placing it in series with an external power source
such as a “wall wart” power supply.
The default settings from the factory are as follows:
• trigger 1 = 12V level when not in standby (0V when in standby)
• trigger 2 = 12V level when not in standby (0V when in standby)
The three switches that determine what combination of 5V, 12V or relay your
AVP2 uses are located inside your AVP2 and must be set by a qualified installer.
Warning!
There are no user serviceable parts inside the AVP2!
If you need one of the internal settings changed to support
your installation, please contact your dealer.
69
rear ir input menu The infrared remote input jack on the rear panel of the AVP2 may be pro-
grammed to respond to either local commands (e.g., duplicating the functionality
of the IR receiver in the AVP’s main display) or remote commands (e.g., from an
IR repeater, intended to affect only the remote signal path). (Refer to the Remote
IR and Remote Turn-on section of your AVP2 manual for more information.)
The factory default setting is remote. If your installation of the AVP2 prevents IR
commands from reaching the AVP2 (as when behind closed doors, for example),
and if you are using an IR repeater to pass IR commands to the system, you may
wish to set the IR input on the rear panel to local, in which case you would also
want to “hard-wire” the AVP2 to your IR repeater. To make this software change,
follow these steps:
1
2
ENTER THE CUSTOM MENU
This menu is accessed from the main menu by moving the cursor to
custom, and pressing enter to select the menu item.
SELECT REAR IR INPUT
Using the volume ± buttons, move the cursor to rear IR input and press
enter.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
TOGGLE THE MENU ITEM FROM REMOTE TO LOCAL
Press either of the volume ± keys to change the default setting of remote to
local. Press enter to save the change.
MP-8/9 Link The AVP2 has the ability to control the operational status of the Madrigal Imaging
MP-8 and MP-9 video projectors in an intelligent fashion.
Specifically, when the MP-8/9 Link is turned on and the AVP2 is connected to
either an MP-8 or an MP-9 projector, the AVP2 can toggle the projector between
its operate and standby conditions according to whether an A/V source has been
selected on the AVP2. (There is a short delay prior to changing the state of the
projector, to guard against rapid toggling of the projector’s status when acciden-
tally selecting an incorrect input.)
To take advantage of this feature with your Madrigal Imaging projector:
1
2
TOGGLE THE MP-8/9 LINK TO “ON”
CONNECT EITHER PHASTLINK™ CONNECTOR ON THE REAR PANEL OF
THE AVP2 TO THE CORRRESPONDING PHASTLINK™ INPUT CARD ON THE
PROJECTOR
Use a “straight-through” eight-conductor cable terminated in RJ-45 connec-
tors. This cable is outlined on page 29, in PHASTLink™ Control Ports.
Link Master When using the AVP in a PHAST™ home automation system, the PHAST™ con-
troller (that is, the computer running the PHAST™ software) must be the “master”
of the communications bus. It is responsible for passing all communications be-
tween various components in the system, much as the Post Office sorts out and
delivers the mail.
70
However, many Madrigal products also use the PHAST™ communications hard-
ware for their own inter-component communications, even absent the PHAST™
controller. In these cases, one of the Madrigal products serves as the “master” of
the communications bus, facilitating all the communications between the various
components. In effect, absent a post office, one of the Madrigal products steps in
to deliver the mail.
At the risk of excessive anthropomorphizing, PHAST™ controllers do not like
such challenges to their authority. To prevent the AVP2 from attempting to be-
come the “master” of the communications bus when sharing it with a PHAST™
control system, we suggest toggling the Link Master menu item to off, which pre-
vents the AVP2 from even enquiring as to whether it might take on these respon-
sibilities. If you do not have a PHAST™ controller, you may safely ignore this
menu item and leave it in its on setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
The About… Menu
ABOUT...
BOOT CHECKSUM
XXXX
PROC1 CODE: XXXXXXXX
PROC1 VERSION: XXX
PROC2 VERSION: XXXX
PROC3 VERSION: XXXX
This screen displays checksum information about the version of the software
your system is using, and will be tremendously helpful if you ever have a prob-
lem and need to call for technical support.
Please copy these numbers down for future reference in the back of this manual
under Your System Settings. Also, update your copied information whenever you
receive a software update from your dealer. That way, you will be able to take the
numbers to the phone with you if you have to call.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Special Menu
The AVP2 remote control includes a button labelled special which can serve a
variety of functions, depending on your personal preferences. To access the full
list of features controlled by this single button, press and hold the special button
on the remote control for several seconds, until the special key actions menu
appears on screen.
special key actions menu
SPECIAL KEY ACTIONS
STATUS DISPLAY
THX TOGGLE
CENTER LEVEL
SURROUND LEVEL
SUB LEVEL
SUB TOGGLE
BALANCE
OFF
O.O
O.O
O.O
ON
LATE NIGHT TOGGLE: OFF
DISPLAY INTENSITY: HIGH
You can move the cursor up or down the list of functions using the volume ± key
on the remote. Having selected the item you wish to control, either
• press special again to exit the menu without activating the feature
(that is, leaving it the way it is)
72
• press enter to both exit the menu and execute the feature
For example, if you frequently watch movies and wish to have one-button access
to a THX control that will toggle between THX on and THX off, enter the spe-
cial key action menu and leave the cursor arrow beside thx toggle: off. Pressing
special again will leave THX off, and subsequent clicks of the special button will
toggle THX on and off without having to enter the menu. Alternatively, you could
pressing enter to exit the menu and turn THX on (in this example).
Similarly, you can
• adjust the relative volume of the center, rear, and sub channels
• toggle your sub on and off (with your front L&R speakers tempo-
rarily changing to “full range” when the subwoofer is “off”)
• adjust the left/right balance
• toggle late night AC-3 compression on and off, and
• cycle through the available display intensities as you would from
the front panel display intensity button.
The status display feature, when selected, will display a comprehensive list of
information pertaining to the current status of the AVP2. Although the specifics
will change as to reflect whatever is currently being done by the AVP2, the screen
will looks something like the following:
Download from Www.Somanuals.com. All Manuals Search And Download.
sample status display screen
SOURCE: DVD
SIGNAL: 3+2+1
MODE: DOLBY DIGITAL
RATE: 384k
SUB: ON
VOLUME: 65.0
MIGRATION: AUTO
RECORD INFO: NOT LOCKED
This screen is particularly helpful if you need to do any troubleshooting in the
system, as it will tell you exactly what sort of signal is being received by the
AVP2 and what is being done with it.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the AVP2
setting the volume Normally, when you wish to change the volume, you want all the speakers to
move up or down together, maintaining their relative balance. Thus the volume
control (either front panel knob or remote control button) will operate as a mas-
ter volume by default.
Occasionally, you may want to change the volume of some speakers relative to
others; for example, you may want to increase the level of the rear speakers a bit
for more dramatic surround effects. To do so, press the rear button, then make
your volume change while the light about the rear button is still lit. Similar two-
step operations work for center, subwoofer and balance as well.
If you have made a relative adjustment and wish to adjust the master volume
without waiting for the system to timeout and return to its default, pressing mas-
ter will allow you to immediately adjust the master volume.
surround off The surround off mode is intended for music reproduction without any form of
surround enhancement. In this mode, the Left and Right speakers are active along
with the subwoofer(s), and reproduce the input without any processing other
than the electronic crossover needed for the subs.
74
THX Ultra® THX Ultra® indicates that the proprietary Home THX audio processing circuits are
in use in addition to whatever multichannel audio is appropriate for the source in
question. This can include Dolby Digital, DTS, or Dolby Pro Logic (either I or II).
In the case of discrete multichannel sources (anything other than Pro Logic),
THX 5.1 will be employed automatically when the THX cinema mode is en-
gaged; in the case of Pro Logic, THX 4.0 is used.
THX is most appropriate for film-based program materials made since the mid-
1970’s, which have (in all likelihood) been mixed in a standard dubbing stage
environment. This setting will provide the listener with the most accurate repro-
duction of the majority of motion pictures available. In addition, many other
video source materials are produced in Dolby Surround using the industry stan-
dard response curves, and are best enjoyed in the THX mode. (Examples include
Star Trek: Enterprise and The David Letterman Show, which are mixed in an envi-
ronment which emulates the dubbing stage used for film.)
THX includes several specific technologies designed to more accurately reproduce
film soundtracks:
• Re-Equalization™: corrects for the overly bright front channels
commonly found in film soundtracks
• Electronic Crossover: designed to work optimally with THX-
certified speakers to enhance low frequency dynamic range (espe-
cially important with multichannel digital sources such as Dolby
Digital and DTS)
• Adaptive Decorrelation™: enhances surround spaciousness and
envelopment only when necessary (based on the soundtrack itself)
• Bass Peak Level Manager™: keeps low frequency transients un-
der control to minimize the opportunity for amplifier or speaker
Download from Www.Somanuals.com. All Manuals Search And Download.
overload.
• Loudspeaker Position Time Synchronization™: ensures a
coherent, time-aligned soundfield.
When in doubt as to whether THX processing should be included, listen for a
natural presentation of the treble. Films mixed for theatrical release exhibit an el-
evated treble region when played back on a home system with flat response. The
THX mode will correct this. Conversely, surround-encoded programs without this
high frequency emphasis might sound dull or lacking in detail when (incorrectly)
played in the THX mode.
Dolby Digital The AVP2 automatically detects Dolby Digital 5.1 channel recordings and decodes
them appropriately to give you five discrete channels of information plus a Low
Frequency Effects (LFE) channel. This LFE channel is sometimes called the “.1”
channel, due to its limited bandwidth as compared to the other channels, all of
which are full range.
The sophisticated bass management provisions in your AVP2 takes these five full
range signals plus the deep bass information in the LFE channel, and redirects all
this information to whatever speakers can actually reproduce it. Bass management
both ensures that you can actually hear what you were intended to hear, and sig-
nificantly reduces distortion that likely would result otherwise from bass-limited
speakers being overloaded by deep bass they were never intended to reproduce.
The result is cleaner, more full-bodied sound than would otherwise be available
from most systems.
75
Dolby Digital Surround EX The AVP2 also automatically detects Dolby Digital Surround EX recordings. Sur-
round EX recordings have a sixth, “center back” channel “hidden” in the two dis-
crete surround channels, along with a “flag” in the identify the signal to the pro-
cessor. For this reason, Surround EX is sometimes called a “6.1 channel” system. It
may be used with 5.1, 6.1, or 7.1 channel speaker systems.
If you have both surround and either one or two rear channels defined in your
speaker configuration, the AVP2 will retrieve this “extra” information and send it
to the appropriate speaker(s). If you do not have surround and rear speakers, this
“extra” information is folded into the existing surround speakers so you can still
hear it, though of course it may not image exactly as intended (since you lack
the extra speakers.)
The sophisticated bass management provisions in your AVP2 takes these five, six,
or seven full range signals plus the deep bass information in the LFE channel,
and redirects all this information to whatever speakers can actually reproduce it.
Bass management both ensures that you can actually hear what you were in-
tended to hear, and significantly reduces distortion that likely would result other-
wise from bass-limited speakers being overloaded by deep bass they were never
intended to reproduce. The result is cleaner, more full-bodied sound than would
otherwise be available from most systems.
DTS The AVP2 automatically detects DTS 5.1 channel recordings and decodes them
appropriately to give you five discrete channels of information plus a Low Fre-
quency Effects (LFE) channel. This LFE channel is sometimes called the “.1” chan-
nel, due to its limited bandwidth as compared to the other channels, all of which
are full range.
Download from Www.Somanuals.com. All Manuals Search And Download.
The sophisticated bass management provisions in your AVP2 takes these five full
range signals plus the deep bass information in the LFE channel, and redirects all
this information to whatever speakers can actually reproduce it. Bass management
both ensures that you can actually hear what you were intended to hear, and sig-
nificantly reduces distortion that likely would result otherwise from bass-limited
speakers being overloaded by deep bass they were never intended to reproduce.
The result is cleaner, more full-bodied sound than would otherwise be available
from most systems.
DTS-ES Matrix DTS-ES Matrix is conceptually very similar to Dolby Digital Surround EX. It em-
beds an extra, “center back” channel of surround information within the existing
two discrete channels of surround, to be extracted by the AVP2 upon playback.
For this reason, DTS-ES Matrix is sometimes called a “6.1 channel” system. It may
be used with 5.1, 6.1, or 7.1 channel speaker systems.
If you have both surround and either one or two rear channels defined in your
speaker configuration, the AVP2 will retrieve this “extra” information and send it
to the appropriate speaker(s). If you do not have surround and rear speakers, this
“extra” information is folded into the existing surround speakers so you can still
hear it, though of course it may not image exactly as intended (since you lack
the extra speakers.)
The sophisticated bass management provisions in your AVP2 takes these five, six,
or seven full range signals plus the deep bass information in the LFE channel,
and redirects all this information to whatever speakers can actually reproduce it.
Bass management both ensures that you can actually hear what you were in-
tended to hear, and significantly reduces distortion that likely would result other-
wise from bass-limited speakers being overloaded by deep bass they were never
intended to reproduce. The result is cleaner, more full-bodied sound than would
otherwise be available from most systems.
76
DTS-ES Discrete DTS-ES Discrete is is yet another 6.1 channel system, but it differs in one impor-
tant way from both Dolby Digital Surround EX and DTS-ES Matrix. It includes an
entirely separate sixth, “center back” channel of surround information in the sig-
nal being sent to the AVP2 for decoding (rather than “hiding” the information
within the other surround channels). This approach provides essentially perfect
separation between the various channels of audio, whereas the other two ap-
proaches to 6.1 channel sound are somewhat limited in their potential separation.
It may be used with 5.1, 6.1, or 7.1 channel speaker systems.
If you have both surround and either one or two rear channels defined in your
speaker configuration, the AVP2 will retrieve this “extra” information and send it
to the appropriate speaker(s). If you do not have surround and rear speakers, this
“extra” information is folded into the existing surround speakers so you can still
hear it, though of course it may not image exactly as intended (since you lack
the extra speakers.)
The sophisticated bass management provisions in your AVP2 takes these five, six,
or seven full range signals plus the deep bass information in the LFE channel,
and redirects all this information to whatever speakers can actually reproduce it.
Bass management both ensures that you can actually hear what you were in-
tended to hear, and significantly reduces distortion that likely would result other-
wise from bass-limited speakers being overloaded by deep bass they were never
intended to reproduce. The result is cleaner, more full-bodied sound than would
otherwise be available from most systems.
Download from Www.Somanuals.com. All Manuals Search And Download.
dolby pro logic Some two-channel program material does not conform to film industry standards,
although it may still be Dolby Surround encoded so it can decode to four chan-
nels. Music videos on MTV, for instance, are often Dolby Surround encoded, but
have soundtracks which are produced in non-film studios. In fact, hundreds of
music CDs are mastered with surround sound. These sources and others which
have surround encoding but which are unlikely to have been mixed or remixed
in industry-standard production facilities should use the pro logic mode to avoid
compensation where none is indicated.
dolby pro logic II Recently, Dolby Laboratories introduced a newly-designed process for playing
back both encoded and non-encoded material. Called Dolby Pro Logic II, it deliv-
ers a level of performance from encoded materials that is much closer to the
sound we have become accustomed to from discrete multichannel soundtracks
like Dolby Digital and DTS, even from older, “legacy” films in which those more
advanced soundtracks were not an option.
There are two basic versions of Dolby Pro Logic II, one optimized for Dolby Sur-
round-encoded movies, and the other optimized for non-encoded music material
(your entire CD collection, for example).
Dolby Pro Logic II Movie is available either with or without the THX post-pro-
cessing described above. Compared to the original Pro Logic, you can enjoy im-
proved separate between channels for improved localization and spaciousness.
Dolby Pro Logic II Music is not available with THX post-processing (since THX
was designed to correct film-specific problems), but offers surprisingly convincing
surround sound performance from normal stereo recordings.
77
stereo surround The stereo surround mode has been carefully designed to extract real ambience
from your recordings rather than synthesizing something artificial that might be
quite alien to the music itself. The ambient cues found in the program material
are then used to provide appropriate information for the center and rear speakers.
The front Left and Right speakers are left unaffected by this mode, allowing you
to hear unadulterated stereo imaging with the addition of a genuine sense of hall
ambience. In general, it tends to be somewhat more subtle than Dolby Pro Logic II
Music—which you prefer is a matter of taste, and may vary from one recording
to the next.
Since this mode is based on the recordings themselves, it is normal to hear some
variation in the degree of the effect. Extremely “dry” recordings which lack any
significant ambience may not sound significantly different than when in surround
off mode (e.g., two-channel stereo). You may find that increasing the level of the
rear speakers is necessary in order to bring what little ambience is in a “dry” re-
cording up to a more enjoyable level.
mono surround The mono surround mode can provide a sense of spaciousness and size to
monophonic program material such as some historical recordings and movie clas-
sics such as Casablanca or The Wizard of Oz.
The mono surround mode makes no effort to “electronically reprocess to simulate
stereo” (a process which almost always causes more harm than good). Instead, it
uses sophisticated steering techniques to create a sense of space in what would
otherwise be a largely dimensionless soundfield. It is particularly helpful when
Download from Www.Somanuals.com. All Manuals Search And Download.
viewing mono program material on a big screen, where a tiny mono image
would simply sound wrong in contrast to the big picture.
mono on fronts The AVP2 also includes the option of playing mono signals through all three front
speakers. The mono on fronts sound is somewhat “smaller” than that provided by
the mono surround mode, but one that is still larger than playing the mono signal
only through the center channel speaker.
mono center only The mono center only mode sums the incoming Left and Right signals. The re-
sult is sent to the center channel speaker only. This mode is especially useful for
older, classic films or historical recordings which have noisy mono soundtracks.
Since much of the noise is likely to be random in phase, significant noise cancel-
lation can often be achieved by playing these mono sources in a true mono
mode.
automatic migration If you have multiple connections defined for a particular source, the AVP2 will
automatically use the highest-priority connection available. For example, if you
have chosen AC-3 RF demodulator, followed by digital, followed by analog for
your laserdisc player, the system will first look to the RF input. If it cannot lock
onto a signal there, it will move to the digital input. Lacking a signal there, it will
migrate to the analog input. In fact, within limits, the system will continue to look
for a higher-priority signal and if one becomes available, will go to it automati-
cally. (The exception is auto-migration away from an analog input, which is im-
possible for technical reasons.)
78
If you have the on screen messages enabled, you will be notified of auto migra-
tion changes.
At your option, automatic migration may be turned off (in the Operate menu).
For most people, it is easier to use “forced migration” when they want to see
what a different connection might sound like, as explained below.
forced/manual migration On some occasions, you may wish to “force” a migration beyond the usual prior-
ity. In our laserdisc case, for example, you might want to compare the sound
quality of Dolby Digital to (digital) Pro Logic, and to (analog) Pro Logic in the
AVP2. To do so, simply click the source button again (in this case, laserdisc) for
each forced migration. The system will cycle through all available connections.
Note that when you have done this, you have asked the system to migrate from
one input to the next manually. To restore automatic migration, simply select any
other input button (assuming that automatic migration is turned on in the oper-
ate menu).
watching a simulcast To create a “simulcast” situation wherein you are watching the video associated
with an A/V source button, with the audio associated with an audio-only source
button, simply select the picture you want followed by the sound you want, in
turn. In this way, you can watch a sporting event while listening to the play by
play on the radio (for example). Note that you must have simulcast: on in the
operate menu.
To return to the usual combination of audio and video from the same source,
simply reselect that (or any other) A/V source. If using the remote control, a
Download from Www.Somanuals.com. All Manuals Search And Download.
single touch of either side of the video ± button will return you to the original
A/V source’s audio as well as it’s video.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
System Planning Guide
Experience shows that almost any reasonable amount of time spent in the plan-
ning stages will pay for itself two to three times over during the installation—
more if the installation crew includes two or three people. With the background
provided in the previous sections, the planning process can be boiled down to a
checklist which will ensure that you do not overlook anything important.
video placement
✓ The primary seating area should be perpendicular to the picture.
✓ Be aware of the trade-off between screen size and perceived clar-
ity. The resolution of NTSC requires a seating distance of at least 4
times the diagonal screen size for maximum perceived clarity (this
is why small screens seem so sharp). Yet larger images have greater
visual impact. You may want to go for a seating distance of as little
as 2 times the screen size to increase visual involvement (although
this is probably only realistic if you have a line-doubled digital
television).
✓ Stray ambient light should be minimized. (Drapes, dimmers, light
placement)
✓ Leave room for the Left, Center, and Right (LCR) speakers up front,
flanking the screen itself, placed with reasonable symmetry with
respect to adjacent walls, and all at the same distance from the pri-
mary viewing area.
✓ The screen should be well away from side walls, since you want to
minimize side wall reflections from the front (LCR) speakers.
80
electronics placement
✓ Cabinetry is generally preferred to conceal the distracting LEDs on
the equipment. (An infrared repeater system may be needed in
this case.)
✓ The ideal system would have invisible, yet readily accessible equip-
ment and an IR repeater to relay the user’s commands from the
area of the screen to the concealed electronics.
✓ People tend to aim their remote controls at the screen, regardless
of where the equipment is. In the absence of IR repeaters, placing
the electronics near the screen makes the system’s operation more
intuitive.
✓ Ample ventilation for the power amplifiers must be provided, pref-
erably through convection (to avoid fan noise).
speaker placement
✓ Can the speakers be used as designed? (Wall-mounting speakers
designed to be used in free space may create a mid-bass bump in
the response—consult with the manufacturer of your speakers as
to their best use.)
✓ The Left and Right speakers often should be closer to the edges of
the screen than you may think best initially. There is some cogni-
tive dissonance (disorientation) when sound appears to come from
well away from its apparent visible source.
✓ The Center speaker should be centered on the screen, directly
above or below it (unless you have an acoustically transparent
screen, in which case it may be directly behind the center of the
screen). Try to keep its tweeters as close to the level of the tweet-
ers in the L&R speakers as possible, so that pans do not involve
noticeable changes in altitude. Make sure that the Center speaker is
Download from Www.Somanuals.com. All Manuals Search And Download.
the same distance from the main listening area as the Left and
Right speakers.
✓ If THX-certified LCR speakers are used and must be either above
or below ear level when seated, aim them down (or up) into the
listening area. They are intentionally quite directional in the vertical
plane, to improve dialog intelligibility and localization.
✓ Placing the LCRs below the screen is generally preferable to place-
ment above.
✓ The subwoofers do not have to be extremely close to the LCRs, but
placement will affect the quality and consistency of the low bass.
Experimentation is in order.
✓ Dipolar surrounds should be located high and to the sides of the
listeners instead of behind them, in order to place the audience in
the surround speakers’ null. If the viewing area is more than one
row deep, place the surrounds halfway back within the seating
area.
✓ If architectural constraints prevent ideal placement of dipolar sur-
rounds directly to the sides of the listening area, it is generally best
to err on the side of being a bit further to the rear of the room.
✓ When using traditional speakers for the surround channels, the
speakers should be located high and somewhat behind the listen-
ers, with the speakers’ output directed toward the rear wall rather
than at the listeners.
✓ The surrounds should be relatively high, often near the ceiling for
the best results. And they should be located equally distant from
their adjacent walls/ceilings, or else one will have more mid-bass
than the other.
81
additional notes on
speaker placement
• Some allowance must be made for those installations involving
relatively small screens, such as 35" direct-view televisions. Placing
the speakers immediately beside televisions of this size may reduce
the stereo separation to unacceptable levels. Some experimentation
is in order, but as a rule of thumb, try to have the L and R speakers
spread apart by no more than approximately 1.5 times the width of
the screen to avoid cognitive dissonance from the apparent conflict
between visual and aural images.
• With regard to subwoofer placement, it is important to leave your-
self some leeway during final installation for minor movements to
minimize the effects of room modes. Corner placement usually
works best, but not always—you have to try it in your particular
situation to be sure.
• Use multiple subwoofers if more bass output is needed. This also
has the advantage of allowing one subwoofer to fill the other’s
“holes” created by room modes, while reducing distortion by giving
each subwoofer an easier task.
Download from Www.Somanuals.com. All Manuals Search And Download.
Your System Settings
The settings in your Proceed AVP2 are saved in nonvolatile memory and should
normally survive power outages. Still, it is a good idea to write your preferred
settings down against the chance of an inquisitive neighbor or family member
changing them without your knowledge. Please use the following form to record
your system’s settings against such a possibility.
the about… menu
• Boot Checksum:
______
• Processor 1 Code: ______
• Processor 1 Version: ______
• Processor 2 Version: ______
• Processor 3 Version: ______
operate menu settings
• Display Position
______
• On Screen Status Yes or No (circle one)
• Status Preferences:
source info
format info
on or off (circle one)
on or off (circle one)
mode info
on or off (circle one)
THX info
on or off (circle one)
sub info
on or off (circle one)
volume info
migration info
record info
on or off (circle one)
on or off (circle one)
on or off (circle one)
82
• Display Timeout
• Character Style
1 2 3 4 5 seconds (circle one)
Normal or Black Box (circle one)
• Background Color Blue, Green or Grey (circle one)
• Volume display
Relative (to THX reference level) or
Absolute (with 0.0 representing volume off)
Slow or Fast (circle one)
______
• Volume Speed
• Mute level
• Maximum Volume ______
• Late Night
low or high (circle one)
• Auto Migration
• Simulcast
• Setup:
on or off (circle one)
on or off (circle one)
Unlocked or Locked
(after you re-enter all other settings)
Download from Www.Somanuals.com. All Manuals Search And Download.
vcr 1 button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
disc 1 button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
83
vcr2/disc2 button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
Download from Www.Somanuals.com. All Manuals Search And Download.
tv/aux button defaults
satellite button defaults
cd button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
84
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
Download from Www.Somanuals.com. All Manuals Search And Download.
tape button defaults
aux button defaults
tuner button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
85
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
Download from Www.Somanuals.com. All Manuals Search And Download.
more 1 button defaults
more 2 button defaults
more 3 button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
86
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
Download from Www.Somanuals.com. All Manuals Search And Download.
more 4 button defaults
more 5 button defaults
more 6 button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
• Audio Connectors ______
• 1:
• 2:
• 3:
• Input Offset
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
(1, 2, or 3)
____________________________
____________________________
____________________________
______
87
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
Download from Www.Somanuals.com. All Manuals Search And Download.
more 7 button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
more 8 button defaults
• Name
• Type
• Video
• 2-ch
______
Audio, A/V or Unused
____________________________
Pro Logic II Music, Pro Logic II + THX,
Pro Logic II Movie, No Change, Pro Logic + THX,
Pro Logic, 2-ch/Surround Off, No Change, Mono Fronts,
Mono Center Only, Mono Surround, Stereo Surround
(circle one)
• Multi-ch THX:
• Record Device:
Force On, Force Off, Use Defaults
Prohibit, Warning, No (circle one)
• Audio Connectors ______
(1, 2, or 3)
88
• 1:
• 2:
• 3:
• Input Offset
____________________________
____________________________
____________________________
______
crossover settings
• Front L&R
• Center
• Surrounds
• Subs
• Aux 1
• Aux 2
Full Range, or ___ Hz
Full Range, ___ Hz or None
Full Range, ___ Hz or None
Full Range, 80 Hz LPF or None
Right Back, R. Dual Drive, Center Back, or Not Used
Left Back, L. Dual Drive, L. Stereo Sub, Extra Mono Sub,
or Not Used
set distance
• Left
______
• Center
• Right
______
______
• R. Surround
• R. Back
• L. Back
• L. Surround
• Sub
______
______
______
______
______
• Units
English or Metric (circle one)
Download from Www.Somanuals.com. All Manuals Search And Download.
set levels
• Left
• Center
• Right
• R. Surround
• R. Back
• L. Back
• L. Surround
• Sub
______
______
______
______
______
______
______
______
bass level manager
• Saved level
______
surround mode defaults:
dolby digital
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
surround mode defaults:
dts
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
89
surround mode defaults:
mpeg
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
surround mode defaults:
pro logic
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
surround mode defaults:
pro logic + THX
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
Download from Www.Somanuals.com. All Manuals Search And Download.
surround mode defaults:
stereo surround
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
surround mode defaults:
mono surround
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
surround mode defaults:
2-ch/surround off
• Center
• Surround
• Sub
______
______
______
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
surround mode defaults:
mono
• Center
• Surround
• Sub
______
______
______
90
• Sub Mode
• THX
No Change, Force on, Force Off, Extra Bass (circle one)
On, Off (circle one)
• Dual Drive
Bipole, Dipole (circle one)
control trigger 1
control trigger 2
• Source:
• Type:
Standby or Infrared Command (circle one)
Pulse or Level (circle one)
• Source:
• Type:
Standby or Infrared Command (circle one)
Pulse or Level (circle one)
rear ir in
MP-8/9 Link
Link Master
• Rear IR Input:
• MP-8/9 Link:
• Link Master:
Remote or Local (circle one)
on or off (circle one)
on or off
(circle one)
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Your Proceed Audio Video Preamplifier has been designed to deliver many years
of satisfaction. It has also been designed to allow an unusual amount of
“customization” so as to make it suitable in a wide variety of (possibly changing)
circumstances. This flexibility necessitates a certain amount of setup before the
unit can be expected to perform correctly—in effect, one must inform the system
of its environment so it may make the right “decisions” about what it should do.
Once setup is completed, the system is quite simple to use. But the setup is quite
essential.
It has been our experience that most difficulties encountered with the AVP2 are
due to improper initial setup. Please review the relevant portions of this manual
for the details of the setup procedure.
THERE SEEMS TO BE TOO LITTLE (OR TOO MUCH) BASS.
✓ Is the low frequency cutoff set correctly for your speakers?
✓ Are the output levels set accurately, using a dB SPL meter?
✓ Are all the loudspeaker phased properly with respect to one an-
other?
THE AURAL IMAGE SEEMS INCONSISTENT OR VAGUE
✓ Are all the loudspeaker phased properly with respect to one an-
other?
91
✓ Are the output levels set accurately, using a dB SPL meter?
✓ Are your speakers closely matched to one another in tonal balance
and dynamic performance?
THERE IS A PERSISTENT HUM IN THE SPEAKERS.
✓ If it exists only with a particular input, check that source compo-
nent and its interconnecting cables.
✓ If it exists on all sources, you may have a ground loop by having
multiple ground references in your system. We suggest you ask
your dealer for assistance in isolating this problem.
MY ON SCREEN DISPLAY HAS INDICATED THAT IT HAS DETECTED
POTENTIAL AC PROBLEMS AND REFERRED ME TO THIS SECTION OF THE
MANUAL.
✓ If this is the first time you have seen the message, you probably
don’t have to do anything. If the system detects an electrical prob-
lem that might affect its operating software (an unusually strong
spike on the AC line, for example), it posts this message and
reinitializes itself automatically. Your user settings, output levels and
so forth are retained.
✓ If you see this message with any regularity, you may have a persis-
tent, severe ground loop or other AC problem that should be fixed.
We suggest you ask your dealer for assistance in isolating and solv-
ing this problem.
Download from Www.Somanuals.com. All Manuals Search And Download.
I LEFT THE SYSTEM ON, BUT JUST RETURNED AND FOUND IT IN STANDBY.
WHAT IS HAPPENING?
✓ There was probably a power outage while you were away from the
system. During a power failure, the AVP2 saves all of its critical set-
tings to nonvolatile memory. When power is restored, it enters the
standby mode and waits for your return.
MY VIDEO IS SOMETIMES WASHED OUT, APPEARING IN BLACK AND
WHITE ONLY. WHAT GIVES?
✓ Cause: The AVP2 can do a full conversion from S-video to com-
posite, making all of the S-video sources available to the composite
outputs of the AVP2 (both main and remote/record). This often
simplifies operation significantly. However, conversion in the other
direction would have added significantly to the cost of the AVP2.
Instead, you get a black and white only rendition of whatever you
are trying to watch if you try to monitor a composite source on the
S-video output.
✓ What to do: switch to the S-video input on your TV. Assuming it
is connected, you’ll get all of the picture—color as well as black
and white.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
To remove dust from the cabinet of the Audio Video Preamplifier, use a feather
duster. To remove dirt and fingerprints, we recommend isopropyl alcohol and a
soft cloth.
Caution!
Always apply the isopropyl alcohol to the soft cloth and then
wipe the Audio Video Preamplifier with the dampened cloth.
Never pour or spray even small amounts of any liquid directly
on the Audio Video Preamplifier, as doing so may allow the
liquid to reach the circuitry inside the unit. Any liquid inside
the unit poses a hazard to both the user and to the unit, and
must be avoided.
When the Remote Control’s batteries need to be replaced, use only AA batteries;
always replace both batteries at the same time. If you don’t plan to use the Re-
mote Control often, remove the batteries. When not used for an extended period,
even “leakproof” batteries can leak corrosive acids that will damage the Remote
Control (and will void the warranty on the remote control).
93
Download from Www.Somanuals.com. All Manuals Search And Download.
U.S. and Canadian Warranty
90-day limited warranty This Proceed® product is warranted to be free from defects in material and work-
manship under normal use for a period of ninety (90) days from the date of pur-
chase. To extend the warranty of this Proceed product, return the warranty registra-
tion card along with a copy of the original receipt of purchase to Madrigal, Inc.,
P. O. Box 781, Middletown, CT 06457.
Alternatively, you may extend your warranty by registering your new Proceed
product online at
http://www.madrigal.com/madrigal_warranty3.asp
There is also a link to this warranty registration form on the Madrigal home page,
at http://www.madrigal.com/. (This may save you some typing.)
five year extended warranty The extended warranty for this Proceed product is five (5) years from the date of
purchase. During the warranty period, any Proceed component exhibiting defects
in materials and/or workmanship will be repaired or replaced, at our option,
without charge for either parts or labor, at our factory. The warranty will not apply
to any Proceed component that has been misused, abused or altered.
Any Proceed component not performing satisfactorily may be returned to the fac-
tory for evaluation. Return authorization must first be obtained by either calling
or writing the factory prior to shipping the component. The factory will pay for
return shipping charges only in the event that the component is found to be de-
fective as above mentioned. There are other stipulations that may apply to ship-
ping charges.
94
There is no other express warranty on this component. Neither this warranty nor
any other warranty, express or implied, including any implied warranties of mer-
chantability or fitness, shall extend beyond the warranty period. No responsibility
is assumed for any incidental or consequential damages. Some states do not al-
low limitations on how long an implied warranty lasts and other states do not
allow the exclusion or limitation of incidental or consequential damages, so that
the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. This warranty is applicable in the United States and
Canada only. Outside of the U.S. and Canada, please contact your local, autho-
rized Proceed distributor for warranty and service information.
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining Service
We take great pride in our dealers. Experience, dedication, and integrity make
these professionals ideally suited to assist with our customers’ service needs.
If your Proceed component must be serviced, please contact your dealer. Your
dealer will then decide whether the problem can be remedied locally, or whether
to contact Madrigal for further service information or parts, or to obtain a Return
Authorization. The Madrigal Technical Services Department works closely with
your dealer to solve your service needs expediently.
Important!
Return authorization must be obtained from Madrigal’s
Technical Services Department BEFORE a unit is shipped for
service.
It is extremely important that information about a problem be explicit and com-
plete. A specific, comprehensive description of the problem helps your dealer and
the Madrigal Technical Services Department locate and repair the difficulty as
quickly as possible.
A copy of the original bill of sale will serve to verify warranty status. Please in-
clude it with the unit when it is brought in for warranty service.
95
Warning!
All returned units must be properly packaged (preferably in
their original packing material), and the proper return
authorization numbers must be marked on the outer carton
for identification. If the packaging to protect the unit is, in our
opinion or that of our dealer, inadequate to protect the unit,
we reserve the right to repackage it for return shipment at the
owner’s expense. Neither Madrigal nor your dealer can be
responsible for shipping damage due to improper (that is,
non-original) packaging.
Your dealer can order a new set of shipping materials for you if you need to ship
your component and no longer have the original materials. There will be a
charge for this service. We strongly recommend saving all packing materials in
case you need to ship your unit some day.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
✓ Frequency response:
20 Hz – 20 kHz, +0dB, –0.2dB
0.005% @ 1 kHz, A-weighted
10 V rms
✓ Total harmonic distortion:
✓ Maximum output (XLR):
✓ Maximum output (RCA):
✓ Dynamic range:
✓ Signal to noise ratio (balanced outputs):
✓ Channel separation:
5 V rms
100 dB (or better)
105 dB (ref: 0 dB output)
better than 100 dB
✓ Analog filter:
✓ Low-level linearity:
Bessel-tuned, linear phase to 40 kHz
deviation less than 1 dB to -90 dB FS
(1 kHz, 20 bit data, 80 kHz measurement bandwidth)
0.0 (off) to 91.0 dB
✓ Volume range:
✓ Volume resolution:
0.5 dB steps above 31.0 in display
1.0 dB steps between 11–31.0 in display
2 dB steps below 11.0 in display
4 S/PDIF electrical on RCA
✓ Digital inputs:
1 S/PDIF electrical on BNC
1 AES/EBU electrical
1 EIAJ optical
✓ Analog inputs:
1 balanced stereo pair on XLR
7 single-ended pairs on RCA
✓ RF Demodulator input:
✓ Digital input impedance:
Digital Input 3 (w/opt. RF demodulator card)
75Ω (S/PDIF electrical)
110Ω (AES/EBU electrical)
96
✓ Digital output:
1 RCA (S/PDIF electrical)
✓ Digital output impedance:
✓ Main analog outputs:
75Ω (S/PDIF electrical)
3 balanced outputs (main left, center, right)
8 single-ended outputs (5.1 plus 2 auxiliary channels)
✓ Analog output impedance:
10Ω
80 mA per outlet
less than 50 W
✓ Available trigger current:
✓ Power consumption:
✓ Mains voltage:
100V, 120V, 200V, 230V, 240V,
factory set for destination country only
50 or 60 Hz,
✓ Mains frequency:
factory set for destination country only
See “Dimensions”
✓ Overall dimensions:
✓ Shipping weight:
34 lbs. (15.5 kg)
For more information, see your Proceed dealer, or contact:
Madrigal, Inc., P.O. Box 781,
2081 South Main Street, Middletown, Connecticut 06457 USA
Telephone (860) 346-0896
FAX (860) 346-1540
If purchased in the United States or Canada, the warranty on this Proceed
product is owner-transferable. If your product requires service, you must obtain
a Return Authorization before shipping it to Madrigal. Madrigal reserves the
right to repack any product which arrives improperly packed for shipment and
to charge the owner for the required packing material. For warranty
information and conditions on products purchased in other countries, contact
your local dealer or distributor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
17.26"
43.84 cm
E
S
X
U
T
E
R
N
D
U
E
N
D
D
T
P
R
O
L
O
G
I
C
I
I
b
a
l
a
n
c
e
R
O
THX SURROUND EX
m
a
s
t
e
r
c
e
n
t
e
r
r
v
c
r
1
d
i
s
c
1
v
c
r
2
/
d
p
i
s
c
2
t
v
/
a
u
u
x
x
s
a
t
t
e
l
l
i
t
e
audio video
preamplifier
e
a
r
c
d
t
a
e
a
u
n
e
r
m
o
r
e
s
u
r
r
o
u
n
d
m
o
d
e
4.55"
11.6 cm
L A S E R
2 9 . 0
s
u
b
r
e
c
a
l
l
d
e
l
a
y
i
n
p
u
t
l
eve
l
m
u
t
e
s
t
a
n
d
b
y
p
a t h
m
a
i
n
r
e
m
o
t
e
b
o
t
h
d
n
i
s
p
n
l
a
y
i
t
e
s
i
t
y
p
o
we
r
PR
O
C
E
E
D
.420"
1.07 cm
15.56"
39.52 cm
1.03"
2.62 cm
1.03"
2.62 cm
14.46"
36.73 cm
13.28"
33.73 cm
97
1.175"
2.98 cm
17.61"
44.73 cm
14.46"
36.73 cm
4.55"
11.6 cm
17.26"
43.84 cm
0.5"
1.27 cm
13.28"
33.73 cm
1.175"
2.98 cm
10.26"
26.06 cm
2.20"
5.59 cm
2.00"
5.08 cm
(note that additional space must be allowed
for connections behind the unit)
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack Mount Kit
If you need or prefer to rack mount your AVP2, contact your Proceed dealer
about the optional rack mount kit. This purpose-designed assembly replaces the
standard top cover of the unit with one designed to support this relatively heavy
component solely from the “ears” that bolt into the rack.
To use the rack mount kit, simply replace the standard top cover with the rack
mount top cover. (Full instructions are included with the top cover when pur-
chased separately.) Once the rack mount top cover is in place, you may bolt the
entire unit securely to any EIA-standard rack.
98
The mounted amplifier and rack mount kit occupies four standard rack units of
height.
Download from Www.Somanuals.com. All Manuals Search And Download.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Madrigal, Inc.
2081 South Main Street, P.O. Box 781
Middletown, Connecticut 06457 USA
Telephone: (860) 346-0896
Fax: (860) 346-1540
http://www.madrigal.com
is a registered trademark of Madrigal, Inc.
a Harman International company
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
The THX logo, THX, Home THX, Home THX Cinema,
Re-Equalization, Decorrelation, and Timbre Matching
are registered trademarks of Lucasfilm Ltd.
“DTS” is a registered trademark of Digital Theater Systems, Inc.
630666
© 3/2002 Madrigal, Inc. All rights reserved.
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|