WS-9014U
Wireless 433 MHz
Temperature Station
Instruction Manual
1
nload from Www.Somanuals.com. All Manuals Search And Downl
INVENTORY OF CONTENTS
1. The indoor temperature station (Figure
1)
2. The remote temperature sensor (TX6U)
and mounting bracket. (Figure 2)
3. 3 each, 1/2” Philips screws.
4. One strip of double sided adhesive tape.
5. Instruction Manual and Warranty Card.
Figure 1
Figure 2
ADDITIONAL EQUIPMENT
(not included)
1. 1 Philips screwdriver.
2. 2 Fresh AA 1.5V batteries.
3. 2 Fresh AA 1.5V batteries.
3
nload from Www.Somanuals.com. All Manuals Search And Downl
QUICK SETUP
Hint: Use good quality Alkaline
Batteries and avoid rechargeable
batteries.
1. Have the indoor
temperature station and
remote temperature sensor
3 to 5 feet apart.
2. Batteries should be out of
both units for 10 minutes.
3. Place the batteries into the
remote temperature
sensor first then into the
indoor temperature station.
(All remote temperature sensors must be
started before the indoor temperature
station)
4. DO NOT PRESS ANY
BUTTONS FOR 10
MINUTES.
4
nload from Www.Somanuals.com. All Manuals Search And Downl
In this time the indoor temperature
station and remote temperature sensor
will start to talk to each other and the
display will show both the indoor
temperature and an outdoor temperature.
If the indoor temperature station does
not display both temperatures after the
10 minutes please retry the set up as
stated above. After both indoor and
outdoor temperatures are displayed for
10 minutes you can place your remote
temperature sensor outdoors and set
your time.
The remote temperature sensor should
be placed in a dry, shaded area. The
remote temperature sensor has a range
of 80 feet. Any walls that the signal
will have to pass through will reduce
distance. An outdoor wall or window
will have 20 to 30 feet of resistance and
an interior wall will have 10 to 20 feet
5
nload from Www.Somanuals.com. All Manuals Search And Downl
of resistance. Your distance plus
resistance should not exceed 80 ft. in a
straight line.
NOTE: Fog and mist will not harm
your remote temperature sensor but
direct rain must be avoided.
To complete the set up of your indoor
temperature station after the 10 minutes
have passed please follow the steps
below.
1. Press and hold the “SET” button
for 5 seconds.
Note: A “12h” or “24h” will appear
on the top line. (“12h” for AM/PM,
“24h” for military time)
a. To change between “12h”
and “24h” press and
release the “MIN/MAX”
button.
6
nload from Www.Somanuals.com. All Manuals Search And Downl
b. When you have your
choice shown on the
display press and release
the “SET” button once.
2. Degree Fahrenheit will now show.
a. To change between
Fahrenheit and Celsius,
press and release the
“MIN/MAX” button.
b. When you have your
choice shown on the
display press and release
the “SET” button once.
3. An hour will now be flashing.
a. Press and release the
“MIN/MAX” button until
the correct hour is shown.
Note: When in the 12h mode
there is “PM” displayed under
the word TIME when in the
7
nload from Www.Somanuals.com. All Manuals Search And Downl
PM hours. During the AM
hours this area will be blank.
b. When the correct hour is
shown, press and release
the “SET” button once.
4. A minute will now be flashing.
a. Press and release the
“MIN/MAX” button until
the correct minutes are
displayed.
Press and release the SET button
once more and you are done.
DETAILED SETUP GUIDE
I. BATTERY INSTALLATION
A. REMOTE TEMPERATURE
SENSOR
8
nload from Www.Somanuals.com. All Manuals Search And Downl
1. Remove the mounting bracket.
2. Remove battery cover
3. Observing the correct polarity, install
2 AA batteries—make sure they do not
spring free, or start-up problems may
occur. Replace cover.
B. INDOOR TEMPERATURE
STATION
Note: After the batteries are installed, DO
NOT press any buttons. This may interfere
with the signals, causing temperatures to
register incorrectly.
9
nload from Www.Somanuals.com. All Manuals Search And Downl
1. Remove the battery cover on the
backside. To do
this, push up and
pull out.
2. Observing the
correct polarity,
install 2 AA
batteries.
3. Replace battery
cover.
4. Wait 10 minutes
or until both the indoor and outdoor
temperatures are shown on the indoor
temperature station.
5. The indoor
temperature station
should now show: “-:- -
” in the TIME LCD,
and temperatures in the
INDOOR and
OUTDOOR LCD’s.
10
nload from Www.Somanuals.com. All Manuals Search And Downl
II. TIME
A. SETTING THE TIME
1. Press and hold
the “SET”
button for 5
second, “12h”
will appear in
the TIME LCD.
2. Press and
release the
“MIN/MAX” button to select either
12h time (am/pm) or 24h time
3. Press and release the “SET” button 2
times, the hour will flash in the upper
left corner.
4. Press and release the “MIN/MAX”
button to set the hours
5. Press and release the “SET” button to
move to the minute setting
6. Press and release the “MIN/MAX”
button to set the minutes.
7. Press and release the “SET” button to
activate the clock.
11
nload from Www.Somanuals.com. All Manuals Search And Downl
Note: When in 12h mode, there is only a
“PM” display, which appears under “TIME.”
If there is no display here it is AM. Make
sure you set the time accordingly.
III. UNITS OF TEMPERATURE
MEASURE
A. SELECTING UNITS OF
MEASUREMENT
1. Press and hold the “SET” button for 5
second until “12h” or “24h” appears in
the TIME LCD.
2. Press and release the “SET” button
again, “°F” will appear in the TIME
LCD.
3. Press and release the “MIN/MAX”
button to shift between °F and °C.
4. Press and release the “SET” button
twice to activate settings.
12
nload from Www.Somanuals.com. All Manuals Search And Downl
IV. FEATURES
A. MINIMUM AND MAXIMUM
TEMPERATURES
1. Press and release the “MIN/MAX”
button, “MIN” appears in the
temperature LCD’s and the recorded
minimum temperatures are displayed.
2. Press and release the “MIN/MAX”
button to toggle to the maximum
temperatures. The time of occurrence
of the value for outdoor temperature
will also flash.
B. RESETTING THE MINIMUM AND
MAXIMUM TEMPERATURES
1. To reset both the minimum and
maximum temperatures—press and
hold the “RESET/+” button for 4
seconds.
C. ADDING ADDITIONAL
REMOTE TEMPERATURE
SENSORS (OPTIONAL)
13
nload from Www.Somanuals.com. All Manuals Search And Downl
1. The WS-9014U is able to receive
signals from 3 different remote
temperature sensors. Following are
some brief instructions for the basic
set-up of remote temperature sensor
units with the WS-9014U. These extra
sensors can be purchased through the
same dealer as this unit, or by
contacting La Crosse Technology
directly. A TX6 will monitor
temperature only, a TX3U will
monitor temperature and display the
temperature on its LCD, and the
TX3UP will monitor the temperature
via a probe for use in pools, spas, etc.
Note: When setting up multiple units it
is important to remove the batteries
from all existing units in operation,
then to insert batteries first into all the
remote temperature sensor units, and in
numeric sequence. Second, install
batteries into the indoor temperature
station. Transmission problems will
arise if this is not done correctly and if
14
nload from Www.Somanuals.com. All Manuals Search And Downl
the total time for set-up exceeds 6
minutes.
2. It is necessary to remove the batteries
from all units currently in operation.
3. Remove the battery covers to all
remote temperature sensor units.
4. Place all remote temperature sensor
units in a numeric sequential order.
5. In sequential order, install batteries
(follow the same battery installation
procedures seen in section “I” of the
Detailed Set-Up Guide).
6. Install batteries into the indoor
temperature station.
7. Follow the Detailed Set-Up Guide for
programming and operating
instructions.
D. VIEWING AND OPERATING
WITH MULTIPLE REMOTE
TEMPERATURE SENSOR UNITS
1. To view the temperature of a different
remote temperature sensor unit, press
and release the “CH” button. A shift
15
nload from Www.Somanuals.com. All Manuals Search And Downl
from one “boxed” number to the next
should be observed in the OUTDOOR
LCD.
2. To view the Minimum/Maximum
temperature: first select from which
remote temperature sensor to read data
(indicated by the “boxed” number).
Pressing and releasing the
“MIN/MAX” button will toggle
through the minimum and maximum
indoor temperature, and the minimum
and maximum outdoor temperature.
3. To reset the Minimum/Maximum
readings, press and hold the
“MIN/MAX” button for four seconds.
V. MOUNTING
Note: To achieve a true temperature
reading, avoid mounting in direct sunlight.
We recommend that you mount the remote
temperature sensor on an outside North-
facing wall. The sending range is 80ft;
obstacles such as walls, concrete, and large
metal objects will reduce the range. Place
16
nload from Www.Somanuals.com. All Manuals Search And Downl
both units in their desired location before
permanently mounting.
A. REMOTE TEMPERATURE
SENSOR
1. Remove the mounting bracket from
the remote temperature sensor
2. Mount using either screws or
adhesive tape.
3. Reattach the remote temperature
sensor to the mounting bracket.
B. THE TEMPERATURE STATION
1. The indoor temperature station comes
with the table stand already mounted.
If you wish to use the table-stand, all
that is required is to place the indoor
temperature station in an appropriate
location.
2. To wall mount, remove the table
stand. To do this, pull down on the
stand from the rear and rotate forward.
a) Fix a screw (not included) into the
desired wall, and place the indoor
17
nload from Www.Somanuals.com. All Manuals Search And Downl
temperature station onto the screw
using the hanging hole on the
backside. Gently pull the indoor
temperature station down to lock the
screw into place.
TROUBLESHOOTING
NOTE: For problems not solved, please
contact La Crosse Technology via e-mail or
phone, or visit our website,
Problem: The LCD is faint
Solution: Replace batteries
Problem: No outdoor temperature is
displayed.
Solution:
1) Remove all batteries, reinsert into remote
temperature sensor first, and then into the
indoor temperature station.
2) Place remote temperature sensor closer to
the indoor temperature station.
3) Be sure all batteries are fresh.
18
nload from Www.Somanuals.com. All Manuals Search And Downl
4) Place remote temperature sensor and
indoor temperature station in position so
the straight-line signal is not passing
through more than two or three walls.
Problem: Temperatures do not match if
units are placed next to each other.
Solution: Each temperature sensor is
manufactured to be accurate to within 1
degree plus or minus and under normal
conditions; so two temperature sensors could
be as much as 2 degrees different. However,
the difference can be exaggerated further
because the temperature sensors are
designed for different working
environments. The indoor sensor is less
responsive to ambient air currents because of
the shielding effect of the display's case. In
addition, the case can act as a heat sink to
absorb and store heat from external sources
(i.e. handling of the case or radiant heat). In
addition, the much greater range of the
outdoor temperature sensor requires a
different calibration curve than the indoor
range. Error is usually greater at the extreme
19
nload from Www.Somanuals.com. All Manuals Search And Downl
ends of a range, making it harder to compare
different ranges with different curves. Under
non-laboratory conditions, it is difficult to
compensate for the above factors and obtain
an accurate comparison.
MAINTENANCE AND CARE
INSTRUCTIONS
•
•
Extreme temperatures, vibration, and
shock should be avoided to prevent
damage to the units.
Clean displays and units with a soft,
damp cloth. Do not use solvents or
scouring agents; they may mark the
displays and casings.
•
•
Do not submerge in water.
Do not subject the units to unnecessary
heat or cold by placing them in the
oven or freezer.
•
Opening the casings invalidates the
warranty. Do not try to repair the unit.
Contact La Crosse Technology for
repairs.
20
nload from Www.Somanuals.com. All Manuals Search And Downl
SPECIFICATIONS
Transmitting
433MHz
Frequency
Measuring Temperatures
Indoor
Temperature
Station: Indoor
32°F to 156.2°F with
0.2°F resolution.
(0°C to 69.0°C with
0.1°C resolution)
Indoor
Temperature
Station: Outdoor
-21.8 °F to 156.2°F with
0.2°F resolution.
(-29.9°C to 69.0°C with
0.1°C resolution)
Temp accuracy
Transmitting
range
+/- 1°F (+/- .5°C)
Maximum 80 feet (25m)
open space
Temperature check
Indoor
Outdoor
Every 10 seconds
Three times in 10
minutes
Batteries—(Alkaline recommended)
Remote
2 x AA, 1.5V
Temperature
Sensor
21
nload from Www.Somanuals.com. All Manuals Search And Downl
Indoor
2 x AAA, 1.5V
Temperature
Station
Dimensions: (L x W x H)
Indoor
Temperature
Station
2.36 x 0.88 x 5.90 in.
Remote
Temperature
Sensor
1.57 x 0.85 x 5.00 in.
Approximately 1 year
Battery life
WARRANTY INFORMATION
La Crosse Technology provides a 1-year warranty
on this weather station. Contact La Crosse
Technology immediately upon discovery of any
defects covered by this warranty.
Before sending the weather station in for repairs,
contact La Crosse Technology. The weather
station will be repaired or replaced with the same
or similar model.
22
nload from Www.Somanuals.com. All Manuals Search And Downl
This warranty does not cover any defects resulting
from improper use, unauthorized repairs, faulty
batteries, or the weather stations inability to
receive a signal due to any source of interference.
LA CROSSE TECHNOLOGY WILL NOT
ASSUME LIABILITY FOR INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, OR OTHER
SIMILAR DAMAGES ASSOCIATED WITH
THE OPERATION OR MALFUNCTION OF
THIS WEATHER STATION. THIS PRODUCT
IS NOT TO BE USED FOR MEDICAL
PURPOSES OR FOR PUBLIC INFORMATION.
THIS PRODUCT IS NOT A TOY. KEEP OUT
OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You
may also have other rights specific to your State.
Some States do no allow the exclusion of
consequential or incidental damages therefore the
above exclusion of limitation may not apply to
you.
For warranty work, technical support, or
information contact:
La Crosse Technology
2809 Losey Blvd. S.
La Crosse, WI 54601
23
nload from Www.Somanuals.com. All Manuals Search And Downl
Phone: 608.782.1610
Fax: 608.796.1020
e-mail:
(warranty work)
(information on other products)
web:
FCC DISCLAIMER
This device complies with part 15 of
the FCC rules. Operation is subject to the
following two conditions: (1) this device may not
cause harmful interference, and (2) this device
must accept any interference received, including
interference that may cause undesired operation.
Freq. 433.92 MHz
La Crosse Technology
Made in China
WS-9014U
24
nload from Www.Somanuals.com. All Manuals Search And Downl
FCC ID: OMO-01RX (Receiver),
OMO-01TX (transmitter)
THIS DEVICE COMPLIES WITH PART 15
OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO
CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT
INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
25
nload from Www.Somanuals.com. All Manuals Search And Downl
|