FAST TRACK PRO
4 x 4 Mobile USB Audio/MIDI Interface with Preamps
User Guide
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 What’s in the Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 Fast Track Pro Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
4 Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operating Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
5 Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
6 Hardware Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7 The Software Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Bandwidth Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sample Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Maximum Sample Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Latency Tab (Windows XP only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
About Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8 Using the Fast Track Pro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting Up Your Recording Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the Mic/Inst Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the Coaxial S/PDIF Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting the Sample Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Monitoring Your Inputs for Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using the Input/Playback Mix Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Selecting Your Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Headphone Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Stand-alone Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9 Warranty Terms & Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Warranty Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Warranty Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
11 Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
12 Product Specs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Fast Track Pro User Guide
English
1
› Introduction
Thank you for choosing the M-Audio Fast Track Pro. The Fast Track Pro has been designed to give you a professional, portable audio and
MIDI interface for your Windows or Macintosh laptop or desktop computer. Using the convenience and dependability of the industry-
standard USB bus, the Fast Track Pro provides your computer with an exceptionally flexible audio interface offering unequalled routing
power and versatility, while delivering high-resolution 24-bit audio to and from your computer at sampling rates up to 96kHz. The Fast
Track Pro also gives you sixteen channels of MIDI in and out—all in a sleek, rugged, lightweight and highly portable design. It connects
to your computer with a single USB cable—no tools needed, no cards to install, and no bulky external power supply.
The Fast Track Pro was created with the home or portable studio user in mind. With two high-quality microphone/instrument preamps,
the Fast Track Pro gives you a great sounding, easy-to-use interface for your digital audio software. The convenient front panel hybrid
XLR/TRS inputs can accommodate balanced or unbalanced line or instrument levels, with switchable phantom power and individual
–20dB pads. The rear panel offers you insert points for inputs one and two, two balanced TRS analog outputs and four unbalanced RCA
connectors, as well as dedicated S/PDIF inputs and outputs, for a total of four inputs and four outputs.
The front panel is also set up for easy monitoring, with a variable Input/Playback knob and mono switch, dedicated headphone level
control and A/B switch for headphone signal source selection. Signal and clipping indicators, MIDI input and output LEDs, and phantom
power indicators make the Fast Track Pro an ideal solution for beginning and advanced computer recording users.
Even if you’re an experienced musician and digital recording enthusiast, please take some time to read through this owner’s manual and
familiarize yourself with the Fast Track Pro’s features and operation. You may also want to refer to your audio software’s documentation
to better understand how the Fast Track Pro’s features may be integrated with the program. Your experience and enjoyment of your Fast
Track Pro will be greatly enhanced by a good working knowledge of your audio software.
2
3
› What’s in the Box
Your Fast Track Pro package contains the following:
< Fast Track Pro mobile recording interface
< CD-ROM containing driver software and User Manual in PDF format
< Printed Quick Start Guide
< CD-ROM containing Ableton Live LiteTM 4.0 software, GT Player Express, ProSessions drum loops and MP3 drum songs
< Six-foot USB cable
› Fast Track Pro Features
< Two front-panel balanced/unbalanced mic/instrument/line inputs on combo XLR/TRS jacks, with individual instrument/line level
switches and –20dB pad switches
< Two balanced/unbalanced outputs on TRS jacks
< Two inserts on TRS jacks
< Four unbalanced outputs on RCA jacks
< S/PDIF digital I/O on coaxial jacks
< Signal and Clip indicators for inputs 1 & 2
< Two mic pre input level controls
< Supports sample rates up to 96kHz with full 24-bit resolution
< Functions as a stand-alone 24-bit/44.1kHz A/D converter
< MIDI Input and Output with front-panel MIDI I/O indicators
< Power LED
< Phantom Power switch with indicator LED
< Mono switch for input monitoring
< Variable Input/Playback control for input monitoring
< Output Level control
< A/B switch for headphone source selection
< Headphone Level knob
< Front-panel headphone output
< Output Level control
< Rear-panel Kensington lock port
< Driver support for WDM/MME (Windows XP), CoreAudio (MacOS X (v10.3.9 or later), and ASIO2.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
4
› Minimum System Requirements
Operating Systems
Windows
The Fast Track Pro is supported under Windows XP, with Service Pack 2 or later only. It is not supported under Windows 2000, Windows
98, 98SE or Windows ME. Visit the Windows update web pages to make certain you have the most current updates and fixes supplied
by Microsoft.
Mac
The Fast Track Pro is supported under Mac OS X version 10.3.9, 10.4.2 or later. Earlier versions of Mac operating systems are not
supported.
Hardware
Windows
< Pentium 3 – 500 MHz (higher speed CPU may be necessary for laptops)
< 256MB RAM
< DirectX 9.0c or higher
< Windows XP (SP2)
(Windows 2000, 98, 98SE, ME & NT not supported)
Mac
< Macintosh G3** 600 / G4** 667MHz (higher speed may be necessary for laptops)
< 256MB RAM
< OS X 10.3.9 or later (earlier versions of Mac operating systems are not supported)
*M-Audio suggests that you also check the minimum system requirements for your software, as they may greater than the
above.
** G3/G4 accelerator cards not supported; native FireWire ports required.
5
› Controls and Connectors
Front Panel
1. Signal Indicator LEDs (Signal) – The Signal LED will illuminate green when an input signal of –24dBFS is detected.
2. Clip Indicator LEDs (Clip) – The Clip LED will illuminate red when the input signal reaches 1dBFS below the clipping point. If the red
Clip LED lights often or stays lit for any period of time, lower the input gain level on that channel.
3. Input Gain Level Knob (GAIN) – Controls the input level of the associated Mic/Inst input (6). The variable gain range is >40dB.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Fast Track Pro User Guide
4. Instrument/Line Selector Button (Inst/Line) – This button selects the input level of the front panel 1⁄4” inputs. In the out position,
the inputs are set to accept an instrument level signal (such as that from a guitar or bass) while in the in position they are set to
accept a line level input (such as that from a keyboard or drum machine). Please note that the XLR input level is unaffected by
this switch.
5. Pad Button (Pad) – With this switch in the in position, a –20dB pad is inserted into the input circuit, lowering the input level. Use
this pad when the input level of your analog signal is too hot (as indicated by illumination of the Clip LED (2)), even with the GAIN
knob (3) at or near minimum.
6. Microphone/Instrument Inputs (Mic/Inst) – These Neutrik hybrid connectors will each accept a low-impedance mic level signal
on a standard three-pin balanced XLR or TRS plug, or a high-impedance instrument level signal on an unbalanced 1/4” TS
plug.
7. Stereo/Mono Button (Stereo/Mono) – This button toggles the direct input monitoring between stereo and mono operation. In
Mono mode, an input will be heard equally in the left and right of the headphones. In Stereo mode, input 1 will be heard in the
left while input 2 will be heard in the right.
8. MIDI Input/Output Indicator LEDs (MIDI In/MIDI Out) – These LEDs display MIDI input and output activity. They will light whenever
MIDI data is seen at the rear panel MIDI output (20) or MIDI input (21).
9. Input/Playback Mix Level Knob (Mix IN, PB) – This knob controls the audio mix sent to the Line Outputs, fading between the
input signals (input monitoring) and the output signal from your audio application software. When turned fully counter-clockwise
(IN position), only the input signals are heard at the line outputs. When turned fully clockwise (PB position), only the output signal
from your DAW software is heard at the line outputs.
10. Output Level Knob (Output Level) – This knob controls the signal level at the line outputs. This control is independent from the
Level knob (14).
11. A/B Monitor Selector Button (A/B) – This switch selects the output source sent to the Level knob (14). In the A (out) position, the
main line output signal is sent to the headphone outputs. In the B (in) position, the signal assigned to the S/PDIF output is sent
to the headphone outputs.
12. Phantom Power Indicator LED (48V) – This LED lights to indicate the presence of 48V phantom power at the front-panel XLR
inputs, as activated by the rear-panel Phantom Power switch (22).
13. Power Indicator LED (Power) – This LED lights when the Power switch (16) is activated, with the unit receiving power from either
the host computer’s USB bus, or from the (optional) external power supply.
14. Headphone Output Level Knob (Level) – This knob controls the output level to the Headphone output (15). It is independent of
the main Output Level control knob (10).
15. Headphone Output – This is a 1⁄4” stereo TRS jack, designed to drive a pair of stereo headphones. The output level is controlled
by the Level knob (14), and its source is selected by the A/B button (11).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
16. Power Button (Power) – Pressing this button will power on the Fast Track Pro, illuminating the front-panel Power LED (13). The
unit must be connected to a functioning host computer’s USB bus, or to the optional external power supply.
17. Kensington Lock Port – This connector is compatible with Kensington® security cables to protect your device from theft.
Security Slot Specifications
Lock Clearance Specifications and Electrical Considerations
The Notebook MicroSaver has an interference volume inside
the computer equipment it secures. There should not be any
electrical components adjacent to the slot, and the MicroSaver
product should never be in contact with any electrical
components.
Notes:
1. Interpret dimensions and tolerances per ASME Y14.5M-1994.
2. All indicated dimensions are in millimeters. Indicated
volume to be left free and clear of obstructions. Cable ring
can rotate 360 degrees with respect to hole.
Cable
Wall thickness
range including
metal backing
2.50 to 4.00
+.26
7.00
–.00
Rotating cable
ring
+.26
Metal backing
recommended
> 0.8 stainless
steel
3.00
–.00
22.60
4 * R 1.00 max
26.60
7.70
Min. clearance
Kensington Security Slot
Slot Clearance—Side view
All measurements are in millimeters
All measurements are in millimeters
R 3.50
R18.50
Cable ring can
rotate 360° with
respect to slot
R30.00
Lock at base
Slot Outside Clearance
Slot Inside Clearance
All measurements are in millimeters
All measurements are in millimeters
Kensington Technology Group
2000 Alameda de las Pulgas
San Mateo, CA 94403
© 2002 Kensington Technology Group, a division of ACCO Brands, Inc. All rights
reserved. Kensington is a registered trademark of ACCO World Corporation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Fast Track Pro User Guide
18. Power Supply Connector (9V DC 500 mA) – Connect the optional 9V DC 500mA power supply to this jack when using the Fast
Track Pro as a stand-alone 24-bit A/D converter. Use the optional power supply to power the Fast Track Pro.
19. USB Input (USB) – Connect a standard USB cable to this port, connecting the other end to your host computer.
20. MIDI Output (MIDI Out) – Connect to the MIDI input of your controller or other MIDI device.
21. MIDI Input (MIDI In) – Connect to the MIDI output of your controller or other MIDI device.
22. Phantom Power Switch (48V PH Power) – Sliding this switch activates the phantom power circuitry, sending 48V power to the
front-panel XLR inputs for use with condenser microphones requiring external power.
23. S/PDIF Output (S/PDIF Out) – Digital output on coaxial (RCA-type) connector. The S/PDIF Out is activated by selecting outputs 3
and 4 in the Control Panel (see section 7). The S/PDIF output signal is duplicated on Outputs 3 and 4 (26). This output will also
support pass-through of AC-3 or DTS encoded surround formats.
NOTE: When AC-3 or DTS encoded signals are passed through this output, all analog input and output will be muted.
24. S/PDIF Input (S/PDIF In) – Digital input on coaxial (RCA-type) connector. This input will accept digital input signal at any of the
supported sample rates.
25. Unbalanced Outputs 1 and 2 (Outputs 1/2) – These are unbalanced outputs on RCA connectors. The signal to these outputs
mirrors the signal to TRS Outputs 1 and 2 (27).
26. Unbalanced Outputs 3 and 4 (Outputs 3/4) – These are unbalanced outputs on RCA connectors. The signal to these connectors
mirrors the signal to the S/PDIF outputs (23), and is activated by selecting outputs 3 and 4 in the control panel (see section 7).
27. Balanced Outputs 1 and 2 (TRS Outputs 1/2) – These are balanced 1⁄4” TRS jacks. The output signal to these jacks is controlled
by the front-panel Output Level (10), and Input/Playback Mix Level.
28. Inserts 1 and 2 (Insert 1 / Insert 2) – These 1⁄4” TRS jacks are configured to connect to an analog outboard effect (compressor/
limiter, delay, reverb, etc.), inserting the effect between the preamp and the A/D converter. These inserts are only active
when a connector is inserted, and are otherwise bypassed. The TRS jack is configured as follows: Tip=Send; Ring=Return;
Sleeve=Ground.
6
› Hardware Connections
< Connect the Fast Track Pro’s Balanced Outputs 1 and 2 to your amplifier, powered monitors or mixer.
< Connect your outboard effects units or dynamic processors to the Fast Track Pro’s Insert 1 and Insert 2 jacks, using an insert-
configured Y-cable (balanced TRS-to-dual 1/4-inch mono).
< Connect your S/PDIF digital equipment (DAT or CD recorder, etc.) to the Fast Track Pro’s S/PDIF digital in and out connectors.
(NOTE: the S/PDIF output is only active when Outputs 3 and 4 are activated in the control panel.)
< Connect your headphones to the Fast Track Pro’s front-panel headphone output.
< Connect a microphone (using XLR or TRS/TS connector) or instrument (using TRS/TS connector only) such as an electric guitar
or bass to the front-panel Mic/Inst input channels 1 and 2. If connecting a 1⁄4” connector, make sure the Inst/Line button is set to
the correct input level.
< Connect your MIDI device’s MIDI output to the Fast Track Pro’s MIDI input.
< Connect your MIDI device’s MIDI input to the Fast Track Pro’s MIDI output.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Fast Track Pro User Guide
Open the Control Panel by clicking on the Fast Track Pro icon in the Windows Control Panel. On the Mac, click on the Fast Track Pro icon
in the System Preferences pane. In most digital audio applications, you may also access the Control Panel via the program.
In Windows, the Control Panel shows three tabs: Bandwidth, Latency and About. On the Mac, the Control Panel shows two tabs:
Bandwidth and About. Descriptions of the functions within each tab are detailed in this section.
Channels
In this field, you can activate and deactivate input and output channels. Based on the number and configuration of channels selected,
the Maximum Sample Rate will change to reflect the maximum sample rate available at the selected setting.
Sample Depth
In this field you can choose between 16-bit or 24-bit operation. Based on the setting you choose, the Maximum Sample Rate field will
change to reflect the maximum sample rate available at the selected setting.
Maximum Sample Rate
This field will change to reflect the maximum sample rate available, based on the sample depth selected in the Sample Depth section,
and the number of inputs and outputs selected in the Channels section.
Note that the Maximum Sample Rate field is a display-only field.
Configurations
At 16-bit operation, the Fast Track Pro operates as a four-in, four-out device at a maximum sample rate of 48kHz, with analog and digital
inputs available:
< Analog Input 1 & 2 and S/PDIF input
< Analog Output 1 & 2 (available on both TRS and unbalanced Outputs 1 and 2)
< S/PDIF Output (mirrored at unbalanced Outputs 3 and 4)
At 24-bit operation, the Fast Track Pro operates as a two-in, four-out device or a four-in, two-out device at a maximum sample rate of
48kHz, with analog OR digital inputs available:
< Analog In 1 and 2 or S/PDIF
< Analog Out 1 & 2 (available on both TRS and unbalanced Outputs 1 and 2)
< S/PDIF Out (mirrored at unbalanced Outputs 3 and 4)
Or
< Analog in 1 and 2
< S/PDIF In 1and 2
< Outputs 1 and 2 or 3 and 4
At 24-bit operation, the Fast Track Pro can also operate as a two-in or two-out device at sample rates of 88.2 and 96kHz. Analog or
S/PDIF can be selected for input or output.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Latency Tab (Windows XP only)
Fig 7.03 – Windows Control Panel – Latency Tab
Latency
In this field, you can regulate the latency you wish to work with. (Latency is defined as the time it takes for your input signal to pass
through your audio software and appear at the outputs).
The slider settings 80 through 2048 represent varying degrees of latency, with 2048 being the longest and 80 the shortest. A shorter
latency time is achieved by utilizing a smaller buffer size, while increasing the buffer size creates a longer latency time. Shorter latency is
always more desirable, but working with smaller buffer sizes may make some slower systems unstable.
The default setting is 256. This setting may adequately serve your purposes, but you can experiment with lower settings if you wish. If
you experience stuttering or crackling in your audio playback, try using a larger buffer size by selecting a higher latency setting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Fast Track Pro User Guide
About Page
Fig 7.04 – Windows Control Panel – About Tab
Fig 7.05 – Mac Control Panel – About Tab
This field contains information on your hardware, current firmware and driver software versions. This information may be helpful if you
ever have to update the driver software or need to call for technical support.
Clicking the links will connect you directly to our website if you are currently online.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
8
› Using the Fast Track Pro
The following sections address a number of real-life situations that you may encounter while using your Fast Track Pro. These brief
tutorials should help guide you through them.
Also check the M-Audio website from time to time for additional tutorials or FAQs.
Setting Up Your Recording Levels
Using the Mic/Inst Inputs
Connect your microphone, instrument or line level source to the Fast Track Pro’s front panel Mic/Inst inputs. Make sure the associated
channel’s Inst/Line button is set to the out (Inst) position for microphone or instrument input, or to the in (Line) position for line level
sources. If you are using a condenser microphone, be certain to slide the 48V PH Power switch to the On position (after connecting the
microphone to the XLR input). If your microphone input signal is too hot (Clip LED lights steadily), press the Pad button to lower the input
level.
Adjust each channel’s input GAIN knob to achieve a fairly steady green Signal LED without triggering the red Clip LED, while audibly
testing your input levels (i.e., strumming the guitar, or speaking into the mic).
NOTE: When recording with microphones, it is best to keep the mic at some distance from the main speakers, or use headphones
to monitor. Feedback may occur when microphones are too close to speakers.
Using the Coaxial S/PDIF Inputs
Connect the S/PDIF output of your external audio device to the Fast Track Pro’s rear panel S/PDIF In. The signal level that you receive at
the S/PDIF In will be the signal level that you record. Any adjustments to that signal level must be made at the source. If you have an
output level control on the device that you’ve connected to the Fast Track Pro’s S/PDIF inputs, adjust that output level control to change the
recording level. Most recording software will allow you to add gain to a recorded track that was made at a level that is initially too low,
but be careful that the recording level is not reaching digital clipping (signal over 0dB—going into the red) while recording.
You will then want to route the input signal to your audio software’s inputs. Refer to the section below on “Monitoring Your Inputs For
Recording,” and your software’s documentation for more information.
Setting the Sample Rate
You will want to set the sample rate from within your audio software. When the input source is an S/PDIF signal, the Fast Track Pro will
receive the sample rate from your audio application.
Monitoring Your Inputs for Recording
Using the Input/Playback Mix Control
The input/playback Mix knob controls the source of the audio sent to TRS Outputs 1 and 2, fading between the input signal (at the front-
panel Mic/Inst inputs 1 and 2) and the output signal from your audio application.
< When the knob is turned fully counter-clockwise (the IN position), only the input signals are heard at the outputs.
< When the knob is turned fully clockwise (the PB position), only the output signal from your DAW is heard at the outputs.
< Any point between the IN and PB positions will give you a mix of both inputs.
The real advantage of the Mix knob is that it enables you to monitor your live inputs in real time as you’re recording them, while also
monitoring the existing tracks coming from your DAW, as well as allowing you to control the relative levels of both sources. When you
do this, be sure to mute the inputs on the tracks you’re recording. Otherwise, you’ll hear the direct signal AND the return signal from
the DAW.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Fast Track Pro User Guide
Selecting Your Outputs
The Fast Track Pro’s outputs are selected in the Control Panel’s Bandwidth page (see Section 7).
Signals routed to Outputs 1 and 2 in your DAW application will appear at the rear-panel TRS Outputs 1 and 2, and be duplicated at
unbalanced Outputs 1 and 2.
When Outputs 3 and 4 are activated, they will show up as output channels in your DAW application. Signals routed to Outputs 3 and 4
in your DAW application will appear at the S/PDIF outputs, and be duplicated at unbalanced Outputs 3 and 4.
The level to the analog outputs is controlled by the main output level control.
Headphone Monitoring
The A/B button selects the output source sent to the front-panel headphone output. In the A (out) position, the main line output signal
(Outputs 1 and 2) is sent to the headphone outputs. In the B (in) position, the S/PDIF output signal (Outputs 3 and 4) is sent to the
headphone outputs.
The headphone output level is controlled by the Level control knob. This output level is independent of the main output level.
Stand-alone Mode
The Fast Track Pro can act as a stand-alone mic preamp with 24-bit/44.1kHz A/D converters. Inputs 1 and 2 are sent to the S/PDIF Out
and analog Outputs 3 and 4 post inserts.
9
› Warranty Terms & Registration
Warranty Terms
M-Audio warrants products to be free from defects in materials and workmanship, under normal use and provided that the product is
owned by the original, registered user. Visit www.m-audio.com/warranty for terms and limitations applying to your specific product.
Warranty Registration
Thank you for registering your new M-Audio product. Doing so immediately both entitles you to full warranty coverage and helps M-
product updates.
FastTrack Pro
Tested to comply with
FCC standards
FOR HOME OR STUDIO USE
11
Download from Www.Somanuals.com. All Manuals Search And Download.
10 › Troubleshooting
The Fast Track Pro has been designed to give you high performance and professional- quality audio. It has been tested under a wide
range of systems and operating conditions. However, there are a virtually limitless number of operating scenarios, any of which could
affect your system’s performance. Though this section cannot cover all possible issues you may encounter, we would like to offer you
some suggestions for dealing with common problems.
We recommend that you avoid connecting too many devices. The USB bus is a dependable protocol that is ideally suited for digital audio.
Nevertheless, it is important to remember that audio and multimedia streaming place considerable demands on your processor and the
USB bus. Although it is theoretically possible to chain many multiple USB devices in series, doing so has the potential to degrade your
audio performance.
Generally, USB devices do not suffer from the IRQ conflicts often encountered with PCI cards on Windows PCs. If you are having trouble
getting audio in or out of your Fast Track Pro, please check the following:
If you have no sound:
>
Check to see if the Fast Track Pro drivers are properly installed.
< In Windows XP, go to the Control Panel and double-click the System icon (under Performance and Maintenance if you
are in Category view).
< Select the Hardware tab and click the Device Manager button.
< Click the plus sign (“+”) next to Sound, Video and Game Controllers, and locate the Fast Track Pro listing. If you see a
question mark or exclamation point next to it, or if you don’t see it listed, you may need to reinstall the driver software.
>
>
Make sure your audio software has been set up to use the Fast Track Pro.
Open your application’s audio settings page and check to see if the Fast Track Pro’s ASIO, WDM, or Core Audio drivers have been
selected.
>
If you’re certain the Fast Track Pro is correctly installed and configured for your audio software, check your signal path. Make sure
your inputs are routed correctly by verifying that your application is receiving audio signal. Make sure your outputs are routed
correctly so that your signal is sent to your headphones, amp and/or monitors.
>
>
>
Check your audio connections and cables to make sure everything is plugged in correctly.
Check if the power button is enabled.
Check mic/line selector switch to verify that you’ve chosen the proper input.
If you’re trying to record a digital input to the Fast Track Pro and have no sound:
> Make sure your audio software is configured to receive digital input, and that the input source is set as clock master.
If you’re experiencing clicks and pops in your recordings:
>
>
>
>
Make sure your input levels are not too hot, as this can cause distortion and clipping.
Check the input level meters in your audio application.
If you are recording a digital input source, make sure the sync source in your audio software is set to external.
You might want to try using a larger buffer size (higher latency setting). Larger buffer sizes can increase input latency time, but
this is not an issue if you’re mixing, for example. Increasing the buffer size can be helpful, particularly in the case of older or
lower-powered systems.
>
If you are using a USB hub, try connecting the Fast Track Pro directly to your computer.
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
Fast Track Pro User Guide
11 › Contact Us
If you have any questions, comments or suggestions about this or any M-Audio product, we invite you to contact us by using the
following information:
M-Audio USA
M-Audio Germany
5795 Martin Rd., Irwindale, CA 91706
Kuhallmand 34, D-74613 Ohringen, Germany
Technical Support
Technical Support
tel (pro products):. . . . . . . . . . . . . . . . . (626) 633-9055
tel (consumer products): . . . . . . . . . . . . . . (626) 633-9066
fax (shipping):. . . . . . . . . . . . . . . . . . . . (626) 633-9032
Sales
tel . . . . . . . . . . . . . . . .+49 (0)7941 - 9870030
fax: . . . . . . . . . . . . . . . +49 (0)7941 98 70070
Sales
tel: . . . . . . . . . . . . . . . . . . . . . . . . . (626) 633-9050
fax: . . . . . . . . . . . . . . . . . . . . . . . . . (626) 633-9070
tel: . . . . . . . . . . . . . . . . . +49 (0)7941 98 7000
fax: . . . . . . . . . . . . . . . +49 (0)7941 98 70070
M-Audio U.K.
M-Audio Canda
Floor 6, Gresham House, 53 Clarenden Road, Watford
WD17 1LA, United Kingdom
1400 St-Jean Baptiste Ave. #150, Quebec City,
Quebec G2E 5B7, Canada
Technical Support
Technical Support
tel:(Mac support): . . . . . . . . . . . . . . +44 (0)1765 650072
tel: (PC support): . . . . . . . . . . . . . . . . +44 (0)1309 671301
Sales
phone (PC support): . . . . . . . . . . (418) 872-0444
phone (MAC support): . . . . . . . . . (418) 872-0444
fax. . . . . . . . . . . . . . . . . . . : (418) 872-0034
Sales
tel: . . . . . . . . . . . . . . . . . . . . . . . +44 (0)1923 204010
fax: . . . . . . . . . . . . . . . . . . . . . . +44 (0)1923 204039
phone: . . . . . . . . . . . . . . . . .(866) 872-0444
fax: . . . . . . . . . . . . . . . . . . . (514) 396-7102
M-Audio France
Floor 6, Gresham House, 53 Clarenden Road,
Watford-WD17 1LA, Royaume-Uni
M-Audio Latin America
5795 Martin Rd.
Irwindale, CA 91706 USA
Renseignements commerciaux :
0810 001 105 ou [email protected]
Assistance technique :
0820 000 731 (PC) & 0820 391 191 (MAC)
Assistance technique (e-mail) :
Fax : 01 72 72 90 52
Technical Support
phone: . . . . . . . . . . . . . . . (52 871) 747 90 25
Sales
phone: . . . . . . . . . . . . . . . . .(949) 766-7589
fax: . . . . . . . . . . . . . . . . . . .(949) 766-7590
Site web : www.m-audio.fr
M-Audio Japan
アビッドテ クノロジー株式会 社 | エムオーデ ィオ事業部
〒 460-0002 愛知県
名古屋市中区丸の内 2-18-10
2-18-10 Marunouchi
Naka-Ku, Nagoya 460-0002
Japan
カスタマーサポート(技術的なお問い合わせ)
e-mail (Macintosh 環境専
tel : . . . . . . . . . . . 052-218-0859(10:00~12:00 / 13:00~17:00)
セールスに関 するお問い合わせ
(技術的なお問 い合わせはご遠慮下さい)
tel: . . . . . . . . . . . . 052-218-3375 (9:30~12:00 / 13:00~18:00)
fax: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 052-218-0875
プレス/ メデ ィアに関 するお問い合わせ
(技術的なお問 い合わせはご遠慮下さい)
tel: . . . . . . . . . . . . 052-218-3375 (9:30~12:00 / 13:00~18:00)
fax: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 052-218-0875
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
12 › Product Specs
Digital Audio Interface Specifications
Mic Inputs (A/D)
Input Impedance
Maximum Input Level
Channel-to-Channel Crosstalk
SNR
48kHz sampling rate unless otherwise stated
2.7k Ohms unbalanced, 5.4k Ohms balanced
from +24dBu @ min gain, pad on to -40dBu @ max gain, no pad
< -110dB
-101dB, A-weighted
101dB, A-weighted
0.005% (-86dB) @ -1dBFS, 1kHz
20Hz to 20kHz, +/- 0.1dB
>40dB
Dynamic Range
THD+N
Frequency Response
Preamp Gain
Pad
-20dB pad
Instrument Inputs (A/D)
Input Impedance
Maximum Input Level
> 220k Ohms, unbalanced
from +22dBV @ min gain, pad on to -42dBV @ max gain no
pad
SNR
-100dB, A-weighted
Dynamic Range
THD+N
100dB, A-weighted
0.005% (-86dB) @ -1dBFS, 1kHz
20Hz to 20kHz, +/- 0.1dB @ 48kHz sample rate
> 40dB
Frequency Response
Preamp Gain
Pad
-20dB pad
Line Inputs (A/D)
Input Impedance
Maximum Input Level
Channel-to-Channel Crosstalk
SNR
20k Ohms balanced and unbalanced
+4.1dBu balanced/+1.9dBV unbalanced
< -110dB
-101dB, A-weighted
Dynamic Range
THD+N
101dB, A-weighted
0.005% (-86dB) @ -1dBFS, 1kHz
20Hz to 20kHz, +/- 0.1dB @ 48kHz sample rate
20Hz to 40kHz, +/- 0.1dB @ 96kHz sample rate
-20dB pad
Frequency Response
Pad
Input Inserts (Analog)
Maximum Level Send
Maximum Level Return
THD+N
+6dBV, unbalanced
+6dBV, unbalanced
0.00281% (-91dB) @ -1dB from max level, 1kHz
20Hz to 40kHz, +/- 0.1dB
Frequency Response
Line Outputs (D/A)
Output Impedance
Maximum Output Level
150 Ohms unbalanced, 300 Ohms balanced
+1.8dBV, unbalanced
+10.1dBu, balanced
Channel-to-Channel Crosstalk
SNR
< -108dB
-103dB, A-weighted
Dynamic Range
THD+N
103dB, A-weighted
0.005% (-86dB) @ -1dBFS, 1kHz
20Hz to 20kHz, +/- 0.3dB @ 48kHz sample rate
20Hz to 40kHz, +/- 0.5dB @ 96kHz sample rate
Frequency Response
Headphone Output (D/A)
Maximum Output
-2.5dBV at THD < 0.05% into 32 Ohms
32 to 600 Ohms
Working Range
051214_FTPro_UG_EN01
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
|