A u d io B u d d y
D u a l M ic P re a m p | D ire c t B o x
U s e rs M a n u a l
Download from Www.Somanuals.com. All Manuals Search And Download.
In t r o d u c t io n
This product complies with European CE requirements.
Thank you for your purchase of the M-Audio AudioBuddy™, mic
preamp and direct box. M-Audio has designed and manufactured
several different audio mixers including MiniMixer, MicroMixer 18,
MultiMixer 6, MultiMixer 10 and miXim 10. All of these mixers have
two things in common: 1.) they are exceedingly quiet -- quieter than
99% of all mixers on the market and 2.) they are uniquely configured to
meet the specific needs of the MIDI and multimedia musician.
The Audio Buddy, once again, fits these two criteria. First, it is a very
quiet mic preamp. This is because the unit’s simple and efficient
design and ultra compact layout eliminates much of the noise. The
unit also has a higher than usual voltage “rail” across its internal op-
amps. This means that you get more “punch” and much more dynamic
audio output.
S econdly, the Audio Buddy (when coupled with its ultra quiet
performance) is the perfect audio “gateway” for recording the two
most significant, non-line level instruments in the studio: microphones
and electric guitars.
The Audio Buddy has two completely independent preamplifier
sections. Each of these sections has: 1.) a balanced XLR input on the
back of the unit, 2.) a high impedance 1/4” unbalanced input (TS) on
the front of the unit, 3.) signal (present) and clipping LEDs, 4.) a gain
control and 5.) a 1/4” dual purpose output on the back of the unit that
provides either an unbalanced out (when a mono plug is used) or a
balanced out (when a stereo plug is used).
Download from Www.Somanuals.com. All Manuals Search And Download.
IMP ORTANT: Whenever one of the front panel high impedance
inputs is used, the associated back panel XLR is disabled.
The Audio Buddy also has built in phantom power which can be
switched on or off for both channels. When the rear panel phantom
power switch is in, phantom power to both channels is turned on and
the front Phan(tom) power LED will light.
IMP ORTANT: Since the phantom power switch turns phantom
power on or off for both channels, there is no way to turn phantom
power on for one channel and off for the other channel. If you are
using the high impedance inputs the phantom power switch has no
effect.
F ro n t a n d R e a l P a n e ls
When reading the following description of front and rear panel harware
features, it may be helpful to refer to the adjacent diagram.
Download from Www.Somanuals.com. All Manuals Search And Download.
F ro n t
1. High Impe da nce Input 1: High impedance (100K) input for
Preamp 1. This input is optimized for guitars or high impedance
microphones where you don’t want to load down the source.
When this input is being used XLR input 1 is disabled.
IMP ORTANT: Because the high impedance input jack is
switched, the XLR input cannot be used whenever something is
plugged into the high impedance input.
2. Sig(nal) and Clip LED Preamp 1: Whenever a signal is applied to
either the high impedance ”In” or the XLR “In” of Preamp 1, these
LEDs will show signal present and clipping levels. If a signal is
applied in this manner and the clipping LED lights too much adjust
the Preamp 1 gain control accordingly.
3. Gain Control for Preamp 1: Adjusts the Output 1 volume level
for Preamp 1. If a signal is present at either the high impedance in
or the XLR in of Preamp 1 and the Clipping LED stays lit, turn
down this gain control and adjust accordingly.
4, 5, 6. Same as 1, 2 and 3 for Preamp 2. Remember, Preamp 1
and Preamp 2 are completely independent.
7. P ha nto m Po we r Indica to r LED: When the phantom power
switch on the back of the unit is in, this LED will light indicating that
phantom power has been turned on for both XLR in 1 and XLR 2.
IMP ORTANT: Phantom power is turned on for both preamps,
i.e. there is no independent phantom power control for each of
the channels.
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Main Power Indicator LED: When power is properly applied
to the Audio Buddy and when the front power switch is in, the
main power LED will light indicating that the unit is turned on.
9. Power Switch: When power is properly applied to the Audio
Buddy and this switch is pressed in, the Audio Buddy is turned
on. When this is done the Main Power LED will light.
R e a r
10. 9-VAC Power Jack. The rear panel power jack of the Audio
Buddy accepts a 9-Volt AC, 500 milliamp power adapter.
IMPORTANT: Audio Buddy will not function unless it receives
power at this jack and the front panel power switch is
pushed in.
11, 12. Outputs 2 and 1: These are the main outputs for the dual
Audio Buddy preamps. They provide unbalanced outputs if a
tip-sleeve 1/4” plug is used. Or, they provide balanced outputs
if a tip-ring-sleeve (stereo) 1/4” plug is used. The level of these
outputs are independently controlled by the front panel gain
controls. Remember, Preamp 1 and Preamp 2 are completely
independent.
13. Phantom Power Switch: When in, phantom power is turned
on for b o th XLR In 1 and In 2. When in, the front panel
phantom power indicator LED will light showing that phantom
power is on.
14, 15. XLR-In 1&2: (# 15 is 1; # 14 is 2) Balanced XLR inputs for
preamps 1 and 2. When the rear phantom power switch is in,
phantom power is turned on to both jacks.
IMP ORTANT: If anything is plugged into either of the front-
panel high-impedance input jacks, the corresponding XLR
input will be disabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
F e a tu re s
The Audio Buddy features include:
• 2 independent XLR, fully balanced inputs.
• 2 alternate, independent 1/4” unbalanced, high impedance inputs.
These alternate 1/4” inputs are impedance matched for ideal
performance with typical electric guitars.
• Separate gain controls for each of the two preamplifiers.
• Individual signal and clipping LEDs for each of the preamplifiers.
• XLR phantom power can be switched on and off for both of the
mic preamps.
• Phantom power on or off LED indicator.
• Dual purpose independent 1/4” outputs which accept either
tip-ring-sleeve plugs for balanced signal or tip-sleeve plug for
unbalanced signal.
• Super-small size: 5.5" x 3.3" x 1.7".
• Very-quiet S/N specification.
• Heavy-duty all metal construction.
Sp e c if ic a t io n s
• Frequency Response: 5 Hz to 50 kHz, +0, -3 dB.
• Mic Gain: 60 dB max.
• Mic Input Impedance: 1 K ohm.
• Guitar Gain: 40 dB max.
• Guitar Input Impedance: 100 K ohms.
• Approximate weight: under 1/2 lb.
• Power supply: 9 VAC; 500 milliamps.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wa rra n ty a n d R e g is tra tio n
Wa rra n ty Te rm s
M-Audio warrants products to be free from defects in materials and
workmanship, under normal use and provided that the product is owned
terms and limitations applying to your specific product.
Wa rra n ty R e g is tra tio n
Immediately registering your new M-Audio product entitles you to
full warranty coverage and helps M-Audio develop and manufacture
audio.com/register to receive FREE product updates and for the
chance to win M-Audio giveaways.
© 2008 Avid Technology, Inc. All rights reserved. Product features,
specifications, system requirements and availability are subject to
change without notice. Avid, M-Audio and Audio Buddy are either
trademarks or registered trademarks of Avid Technology, Inc. All
other trademarks contained herein are the property of their
respective owners.
WARNING: This product contains chemicals, including lead,
known to the State of California to cause cancer, and birth defects
or other reproductive harm. Wa s h ha nds a fte r ha ndling.
Download from Www.Somanuals.com. All Manuals Search And Download.
080519_AudioBuddy_UG_EN01
Download from Www.Somanuals.com. All Manuals Search And Download.
|