Lucent Technologies Telephone 362EC User Manual

362EC Line/  
Extension  
Module  
362EC  
Module  
Only for use on the Lucent Technologies PARTNER  
Endeavor Communications System  
7-foot  
Line Cords  
COMBO  
COMBO  
Installation Instructions  
Important Safety Instructions  
!
WARNING:  
The following list provides basic safety precautions that should always be followed when using your  
telephone equipment:  
1. Read and understand all instructions.  
2. Follow all warnings and instructions marked on the equipment.  
3. Unplug all telephone connections before cleaning. DO NOT use liquid cleaners or aerosol cleaners. Use a  
damp cloth for cleaning.  
4. The product should be serviced by (or taken to) a qualified repair center when service or repair work is  
required.  
5. DO NOT use the product near water, for example, a wet basement location.  
6. Never push objects of any kind into the slots or openings as they may touch dangerous voltage points or  
short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the  
equipment. Doing so may result in serious damage to the components.  
7. DO NOT use the telephone to report a gas leak in the vicinity of the leak.  
8. The telephone equipment is provided with a three-wire grounding type plug. This is a safety feature. DO NOT  
defeat the safety purpose of the grounding type plug. DO NOT staple or otherwise attach the power supply  
cord to building surfaces.  
!
CAUTION:  
DO NOT block or cover the ventilation slots and openings. They prevent the product from overheating. DO  
NOT place the equipment in a separate enclosure unless proper ventilation is provided.  
Additional Safety Instructions for Installation Personnel  
1. Install the equipment to meet all the environmental and electrical requirements listed in the PARTNER  
Endeavor Installation Guide.  
2. DO NOT install equipment during a lightning storm.  
3. DO NOT install telephone jacks in a wet location unless the jack is specifically designed for wet locations.  
4. Never touch uninsulated telephone wires or terminals, unless the telephone line has been disconnected at  
the network interface.  
5. Use caution when installing or modifying telephone lines.  
6. The control unit must be securely wall mounted.  
Comcode 108272832  
June 1998 (Issue 1)  
Copyright 1998 Lucent Technologies  
All rights reserved  
PARTNER is a registered trademark  
of Lucent Technologies  
Printed in U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTNER Endeavor Communications System Installation Instructions -  
Using a 2-Slot Carrier  
IMPORTANT: To add a 362EC module to a PARTNER Endeavor system, the PARTNER Endeavor processor  
module must already be mounted on the wall. If it is not, refer to the PARTNER Endeavor Installation Guide for  
instructions. Before starting, disconnect the power cord from the power jack in the carrier. Then follow the  
instructions below.  
362EC  
Processor  
Module  
A) Move the carrier’s On/Off switch to "Off,"  
1and unplug the power cord from the wall  
outlet. B) To remove the cover, loosen the  
screw on lower front of the cover. C) Place  
one hand on the handle on the bottom front  
of the cover, and place your other hand on  
the top of the cover. Gently pull the cover up  
and away from the carrier.  
A) Verify that the PARTNER Endeavor  
3 processor module is in the center slot of the  
carrier. In the other slots, from left to right,  
install the 362EC modules. B) Align the  
module carefully in the appropriate slot, and  
push slowly but firmly in the center of the  
module until the connectors on the module  
lock into place.  
Before installing any modules, make sure the  
clear, plastic protector has been removed  
from the connector area on the rear of each  
module. To remove the protector, grasp the  
tabs on the ends of the protector and lift.  
2
!
CAUTION:  
Caution: Do not force the module. If the  
module does not insert easily, remove it,  
clear any obstruction, and reinsert it  
362EC  
Module  
362EC  
Module  
362EC  
Module  
ECS  
Proc.  
362EC  
Module  
P
F
T
4
7
10  
13  
1
4
Line  
Jacks  
Line  
Jacks  
5
7
5
6
8
9
11  
12  
14  
15  
2
3
6
8
1
9
2
18  
19  
20  
21  
10  
11  
12  
3
13  
14  
15  
26  
27  
28  
MUSIC  
ON  
HOLD  
E
X
T
E
N
S
I
10  
11  
P
F
T
34  
22  
29  
30  
12  
13  
35  
36  
18  
26  
34  
42  
10  
O
N
S
42  
43  
23  
COMBO  
24  
31  
14  
COMBO  
37  
38  
44  
45  
COMBO  
19  
20  
27  
28  
35  
36  
43  
44  
25  
11  
12  
32  
15  
COMBO  
COMBO  
33  
16  
39  
COMBO  
46  
COMBO  
17  
40  
47  
COMBO  
COMBO  
41  
48  
COMBO  
49  
Extension  
Jacks  
21  
22  
29  
30  
37  
38  
45  
46  
13  
14  
Extension  
Jacks  
23  
31  
39  
47  
15  
C
C
C
A) Plug the power cord into a properly  
Check the green lights on the fronts of the  
A) Label the lines and extension jacks.  
4 B) Connect the line and telephone cords to 5 grounded three-prong wall outlet not 6 modules. If a single light is out, power down  
controlled by a switch. B) Power up the  
control unit by moving the On/Off switch to  
the "On" position.  
the carrier, then power up the carrier. If  
multiple lights are out, power down the  
carrier, reseat both modules, then power up  
the carrier. If the lights are still out, in the  
Continental U.S., call the hotline at  
1-800-721-7071. Outside the Continental  
U.S., contact your Lucent Technologies  
Representative or local Authorized Dealer.  
the appropriate jacks on the new module.  
C) Route each cord through the hook on the  
front of its module. D) Connect the free end  
of each phone cord to the modular wall jacks  
for system extensions. E) Connect the free  
end of each telephone cord to the modular  
connecting blocks for system extensions.  
F) Gather the line and extension cords  
hanging below the hook and twist tie or wire  
wrap them. G) Place the bundle of wires in  
the indentation on the bottom carrier.  
NOTE:  
Connect ETR and T/R combination  
devices to the last two ports on the  
PARTNER Endeavor processor or  
362EC module.  
A) To replace the carrier’s cover grasp it by  
7 its upper edges and hold it squarely over the  
carrier. B) Place the cover over the modules  
and make sure it fits firmly in place. If it does  
not fit, make sure all modules are seated  
properly. C) Tighten the screw on the lower  
front of the cover.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTNER Endeavor Communications System Installation Instructions -  
Using a 5-Slot Carrier  
IMPORTANT: To add a 362EC module to a PARTNER Endeavor system, using a 5-slot carrier, the PARTNER  
Endeavor processor module and carrier must already be mounted on the wall. If it is not, refer to the PARTNER  
Endeavor Installation Guide for instructions. Follow the instructions below to install a 362EC expansion module in  
the 5-slot carrier.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lantronix Network Router 900 422 User Manual
Learning Resources Baby Toy LPK5460 GUD User Manual
Leica Model Vehicle NCL L SP A User Manual
LG Electronics Portable DVD Player M70 User Manual
Liebert Surge Protector LM250120YARCE User Manual
Life Fitness Home Gym 8245102 User Manual
Life Fitness Treadmill 9100HR User Manual
Lindy Computer Drive 70674 User Manual
Lopi Work Light Gas Lamp User Manual
Makita Cordless Saw DPC 7000 User Manual