Life Fitness Treadmill 9100HR User Manual

Life Fitness Model 9100HR (REV 1 & REV 2) Treadmill  
How To... INSTALL THE LIFELINK UPGRADE KIT  
TOOLS REQUIRED: Standard Screwdriver, Phillips Screwdriver, Hex Key Wrench Set, Pliers, Wire Cutters,  
Anti-Static Strap  
WARNING: FAILURE TO OBSERVE SAFETY PROCEDURES WHEN SERVICING THIS UNIT  
COULD RESULT IN INJURY FROM ELECTRICAL SHOCK  
STEP 1  
Turn the power off at the ON/OFF switch and unplug the unit at the wall outlet.  
STEP 2  
Ground yourself by positioning an anti-static strap around your wrist and attaching the other end (alligator clip or adhesive  
end) to a bare metal surface on the machine frame.  
(REV 1 ONLY)  
STEP 3  
Remove the CONNECTOR COVER under the left side of the DISPLAY  
CONSOLE by removing the four screws with a Phillips screwdriver and  
unplug the 4 and 10-pin CONNECTORS to the DISPLAY CONSOLE.  
STEP 4  
Remove the DISPLAY CONSOLE by removing the four allen bolts and  
washers securing the DISPLAY CONSOLE to the HANDRAILS.  
HINT: FOR EASIER REMOVAL, LOOSEN THE THREE SCREWS  
HOLDING THE HANDLEBAR TO THE RIGHT SIDE HANDRAIL.  
Remove the eight Phillips screws securing the console pan to the faceplate.  
Remove the LIFEPULSE ASSEMBLY by removing the four screws and  
unplugging the 7-PIN CONNECTOR and the ground strap. Remove the ELECTRONIC BOARD from the faceplate by removing  
the eight screws and unplugging the RIBBON CABLE and STOP SWITCH CABLE.  
STEP 5  
NOTE THE ORIENTATION OF E-PROM BY THE U-NOTCH.  
Remove and replace the E-PROM ( U1 ) with the E-PROM supplied in the upgrade kit. Return the DISPLAY CONSOLE to its  
proper position by reversing Steps 3 and 4.  
STEP 6  
Remove the four screws securing the MOTOR COVER in place and set the  
MOTOR COVER aside.  
STEP 7  
Pull out the two RUBBER MOUNTING NUTS holding the FRONT PROTECTOR  
SHIELD in position and remove it.  
STEP 8  
Remove the FRONT COVER by  
removing the four screws  
securing it in place.  
STEP 9  
Remove the two screws  
securing the TRANSFORMER  
to the POWER BOX, lift the  
TRANSFORMER off and secure  
the bracket supplied in the  
upgrade kit with the two screws  
to the same holes. To ensure the NETWORK BOARD fits, remove the 3/16  
allen bolt that holds the POWER BOX to the FRAME and replace it with the  
allen screw supplied in the upgrade kit. Slide the NETWORK BOARD  
(connector facing the front) on top of THE POWER BOX and secure it to the  
four existing holes with the four screws supplied in the upgrade kit. Take  
the TRANSFORMER and secure to the top of the bracket with the two screws supplied in the upgrade kit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Franklin Park, IL 60131  
(800) 351-3737 or (847) 451-0036 / FAX (847) 451-4137  
MO51-00K23-A014  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Land Pride Lawn Mower 357 552M User Manual
Life Fitness Bicycle Lifecycle 9100 User Manual
Lincoln Electric Welder SVM136 A User Manual
Linksys Network Card WAP200 User Manual
Mabe Canada Cooktop JCBP240 User Manual
Mace Digital Camera CAM 5 User Manual
Makita Cordless Saw 2106 User Manual
Makita Cordless Saw BLS820 User Manual
Manhattan Computer Products Satellite TV System PLAZA HD 52 User Manual
Maytag Washer MAH7500 User Manual