LCD Projector Commercial Use
Operating Instructions
PT-L6510E
PT-L6600E
Model No.
Read these instructions completely before operating this unit.
TQBJ 0119
Download from Www.Somanuals.com. All Manuals Search And Download.
lMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moutded three pin mains plug for your safety and convenience.
A 13 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the
replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSl to BS1362.
Cheque for the ASTA mark
or the BSl mark on the body of the fuse.
lf the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is
replaced. lf you lose the fuse cover, the plug must not be used until a replacement cover is
obtained. A replacement fuse cover can be purchased from an Authorized Service Centre.
If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse
should be removed and the plug cut off and disposed of safely. There is a danger of severe
electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: –THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: –The wires in this mains lead are coloured in accordance
with the following code: –
Green-and-Yellow: Earth
Blue:
Neutral
Live
Brown:
As the colours of the wire in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in
the plug which is marked with the letter E or by the Earth symbol
GREEN-AND-YELLOW.
or coloured GREEN or
The wire which is coloured BLUE must be connected to the terminal in the plug which is
marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is
marked with the letter L or coloured RED.
FUSE
How to replace the fuse. Open the fuse compartment with
a screwdriver and replace the fuse.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
W·BAL R/G/B.................................................................31
SIGNAL MODE..............................................................31
STANDARD ...................................................................31
IMPORTANT SAFETY NOTICE ......................... 2
Precautions with regard to safety ................... 5
WARNING .......................................................................5
Caution ............................................................................6
Adjusting the position .................................... 32
HORIZONTAL POSITION .............................................32
VERTICAL POSITION ...................................................32
VIDEO SIZE ..................................................................32
DOT CLK .......................................................................32
CLK PHASE ..................................................................32
KEYSTONE ...................................................................32
V. LINEARITY ................................................................32
ASPECT ........................................................................33
STANDARD ...................................................................33
Accessories ....................................................... 7
Precautions on handling .................................. 8
Example of System up...................................... 9
Location and function of each part ............... 10
Remote control ..............................................................10
Projector <Top·Front and Side> .................................... 11
Projector <Top·Rear and Side> .....................................12
Projector <Rear control panel> .....................................12
Projector <Interface panel> ...........................................13
Adjusting the Zoom/Focus ............................. 33
ZOOM............................................................................33
FOCUS ..........................................................................33
Using the Remote control unit....................... 14
Loading batteries ...........................................................14
Effective control range...................................................14
Using laser pointer ........................................................15
Setting projector IDs for remote control.........................15
Using the remote control as a PC mouse......................16
Using the remote control in wired mode ........................17
Changing the display language ..................... 33
OPTION 1 settings........................................... 34
OSD (On-Screen Display) .............................................34
RGB FORMAT...............................................................34
LENS SHIFT..................................................................34
BACK COLOUR ............................................................34
PROJECTION SCHEME 1 ............................................34
PROJECTION SCHEME 2 ............................................34
Setting-up ........................................................ 18
Projection Schemes ......................................................18
Installation Geometry ....................................................18
Projection Distances......................................................18
Setup precautions .........................................................19
Example of connecting with AV products ......................20
Example of connecting with PCs ...................................21
Example of connecting with system switcher ................22
OPTION 2 settings........................................... 35
LAMP POWER ..............................................................35
LAMP SELECT ..............................................................35
LAMP RUNTIME ...........................................................35
SETTING FUNCTION 1 [FUNC 1] ................................35
SETTING UNIT ID .........................................................36
Registering / Deleting / Displaying User Mode ..............36
Starting to use ................................................. 23
Powering Up the Projector ............................................23
Making Initial Adjustment / Settings input port...............23
Powering Off the Projector ............................................23
Leveling the Projector....................................................24
Adjusting the Vertical Position of the Picture .................24
Advice on the installation of exhaust guides .................25
Using the SERIAL............................................ 37
Connection ....................................................................37
Pin assignments and signal names ...............................37
Communication requirements .......................................37
Basic format ..................................................................37
Control command ..........................................................38
Cable specifications ......................................................38
USB control ...................................................................38
Using the Freeze function .............................. 25
Using the Shutter function ............................. 25
Using the Digital Zoom function .................... 26
Using the remote terminal.............................. 39
Indication of lamp monitor ............................. 40
Cleaning and replacing the air filter .............. 41
On-screen menus ............................................ 27
Menu screens ................................................................27
Basic Menu Operations .................................................28
Returning to the Previous Page ....................................28
Menu Items Shown with White Characters ...................28
Menu Items Setting .......................................................28
Reset the Factory Default..............................................28
Cleaning method ...........................................................41
Replacing the lamp unit.................................. 42
Lamp replacement period..............................................42
Lamp unit replacement steps ........................................43
Using the INDEX WINDOW function .............. 29
Before asking for service ............................... 45
Specifications.................................................. 46
Appendix .......................................................... 48
Dimensions ...................................................... 49
Trademark acknowledgments........................ 49
Adjusting the picture ...................................... 30
PICTURE MODE ...........................................................30
COLOUR .......................................................................30
TINT ..............................................................................30
BRIGHT .........................................................................30
CONTRAST...................................................................30
SHARPNESS ................................................................30
TV-SYSTEM ..................................................................31
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions with regard to safety
WARNING
If a problem occurs (such as no image or no sound) or if you notice smoke or a strange
smell coming from the projector, turn off the power and disconnect the power cord from the
wall outlet.
• Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.
• Cheque that no more smoke is coming out, and then contact an Authorized Service Centre for repairs.
• Do not attempt to repair the projector yourself, as this can be dangerous.
Do not install this projector in a place which is not strong enough to take the full weight of
the projector.
• If the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could result.
• Installation work (such as ceiling suspension) should only be carried out by a qualified technician.
• If installation is not carried out correctly, there is the danger that injury or electric shocks may occur.
If foreign objects or water get inside the projector, or if the projector is dropped or the
cabinet is broken, turn off the power and disconnect the power cord from the wall outlet.
• Continued use of the projector in this condition may result in fire or electric shocks.
• Contact an Authorized Service Centre for repairs.
Do not cover the air filter, the air inlet and exhust vents.
• Doing so may cause the projector to overheat, which can cause fire or damage to the projector.
Do not overload the wall outlet.
• If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire may
result.
Do not remove the cover or modify it in any way.
• High voltages which can cause fire or electric shocks are present inside the projector.
• For any inspection, adjustment and repair work, please contact an Authorized Service Centre.
Clean the power cord plug regularly to prevent it from becoming covered in dust.
• If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in fire.
Pull the power cord out from the wall outlet and wipe it with a dry cloth.
• If not using the projector for an extended period of time, pull the power cord plug out from the wall outlet.
Do not do anything that might damage the power cord or the power cord plug.
• Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively, twist
it, pull it, place heavy objects on top of it or wrap it into a bundle.
• If the power cord is used while damaged, electric Shocks, short-circuits or fire may result.
• Ask an Authorized Service Centre to carry out any repairs to the power cord that might be necessary.
Do not handle the power cord plug with wet hands.
• Failure to observe this may result in electric shocks.
Insert the power cord plug securely into the wall outlet.
• If the plug is not inserted correctly, electric shocks or overheating could result.
• Do not use plugs which are damaged or wall outlets which are coming loose from the wall.
Do not place the projector on top of surfaces which are unstable.
• If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or
damage could result.
Do not place the projector into water or let it become wet.
• Failure to observe this may result in fire or electric shocks.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions with regard to safety
Do not place liquid containers on top of the projector.
• If water spills onto the projector or gets inside it, fire or electric shocks could result.
• If any water gets inside the projector, contact an Authorized Service Centre.
Do not insert any foreign objects into the projector.
• Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so
can result in fire or electric shocks.
After removing the battery from remote control unit, keep it away from the reach of children.
• The battery can cause death by suffocation if swallowed.
• If the battery is swallowed, seek medical advice immediately.
Do not allow the + and - terminals of the battery to come into contact with metallic objects
such as necklaces or hairpins.
• Failure to observe this may cause the battery to leak, overheat, explode or catch fire.
• Store the battery in a plastic bag and keep it away from metallic objects.
Insulate the battery using tape or similar before disposal.
• If the battery comes into contact with metallic objects or other batteries, it may catch fire or explode.
A child in not made to use remote control and do not look into the laser beam emitted from
the remote control.
• Although laser emission from the remote control is not harmful to human health, do not look directly into the laser
beam or aim it at another person.
• Laser radiation can cause injury to the human eye.
Caution
Do not set up the projector in humid or dusty places or in places where the projector may
come into contact with smoke or steam.
• Using the projector under such conditions may result in fire or electric shocks.
When disconnecting the power cord, hold the plug, not the cord.
• If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks
may result.
Always disconnect all cables before moving the projector.
• Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to
occur.
Do not place any heavy objects on top of the projector.
• Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or
injury.
Do not short-circuit, heat or disassemble the battery or place it into water or fire.
• Failure to observe this may cause the battery to overheat, leak, explode or catch fire, and burns or other injury may
result.
When inserting the battery, make sure the polarities (+ and -) are correct.
• If the battery is inserted incorrectly, it may explode or leak, and fire, injury or contamination of the battery compartment
and surrounding area may result.
Use only the Specified battery.
• If an incorrect battery is used, it may explode or leak, and fire, injury or contamination of the battery compartment
and surrounding area may result close to this port, otherwise burns or damage could result.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not look into the lens while the projector is being used.
• Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.
Do not bring your hands or other objects close to the air outlet port.
• Heated air comes out of the air outlet port. Do not bring your hands or face, or objects which cannot withstand heat.
Replacement of the lamp unit should only be carried out by a qualified technician.
• The lamp unit has high internal pressure. It can easily become damaged if struck against hard objects or dropped,
and injury or malfunctions may result.
Replacement of the lamp unit should only be carried out after it has completely cooled off,
otherwise burns may result.
Disconnect the power cord plug from the wall outlet as a safety precaution before carrying
out any cleaning.
• Electric shocks can result if this is not done.
Ask an Authorized Service Centre to clean inside the projector at least once a year.
• If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation.
• It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest
Authorized Service Centre to clean the projector when required. Please discuss with the Authorized Service Centre
regarding cleaning costs.
Do not reach for the openings beside the optical lens, during horizontal or vertical movements
of the lens there is a injury hazard.
An effort to keep our environment clean, Please bring the non repairable unit your Dealer or
a Recycling Company.
Accessories
Cheque that all of the accessories shown below have been included with your projector.
Lens cover
Remote control unit
[N2QAEA000003 x1]
Power cord for U. K.
[TXFSX02VTHZ x1]
USB cable
[TKKL5103 x1]
[3.0 m, K1HB04FD0002 x1]
Power cord for Continental
[TXFSX02VTFZ x1]
Wired cable for remote control
[15 m, K1EA03NA0001 x1]
Battery for remote control unit
[R03NPE/2ST x1]
Right-side exhaust guide
[TPAKK21 x1]
RGB signal cable (for VGA)
[3.0 m,
Conversion plug
[K2RB031D0001 x1]
Left-side exhaust guide
[TPAKK22 x1]
K1HB15FA0001 x1
]
Fixing pin
[TPAMM33 x1]
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions on handling
the screen. Moreover, when not using the projector, cover
it with the accessory lens cover.
Cautions regarding transportation
Be sure to attach the lens cover before transporting the
About the screen
projector.
If the screen you are using is dirty, damaged or discolored,
attractive projections cannot be obtained. Do not apply
any volatile substances to the screen, and do not let it
become dirty or damaged.
The projection lens is extremely susceptible to vibration
and shocks. When carrying the projector, be careful not to
subject to excessive vibration or shock while under
transport.
Lamp
Cautions regarding setting-up
A mercury lamp with high internal pressure is used as the
light source for this equipment. High-pressure mercury
lamps have the following characteristics.
Observe the following at all times when setting up the
projector.
Avoid setting up in places which are subject to
vibration or shocks.
• If the lamp deteriorates due to shock, scratching or the
passage of time during use, it may rupture with a loud
noise, or enter the unlit state and end its service life.
• Service life varies significantly due to individual lamp
differences and use conditions.
If the projector is set up in locations with strong vibration,
such as near a motor, or if it is installed inside a vehicle or
on board a ship, the projector may be subjected to vibration
or shocks which can damage the internal parts and cause
malfunctions or accidents. Accordingly, set up the projector
in a place which is free from such vibrations and shocks.
Do not set up the projector near high-voltage power
lines or near motors.
• Exceeding the replacement period will increase the
probability of rupture.
About the liquid crystal panel
The liquid crystal panel of the projector is built with very
high precision technology giving you fine picture details.
Occasionally, a few non-active pixels may appear on the
screen as a fixed point of blue, green or red.
Please note that this dose not affect the performance of
your LCD.
The projector may be subject to electromagnetic
interference if it is set up near high-voltage power lines or
motors.
If installing the projector to the ceiling, ask a qualified
technician to carry out all installation work.
If the projector is to be suspended from the ceiling, you
will need to purchase the separate installation kit (Model
No.: ET-PKL6500/S). Furthermore, all installation work
should only be carried out by a qualified technician.
This product cannot be used at altitudes of 1,400 m or
more above sea level. If it is used as is, there may be an
adverse effect on component service life and so on.
About optical parts
If the projector is subjected to a continuous use for more
than 6 hours every day, you may have to replace optical
parts, such as LCD panels or polarizers within less than
one year. When you use the projector in such a case, ask
your dealer or an Authorized Service Center for details.
Before carrying out cleaning and
maintenance, be sure to disconnect the
Notes on use
If using this projector more than 8hours/day (continuous
operation), special measures will be necessary to use
this projector. Please consult your dealer or Authorized
Service Centre about preparations.
power cord plug from the wall outlet.
Wipe the cabinet with a soft, dry cloth.
In order to get the best picture quality
If the cabinet is particularly dirty, soak the cloth in water
with a small amount of neutral detergent in it, squeeze
the cloth very well, and then wipe the cabinet. After
cleaning, wipe the cabinet dry with a dry cloth.
If using a chemically-treated cloth, read the
instructions supplied with the cloth before use.
Do not wipe the lens with a cloth that is dusty or which
produces lint.
If outside light or light from indoor lamps is shining onto
the screen, the images projected will not have good
contrast. Draw curtains or blinds over any windows and
turn off any fluorescent lights near the screen to prevent
reflection.
Depending on the environment where used, hot air from
the cooling fan vent may in rare cases cause disturbances
on the screen.
If any dust or lint gets onto the lens, such dust or lint
will be magnified and projected onto the screen. Use
a blower to clean any dust and lint from the lens
surface, or use a soft cloth to wipe off any dust or lint.
Do not touch the surfaces of the lens with your bare
hands.
If the surface of the lens becomes dirty from fingerprints
or anything else, this will be magnified and projected onto
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of System up
The projector features a wealth of interface ports and optional parts that can be used to set up the projection
system in diverse ways. The following presents some of those setup examples:
System 1
System 2
Picture brightness can be doubled by stacking
two projectors with the stacking brackets.
The optional high- or low-ceiling mount bracket
flexibly fits the projector in individual site
conditions.
IN
OUT
L
R
IN
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B
/
B
-
Y
/
P
B
S
Y
N
C
/
H
D
VD
OUT
RGB
1
IN
RGB
2
IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
>
PC
<
TBMU152
IN
OUT
L
R
IN
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B
/
B
-
Y
/
P
B
S
Y
N
C
/
H
D
VD
OUT
RGB
1
IN
RGB
2
IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
>
PC
<
TBMU152
(It is an image figure using the simple mount
bracket)
(It is an image figure using the Ceiling mount
bracket)
System 3
System 4
PCs equipped with a DVI-D port can be attached
to the projector for computer image viewing.
(Realization of high clear picture.)
A variety of video sources can be fed to the
projector through a system switcher.
Digital STB or
Control PC
DVD player
System Switcher
(Option)
Video deck
POWER
INPUT SELECT
3
VP
ON/OFF
OFF
1
2
4
5
6
ON
OFF
Signal Selector TW-SW
S
J
Laser disc player
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and function of each part
Remote Control
ENTER button (page 16 and 28)
Press this button to enter your menu selection or to run
functions. The button acts as the right mouse button if the
Remote control operating indicator lamp
The light flashes when any remote control button other
than the “LASER” button is pressed.
POWER button (page 23)
Mode switch
is set to the Computer position.
FREEZE button (page 25)
Press this button to temporarily freeze the image
presently on the screen.
Turns the projector ON/OFF when the MAIN POWER
switch on the projector is set to “ I ”.
AUTO SETUP button (page 23)
SHUTTER button (page 25)
Press this button to temporarily mute/black out both
audio and video.
Pressing this button automatically corrects picture
positioning on the screen. While the auto setup
feature is active, the message “AUTO SETUP”
appears on the screen.
D.ZOOM (+/-) buttons (page 26)
Any portion of the picture can be enlarged.
VOLUME (+/-) buttons (page 23)
Use these buttons to adjust the volume level from the
internal speakers or line levels on the AUDIO OUT lines.
FUNC1 button (page 35)
Use to select from the functions listed on the “OPTION
2” screen that can be chosen from the MAIN MENU.
ID SET button (page 15)
RGB button (page 23)
Use to toggle through the RGB1, RGB2, and DVI-D
input ports.
LASER button (page 15)
While this button is pressed and held, the remote
control activates its laser transmitter to display a laser
pointer on the screen.
VIDEO button (page 16 and 23)
Use to set the projector ID when multiple PT-L6510E/
L6600E projectors are used in the system.
Mode switch (Computer/Projector) (page 16)
When controlling the projector, set this switch to the
Projector (right) side. When controlling your PC, set
it to the Computer (left) side.
Wired Remote Control port (page 17)
When using wired remote control, connect the remote
control to the projector with the accessory wired
remote control cable.
Use to toggle between the Composite Video and S-
Video ports. The button acts as the Page Down button
if the Mode switch
is set to the Computer position.
MENU button (pages 16, 27 and 28)
Main Menu display is switched on and off alternately
each time this button is pressed. If the menu has
multiple pages, this button may be used to view the
next or previous menu page. The button acts as the
Page Up button if the Mode switch
Computer position.
is set to the
Remote Control Transmitter Window
Whenever operating the Remote Control, aim this window
to the projector's remote control receiver window.
Laser Transmitter Window
Arrow (
) buttons (page 16 and 28)
Use to choose menu items, change settings, or adjust
control parameters. The button acts as a mouse, so
can move the cursor if the Mode switch
the Computer position.
is set to
Click button (page 16)
The button acts as the left mouse button if the Mode
switch
is set to the Computer position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector < Top · Front and Side >
Status LED lights
Status LED lights
Side interface panel
(see page 13)
(Viewed from the rear side)
T
U
O
IN
IN
L
IA
R
E
S
IN
T
IR
U
O
D
E
T
W
U
O
E
T
O
IN
B
M
R
S
E
U
R
2
5
1
U
L
BM
T
IO
D
T
U
O
<
U
C
P
T
B
D
A
U
>
O
G
U
R
A
B
G
IO
R
IN
I
N
IO
D
I
N
U
2
A
B
G
R
O
E
D
V
I
D
V
D
/H
I
N
C
N
O
Y
S
E
ID
-
V
/PB
1
S
-Y
/B
IN
B
B
T
U
G
O
/Y
R
G
/PR
-D
-Y
/R
VI
D
R
Exhaust vents
IN
STAND BY (R) LAMP1 LAMP2
ON (G)
TEMP
Exhaust vents
Speakers
Remote control receiver window (page 14)
Receives IR commands transmitted from the remote
control.
Speakers deliver a total audio output power of 6 watts
(3 + 3 watts each).
Line input (AC IN) socket (page 23)
Connect the accessory line power cord into this
receptacle. Do not connect any other cord to this
socket.
Focus ring (page 23)
For focus adjustment.
Powered focus adjustment is also available.
Projection lens
MAIN POWER switch (page 23)
Use this switch to turn “ I ” “O” the commercial line
power applied to the projector.
Images are projected onto the screen through this
lens.
Lens cap
Burglar lock
Cap the lens whenever the projector is left unused.
Power status light (page 23)
Lit in red when the projector is in standby mode with
MAIN POWER switch set to “ I ”. Lit in green when
the unit is turned ON.
Attach a commercial burglar prevention cable (e.g.
from Kensington) to this lock port. It is compatible
with the Micro Saver Security System from
Kensington. This security lock is compatible with the
Microsaver Security System from Kensington.
Contact details for this company are given below.
Kensington Technology Group ACCO Brands Inc.
2885 Campus Drive San Mateo, CA 94403
Tel (650)572-2700
Lamp 1 monitor (page 40)
Lights when lamp unit 1 requires replacement.
Flashes if the lamp 1 drive circuit is malfunctioning.
Lamp 2 monitor (page 40)
Lights when lamp unit 2 requires replacement.
Flashes if the lamp 2 drive circuit is malfunctioning.
Temperature (TEMP) monitor light (page 40)
Warns of unacceptable internal temperatures. May
be either continuously lit or flashing.
Fax (650)572-9675
Air filter (page 41)
Leveling button (page 24)
Use these buttons (one on each side) to level the
projector when resting on its feet.
Leveling foot (page 24)
Use in conjunction with
adjustment.
for the projector's tilt
(A leveling foot is provided on each side of the unit.)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Location and function of each part
Projector < Top · Rear and Side >
< Rear control panel >
How to open panel lid
Press the
mark on the upper right
corner of the panel lid until it clicks open.
Stack Lid
FOCUS buttons (page 23)
When two projectors are to be stacked, use this lid
for positioning.
Adjust focus with the “ + ” or “ – ” buttons.
AUTO SETUP button (page 23)
Carrying handle
Pressing this button automatically corrects picture
positioning on the screen. While the Auto setup
feature is active, the message “AUTO SETUP”
appears on the screen.
Pull out this handle to carry the unit.
Lamp unit compartment (page 43)
Houses the lamp unit.
MENU button (pages 27 and 28)
Rear side remote control receiver window
(page 14)
Receives commands transmitted from the remote
control.
Main Menu display is switched on and off alternately
each time this button is pressed. If the menu has
multiple pages, this button can be used to view the
next or previous menu page.
Control subpanel lid
ARROW (
) buttons (page 28)
Open this lid to access the control subpanel.
POWER switch (page 23)
Turns the unit ON/OFF.
Use to choose menu items, change settings, or adjust
control parameters.
ENTER button (page 28)
VIDEO button (page 23)
Press this button to enter your menu selection or to
run functions.
Use to select video signal format from composite
video and S-video.
RGB button (page 23)
Use to select RGB signal source from those
connected to the RGB1, RGB2 and DVI ports.
LENS SHIFT buttons (page 24)
Pressing the
or
button tilts the projection lens
to move the picture on the screen up or down
accordingly.
ZOOM buttons (page 23)
Adjust the picture size on the screen with the “ + ” or
“ – ” buttons.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
< Interface panel >
IN
OUT
IN
OUT
L
R
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B/B-Y/PB SYNC/HD
VD
OUT
RGB 1 IN
RGB 2 IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
> PC <
TBMU152
S-VIDEO IN port (pages 19, 20 and 33)
Connect an S-video signal source to this port.
Depend on input signal, screen aspect will
automatically change 16:9 or 4:3.
SERIAL IN port (pages 20, 21, 22 and 37)
Use the RS-232C serial port as an alternative
interface for controlling the projector from your PC.
(D-SUB 9 pin)
VIDEO IN port (pages 20 and 22)
Connect a composite video signal source to this port.
(BNC)
SERIAL OUT port (pages 21 and 22)
The signal applied to the serial input port appears at
this port (9-pin D-sub female connector).
RGB1 (YPBPR) input ports (pages 20, 21 and 22)
Apply RGB or YPBPR video to these ports. (BNC)
RGB2 (YPBPR) IN port (page 21)
VIDEO OUT port (pages 20 and 22)
Composite video signal appears at this port. (BNC)
AUDIO IN L-R jacks (page 20)
Only a single pair of audio inputs is available. Change
connections to these jacks according to your choice
of video source from composite and S-video (RCA
jacks).
RGB video input port. (D-SUB 15 pin)
RGB OUT port (pages 21 and 22)
The signals applied to RGB1 or RGB2 input ports
appear at this port (15-pin D-sub female connector).
REMOTE port (page 39)
This port may be used to control the projector from
the Remote Control set up in Wired mode. (9-pin D-
sub female connector)
RGB AUDIO IN jack (pages 20 and 21)
Only a single pair of audio inputs is available. Change
connections to these jacks according to your choice
of video source from RGB1, RGB2 and DVI-D (M3
jacks).
DVI-D IN port (pages 19 and 21)
DVI-D signals are applied to this port. (24-pin DVI
connector)
AUDIO OUT jack (page 20)
The audio signals applied to the AUDIO IN or RGB
AUDIO IN jacks of this unit appear at this jack. Once
a cable is plugged into this jack, the signal lines to
the internal speakers are cut off. (M3 jack)
USB IN ports (pages 16, 21 and 38)
The remote control can be used as your PC mouse
by connecting the projector to your PC with the
supplied USB cable. (4-pin square connector)
USB OUT ports
DVI-D OUT port (page 21)
The signal applied to the DVI-D input port appears at
this port (24-pin DVI connector).
WIRED IN/OUT ports (page 17)
Use to connect multiple PT-L6510E/L6600E
projectors in a daisy chain to simultaneously control
them from a single wired remote control. (M3 jack)
The control ports on two or more projectors can be
connected to each other for interlocked control
operations. (Type B)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote control unit
Loading batteries
Effective control range
When loading batteries into the battery compartment
of the remote control, make sure that their polarities
are correct.
The remote control should normally be aimed at either
the front or rear remote control receiver window on
the projector (fig. 1). Otherwise it may also be aimed
at the screen, which will reflect commands back to
the projector's front receiver window as illustrated in
figure 2.
1. Open battery compartment lid.
Open lid in the order of steps
and
.
The effective control range is approx. 7 metres (23
feet) immediately in front of the receiver windows.
(Rear)
(Front)
Remote
control
Remote
control
30°
2. Insert the batteries
30°
Into battery compartment, with their polarities
orientated as indicated ( ) in the compartment.
/
30°
[Top view]
30°
15°
Accessory type-AAA dry
batteries (insert the
negative side first).
Remote
control
Remote
control
IN
OUT
L
R
IN
OUT
IN
OUT
IN
OUT
15°
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B
/
B
-
Y
/
P
B
S
Y
N
C
/
H
D
VD
OUT
RGB
1
IN
RGB
2
IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
>
PC
<
TBMU152
15°
15°
[Side view]
fig. 1
Screen
3. Close battery compartment lid.
Replace the battery compartment lid over the
compartment and slide until it clicks.
projector
IN
OUT
L
R
IN
OUT
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B
/
B
-
Y
/
P
B
S
Y
N
C
/
H
D
VD
OUT
GB
1
IN
GB
2
IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
>
PC
<
TBMU152
Remote control
receiver window
(Front)
Remote control
receiver window
(Rear)
Remote
control
fig. 2
Caution
• Exercise care not to drop the remote control
on hard flooring.
Note
• When the remote control is aimed at the
screen, the effective control range may be
reduced due to the optical loss of the screen.
• The remote control may not function properly
if an object is in the light path.
• Exercise care not to spill water or any other
liquid on the remote control.
• Do not use Ni-Cd batteries with this remote
control.
• The remote control receiver may not function
properly in intense ambient light. Carefully site
the projector so its remote control receiver
windows will not be directly exposed to
intense light.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using laser pointer
The remote control contains a laser source that can appear as a coloured spot on the screen which you can use as
a pointer. The laser beam is activated while the “LASER” button is pressed and held.
Warning
DO NOT STARE INTO THE LASER BEAM OR AIM IT AT ANY
PERSON'S EYE. LASER RADIATION CAN CAUSE SERIOUS
INJURY TO THE HUMAN EYE.
Laser Transmitter Window
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
WAVE LENGHT: 640-660nm
MAXIMUM OUTPUT: 1mW
CLASSDHHS
II LARSUELRESPRODUCT
PRODUCT COMPLIES WITH
21 CFR SUBCHAPTER
J
Laser Specifications:
IN EFFECT AS OF DATE OF MANUFACTURE.
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
Operation
indication lamp
MANUFACTURER:
MANUFACTURED:
CAUTION
LASER RADIATION
DO NOT STARE INTO BEAM
B
Wavelength: 640 to 660 nm
Output power: 1 mW (Class 2)
WAVE LENGHT: 640-660nm
MAXIMUM OUTPUT: 1mW
CLASSDIIHLHSARSUELRESPRODUCT
PRODUCT COMPLIES WITH
21 CFR SUBCHAPTER
J
IN EFFECT AS OF DATE OF MANUFACTURE.
MANUFACTURER:
MANUFACTURED:
B
MATSUSHITA ELECTRIC INDUSTRIAL CO.,LTD.
1-1 Matsushita-cho,Ibaraki,Osaka,567-0026,Japan
MODEL NO.:N2QAEA000003
REMOTE CONTROL
MADE IN CHINA
For LCD Projector
MATSUSHITA ELECTRIC INDUSTRIAL CO.,LTD.
1-1 Matsushita-cho,Ibaraki,Osaka,567-0026,Japan
MODEL NO.:N2QAEA000003
REMOTE CONTROL
For LCD Projector
MADE IN CHINA
PUSH
Caution
• Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
• This remote control unit cannot be repaired.
Setting projector IDs for remote control
When controlling multiple projectors individually or simultaneously with a single remote control, projector IDs must
be set into the remote control as described in the following steps:
1. Press the “ID SET” button on remote control.
ID number “ALL” will be displayed on the OSD.
2. Press and hold the “ID SET” button for more than 2 seconds.
The ID number will change into “1”. The “ID SET” button will now toggle through ID numbers “2”, “3”, “ALL”, “1”,
and so on each time it is subsequently pressed.
3. Select the ID number you wish and then press the “ENTER” button.
Note
• The projector ID number in the remote control is set to “ALL” by default. It is therefore not necessary to set a
projector ID number when only one projector is used.
• The projector can be turned ON/OFF from the remote control only if the projector ID is set in the remote
control. For more details on projector ID setting, see page 36.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote control unit
Using the remote control as a PC mouse
You can use the remote control as your PC mouse. Set the Mode (Projector/Computer) switch on the remote control
to Computer and connect the projector's USB port to your PC counterpart with the accessory USB cable.
Projector
OUT
IN
OUT
IN
OUT
IN
UDIO
USB
SERIAL
OUT
WIRED
Accessory
USB cable
PC equipped with
a USB port
RGB 2 IN
RGB OUT
REMOTE
> PC <
TBMU152
• When your PC is attached to the projector for the first time, the “new hardware wizard” will launch automatically.
When USB cable connects for the first time between projector and PC, the following massage appear from PC. The
reason that the driver not installed, therfore press “NEXT” button continuously and finally. Press “Finish”.
The following is in the case of Windows
Note
• If you click “Cancel”, the “new hardware wizard” launches each time your PC is connected to the projector.
Mode switch (Computer/Projector)
Mode switch is set to the Computer position.
• Page button
Page button
: Functions as the Page Up button on your PC
keyboard.
button
: Functions as the Page Down button on your PC
keyboard.
R-CLICK button
• Arrow (
) button
These buttons functions as the cursor control buttons
on your PC.
Click button
Mode switch
(Computer/Projector)
• R-CLICK button
This button functions as the right button on your PC
mouse.
• Click button
This button functions as the left button on your PC
mouse.
Note
• The optional wireless receiver (Model ET-RMRC1) is needed for a PC not equipped with a USB port. However,
Page buttons do not function.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote control in wired mode
Two or more projectors can be controlled from a single Remote Control by connecting the Remote Control to the
projectors with the accessory Wired Remote Control Cable. The wired remote control is particularly useful if the
projector is sited in a place where it is exposed to intense ambient light or if an object blocks the path of IR light from
the Remote Control.
Remote control
Projector's side interface panel
IN
OUT
T
IN
OUT
IN
IO
USB
SERIAL
OUT
RGB 2 IN
RGB OUT
REMOTE
WIRED
> PC <
TBMU152
Remote
control cable
(accessory)
Conversion plug
(accessory)
To a second
projector
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting-up
Projection Schemes
Projection Distances
Unit : m
Height
position: H
Any of the following four projection schemes can be
used with the PT-L6510E/L6600E projector
depending on user's needs or viewing conditions.
Use “OPTION 1” menu (chosen from the MAIN
MENU) to choose the appropriate projection scheme
(see page 34).
Screen Size (4 : 3)
Projection distance: L
Diagonal length Height (SH) Width (SW) Wide (LW) Telephoto (LT)
—
0.76
1.02
1.27
1.52
2.03
2.54
3.05
3.56
4.06
4.57
5.08
5.51
6.10
6.60
7.11
7.62
0.46
0.61
0.76
0.91
1.22
1.52
1.83
2.13
2.44
2.75
3.05
3.35
3.66
3.96
4.27
4.57
0.61
0.81
1.02
1.22
1.63
2.03
2.44
2.84
3.25
3.66
4.06
4.47
4.88
5.28
5.69
6.10
1.4
1.9
2.4
2.9
3.9
4.9
5.9
6.9
7.9
8.9
9.9
10.9
11.9
12.9
13.9
14.9
0.02 to 0.22
0.03 to 0.30
0.04 to 0.38
0.05 to 0.45
0.06 to 0.60
0.08 to 0.76
0.09 to 0.91
0.11 to 1.06
0.12 to 1.21
0.14 to 1.37
0.15 to 1.52
0.17 to 1.67
0.18 to 1.82
0.20 to 1.98
0.21 to 2.13
0.23 to 2.28
1.4
1.8
2.1
2.9
3.6
4.3
5.1
5.8
6.6
7.3
8.1
8.8
9.5
10.3
11.0
Projection Scheme 2
Table standing
Ceiling mount
(Default position)
Setting-up dimensions which are not given in the above
table can be calculated using the formulas below.
If the screen size (diagonal) is SD, then the following
formulas is first used to obtain the screen width (SW).
SW = (SD x 0.0254) x 4 ÷ 5 (SD unit is inches)
The value for SW obtained above can then be used
with the following function to calculate the projection
distance for the wide lens position (LW) and the
projection distance for the telephoto lens position (LT).
LW = 1.831 x SW - 0.071
Installation Geometry
After the projector is roughly positioned, picture size
and vertical picture positioning can be finely adjusted
with the powered zoom lens and lens tilt mechanism.
Side view
LT = 2.449 x SW - 0.066
For 16 : 9 aspect rations, the following formal can be
used to calculate the screen width (SW).
With optional ceiling mount
bracket (ET-PKL6500)
SW = (SD x 0.0254) x 16 ÷ 327
H
Note
L
276
• The dimensions in the table above and the values
obtained from the above formulas may contain
slight errors.
IN
OUT
L
R
IN
IN
OUT
IN
OUT
L
RGB
IN
S-VIDEO IN
R/R-Y/PR
VIDEO
G/Y
A
U
D
I
O
I
N
A
U
D
I
O
A
U
D
I
O
USB
SERIAL
B
/
B
-
Y
/
P
B
S
Y
N
C
/
H
D
VD
OUT
WIRED
RGB
1
IN
RGB
2
IN
R
G
B
O
U
T
REMOTE
IN
OUT
DVI-D
>
PC
<
TBMU152
H
• It is recommended that you use the projection
distance for the wide lens position (except in cases
where the diagonal picture size is 0.762 m).
• The above dimensions are the case when the
aspect ratio is 4:3. When an SXGA signal is input
and projected, the right and left ends of the picture
will be blanked the aspect ratio will be 5:4.
Screen
L: Projection distance
SH: Image height
SW: Image width
H: Distance from centre of lens to bottom
edge of projected image.
Top view
L
87.5
175
Screen
[unit : mm]
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup precautions
• Before connecting any of your video/audio equipment to the projector, carefully read the owners manual supplied
with the equipment once again.
• All cable connections should be made with the entire system devices, including the projector, first turned off.
• Obtain commercial interconnecting cables for devices supplied with no accessory or optional interconnect cables.
• Video signals containing too much jitter may cause the images on the screen to randomly wobble or shake. Inserting
a time base corrector (TBC) in the projector's video line will relieve this problem.
• The projector only accepts composite-video, S-video, analogue-RGB (with TTL sync. level), and digital signal from
PC.
• The projector contains built-in speakers. When greater sound output is required, use an audio amplifier connected
to the projector's AUDIO OUT jack. Once the cable is plugged into the AUDIO OUT jack, the audio signal lines to the
internal speakers are automatically cut off.
• Some PC models are not compatible with the PT-L6510E/L6600E projector.
• The pin assignments on the S-VIDEO IN port are as
follows:
• The pin assignments on the DVI-D input port are as
follows (interface with TMDS port on PC):
Pin No.
Signal
Ground (luminance)
Ground (colour)
Luminance signal
Colour signal
Viewed from mating side
Viewed from mating side
Pin No.
Signal
T. M. D. S data 2-
T. M. D. S data 2+
T. M. D. S data 2/4
shield
Pin No
.
Signal
T. M. D. S data 3+
+5 V
Ground
• The pin assignments on the RGB2 input port are as
follows:
Hot plug sense
T. M. D. S data 0-
T. M. D. S data 0+
T. M. D. S data 0/5
shield
T. M. D. S data 4-
T. M. D. S data 4+
DDC clock
Pin No.
Signal
DDC data
R/PR
G/G · SYNC/Y
T. M. D. S data 5-
T. M. D. S data 5+
T. M. D. S clock
shield
T. M. D. S data 1-
T. M. D. S data 1+
T. M. D. S data 1/3
shield
P
B
SDA
HD/SYNC
VD
T. M. D. S clock+
T. M. D. S clock-
Viewed from mating side
Pin : Not used.
T. M. D. S data 3-
SCL
Pins
Pins
-
,
, and : Ground.
and : Valid if the PC has the corresponding function.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting-up
Example of connecting with AV products
Colour monitor
Laser disc player
Video deck
IN
OUT
L
R
IN
OUT
IN
OUT
IN
OUT
Control PC
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B/B-Y/PB SYNC/HD
VD
OUT
RGB 1 IN
RGB 2 IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
> PC <
TBMU152
Red (Conect PR
)
Blue (Conect PB
)
Green(Conect Y)
Audio equipment
Digital Hi-vision video deck
Note
• Only a single pair of audio inputs (AUDIO IN L-R) is available for the composite and S video, also only a signal
RGB audio input is available for the RGB1, RGB2 and DVI-D. You will need to change audio input connections
depending on your signal selection.
• If your audio equipment is connected to the projector's AUDIO OUT jack, the remote control supplied with the
projector can be used to control volume, balance, and mute on the audio output line.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of connecting with PCs
PC with
PC
Control PC
DVI port
PC with
USB port
USB cable
(Accessory)
DVI Cable (Option)
(ET-SCDV03)
IN
OUT
L
R
IN
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B/B-Y/PB SYNC/HD
VD
OUT
RGB 1 IN
RGB 2 IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
> PC <
TBMU152
*1
IN
OUT
L
R
IN
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B/B-Y/PB SYNC/HD
VD
OUT
RGB 1 IN
RGB 2 IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
> PC <
TBMU152
Colour monitor with
RGB video ports
Caution
• When the projector's main power is turned OFF, also turn OFF all the PCs connected to it.
• *1 An asterisk denotes that the second projector requires positioning if the RGB outputs are connected in a
daisy chain. However, the signals should be divided at the signal source if possible.
Note
• If your PC is not equipped with a USB port, a ET-RMRC1 interface will be needed to use the mouse capability
of the remote control.
• For the specifications of the RGB signals that can be applied from the PC, see the data sheet on page 48.
• If your PC has the resume feature, the computer may not function properly until the resume capability is
disabled.
• Signals applied to the RGB1 or RGB2 ports appear at the RGB OUT port.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting-up
Example of connecting with system switcher
Note PC
Control PC
Video deck
System switcher
POWER
INPUT SELECT
3
VP
ON/OFF
OFF
1
2
4
5
6
ON
OFF
Signal Selector TW-SW
S
J
Digital STB
DVD player
IN
OUT
L
R
IN
OUT
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B/B-Y/PB SYNC/HD
VD
OUT
RGB 1 IN
RGB 2 IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
> PC <
TBMU152
*1
IN
OUT
L
R
IN
OUT
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B/B-Y/PB SYNC/HD
VD
OUT
RGB 1 IN
RGB 2 IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
> PC <
TBMU152
Colour monitor with
RGB video ports
Caution
• *1 An asterisk denotes that the second projector requires positioning if the RGB outputs are connected in a
daisy chain. However, the signals should be divided at the signal source if possible.
Note
• Read the operating instructions for the system switcher carefully.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting to use
T
U
O
IN
T
IN
L
IA
R
E
S
IN
U
O
D
E
IR
T
W
U
O
E
T
I
N
O
B
M
R
S
E
U
R
2
5
1
U
L
BM
T
IO
D
T
U
O
<
U
C
P
T
B
D
A
U
>
O
G
U
R
A
B
IO
G
R
·
·
IN
I
N
IO
D
I
N
U
2
A
B
G
R
O
E
D
V
I
D
V
D
/H
I
N
C
N
O
Y
S
E
ID
-
V
/PB
1
S
-Y
/B
IN
B
B
T
U
G
O
/Y
R
G
/PR
-D
-Y
/R
VI
D
R
IN
·
LEVELING Lever
on each side.
Fit the picture size to the screen size--- [Projector]
Fit the picture size to the screen size with the “ZOOM
(+/-)” buttons on the projector's rear control panel.
Powering Up the Projector
Remove the lens cover.
Plug one end of the accessory power cord into
the projector's power receptacle, and the other
end to a convenient wall outlet. (AC 220-240 V
50Hz/60 Hz)
Repeat steps
through
until the picture
completely fits within the screen bounds.
Adjust focus again with the “FOCUS (+/-)” buttons
on the rear control panel or with the focus ring
on the projection lens.
Press the “ I ” marked side of the MAIN POWER
switch.
The projector will enter standby mode, with the power
status light lit in red.
Adjust the “ZOOM (+/-)” buttons again until the
picture completely fits within the screen bounds.
Powering Off the Projector
Press the “POWER” button on the projector or
“POWER” button on the remote control.
The power indicator on the projector will flash orange.
After a shot period, the indicator will illuminate green.
1. Press and hold the “POWER” button for more than
0.5 seconds or quickly double-press the button. The
projection lamp will turn off, with the power status
light turned to orange.
Making Initial Adjustment /
Setting input port
Roughly adjust the focus with the “FOCUS (+/-)”
buttons on the rear control panel or with focus
ring on the projection lens.
2. Wait until the power status light turns to red (i.e.,
until the cooling fan stops). While the cooling fan is
still running, never switch the MAIN POWER switch
OFF, unplug the projector from the outlet, or open
the main circuit breaker.
Choose the projection scheme (page 34).
Select the input port with the “RGB” or “VIDEO”
button. --- [Projector or remote control]
3. Press the “O” marked side of the MAIN POWER
switch to remove all power from the projector.
Note
RGB1(YPB
P
R1) RGB2(YPB
PR2) DVI
RGB
• If the projector is re-powered while the
projection lamps are cooling down after the last
power off, the lamps will remain off for a short
time before they automatically turn on again
(Power Status light flashing in orange).
VIDEO S-VIDEO
VIDEO
Adjust volume level with the “VOLUME (+/-)”
buttons. --- [Remote control]
• The projector consumes approx. 9 Watts of
power in Standby mode after the cooling fan
stops (Power Status light lit in red).
For volume level control on the projector, see page 27.
If your audio equipment is connected to the AUDIO OUT
jack, the VOLUME control adjusts the line output level.
Adjust the projector's tilt angle (page 24).
Adjust the vertical position of the picture (page 24)
Press the “AUTO SETUP” button --- [Projector or
remote control]
• If you inadvertently shut off the Main Power
switch, the projection lamp may remain off for
some time on re-powering the projector. The
lamp will automatically turn on after a period of
time (Power Status light lit in green).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting to use
Leveling the Projector
<Retracting the Leveling Feet>
For the best viewing result free from distortion, the
projector should be carefully leveled on its base.
Follow the steps below to correct the tilt angle of the
projector when it is installed on a floor-standing base.
While lifting the front side of the projector, raise the
Leveling lever, and then slowly lower the unit.
1. While lifting and holding the front side of
the projector to the level position, pull and
hold the LEVELING button on each side
of the bottom panel until the leveling feet
rest on the projector base surface.
Caution
• Do not press the LEVELING levers without
holding the projector with your hands.
Otherwise, the leveling feet will be unlocked and
the projector may drop rapidly onto the projector
base surface, possibly leading to damage.
LEVELING Lever
LEVELING feet
on each side.
Caution
Adjusting the Vertical Position of
the Picture
The vertical position of the picture can be adjusted
using the electric “LENS SHIFT” buttons on the rear
control panel. Do this adjustment after the projection
distance and projector position have been
determined.
• Keep holding the projector until both leveling
feet touch the base surface.
2. Release the LEVELING levers.
The leveling feet lock in place.
3. Make fine leveling adjustments by
manually turning the leveling feet.
• Adjusting vertical position with the “LENS
SHIFT” buttons:
Press the button to shift
the picture upward.
47 mm
Note
IN
OUT
L
R
IN
OUT
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B
/
B
-
Y
/
P
B
S
Y
N
C
/
H
D
VD
OUT
RGB
1
IN
RGB
2
IN
RGB OUT
REMOTE
WIRED
• The maximum length of the leveling foot is 47
mm. If it is rotated on reaching that length it will
turn freely without extending further.
IN
OUT
DVI-D
>
PC
<
TBMU152
Press the button to shift
the picture downward.
• If the picture has keystone distortion, do
keystone adjustment from the menu. (page 32)
• Adjusting vertical position from the menu:
Alternatively, you can adjust the vertical position of
the picture by choosing the “LENS SHIFT” option
from the “OPTION 1” menu chosen from the MAIN
MENU (see page 34).
Caution
When shifting the lens, be careful not to
catch your fingers between the lens and
shroud.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Advice on the installation of exhaust guides
Hot air from the cooling fan vents may in rare cases cause disturbances to the screen image.
If this should occur, install the attached exhaust guides.
Fixing pin (2 sets)
Left-side exhaust guide
Right-side exhaust guide
1. Identify the left-side and right-side
exhaust guides, then insert the tabs of
the relevant guide into the holes on the
front of the projector.
2. Insert the fixing pins from the bottom
of the projector and tighten them
securely.
Using the Freeze function
The picture freezes each time you press the remote control “FREEZE” button.
Still image
Motion image
(FREEZE)
Using the Shutter function
The shutter function can be used to momentarily turn off the picture and sound from the projector when the projector
is not being used for short periods of time, such as during breaks in meetings or when carring out preparation. The
projector uses less power in shutter mode than it does in normal projection mode.
1. Press the remote control/ “SHUTTER” button to mute both picture and sound.
Both video and audio are turned off.
2. To clear muting, press any button on the remote control or projector.
Apear the picture and sound.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Digital Zoom (D.ZOOM +/-) function
A specific portion of the picture presently on the screen can be zoomed in on with the remote control/ “D.ZOOM (+/
-)” buttons. You may find it useful for highlighting a specific object during your presentation.
< For PT-L6510E >
1. Press the remote control Digital Zoom
(D.ZOOM +/-) buttons.
Product
1999
2000
%
The projector enters Highlight mode as illustrated on the
left.
A
B
C
D
110
%
110
131
64
122
106
76
E
18
5%
81
%
%
%
%
D
A
47 13%
119
112
69
122
2. Use the arrow (
) buttons to highlight
C
32%
76
42
47
29%
21%
the portion you wish to zoom in on.
E
26
18
-1
B
106
ADJ
-
5
3. Press the “ENTER” button.
The highlighted portion will now be enlarged 2.0 times to
the size of the full screen.
TOTAL
100%
368
368
4. Change the magnification with the “D.ZOOM
A
B
C
D
(+/-)” buttons.
RGB signal input : Over the range of 1.0 to 3.0 times in 0.1
110
131
64
steps.
Video signal input : Over the range of 1.0 to 2.0 times.
5. To restore the original image, press the
2
“MENU” button.
32%
Pressing the “MENU” button will not return the screen to
Highlight mode. To return to Highlight mode, temporarily
exit Zoom mode, then press the “D.ZOOM (+/-)” button
again.
42
< For PT-L6600E >
1. Press the Remote Control/“D.ZOOM +/-”
button.
Product
1999
2000
%
The centre portion of the picture will be magnified.
A
B
C
D
110
%
%
%
%
%
110
131
64
122
106
76
E
D
18
5%
81
2. Change magnification with the “D.ZOOM +/-”
A
47 13%
119
112
69
122
button:
C
32%
76
42
47
29%
21%
Magnification can be changed from 1.0 to 3.0 times for RGB,
and 1.0 to 2.0 times for composite or S-video, all in 0.1
E
26
18
-1
B
106
ADJ
-
5
TOTAL
100%
368
368
steps.
3. The enlarged portion of the picture can be
shifted with the , , , or buttons.
The highlighted portion will now be enlarged 2.0 times to
the size of the full screen.
A
B
C
D
110
131
64
4. Press the “MENU” button to return to the
normal picture.
2
32%
42
Caution
• If the input video signal format is changed while in Zoom mode, the projector will exit Zoom mode.
• PT-L6600E does not have a highlight indication.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen menus
Menu screens
Menus are extensively used for configuring, adjusting, or reconfiguring the projector. The menu structure is as
follows:
MAIN MENU (PT-L6510E)
MENU
INDEX WINDOW FUNCTION (Page 29)
INDEX WINDOW
PICTURE
PICTURE (Pages 30 and 31
)
POSITION
AUDIO
ZOOM/FOCUS
LANGUAGE
When on RGB/YPBPR/DVI signal is being input
PICTURE
PICTURE MODE
COLOUR
NATURAL
32
OPTION
OPTION
SELECT
1
2
BRIGHT
32
CONTRAST
SHARPNESS
32
00
ENTER
W-BAL
W-BAL
W-BAL
SIGNAL MODE
STANDARD
R
G
B
32
32
32
Note
• PT-L6600E does not
have "INDEX WINDOW"
function.
XGA
SELECT
ADJ
ESC
OPTION 2 (Pages 35 and 36
)
OPTION
2
When on S Video/Video signal is being input
LAMP POWER
LAMP SELECT
LAMP RUNTIME
HIGH
DUAL
PICTURE
PICTURE MODE
COLOUR
TINT
NATURAL
32
32
32
32
08
1
7
MUTE
ALL
H
FUNCTION
SET ID
1
BRIGHT
USER MODE
CONTRAST
SHARPNESS
TV-SYSTEM
STANDARD
SELECT
ADJ
ESC
AUTO1
OPTION 1 (Page 34)
SELECT
ADJ
ESC
OPTION
1
OSD
RGB FORMAT
LENS SHIFT
OFF ON
Y•PB•PR
POSITION (Pages 32 and 33
)
When on RGB/YPB
P
R
signal is being input
BACK COLOUR
FRONT/REAR
DESK/CEILING
BLUE
FRONT
DESK
POSITION
H-POSI
128
SELECT
ADJ
ESC
V-POSI
64
34
32
1
DOT CLK
CLK PHASE
KEYSTONE
V-LINEARITY
ASPECT
LANGUAGE (Page 33)
32
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
ENGLISH
STANDARD
SELECT
ENTER
ESC
When on S Video/Video signal is being input
POSITION
H-POSI
V-POSI
VIDEO SIZE
KEYSTON
V-LINEARITY
32
16
32
1
SELECT
ENTER
ESC
ZOOM/FOCUS (Page 33)
32
4
:
3
ASPECT
STANDARD
VOLUME ADJUSTMENT
AUDIO
SELECT
ENTER
ESC
VOLUME
10
ENTER
ESC
Press the “ENTER” botton, and
the press the and bottons
to adjust the volume level.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
On-screen menus
Basic Menu Operations
Returning to the Previous Page
1. Press the “MENU” button.
The MAIN MENU appears on the screen.
(e.g. : MAIN MENU for the PT-L6510E)
• Pressing the “MENU” button returns the screen to the
previous menu page.
• When the MAIN MENU is on the screen, pressing the
MENU button clears all menus from the screen.
MENU
INDEX WINDOW
PICTURE
Menu Items Shown with White Characters
• Some menu items may not be valid for some signal
formats applied to the projector. Invalid menu items
are shown in white letters and the “ENTER” button
remains ineffective to those items.
POSITION
AUDIO
ZOOM/FOCUS
LANGUAGE
OPTION
OPTION
SELECT
1
2
Menu Items Setting
The bottom prompt line differs on each menu
ENTER
depending on the selected menu option:
2. Select (highlight) the desired item with the
or buttons.
• The prompt “
adjustment.
ADJ” is displayed for direct
ENTER” appears for a separate
Selected items are displayed in yellow.
• The prompt “
bar graph.
MENU
INDEX WINDOW
PICTURE
Reset the Factory Default
If the “STANDARD” option in the “PICTURE” or “POSITION”
menus is chosen, or the “STANDARD” option in the remote
control's “FUNC1” button menu is chosen, all the parameter
values in the menu are reset to the factory default.
• Default Setting in Menu
When all the parameter values in the menu are reset
to the factory default, a “STD” indicator appears on
the upper right corner of the menu.
POSITION
AUDIO
ZOOM/FOCUS
LANGUAGE
OPTION
OPTION
SELECT
1
2
ENTER
3. Press the “ENTER” button to enter your
PICTURE
STD
selection.
PICTURE MODE
COLOUR
NATURAL
32
The submenu for the selected option will now open.
BRIGHT
CONTRAST
SHARPNESS
32
32
00
32
32
32
(e.g. : PICTURE Menu)
PICTURE
PICTURE MODE
COLOUR
NATURAL
32
W-BAL
W-BAL
W-BAL
R
G
B
BRIGHT
32
CONTRAST
SHARPNESS
32
00
SIGNAL MODE
STANDARD
XGA
W-BAL
W-BAL
W-BAL
R
G
B
32
32
32
• Default Setting on Bar Graph
SIGNAL MODE
STANDARD
XGA
If the parameter value on a bar graph is reset to the
factory default, the bar turns to green.
SELECT
ADJ
ESC
4. Highlight the desired adjustment item with
the or buttons, then change the
Note
parameter value with the or buttons.
An individual bar graph as shown in the following
figure is displayed for each adjustment item.
• The upper and lower triangular markings on a
bar graph indicate the default setting for the
parameter. If no such triangular markings are
shown on the bar graph, the parameter cannot
be reset to the factory default.
BRIGHT
32
• If no button is operated for approx. 5 seconds while a
bar graph is displayed, the screen will return to the
previous page.
Indicates the
Indicates the current
parameter value.
factory default.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the INDEX WINDOW function
(PT-L6510E only)
The picture presently on the screen can be saved to memory as a still image. The saved image can then be shown
alongside a moving image in a split screen (index window).
Note
• The aspect ratio of each half of the split screen is
Moving
image
Still
2:3, with the image height extended by 1.5 times
the normal height by default.
image
ESC
1. Select the “INDEX WINDOW” from menu
and press the “ENTER” button.
Moving
image
Moving
image
Still
Still
Moving
image
Still
image
image
image
ESC
ESC
ESC
2. Change the picture height with the
button.
or
x 1
x 1,5
(Standard)
x 2
• The picture height can be changed at a
Moving
image
Moving
image
Still
image
Still
image
magnification of x1, x1.5, or x2.0 times.
ESC
ESC
3. The still and motion images can be
swapped with the
or
button.
4. Press the “ENTER” button to save the
split screen image to memory as an index
window image.
Caution
• As you change the screen size, the aspect ratio of the picture also changes. Carefully read the caution for S1
signals on page 33 before changing the screen size.
Note
• When you execute steps 2 and 3 above, the memory is temporarily cleared and the index window image is
saved to memory.
• If the input signal format is changed while an index window is on the screen, the projector will exit the index
window mode.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the picture
1. Obtain the MENU window and select
(highlight) the desired option item with
COLOUR
(Valid for composite/S-video/YPBPR signals only)
button: Deepens colours.
button: Weakens colours.
the
or
buttons.
2. Adjust the parameter value with the
or
buttons. For items requiring a separate
bar graph, first display the bar graph with
TINT
(Valid for NTSC / NTSC4.43 standard)
the “ENTER” or
/
buttons, then
“TINT” is used to adjust human skin.
button: Adjusts skin tone toward greenish colour.
button: Adjusts skin tone toward reddish-purple.
adjust the parameter value with the
buttons.
or
Note
• For RGB/YPBPR/DVI signals
• PT-L6600E is able to adjust the tint level at
YPBPR input mode.
PICTURE
PICTURE MODE
COLOUR
NATURAL
32
BRIGHT
CONTRAST
SHARPNESS
32
32
00
32
32
32
BRIGHT
“BRIGHT” is used to adjust the black level
(brightness).
W-BAL
W-BAL
W-BAL
R
G
B
button: Raises the picture brightness.
button: Lowers the picture brightness.
SIGNAL MODE
STANDARD
XGA
SELECT
ADJ
ESC
CONTRAST
“CONTRAST” is used to adjust the contrast ratio.
• For composite or S-video signals
button: Raises the contrast ratio.
button: Lowers the contrast ratio.
PICTURE
PICTURE MODE
COLOUR
TINT
NATURAL
32
32
32
32
08
SHARPNESS
(Valid for composite/RGB/YPBPR signals only for PT-
L6510E)
(Valid for composite/YPBPR signals only for PT-
L6600E)
BRIGHT
CONTRAST
SHARPNESS
TV-SYSTEM
STANDARD
AUTO1
“SHARPNESS” is used to adjust the crispness of the
image.
SELECT
ADJ
ESC
button: Sharpens the edge of the image.
button: Softens the edge of the image.
PICTURE MODE
The picture mode can be selected from the following
depending on viewing conditions and the video signal
source in use:
PICTURE MODE
NATURAL
DYNAMIC
NATURAL: Picture brightness/contrast ratio is
adjusted to that suitable for projection
image viewing under typical location
conditions.
DYNAMIC: Picture brightness/contrast ratio is
increased to suit brighter viewing
environments.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TV-SYSTEM
(for composite/S-video only)
SIGNAL MODE
(for RGB/YPBPR/DVI signals only)
TV-SYSTEM
AUTO1
“SIGNAL MODE” displays the names of the signals
(resolution) presently applied to the RGB or YPBPR
input ports. For details of signal names, see the table
on page 48.
If the user mode is registered, the following menu
will appear. You can choose either “AUTO” or a
registered user setting from “USER1” to “USER3” with
AUTO2
NTSC
NTSC4.43
PAL
the
or
buttons.
SIGNAL MODE
AUTO
PAL-M
PAL-N
If “AUTO” is chosen, a setting closest to the user
setting is automatically selected. (In the example
above, only “USER1” is registered for user address.)
SECAM
AUTO1: Automatically selects the TV standard that
matches the input video signal, out of NTSC,
PAL, NTSC4.43, and SECAM.
AUTO2: Automatically selects the TV standard that
matches the input video signal, out of NTSC,
PAL-M, and PAL-N.
Note
• If you choose a user address registered for a
signal that does not match the input signal, it is
regarded as “no signal”, and the projector will
display the specified background colour.
• Normally “AUTO1” or “AUTO2” should be chosen for
this option.
• If input video signal quality is poor, choose the TV
system that matches the input video signal.
STANDARD
Pressing the “ENTER” button resets all the
adjustment parameter values to the factory default
values, with a “STANDARD” indicator shown on the
upper right corner of the menu.
Automatically selected by detecting the horizontal/vertical
scan frequencies and colour sub-carrier listed in the table
below:
H. Scan
V. Scan
Colour
Table
Frequency Frequency Subcarrier
(kHz)
15.75
15.75
15.63
15.75
15.63
15.63
(Hz)
(MHz)
NTSC
NTSC4.43
PAL
60.00
60.00
50.00
60.00
50.00
50.00
3.58
4.43
PAL-M
PAL-N
3.58
SECAM
4.25 or 4.41
W.BAL (White balance) R/G/B
(for RGB/DVI signals only)
White balance may be adjusted for each colour to
correct reddish or bluish tones in white portions of
the picture:
button: Deepens the selected colour.
button: Weakens the selected colour.
Note
• Separate sets of adjustment parameters can
be saved for the RGB1, RGB2 and DVI inputs.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the position
1. Obtain MENU window and move highlight
cursor up and down through the menu
CLK PHASE (for RGB signals only)
Adjust clock phase after you are finished with dot
clock adjustment.
Clock phase adjustment allows the user to minimize
with the
2. Adjust parameter value for the selected
item with the or button. For items
or
button.
visible noise with the
or
button.
Note
that call for a separate bar graph, first
• A noise may not disappear when adjusting the
dot clock or clock phase at UXGA signal mode.
• Clock phase is adjustable for each of R, G,
and B signals. Final parameter values are
saved to memory.
show the bar graph with the “ENTER” or
/
button, then adjust parameter value
with the or button.
• RGB/YPBPR/DVI signals
• Clock phase adjustment is not available for
digital RGB signals.
POSITION
H-POSI
V-POSI
128
64
34
32
1
DOT CLK
CLK PHASE
KEYSTONE
V-LINEARITY
ASPECT
KEYSTONE
Keystone distortion can be corrected only along either
32
STANDARD
horizontal bound of the picture:
SELECT
ENTER
ESC
button:
button:
• Composite/S-video signal
POSITION
H-POSI
V-POSI
VIDEO SIZE
KEYSTON
V-LINEARITY
32
16
32
1
32
4
:
3
ASPECT
STANDARD
SELECT
ENTER
ESC
HORIZONTAL POSITION (H.POSI)
button: Shifts the picture to the right.
button: Shifts the picture to the left.
Note
•
Keystone distortion can be corrected to ±20˚ of
the angle of tilt for the projector. However, the
greater the correction amount,the more the picture
quality will deteriorate, and the harder it will
become to achieve a good level of focus. To obtain
the best picture quality, set up the projector and
screen in such a way that the amount of keystone
correction required is as minimal as possible.
VERTICAL POSITION (V.POSI)
button: Shifts the picture upward.
button: Shifts the picture downward.
VIDEO SIZE
(Vaild for composite video/S-video only)
button: Increases picture size.
button: Reduces picture size.
• The picture size will also change when
correction of keystone distortion is carried out.
DOT CLK
(Vaild for RGB signals only)
V. LINEARITY
Fine, regular patterns on the screen may be disturbed
by fine stripe noise called moire. Dot clock adjustment
allows the user to minimize this moire.
After you are finished with keystone adjustment,
adjust vertical linearity with the or button.
Vertical linearity is not adjustable if no correction was
made to keystone distortion.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Zoom/Focus
ASPECT
ZOOM
Aspect ratio is adjustable only for composite video,
S-video, or YPBPR signals complying with the NTSC
(480i or 480p) or PAL (625i) standards.
“ZOOM” is used to adjust projected picture size.
button: Increases picture size.
button: Reduces picture size.
When the picture size reaches the upper or lower
limits, the colour of the arrows on the four corners
will change from light blue to red.
ASPECT
AUTO
16
4
:
9
:
3
S
4
:
3
[AUTO]: (S-video only)
If an S1 video signal is applied to the S-VIDEO
port, the picture is automatically switched to
the 16:9 aspect ratio.
ZOOM
FOCUS
[16:9]: The image is vertically compressed into a 16:9
ratio.
[4:3]: The aspect ratio inherent to the input video signal
is left intact when projected onto the screen.
[S4:3]: Picture size is compressed to 75% of the
original picture size when projected. (This
mode is useful when viewing pictures with the
standard 4:3 aspect ratio on a wide screen
with the 16:9 aspect ratio.)
FOCUS
“FOCUS” is used to adjust picture focus with the
or buttons.
Changing the display language
What Is S1 Video?
•
The S1 video is the wide-aspect-ready S-video format
containing an aspect sense signal for squeezed videos fed
from video equipment.
• If "AUTO" is chosen, the projector automatically compresses
the squeezed input video into the 16:9 aspect ratio if it detects
the aspect sense signal.
1. Highlight the desired language with the
or
buttons (on the projector or
remote control).
2. Press the “ENTER” button to enter your
selection.
Caution
•
If you choose an aspect ratio that does not match
the source video's aspect ratio, you will see a picture
with an aspect ratio not the same as that of the
original picture. Choose the appropriate aspect ratio
carefully to match that of the original picture.
Menus, setting items, adjustment screens, and control
button names will be displayed in the language the
user chooses.
The available languages are:
English, Deutsch, Français, Español, Italiano,
and
.
Note
Currently chosen language
is displayed here.
•
If the picture size is compressed or enlarged by
using the 16:9 aspect ratio when the projector is
used for profitable purpose or in the presence of
an audience (for example, in a coffee shop or at
a hotel etc.), it may infringe the rights of the
copyright owner of the original picture.
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ESPAÑOL
ITALIANO
ENGLISH
•
If a picture with the standard (4:3) aspect ratio is
projected at a wide aspect ratio, parts of the picture
may run over the screen bounds or the overall picture
may be distorted. To view the picture at its original
aspect ratio, choose the standard 4:3 aspect ratio.
SELECT
ENTER
ESC
Note
• The projector's on-screen display is set to the
English language by default.
STANDARD
Pressing the “ENTER” button resets parameter
values for all the menu items to the factory default,
with a "STANDARD" indicator shown in the upper right
corner of the menu.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION 1 settings
1. Obtain the MENU window and select
(highlight) the desired adjustment item
with the or buttons (on the projector
or remote control).
BACK COLOUR
“BACK COLOUR” is used to choose the background
colour from blue or black when no signal is applied to
the video input ports:
BACK COLOUR
BLUE
2. Adjust the parameter value for the
selected item with the
or
buttons.
BLUE: Sets background colour to blue.
BLACK: Sets background colour to black.
OPTION
1
OSD
RGB FORMAT
LENS SHIFT
OFF ON
Y•PB•PR
Note
• If a signal with unknown or unidentifiable format
is applied, it will be regarded as no signal and
the screen be set to the selected background
colour.
BACK COLOUR
FRONT/REAR
DESK/CEILING
BLUE
FRONT
DESK
SELECT
ADJ
ESC
OSD (On-Screen Display)
PROJECTION SCHEME 1
PROJECTION SCHEME 1 is used to choose the
appropriate projection scheme from Front and Rear:
ON: The name of the signal applied is displayed in
the upper left corner of the screen whenever
the input signal source is switched from one to
another.
FRONT/REAR
FRONT
OFF: The signal name is not displayed even when
an input source switching occurs.
FRONT: Choose this option if pictures are projected
from the front of a reflective screen.
RGB FORMAT
“RGB FORMAT” is used to select the video signal
format depending on the signal applied to the RGB1
or RGB2 port: Only HDTV (1080i)
REAR: Choose this if pictures are projected from
the back of a translucent screen.
PROJECTION SCHEME 2
PROJECTION SCHEME 2 is used to choose the
RGB FORMAT
RGB
appropriate projection scheme from Floor and Ceiling:
Y•PB•PR
DESK/CEILING
DESK
LENS SHIFT
“LENS SHIFT” is convenient for adjusting vertical
picture position in situations where the projector is
not easily accessible.
FLOOR: Choose this option if the projector is installed
on a floor-standing base.
CEILING: Choose if the projector is installed on the
ceiling using the optional ceiling mount
bracket.
LENS SHIFT
button: Shifts the picture upward.
button: Shifts the picture downward.
Note
• The screen picture move reverse direction
when press the or button under the ceiling
set up condition.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION 2 settings
1. Obtain the MENU window and select
(highlight) the desired adjustment item
with the or buttons (on the projector
or remote control).
Note
•
When the currently active lamp exceeds 2000 hours of
cumulative operating time, if in “SINGLE 1” or “SINGLE
2” mode, the other lamp takes over, provided that the
cumulative operating time of that lamp does not exceed
2000 hours.If the cumulative operating time of the other
lamp also exceeds 2000 hours when in “DUAL”,
“SINGLE”, “SINGLE 1”, or “SINGLE 2” mode, the
projector will enter Standby mode after 10 minutes.
If only one lamp is installed in the projector, set lamp
mode to either “SINGLE 1” or “SINGLE 2”. “SINGLE 1”
or “SINGLE 2” is selected. If the corresponding lamp is
not installed, the other lamp will turn on. The same holds
for “SINGLE 2” mode. If “SINGLE” mode is selected, it
may take approx. 90 seconds before the lamp turns
ON.
2. Adjust the parameter value for the
selected item with the
or
buttons.
OPTION
2
LAMP POWER
LAMP SELECT
LAMP RUNTIME
HIGH
DUAL
7
MUTE
ALL
1
H
•
FUNCTION
SET ID
1
USER MODE
SELECT
ADJ
ESC
LAMP POWER
“LAMP POWER” is used to change the luminance of
the projection lamp depending on user's needs or the
LAMP RUNTIME
viewing conditions.
LAMP POWER
HIGH
“LAMP RUNTIME” is used to cheque the cumulative
STANDARD
operating hours of the two projection lamps.
LAMP RUNTIME
1
11
H
HIGH: Choose if a higher picture brightness is required.
STANDARD: Choose for normal picture brightness.
Note
“1”: Lamp 1 operating hours is displayed.
“2”: Lamp 2 operating hours is displayed.
•
If it is not necessary for picture brightness to be very
high (in a small meeting room, etc.), it is advisable
that you set BRIGHTNESS to “STANDARD”. This will
save power consumption and extend lamp life.
Note
• If the cumulative operating hours exceeds 1800
hours, the hour indicator flashes in red.
LAMP SELECT
“LAMP SELECT” is used to choose from Single Lamp
and Dual Lamp modes depending on user's needs
or viewing conditions. In Single Lamp mode, the
projector may automatically select either lamp from
the 2 lamps, or the particular lamp can be specified.
SETTING FUNCTION 1 [FUNC 1]
FUNCTION 1 is used to specify the function of the remote
control / “FUNC1” button. (“FUNC1” button functions differ
between the PT-L6510E and PT-L6600E.)
• PT-L6510E
LAMP SELECT
DUAL
*
Press and hold the “ENTER”
button for approximately 3
seconds. (lamp with longer
operating hours is turned
off)
FUNCTION
1
INDEX
SINGLE
MUTE
SINGLE
SINGLE
1
• PT-L6600E
2
FUNCTION
1
MUTE
DUAL: Two lamps are used simultaneously.
SINGLE: One of either lamps is used (lamp with
shorter operating hours is automatically selected).
SINGLE 1: Lamp Unit 1 is always used.
INDEX: Pressing the “FUNC1” button displays both
still and motion images on a split screen
(same as the “INDEX WINDOW” option in
the MAIN MENU).
SINGLE 2: Lamp Unit 2 is always used.
Caution
MUTE: Pressing the “FUNC1” button mutes the sound
output.
•
Lamp can be selected without turning off the
projector.
STANDARD: Pressing the “FUNC1” button resets all
the parameter values now in the menu
to the factory default, with a
“STANDARD” indicator shown in the
upper right corner of the menu.
•
If lamp mode is switched from “SINGLE”,
“SINGLE 1”, or “SINGLE 2” into “DUAL”, be sure
to temporarily turn the projector OFF, then turn it
ON again. The “DUAL” mode will become valid
only after the projector is turned back ON.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION 2 settings
SETTING UNIT ID
UNIT ID is used to set projector IDs when the user
wishes to control two or more projectors either
simultaneously or separately.
Registering/Deleting/
Displaying User Mode
(For RGB/YPBPR signals only)
Once adjustment settings are registered with User
Mode, they are automatically loaded each time the
projector is powered up. It is not necessary to readjust
settings at every power on.
SET ID
ALL
1
2
3
Registering User Mode
(e.g. Registering positioning data with “USER1”)
1. Apply an input signal you want to register, and
then adjust the picture position, size, and others.
2. Choose “USER MODE” on “OPTION2” and press
the “ENTER” button.
"ALL": The projectors can be simultaneously
controlled from any remote control regardless
of their ID settings.
"1": The projector can be controlled from the remote
control with its projector ID set to “1”.
"2": The projector can be controlled from the remote
control with its projector ID set to “2”.
USER MODE
ENTRY
USER1
"3": The projector can be controlled from the remote
control with its projector ID set to “3”.
3. Choose “USER1” using the
press the “ENTER” button.
or
buttons and
Note
Note
• Unit ID is set to “ALL” by default. Hence ID
number need not be set when only one
projector is used.
• The user address has “USER1” to “USER3”.
4. After recognizing the flashing of the USER1
address display, press the “ENTER” button again.
5. The above adjusted settings has been registered
with “USER1”. Similarly you can also register
settings with “USER2” or “USER3”.
• If the projectors are given ID numbers, their
remote controls must be assigned the same
ID numbers, respectively.
• If the unit IDs of two or more projectors are
set to “ALL”, the user will not be able to
control them separately.
Deleting User Mode
• The projector can be turned ON/OFF from
the remote control only if the projector ID is
set in the remote control. For the details of
projector ID setting, see page 15.
(e.g. Deleting the data of “USER1”)
1. Choose “USER MODE” on “OPTION2” and press
the “ENTER” button.
2. Choose “DELETE” using the
or
buttons.
3. Choose the address (USER1) you want to delete
data from using the or buttons and press the
“ENTER” button.
USER MODE
ENTRY
DELETE
USER1
USER1
4. After recorgnizing the flashing of the address
display, press the “ENTER” button again to delete
the data of the address.
Displaying User Mode
The User Mode can be displayed by following the
steps described in “SIGNAL MODE” on page 31.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SERIAL
The projector is equipped with an RS-232C standard serial terminal at the rear. It is therefore possible to connect it
to a computer for control.
Unit 1 interface panel
Unit 2 interface panel
Connection
• Single
Side interface panel
D-sub 9-pin
D-sub 9-pin
D-sub 9-pin
D-sub 9-pin
• Plural
(female)
(male)
(female)
(male)
IN
OUT
IN
OUT
PC
PC
D-sub 9-pin (female)
SERIAL
SERIAL
SERIAL
D-sub 9-pin
(male)
D-sub 9-pin D-sub 9-pin
(male)
(female)
Communication cable
D-sub 9-pin (male)
Communication cable
Communication cable
Pin assignments and signal names
Description
Description
Pin No.
Pin No. Signal name
Signal name
NC
NC
Receive data
Send data
NC
Send data
Receive data
TXD
RXD
RXD
TXD
Connected internally
Ground
Ground
NC
GND
GND
NC
Connected
internally
NC
Connected
internally
NC
D-Sub 9-pin (female)
external appearance
CTS
RTS
D-Sub 9-pin (male)
external appearance
RTS
CTS
Communication
requirements
Signal level
Sync method
Baud rate
RS-232C
Start-stop transmission
9 600 bps
None
8 bit
Parity
Character length
Stop bit
1 bit
X parameter
S parameter
None
None
Basic format
Transmission from the computer begins with STX, then the command, parameter and ETX are sent in this order.
Colon (:) is not required when transmitting the command which does not need a parameter.
STX
AD
I 1 I 2
:
C1 C2 C3
:
P1 P2 P3 P4 P5
ETX
ID characters
(2 Bytes)
Colon
Colon
Command 3 characters
(3 Bytes)
Parameter
(1 to 5 Bytes)
End
Start
00 to 99
ID designate
Caution
• On commencement of lamp lighting, commands cannot be sent or responses received for approximately 10
seconds. Be sure to send any commands and receive responses 10 seconds. (Applies to the PT-L6600E /
PT-L6600EL only)
• When transmitting several commands, wait for a response from the projector before sending the next command.
When sending commands without parameters, a colon is not necessary.
• When it is unnecessary to designate an ID code, send the format without the part to ID designate it.
Note
• If a wrong command is received, the projector sends ER401 back to the computer.
• When using control from the remote terminal, commands cannot be received at the serial terminal.
• Projector ID supported on the RS-232C interface is 0 (ALL) to 99.
•
The remote control ID is set from 0 to 3. If a command is sent with a projector ID specified, the projector will return
answer back only if the ID contained in the command matches the projector ID or the projector ID is set to ALL.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SERIAL
Control command
When controlling the projector using a computer, commands are as follows:
Remarks
Command
Control contents
Power ON
During standby mode, commands other than PON are invalid.
• While the lamp is ON and being controlled, the PON command is invalid.
PON
•
After turning the lamp OFF, if the PON command is sent during cooling fan
operation, lighting control will function for approximately 95 seconds (PT-L6510E) or
40 seconds (PT-L6600E) after turning OFF to protect the lamp.
POF
AVL
Power OFF
Volume
Parameter
000 = Adjustment value 0
063 = Adjustment value 63
Parameter
0 = Mute (audio mute) off
AMT
IIS
Mute (audio mute)
1 = Mute (audio mute) on
Parameter
VID = VIDEO
RG1 = RGB1
Switch input modes
SVD = S-VIDEO
RG2 = RGB2
DVI = DVI
Parameter
0 = RGB
Parameter
0 = Standby
2 = Lamp lit
ORF
Q$S
Switch RGB 1 · 2 input signals
Check lamp lighting condition
1 = YPB
P
R
(Only 1080i input)
1 = Lamp lighting control
3 = Lamp off control
Parameter
0 = Lamp 1 and 2 off
2 = Lamp 2 on
1 = Lamp 1 on
3 = Lamp 1 and 2 on
QLS
Check lamp lighting condition
Parameter
0 (ALL) to 99
OSI
SET ID
Freeze
Parameter
0 = Freeze off
OFZ
1 = Freeze on
OMN
OEN
OCU
OCD
OCL
OCR
OAS
OSH
DZU
DZD
FC1
Menu
Enter
Cursor up
Cursor down
Cursor left
Cursor right
Auto setup
Shutter
D.Zoom up
D.Zoom down
Function 1
Computer
(DTE specifications)
Cable specifications
Projector
< Connecting to a computer >
1
2
3
4
5
6
7
NC
NC
1
2
3
4
5
6
7
8
9
NC
NC
NC
NC
Caution
• Purchase an appropriate communication
cable to connect a computer to the serial
terminal.
8
9
NC
NC
USB control
The same control as RS-232C can be performed using USB. Need to prepare device driver and control software.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the remote terminal
Using the remote terminal built into this projector, it is possible to operate the projector from an external location
from where infrared remote control signals cannot be received, by using a remote control panel.
Example of a control panel layout
ON
Remote terminal ON / OFF
OFF
ON
STANDBY
RGB
LAMP
VIDEO/
S-VIDEO
RGB/VIDEO
S-VIDEO
RGB2
VIDEO
RGB1
INPUT SELECT
VIDEO
RGB
DVI
Projector set up in a meeting room
DVI switch
Control panel located in a different room
Pin assignment and control
Short pin 1 and pin 9 when controlling.
D-Sub 9-pin (female)
Description
external appearance
Pin No.
Name
Short with pin
Open
Remoto terminal ON / OFF On
Off
Lamp
On
Off (standby)
RGB
RGB/VIDEO
VIDEO
S-VIDEO
RGB2
(
When is VIDEO
)
(
(
(
(
When is VIDEO
)
VIDEO
RGB1
VIDEO
RGB
Switch input modes
(When is RGB
)
When is RGB
When is VIDEO
When is RGB
)
)
Switch DVI modes
DVI
(When is RGB
)
)
Note
• The “POWER”, “RGB” and “VIDEO” buttons on the remote control and projector will not operate when pins
1 and 9 are shorted. RS-232C commands will also be ignored.
• Do not short pins. 1, 2, 3, 5 or 6 when pin 9 is open. If this is done, the projector will ignore signals from the
remote control.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Indication of lamp monitor
This projector is equipped with 3 indicators to show when a lamp needs replacement or there is an abnormal
internal temperature. These lamps flash or light up to indicate a problem.
Turn the power off and follow the steps below.
Lamp 1 monitor (LAMP 1)
T
U
O
IN
IN
L
IA
R
E
S
Lamp 2 monitor (LAMP 2)
IN
T
IR
U
O
D
E
T
W
U
O
E
T
I
N
O
M
B
R
S
E
U
R
2
5
1
U
M
B
L
T
IO
D
T
U
O
<
U
C
P
T
B
D
A
U
O
G
U
>
R
A
B
G
IO
R
IN
N
I
IO
D
I
N
U
2
A
B
G
R
O
E
D
V
I
D
V
D
/H
C
IN
N
O
Y
S
E
Temperature monitor (TEMP) indicator
ID
V
B
-
/P
1
S
-Y
/B
IN
B
B
T
U
G
O
/Y
R
G
R
/P
-D
I
V
-Y
/R
D
STAND BY (R) LAMP1 LAMP2
ON (G)
TEMP
(Rear view of projector)
Indicator
Display
Condition
Check
Measures
The inside is at an
abnormally high
temperature, or there
are sudden
Red lamp
flasing
(lamp unit lit)
(PT-L6510E)
• Is something
blocking the vent?
• Remove the object blocking the
vent.
• Has the projector
been operating in a
hot location?
•
Use the projector only in an
temperature changes.
environment having a temperature of
0 °C to 40 °C and humidity of 20% to
80% (with no condensation).
The ambient
temperature or internal
temperature is high.
Temperature
monitor
Red lamp lit
(lamp unit lit)
• Is the air filter
clogged?
• Turn the power off by following the
steps on page 23 and clean the air
filter. (See page 41)
The lamp unit
Red lamp
flashing
(lamp unit
not lit)
automatically shuts off
(switches to standby
state) due to abnormally
high ambient
TEMP
temperature or internal
temperature.
The lamp unit has
automatically turned
off (standby mode)
because of a high
temperature or
Red lamp lit
(Lamp unit
not lit)
(PT-L6600E)
sudden rise in
internal temperature.
Lights when lamp runtime exceeds
1800 hours. Have your dealer
replace the lamp unit.
Is replace lamp
It is time to replace
the lamp unit.
displayed on the
screen when the
power is turned on?
Red lamp lit
Lamp monitor
Are you turning the
power back on
Wait until the light source lamp cools
off before turning the power back on.
immediately after it has
been turned off?
Detected the Lamp
curcuit abnormal
condition.
Red lamp
flashing
LAMP1
LAMP2
There is a
Turn the power off by following the
steps on page 23 and consult your
dealer.
malfunction in the
lamp circuit
Caution
• To solve any problems that the TEMP and LAMP monitor show, first turn the power off by following the steps
on page 23.
• If the main power turns off after the TEMP monitor flashes, the projector has malfunctioned. Please consult
your dealer.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and replacing the air filter
If too much dust accumulates in the air filter, the temperature inside main unit will become high.
• With the PT-L6510E, the temperature sensor (TEMP) lamp will flash.
• With the PT-L6600E, the temperature sensor (TEMP) lamp will flash and the light source lamp will go out.
Clean the air filter approximately every 100 hours of use, although more frequent cleaning may be necessary
depending on the environment.
Cleaning method
1. Turn the Main Power off and remove the power plug.
Turn the power off by following the steps on page 23, and remove the power plug.
2. Remove the air filter cover.
Remove the air filter cover by pushing down on the
tab and pulling forward.
T
U
O
IN
IN
L
IA
R
E
S
IN
T
U
O
W
D
E
IR
T
U
E
T
O
I
N
O
B
M
S
E
U
R
2
15
U
L
BM
T
IO
D
T
<
T
B
AU
U
PC
U
O
>
O
G
R
A
B
G
IO
D
R
U
IN
N
R
I
IO
D
I
N
U
2
A
B
G
R
O
E
D
V
I
D
V
D
/H
I
N
C
N
O
Y
S
E
ID
-
V
/PB
1
S
-Y
/B
IN
B
B
T
U
G
O
/Y
R
G
/PR
-D
-Y
/R
VI
R
D
IN
T
U
O
N
I
L
IA
R
E
S
N
I
T
U
O
N
I
O
B
R
M
S
E
U
R
L
O
I
D
T
<
U
T
U
O
C
P
B
D
A
U
G
U
>
O
R
A
B
G
O
I
R
N
I
IN
O
I
D
IN
U
2
A
B
G
R
O
E
D
V
ID
V
D
H
/
C
IN
N
Y
O
E
S
ID
V
-
PB
/
S
Y
-
B
/
B
Y
/
R
N
I
3. Clean the air filter.
Remove accumulated dust using a vacuum cleaner.
Notch
Caution
• Be careful not to suck the air filter into the
vacuum cleaner.
Air filter
4. Attach the air filter and cover.
Place an air filter inside the air filter cover, and replace the cover by reversing the step described in (2).
Caution
• Place the air filter aligning the notch toward the upper right direction.
• Do not operate the projector without the air filter.
If the projector is operated without the air filter, dust will enter the unit and may cause a malfunction.
Note
• If dust cannot be removed with a vacuum cleaner, it is time to replace the filter. Please consult your dealer.
Replace the air filter when replacing the lamp unit.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp unit
Caution!
Replacement of the lamp unit should
only be carried out by a qualified
technician.
Caution!
Replace the lamp unit only after it has
completely cooled off.
Notes when replacing the lamp unit:
• The internal pressure of the light source is high, therefore if it is struck by hard objects or dropped, it may cause
damage. Be careful when handling.
• Handle the old lamp unit with care as it is easily broken.
• A Philips screwdriver is necessary when replacing the lamp unit. Be careful not to slip when using the screwdriver.
Caution
• The lamp unit is sold separately. Please consult the service/parts centre at your dealer.
Model No.
PT-L6510E
PT-L6600E
Lamp unit model No.
ET-LAL6510 (1 lamp) • ET-LAL6510W (2 lamps)
• Lamps other than those indicated above must not be used with this projector. Be sure to use the specified
lamp.
Lamp replacement period
The light source lamp of this projector has a life cycle of 2000 hours (Lamp power---hi, Lamp selection---dual
setting). However, this duration may be reduced depending on the usage of the projector-the frequency in which
the light is turned on and of its intervals affect the life of the lamp. Therefore it is recommended that a spare lamp
be made available before 2000 hours have elapsed. If the lamp unit is not replaced after 1800 hours, the power will
automatically shut off after 2000 hours and enter standby mode. If the power is turned on after 2000 hours, it will
turn off automatically after approximately 10 minutes and enter standby mode.
Note
• 2,000 hours is a guideline for replacement, not a guarantee time.
• Display after 1800 hours
The lamp monitor indicators (LAMP 1 or LAMP2)
S-VIDEO
AUTO
REPLACE LAMP
will light after the lamp unit runtime has elapsed
1800 hours even during standby mode.
An on-screen message indicating lamp
replacement is necessary will be displayed on the
screen 30 seconds.
(This on-screen message will disappear after 30
seconds or the projector operation buttons remote
control buttons are operated.)
This on-screen message does not disappear,
unless a “MENU” buttons or sound adjustment
“(VOLUME +/-)” buttons will be pushed, if it
reaches in 2000 hours.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp unit replacement steps
Caution
• After 2000 hours of operating the same lamp, it is only possible to operate the unit for approximately 10
minutes. Replace the lamp and steps 8 to 14 must be completed within 10 minutes:
1. Turn the power off by following the steps on page 23, remove the power plug and
confirm that the surroundings of the lamp unit have cooled off.
2. Using a Philips screwdriver, remove the
Fixing screws
4 screws on the lamp unit cover located
on the rear of the projector.
3. Remove the lamp unit cover by pulling it
forward.
Caution
Lamp unit cover
Tab
• Be careful not to break the tab located in the
centre of the lower side of the lamp unit cover.
4. Use a Phillips screwdriver to loosen the
two lamp unit fixing screws until the
screws turn freely. Then hold the handle
of the lamp unit and gently pull it out from
the projector.
Lamp unit 1
Lamp unit 2
Handle
Caution
The lamp unit will be hot after it has been
used.
Lamp unit 1
Fixing screws
Lamp unit 2
Fixing screws
You might get burned if you touch it while it is still hot.
5. Install the new lamp unit.
6.Use a Phillips screwdriver to securely tighten the 2 lamp unit fixing screws.
7. Install the lamp unit cover, and then use
Fixing screws
a Phillips screwdriver to securely tighten
the lamp unit cover fixing 4 screws.
Caution
• Firmly install the lamp unit and lamp unit cover.
If not installed firmly, a protection circuit will
Lamp unit cover
Tab
function and the power will not be turned on.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp unit
8. Insert the power cord plug into the wall outlet and then press the MAIN POWER switch.
Caution
• If the power does not turn on even after turning the MAIN POWER switch “I”, turn the MAIN POWER “O”,
confirm that the lamp unit and door are installed correctly, and turn on again.
9. Press the “POWER” button so that a picture is projected onto the screen.
10. Press the “MENU” button to display the
MAIN MENU screen, and then press the
and buttons to move the cursor to
select “OPTION2”.
MENU
INDEX WINDOW
PICTURE
POSITION
AUDIO
ZOOM/FOCUS
LANGUAGE
OPTION
OPTION
SELECT
1
2
ENTER
11. Press the “ENTER” button to display the
OPTION
2
LAMP POWER
LAMP SELECT
LAMP RUNTIME
HIGH
DUAL
1820
“OPTION2” screen, and then use the
and
buttons to select “LAMP
1
H
FUNCTION
SET ID
1
MUTE
ALL
RUNTIME”.
USER MODE
SELECT
ADJ
ESC
12. Press and hold the “ENTER” button on
the projector or the remote control for
approximately 3 seconds.
OPTION
2
[
The “LAMP RUNTIME” will change to “L1 RESET
[POWER OFF]” or “L2 RESET [POWER OFF]”.
LAMP POWER
LAMP SELECT
L1 RESET
HIGH
DUAL
POWER OFF
]
FUNCTION
SET ID
1
MUTE
ALL
Note
USER MODE
• If the “MENU” button is pressed, the lamp time
resetting screen will be cancelled.
13. Press the and buttons to select for replacement lamp setting.
L1 RESET: Replace the LAMP1
L2 RESET: Replace the LAMP2
L1+L2 RESET: Replace the LAMP1 & LAMP2
14. Press the POWER button to turn off the power.
This will reset the cumulative usage time for the lamp unit to zero.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Before asking for service
---Before asking for service, cheque the following points.
Symptoms
Cheques
• Is the power cord plug correctly plugged in?
• Is the MAIN POWER turned on?
• Is electricity running to the power outlet?
• Is the temperature monitor (TEMP) indicator on the front of the unit flashing or
turned on? (See page 40)
Power does
not turn on
• Is the lamp monitor (LAMP) indicator on the front of the unit flashing or turned on?
(See page 40)
• Is the lamp unit door installed correctly?
• A wrong ID is set. (See pages 15 and 36)
• Is the lens cap still on the lens?
• Is the image input correctly connected?
• Is the input mode set correctly? (See page 23)
• Is the black level adjustment set at the minimum level? (See page 30)
• Is the equipment connected to the projector operating correctly?
• Is the shutter function turned on? (See page 25)
No image
• Is the lens focused properly? (See page 23)
• Is the projection distance correct? (See page 18)
• Is the lens dirty?
Image is blurred
• Is the projector positioned directly in front of the screen? (See page 18)
• Is the colour density and colour tone setting correct? (See page 30)
• Is the equipment connected to the projector correctly adjusted?
Light colour/
bad colour tone
• Is the sound input correctly connected?
• Is the volume set to the minimum level? (See page 23 and 27)
• Is the shutter or mute turned on? (See page 25 and 35)
• Is the cable connected to the AUDIO OUT terminal?
No sound
• Are the batteries exhausted?
• Are the battery polarities set correctly? (See page 14)
• Are their any obstacles between the remote control and the remote control sensor?
(See page 14)
Remote control
does not operate
•
Are you trying to operate the remote control beyond its operable range? (See page 14)
• Are you controlling from external equipment using the REMOTE terminal? (See
page 39)
• Is their any external light interfering with remote control operation?
• A wrong ID is set. (See pages 15 and 36)
• Is the input mode properly set? (See page 23)
• Is the correct signal system (TV system) selected? (See page 31)
• Are their any malfunctions on the source side, such as bad video tapes?
• Are you inputting a signal that is not compatible with this projector? (See page 48)
Abnormal image
• Is the cable too long?
Does not display
images from PCs
• Is the video output signal setting of the notebook computer correctly set?
Setting :
key (Read the operating instructions of the your PC.)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
PT-L6510E (XGA)
PT-L6600E (SXGA)
ModelNo.
Supplyvoltage
Power consumption
220 V - 240 V AC, 50/60 Hz
600 W (approx. 9 W in Standby mode with fan inactive)
1.3 inch diagonal (aspect ratio: 4:3)
with microlens array
Panel size
Display system
Driving scheme
3 transmissive LCD panels (3 primary colors)
Active matrix
1.398.784 pixels (1.366 x 1.024 dots) x 3
Pixel count
786.432 pixels (1.024 x 768 dots) x 3
Powered zoom
1 to 1.3
powered focus control
F = 1.7 to 2.3, f = 49.1 to 63.8
2 UHM lamps with 220 W rating each
Projection lamp
Optical output
Composite/S-Video
4 200 lm (ANSI)
H = 15.74/15.63 kHz, V = 50/60 Hz
3 600 lm (ANSI)
H = 24 to 97 kHz, V = 50 to 120 Hz, PIAS (Panasonic Intelligent Auto Scanning) format
Dot clock frequency: under 132 MHz Dot clock frequency: under 162 MHz
RGB signal
DVI-D signal
VGA60, S-VGA60, XGA60, S-XGA60
[625i]
H = 15.63 kHz
V = 50 Hz
[480i]
H = 15.75 kHz
H = 31.5 kHz
H = 33.75 kHz
V = 60 Hz
60 Hz
[720p]
[1080i]
H = 45 kHz
60 Hz
V =
YPBPR
signal
[480p]
[1035i]
V =
V = 60 Hz
H = 33.75 kHz
V = 60 Hz
YPB
P
R
signal
480i, 480p, PAL (625i), 720p, 1 035i, 1080i
6 standards (NTSC, NTSC4.43, PAL, PAL-M, PAL-N, SECAM)
30 to 300 inches diagonal
Compatible TV standards
Screen size
Projection distance
Optical axis shift span
Aspect ratio
1.4 to 13.2 meters
10:10 to 1:19
4:3 (SXGA 5:4)
Projection scheme
Speaker
Menu-selectable from front, rear, ceiling mount, and floor standing
2 oval speakers (4 x 7 cm)
Max. audio output power
DVI-D input/output
6 W (3 W + 3 W) (stereo)
1 set DVI-D 24pin
1 set BNC x 5
[YPB input] Y:1.0 V [p-p] including sync. signal PB
[RGB input]
PR
PR: 0.7 V [p-p] 75 Ω
0.7 V [p-p] 75 Ω
G-Sync.:
RGB1 (x1)
input
1.0 V [p-p] 75 Ω
HD/SYNC:
VD:
TTL-compatible, high-impedance w/ auto active Hi/Lo switching
TTL-compatible, high-impedance w/ auto active Hi/Lo switching
46
Download from Www.Somanuals.com. All Manuals Search And Download.
High-density D-sub 15-pin connector (female)
YPB input: Y = 1.0 V [p-p] including sync. signal PB
P
R
P
R
= 0.7 V [p-p] 75 Ω
RGB input:
G-Sync.:
0.7 V [p-p] 75 Ω
RGB2 input
1.0 V [p-p] 75 Ω
HD/SYNC: TTL-compatible, high-impedance w/ auto active Hi/Lo switching
VD: TTL-compatible, high-impedance w/ auto active Hi/Lo switching
1 set stereo minijack,
Audio input
for RGB 1/2
0.5 V [rms]
BNC x 1
VIDEO
1.0 V [p-p] 75 Ω
4-pin mini-Din x 1
S-video
Y = 1.0 V [p-p] C = 0.286 V [p-p] 75 Ω
RCA jack x 2 (L/R),
Audio input for
0.5 V [rms]
composite/S-video
1 set stereo minijack, (monitor output, stereo-compatible),
0 V [rms] to 2.0 V [rms] (variable)
High-density D-sub 15-pin connector (female) x 1
Audio output
YPB
RGB output: 0.7 V [p-p] 75 Ω
G-Sync.: 1.0 V [p-p] 75 Ω
P
R
output:
Y = 1.0 V [p-p] including sync. signal PB
P
R
= 0.7 V [p-p] 75 Ω
RGB output
HD: TTL-compatible, high impedance
VD: TTL-compatible, high impedance
9-pin D-sub connector (female) Use the RS-232C serial port
For PC Control
SERIAL
REMOTE
9-pin D-sub connector (female)
For wired mode
M3 jack 1 set
WIRED input
USB input
USB output
Wired remote control, For daisy-chain control
4-pin square connector Type B
For wired mouse
Type A
For daisy-chain control, Max. 5 V/0.5 A
Power cord
Enclosure
2.5 metres
Resin mold part
Outer dimensions
Weight
Width: 495mm Height: 179 mm Depth: 495 mm
13.8 kg
Operating temperature range: 0 °C to 40 °C
Operating humidity range: 20 % to 80 % (with no condensation)
Operating conditions
Power supply
Control range
Weight
3 V DC (2 type-AAA dry batteries)
Approx. 7 m (in front of light receiver)
108 g (with batteries)
Outer dimensions
(W) : 33 mm
(H) : 40 mm
(D) : 168 mm
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
<Compatible RGB Signals>
The following table specifies the types of RGB signals compatible with the projector.
If signals other than this are applied, the projector may produce anything from a distorted display to simply the
default (blue or black) background.
Compatible Signal
Resolution
H x V Pixels
H. Scanning Frequency (kHz)
V. Scanning Frequency (Hz)
640
640
640
640
640
640
640
800
800
800
800
800
800
1 024
1 024
1 024
1 024
1 024
1 024
1 024
1 024
1 152
1 152
1 152
1 120
1 120
1 280
1 280
1 280
1 280
1 280
1 280
1 280
1 280
1 600
1 600
1 600
832
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
400
400
480
480
480
480
480
600
600
600
600
600
600
768
768
768
768
768
768i
768
768
864
864
864
750
750i
1 024
1 024
1 024
1 024
1 024
1 024*
1 024i
1 024i
1 200
1 200
1 200
624
870
1 035i
720
480i
576i
483
24.8
31.5
31.5
35.0
37.9
37.5
43.3
32.1
35.2
37.9
48.1
46.9
53.7
48.4
56.5
60.0
65.5
68.7
35.5
80.7
94.0
63.9
67.5
77.1
50.1
32.6
52.4
64.0
72.4
78.2
80.0
91.2
46.2
47.6
75.0
87.5
93.8
49.7
68.6
33.8
45.0
15.7
15.6
31.5
56.4
70.1
59.9
66.7
72.8
75.0
85.0
51.0
56.3
60.3
72.1
75.0
85.1
60.0
70.1
75.0
81.6
85.0
86.8
100.8
120.0
70.0
75.0
85.0
60.1
80.0
50.0
60.0
66.3
71.7
75.0
85.0
86.0
88.9
60.0
70.0
75.0
74.6
75.0
60.0
60.0
59.9
50.0
59.9
VGA400
VGA480
SVGA
XGA
MXGA
SXGA
UXGA
MAC16
MAC21
HDTV
720p
NTSC
PAL
1 152
1 920
1 280
768
768
720
480p
* PT-L6600E ONLY
Note
• The PT-L6600E has a pixel resolution of 1 366 x 1 024. Pixel data exceeding this resolution is converted into
1 366 x 1 024 pixels.
• The PT-L6510E has a pixel resolution of 1 024 x 768. Pixel data exceeding this resolution is converted into
1 024 x 768 pixels.
• Suffix "i" denotes interlaced scanning.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
unit : mm
IN
IN
OUT
L
R
IN
OUT
IN
OUT
RGB
AUDIO
IN
S-VIDEO IN
VIDEO
AUDIO IN
AUDIO
USB
SERIAL
R/R-Y/PR
G/Y
B/B-Y/PB SYNC/HD
VD
OUT
RGB
1
IN
RGB
2
IN
RGB OUT
REMOTE
WIRED
IN
OUT
DVI-D
>
PC
<
TBMU152
476
495
Trademark acknowledgments
Trademark
• PS/2, VGA, and XGA are trademarks of U.S. IBM Corporation.
• Macintosh is a registered trademark of U.S. Apple Computers, Inc.
• PC-98 is a trademark of NEC Corporation.
• S-VGA is a trademark or registered trademark of the Video Electronics Standards Association.
• Windows is a registered trademark of Microsoft Corporation.
The rights of trademarks or registered trademarks not specified are recognised.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
M1002-0
Matsushita Electric Industrial Co., Ltd
© Matsushita Electric Industrial Co., Ltd. 2002
Download from Www.Somanuals.com. All Manuals Search And Download.
|