Elite-7m
Operation manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
The user is cautioned that any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that of the receiver
Consult the dealer or an experienced technician for help
WARNING: When a GPS unit is used in a vehicle, the vehicle operator is solely responsible for
operating the vehicle in a safe manner. Vehicle operators must maintain full surveillance of all
pertinent driving and boating conditions at all times. An accident or collision resulting in damage
to property, personal injury or death could occur if the operator of a GPS-equipped vehicle fails to
pay full attention to travel conditions and vehicle operation while the vehicle is in motion.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Entering text ............................................7
Cursor......................................................7
Goto cursor..............................................8
Advanced Mode ......................................8
Standby mode .........................................8
Restore defaults ......................................8
Pages................................................ 9
Steer Page...............................................9
Chart Page ..............................................9
Overlay Data..........................................10
Introduction...................................... 3
Unit Controls............................................3
Inserting microSD cards ..........................4
Basic Operation............................... 5
Setup wizard............................................5
Pages ......................................................5
Page menus ............................................5
Accessing the Settings menu..................6
Accessing menu items.............................6
Working with menus ................................6
Dialogs.....................................................7
Table of Contents | Elite-7m
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarms ..................................................26
Saving Screenshots...............................26
Specifications ................................ 29
Index............................................... 30
Chart Operation ............................. 12
Chart Menu............................................12
Waypoints, Routes, Trails......................13
Routes Screen.......................................14
Trails Screen .........................................18
Orientation.............................................20
Chart Settings........................................21
Navigation Settings ..................................22
Settings .......................................... 24
Settings menu........................................24
System...................................................24
Table of Contents | Elite-7m
2
Download from Www.Somanuals.com. All Manuals Search And Download.
unit Controls
Getting Started
LiGhT/Power: controls backlight
level and turns unit on/off
To turn on/off the unit, press and
hold the LiGhT/Power key for
three seconds.
Turn unit
on/off
KeYPAD: controls cursor & selects
items on menus
Press the zooM in and zooM
ouT keys at the same time to set
a Man Overboard waypoint. Your
system will automatically create
an active route back to the MOB
waypoint. You must cancel navi-
gation to terminate the function.
PAGeS: allows you to select a page to
view
Man
overboard
waypoint
Menu: opens settings, context and
page menus
enTer: finalizes menu selections;
save waypoint at cursor position
Adjusting This unit has 10 backlight levels.
the Press the LiGhT/Power key to
backlight switch backlight levels.
MoB: press and hold both Zoom keys
to create a Man Overboard waypoint
zooM Keys: used to zoom in/zoom
Muting
Audio
Select Mute Audio from the
System menu and press enTer.
out
microSD slot: insert a blank microSD card to
save screen captures; or insert a microSD map-
ping card to use mapping data (See illustration
on page 2)
Select GPS from the System settings
menu. Highlight GPS source and
press enTer. Select the desired
source.
Selecting a
GPS
Source
Introduction | Elite-7m
3
Download from Www.Somanuals.com. All Manuals Search And Download.
inserting microSD cards
Carefully slide the microSD card into the slot until it clicks into place.
To remove, carefully push in the card until it clicks out of place.
Introduction | Elite-7m
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Page menus
Basic Operation
The Steer and Chart pages have menus that can
only be accessed when those pages are displayed.
Setup wizard
The Setup wizard will appear when the unit is
turned on for the first time. To choose your own
settings, do not run the setup wizard. To restart the
Setup wizard, restore defaults.
Chart menu
Chart page
Pages
This unit has two pages: Steer and Chart. Press the
pages key to switch pages.
Steer menu
Steer page
Basic Operation | Elite-7m
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing the Settings menu
Working with menus
There are several menu types used to make
adjustments to options and settings, including
scrollbars, on/off features and dropdown menus.
Scrollbars
Select the scrollbar and press the
keypad left (decrease) or right
(increase).
Accessing menu items
The keypad and enter key are used to select
menu items and open submenus. Use the keypad
to highlight the desired item and press enter.
On/Off features
Select the on/off item and
press enter to turn it on/
off.
Basic Operation | Elite-7m
6
Download from Www.Somanuals.com. All Manuals Search And Download.
To input text:
1. Use the keypad to select the desired
Dropdown menus
Select the dropdown menu
and press the keypad up/
down to select the desired
item. Press enter.
character and press enter.
2. Repeat Step 1 for each character.
3. When entry is completed, highlight OK
and press enter.
nOte: Press the Menu key to Exit
menus.
Switches letters
to uppercase/
lowercase
Dialogs
Switches keyboard
between Alpha and
QWERTY layout
Dialogs are used for user input
or for presenting information to
the user. Depending on the type
of information or entry, different
methods are used to confirm,
cancel or close the dialog.
Cursor
The keypad moves the cursor around the display,
allowing you to scroll the map, select map items
and review sonar history.
entering text
Press Menu and select Return to vessel or Exit cur-
sor mode to clear the cursor.
Some functions, like naming a waypoint, route or
trail, will require you to input text.
Basic Operation | Elite-7m
7
Download from Www.Somanuals.com. All Manuals Search And Download.
goto cursor
Standby mode
Lowers power consumption by turning off sonar
and the display.
Used to navigate to the cursor.
1. Move the cursor to a desired location
Press the PWr/Light key to
and press Menu.
access the Backlight dialog.
2. Select Goto cursor and press enter.
Select Standby and press enter.
Press any key to resume normal
operation.
Advanced Mode
Enables advanced features and settings.
nOte: Leaving your unit in Standby
mode when your boat is not is use will run
down your battery.
The following features are enabled when Advanced
mode is turned on:
•
Navigation (Enables arrival radius, off-
course distance and Bearings setting)
•
Alarms (Enables arrival, off course and
anchor alarm options)
restore defaults
Resets unit options and settings to defaults.
•
•
NMEA 0183 Output
Units (Enables distance, speed, depth,
temperature, and bearings options)
Basic Operation | Elite-7m
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Current location
Pages
Depth contours
Direction to cursor
Compass
Current Track
Zoom
Range
Current location;
distance to cursor
Waypoint
Navigation
information
Your location
Chart Page
Steer Page
Consists of map that moves in real-time as you
move. By default, the map is shown from a birds-
eye view with North at the top of the screen.
The Steer page has a compass that shows your
current track, the direction to your destination, and
a digital data navigation panel.
Pages | Elite-7m
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Overlay Data
Used to select data shown on the Chart page.
To add overlay data:
1. From the Chart page, press Menu.
2. Select Overlay data and press enter.
3. Select Configure and press enter.
Overlay data
Show
4. Press Menu and select Add. Press
enter.
Enables/disables the display of overlay data,
allowing you to remove overlay data from the
screen without deleting the current overlay data
configuration.
5. Select a data category and press
enter.
6. Select the desired data and press
enter.
7. Press Menu and select Return to
Overlays. Press enter.
8. Press Menu, select Done Configuring
Configure
and press enter.
Allows you to select/customize overlay data.
Pages | Elite-7m
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing Overlay Data
You can select a data source, add/remove data and
adjust the size and position of overlay data on the
screen.
Select the desired overlay
data from the Configure Item
Locations and Sizes dialog and
press Menu. The configuration
menu will appear.
To select a data source:
1. Select Data sources and press enter.
2. Select the data type and press the
keypad to the right.
3. Highlight the desired data source and
Data sources
press enter.
Used to select the network device that will supply
source data for a selected data type.
Pages | Elite-7m
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Chart Operation
Chart menu
Chart Menu
New Waypoint
Press Menu from any Chart pages to open the
Chart menu.
Creates a waypoint at your current location or
at the cursor position. When the cursor is on the
screen, waypoints will be saved at the cursor
position; conversely, if the cursor is not displayed
onscreen, waypoints will be saved at your current
position.
Chart Operation | Elite-7m
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Waypoints, Routes, Trails
Used to create, edit, navigate and delete way-
points, routes and trails.
Press the keypad left/right to toggle between
waypoint, routes and trails tabs.
Waypoints
menu
Waypoints Screen
Waypoints
menu
Edit
Allows you to edit the name,
icon and latitude/longitude.
of a selected waypoint.
Chart Operation | Elite-7m
13
Download from Www.Somanuals.com. All Manuals Search And Download.
New
Sort
Controls how the waypoints list will be
sorted — by name or by nearest.
Creates a new waypoint
at the cursor or vessel
position. You can also select
waypoint name, icon and
latitude/longitude from the
new waypoint menu.
Routes Screen
Used to create, edit, navigate and delete routes.
Use the keypad to highlight the Routes tab to ac-
cess the Routes screen.
Show
Displays the selected waypoint
on the map.
Goto
Routes screen
Routes
menu
Allows you to navigate to a waypoint.
Creating a route
Delete and Delete All
Routes can be created by inserting waypoints from
the waypoints list or by using the cursor to posi-
tion new points on the chart. You also can add way-
points to a route by selecting them from the chart
screen.
Delete is used to delete a
selected waypoint. Delete
All deletes all waypoints.
Chart Operation | Elite-7m
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserts waypoint between
existing route waypoints
Leg Name field
Adds waypoint to
end of the route
5. Highlight Waypoint from list and press
enTeR.
Route waypoint
menu
Starts navigation
to the selected
route waypoint
6. Select the desired waypoint and press
enTeR.
7. Press Menu and select Add to end to
To create a route from waypoint list:
1. Press Menu from the Routes screen.
2. Select New... and press enTeR.
add another waypoint to the route.
8. When the route is complete, press
Menu, select Stop Editing and press
enTeR.
3. Press the keypad down to select the
Leg Name field and press enTeR.
9. Select Save and press enTeR.
4. Press Menu, select Add to End and
press enTeR.
Chart Operation | Elite-7m
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a route using points from chart:
2. Select Start and press enTeR.
1. Repeat Steps 1-4 from the instructions
for Creating a route from waypoint list.
3. Select Forward or Reverse and press
enTeR.
4. Press Menu and select Return to Chart.
2. Select Points from chart and press
Press enTeR.
enTeR. The chart page will appear.
3. Move the cursor to the desired location.
Press enTeR to set a waypoint.
4. Repeat Step 3 to add more route
waypoints.
5. Press Menu and select Stop adding.
Press enTeR.
6. Highlight the Save button and press
enTeR.
Navigating a route
Routes can be navigated in forward
or reverse.
Routes menu
1. Select the desired route
on the Route screen and
press Menu.
Chart Operation | Elite-7m
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To cancel navigation:
To access the Edit or New Route menu, select Edit
or New on the Routes menu and press enTeR.
1. Press Menu from the chart screen.
2. Select Navigation and press enTeR.
3. Highlight Cancel and press enTeR.
4. Select Yes and press enTeR.
To finalize changes on the Edit or New Route
menus, highlight the Accept button and press
enTeR.
Displayed
Edit and New Route menus
Used to show/hide a route on the display, which
prevents the screen from being cluttered by too
many routes
Used to edit/create routes, route names and to turn
on/off the route display.
Turns on/off route
display on map
Delete and Delete All
To edit/create a route, use
the keypad to select the Leg
Name field and press Enter.
Delete is used to delete
individual routes. Delete
All, removes all routes.
Chart Operation | Elite-7m
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Trails Screen
Used to create, edit, navigate and delete trails. Use
the keypad to highlight the Trails tab to access the
Trails screen.
Trails menu
Trails screen
Trails menu
Creating trails
When creating a trail you can customize the trail
name and color from the New Trail.
To create a trail:
1. Select New and press enTeR. The
New Trail dialog will appear.
2. Select Save and press enTeR.
Chart Operation | Elite-7m
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit and New Trail menus
Navigating a trail
Allows you to edit/create trails, select trails names,
trail color, trail display and the trail being recorded.
You can also convert a trail into a route from the
Edit Trail menu.
A trail must be saved as a route before it can be
navigated.
To save a trail as a route:
1. Highlight the desired trail on the Trails
screen and press enTeR. The Edit
Trail menu will appear.
2. Highlight Create Route and press
enTeR. The Edit Route menu will
appear.
3. Highlight Done and press enTeR.
Turns on/
off trail
recording
Turns on/
off trail
display
on map
4. For navigation instructions refer to the
Navigating a route segment.
Edit Trails menu
Displayed and Record
Displayed allows you to show/hide trails on the
map display, preventing the screen from being
cluttered with trails.
Chart Operation | Elite-7m
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Overlay Data
The Record command allows you to record or
resume recording a desired trail.
Allows you to select data (course over ground, etc)
to be displayed on top of the Chart page.
Delete and Delete All
Delete is used to remove
individual trails. Delete
All removes all trails.
Overlay data
Orientation
Overlay data setup is covered in the Pages section.
Allows you to select North Up or Course Over
Ground (COG) as the map orientation.
Settings
Accesses the Chart settings menu.
Chart Operation | Elite-7m
20
Download from Www.Somanuals.com. All Manuals Search And Download.
COG Extension
Chart Settings
A line extending from the front of
the current position icon that esti-
mates the time and distance to ar-
eas in front of you.
Controls map data used on the chart screen as well
as display settings like grid lines, waypoints, routes
and trails.
Grid Lines
Displays base values for
latitude and longitude, making
it easier to get a general idea of
your location on the latitude/
longitude scale.
Chart Settings menu
Chart Data
Selects map data that will be used on the Chart
display (Lowrance or Navionics regional map). Go
to Navionics.com to see a full selection of available
charts.
Chart Operation | Elite-7m
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Waypoints, Routes and Trail displays
navigation Settings
(Advanced mode only)
From the Chart Settings menu, you can turn on/
off waypoint, route and trail display properties. Controls Arrival Radius and Off Course distance
Turning off display properties allows you to get settings and is used to turn on/off WAAS/MSAS/
a better view of the map, if the screen becomes EGNOS.
cluttered with waypoints, routes and/or trails.
Waypoints, Routes, Trails
Accesses the Waypoints, Routes & Trails screen.
Waypoints, Routes and Trails are covered in the
Chart section.
Navigation Settings menu
Chart Operation | Elite-7m
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrival Radius
Magnetic Variation
Sets the arrival radius threshold for the Arrival Controls whether magnetic variation will be calcu-
alarm. The arrival alarm will sound when your ves- lated using Automatic or Manual settings. Magnet-
sel comes within a selected distance (arrival radius) ic variation is the angle between magnetic north
of the destination waypoint.
and true north. The automatic setting reconciles
the variation for you.
Off Course Distance
WARNING: You should only use the
Manual magnetic variation setting if
you have variation information from a
verified source.
Sets Off Course Distance threshold for the Off
Course alarm. When the selected off course dis-
tance is exceeded, the Off Course alarm will sound
when the alarm is enabled.
Bearings
Controls whether bearing will be calculated using
True North or Magnetic North. Magnetic North
should be used when navigating with a compass
course or heading; otherwise use the default set-
ting, True North.
Chart Operation | Elite-7m
23
Download from Www.Somanuals.com. All Manuals Search And Download.
System
Settings
Adjusts unit settings like language, mute audio
and advanced mode.
Settings menu
Accesses installation and configuration settings for
your unit.
Enables
advanced
features and
settings
(Advanced mode
Settings
menu
System menu
only)
Displays software
information
(Advanced mode
only)
Settings | Elite-7m
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Language
Trip Calculator
Tracks trip time, speed
and distance when you
are moving faster than the
selected threshold.
Selects the language used on
menus and text boxes.
Audio
Adjusts volume and turns on/off unit audio, like
key beeps, alarm sounds, etc.
Advanced Mode
Enables features and settings only available with
unit in Advanced Mode.
Time
Used to set local time, and time
and date formats for your unit.
Restore Defaults
Switches the unit back to default settings.
GPS
Monitors the location of
satellites in view and the
quality of the unit’s satellite
lock-on.
Browse Files
Allows you to view a list of the files saved to the
microSD card.
Settings | Elite-7m
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving Screenshots
Alarms
You can save screenshots to a microSD card by
inserting a microSD card into the card slot and
pressing Power and then Zoom (+).
Enables alarms and selects alarm thresholds.
Arrival, Off Course and Anchor alarms are only
available in Advanced mode.
You must view files on a computer or other microSD
compatible device.
NOTE: You cannot save screenshots to
a Navionics card or other mapping cards.
Alarms
menu
About
Displays software information about this unit.
Before attempting a software update, you can
check the version of software your unit is using by
accessing the About screen.
Lowrance periodically updates unit software to
add features and improve functionality. To see
the latest available software version go to www.
lowrance.com.
Settings | Elite-7m
26
Download from Www.Somanuals.com. All Manuals Search And Download.
NMEA 0183 Output
Alarms
You can select the NMEA 0183 sentences the unit
will use when connected to a VHF radio or other
NMEA 0183 device.
sounds alarm when you are within a selected
distance of your destination (Advanced
Mode only)
Arrival
sounds alarm when course exceeds
a
Off
Course
You can also adjust the Baud rate, but the default
setting works best under most conditions.
selected off-course threshold (Advanced
Mode only)
sounds alarm when vessel moves a selected
distance (Advanced Mode only)
Anchor
Units
Allows you to select the unit of measure used by
the unit. Unit options vary depending on whether
the unit is in basic or advanced mode.
NMEA 2000
With the unit connected to a NMEA 2000 network,
you can select a GPS antenna on the network as
your GPS source, and share newly created way-
points with other display units on the network.
Basic Mode
Advanced Mode
Settings | Elite-7m
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Simulator
You will not be able to share existing waypoints.
Only waypoints created while the unit is connect-
ed to a NMEA 2000 network can be shared, and
only with units on that network.
Simulates GPS and/or sonar activity. Simulations
can be customized on the Simulator options menu.
Selecting a GPS source
Data sources
Allows you to select the source this unit will use for
GPS data.
Device list
Used to view data for devices connected to your
NMEA 2000 network.
Settings | Elite-7m
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Elite 7m
General
GPS
Mapping card
slot
microSD and microSDHC
5.3”H (234mm) x 9.2”W (136mm); 5.9”
H (151mm) with bracket
Case Size
Display
16 parallel channel (internal); optional
external GPS antenna sold separately
GPS Antenna
(7”diagonal) 16-bit color Full VGA Solar
MAX™ 800x480 color TFT
Fishing Hot Spots, NauticPath
Navionics (Hotmaps, Premium and
Gold)
&
Mapping
compatibility
Waterproof stan- IPX7
dard
W a y p o i n t s , Up to 3000 waypoints, 100 routes and
Routes & Trails 100 retraceable plot trails
Backlight
LED (10 levels)
NMEA 2000
NMEA 0183 Output
Communications
Declaration of
Conformity
Part 15.103 FCC rules & CE RTTE directive
1999/5/EC
Power
Transmit Power
250W RMS
Power
Requirement
12V
Voltage Input
Current drain
Fuse type
10 to 17V
Typical: 1.1A
3-amp Automotive
Specifications | Elite-7m
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
N
Chart Page 9
GPS Source 25
GPS Status 25
Grid Lines 21
A
Navigating a route 16
Navigating a trail 19
Navigation 22
Navigation menu 22
New Waypoint 12
NMEA 0183 27
COG Extension 21
Creating a route 14
Creating trails 18
Cursor 7
About 26
Advanced Mode 8
Alarms 26
Anchor alarm 27
Arrival alarm 27
Arrival Radius 23
L
Language 25
D
NMEA 2000 27
Data sources 28
M
Data Port 25
Dialogs 7
Dropdown menus 7
B
Magnetic Variation 23
Man
Overboard
waypoint 3
Man Overboard way-
point 3
O
Bearings 23
Browse Files 25
E
Off Course alarm 27
Off Course Distance 23
On/Off features 6
Orientation 20
Editing waypoints 13
C
Cancel navigation 17
Chart 21
Chart Data 21
Chart menu 21
G
microSD cards 4
Mute Audio 25
Goto cursor 8
Goto waypoint 14
Index | Elite-7m
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby mode 8
Steer Page 9
System settings 24
Overlay Data 10, 20
Configure 10
Customizing 11
Show 10
T
P
Text entry 7
Time 25
Page menus 5
Trail display 22
Trails Screen 18
Turn unit on/off 3
R
Route display 22
Routes Screen 14
U
Unit Controls 3
Units 27
S
Saving Screenshots 26
Scrollbars 6
Setup wizard 5
Software Updates 26
Sort waypoints 14
W
Waypoint display 22
Waypoints, Routes,
Trails 13
Working with menus 6
Index | Elite-7m
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Databases Limited Warranty
Navico Databases License Agreement
“We”, “our”, or “us” refers to Navico, the manufacturer of this product. “You” or “your”
refers to the first person who purchases the product as a consumer item for personal, family, or
household use. The Databases Limited Warranty applies to the one or more databases that your
product may contain. We refer to each of these as a “Database” or together as the “Databases.”
Your product may thus include the “WBS Database” which contains worldwide background
surface mapping data, the “Indigo Database” which contains inland mapping data, or other
Databases.
We warrant to you that we have accurately compiled, processed, and reproduced the portions
of the source material on which the Databases are based. However, we are under no obliga-
tion to provide updates to the Databases, and the data contained in the Databases may be
incomplete when compared to the source material. WE MAKE NO EXPRESS OR IMPLIED
WARRANTY OF ANY KIND ABOUT THE ACCURACY OF THE SOURCE MATERIAL
ITSELF, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES
THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD
USE (“YOU”) AND NAVICO, THE MANUFACTURER OF THIS PRODUCT (“WE”,
“OUR”, OR “US”).
USING THE PRODUCT ACCOMPANIED BY THIS LICENSE AGREEMENT
CONSTITUTES ACCEPTANCE OF THESE TERMS AND CONDITIONS.
IF YOU DO NOT ACCEPT ALL TERMS AND CONDITIONS, PROMPTLY RETURN
THE PRODUCT WITHIN 30 DAYS OF PURCHASE. PLEASE RETURN USING THE
ENCLOSED UPS SHIPPING LABEL AND INCLUDE: PROOF OF PURCHASE, NAME,
ADDRESS, AND PHONE NUMBER. YOUR PURCHASE PRICE AND ANY APPLICABLE
TAXES WILL BE REFUNDED. PLEASE ALLOW 4-6 WEEKS TO PROCESS YOUR
REFUND.
1.
This License Agreement applies to the one or more databases that your product
may contain. We refer to these singly as a “Database” and together as the “Da-
tabases.” Your product may thus include the “WBS Database” which contains
worldwide background surface mapping data, the “Indigo Database” which
contains inland mapping data, or other Databases.
If there is a defect in any Database, your exclusive remedy shall be, at our option, either a
refund of the price you paid for the product containing the defective Database or a replacement
of such product. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANY-
ONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT
DAMAGE OF ANY KIND.
2.
The Databases that your product may contain are licensed, not sold. We grant
to you the nonexclusive, nonassignable right to use these Databases for supple-
mental navigation reference purposes, but only as long as you comply with
the terms and conditions of this License Agreement. We reserve the right to
terminate this license if you violate any aspect of this License Agreement. You
are responsible for using official government charts and prudent navigation for
safe travel.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the product has
been serviced or repaired by anyone other than us; (2) when the product has been connected,
installed, combined, altered, adjusted, or handled in a manner other than according to the
instructions furnished with the product; (3) when any serial number has been effaced, altered,
or removed; or (4) when any defect, problem, loss, or damage has resulted from any accident,
misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary
maintenance in accordance with the instructions of the owner’s manual for the product.
We reserve the right to make changes or improvements in our products from time to time
without incurring the obligation to install such improvements or changes on equipment or
items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights which may
vary from state to state.
Your remedies under this warranty will be available so long as you can show in a reasonable
manner that the defect occurred within one (1) year from the date of your original purchase,
and we must receive your warranty claim no later than 30 days after such 1-year period
expires. Your claim must be substantiated by a dated sales receipt or sales slip.
3.
4.
The Databases housed in your product are protected by the copyright notices
appearing on the product or its screen(s). You may NOT modify, adapt, trans-
late, reverse engineer, decompile, disassemble, rent, lease, or resell any Data-
base, and you may NOT create derivative works based upon any Database or its
contents. Any unauthorized reproduction, use, or transfer of a Database may be
a crime and may subject you to damages and attorney fees.
This License Agreement will terminate immediately without prior notice from
us if you fail to comply with or violate any of the provisions of this Agreement.
Upon termination, you will promptly return all products containing one or more
Databases to us.
5.
6.
Prices and programs are subject to change without notice.
This LicenseAgreement shall be governed by the laws of the State of Oklahoma
and comprises the complete and exclusive understanding between you and us
concerning the above subject matter.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact information
Customer Service:
1-800-628-4487
(8 a.m. to 5 p.m. Central Standard Time, M-F)
(Canada)
1-855-361-1564
(8 a.m. to 5 p.m. Eastern Standard Time, M-F)
Ordering Accessories
Visit our website
Download from Www.Somanuals.com. All Manuals Search And Download.
Visit our website:
*988-10433-001*
N2584
Download from Www.Somanuals.com. All Manuals Search And Download.
|