988-0176-01B
HDS-5 & HDS-7
Fish Finding Sonar and GPS
Operations Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Table of contents
Introduction....................................................................................... 5
Keypad.......................................................................................................7
Backlight ....................................................................................................7
Language...................................................................................................7
Menus ........................................................................................................ 8
Selecting Chart Data ................................................................................ 8
Pages............................................................................................... 11
Data Overlay............................................................................................ 12
Configuration menu ................................................................................. 16
Sonar Page.............................................................................................. 17
Radar Page.............................................................................................. 18
Utilities .....................................................................................................23
Sonar Operation.............................................................................29
Viewing Sonar History .............................................................................29
Sonar Menu .............................................................................................30
Sonar Options..........................................................................................33
Palette......................................................................................................34
Log Sonar Data........................................................................................36
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Chart menu..............................................................................................40
Search by Coordinates ............................................................................54
Find Chart item ........................................................................................54
Map Orientation .......................................................................................55
Look Ahead..............................................................................................55
Chart categories ......................................................................................56
Navionics .................................................................................................58
Radar menu ............................................................................................. 61
Radar Overlay.......................................................................................... 67
Sonar Settings Menu ............................................................................... 79
Manual Mode ...........................................................................................80
Installation Menu......................................................................................82
Keel Offset...............................................................................................82
Radar Settings Menu...............................................................................86
Fuel ..........................................................................................................93
Alarms......................................................................................................97
Trails.........................................................................................................99
Units.......................................................................................................100
Vessels...................................................................................................108
Simulator................................................................................................ 110
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Unit Care .........................................................................................114
Index............................................................................................... 123
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Blank page
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introduction
Thank you for purchasing from Lowrance, the industry leader in marine technology.
This manual is packaged with a Quick Start Guide, Installation Guide, License and
Warranty booklet and NMEA 2000 Networks Installation Instructions. If any of
these documents are missing, you may acquire them via a free download at www.
lowrance.com or by contacting customer service.
Lowrance Customer Service
12000 E Skelly Dr
Tulsa, OK 74128
(800) 324-1356
Canada (800) 661-3983 or (905) 629-1614
About this manual
This manual documents how to adjust features and options in your display unit. The
information in each section follows the same sequence as your display unit’s menus.
If you would like information on how to get the most out of your unit, visit our web
site, www.lowrance.com; click on the Support tab and select Tips and Tutorials.
Manual Conventions
When you are instructed to press a button in this manual, the button will be shown
in all caps and bold text like — MenU, exIT, enTeR, etc. If you are instructed
to select an item from a menu, the item to be selected will be listed in bold like —
Brightness, Key beeps, etc.
For example: Press MenU, select Language and press enTeR.
WARNING: When a GPS unit is used in a vehicle, the
vehicle operator is solely responsible for operating the
vehicle in a safe manner. Vehicle operators must main-
tain full surveillance of all pertinent driving, boating or
flying conditions at all times. An accident or collision re-
sulting in damage to property, personal injury or death
could occur if the operator of a GPS-equipped vehicle
fails to pay full attention to travel conditions and vehicle
operation while the vehicle is in motion.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Lowrance HDS-5 and HDS-7
ZOUT: Zoom out to see more of the map with less detail
ZIn: Zoom in to see less of the map with more detail
MOB: Pressing ZOUT and ZIN at the same time will set a man overboard waypoint
KeYPAD: move the
cursor, scroll through
menus, adjust features,
view sonar/GPS history
enTeR: finalize
menu selections;
shortcut key for
functions like saving
a waypoint at cursor
position
exIT: cancels
entries, closes
menus & windows;
toggles between
cursor position and
chart location on
Chart page
PAGeS: opens Pages
menu; selects active
panel for combo
display
MenU: opens
context &
settings menus
LIGHT/POWeR:
controls backlight
level & turns the
unit on/off
WPT/FInD: saves a waypoint
at current position; accesses
searching tools
MMC/SD Card slot: insert
MMC/SD and high-detail
mapping cards here
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Getting Started
Turning on the Unit
Press the POWeR/LIGHT key to turn on the unit. If the unit is not connected to
a transducer, the unit will start up in simulator mode. To turn off the unit,
press the POWeR/LIGHT key for three seconds.
Keypad
Keypad
This unit’s keypad can be used in two ways. Pressing the arrow sym-
bols on the keypad will move the cursor in the corresponding direc-
tion on the screen and allow you to scroll through menus.
Backlight
Tap the LIGHT/POWeR key to make adjustments to the
backlight level and open the Backlight Menu. To turn on Night
Mode from the menu, highlight Night Mode and press enTeR.
Night mode optimizes the display for low light conditions.
Cursor
Use the unit’s keypad to move the cursor around the display, select onscreen objects,
highlight data items and view sonar history. Press exIT to remove the cursor from
the screen.
Language
Selects language used for menus, text boxes and messages.
To select a language:
1. Press MenU twice.
2. Select System and press enTeR
3. Highlight Language and press enTeR.
4. Use the keypad to select a language
and press enTeR.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Menus
This unit has a Settings menu, a Pages screen and several context
menus. The Settings menu provides access to the settings menus for
the three main operation modes: Sonar, Chart and Radar. The Settings
menu is accessed by pressing MenU twice.
The Pages screen allows you to select a page to be shown on the
display. Utilities are also accessed from the Pages screen. Press the
PAGeS key to select a page.
Each page has its own context menu which allows you to access
functions for that page. Context menus are accessible only when its
corresponding page is displayed. The Sonar Menu, for example, will
only be available when the Sonar Page is on the display. To access a
context menu, select the desired page and press the MenU key.
Settings
menu
Pages screen
Chart menu
Radar menu
Sonar menu
Closing Menus
Press the exIT key to close a menu. Repeatedly pressing exIT will close all menus,
taking you back to the main screen.
Selecting Chart Data
This unit supports three types of map data:
Navico, Navionics and Navico 3D (US only).
To use Navionics or Navico 3D data, you
must select it from the Chart Data menu.
To select Chart data:
1. Press MenU twice.
2. Highlight Chart and press enTeR.
3. Select Chart Data and press enTeR.
4. Select the desired map data option and press enTeR.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Selecting a Fishing Mode
Fishing modes enhance the performance of your unit by
providing preset packages of sonar settings geared to specific
fishing conditions.
To select a fishing mode:
1. Press MenU twice.
2. Select Sonar and press enTeR.
3. Highlight Fishing Mode and press enTeR.
4. Select the desired fishing mode and press
enTeR.
Fishing Mode Options
General Use
Shallow Water
Fresh Water
Deep Water
Slow Trolling
Bottom brown/blue background; 50% ping speed
Bottom brown/white background; best suited for
depths less than 100 feet
Bottom brown/white background; 50% ping speed
Deep Blue; 50% ping speed; 50kHz is primary
transducer frequency
Bottom brown/white background; 50% ping speed
Bottom brown/white background; slightly lower chart
speed
Fast Trolling
Clear Water
Bottom brown/white background; 50% ping speed
Bottom brown/blue background; higher ASP; slightly
lower chart speed
Brackish Water
Entering Letters in Text Boxes
This unit has some features and functions that may
require you to enter data in a text box.
Keypad button controls
uppercase & lowercase
To enter data in a text box:
1. HighlightthetextboxandpressenTeR.
A keyboard will appear on the screen.
2. Use the keypad to highlight the first
character and press enTeR. Repeat
this step until all characters have been
entered.
3. Highlight OK and press enTeR.
Keyboard window
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Restore Defaults
The Restore Defaults command switches the unit back to the settings it had when
you purchased it (default settings),
To Restore Defaults:
1. Press MenU twice.
2. Select System and press enTeR.
3. HighlightRestore Defaults and press enTeR.Aconfirmation message
will appear.
4. Select Yes and press enTeR.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Pages
Page icons
rotate around
the circular
Pages
With Sonar selected, unit will
display a full sonar screen
menu
Combo
display
options
allows you
to display a
split screen
Sonar icon rotated to center of
page; has blue border indicating
Page Icons
it is the selected page option
Pages Screen
Consists of four page icons that scroll horizontally around the Pages menu. To view the pages screen,
press the PAGeS key.
Selecting Pages
Pressing the keypad left or right will move the page icons around the menu. To select a page, move
the desired page icon to the center of the screen.
When selected, the page name will be highlighted in blue at the top of a list of combo display options.
Its icon, will be framed by a blue border below the list. To display the page, press enTeR.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Data Overlay
Data overlay is information you can display on top
of the page screen, allowing you to customize each
page with desired data.
Data Overlay menu
Every page option has its own Data Overlay menu. The menu allows you to edit,
add or remove overlay data from the display. To access Data Overlay menu, select
a page option and press MenU.
NOTE: Adjusting Panel Sizes is covered later in this section in
the Displaying Combo Pages segment.
Edit Overlay menu
Accesses data overlay options for all the unit’s page screens.
To access Edit Data Overlay menu:
1. Select Edit Data overlay from the Data Overlay
menu and press enTeR.
2. Press MenU. The Edit Overlay menu will appear
with Add Gauge selected.
Edit Overlay menu
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Edit Mode
When a gauge is added to the display it will be shown in edit mode. Analog and
bar gauges are shaded in blue when they are in Edit Mode. Digital Gauges will be
shown with a blue border.
Digital gauge in edit mode
Analog gauge in edit
mode
Move or Placing a Gauge
The Move gauge command allows you to move data overlay to any position on the
screen. When you use the Place gauge command, the gauge will be locked in its
current position.
To move or place a gauge:
1. Press the enTeR key when the gauge is in Edit
mode. Four directional arrows will appear when
the gauge can be moved.
2. Use the keypad to move the gauge to a desired
location on the screen.
3. Press enTeR to place the gauge.
Select Data
Used to select data that will be shown on the data overlay display. When selecting
data you first will open a main data category and then choose data to be displayed
from the a data subcategory.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Select data menu
Time subcategory
To select data overlay:
1. Press the Select data softkey. The Select Data menu will appear.
2. Use the keypad to select the desired category and press enTeR.
A list of subcategories will appear.
3. Select the desired subcategory and press enTeR.
Type
Switches data overlay display between analog, digital and bar gauge formats,
provided the format is appropriate for the selected data type.
To change Type press the Type softkey to toggle between digital and analog gauge
formats.
Time in digital format
Time in analog format
Size
Selects the size of the data overlay display. Data overlay can be displayed in four
sizes.
With the gauge in edit mode (shaded in blue) press the ZOOM OUT key to increase
overlay size; press the ZOOM In key to decrease overlay size.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Small digital gauge
Large analog gauge
Limits
Controls the number scale used on data overlay gauges and
selects warning thresholds. Changing the limits on an analog
or bar gauge removes unnecessary numbers from the gauge,
making them easier to read. Warnings help you stay within
selected warning thresholds.
Limits are configured by inputting analog or bar gauge limits
in the Limits text boxes — minimum and maximum. Warnings
thresholds are entered in the Low and High text boxes.
Configuration
Limits menu
To configure limits:
1. Press the Limits softkey. The Configuration Limits menu will
appear.
2. Select the Limits or Warnings text box and press enTeR.
3. Use the keypad to enter the desired threshold.
4. Select OK and press enTeR.
To save changes:
1. Press MenU and highlight Save.
2. Press enTeR.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Configuration menu
Allows you to Add/Remove sources and adjust Bezel, Caption
and Invert Text Settings. Other configuration menu options are
covered previously in the section.
To access the Configuration menu, highlight Configuration on
the Edit Overlay menu and press enTeR.
Configuration Settings
Adds a bezel to the data overlay gauge, making it easier to
see against certain backgrounds
Bezel
Caption
Allows you to add/remove data label from gauge
Invert Text Changes appearance of data overlay text
Add Source
Displays the same type of data from different sources on
the same analog gauge.
If, for example, you have multiple engines, you could
select port engine RPM as your data type and then display
starboard engine RPM using the Add source command.
Both data sources could be displayed simultaneously on
an analog gauge with two needles; one dedicated to each
source.
Add Source menu
To use Add Source:
1. Select Add Source from the Edit Overlay menu
and press enTeR. The Add source menu will
appear.
2. Highlight a category a press enTeR. A list of
subcategories will appear.
Analog gauge
showing RPM from
two engines.
3. Select the desired subcategory and press
enTeR.
To remove add source data:
1. Highlight Remove source from the Edit Overlay menu and press
enTeR. A list of sources will appear.
2. Select the source you want to remove and press enTeR.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Sonar Page
Displays the water column moving from
right to left on your unit’s screen. On the
right side of the screen, the Amplitude
Scope bar previews echoes about to appear
on the display.
The sonar page has three splitscreen view
settings and 14 color palette settings. Sonar
display options are covered in more detail
in the Sonar Operation section.
On the Sonar Page you can:
•
•
•
Move the cursor to any location on the screen to get a depth reading
Show fish echoes as fish symbols with fish depths
Adjust Range to view only desired portion of the water column
To access the Sonar Page, use the keypad to highlight Sonar on the Pages menu and
press enTeR.
Chart Page
Consists of a Map that moves in real time
as you move. By default, the map is shown
from a birds-eye view with North at the top
of the screen.
This page has three map orientation options
(North Up, Track Up & Course Up) and
two ways to view the map: 2D and Shaded
Relief (only available on select models).
The cursor is used to scroll the map, select
objects and find the distance between objects. The Chart page is covered in more
detail in the Chart Operation section.
On the Chart Page you can:
•
•
•
Save Waypoints
Find points of interest (POI)
Navigate routes; navigate to cursor and waypoints
To access the Chart page, use the keypad to highlight Chart on the Pages menu and
press ENTER to access the Chart Page.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Radar Page
Displays the PPI (Position Plan Indicator)
screen, Range Rings and the cursor.
The PPI can be shifted to show more of a
desired portion of the screen (Look Ahead,
Center & Offset) and the color palette
can be changed to show returns in white,
yellow, black or green. The radar page
is covered in more detail in the Radar
Operation section.
On the Radar Page you can:
•
•
•
Overlay compass data, range rings and EBL/VRMs on display
Choose screen orientation from Head Up, Course Up & North Up
Make radar targets more visible via Target Expansion
Use the keypad to highlight Radar on the page screen and press enTeR to access
the Radar Page.
NOTE: You will only be able to see the Radar page if your unit
is connected to a radar.
Info Page
Consists of multiple gauges — Analog, Digital
and Bar — that can be customized to display
selected data. Customizing the info page allows
you to monitor several types of desired data at
the same time.
On the Info Page you can:
•
•
•
Select data to be displayed in analog gauge or digital formats
Change the page layout using one of three templates
Select the range (scale) of analog gauges
To access the Info Page, use the keypad to select Info on the pages screen and press
enTeR.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Data menu
Controls Info page data, page layout and data display format
selection. To access the Data menu, press MenU while on the
Info page.
Dash 1, Dash 2 and Dash 3
Data menu
Info Page dashboard templates that vary in page layout and in the
number of gauges supported. The templates save you time by allowing you to use the
Info page without having to manually set up a gauge layout.
Gauge Layout Templates
General Engine
Layout
Digital Layout
Bar Layout
You can change the gauge layout of Dash 1 (General Engine Layout), Dash 2 (Digital
Layout) and Dash 3 (Bar Layout) templates using the change layout command. To
select a dashboard template, highlight the desired template on the Data menu and
press enTeR.
NOTE: You can toggle through the dashboard templates on the
screen by pressing the keypad left/right.
Edit
Used to select information displayed on the Info page. To switch the screen to Edit
Mode, select Edit from the Data menu and press enTeR. The active gauge will be
shaded in blue (analog) or surrounded by a blue border (digital and bar).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
To edit gauge display:
1. Use the keypad to select the gauge you want to
edit and press enTeR. The Select Data menu
will appear.
2. Usethekeypadtoselectadatacategoryandpress
enTeR. A list of subcategories will appear.
GPS category
3. Select the desired subcategory and press
enTeR.
4. Press MenU. The Edit Data menu will appear.
5. Highlight Finish Edit and press enTeR. The
Finish Edit Data menu will appear.
Ground Speed
subcategory
6. Highlight the Save button and press enTeR.
NOTE: Press enTeR or exIT to switch gauges into Edit Mode
to Normal Mode.
Editing data on an analog
gauge
Editing data on a digital gauge
Edit Data menu
Changes Info Page gauge data, allowing you to display desired data on analog ,
digital and bar gauges. It also controls gauge limits.
To access the Edit Data menu, switch the screen to Edit mode and press MenU.
NOTE: Select Data, Add Source and Configure Limits are
described in more detail in the previous Data Overlay segment.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
To select data:
1. Highlight Select Data from the Edit Data menu and press enTeR.
The Select Data menu will appear.
2. Use the keypad to select the desired category
and press enTeR. A list of subcategories will
appear.
3. Select the desired subcategory and press
ENTER.
To add source:
1. Select Add Source from the Edit Data menu
and press enTeR.
2. Use the keypad to select the desired category
and press enTeR. A list of subcategories will
appear.
3. Select the desired subcategory and press
enTeR.
To remove a source:
1. Highlight Remove Source from the Edit Data menu and press enTeR.
The Remove data-source window will appear.
2. Select the source you want to remove and press enTeR.
To Configure Limits:
1. Highlight Configure Limits on the Edit Data menu
and press enTeR. The Configure Limits menu
will appear.
2. Select the desired text box and press enTeR.
3. Use the keypad to enter the desired limit or
warning threshold.
4. Select OK and press enTeR.
NOTE: The Limits portion of the Configure Limits menu will
only be shown when configuring analog gauge limits.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
To Finish Editing:
1. Select Finish Edit from the Edit Data menu and press enTeR.
A confirmation message will appear.
2. Select Save and press enTeR.
Change Layout
Controls the gauge layout of dashboard templates and customized dashboards. That
allows you to select a desired gauge layout template for all dashboards.
To change layout:
1. Highlight the desired dashboard and
press enTeR.
2. Select Change Layout from the Data
menu and press enTeR.
3. Use the keypad to choose a gauge
layout template and press enTeR.
Add Dashboard
Allows you to customize and save multiple dashboard templates. Desired data can
be added to the gauges on each dashboard, allowing you to create custom dashboards
for a variety of fishing conditions. You can even use the same gauge layout template
for each dashboard.
When you have created all desired dashboards, press the keypad left/right to toggle
through your dashboards.
To add a dashboard:
1. Select Add Dashboard from the Data menu and press enTeR. The
Change Layout menu will appear.
2. Select the desired gauge layout and press enTeR. Refer to the
previous Edit segment to customize the dashboard.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
To remove dashboards:
1. Select the number of the dashboard you want to
delete from the numerical dashboard list.
2. Highlight Remove Dashboard and press enTeR.
A confirmation message will appear.
Numerical
dashboard list
3. Select Delete and press enTeR.
Settings
Opens the Settings menu. Settings information is covered in detail in the Settings
menu section.
Utilities
Allows you to set alarms, view sonar logs and access other
system settings.
To access Utilities:
1. Use the keypad to center the utilities icon on
the screen.
2. Scroll down the list of utilities until the desired
option is highlighted.
Utilities Icon
3. Press enTeR.
Utilities
Waypoints,
Access Waypoint, Route and Trails screen; covered in
Routes/Trails
the Chart Operation Section
SearchforPOIs,Vessels,Coordinates,Trails,Waypoints
and Routes; covered in Chart Operation Section
Find
Alarms
Access alarm history, status and change settings
View status and messages from vessels in the area
Displays time when sun and moon will rise/set
Vessels
Sun/Moon
Trip Calculator Keeps running tally/total of engine hours
Files
Access, copy and delete data files and sonar logs
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Copying a screenshot
Copy File screen
To copy data files/sonar logs:
1. Highlight Files from the Utilities menu and press enTeR.
2. Select the desired File category and press the keypad to the right. A
list of subcategories will appear.
3. Select a subcategory and press the keypad to the right. Highlight
the desired data file/sonar log.
4. Press MenU. Highlight Copy and press enTeR. The Copy File
screen will appear.
5. Select a place to copy the file, like an MMC card. Press enTeR.
To delete data files/sonar logs:
1. Highlight Files from the Utilities menu and press enTeR.
2. Select the desired File category and press enTeR. A list of
subcategories will appear.
3. Select a subcategory and press enTeR.
Highlight the desired data file/sonar log.
Copy and Delete buttons will appear at the
bottom of the screen.
4. Select the Delete button and press enTeR. A confirmation message
will appear.
5. Select Yes and press enTeR.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Info selected as combo
display option
GPS/Info combo page
Displaying Combo Pages
You can display multiple pages at the same time by scrolling the
desired page’s icon to the center of the screen and then choosing a
secondary page from the list of combo page display options.
To display a combo page:
Primary page
1. Use the keypad to select the first page for the combo
display. This is the primary page, which will be
displayed in the left panel.
2. Select another page from the primary page’s combo
display list. This is the secondary page. It will be
displayed in the right panel.
Secondary
page
3. Press enTeR. The selected combo page will be
displayed.
Selecting an Active Page
When combo pages are displayed only one panel
can be active at a time. The panel outlined with
an orange border is the active page. You will only
be able to access the context menu of the active
panel. Pressing the MenU key will open the active
panel’s context menu.
To switch the active setting to the other panel, hold
down the PAGeS key for 1 second.
Chart panel is active as
shown by the orange border
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Displaying Multiple Panels
Multiple panels can be displayed by setting up a combo display using a page that
supports the Split feature. By displaying multiple panels, you can view more
information on the screen at one time.
Step 1: Select sonar split screen
To display multiple panels:
Step 2: Choose page from
combo display options list
1. Select a Split view for the sonar page. (Accessing the Split feature
is covered in detail in the Using
your Sonar section.)
2. Press the PAGeS key and use
the keypad to center the Sonar
icon on the screen.
3. Use the keypad to select Info
Page from the combo page
display list. Press enTeR. The
combo page will be displayed
with the Sonar split view on the
left; the Info page on the right.
Flasher, normal sonar and the
info page shown on a multi-panel
display.
Adjust Panel Sizes
Controls the size of panels when combo pages or
multi-panels displays are in use. Adjusting the size
of the panels, allows you to emphasize the panel
you want to see more clearly.
Panels can only be adjusted left/right, so
the panels on the side with the split view
can not be adjusted vertically.
Adjust panel sizes selected
on the Data Overlay menu
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Moving panel cursor left/right will change the size
of each panel
Adjusting panels on combo page
To adjust panel sizes:
Adjusting panels on multi-panel
display
1. With the combo page or multi-panel display on the screen, press
the PAGeS key.
2. Press MenU. Highlight Adjust Panel Sizes from the Data Overlay
menu and press enTeR.
3. Press the keypad left/right to adjust the panels to a desired size and
press enTeR.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
Blank page
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
Sonar Operation
Temperature Graph
Fish Arches
Surface clutter
Water column
Range
scale
Depth
Line
Brush
Water depth, water
Colorline
Cursor
temp and cursor
Amplitude Scope
coordinates
— shows amplitude
of real-time sonar
echoes
Blue sonar history bar; reviews
recent sonar history
To access the Sonar Page:
1. Press the PAGeS key.
2. Use the keypad to select Sonar and press enTeR.
Cursor
Blue sonar history bar
Viewing Sonar History
You can review your recent sonar histo-
ry by moving the cursor to the left until
the screen starts to move in reverse.
To resume normal sonar scrolling, move
the cursor to the right until the blue sonar
history bar at the bottom of the screen is
all the way to the right. Press exIT to
remove the cursor from the screen.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
Sonar Menu
Accesses features ranging from Auto Sensitivity and
Depth Range to Frequency and Stop Sonar.
From the Sonar Page, press MenU to access the Sonar
Menu.
Sensitivity
Sonar Menu
Controls the level of detail shown on the display. Increasing
Sensitivity will show more detail on the screen; decreasing Sensitivity displays less.
Too much detail will clutter the screen. Conversely, desired echoes may not be
displayed if Sensitivity is set too low.
Sensitivity set to 80 percent
Sensitivity set to 60 percent
NOTE: By default, Sensitivity is set to auto mode. You may
have to turn off Auto Sensitivity to set sensitivity to a desired
level. Auto Sensitivity is covered in more detail later in this
section.
Auto Sensitivity
Keeps sensitivity at a level that works well under
most conditions, reducing the need for adjustments.
You can make minor changes to sensitivity with Auto
Sensitivity turned on, but you will have to turn it off
to make significant adjustments.
Auto Sensitivity can be turned on/off by selecting Auto Sensitivity from the Sonar
menu and pressing enTeR.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
Colorline
Wide yellow hard
sonar return
Reddish-blue soft
sonar returns
Distinguishes strong sonar echoes from
weak sonar echoes. That makes it easier
for you to distinguish fish or structure from the
bottom.
A hard return will be shown as a wide, bright
yellow line, whereas a soft return will be a
narrow reddish-blue line.
Range
Used to select the section of the water column — from surface to bottom — shown
on the display. When there is a portion of the water
column you want to focus on, select a range from
the Depth Range menu that includes the desired
area.
Range set to 60 feet
The values on the Range menu determine the depth
shown on the display. If you selected 20m from the
range menu the unit will display 0-20m of the water
column, regardless of the water depth. There are
21 depth ranges, including automatic and custom
settings. The automatic setting will set the range
from the water surface to water depth.
Frequency
This unit supports three transducer frequencies; two of which are supported by your
transducer. 200 kHz has the highest sensitivity and best target discrimination in
shallower water; 83 kHz offers a wider cone angle for greater water coverage and
50 kHz provides the best depth penetration. You can view both available frequencies
at the same time by setting up a sonar split screen.
Split
Adjusts the configuration of sonar page display using one of four options: No Split,
Zoom, Bottom Lock and Flasher.
Zoom display
Bottom Lock
Flasher Display
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
•
no Split — displays full sonar screen
•
Zoom — splits display with a zoomed-in panel on the left (press
ZOOM key to increase zoom) and a normal sonar view on the right
•
•
Bottom Lock — splits the display with a 2X zoom on the left; a normal
sonar view on the right. Keeps the bottom on the screen at all times.
Flasher — splits the display with a flasher-style sonar on the left; a
normal sonar view on the right
Stop Sonar
Pauses the sonar chart, allowing you to get a closer look at sonar echoes.
Adjust
Sensitivity and Colorline can also be adjusted from the Sonar menu by using the
Adjust command.
To Adjust Sensitivity and Colorline:
1. Highlight Adjust on the Sonar menu
and press enTeR. Press the keypad
up/down to select the Sensitivity or
Colorline scrollbar.
2. Press the keypad left/right to make
adjustments.
3. Press exIT.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
Custom — Upper and Lower Limits
Controls not only the depth range (lower limit), but
also lets you choose the upper limit. So, instead of
a selecting a range that includes the water surface,
you can choose upper and lower limits anywhere
along the water column. The Upper and Lower
limit must be at least 2 meters apart.
To set Upper and Lower Limits:
1. Select Range and press enTeR.
2. Highlight Custom and press enTeR.
Upper limit is 15 feet; lower
limit is 65 feet
The Upper and Lower Limit window will appear.
3. Select the Upper or Lower Limit dialog box. Press enTeR. The
numerical keypad will appear.
4. Use the keypad to enter the desired value in the corresponding
upper or lower limit dialog box. Press enTeR.
5. Repeat Steps 3 and 4 to input the desired limit in the other dialog
box.
Ping Speed
Ping Speed controls the rate the transducer uses to
send sonar waves into the water. A higher ping speed
will yield the best results when you are moving across
the water at a high rate of speed or fishing from a dock. The reverberation of too
much ping speed can cause interference on the screen.
When using two units on your boat, lowering the ping speed of one of the units will
prevent interference (cross-talk) caused by one transducer detecting pings from the
other transducer. The default setting is suitable for most conditions. Highlight Ping
Speed on the Sonar menu and press the keypad left/right to make adjustments.
Sonar Options
Adjusts display settings and the configuration of the
display. The Sonar Options menu allows you to split the
screen between two sonar views, change the color of
the display, use Fish ID and add graphical elements to
screen that will enhance your sonar experience.
To access the Sonar Options menu, select Sonar Options
from the sonar menu and press enTeR.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
To select a Split option:
1. From the Sonar Options menu,
highlight Split and press enTeR.
The Split menu will appear.
2. Use the keypad to select the desired
option and press enTeR.
Palette
Sonar display color templates with varying degrees of color
and brightness. On the Palette menu, you can select a sonar
display template suited for your fishing conditions from 14
palette options.
A bottom brown
palette clearly
separates fish
and structure from
the bottom
Palette menu
To select a Palette:
1. From the Sonar Options menu, highlight Palette and press enTeR.
2. Use the keypad to select the desired palette and press enTeR.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
Temperature Graph
Uses a red line graph with digital display at
the top of the screen to illustrate changes in
Temperature. The Temperature graph makes it
easier to recognize temperature trends.
To turn the Temperature Graph on/off, highlight
Temperature Graph on the Sonar Options menu
and press enTeR.
Temperature graph
Depth Line
Depth Line
Displays a dark line over the bottom surface,
making it easier to distinguish the bottom from
fish, trees and other objects.
To turn on/off the Depth Line, select Depth Line
and press enTeR.
Amplitude Scope
Allows you to see the amplitude of real-time echoes as they appear
on the display. The Amplitude Scope displays live returns even when
you are viewing your sonar history. To turn off the Scope, highlight
Amplitude scope on the Sonar Options menu and press enTeR.
Amplitude Scope
Zoom Bars
When your unit is in Split Zoom mode, zoom bars show which echoes will be
displayed on the screen when the display is zoomed in to a particular zoom range.
Only echoes shown between the top and bottom of a zoom bar will be displayed at
that selected zoom range.
To turn on/off Zoom Bars, highlight Zoom Bars on the Sonar Options menu and
press enTeR.
NOTE: When the screen is zoomed, you can use the Zoom
Pan feature to scroll up and down the water column. That
allows you to see portions of the water column not visible at
the selected zoom range. When turned on, Zoom Bars will
appear when the Zoom in key is pressed.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
Fish ID
Displays fish echoes as fish symbols instead of
fish arches with or without depth. This makes
it easier to recognize fish on the sonar display.
Symbols — places a fish symbol where a
fish is detected.
Depths — places depths above each fish
detected; helps gauge the distance from each
fish symbol to the boat.
Fish Symbols and Depths
Both — turns on both Symbols and Depths.
To select Fish ID option:
1. Highlight Fish ID and press enTeR.
2. Use the keypad to select Symbols, Depths or Both and
press enTeR.
Log Sonar Data
Used to save sonar chart data to your unit’s internal memory or to an MMC/SD
card.
To access the Sounder Logging menu, select
Log Sonar Data from the Sonar menu and press
enTeR.
Log Sonar Menu
Input the desired name for the sonar log file
Filename
Selects location where sonar log will be saved/stored
Save to
Controls number of bytes per sounding. More bytes yields
better resolution/shorter logging time; conversely, fewer
bytes produces longer sonar logs/lower resolution
Bytes
Recording time left until memory storage runs out
Time Remaining
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
To input filename:
1. Highlight the Filename text box and
press enTeR. A keyboard will appear
on the screen.
2. Use the keypad to input the desired
filename.
3. Select OK and press enTeR.
Filename keyboard
Bytes per sounding
menu
Internal selected on device menu
To select Save to or Bytes per Sounding:
1. Highlight Save to or Bytes per Sounding from the Sounder Logging
menu and press enTeR.
2. Use the keypad to select the desired option and press enTeR.
Start Logging
A sonar log is a recording of sonar activity displayed on
the sonar page.
To record a sonar log, highlight the Start Logging button
and press enTeR.
When a sonar log is being recorded, a blinking red circle
will be displayed in the upper left-hand corner of the
screen and a logging message will appear periodically
at the bottom of the screen.
Logging Indicator blinks
when sonar is being
recorded
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Sonar
To stop logging:
1. Select Stop from the Sounder Logging
menu and press enTeR. The Stop
Logging menu will appear.
2. Highlight the Stop Logging button and
press enTeR.
Stop Logging menu
NOTE: Refer to the Utilities segment of the Pages section for
information on copying and deleting files.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
Chart Operation
Displaying the Chart page
To access the Chart
page, press the Pages
key to bring up the Pages
menu. Use the Arrow
keypad to select Chart
and press Enter.
Access the Chart page from the Pages menu.
Chart page (2D Chart mode)
Point of Interest (POI)
Waypoint
Chart orientation indicator
Cursor coordinates
Map scale
Current position icon
Cursor
Download from Www.Somanuals.co3m9. All Manuals Search And Download.
Chart
The previous image shows some of the different items you will see when viewing
the Chart page:
•
Point of Interest (POI): A position on the Chart page represented by
a symbol or character.
•
Cursor: Used to view specific areas on the Chart page, select POIs,
create waypoints and measure distances. When the cursor is on-
screen, pressing the exit key will toggle between the cursor's location
on the Chart page and your actual position. As long as the cursor is
on the Chart page your actual position may not be visible.
•
•
•
•
•
Chart orientation indicator: Indicates the current direction the Chart
page is facing.
Cursor coordinates: Displays the coordinates of the cursor on the
Chart page.
Waypoint: An electronic address based on the latitude and longitude
of a selected Chart location.
Map Scale: Represents the relationship between the distance on
the Chart page and the real distance on the earth's surface.
Current position icon: Represents your current position.
Find Current Position
Power on the unit and display the Chart page. The current position icon represents
your current position on screen. The icon always points to your heading.
If the current position icon displays a question mark then the unit has not
achieved a satellite lock and is not tracking your current position. When
sufficient satellites are received to determine a position, the icon's move-
ment will correspond with your movement.
Chart menu
Use the Chart menu to adjust settings and enter commands.
From this menu you have access to routes, waypoints,
info, chart options and screen settings. To open the Chart
menu, go to the Chart page and press the MenU key. The
following features are listed in the order they appear on the
Chart menu, top to bottom:
•
•
•
New Waypoint: Creates a new waypoint.
New Route: Creates a new route.
Go to Cursor: Navigates to the cursor position
on the Chart page.
Chart menu
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
•
Find: Opens the Find menu. From the Find menu you can search for
items by select categories.
•
•
Info: Shows a list of items close to the cursor.
Measure: Used to measure the distance between current position
and another point on the Chart page or between two different points.
•
•
Overlay: Toggles radar overlay overlay on or off.
Chart options: Opens the Chart options submenu which contains
the Map Orientation, Look Ahead, Chart categories and Imagery fea-
tures.
Map Orientation controls the way the Chart
page moves in relation to your movement. The
Map Orientation settings are North Up, Head-
ing Up and Course Up.
Look Ahead increases the view of your track.
Chart categories opens the Chart Categories
screen.
Chart options submenu
Imagery selects between 2D and Shaded Relief
mapping (only available on select models).
•
Settings: Opens the Settings menu.
Selecting POIs on Chart page with Cursor
To select a Chart page POI:
1. From the Chart page use the
Arrow keypad to center the
cursor over a POI. A pop-up
box will appear describing the
POI. The POI's coordinates are
displayed in the lower left hand
corner of the Chart page.
Download from Www.Somanuals.co4m1. All Manuals Search And Download.
Chart
Waypoints
A waypoint is the latitude and longitude of a specific position on the earth's surface.
You can quickly create a waypoint at your current position or you can create a way-
point at the cursor's position on the Chart page. You also can create a waypoint at
any location by manually entering the position's latitude and longitude.
Waypoints are important because they can be saved in the unit and later used to find
your way back to a specific location, such as a favorite fishing spot or an important
geographical feature. To quickly save a waypoint at the vessel's current position
press the WPT/FInD key.
Create/Delete Waypoint from Chart page
To create a Waypoint at the Cursor's
position on Chart page:
1. Place the cursor on the Chart
page where you want to set the
waypoint and press enTeR
twice. The New Waypoint
menu will appear.
2. Select Save from the New
New Waypoint at Cursor menu
Waypoint menu.
To create a Waypoint at the Vessel's position on Chart page:
1. Press the MenU key. From the Chart menu select New Waypoint.
2. When the New Waypoint at Vessel menu appears, select Save.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
To Navigate to a Waypoint from the Waypoints screen:
1. From the Pages screen select Waypoints, routes, trails, press enTeR.
When the Waypoints screen appears select the waypoint you want to
navigate to from the waypoints list and press MenU. The Waypoints
screen menu will appear. From the Waypoints screen menu select
Go to.
Waypoints screen
To view stored waypoints go to the Waypoints screen in the Utilities page. From the
Waypoints screen you can view and edit stored waypoints.
Waypoint name
Waypoint latitude
Waypoint icon
and longitude.
Time and date the
waypoint was created.
Download from Www.Somanuals.co4m3. All Manuals Search And Download.
Chart
Waypoints screen menu
To open the Waypoints screen menu, press
the MenU key from the Waypoints screen.
The following features are listed in the
order they appear in the Waypoints screen
menu, top to bottom:
•
Edit: Opens the Edit Waypoint
menu.
•
New: Opens the New Waypoint
menu.
•
•
•
•
Show: Shows the Waypoint on the Chart page.
Go to: Select to navigate to the waypoint.
Delete: Deletes selected waypoint.
Sort: Controls how waypoints are sorted in the Waypoints screen
list.
•
•
Delete All: Select to delete all waypoints.
Find: Use to search for waypoints in the Waypoints screen.
Waypoints screen, Search for Waypoint by name
If the waypoint list contains too many waypoints to search through manually, you
can search for a specific waypoint by name.
To Search for Waypoint by Name:
1. From the Waypoints screen
press the MenU key. The
Waypoints screen menu will
appear.
2. From the Waypoints screen
menu select Find. A keypad
will appear. Use the keypad to
enter the name of the waypoint
you are searching for and press
OK.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
Waypoints screen, Sort Waypoints
feature
You can choose how waypoints are sorted in
the Waypoints list by selecting Sort from the
Waypoints screen list menu. Waypoints can be
sorted by Name, Nearest or Icon. By default the
unit stores waypoints by name.
Waypoint Information screen
When a waypoint is saved to the Chart page, you can view detailed information
about that saved waypoint.
To view waypoint information:
1. Place the cursor over the waypoint
and press the MenU key.
2. Select Info and press enTeR.
editing a Waypoint on the Chart page
To Edit a Waypoint from the Chart page:
1. Place the cursor over the waypoint and press the enTeR key. The
Edit Waypoint menu will appear.
edit Waypoint menu
The Edit Waypoint menu is used to edit waypoint
settings and coordinates. Use this menu to change
the name, icon, color and description of a way-
point.
Edit Waypoint, More options:
Select More from the Edit Waypoint menu and the following edit options will ap-
pear:
•
•
•
•
Name: Edit the name of a waypoint.
Position: Enter a latitude or longitude for a waypoint.
Icon: Select a different waypoint icon.
Color: Change waypoint icon color.
Download from Www.Somanuals.co4m5. All Manuals Search And Download.
Chart
•
Description: Input additional way-
point information.
•
Display: Choose how a waypoint will
be displayed on Chart page.
•
Depth: Select waypoint depth.
•
Alarm Radius: Input distance that
sounds alarm when near a specific
waypoint.
•
•
•
Delete: This will delete a waypoint.
Save: Saves your waypoint changes.
Cancel: Cancels any waypoint changes.
edit Waypoint name, description, position or depth
To Edit Waypoint name or description:
1. From the Edit Waypoint menu, select
the Name or Description text box
and press enTeR. The Waypoint
keypad will appear.
2. Use the keypad to enter the desired
waypoint name and select OK.
To Edit Waypoint position:
1. From the Edit Waypoint menu select the
latitude or longitude text box and press
enTeR.
2. Use the Arrow keypad to input the desired
latitude or longitude and select OK.
To Edit Waypoint depth or alarm radius:
1. From the Edit Waypoint (More) menu select the Depth or Alarm
radius text box and press enTeR. A numerical keypad will appear.
2. Use the keypad to input the desired depth or alarm radius and press
enTeR.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
edit Waypoint icon and color
You can change the default waypoint icon and color from the Edit Waypoint menu.
Edit Icon m
Use the Edit Icon menu and Edit
Icon Color menu to change the
appearance of icons on the Chart
page.
Icon color palette
Routes
Routes make it easier to plan trips to desired destinations and backtrack to a previous
location. Aroute is a series of waypoints linked together to mark a course of travel. A
route must have at least two waypoints. The route segment between two waypoints
is called a leg.
The legs of a route are based on straight lines between waypoints. A route gives you
the ability to navigate to several waypoints in an ordered sequence without having
to manually select the next waypoint in the series.
Create Route from Chart page
To create a new route open the Chart menu and select New Route. You can use the
cursor on the Chart page to create a route.
To Create a New Route from the Chart page:
1. Press the MenU key and select New Route from the Chart menu,
press enTeR.
2. Move the cursor to the start of the route and press enTeR to set
the first waypoint. Move the cursor to the next location and press
enTeR to set a second waypoint.
Download from Www.Somanuals.co4m7. All Manuals Search And Download.
Chart
1. Repeat Step 2 until you have set all the desired waypoints along
the route.
2. Press the MenU key to open the Edit route menu. Select Save and
press enTeR. The route will be saved to the Routes screen.
3. From the Routes screen highlight the route and select Start. The
Start Route message box will appear, select Forward.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
Routes screen
To view stored routes go to the Routes screen in the Utilities page. From the Routes
screen you can view and edit stored routes.
End of route
Route length
name.
Route name
Start of route
Number of legs
name.
in route.
Routes screen menu
From the Routes screen menu you can create a new route, edit a route or start a
route. To open the Routes screen menu, from the Routes screen, press the MenU
key. The following features are listed in the order they appear in the Route screen
menu, top to bottom:
•
•
Edit: Opens the Edit Route screen.
New: Opens the New Route
screen.
•
Show: Shows the Route on the
Chart page.
•
Start: Select to start navigating a
route.
•
Delete: Deletes a selected route.
•
Delete All: Deletes all routes in the
Route screen.
•
Find: Use to search for routes in the Routes screen.
Download from Www.Somanuals.co4m9. All Manuals Search And Download.
Chart
To Edit Route:
1. From the Routes screen select
the route to be edited and press
enTeR. The Edit Route screen
will appear.
2. From the Edit Route screen you
can edit the route name, display
and waypoints in the route.
3. Use the Arrow keypad to select
which route feature you want to
edit and press enTeR.
Edit Route screen
To Display / Hide Route:
1. From the Routes screen select the route from the routes list, press
enTeR. The Edit Route screen will appear.
2. Highlight the Display check box and press enTeR to either Display
or hide the route from the Chart page.
To Insert, Edit or Remove Waypoints from a Route:
1. From the Routes screen select a route from the route list, press
enTeR.
2. The Edit Route screen will appear.
SelectawaypointfromtheWaypoint
list, press MenU. A small submenu
will appear with the options: Insert,
Edit and Remove.
3. Select Insert and press enTeR to
insert a waypoint into the route. To
remove a waypoint select Remove.
Selecting Edit will bring up the Edit
Waypoint dialog.
To Navigate Route from Routes screen:
1. S elect the route you want to navigate and press MenU. The Routes
screen menu will appear.
2. Select Start from the Routes screen menu The Start Route dialog
will appear. Select Forward to navigate the route forward or Reverse
to navigate the route in reverse.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
To Search for Route by Name:
1. From the Routes screen press MenU. The Routes screen menu
will appear.
2. From the Routes screen menu select Find. A keypad will appear.
Use the keypad to enter the name of the route you are searching for
and press OK.
Trails
A trail is a record of the path you have traveled. Trails not only show you where you
have been, they can be used to retrace your path back to your starting point. On the
Chart page a trail is presented by a solid line extending from the back of the current
position icon.
From the factory, the unit is automatically set to create and record a trail when the
unit is turned on and you are navigating. The unit will continue to record a trail until
the trail length reaches the maximum trail point setting.
When the unit reaches the maximum trail point number it will automatically begin
recording the trail over itself. By default, the unit places a dot (trail point) on the
Chart page every time you change course.
Trails screen
To view stored trails go to the Trails screen in the Utilities page. From the Trails
screen you can view and edit stored trails.
Trail name
Trail colo
Number of Trail
points.
Indicates if Trail is displayed
Indicates if Trail is
on Chart page.
being recorded.
Download from Www.Somanuals.co5m1. All Manuals Search And Download.
Chart
Trails screen menu
From the Trails screen menu you can create a new trail, edit a trail or delete a trail.
To open the Trails screen menu, press the MenU key from the Trails screen. The
following features are listed in the order they appear in the Trails screen menu, top
to bottom:
•
•
•
•
Edit: Opens the Edit Trail
menu.
New: Opens the New Trail
menu.
Show: Brings up the Chart
page and shows the trail.
Display: Select or deselect to
display or not display trail on
Chart page.
•
Record: Select or deselect to
actively record a trail.
Trails screen menu
•
•
•
Delete: Deletes a selected trail.
Delete All: Select to delete all trails.
Find: Use to search for trails in the Trails screen.
new Trail menu
You can edit a trail from the New Trail menu or from the Edit Trail menu once a
trail is created.
To Create a New Trail:
1. From the Pages screen, select Utilities
and press enTeR. The Waypoints and
Routes screen will appear.
2. From the Waypoints and Routes
screen select Trails. The Trails screen
will appear.
3. From the Trails screen, press MenU.
The Trails screen menu will appear.
New Trail menu
4. From the Trails screen menu select New, press MenU. The New
Trail menu will appear, select Save.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
edit Trail menu
The Edit Trail menu is used to edit trail settings and coordinates. Use this menu to
change the trail name, trail color and description of a trail.
To edit a Trail name:
1. From the Trails screen
select the trail to be edited,
press enTeR. The Edit
Trail menu will appear.
2. From the Edit Trail menu
you can edit the name of
the trail by selecting the
trail name box and pressing
enTeR. The Edit Trail
name keypad will appear.
Use the keypad to enter
the desired trail name and
select OK.
Edit Trail menu
Trail line Color options
You can change the default trail line color from the Edit Trail More menu by select-
ing the Trail line color palette option.
Trail line color
palette menu
NOTE: If you record several overlapping trails, changing
the color of the different trail lines is a good way to keep them
separate when viewing them on the Chart page.
Download from Www.Somanuals.co5m3. All Manuals Search And Download.
Chart
Measuring Distances on Chart page
Use the Measure feature from the Chart menu to measure distances between your-
self and another location on the Chart page or between two different points.
To select/deselect Measure feature:
1. From the Chart page press the
MenU key. The Chart menu
will appear.
2. From the Chart menu select
Measure.
3. When the cursor is on screen
the cursor coordinates window
will display distance from your
position to the cursor position
on the Chart page.
4. To measure distance between two different points on the Chart
page, place the cursor over a point and press enTeR, an x will
appear on the Chart page. Distance will be measured from the x on
the Chart page to wherever the cursor is placed on screen.
Search by Coordinates
To search for Chart page POI using coordinates:
1. From the Chart page press the
MenU key. The Chart menu will
appear, select Find. The Find
menu will appear.
2. From the Find menu select
Coordinate.TheFindCoordinate
keypad will appear. Use the
keypad to enter the desired
coordinates and select OK.
Find Chart item
To search for specific Chart page item:
1. From the Chart page press the MenU key. The Chart menu will
appear, select Find. The Find menu will appear.
2. From the Find menu select Chart Items. The Find - Chart Items
screen will appear. Select Name, a keypad will appear. Use the
keypad to enter the name of the chart item and select OK.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
To view a list of specific Chart POI search options select Category from the
Find - Chart Items screen. A drop down list will appear. Select the specific
category from the drop down list.
Map Orientation
To change Chart page orientation:
1. From the Chart page press the MenU key. The Chart menu will
appear, select Chart options. The Chart options submenu will
appear.
2. From the Chart options submenu select Map Orientation. The three
Map Orientation options are: North Up, Heads Up and Course Up.
•
North Up — Displays the Chart page
with North always at the top of the
screen.
•
Heads Up — Displays the Chart page
in the direction the boat is facing.
•
Course Up
—
Displays the Chart
page at the same orientation as your
initial bearing to a destination.
Look Ahead
Keeps your current position at the bottom of the Chart page to display more map
area in front of you.
To select / deselect the Look Ahead feature:
1. From the Chart page press the MenU key. The Chart menu will
appear, select Chart options. The Chart options submenu will
appear.
Download from Www.Somanuals.co5m5. All Manuals Search And Download.
Chart
2. From the Chart options submenu select or deselect Look Ahead to
turn this feature on or off.
Chart categories
Use the Chart Categories screen to control what you want to see on the Chart page.
To select / deselect Chart Categories:
1. From the Chart page press MenU.
The Chart menu will appear; select
Chart options. The Chart options
submenu will appear.
2. From the Chart options submenu
select Chart categories. The Chart
Categories screen will appear.
Select or deselect the chart options
you want to display on screen.
2D and Shaded Relief
(Shaded Relief only available on U.S. models)
To select between 2D and Shaded Relief:
1. From the Chart page press the MenU key. The Chart menu will
appear. From the Chart menu select Chart options. The Chart options
submenu will appear.
2. From the Chart options submenu select Imagery. The Imagery drop
down menu will appear with two map options: 2D and Shaded Relief.
Make your selection and press enTeR.
2D mapping
Shaded Relief, only available
on U.S. models.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
Chart page Icons, Tides and Currents
Use the cursor on the Chart page to view detailed information about selected icons,
including Tides and Currents.
The image, at left, shows a Current icon selected on the Chart page. To view
detailed information about an icon, press the MENU key then select Info from
the Chart menu. From the Chart Info screen, press Details.
Detailed information also can be viewed for Tide icons.
Radar Overlay
Places radar returns on top of the map.
That gives you greater awareness of your
surroundings by allowing you to see radar
returns aligned with actual radar targets.
To turn on radar overlay:
1. Highlight Overlay on the Chart
menu and press enTeR.
2. Select Radar and press
enTeR.
Radar Options menu
Download from Www.Somanuals.co5m7. All Manuals Search And Download.
Chart
Radar Options
The Radar Options menu appears when Radar Overlay is tuned on. It allows you to
customize the radar overlay settings from the Chart Page.
To access the Radar Options menu, select Radar Options from the Chart menu and
press enTeR.
Radar Options menu
Radar State
Selects radar transmission mode
Adjusts Gain, Sea Clutter, Rain Clutter, Interference
Rejection and Target Boost
Adjust
Automatic Gain setting that is suitable for a variety of
conditions
Auto Gain
Selects Sea Clutter setting from auto (harbor, offshore)
and manual settings.
Sea Clutter
Controls the transparency of radar overlay on the map To
Transparency make adjustments, highlight Transparency and press the
arrow keys left/right
NOTE: Radar State, Adjust, Auto Gain and Sea Clutter are
covered in more detail in the Radar Operation section.
Navionics
Your unit offers an unprecedented level of 2D and 3D mapping detail and numerous
mapping options, including Navionics chartcards. Navico mapping data is displayed
by default.
To view Navionics data:
1. Insert your Navonics card in the unit's MMC/SD card slot.
2. Press MenU twice, select Chart and press enTeR.
3. Highlight Chart data and press enTeR.
4. Select Navionics and press enTeR.
NOTE: You can use Navionics Platinum, Gold, Silver, Clas-
sic and HotMaps chartcards with your HDS unit.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chart
navionics Settings menu
Use to customize the way Navionics data will be displayed on the Chart page, allow-
ing you to adjust the features best suited for your fishing conditions.
To change Navionics Settings:
1. Select Chart options from the Chart menu
and press enTeR.
2. Highlight Settings and press enTeR.
3. Select a setting and press enTeR.
4. Highlight the desired option and press
enTeR.
Navionics Settings
menu
navionics Settings and Options
•
Safety Depth — Allows you to display the depth areas corresponding to the
safety contour desired. Available options are:
Off: No depth area displayed.
Other numeric depth values: The areas with depths up to value selected
are displayed in shades going from darker blue (for lower depths) to light-
er blue (for higher depths). The areas whose depths are over the selected
value, and therefore navigable under safety conditions, will be displayed in
white. The Dryline areas are displayed in green.
•
Contours Depth — Used to select the display of depth contours.
NOTE: When Night mode is selected, depth areas are dis-
played from lighter blue (for lower depths) to darker blue
(for higher depths). Depth areas over the value set are dis-
played in black.
Available options:
-5m: display depth contours up to 5 meters (16 feet)
-10m: display depth contours up to 10 meters (33 feet)
-20m: display depth contours up to 20 meters (66 feet)
-All: all depth contours are displayed
Download from Www.Somanuals.co5m9. All Manuals Search And Download.
Chart
•
Texture Type — Enables (on) or disables (off) the 3D shading feature.
Photo overlay allows you to enable (full) or disable (off) the aireal photog-
raphy overlay chart feature.
NOTE: These features are only applicable with Navionics
Platinum™ or Platinum Plus™ charts.
•
Annotation — Allows you to display "Main" names (i.e. city names) only
or the "Full" set of names on the Chart page.
•
Presentation Types — Is used for the selection of the symbols and colors
of the navigation chart "look and feel"; either U.S. or International "paper
chart" presentation types can be selected.
•
Chart Details — This menu is used to select which object types and infor-
mation layers are displayed on-screen.
Available options:
Standard: Equivalent to standard display settings as defined in ECS regula-
tions.
All: Enables the display of all the object types and information layers on
the Chart page.
User: Allows selection of individual object types and information layers
on-screen.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Radar Operation
Range
Range Ring Size
North Indicator
Heading Line
Radar orientation indicator
Range Rings
To access the Radar Page:
1.
2.
Press the PAGeS key.
Use the keypad to select the Radar Icon and press enTeR.
NOTE: You will only be able to see the Radar page if your unit
is connected to a radar.
Radar menu
Use the Radar menu to make adjustments to radar display
settings and features that not only change the appearance of
the display, but also make navigation easier.
To access the Radar menu, press the MenU key when the
Radar page is on the display.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Radar State
Controls radar transmission modes: Off, Transmit and Standby. Off turns off the
radar. Transmit broadcasts a radar signal and standby leaves the radar on, but does
not broadcast a signal.
To select Radar State:
1. Press MenU, highlight Radar State and press enTeR.
2. Select the desired state and press enTeR.
NOTE: It can take 90 seconds or more to transition from Off
to Standby.
Adjust menu
From the Adjust menu you can make adjustments to Gain, Sea clutter, Rain clutter,
Interference rejection and Target boost.
To access the Adjust menu:
1. From the Radar menu select Adjust and press enTeR. The Adjust
menu will appear.
2. Highlight the desired setting and press the Arrow keypad left/right to
make adjustments.
Gain
Controls the sensitivity of the radar receiver. Increasing gain
will show more detail on the screen; decreasing gain will show
less detail. Too much detail will clutter the screen. Conversely,
desired returns may not be shown if gain is too low.
Auto Gain
Selecting Auto gain from the Radar menu will automatically set the sensitivity of
the receiver to a level that works well under most conditions, reducing the need for
adjustments. If you make adjustments to the Gain level when Auto gain is on, Gain
will switch to manual mode.
To select Auto Gain:
1. Press the MenU key. The Radar menu will appear
2. Select Auto gain and press enTeR.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Sea Clutter
Allows you to select the Sea Clutter adjustment mode — Auto or Manual. If you
make changes to Sea Clutter when it is in auto mode (Harbor or Offshore), Sea
Clutter will switch to Manual mode.
Sea Clutter Options
Manual
Harbor
Switches Sea Clutter from Auto to Manual mode
Auto setting optimized for harbor-like environment
Auto setting designed for offshore conditions
Offshore
Rain Clutter
Precipitation reflects radar signals, cluttering the screen. Interference Rejection
reduces or eliminates returns caused by rain, hail, sleet or snow.
Interference Rejection
Reduces interference from other active radars near your vessel. If another ship is
operating radar near you, interference from its radar signals can appear on your dis-
play. Increase interference rejection untrar nterference is eliminated from your
display. Interference Rejection has four Off, Low, Medium and High.
Target Boost (only available on some radars)
This feature increases the size of radar targets, making them easier to see on the
display. Target Boost has four options: Off, Low, Medium and High.
Clear Trails
Clears all target trails from the radar screen. New trails will continue to appear
unless you turn off the target trails feature.
To Clear Trails:
1. Press the MenU key, the Radar menu will appear.
2. Use the Arrow keypad to select Clear Trails and press enTeR.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Position
You can move the PPI (Plan Position Indicator) to different locations on the radar
display. There are three Position options: Center, Look Ahead and Offset.
To change the PPI position:
1. Select Position from the Radar menu and press enter.
2. Select the desired position and press enter.
Position
Default setting, will position the PPI in the center of
the screen
Center
Shifts the PPI to the bottom of the screen, allowing
Look Ahead
you to see more of the area in front of your vessel
Allows you to move the PPI to a any location on the
display. If you shift the PPI to the right, you will see
Offset
more of what is to the left of your boat; if you move
the PPI forward you will be able to see more of the
area behind you
Center: PPI centered on the
display
Look Ahead: PPI moves down,
allowing you to see more of what
is in front of you
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Symbology off
Symbology on
Symbology
Used to turn on/off symbols displayed on the PPI screen, including range rings, range
markers and compass overlay. Rather than turn off each display feature individually,
the Symbology feature allows you to remove them all at once.
To toggle Symbology on/off highlight Symbology on the radar menu and press
enter.
EBL/VRM 1
EBL/VRM 2
EBL/VRM 1 & EBL/
VRM 2 Data Boxes
eBL/VRM
An Electronic Bearing Line (EBL) is a radial line used to show the distance of a
radar target to your vessel. A Variable Range Marker (VRM) is a range ring used to
measure the precise distance to a radar target. Selecting EBL/VRM from the Radar
Menu allows you to place up to two EBL/VRMs on the PPI display.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
eBL/VRM menu
Places selected Electronic Bearing Line and Variable
Range Marker on the display.
To select an EBL/VRM:
1. Press the MenU key.
2. Use the keypad to select the EBL/VRM and
press enTeR.
3. UsethekeypadtomovetheEBLandincrease/
decrease the size of the VRM. Press exIT.
EBL/VRM menu
Adjust
Adjusts size and location of active EBL/VRM.
To adjust an EBL/VRM:
1. From the Radar menu highlight EBL/VRM and press enTeR.
2. Select Adjust and press enTeR.
3. Use the keypad to make adjustments to the EBL/VRM. Press exIT.
Data Box
Data box
Turns on/off on screen EBL/VRM information
box.
To turn on/off the EBL/VRM information box,
highlight Data box on the EBL/VRM menu and
press enTeR.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Cursor position window
When the cursor is active on screen the Cursor position window appears in the
bottom left corner of the Radar page.
Cursor position window
Radar Overlay
Radar Overlay places radar returns on top of
the map on the Chart Page.
That gives you greater awareness of your
surroundings by allowing you to see radar
returns aligned with actual radar targets.
More information on Radar Overlay is available in the Chart Operation section of
this manual.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Radar
Blank page
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Settings Menu
The Settings Menu provides access to installation and advanced configuration
settings for your unit. To access the Settings menu, press MenU twice.
Settings Menu Options
System
Fuel
Vessels
Page
Alarms
Trails
Simulator
Chart (if applicable)
Radar (if applicable)
Sonar (if applicable)
Sirius (if applicable)
Units
Network
System
Used to change system settings like units, language
and key beeps.
To access the System menu:
1. Press MenU twice.
2. Highlight System and press enTeR.
System Menu
Language
Selects the language used on menus and dialog boxes. The default language is
English.
To select a language:
1. Select Language from the System menu and press enTeR.
2. Highlight the desired language and press enTeR. A window will
appear indicating the unit must restart to switch languages.
3. Select Yes and press enTeR. The unit will restart.
Text Size
This unit will display text in two sizes: Small and
Normal. The Text Size menu allows you to select
the size of menu text.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To change Text Size:
1. Highlight Text Size from the System menu and press enTeR.
2. Use the keypad to select the desired text size and press enTeR.
Key Beeps
By default, a tone (key beep) will sound when
any key is pushed on the unit. You can change
key beep volume or turn them on or off from the
Key Beep menu.
Key beeps turned on
To change Key Beep settings:
1. Highlight Key Beeps on the System menu and press enTeR.
2. Select the desired setting and press enTeR.
Time
Used to change local time to offset differences in time zone and to select the way
time and date will be displayed.
To set Time or Date format:
1. Highlight Time on the System menu and press enTeR. The Time
menu will appear.
2. Select the Time format or Date format
dropdown menu and press enTeR.
3. Use the keypad to select the desired
format and press enTeR.
4. Highlight OK and press enTeR.
To set Local Time:
1. Select Local Time on the Time menu and press the keypad left/right
to select the desired offset.
2. Highlight OK and press enTeR.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Datum
A model of the earth’s surface based on a network of surveyed ground features
(points). This unit’s default datum is WGRS-84.
To select a Datum:
1. Select Datum from the Chart settings menu and press enTeR.
2. Use the keypad to select the desired datum. Press enTeR.
Coord System
Controls the coordinate system used when position coordinates are entered and
displayed.
To change Coordinate System:
1. Select Coord System from the Chart settings
menu and press enTeR.
2. Highlight the desired option and press
enTeR.
Magnetic Variation
Converts magnetic north data to true north, increasing the accuracy of navigation
information. The Magnetic Variance Auto setting, automatically converts magnetic
north to true north. When using manual mode, you will have to input the magnetic
variance.
To change magnetic variation settings:
1. Highlight Magnetic Variation on the System menu. Press enTeR.
2. Select Auto or Manual and press enTeR.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Satellite Status
Satellites
Monitors the location of satellites in view and the quality of the unit’s satellite lock-
on. The Satellite page has two display options.
The Satellite screen displays a circular graphic that shows where satellites are
located and a bar graph that monitors the strength of satellites within range of your
unit. Your unit is locked on to satellites shown with blue bars.
To access the Satellite screen select Satellites from the System menu and press
enTeR.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Screen Capture
Saves images of your unit’s screen to your unit. That allows you to capture images
of everything from underwater structure and fish to routes, map areas and radar
targets.
To take a screen capture:
1. Select Screen Capture from the System menu and press enTeR.
2. Press the LIGHT/POWeR key to capture the current screen. Repeat
this step take additional screen captures.
To save screen captures to MMC/SD card:
1. Select Files from the Utilities list on the Pages
menu. Press enTeR.
2. Highlight My Files and press the keypad to the
right. Select screenshots and press the keypad
to the right.
3. Select the desired screenshot. Press MenU.
The screenshot menu will appear.
Files selected on
Utilities list
4. Select Copy and press enTeR. The Copy File
menu will appear.
5. Your MMC/SD card will be listed on the screen. Select your MMC/
SD card and press enTeR. You will be taken back to the list of
screenshots. Repeat Steps 3-5 to copy more screenshots.
Screenshot selected
Screenshot menu
MMC/SD card selected
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Restore Defaults
Toswitchtheunitbacktothesettingsithadwhenyoupurchased
it (default settings), use the Restore Defaults command. Reset
Defaults will reset the unit to default settings.
To Restore Defaults:
1. Highlight Restore Defaults on the System menu and press enTeR. A
confirmation message will appear.
2. Select Yes and press enTeR. The unit will restart.
Advanced
A fine tuning adjustment for advanced users that allows duplicate waypoint names,
enables sticker backlight and slider hold off.
Advanced Settings menu (Enabling Flywheel scroll dial
setting is available only on HDS-8/10-inch units.)
To access Advanced Settings:
1. Select Advanced on the Settings menu and
press enTeR.
2. Highlight a desired setting and use the right/left
arrow keys to open (—) or close (+) the setting.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To adjust Waypoint, Hardware, Flywheel and Radar settings :
1. Open the desired setting (—).
2. Highlight the setting information and
press Enter to turn it on/off. The center
circle will be filled when the setting is
on; empty when it is turned off.
To adjust cursor settings:
1. Highlight the desired cursor setting and press enTeR. A dialog box
will appear.
2. Use the arrow keys to select the desired value and press enTeR.
About
Used to view your unit’s current software version. To check the unit’s software
version, highlight About on the System menu and press enTeR.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Chart Settings Menu
Contains Chart settings ranging from display
options like Range Rings and Grid Lines to map
settings like Chart Data and Datum.
To access the Chart Settings Menu:
1. Press MenU twice.
2. Highlight Chart and press enTeR.
Chart Settings Menu
Chart Data
This unit can use mapping data from Navico and
Navionics. The Chart Data menu allows you to
select the desired map data (Navico 3D mapping
data available in US only).
To select chart data:
1. Highlight Chart Data on the Chart
Settings menu and press enTeR.
The Chart Settings menu
changes when Navionics is
the selected chart data type.
2. Select the desired map data and
press enTeR.
Range Rings
Anavigationaidusedtoestimatedistances.
Centered around your location, Range
Rings are placed a preset distance from
your location, allowing you to quickly
estimate distances while navigating.
To turn Range Rings On/Off, highlight
Range Rings on the Chart Settings menu
and press enTeR.
Range Rings
Heading extension
A line extending from the front of the current position icon that is used to estimate
distance and time of arrival. The distance and estimated time of arrival is based on
the time interval selected from the Heading Extension menu.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Heading Extension line
To use Heading Extension:
1. Highlight Heading Extension from the chart menu and press
enTeR.
2. Select the desired time interval and press enTeR.
NOTE: Range Rings and Heading Extension may not be
available in all chart data.
Popup Information
Turns on information windows that appear when
the cursor is centered on a point of information.
That allows you to identify POIs without having
to zoom in to see it on the screen.
To turn on/off Popup Information, highlight
Popup Information on the Chart Settings menu
and press enTeR.
Gridlines
Grid Lines
Displays base values for latitude and
longitude, making it easier to get a general
idea of your location on the latitude/
longitude scale.
To turn Grid Lines On/Off, select Grid
Lines from the Chart Settings menu and
Press enTeR.
Waypoints
Turns on/off waypoint display properties. When a large number of waypoints are on
the display, turning off waypoints will provide a better view of the map. To turn on/
off waypoint display properties, select Waypoints from the Chart menu and press
enTeR.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Routes
Turns on/off route display properties. When several routes are on the display,
turning off routes will give you a better view
of the map.
To turn on/off route display properties,
select Routes from the Chart menu and press
enTeR.
Trails
Turns on/off Trail display properties. When several trails are on the display, turning
off routes will give you a better view of the map.
To turn on/off trail display properties, select Trails from the Chart menu and press
enTeR.
Hide Chart
Removes mapping data from the display, making it easier
to view routes, waypoints and the cursor.
To turn on/off the map data, highlight Hide Chart on the
Chart Settings menu and press enTeR.
Hide Chart mode
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Sonar Settings Menu
The Sonar Settings Menu is used to modify Sonar
options and display settings like Sonar Source,
Noise Rejection and Fishing Mode.
To access the Sonar Settings:
1. Press MenU twice.
2. Select Sonar and press enTeR.
Sonar Settings Menu
Sonar Source
Selects the display unit that will be used for sonar data. Sonar Source allows you
to view selected transducer data on every display unit on the ethernet network;
even non-sonar units, like the GlobalMap. If you had an ethernet network and two
transducers — one at the bow and one in the back of the boat — you could view
sonar data from either transducer at the helm via the Sonar Source feature.
To select a Sonar Source:
1. Highlight Sonar Source from the Sonar Settings menu and press
enTeR. The Sonar Source menu will appear.
2. Use the keypad to select the desired option and press enTeR.
network Sonar
Allows your unit to send/receive data from another sonar unit on an ethernet network.
To turn on/off network sonar, highlight Network sonar on the Sonar Settings menu
and press enTeR.
noise Rejection
Sonar signal interference from Bilge pumps,
engine vibration, air bubbles, etc., can clutter your
unit’s display. Noise Rejection counteracts sonar
signal interference by reducing onscreen clutter.
To adjust Noise Rejection:
1. Highlight Noise Rejection on the Sonar Settings menu and press
enTeR.
2. Use the keypad to select the desired option and press enTeR.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Surface Clarity
Wave action, boat wakes and temperature
inversion are some of the sources that can
cause onscreen clutter near the surface.
Surface Clarity reduces surface clutter by
decreasing the sensitivity of the receiver
near the surface.
To adjust Surface Clarity:
1. Select Surface Clarity from the
Sonar Settings menu and press
enTeR.
Surface Clutter
2. Use the keypad to choose the desired option.
Scroll Speed
Controls how fast the sonar chart scrolls
across the screen. A slower scroll speed is
best suited for ice fishing or fishing while
at anchor. It is also useful when you want
to record a higher quality sonar log in deep water. By default, Scroll Speed is set to
normal.
To make adjustments, select Scroll Speed from the Sonar Settings menu and use the
keypad to make adjustments.
Manual Mode
Advanced user mode that bypasses digital depth to give you greater control of ping
settings. Digital depth causes the unit to search for the bottom regardless of the
portion of the water column you are targeting. While you still will get good results
using digital depth, it prevents you from getting optimum performance in certain
situations, like fishing for suspended targets.
In Manual Mode the unit sends sonar signals (pings) only to the depth range you
select. Adjustments made to the range setting will be reflected in your unit’s ping
speed. That makes it easy to get the best scrolling speed and the best screen resolution
for a selected range.
Select Manual Mode from the Sonar Settings menu and press enTeR to turn on/
off Manual Mode.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Fishing Modes
Enhances the performance of your unit by providing preset packages of sonar
settings geared to specific fishing conditions.
Settings optimized for fishing modes include: Color Palette, Sensitivity,
Interference Rejection, Surface Clarity and Ping Speed, among others. Fishing
modes allow you to spend more time fishing and less time adjusting settings.
Fishing Mode Options
General Use
Bottom brown/blue background; 50% ping speed
Bottom brown/white background; best suited for
depths less than 100 feet
Shallow Water
Fresh Water
Deep Water
Slow Trolling
Fast Trolling
Clear Water
Brackish Water
Bottom brown/white background; 50% ping speed
Deep Blue; 50% ping speed; 50kHz is primary
transducer frequency
Bottom brown/white background; 50% ping speed
Bottom brown/white background; slightly lower chart
speed
Bottom brown/white background; 50% ping speed
Bottom brown/blue background; higher ASP; slightly
lower chart speed
NOTE: Use Shallow Water Fishing mode when fishing in less
than 100 feet of water.
Shallow Water Fishing Mode
Brackish Water Fishing Mode
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To select a Fishing Mode:
1. Select Fishing Mode from the Sonar Settings menu and press
enTeR.
2. Use the keypad to select the desired mode and press enTeR.
Reset Fishing Mode
Switches Fishing Mode to the default General Use setting. Select Reset Fishing
Mode from the Sonar Settings menu and press enTeR.
Installation Menu
Controls unit settings like Keel Offset, Water
Speed Calibration and Transducer Type only
for components (paddlewheel, temp sensor,
transducer) connected to this display unit
through the blue sonar connector. You can not
adjust settings of network components through
the Installation menu.
To access the Installation menu, highlight
Installation on the Sonar Settings menu and
press enTeR.
Sonar Installation menu
Keel Offset
All transducers measure water depth from the transducer to the bottom. As a result,
water depth readings do not account for the distance from the transducer to the keel
or from the transducer to the water surface. You can use Keel Offset to factor those
distances into the unit’s depth calculations.
Transducer
Keel Offset (-3.5 feet)
Keel
Accounting for the distance from the transducer to the keel will prevent you from
striking underwater objects or running aground, which could damage the keel.
Offsetting the distance from the transducer to the water surface will give you a more
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
precise depth reading.
Before setting keel offset, measure the distance from the transducer to the lowest
part of the keel. If, for example, the keel is 3.5 feet below the transducer, it will be
input as –3.5 feet.
NOTE: To input a keel offset that accounts for the distance
from the transducer to the water surface, you will enter a posi-
tive number. If the transducer is 1.5 feet below the waterline,
it will be input as +1.5 feet. That will give you a more precise
depth reading.
To set Keel Offset:
1. Highlight the Keel Offset text box on the Installation menu and press
enTeR.
2. Use the keypad to enter the desired keel offset. Select OK and press
enTeR.
Water Speed Calibration
When there are differences in speed data, Water Speed Calibration calibrates
data from a paddlewheel with GPS data. That ensures the
accuracy of speed data from your paddlewheel.
To calibrate Water Speed:
Water speed
calibration dialog box
1. Select the Water Speed Calibration text box
from the Installation menu and press enTeR.
The Water Speed Calibration keypad will appear.
2. Use the arrow keys to enter the percentage difference in speed
data. Select OK and press enTeR.
NOTE: If the paddlewheel is reading a slower speed than the
GPS unit, you will input a positive (+) percentage. Conversely,
a negative (–) percentage will be entered if the paddlewheel is
reading a faster speed than the GPS unit.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Water Speed Averaging
Averages water speed by measuring your speed at a selected interval. Water speed
intervals range from one to 30 seconds. If you select five seconds, your water speed
will be recorded every five seconds, then averaged.
To select a Water Averaging interval :
1. Highlight the Water Speed Averaging box on the Installation menu.
2. Press the keypad left/right to select the desired interval.
3. Highlight OK and press enTeR.
Temperature Calibration
When there are differences in temperature data,
Temperature Calibration calibrates data from one
temperature sensor with date from another temperature
source. That ensures the accuracy of temperature data
from the selected temperature sensor.
Water Temp
calibration dialog box
To calibrate Temperature:
1. Select the Temperature Calibration text box from the Installation
menu and press enTeR. The Water Temperature Calibration dialog
box will appear.
2. Use the arrow keys to enter the percentage difference between
temperature sources. Select OK and press enTeR.
NOTE: If the temperature sensor is reading a lower
temperature than the other temperature source, you will input a
positive (+) percentage. Conversely, a negative (–) percentage
will be entered if the temperature sensor is reading a higher
temperature than the other temperature source.
Temperature Averaging
Averages temperature by measuring temperature
data at a selected interval. Temperature intervals
range from one to 30 seconds.
If you select five seconds, your temperature will be averaged using measurements
taken every five seconds.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To select a Temperature Averaging interval:
1. Highlight the Temperature Averaging box on the Installation menu.
2. Press the keypad left/right to select the desired interval and press
enTeR.
Reset Water Distance
If you connect a paddlewheel speed sensor to your unit, you can track the distance
you travel on the water. Reset Water Distance, resets water distance to zero.
To reset water distance, highlight Reset Water Distance and press enTeR.
Transducer Type
Selects the transducer model connected to your display unit. In some transducers
with built-in temperature sensors, the temperature may not be accurate if the correct
transducer is not selected from the Transducer Type menu.
To select a Transducer Type:
1. Highlight Transducer Type box on the
Installation menu and press enTeR.
The Select Transducer menu will
appear.
2. Use the keypad to your transducer
type and press enTeR.
3. Highlight OK and press enTeR.
Transducer type menu
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Radar Settings Menu
Controls Radar options and display settings like Target
Expansion, Orientation and Bearings.
To access the Radar settings menu:
1. Press MenU twice.
2. Select Radar and press enTeR.
Radar Settings
Menu
Target expansion
Increases the size of radar targets, making them easier to see on the radar display. To
turn on/off Target Expansion, highlight Target Expansion and press enTeR.
Target Trails
Creates an onscreen history of the movement
of radar targets, making it easier to monitor
the direction and position of targets in relation
to your vessel.
To set Target Trails:
1. Highlight Target Trails on the
Radar Settings menu and press
enTeR.
2. Use the arrows to select an
Target Trails
interval and press enTeR.
Palette
Radar echoes can be displayed in black, white, green or yellow. The Palette feature
allows you to select the color that suits your viewing preferences.
To change the Palette:
1. Highlight Palette on the Radar Settings menu and press enTeR.
2. Use the keypad to select the desired color palette and press
enTeR.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Black Color Palette
White Color Palette
Orientation
Controls the way the map moves in relation to the movement of your vessel. That
allows you to select a desired method for viewing your surroundings on the radar
display.
•
•
•
Course Up — map stays at same orientation as the initial bearing to the
selected waypoint.
Heading Up — unit keeps your heading at the top of the screen, regardless
of the direction you are traveling.
North Up — North is always shown at the top of the screen.
To change Map Orientation:
1. Highlight Map Orientation on the Radar
Settings menu and press enTeR.
2. Use the keypad to select the desired
option and press enTeR.
Threshold
Controls the level of radar returns. That allows you to unclutter the display by
removing unwanted signals.The zero percent setting allows all To make adjustments,
select Threshold and press the keypad left/right.
north Indicator
The North indicator is shown on the outer circle of the radar display. To turn on/
off North Indicator, select North Indicator from the Radar Settings menu and press
enTeR.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Range Rings
Allows you to quickly estimate the distance
from your vessel to a another radar target.
To turn on/off Range Rings, highlight Range
Rings on the Radar Settings menu and press
enTeR.
Range rings
Range markers
Range Markers
Located below each Range Ring, Range
Markers display the distance from your position
to each range ring.
To turn on/off Range Markers, select Range
Markers from the Radar Settings menu and
press enTeR.
Compass
A Compass overlay can be displayed on the background of the radar page. To turn
on/off the Compass overlay, select Compass and press enTeR.
Compass Overlay turned off
Compass Overlay turned on
Bearings
Bearings allows you to choose if you want the direction you are headed to show
as True Magnetic (TM) or Relative (R). T/M or True/Magnetic will show your
direction based on magnetic north. R or Relative will show your direction based on
your relative heading.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To set T/M or R:
1. Press MenU twice.
2. Select Radar and press enTeR.
3. Highlight Bearings and press enTeR.
4. Use the arrows to select a bearing and press enTeR.
Installation
Provides access to the Radar Installation menu.
Radar Installation menu
To access Radar Installation menu:
1. Press the MenU key twice.
2. Highlight Radar and press ENTER.
3. Select Installation and press enTeR.
Installation Adjustment Menu
The installation adjustment menu is used to make adjustments to bearing alignment,
range offset, antenna height and open array park angle.
When the installation adjustment menu is accessed, press the
keypad up/down to select a feature. Press the keypad left/right
to make adjustments to a selected feature.
Press exIT to return to the Radar Installation menu. To remove
the Radar Installation menu from the screen, select Close and
Adjustment Menu
press enTeR.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Bearing alignment
Used to align the bow of your vessel with the heading line (zero point). Bearing
alignment is also referred to as zero bearing.
To make adjustments to bearing alignment, switch the radar state to Transmit and set
radar orientation to Heading Up.
To select Heading up orientation:
1. From the Radar Page, press MenU.
2. Select Orientation and press enTeR.
3. Use the keypad to select Heading Up and press enTeR.
4. Press exIT.
After Bearing Alignment
Before Bearing Alignment
Bearing line aligned with
peninsula, matching the
alignment of the bow.
Bow of ship is lined up with
the tip of a peninsula; the
bearing line is not.
To Adjust Bearing Alignment:
1. Line up the bow of your vessel with a stationary target (lighthouse,
pier, etc) at least 1 nm away
2. Select Adjust Bearing Alignment from the Radar Installation menu
and press enTeR. The Installation Adjustment menu will appear.
3. Press the keypad left/right to rotate the radar image so the reference
target is at 0° or 12 o’clock from the radar center.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Range offset
Eliminates the time lag between real radar returns and the time it takes data to be
processed by the radar software. Range Offset is also referred to as zero range and
trigger delay.
Range Offset Sequence. The circle shrinks as range is increased.
To Adjust Range Offset:
1. Use the ZOOM In/ ZOOM OUT keys to set range to 1/8 nm.
2. Highlight Adjust range offset from the Radar Installation menu and
press enTeR. The installation adjustment menu
will appear.
3. Press the keypad to the left set range offset to 0.
Press enTeR.
4. If there is a blank, black circle around the center or
a solid circle of color at the center, increase the range offset until the
circle disappears or almost disappears.
5. If you increase th range offset too far, decrease it until the circle
appears again.
Antenna Height
Antenna height is the distance from the waterline to the Antenna (scanner). It is
important to correctly input antenna height to prevent problems with the Sea Clutter
feature.
To Adjust Antenna Height:
1. Select Adjust Antenna Height from the Installation menu and press
enTeR.
2. Press the keypad left/right to input the distance from the antenna to
the water surface. Press exIT.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Open Array Park Angle
When an open array antenna is turned off, the antenna’s momentum will cause it
to continue rotating before coming to a stop. Open array park angle allows you to
adjust the antenna’s parking angle so it will stop in a desired position.
To Adjust Open Array Park Angle:
1. Select Adjust Bearing Alignment from the Radar
Installation menu and press enTeR. The
Installation Adjustment menu will appear.
2. Press the keypad left/right to enter a value that will
cause the antenna to stop in the desired position.
Tune
You should not have to adjust Tune for the life of this unit. This feature is intended
for use by only trained technicians.
Reset Radar to Factory Defaults
Resets radar to factory default settings.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Fuel
Used to input fuel data like engine/tank configuration,
fuel tank capacity and engine calibration. Your unit uses
that data to calculate the overall fuel performance of your
vessel. To access the Fuel menu, select Fuel from the
Settings menu and press enTeR.
Fuel menu
Refuel
Controls engine calibration and is used to input the amount of fuel added to the
tank(s). Engines must be calibrated with your fuel tanks to get correct readings on
fuel economy, fuel used, etc.
Amount Added
window
Set to Full
Amount
checkbox: Check
this box when you
fill up your tank
Added text
box: Input
amount of fuel
added here
Refuel menu
It is important to enter the amount of fuel added to your tank(s) each time fuel
is added. That ensures the correct fuel data is used in the unit’s fuel performance
calculations.
To input fuel added:
1. Select Refuel from the Fuel menu and press enTeR.
2. Use keypad to select the Amount Added window and press enter.
The Amount Added text box will appear.
3. Use the keypad to input the amount of fuel added and press
enTeR.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To set tank to full:
1. Highlight the Set to full checkbox
on the Refuel screen and press
enTeR.
2. Highlight OK and press enTeR.
The calibration options screen will
appear. You are
ready to calibrate.
Tank set to full
To calibrate engine(s):
1. With the calibration options screen displayed, select the checkbox
next to the engine you would like to calibrate .
2. Highlight OK and press enTeR. The Calibration screen will
appear.
Calibration screen
Calibration options screen
3. Use the keypad to highlight the Actual amount used window and
press enTeR.
4. Input the amount of fuel used in the Actual amount used dialog box
and press enTeR.
5. Highlight the Next button and press enTeR. The Confirm calibration
screen will appear.
6. After confirming calibration data, highlight OK and press enTeR.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Fuel Used
Data information screen that displays fuel
consumption data including fuel used
since last fill up, fuel used on the current
trip and fuel used during a season.
To access fuel used information, select
Fuel Used from the Fuel menu and press
enTeR.
Highlight the Reset button and press
enTeR to set corresponding fuel data
values (trip and seasonal) to zero.
Fuel used screen
Vessel Setup
Controls vessel configuration, which includes selecting the number of engines/
fuel tanks and inputting the capacity of each fuel tank. Vessel Setup data must be
configured before you can calibrate your engine(s).
To access the Vessel Setup menu, highlight Vessel Setup on the Fuel menu and press
enTeR.
Tank size text
box: input
tank size here
Vessel
configuration
menu: select
number of
engines and fuel
tanks here
Tank size
window
Calibration
info button: get
calibration info
here
Vessel Setup
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Engine/Tank Configuration
Used to input the number of engines and fuel tanks on your vessel. Your unit must
have that information to be able to calibrate you engine(s).
To select engine-tank configuration:
1. Highlight the vessel configuration drop-down
menu and press enTeR.
2. Select a engine/tank configuration and press
enTeR.
3. Highlight the Save button and press enTeR.
To input tank size:
1. Highlight the Tank Size window and press enTeR. The Tank Size
Text box will appear.
2. Use the keypad to input the size of the
selected tank and press enTeR.
3. Repeat Step 2 for each tank on your
vessel.
4. Select the Save button and press
enTeR.
Calibrate
Launches engine calibration information window
referring you to your fuel sensor’s installation
manual.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Alarms
This unit has alarms covering everything from depth and water temp rate to fuel and
waypoint radius. The alarms list has three tabs: Active, History and Settings.
•
•
Active — used to view alarms that have been enabled
History — shows log of alarm activity, which includes data like when
alarms were triggered and when they were cleared
•
Settings — provides access to Alarms list, allowing you to enable
alarms and set alarm limits
NOTE: Some alarms will not work unless a corresponding
sensor is connected to the unit or the network.
To enable/disable an Alarm:
1. Select Alarms from the Settings menu and press enTeR.
2. Highlight Settings and press enTeR.
3. Select the desired alarm from the alarms list and press enTeR.
Enable alarms and set
limits (thresholds)
Displays list of
enabled alarms
Shows history of
alarm activity
Enabled
Alarm
Alarms List
Alarm Limits (Thresholds)
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To silence an alarm:
When an Alarm is triggered, a tone will sound and a alarm window will appear on
the screen. Press enTeR to silence the alarm and close the alarm window.
After alarm is silenced its corresponding alarm bell will continue to flash
in the bottom left corner of the screen. To remove the bell from the screen,
disable the alarm and then enable it again. The bell will not reappear unless
the alarm is triggered.
Set Limit
Sets thresholds (limits) that will trigger the alarm when met or exceeded. If a
threshold can be set for a particular alarm, the Set Limit button will appear at the
bottom of the screen when that alarm is highlighted on the alarm list.
To set alarm limit:
1. Highlight the desired alarm on the alarm
screen and press MenU.
2. Select Set Limit and press enTeR. The
Alarm Limit keypad will appear.
3. Input the desired alarm threshold and
Set limit selected on Water
press enTeR.
Temp Rate menu
Siren enabled
When the Siren is enabled, a tone will sound when an
alarm is triggered. To enable alarm sirens, highlight
Siren Enabled on the Alarms menu and press
enTeR.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Trails
Controls the way trails are logged (updated).
Trails mark your movement as you travel,
placing points along your path using one of
three logging types: Time, Distance or Auto.
You can save up to 10 trails with up to 9,999
points per trail. If a trail exceeds 9,999 points,
each new point will overwrite a point at the
beginning of the trail.
Trails Menu
Logging Type
Controls the method used for updating a trail. Trails can be updated using Time,
Distance or the default automatic setting.
Logging Types
A point is placed along the trail after a selected amount of time
A point is placed along the trail after you travel a selected distance
A point is placed along the trail every time you change direction
Time
Distance
Auto
To select a Logging Type:
1. Highlight Logging Type on the Trails menu and press enTeR.
2. Use the keypad to select Auto, Distance or Time and press enTeR.
Distance Period
Controls how far you will travel before a point is placed along the trail.
To set Distance period:
1. Highlight Distance Period and press
enTeR. The distance period keypad
will appear.
2. Input the desired distance and select
OK. Press enTeR.
Distance Period set to 1nm
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Time Period
Controls how much time will pass before a point is placed along the trail.
To set Time Period:
1. Highlight Time Period and press
enTeR. The distance period keypad
will appear.
2. Input the desired distance and select
OK. Press enTeR.
Time Period set to 5 seconds
Units
Controls the unit of measure used for a variety of
data, ranging from distance and speed to heading and
barometric pressure. To access the Units menu, select
Units from the Settings menu and press enTeR.
To change a unit of measure:
1. Select a unit from the Units menu. Press
enTeR.
2. Select the a unit of measure and press
enTeR.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Network
Controls network configuration, data sources, serial port
settings, waypoint sharing and allows you to monitor
network performance (NMEA 2000 and ethernet) and
network devices.
To access the Network menu, select Network from the
Settings menu and press enTeR.
Network menu
Auto Configure
Resets all Data Sources to default settings
and removes all instances on networked
HDS units.
To auto configure a network:
1. Select Auto Configure from the Network menu and press enTeR.
2. Highlight Yes and press enTeR.
Data Sources
An advanced feature that allows you to use
data from a network data source or data from a
sensor connected to your unit.
If, for example, you do not want to use your
unit’s internal GPS antenna, you could use an
external GPS antenna connected to an ethernet
or NMEA 2000 network.
To access the Data Source Selection Screen,
highlight Data Sources on the Network menu
and press enTeR.
Data Source Selection Screen
To select a data source:
1. Select a data category and press the keypad to the right. A subcategory list
will appear.
2. Select a subcategory and press the keypad to the right. A list of sources will
be displayed.
3. Highlight a desired data source and press enTeR.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Data Source menu
Allows you to change the name and scope of a source and add/remove sources
from a NMEA 2000 or ethernet network. To access a Data Source menu, highlight
a desired source and press MenU.
Rename
Used to rename a Data Source. That makes it easier to recognize one
data source from another when they are the same type of source.
To Rename a data source:
1. Select Rename from the desired data source menu and
Data Source
press enTeR. A keyboard will appear.
menu
2. Input the desired name and select OK and press enTeR.
New
Allows you to create a new instance of a data source.
To create new data source instance:
1. Select New from the desired source menu and press enTeR. A keyboard
will appear.
2. Input the name of the new instance, select OK and press enTeR.
Remove
Removes an instance from the Data Source Selection list.
To remove an instance, select Remove from the desired data source menu and press
enTeR. The data source is removed from the Data Source Select list.
Scope
Controls the way data source settings are shared/not shared on an ethernet network.
Scope lets you select a mode that allows data source settings to be shared by HDS
units on an ethernet network (Global).
You can also select a mode that allows each HDS unit to have individual data source
settings (Local).
Scope Settings
Global
Local
Data source settings will apply to all Data source setting will apply only
HDS units on an ethernet network. to the unit with the local setting.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To select a scope:
1. Highlight Scope on the selected device’s data source menu and
press enTeR.
2. Use the keypad to select Global or Local and press enTeR.
Reset Global and Reset Local
Selecting Reset Global will reset all the source selections to default settings and
removes all instances on all networked HDS units.
Reset Local is used to change all source selections on your HDS unit from Local to
Global.
To reset global or local sources:
1. Highlight Resset Global or Reset Local and press enter. A confirmation
message will appear.
2. Select Yes and press enter.
Device List
Displays a list of devices connected to a NMEA 2000 network.
From the Device List you can:
•
•
•
•
•
•
View device data
Change the device instance
Configure device alarms
Configure devices
Calibrate devices
Device List
Enable/disableWAAS/EGNOS/MSASforGPSantennabyconfiguring
HDS iGPS
To access the device list, Select Device List from the Network menu and press
enTeR.
Device Menu
Controls the way data is displayed on the Device list. To
access the Device menu, highlight the desired device and press
MenU.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Device Menu Options
Details
Accesses the Device Information screen
Refresh Refreshes the device list
Sort
Allows you to sort device list by Model ID or Serial No.
Configuring Devices
Devices have different configuration options. Name, tank size and location can
be configured on some devices; only the name can be configured on others. Some
devices like a fuel flow, can be calibrated from the device list.
Device List
Device Information
Screen
Device Configuration
Screen
To configure a device name or device tank size:
1. Select a device from the device list and press enTeR. The Device
Information screen will appear.
2. Highlight the Configure button and press enTeR. The Device
Configuration screen will appear.
3. Highlight the Name or Tank Size text box and press enTeR. A keypad
will appear.
4. Use keypad to input the desired information. Select OK and press
enTeR.
NOTE: For more information on device configuration refer to the
documentation that came with your device.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
To configure device location:
1. Select a device from the device list and press enTeR. The Device
Information screen will appear.
2. Highlight the Configure button and press enTeR. The Device
Configuration screen will appear.
3. Highlight the Location dropdown menu and press enTeR.
4. Select the desired location and press enTeR.
Instance
You can change a device instance from the Device Configuration screen. This,
however, should only be attempted by a qualified technician.
Calibrating devices
Several devices can be calibrated from the devices list including Fluid Levels, Fuel
Flows and Trim Tabs. Every device that can be calibrated from the devices list, will
have a calibrate button on the Device Information screen. The calibrate button opens
the Device Calibration screen, which has onscreen calibration instructions for the
device.
Calibration instructions for a
Calibrate button
fluid level
To access calibration instructions:
1. Select the desired device from the device list and press enTeR.
2. Highlight the Calibrate button on the Device Information screen and
press enTeR. Follow the onscreen calibration instructions.
NOTE: For more information on device calibration, refer to
the documentation that came with your device.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Diagnostics screen: UDB
Diagnostics screen: NMEA 2000
Diagnostics
Displays diagnostic information on NMEA 2000 networks displays the status of
information shared between units (UDB). From the UDB tab, you also can select a
unit to be used as the master (primary) unit when sharing information.
To access the Diagnostics screen, select Diagnostics from the Network menu and
press enTeR.
NMEA 2000 receive/send waypoint
Turnson/offtheunit’sabilitytosendandreceive
waypoints across a NMEA 2000 network.
NMEA 0183 receive waypoint controls the
unit’s ability to receive waypoints over a
NMEA 0183 network.
NMEA 2000 receive waypoint
turned on
To turn on/off NMEA send/receive waypoint commands, highlight the desired
NMEA send/receive option and press enTeR.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Serial Ports
Configures communication ports to send or receive data with another electronic
device, like an autopilot.
To configure serial ports:
1. Highlight Serial Ports on the Network menu
and press enTeR. The Serial Settings
menu will appear.
2. Select the desired setting (Protocol,
Communication Port 1 or Communication
Port 2) and press enTeR.
Serial settings menu
3. Use the keypad to select the desired option
and press enTeR.
4. Highlight OK and press enTeR.
NMEA 0183 Output
Controls NMEA 0183 sentences used, allowing you to select the type of messages
your unit will transmit when communicating with other NMEA 0183 devices. The
default setting will work well under most conditions.
To access NMEA 0183 Output screen:
1. Select NMEA 0183 Output from the
Network menu and press enTeR.
2. Highlight a desired sentence and press
enTeR to turn it on/off.
3. To finalize changes, select OK and
press enTeR.
NMEA 0183 Output screen
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Vessels
Controls settings used to monitor vessels in your
area with an AIS receiver. The Vessels feature
makes it easier to navigate safely through high
traffic areas.
Vessels Menu
To access the Vessels menu, select Vessels from the
Settings menu and press enTeR.
MMSI (Maritime Mobile Service Identity)
Used to input your MMSI number into the unit.
To input MMSI number:
1. Highlight MMSI on the Vessels menu
and press enTeR.
2. Use the keypad to input the MMSI
number and press enTeR.
Display
Allow you to select what vessels will be shown on the display. That helps you
customize the screen so you can view only desired vessels.
Display options
All
Displays all vessels in the area around your vessel
Eliminates all vessels from the display
None
Moving
Displays vessels that are in motion
Show only vessels that likely will be coming into close
Dangerous proximity of your vessel; based on CPA (Closest point of
approach) and TCPA (Time to closest point of approach)
To select a Display option:
1. Select Show on the Vessels menu and press enTeR.
2. Use the keypad to select the desired display setting and press
enTeR.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Course Extension
A line extending from each vessel on the chart screen
used to estimate where a vessel will be in a selected
amount of time, if it maintains its current course.
Course Extension
To use Course Extension:
1. Select Course Extension from the Vessels menu and press enTeR.
2. Select the desired duration (1, 2, 10, 30, 60 or 120 minutes) and
press enTeR.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Simulator
Accesses all simulation types including default
demo and simulator modes as well as advanced
custom simulations.
To access the Simulator menu, highlight Simulator
on the Settings menu and press enTeR.
Simulator menu
Simulate
Turns on/off your unit’s simulator. Simulate must be turned on to view a simulation,
whether you are using the default mode or a custom simulation.
To turn on the simulator, select Simulate from the Simulator menu and press
enTeR.
Demo Mode
Rotates simulations from each of the unit’s operation modes with screens detailing
some of the unit’s most popular features.
To choose a Demo Mode:
1. Highlight Demo Mode from the Simulator menu and press enTeR.
2. Use the keypad to select the desired mode and press enTeR.
Advanced
Allows you to set up a customized simulation
using sonar, GPS, radar and weather data files
(where applicable).
To access the Advanced menu, select Advanced
from the Simulator menu and press enTeR.
Advanced Simulator menu
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Source Files
Controls source files used in radar, sonar,
AIS (Chart) and Weather simulations.
Source files allow you to use your own data
while running a simulation.
To select a source file:
Source File menu
1. Highlight the desired source file option on the Advanced menu and press
enTeR.
2. Use the keypad to select a source file and press enTeR.
GPS Source
Selects the data source that will be used in a GPS simulation. That allows you to use
navigation data from sonar, radar, simulated course or simulated routes as GPS data
during a simulation.
To select a GPS Source:
1. Select GPS Source from the Advanced
menu and press enTeR.
2. Use the keypad to select the desired
source and press enTeR.
GPS Source menu
Speed and Course
Allows you to select the speed and course to be used during a simulation.
To input Speed and Course
1. Select Speed or Course from the Advanced menu
and press enTeR.
2. Use the keypad to input the desired value and press
enTeR.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Route
Allows you to select a route to be used
during a simulation.
To select a route:
1. Select Route from the Advanced menu and press enTeR. A Route List
will appear.
2. Use the keypad to select the desired route and press enTeR.
Set Start Position
Sets the starting point of a GPS Simulation to the cursor position.
To set start position:
1. Highlight the Set Start Position button on the Advanced menu and
press enTeR.
2. Select the Set button and press enTeR.
3. Highlight OK and press enTeR.
Restore Defaults
Switches Advanced simulator options back to defaults settings. To restore defaults,
select Restore Defaults from the Advanced menu and press enTeR.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Unit Care
Specifications
GeneRAL
Depth capability: 5,000 ft dependent on
transducer configuration and installation, bot-
tom composition and water conditions
Case Size:
• HDS-5: 5.8” H x 7.3” W x 4” D (14.6 x 18.4 x
10.2 cm), 2.30 lbs
Built-in sonar recording capacity: 10min to
2hrs internal memory depending on depth
range and ping speed
• HDS-7: 6.4” H x 8.8” W x 3.5” D (16.3 x 22.4
x 8.8 cm), 3.10 lbs
Display:
• HDS-5: 5.0” (12.7 cm) diagonal high contrast
16-bit color TFT, 480 x 480 pixel resolution
• HDS-7: 6.4” (16.3 cm) diagonal high contrast
16-bit color TFT, 640 x 480 pixel resolution
Surface water temperature: Available built
into transducer or via external network
Paddlewheel speed log: Available with
optional speed sensor
Backlighting:
• HDS-5: Florescent (CCFL) backlit screen,
LED keypad backlight
Audible alarms: Shallow, Deep, Tempera-
ture change
• HDS-7: LED backlit screen and keypad
Supply voltage: 10 to 18 volts DC
GPS nAVIGATIOn
Supply current:
• HDS-5: 0.7A at 13VDC with backlight on,
0.4A with backlight off
• HDS-7: 0.8A at 13VDC with backlight on,
0.4A with backlight off
Receiver/antenna:
• Built in 16 parallel channel internal antenna
• External antennas supported via NMEA
0183 and NMEA 2000
Satellite DGPS: WAAS, EGNOS, MSAS
supported
Operating temperature: -15°C to 55°C (5°F
to 130°F)
Compass Safe Distance: 20cm (8 inches)
MMC slots: Two with waterproof doors. One
reads SD, MMC, and MMC+. One reads SD
and MMC.
Charting: Contains built-in Lowrance or
Navionics basemap; Lowrance map and
chart range, Navionics Gold, Platinum, and
Platinum Plus supported via SD/MMC card
Audible alarms: Local and networked
alarms available for included and optional
components, including sonar, GPS/naviga-
tion, battery voltage, weather, engine/trans-
mission, tank level, AIS and DSC.
Position updates: Every second with inter-
nal antenna
Chart scale: 50ft (20m) to 2,500 nautical
Communications: NMEA 0183 input and
output up to 38,400 baud, NMEA 2000,
Navico Ethernet
miles (3,000 miles)
Built-in GPS recording capacity: 32MB
internal memory capacity for up to 5,000
user-definable waypoints, 10 tracks, and 200
routes
Standards compliance:
• Waterproofing: IPX6 and IPX7 with card
door closed
• EMC: IC RSS-310; FCC Part 15 Class B;
IEC60945
Audible alarms: Arrival, off-course, anchor
NOTE: The above memory ca-
pacities refer only the unit’s
on-board memory. The amount
of GPS and sonar data you can
record and save for recall later
is only limited by the number of
MMC cards you have.
BROADBAnD SOUnDeR
Frequency: 50/200 kHz or 83/200 kHz
Power output: 250W Peak to Peak (31W
RMS) actual, 30,000W Peak to Peak analog
equivalent
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Unit Care
Display
•
Cleaning the Screen — Warm water and soap will work fine. You
can also use ammonia-type cleaners like Windex. Do not use any type of
abrasive cleaners. They will remove the Anti-Reflection coating from the
glass.
Buttons
•
•
Inspect the buttons — Make sure that no buttons are stuck in
the down position. If one is stuck, wiggle the button to free it back to the
normal position.
Debris in the keyboard contacts — In case there is dirt or
other debris covering the contacts inside the keypad, press down on the
button in question and wiggle it to try to restore its function.
Connectors
• Clean the Connections — Corrosion or oxidation could occur on
the power cable connector pins and fuse-holder. This can prevent sufficient
power from flowing to the unit. Clean the connections to be sure. Some-
times the substance is clear and not easily seen.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
If your unit is not working, or if you need technical help, use the following
troubleshooting section before contacting the customer service department.
Unit won’t turn on
1.
2.
Check the power cable’s connection at the unit.
Make sure the power cable is wired properly. The red wire
connects to the positive battery terminal, black to negative
or ground.
3.
4.
Check the fuse.
Measure the battery voltage at the unit’s power connector.
You will measure the two biggest pins. It should be at least
10 volts. If it isn’t, the wiring to the unit is defective, the bat-
tery terminals or wiring on the terminals are corroded, or the
battery needs charging.
Unit freezes, locks up, or operates erratically
1.
Electrical noise from the boat’s motor, trolling motor, or an
accessory may be interfering with the sonar unit. Rerouting
the power and transducer cables away from other electrical
wiring on the boat may help. Route the sonar unit’s power
cable directly to the battery instead of through a fuse block
or ignition switch.
2.
3.
Inspect the transducer cable for breaks, cuts, or pinched
wires.
Check the transducer and power connector. Make sure it’s
securely plugged into the unit.
Weak bottom echo, erratic readings or no fish returns
1.
2.
Make sure the transducer is pointing straight down like the
following image.
If the transducer is mounted inside the hull, be sure it is
shooting through only one layer of fiberglass, that it is
securely bonded to the hull and DOES NOT have air
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
bubbles. (See the Installation Section for how to install the
transducer.)
3.
4.
When attaching a transducer to the inside of a hull, ONLY
use epoxy available from LEI (see inside back cover for or-
der information).
Do NOT use RTV silicone rubber adhesive or any other type
of epoxy. The LEI epoxy is specially formulated so that it will
cure properly for shoot-through applications.
5.
6.
Clean the face of the transducer. Oil, dirt and fuel can cause
a film to form on the transducer, reducing its effectiveness.
Electrical noise from the boat’s motor or trolling motor can
interfere with the sonar. This causes the sonar to automati-
cally increase its discrimination or noise rejection feature.
This can cause the unit to eliminate weaker signals such as
fish and can display lines across the screen.
7.
The water may be deeper than the sonar’s ability to find the
bottom. If the sonar can’t find the bottom signal while it’s in
the automatic mode, the digital sonar display will flash con-
tinuously. It may change the range to limits far greater than
the water you are in. If this happens, place the unit in the
manual mode, then change the range to a realistic one, (for
example, 0-100 feet) and increase the sensitivity. As you
move into shallower water, a bottom signal should appear.
8.
Check the battery voltage. If the voltage drops, the unit’s
transmitter power also drops, reducing its ability to find the
bottom or targets.
Bottom echo disappears at high speeds, erratic reading
or weak bottom echo while boat is moving
1.
This is likely due to cavitation (turbulence) in the water sur-
rounding the transducer. You may need to move the trans-
ducer lower in the water or to another location. The trans-
ducer cannot send or receive signals through air bubbles.
2.
Electrical noise from the boat’s motor or trolling motor
can interfere with the sonar. This causes the sonar to
automatically increase its discrimination or noise rejection
feature. This can cause the unit to eliminate weaker signals
such as fish or even structures from the display. Try using
resistor spark plugs or routing the sonar unit’s power and
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
transducer cables away from other electrical wiring on the
boat.
3.
When trolling over weed beds in 20ft of water or less, you
may experience vertical bars, loss of the chart picture, or
the digital depth. First, do a soft reset of the unit. Then go
to the Full Sonar Chart screen. Press Menu and select So-
nar Features. Now turn the Chart Manual Mode to On. This
will leave everything in Automatic Mode except depth. Now
go back to the main menu and set the depth range for the
depth you are in such as 0-20 feet.
4.
5.
It can sometimes be difficult for a high-powered unit to cap-
ture the lightning-fast return in shallow water. Turn off the
automatic sensitivity setting and manually reduce the sensi-
tivity until the unit locks onto the bottom.
If two or more sonar units using the same frequency are op-
erating at the same time, one or more of them may lose the
depth reading due to the interference. It is like two radio sta-
tions trying to both broadcast on 97.3FM. In shallow water,
if the transducers are far enough apart, you may be able to
operate them together. However, the deeper the water, the
wider the beams spread out. When they cross each other,
the interference occurs.
No fish arches when Fish I.D. is turned off
1.
If you are using a transom-mounted transducer, the angle
of the transducer may prevent a fish arch from displaying
properly. If the arch slopes up but not down, then the front of
the transducer is too high and needs to be lowered. If only
the back half of the arch is shown, the nose of the trans-
ducer is angled too low and needs to be raised. This is the
most common problem if a partial arch is displayed.
2.
3.
The sensitivity may not be high enough. For the unit to dis-
play a fish arch, it has to be able to receive the fish’s echo
from the time it enters the cone until it leaves. If the sensitiv-
ity is not high enough, the unit shows the fish only when it is
in the center of the cone.
Use the Zoom feature. It is much easier to display fish arch-
es when zoomed in on a small range of water than a large
one. If your boat is in water deeper than 20ft, try setting the
upper and lower limits to a 20ft depth section, such as 40ft
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
to 60ft or whatever depth you expect the fish to appear at.
This will maximize the screen resolution to show small ob-
jects larger on the screen. It unlikely you will see average-
sized fish display as arches in a 100ft deep water column.
4.
The boat must be moving at a slow trolling speed to see
fish arches. If the boat is motionless, fish stay in the cone
and show as horizontal lines on screen. This is especially
applicable to ice fishing.
noise
1.
A major cause of sonar problems is electrical noise. This
usually appears on the sonar’s display as random patterns
of dots or lines. In severe cases, it can completely cover the
screen with black dots, or cause the unit to operate errati-
cally, or not at all.
2.
3.
4.
To eliminate or minimize the effects of electrical noise,
try to determine the cause. With the boat at rest in
the water, turn all electrical equipment on the boat
off including the engine. Turn on your sonar unit.
Sensitivity should be set at 70-75 percent. There should be
a steady bottom signal on the display. Now turn on each
piece of electrical equipment on the boat and view the effect
on the sonar’s display.
If you find noise interference is from an electrical instru-
ment, trolling motor, pump, or radio, you can usually reroute
the sonar unit’s power cable and transducer cable away
from the wiring causing the interference. VHF radio antenna
cables radiate noise when transmitting, so be sure to keep
the sonar’s wires away from it. You may need to route the
sonar unit’s power cable directly to the battery to isolate it
from other wiring on the boat.
If no noise displays on the sonar unit from electrical equip-
ment, then make sure everything except the sonar unit is
turned off, then start the engine. Increase the RPM with
the gearshift in neutral. If noise appears on the display, the
problem could be one of three things; spark plugs, alterna-
tor, or tachometer wiring. Try using resistor spark plugs, al-
ternator filters, or routing the sonar unit’s power cable away
from engine wiring to help eliminate noise problems. Make
sure to use the in-line fuse supplied with the unit when wir-
ing the power cable to the battery.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
5.
When no noise appears on the sonar unit after all of the
above tests, then the noise source is probably cavitation.
Many people make sonar installations which function per-
fectly in shallow water, or when the boat is at rest. In most
cases, the cause of the malfunction is the location and/or
angle of the transducer. The face of the transducer must be
placed in a location that has a smooth flow of water at all
boat speeds. Read your transducer owner’s manual or the
Installation instructions in this manual for the best mounting
position.
GPS not Accurate
1.
Lowrance Electronics obtains its mapping data from gov-
ernment agencies. Mapping is not an exact science. A unit’s
GPS position (Latitude/Longitude) can be extremely accu-
rate, but the location of a cartographic item such as a street,
highway, or point-of-interest may be slightly inaccurate. In
most cases, we have found the mapping detail in our prod-
ucts to be very accurate. We encourage the reporting of
inaccuracies or omissions so that we can consider them
for future revisions. Please consider that our products are
designed to be aids to navigation and not the sole means of
navigation. A prudent navigator will also have several items
necessary for safe navigation.
2.
3.
The accuracy of your position could look different at various
zoom ranges. For example, at a 5 mile range, the cursor
representing your position may appear to be in the center
of a highway your are driving on. However, if you zoom into
a much closer .1 mile range, the position may appear off-
center due to the variables mentioned above.
Try this simple method to verify that the GPS receiver in
your unit is accurate. Have your unit lock onto GPS position
in a known location like your driveway, boat slip, or camp-
site. Save that location in the unit as a waypoint. Now trav-
el away from the known location. Stop and recall the saved
waypoint in the unit. Select GO TO to start the unit navigat-
ing back to that location. Observe the Distance To Go data
as you travel back to that location. When you arrive at your
waypoint, the Distance To Go should be close to 0.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Cards not Read by Unit
1.
Before purchasing a pre-loaded mapping card for a unit,
go to our Mapping Index at http://www.lowrance.com/Prod-
ucts/Mapping/default.asp Click on the type of card you are
interested in and look at the list of units that are compatible
with that card.
2.
3.
When zooming in to see more detail, be sure the cursor is
located within the area covered by the mapping card.
In the Chart menu, select Chart Options and then Chart
Categories. Make sure all the categories you want to see
have a check mark beside them.
4.
5.
If the card is not recognized by the unit, make sure the card
contacts and corresponding unit pins are clean and free of
obstructions. Verify that the card is securely seated in the
card port.
If it is a card for a MapCreate map or saved GPS data, it
may need to be formatted. Do not format pre-loaded cards
such as Nautic-Path, Fishing Hot Spots Pro, Lake Master
Pro, Freedom Maps, or Navionics. The information will be
deleted from the card. Please be aware that Lowrance GPS
products will only read cards that are FAT formatted. MMC
cards formatted using FAT 32 or NTFS will not work with
our products.
Current Position not on the Screen
1.
First, make sure the unit is locked onto the satellites and
shows a fix on the satellite status screen. Then check for
cross-hairs on the screen (or for an automotive unit, a red
box with an X). If this is on the screen, it means that you had
pressed one of the arrow buttons. If that is the case, the unit
thinks that you want to scroll to a location on the screen or
zoom in or out to see more detail. Press the EXIT button to
clear the crosshairs and your current position will show in
the middle of the display.
2.
To determine your current position, the GPS receiver must
“lock” onto at least 3 GPS satellites. For the best signal re-
ception, an external GPS antenna/receiver should be locat-
ed where it can receive as many signals as possible. There
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
should be nothing around or above the antenna. However,
GPS antennas can receive signals well through many types
of glass and fabric. It is recommended to try various loca-
tions before making a permanent installation.
3.
If you are using a NMEA2000 network, both branches of the
power cable with red and black wires need to be connected
to a 12volt power source. Be sure all cable connections are
clean and solid. Check to be sure power is reaching the
GPS receiver. Also, check the power to the blue connector
network and the red connector network.
Update the Software
Make sure your unit has the latest software version. Go to the Software
Update page on Lowrance.com. You can download updates for free.
Reset the Unit
Sometimes resetting your unit can solve unusual issues. Go to Lowrance.
com to access a list of reset procedures for Lowrance products. Locate the
one that applies to the model you own. Try a Soft Reset first, this will return
your settings to factory defaults. If you decide to try a Hard Reset, save
any important stored data to an MMC or SD card or write the information
down. The data will be deleted during this process.
Radar won’t Start Up
If the radar, does not start up, try the following steps:
1.
2.
3.
Verify head unit has the latest code that supports radar.
Verify that the communication port is set to RADAR
Turn the unit, radar and network off, then turn everything
back on. On power up the Radar should start initializing.
Change over to the Radar Page and see if the unit is initial-
izing or giving the count down indication.
a. If you are getting a countdown: allow it to complete and
then try to power on the Radar. If the Radar does not
start rotating then the Radar will need to be sent in for
service.
b. If you are NOT getting a countdown, press MENU, se-
lect RADAR INFORMATION and press ENT.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Highlight FORCE STATUS UPDATE and press ENT.
Pay attention to the RX/TX buttons.
c. If the TX is not lighting up then either you do not have
the com port set to RADAR or the GPS unit is defective.
Verify that the Com Port is set properly, if it is then the
Lowrance unit will need to be sent in for repair.
d. If the TX is blinking but the RX is not then you are not
getting any information from the RIM, the processor or
the Radar. There is a fuse inside the processor that
has more than likely blown. Remove the front left black
screw, then remove the grounding post on the right side
of the front of the unit. Gently slide the front cover off,
the fuse is located on the left side of the board. This
fuse is very tight and difficult to remove, you may need
to use a pair of pliers to get a good grip on it and gently
try to pull it out. Replace the fuse, the faceplate, and
the screws, making sure that the front face is securely
seated so not to lessen the water seal.
4.
If the communication is hooked up properly and all informa-
tion fields are properly displayed on the “radar information”
page, but the unit starts to warm up but you never see a
count down to standby on the screen and then radar com-
munication is lost after one minute. The voltage supply to
the Radar Antenna or the gauge wire supplying the voltage
may be to small.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Softkeys
Colorline 31
Frequency 31
Range 31
Range 31
Sensitivity 30
Split 31
Refuel 93
Routes 78
Symbology 65
Specifications 113
Split 31
create 47
display/hide 50
edit 50
Symbology 65
System 69
navigate 50
T
S
Satellites 71
Sea Clutter
Harbor 63
Manual 63
Offshore 63
Time 70
Sensitivity 30
Size 14
Trails 51
Create 52
Tune 92
Type 14
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Visit our website:
www.lowrance.com
© Copyright 2008
All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And DNowanvloiacdo. Holding AS
*988-0176-01B*
|
Kyocera Cell Phone K132 User Manual
La Crosse Technology Weather Radio c86371 User Manual
LG Electronics Cell Phone VM701 User Manual
LG Electronics Model Vehicle 32S18 User Manual
LG Electronics Projection Television RU 44SZ63D User Manual
Lightolier Indoor Furnishings 1101H User Manual
LOREX Technology Digital Camera DMC2030 Series User Manual
Lumens Technology Network Card DC A11 User Manual
Makita Drill NH1030 User Manual
Midland Radio Portable Radio WR11 User Manual