Locke Lawn Mower TRM 3083 User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hook Up  
2. Adjust the mower’s hitch to the tractor’s drawbar  
height. Keep frame level, with tractor and mower  
on level ground. Place framing level across the  
square frame segments front to rear and adjust  
hitch height to level the frame.  
1. Engage Clevis swivel hitch or ball hitch to tractor  
drawbar using draw bar pin or ball supplied.  
IMPORTANT  
3. Attach the mower with a 3/4" hitch pin and secure it  
with a lock pin. Always use a pin that contains a  
safety locking device to prevent it form falling out.  
4. Lower the tongue jack until the weight of the mower  
is fully removed from the jack, then remove the jack.  
Store the jack on the left hand frame rail. A storage  
base is located on top of the frame tube.  
For correct leveling, adjust Reel Mower unit  
tongue height so that the front and rear jack-  
shafts are equal distances above ground level.  
5. Attach the safety chain on the frame hitch to the  
tractor. Adjust the chain length to remove all slack  
except what is necessary to permit turning of the  
mower. Lock the hook securely on the chain.  
6. The driveline from the tractor is one with a constant  
velocity. Always attach the end with the constant  
velocity to the tractor’s PTO shaft. Attach the other  
end to the splined jackshaft on the center of the  
transport frame.  
7. Move the driveline back and forth to insure that it is  
secured on the PTO shaft of the tractor and power  
divider input shaft on the mower.  
8. Secure the chain on the driveling around mower  
frame to restrict the outer shield of the driveline  
from rotating.  
Leveling the Frame – Tongue Adjust-  
ments  
The bolt on section of the tongue can be rotated to  
three different positions. The clevis can be rotated  
two different ways. This provides 6 different heights  
for leveling the frame. (See diagram below)  
NOTE:  
A chain is supplied with each driveline. This chain  
must be attached to the shield cone of each driveline  
and to an anchor ring on the cutter hitch.  
9. Should the driveline shaft require shortening:  
a. Hold the half shafts next to each other in the  
shortest working position and mark them.  
b. Shorten inner and outer guard tubes equally.  
c. Shorten inner and outer sliding profiles by the  
same length as the guard tubes.  
d. Proper overlap is a minimum of one-half the  
length of each tube, with both tubes being of  
equal length.  
e. Round off all sharp edges and remove burrs.  
Grease sliding profiles.  
10. Route the cylinder hoses through the hose support  
and connect to tractor remote outlets. Refer to “  
Hydraulic Plumbing” on page 9 for proper hook-up.  
Quick disconnect hydraulic fittings for your tractor  
are available from your dealer.  
NOTE: The use of a drawbar hung between the 3-  
point hitch arms is not recommended; a straight  
drawbar attached to the rear axle housing in the  
standard SAE position to the PTO is preferable.  
Hydraulic Hook-up  
Tractor Hook-Up  
Insert the hydraulic hose quick-disconnect plugs into the  
female quick-disconnects on the tractor external hydrau-  
lics.  
1. Back the tractor up close to the hitch. Raise or  
lower, with the hitch tongue jack, in order to  
level the mower’s frame.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S8ECTION  
2
OPERATION  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Slow Moving Vehicle Symbol  
HIGH PRESSURE  
FLUID HAZARD  
To prevent serious injury  
or death from escaping  
hydraulic fluid:  
Visually check all hydraulic  
lines and hoses BEFORE  
applying pressure.  
Amber Reflector 53315  
Red Reflector 53316  
Relieve pressure on system  
before repairing, adjusting  
or disconnecting.  
Use paper or cardboard,  
Not BODY PARTS, to check  
for suspected leaks.  
50022071  
NOTICE TO OWNER  
An OPERATOR'S MANUAL and a WARRANTY REGISTRATION  
were attached to this implement during final inspection at  
the factory.  
If they were not attached at the time of purchase, please  
contact your selling dealer at once.  
1. Read and understand Manual BEFORE operating  
the implement.  
50022074  
50022079  
50022072  
50022064  
DANGER  
WARNING  
EXCESSIVE SPEED  
HAZARD  
To Prevent Serious Injury or Death:  
Do Not Exceed 20 mph maximum  
transport speed. Loss of vehicle  
control and/or machine damage  
can result  
THROWN OBJECT HAZARD  
To prevent serious injury or death from thrown objects:  
Operate with all guards installed in good condition.  
Stop operation if bystanders come within several hundred feet.  
50022070  
50022075  
DANGER  
ROTATING DRIVELINE  
DANGER  
CONTACT CAN CAUSE DEATH  
KEEP AWAY  
ROTATING BLADES-KEEP AWAY  
DO NOT OPERATE WITHOUT  
To prevent serious injury or death from rotating  
reel blade contact.  
All driveline guards, tractor and equipment  
shields in place  
Drivelines securely attached at both ends  
Never allow riders, especially children on tractor.  
Keep bystanders away from mowing area.  
Driveline guards that turn freely on diveline  
Keep guards on machine.  
50022065  
Keep hands, feet, hair and clothing away  
from moving parts.  
50022077  
DANGER  
WARNING  
To Prevent serious injury or death:  
RAISED WING HAZARD-KEEP AWAY  
To prevent serious injury or death:  
Si no lee ingles, pida ayuda a alguien que  
si lo lea para que le taduzca las medidas  
de seguridad.  
Transport only with transport locks securely engaged.  
Lock wing before walking or working underneath.  
Read and understand Operator's Manual before using.  
50022078  
Do not permit riders on the tractor or mower. Never  
carry child on tractor seat.  
Operate with guards installed and in good condition.  
Operate only with tractor equipped with ROPS and  
seat belts.  
DANGER  
Keep away from moving parts.  
Stop engine, set brake and wait for all moving parts to  
stop before dismounting.  
Be sure lights and reflectors required by law are clean  
and in good working order before transporting.  
ROTATING DRIVELINE  
HAZARD  
Do not allow children to operate mower.  
Clean debris from mowing area.  
Shield Missing  
Do Not Operate  
Do not operate in the raised position.  
Support securely before working beneath unit.  
Review safety instructions annually.  
50022066  
50022073  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D19ECALS CONTINUED  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TORQUE SPECIFICATIONS  
Proper torque for American fasteners used on Locke Turf equipment.  
Recommended Torque in Foot Pounds (Newton Meters). *  
WRENCH  
SIZE (IN.) “A”  
BOLT DIAMETER  
(IN.) “B” AND  
THREAD SIZE  
1/4 –20 UNC  
SAE  
GRADE 2  
SAE  
GRADE 5  
SAE  
GRADE 8  
AMERICAN  
7/16  
7/16  
6 (7)  
8 (11)  
10 (13)  
12 (16)  
14 (18)  
Bolt Head Markings  
1/4 –28 UNF  
5/16 – 18 UNC  
5/16 – 24 UNF  
3/8 – 16 UNC  
3/8 – 24 UNF  
7/16 – 14 UNC  
7/16 – 20 UNF  
1/2 – 13 UNC  
1/2 – 20 UNF  
9/16 – 12 UNC  
9/16 – 18 UNF  
5/8 – 11 UNC  
5/8 – 18 UNF  
3/4 – 10 UNC  
3/4 –16 UNF  
7/8 – 9 UNC  
6 (8)  
1/2  
11 (15)  
17 (23)  
25 (33)  
1/2  
13 (17)  
19 (26)  
27 (37)  
9/16  
20 (27)  
31 (42)  
44 (60)  
9/16  
23 (31)  
35 (47)  
49 (66)  
5/8  
32 (43)  
49 (66)  
70 (95)  
5/8  
36 (49)  
55 (75)  
78 (106)  
3/4  
49 (66)  
76 (103)  
106 (144)  
120 (163)  
153 (207)  
172 (233)  
212 (287)  
240 (325)  
376 (509)  
420 (569)  
606 (821)  
668 (905)  
909 (1232)  
995 (1348)  
1019 (1381)  
1288 (1745)  
1444 (1957)  
1817 (2462)  
2013 (2728)  
2382 (3228)  
2712 (1992)  
3161 (4283)  
SAE Grade 2  
(No Dashes)  
3/4  
55 (75)  
85 (115)  
7/8  
70 (95)  
109 (148)  
122 (165)  
150 (203)  
170 (230)  
266 (360)  
297 (402)  
430 (583)  
474 (642)  
644 (873)  
705 (955)  
721 (977)  
795 (1077)  
890 (1206)  
1120 (1518)  
1241 (1682)  
1470 (1992)  
1672 (2266)  
1950 (2642)  
7/8  
79 (107)  
97 (131)  
110 (149)  
144 (195)  
192 (260)  
166 (225)  
184 (249)  
250 (339)  
274 (371)  
280 (379)  
354 (480)  
397 (538)  
500 (678)  
553 (749)  
655 (887)  
746 (1011)  
870 (1179)  
15/16  
15/16  
1-1/8  
1-1/8  
1-5/16  
1-5/16  
1-1/2  
1-1/2  
1-1/2  
1-11/16  
1-11/16  
1-7/8  
1-7/8  
2-1/16  
2-1/16  
2-1/4  
SAE Grade 5  
(3 Dashes)  
7/8 – 14 UNF  
1 –8 UNC  
1 – 12 UNF  
1 – 14 UNF  
1-1/8 – 7 UNC  
1-1/8 – 12 UNF  
1-1/4 – 7 UNC  
1-1/4 – 12 UNF  
1-3/8 – 6 UNC  
1-3/8 – 12 UNF  
1-1/2 – 6 UNC  
Wrench  
Size "A"  
SAE Grade 8  
(6 Dashes)  
2-1/4  
1-1/2 – 12 UNF  
979 (1327)  
2194 (2973)  
3557 (4820)  
Proper torque for American fasteners used on Locke Turf equipment.  
Recommended Torque in Foot Pounds (Newton Meters). *  
METRIC  
WRENCH  
SIZE  
BOLT  
DIA.  
ASTM  
4.6  
ASTM  
8.8  
ASTM  
9.8  
ASTM  
10.9  
(mm) “A”  
8
(mm) “B”  
5
1.8 (2.4)  
3 (4)  
5.1 (6.9)  
8.7 (12)  
21.1 (29)  
42 (57)  
6.5 (8.8)  
11.1 (15)  
27 (37)  
10  
13  
16  
18  
21  
24  
30  
33  
36  
41  
46  
6
8
7.3 (10)  
14.5 (20)  
25 (34)  
40 (54)  
62 (84)  
122 (165)  
Wrench  
Size "A"  
8.8  
10  
12  
14  
16  
20  
22  
24  
27  
30  
53 (72)  
74 (100)  
118 (160)  
167 (226)  
325 (440)  
443 (600)  
563 (763)  
821 (1112)  
1119 (1516)  
73 (99)  
93 (126)  
116 (157)  
181 (245)  
148 (201)  
230 (312)  
449 (608)  
611 (828)  
778 (1054)  
1138 (1542)  
1547 (2096)  
Numbers appearing on bolt heads  
Indicate ASTM class.  
*Use 75% of the specified torque value  
for plated fasteners. Use 85% of the  
specified torque values for lubricated  
fasteners.  
211 (286)  
418 (566)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lenovo Computer Monitor LXH GJ17L3 User Manual
LOREX Technology Home Security System L15D400 User Manual
Makita Chainsaw UC3003A User Manual
Makita Cordless Drill DA390D User Manual
Makita Impact Driver BTW120SA User Manual
Martin Audio Portable Speaker Screen 4 User Manual
McCulloch Lawn Mower Accessory M53 170WFP User Manual
Melissa Blender 646 057 User Manual
Mercedes Benz Automobile SLK 230 User Manual
Metabo Staple Gun KG 16 User Manual